smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.16.0-2-amd64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F2 EG Device Model: SAMSUNG HD103SI Serial Number: S1VSJDWS705499 LU WWN Device Id: 5 0024e9 001c45049 Firmware Version: 1AG01118 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Thu Jun 14 06:06:53 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13234) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 221) minutes. Conveyance self-test routine recommended polling time: ( 23) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 084 051 Pre-fail Always - 125 3 Spin_Up_Time 0x0007 081 081 011 Pre-fail Always - 6620 4 Start_Stop_Count 0x0032 094 094 000 Old_age Always - 6527 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 11144 9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 16507 10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 094 094 000 Old_age Always - 5925 13 Read_Soft_Error_Rate 0x000e 100 084 000 Old_age Always - 125 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 5619 184 End-to-End_Error 0x0033 001 001 000 Pre-fail Always - 4977 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 4660 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 078 058 000 Old_age Always - 22 (Min/Max 18/22) 194 Temperature_Celsius 0x0022 073 057 000 Old_age Always - 27 (Min/Max 18/27) 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 1008510 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 100 099 000 Old_age Always - 13521 200 Multi_Zone_Error_Rate 0x000a 100 099 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 253 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 280 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 280 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 18 85 a3 e1 Error: UNC at LBA = 0x01a38518 = 27493656 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 18 85 a3 e1 08 05:16:30.370 READ DMA ea 00 00 ff 47 c7 a0 08 05:16:29.490 FLUSH CACHE EXT ec 00 00 00 00 00 a0 08 05:16:29.110 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 05:16:29.110 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 08 05:16:29.090 IDENTIFY DEVICE Error 279 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 18 85 a3 e1 Error: UNC at LBA = 0x01a38518 = 27493656 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 18 85 a3 e1 08 05:16:26.630 READ DMA c8 00 08 10 85 a3 e1 08 05:16:26.630 READ DMA c8 00 08 08 85 a3 e1 08 05:16:26.630 READ DMA c8 00 08 00 85 a3 e1 08 05:16:26.630 READ DMA c8 00 08 f8 84 a3 e1 08 05:16:26.630 READ DMA Error 278 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 48 16 c0 e1 Error: UNC at LBA = 0x01c01648 = 29365832 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 48 16 c0 e1 08 00:02:03.280 READ DMA c8 00 08 80 ec a1 e1 08 00:02:03.280 READ DMA c8 00 20 60 ec a1 e1 08 00:02:03.270 READ DMA c8 00 08 a0 1c 81 e1 08 00:02:03.260 READ DMA c8 00 00 60 96 87 e1 08 00:02:03.250 READ DMA Error 277 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 48 16 c0 e1 Error: UNC at LBA = 0x01c01648 = 29365832 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 48 16 c0 e1 08 00:01:36.970 READ DMA ca 00 01 df 1e 04 e1 08 00:01:36.970 WRITE DMA ea 00 00 df 51 85 a0 08 00:01:36.950 FLUSH CACHE EXT c8 00 08 d8 51 85 e1 08 00:01:36.950 READ DMA c8 00 18 c0 c0 c6 e1 08 00:01:36.950 READ DMA Error 276 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 48 16 c0 e1 Error: UNC at LBA = 0x01c01648 = 29365832 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 48 16 c0 e1 08 00:01:31.580 READ DMA c8 00 28 88 9f c6 e1 08 00:01:31.570 READ DMA c8 00 08 70 cb 93 e1 08 00:01:31.560 READ DMA c8 00 20 50 cb 93 e1 08 00:01:31.550 READ DMA c8 00 98 40 bd 9e e1 08 00:01:31.540 READ DMA SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 16507 - # 2 Extended offline Interrupted (host reset) 10% 16506 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.