System Information
------------------

Raspberry Pi Zero Rev 1.3
NAME="Alpine Linux"
ID=alpine
VERSION_ID=3.23.4
PRETTY_NAME="Alpine Linux v3.23"

cat: can't open '/etc/rpi-issue': No such file or directory

Linux alpine-headless 6.12.81-0-rpi #1-Alpine Sat Apr 11 15:34:37 UTC 2026 armv6l Linux
Revision	: 900093
Serial		: 000000000dfe596e
Model		: Raspberry Pi Zero Rev 1.3
Throttled flag  : throttled=0x0
Camera Information
------------------

Camera          : supported=0 detected=0, libcamera interfaces=0

Videocore information
---------------------

Feb 11 2026 18:31:36
Copyright (c) 2012 Broadcom
version ce768004a1c9657e60b33b0cc413d8e07320cb0d (clean) (release) (start)

alloc failures:     0
compactions:        0
legacy block fails: 0


Filesystem information
----------------------
Filesystem           1K-blocks      Used Available Use% Mounted on
devtmpfs                 10240         0     10240   0% /dev
shm                     219068         0    219068   0% /dev/shm
/dev/sda1              7970572     80244   7890328   1% /media/usb
tmpfs                   219068     28148    190920  13% /
tmpfs                    87628       136     87492   0% /run
/dev/loop0               35200     35200         0 100% /.modloop

Filename				Type		Size		Used		Priority

Package version information
---------------------------
/usr/bin/raspinfo: line 226: apt-cache: command not found
/usr/bin/raspinfo: line 227: apt-cache: command not found
/usr/bin/raspinfo: line 228: apt-cache: command not found
/usr/bin/raspinfo: line 229: apt-cache: command not found
/usr/bin/raspinfo: line 230: apt-cache: command not found
/usr/bin/raspinfo: line 231: apt-cache: command not found

Networking Information
----------------------

eth0      Link encap:Ethernet  HWaddr m.m.m.m
          inet addr:x.x.x.x  Bcast:x.x.x.x  Mask:x.x.x.x
          inet6 addr: y.y.y.y.y.y.y.y/64 Scope:Global
          inet6 addr: y::y.y.y.y/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:7129 errors:0 dropped:28 overruns:0 frame:0
          TX packets:2802 errors:0 dropped:1 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:7432131 (7.0 MiB)  TX bytes:312348 (305.0 KiB)

lo        Link encap:Local Loopback
          inet addr:x.x.x.x  Mask:x.x.x.x
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)


USB Information
---------------

unable to initialize usb spec/:  Bus 001.Port 001: Dev 001, Class=root_hub, Driver=dwc_otg/1p, 480M
    |__ Port 001: Dev 002, If 0, Class=[unknown], Driver=hub/4p, 480M
        |__ Port 001: Dev 003, If 0, Class=[unknown], Driver=asix, 480M
        |__ Port 004: Dev 004, If 0, Class=[unknown], Driver=usb-storage, 480M

Display Information
-------------------

Using console with legacy
Framebuffer: /dev/fb0

mode "608x384-0"
	# D: 0.000 MHz, H: 0.000 kHz, V: 0.000 Hz
	geometry 608 384 608 384 32
	timings 0 0 0 0 0 0 0
	accel false
	rgba 8/16,8/8,8/0,8/24
endmode

tvservice not installed

Audio Information
-------------------

/usr/bin/raspinfo: line 157: aplay: command not found

/usr/bin/raspinfo: line 159: aplay: command not found

/usr/bin/raspinfo: line 161: systemctl: command not found

pactl not installed

config.txt
----------

aphy_params_current=547
arm_freq=1000
arm_freq_min=700
audio_pwm_mode=514
camera_auto_detect=-1
config_hdmi_boost=7
core_freq=400
disable_auto_turbo=1
disable_commandline_tags=2
disable_fw_kms_setup=-1
display_hdmi_rotate=-1
display_lcd_rotate=-1
dphy_params_current=547
dvfs=3
enable_tvout=1
enable_uart=1
force_eeprom_read=1
force_ethernet_phy_address=-1
force_pwm_open=1
framebuffer_ignore_alpha=1
framebuffer_swap=1
gpu_freq=300
hdmi_enable_4kp60=-1
hdmi_safe=1
ignore_lcd=1
init_uart_clock=0x2dc6c00
initial_turbo=60
max_framebuffers=-1
over_voltage_avs=0x249f0
overscan_bottom=16
overscan_left=24
overscan_right=24
overscan_top=16
pause_burst_frames=1
pciex4_reset=1
pmic_turbo_threshold=600
program_serial_random=1
ramfsaddr=-1
sdram_freq=450
total_mem=512
hdmi_force_cec_address:0=65535
hdmi_force_cec_address:1=65535
hdmi_force_hotplug:0=1
hdmi_force_hotplug:1=1
hdmi_group:0=2
hdmi_group:1=2
hdmi_mode:0=4
hdmi_mode:1=4
hdmi_pixel_freq_limit:0=0x9a7ec80
device_tree=-
kernel=boot/vmlinuz-rpi
overlay_prefix=overlays/
ramfsfile=boot/initramfs-rpi
hdmi_cvt:0=
hdmi_cvt:1=
hdmi_edid_filename:0=
hdmi_edid_filename:1=
hdmi_timings:0=
hdmi_timings:1=

cmdline.txt
-----------
coherent_pool=1M snd_bcm2835.enable_headphones=0 cgroup_disable=memory bcm2708_fb.fbwidth=608 bcm2708_fb.fbheight=384 bcm2708_fb.fbswap=1 smsc95xx.macaddr=B8:27:EB:FE:59:6E vc_mem.mem_base=0x1ec00000 vc_mem.mem_size=0x20000000  modules=loop,squashfs,sd-mod,usb-storage quiet console=tty1

pin configuration
-----------------

 0: ip    -- | hi // ID_SDA/GPIO0 = input
 1: ip    -- | hi // ID_SCL/GPIO1 = input
 2: ip    -- | hi // GPIO2 = input
 3: ip    -- | hi // GPIO3 = input
 4: ip    -- | hi // GPIO4 = input
 5: ip    -- | hi // GPIO5 = input
 6: ip    -- | hi // GPIO6 = input
 7: ip    -- | hi // GPIO7 = input
 8: ip    -- | hi // GPIO8 = input
 9: ip    -- | lo // GPIO9 = input
10: ip    -- | lo // GPIO10 = input
11: ip    -- | lo // GPIO11 = input
12: ip    -- | lo // GPIO12 = input
13: ip    -- | lo // GPIO13 = input
14: a0    -- | hi // GPIO14 = TXD0
15: a0    -- | hi // GPIO15 = RXD0
16: ip    -- | lo // GPIO16 = input
17: ip    -- | lo // GPIO17 = input
18: ip    -- | lo // GPIO18 = input
19: ip    -- | lo // GPIO19 = input
20: ip    -- | lo // GPIO20 = input
21: ip    -- | lo // GPIO21 = input
22: ip    -- | lo // GPIO22 = input
23: ip    -- | lo // GPIO23 = input
24: ip    -- | lo // GPIO24 = input
25: ip    -- | lo // GPIO25 = input
26: ip    -- | lo // GPIO26 = input
27: ip    -- | lo // GPIO27 = input
28: ip    -- | hi // SDA0/GPIO28 = input
29: ip    -- | hi // SCL0/GPIO29 = input
30: ip    -- | lo // NC/GPIO30 = input
31: ip    -- | lo // NC/GPIO31 = input
32: op -- -- | lo // CAM_GPIO1/GPIO32 = output
33: ip    -- | lo // NC/GPIO33 = input
34: ip    -- | hi // NC/GPIO34 = input
35: ip    -- | hi // NC/GPIO35 = input
36: ip    -- | hi // NC/GPIO36 = input
37: ip    -- | lo // NC/GPIO37 = input
38: ip    -- | lo // NC/GPIO38 = input
39: ip    -- | lo // NC/GPIO39 = input
40: ip    -- | lo // NC/GPIO40 = input
41: op -- -- | lo // CAM_GPIO0/GPIO41 = output
42: ip    -- | lo // NC/GPIO42 = input
43: ip    -- | lo // NC/GPIO43 = input
44: ip    -- | lo // NC/GPIO44 = input
45: ip    -- | lo // NC/GPIO45 = input
46: ip    -- | lo // HDMI_HPD_N/GPIO46 = input
47: op -- -- | lo // STATUS_LED_N/GPIO47 = output
48: a0    -- | lo // SD_CLK_R/GPIO48 = SD0_CLK
49: a0    -- | hi // SD_CMD_R/GPIO49 = SD0_CMD
50: a0    -- | hi // SD_DATA0_R/GPIO50 = SD0_DAT0
51: a0    -- | hi // SD_DATA1_R/GPIO51 = SD0_DAT1
52: a0    -- | hi // SD_DATA2_R/GPIO52 = SD0_DAT2
53: a0    -- | hi // SD_DATA3_R/GPIO53 = SD0_DAT3

vcdbg log messages
------------------

007476.308: brfs: File read: /mfs/sd/config.txt
007476.470: brfs: File read: 264 bytes
007502.305: brfs: File read: /mfs/sd/usercfg.txt
007502.450: board: boardrev 900093 otp 900093
007502.596: brfs: File read: 119 bytes
007931.117: brfs: File read: /mfs/sd/config.txt
007931.276: brfs: File read: 264 bytes
007957.117: brfs: File read: /mfs/sd/usercfg.txt
007957.498: gpioman: gpioman_get_pin_num: pin LEDS_PWR_OK not defined
007971.688: gpioman: gpioman_get_pin_num: pin WL_LPO_CLK not defined
007971.715: gpioman: gpioman_get_pin_num: pin BT_ON not defined
007971.735: gpioman: gpioman_get_pin_num: pin WL_ON not defined
007994.020: gpioman: gpioman_get_pin_num: pin LEDS_PWR_OK not defined
007994.074: *** Restart logging
007994.100: brfs: File read: 119 bytes
008148.577: hdmi: HDMI:hdmi_get_state is deprecated, use hdmi_get_display_state instead
008148.599: HDMI0: hdmi_pixel_encoding: 162000000
008148.867: vec: vec_middleware_power_on: vec_base: 0x7e806000 rev-id 0x00002708 @ vec: 0x7e806100 @ 0x00000420 enc: 0x7e806060 @ 0x00000220 cgmsae: 0x7e80605c @ 0x00000000
010159.294: brfs: File read: /mfs/sd/boot/initramfs-rpi
010159.319: Loaded 'boot/initramfs-rpi' to 0x0 size 0x5b4646
010166.154: initramfs (boot/initramfs-rpi) loaded to 0x1ba3b000 (size 0x5b4646)
010175.917: dtb_file 'bcm2708-rpi-zero.dtb'
010175.944: brfs: File read: 5981766 bytes
010292.316: brfs: File read: /mfs/sd/bcm2708-rpi-zero.dtb
010292.342: Loaded 'bcm2708-rpi-zero.dtb' to 0x100 size 0x7522
010306.086: brfs: File read: 29986 bytes
010727.246: brfs: File read: /mfs/sd/overlays/overlay_map.dtb
010768.339: brfs: File read: 5971 bytes
010883.141: brfs: File read: /mfs/sd/config.txt
010883.253: brfs: File read: 264 bytes
010909.143: brfs: File read: /mfs/sd/usercfg.txt
010916.251: brfs: File read: 119 bytes
011043.786: brfs: File read: /mfs/sd/cmdline.txt
011043.816: Read command line from file 'cmdline.txt':
011043.831: 'modules=loop,squashfs,sd-mod,usb-storage quiet console=tty1'
011136.478: gpioman: gpioman_get_pin_num: pin WL_ON not defined
011155.808: brfs: File read: 60 bytes
013710.161: brfs: File read: /mfs/sd/boot/vmlinuz-rpi
013710.190: Loaded 'boot/vmlinuz-rpi' to 0x8000 size 0x6f6f50
013710.237: Device tree loaded to 0x1ba33600 (size 0x790a)
013710.452: gpioman: gpioman_get_pin_num: pin EMMC_ENABLE not defined
013725.291: Watchdog stopped
013725.305: arm_loader: Starting ARM with 448MB
017882.878: vchiq_core: vchiq_init_state: slot_zero = 0x97980000, is_master = 1

dmesg log
---------

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 6.12.81-0-rpi (buildozer@build-3-23-armhf) (cc (Alpine 15.2.0) 15.2.0, GNU ld (GNU Binutils) 2.45.1) #1-Alpine Sat Apr 11 15:34:37 UTC 2026
[    0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] OF: fdt: Machine model: Raspberry Pi Zero Rev 1.3
[    0.000000] random: crng init done
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Reserved memory: created CMA memory pool at 0x17800000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] OF: reserved mem: 0x17800000..0x1b7fffff (65536 KiB) map reusable linux,cma
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x000000001bffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000001bffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001bffffff]
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Kernel command line: coherent_pool=1M snd_bcm2835.enable_headphones=0 cgroup_disable=memory bcm2708_fb.fbwidth=608 bcm2708_fb.fbheight=384 bcm2708_fb.fbswap=1 smsc95xx.macaddr=m.m.m.m vc_mem.mem_base=0x1ec00000 vc_mem.mem_size=0x20000000  modules=loop,squashfs,sd-mod,usb-storage quiet console=tty1
[    0.000000] cgroup: Disabling memory control group subsystem
[    0.000000] Unknown kernel command line parameters "modules=loop,squashfs,sd-mod,usb-storage", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 114688
[    0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns
[    0.000053] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns
[    0.000142] bcm2835: system timer (irq = 27)
[    0.000760] Console: colour dummy device 80x30
[    0.000794] printk: legacy console [tty1] enabled
[    0.000896] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736)
[    0.040222] CPU: Testing write buffer coherency: ok
[    0.040301] pid_max: default: 32768 minimum: 301
[    0.040676] LSM: initializing lsm=capability
[    0.040984] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.041020] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.044249] Setting up static identity map for 0x8220 - 0x8258
[    0.044833] Memory: 364644K/458752K available (10249K kernel code, 1601K rwdata, 3408K rodata, 304K init, 356K bss, 26764K reserved, 65536K cma-reserved)
[    0.045574] devtmpfs: initialized
[    0.054135] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
[    0.054432] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.054474] futex hash table entries: 256 (order: 0, 3072 bytes, linear)
[    0.062267] pinctrl core: initialized pinctrl subsystem
[    0.063836] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.065742] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.070506] audit: initializing netlink subsys (disabled)
[    0.071794] thermal_sys: Registered thermal governor 'step_wise'
[    0.072042] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[    0.072070] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.072503] Serial: AMBA PL011 UART driver
[    0.077908] bcm2835-mbox 2000b880.mailbox: mailbox enabled
[    0.080492] audit: type=2000 audit(0.070:1): state=initialized audit_enabled=0 res=1
[    0.100507] raspberrypi-firmware soc:firmware: Attached to firmware from 2026-02-11T18:31:36, variant start
[    0.110533] raspberrypi-firmware soc:firmware: Firmware hash is ce768004a1c9657e60b33b0cc413d8e07320cb0d
[    0.124862] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[    0.133860] bcm2835-dma 20007000.dma-controller: DMA legacy API manager, dmachans=0x1
[    0.135952] SCSI subsystem initialized
[    0.136351] usbcore: registered new interface driver usbfs
[    0.136438] usbcore: registered new interface driver hub
[    0.136522] usbcore: registered new device driver usb
[    0.137132] pps_core: LinuxPPS API ver. 1 registered
[    0.137158] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    0.137200] PTP clock support registered
[    0.151496] clocksource: Switched to clocksource timer
[    0.152438] VFS: Disk quotas dquot_6.6.0
[    0.152540] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.184296] NET: Registered PF_INET protocol family
[    0.184567] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.192152] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.192211] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.192316] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.192395] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.192490] TCP: Hash tables configured (established 4096 bind 4096)
[    0.192608] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.192648] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.192976] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.193825] RPC: Registered named UNIX socket transport module.
[    0.193857] RPC: Registered udp transport module.
