Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.16.0-2-amd64] (local build)
- Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: SAMSUNG SpinPoint F2 EG
- Device Model: SAMSUNG HD103SI
- Serial Number: S1VSJDWS705499
- LU WWN Device Id: 5 0024e9 001c45049
- Firmware Version: 1AG01118
- User Capacity: 1 000 204 886 016 bytes [1,00 TB]
- Sector Size: 512 bytes logical/physical
- Device is: In smartctl database [for details use: -P show]
- ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
- Local Time is: Thu Jun 14 06:06:53 2018 MSK
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x00) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Disabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: (13234) seconds.
- Offline data collection
- capabilities: (0x7b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 221) minutes.
- Conveyance self-test routine
- recommended polling time: ( 23) minutes.
- SCT capabilities: (0x003f) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000f 100 084 051 Pre-fail Always - 125
- 3 Spin_Up_Time 0x0007 081 081 011 Pre-fail Always - 6620
- 4 Start_Stop_Count 0x0032 094 094 000 Old_age Always - 6527
- 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
- 7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
- 8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 11144
- 9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 16507
- 10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
- 11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0
- 12 Power_Cycle_Count 0x0032 094 094 000 Old_age Always - 5925
- 13 Read_Soft_Error_Rate 0x000e 100 084 000 Old_age Always - 125
- 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 5619
- 184 End-to-End_Error 0x0033 001 001 000 Pre-fail Always - 4977
- 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 4660
- 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
- 190 Airflow_Temperature_Cel 0x0022 078 058 000 Old_age Always - 22 (Min/Max 18/22)
- 194 Temperature_Celsius 0x0022 073 057 000 Old_age Always - 27 (Min/Max 18/27)
- 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 1008510
- 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
- 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
- 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
- 199 UDMA_CRC_Error_Count 0x003e 100 099 000 Old_age Always - 13521
- 200 Multi_Zone_Error_Rate 0x000a 100 099 000 Old_age Always - 0
- 201 Soft_Read_Error_Rate 0x000a 253 253 000 Old_age Always - 0
- SMART Error Log Version: 1
- ATA Error Count: 280 (device log contains only the most recent five errors)
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 280 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 18 85 a3 e1 Error: UNC at LBA = 0x01a38518 = 27493656
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- c8 00 08 18 85 a3 e1 08 05:16:30.370 READ DMA
- ea 00 00 ff 47 c7 a0 08 05:16:29.490 FLUSH CACHE EXT
- ec 00 00 00 00 00 a0 08 05:16:29.110 IDENTIFY DEVICE
- ef 03 46 00 00 00 a0 08 05:16:29.110 SET FEATURES [Set transfer mode]
- ec 00 00 00 00 00 a0 08 05:16:29.090 IDENTIFY DEVICE
- Error 279 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 18 85 a3 e1 Error: UNC at LBA = 0x01a38518 = 27493656
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- c8 00 08 18 85 a3 e1 08 05:16:26.630 READ DMA
- c8 00 08 10 85 a3 e1 08 05:16:26.630 READ DMA
- c8 00 08 08 85 a3 e1 08 05:16:26.630 READ DMA
- c8 00 08 00 85 a3 e1 08 05:16:26.630 READ DMA
- c8 00 08 f8 84 a3 e1 08 05:16:26.630 READ DMA
- Error 278 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 48 16 c0 e1 Error: UNC at LBA = 0x01c01648 = 29365832
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- c8 00 08 48 16 c0 e1 08 00:02:03.280 READ DMA
- c8 00 08 80 ec a1 e1 08 00:02:03.280 READ DMA
- c8 00 20 60 ec a1 e1 08 00:02:03.270 READ DMA
- c8 00 08 a0 1c 81 e1 08 00:02:03.260 READ DMA
- c8 00 00 60 96 87 e1 08 00:02:03.250 READ DMA
- Error 277 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 48 16 c0 e1 Error: UNC at LBA = 0x01c01648 = 29365832
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- c8 00 08 48 16 c0 e1 08 00:01:36.970 READ DMA
- ca 00 01 df 1e 04 e1 08 00:01:36.970 WRITE DMA
- ea 00 00 df 51 85 a0 08 00:01:36.950 FLUSH CACHE EXT
- c8 00 08 d8 51 85 e1 08 00:01:36.950 READ DMA
- c8 00 18 c0 c0 c6 e1 08 00:01:36.950 READ DMA
- Error 276 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 48 16 c0 e1 Error: UNC at LBA = 0x01c01648 = 29365832
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- c8 00 08 48 16 c0 e1 08 00:01:31.580 READ DMA
- c8 00 28 88 9f c6 e1 08 00:01:31.570 READ DMA
- c8 00 08 70 cb 93 e1 08 00:01:31.560 READ DMA
- c8 00 20 50 cb 93 e1 08 00:01:31.550 READ DMA
- c8 00 98 40 bd 9e e1 08 00:01:31.540 READ DMA
- SMART Self-test log structure revision number 1
- Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
- # 1 Short offline Completed without error 00% 16507 -
- # 2 Extended offline Interrupted (host reset) 10% 16506 -
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement