Create a new version of paste:

smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.16.0-2-amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint F2 EG
Device Model:     SAMSUNG HD103SI
Serial Number:    S1VSJDWS705499
LU WWN Device Id: 5 0024e9 001c45049
Firmware Version: 1AG01118
User Capacity:    1 000 204 886 016 bytes [1,00 TB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is:    Thu Jun 14 06:06:53 2018 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(13234) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 221) minutes.
Conveyance self-test routine
recommended polling time: 	 (  23) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   100   084   051    Pre-fail  Always       -       125
  3 Spin_Up_Time            0x0007   081   081   011    Pre-fail  Always       -       6620
  4 Start_Stop_Count        0x0032   094   094   000    Old_age   Always       -       6527
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   100   100   051    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0025   100   100   015    Pre-fail  Offline      -       11144
  9 Power_On_Hours          0x0032   097   097   000    Old_age   Always       -       16507
 10 Spin_Retry_Count        0x0033   100   100   051    Pre-fail  Always       -       0
 11 Calibration_Retry_Count 0x0012   100   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   094   094   000    Old_age   Always       -       5925
 13 Read_Soft_Error_Rate    0x000e   100   084   000    Old_age   Always       -       125
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       5619
184 End-to-End_Error        0x0033   001   001   000    Pre-fail  Always       -       4977
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       4660
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   078   058   000    Old_age   Always       -       22 (Min/Max 18/22)
194 Temperature_Celsius     0x0022   073   057   000    Old_age   Always       -       27 (Min/Max 18/27)
195 Hardware_ECC_Recovered  0x001a   100   100   000    Old_age   Always       -       1008510
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   100   099   000    Old_age   Always       -       13521
200 Multi_Zone_Error_Rate   0x000a   100   099   000    Old_age   Always       -       0
201 Soft_Read_Error_Rate    0x000a   253   253   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 280 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 280 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 18 85 a3 e1  Error: UNC at LBA = 0x01a38518 = 27493656

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 18 85 a3 e1 08      05:16:30.370  READ DMA
  ea 00 00 ff 47 c7 a0 08      05:16:29.490  FLUSH CACHE EXT
  ec 00 00 00 00 00 a0 08      05:16:29.110  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 08      05:16:29.110  SET FEATURES [Set transfer mode]
  ec 00 00 00 00 00 a0 08      05:16:29.090  IDENTIFY DEVICE

Error 279 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 18 85 a3 e1  Error: UNC at LBA = 0x01a38518 = 27493656

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 18 85 a3 e1 08      05:16:26.630  READ DMA
  c8 00 08 10 85 a3 e1 08      05:16:26.630  READ DMA
  c8 00 08 08 85 a3 e1 08      05:16:26.630  READ DMA
  c8 00 08 00 85 a3 e1 08      05:16:26.630  READ DMA
  c8 00 08 f8 84 a3 e1 08      05:16:26.630  READ DMA

Error 278 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 48 16 c0 e1  Error: UNC at LBA = 0x01c01648 = 29365832

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 48 16 c0 e1 08      00:02:03.280  READ DMA
  c8 00 08 80 ec a1 e1 08      00:02:03.280  READ DMA
  c8 00 20 60 ec a1 e1 08      00:02:03.270  READ DMA
  c8 00 08 a0 1c 81 e1 08      00:02:03.260  READ DMA
  c8 00 00 60 96 87 e1 08      00:02:03.250  READ DMA

Error 277 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 48 16 c0 e1  Error: UNC at LBA = 0x01c01648 = 29365832

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 48 16 c0 e1 08      00:01:36.970  READ DMA
  ca 00 01 df 1e 04 e1 08      00:01:36.970  WRITE DMA
  ea 00 00 df 51 85 a0 08      00:01:36.950  FLUSH CACHE EXT
  c8 00 08 d8 51 85 e1 08      00:01:36.950  READ DMA
  c8 00 18 c0 c0 c6 e1 08      00:01:36.950  READ DMA

Error 276 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 48 16 c0 e1  Error: UNC at LBA = 0x01c01648 = 29365832

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 48 16 c0 e1 08      00:01:31.580  READ DMA
  c8 00 28 88 9f c6 e1 08      00:01:31.570  READ DMA
  c8 00 08 70 cb 93 e1 08      00:01:31.560  READ DMA
  c8 00 20 50 cb 93 e1 08      00:01:31.550  READ DMA
  c8 00 98 40 bd 9e e1 08      00:01:31.540  READ DMA

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     16507         -
# 2  Extended offline    Interrupted (host reset)      10%     16506         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.