[    0.193867] RPC: Registered tcp transport module.
[    0.193876] RPC: Registered tcp-with-tls transport module.
[    0.193885] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.194574] Trying to unpack rootfs image as initramfs...
[    1.272847] Freeing initrd memory: 5844K
[    2.285123] Initialise system trusted keyrings
[    2.286753] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    2.289073] NFS: Registering the id_resolver key type
[    2.289134] Key type id_resolver registered
[    2.289148] Key type id_legacy registered
[    2.289204] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    2.289223] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    2.291050] Key type asymmetric registered
[    2.291087] Asymmetric key parser 'x509' registered
[    2.291598] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    2.291653] io scheduler mq-deadline registered
[    2.291670] io scheduler kyber registered
[    2.291837] io scheduler bfq registered
[    2.296226] pinctrl-bcm2835 20200000.gpio: GPIO_OUT persistence: yes
[    2.302380] ledtrig-cpu: registered to indicate activity on CPUs
[    2.311626] bcm2708_fb soc:fb: FB found 1 display(s)
[    2.334357] Console: switching to colour frame buffer device 76x48
[    2.337717] bcm2708_fb soc:fb: Registered framebuffer for display 0, size 608x384
[    2.357103] bcm2835-rng 20104000.rng: hwrng registered
[    2.358288] vc-mem: phys_addr:0x00000000 mem_base=0x1ec00000 mem_size:0x20000000(512 MiB)
[    2.391039] brd: module loaded
[    2.407725] loop: module loaded
[    2.409401] Loading iSCSI transport class v2.0-870.
[    2.416124] usbcore: registered new interface driver smsc95xx
[    2.416162] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    3.143603] Core Release: 2.80a
[    3.143645] Setting default values for core params
[    3.143672] Finished setting default values for core params
[    3.343563] Using Buffer DMA mode
[    3.343591] Periodic Transfer Interrupt Enhancement - disabled
[    3.343603] Multiprocessor Interrupt Enhancement - disabled
[    3.343613] OTG VER PARAM: 0, OTG VER FLAG: 0
[    3.343678] Dedicated Tx FIFOs mode
[    3.344480] INFO:: FIQ DMA bounce buffers: virt = d7914000 dma = 0x97914000 len=9024
[    3.344533] FIQ FSM acceleration enabled for :
[    3.344533] Non-periodic Split Transactions
[    3.344533] Periodic Split Transactions
[    3.344533] High-Speed Isochronous Endpoints
[    3.344533] Interrupt/Control Split Transaction hack enabled
[    3.344552] dwc_otg: Microframe scheduler enabled
[    3.344651] INFO:: FIQ on core 0
[    3.344672] INFO:: FIQ ASM at c076282c length 36
[    3.344690] INFO:: MPHI regs_base at dc810000
[    3.344728] dwc_otg 20980000.usb: DWC OTG Controller
[    3.344780] dwc_otg 20980000.usb: new USB bus registered, assigned bus number 1
[    3.344840] dwc_otg 20980000.usb: irq 56, io mem 0x00000000
[    3.344897] Init: Port Power? op_state=1
[    3.344908] Init: Power Port (0)
[    3.345292] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[    3.345326] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.345346] usb usb1: Product: DWC OTG Controller
[    3.345360] usb usb1: Manufacturer: Linux 6.12.81-0-rpi dwc_otg_hcd
[    3.345374] usb usb1: SerialNumber: 20980000.usb
[    3.347213] hub 1-0:1.0: USB hub found
[    3.347325] hub 1-0:1.0: 1 port detected
[    3.349407] dwc_otg: FIQ enabled
[    3.349438] dwc_otg: NAK holdoff enabled
[    3.349448] dwc_otg: FIQ split-transaction FSM enabled
[    3.349751] Module dwc_common_port init
[    3.350587] usbcore: registered new interface driver usb-storage
[    3.351348] mousedev: PS/2 mouse device common for all mice
[    3.358741] sdhci: Secure Digital Host Controller Interface driver
[    3.358773] sdhci: Copyright(c) Pierre Ossman
[    3.359845] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.360923] hid: raw HID events driver (C) Jiri Kosina
[    3.362447] usbcore: registered new interface driver usbhid
[    3.362484] usbhid: USB HID core driver
[    3.363242] bcm2835_vchiq 2000b840.mailbox: there is not valid maps for state default
[    3.372750] armv6-pmu arm-pmu: hw perfevents: no irqs for PMU, sampling events not supported
[    3.373510] hw perfevents: enabled with armv6_1176 PMU driver, 3 (00000007) counters available
[    3.377633] Initializing XFRM netlink socket
[    3.377811] Key type dns_resolver registered
[    3.471797] Indeed it is in host mode hprt0 = 00021501
[    3.564170] registered taskstats version 1
[    3.564380] Loading compiled-in X.509 certificates
[    3.599548] uart-pl011 20201000.serial: cts_event_workaround enabled
[    3.600481] 20201000.serial: ttyAMA0 at MMIO 0x20201000 (irq = 81, base_baud = 0) is a PL011 rev2
[    3.619455] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[    3.620887] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[    3.624739] of_cfs_init
[    3.624933] of_cfs_init: OK
[    3.629121] clk: Disabling unused clocks
[    3.630356] PM: genpd: Disabling unused power domains
[    3.709721] sdhost-bcm2835 20202000.mmc: loaded - DMA enabled (>1)
[    3.710955] Freeing unused kernel image (initmem) memory: 304K
[    3.710987] Kernel memory protection not selected by kernel config.
[    3.711032] Run /init as init process
[    3.711045]   with arguments:
[    3.711052]     /init
[    3.711060]   with environment:
[    3.711068]     HOME=/
[    3.711076]     TERM=linux
[    3.711083]     modules=loop,squashfs,sd-mod,usb-storage
[    3.761800] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    3.761983] Indeed it is in host mode hprt0 = 00001101
[    3.931318] Alpine Init 3.13.0-r0
[    3.940740] Loading boot drivers...
[    3.959886] mmc0: host does not support reading read-only switch, assuming write-enable
[    3.961056] mmc0: new SD card at address 911b
[    3.962781] mmcblk0: mmc0:911b SU01G 969 MiB
[    3.966824]  mmcblk0: p1
[    3.967866] mmcblk0: mmc0:911b SU01G 969 MiB (quirks 0x00004000)
[    3.988346] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    3.995519] Loading boot drivers: ok.
[    4.012957] Mounting boot media...
[    4.052200] usb 1-1: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.11
[    4.052247] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    4.052266] usb 1-1: Product: USB 2.0 Hub
[    4.055370] hub 1-1:1.0: USB hub found
[    4.055550] hub 1-1:1.0: 4 ports detected
[    4.471639] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[    4.672574] usb 1-1.1: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01
[    4.672624] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    4.672642] usb 1-1.1: Product: AX88772
[    4.672657] usb 1-1.1: Manufacturer: ASIX Elec. Corp.
[    4.672674] usb 1-1.1: SerialNumber: 000001
[    4.851708] usb 1-1.4: new high-speed USB device number 4 using dwc_otg
[    5.052378] usb 1-1.4: New USB device found, idVendor=abcd, idProduct=1234, bcdDevice= 1.00
[    5.052430] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    5.052450] usb 1-1.4: Product: 1
[    5.052464] usb 1-1.4: Manufacturer: 1
[    5.052477] usb 1-1.4: SerialNumber: Љ
[    5.056901] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[    5.061631] scsi host0: usb-storage 1-1.4:1.0
[    5.063934] usbcore: registered new interface driver uas
[    6.082716] scsi 0:0:0:0: Direct-Access     General  UDisk            5.00 PQ: 0 ANSI: 2
[    6.137765] sd 0:0:0:0: [sda] 15974400 512-byte logical blocks: (8.18 GB/7.62 GiB)
[    6.138426] sd 0:0:0:0: [sda] Write Protect is off
[    6.138463] sd 0:0:0:0: [sda] Mode Sense: 0b 00 00 08
[    6.138822] sd 0:0:0:0: [sda] No Caching mode page found
[    6.138854] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    6.152356]  sda: sda1
[    6.153854] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    8.982289] Mounting boot media: ok.
[    8.996725] Loading user settings from /media/sda1/headless.apkovl.tar.gz...
[    9.082994] Loading user settings from /media/sda1/headless.apkovl.tar.gz: ok.
[   10.753800] Installing packages to root filesystem...
[   12.183785] Installing packages to root filesystem: ok.
[   17.727219] loop0: detected capacity change from 0 to 70160
[   17.737173] F2FS-fs (loop0): Magic Mismatch, valid(0xf2f52010) - read(0x2dbf0951)
[   17.737224] F2FS-fs (loop0): Can't find valid F2FS filesystem in 1th superblock
[   17.737391] F2FS-fs (loop0): Magic Mismatch, valid(0xf2f52010) - read(0x590ea5f6)
[   17.737422] F2FS-fs (loop0): Can't find valid F2FS filesystem in 2th superblock
[   21.262826] rpi-gpiomem 20200000.gpiomem: window base 0x20200000 size 0x00001000
[   21.272335] rpi-gpiomem 20200000.gpiomem: initialised 1 regions as /dev/gpiomem
[   22.581801] asix 1-1.1:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:003:10] driver [Asix Electronics AX88772A] (irq=POLL)
[   22.591785] Asix Electronics AX88772A usb-001:003:10: attached PHY driver (mii_bus:phy_addr=usb-001:003:10, irq=POLL)
[   22.592606] asix 1-1.1:1.0 eth0: register 'asix' at usb-20980000.usb-1.1, ASIX AX88772 USB 2.0 Ethernet, m.m.m.m
[   22.592837] usbcore: registered new interface driver asix
[   24.412990] NET: Registered PF_PACKET protocol family
[   24.644530] NET: Registered PF_INET6 protocol family
[   24.647069] Segment Routing with IPv6
[   24.647162] In-situ OAM (IOAM) with IPv6
[   30.291362] asix 1-1.1:1.0 eth0: configuring for phy/internal link mode
[   32.487597] asix 1-1.1:1.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx