API tools faq
paste
Advertisement
Agat-Aquarius

Elbrus 401-PC boot-time configuration menu

Agat-Aquarius
Jan 25th, 2016
1,088
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 15.99 KB | None | 0 0
raw download clone embed print report
  1. CPU#00: Trying to load boot configuration file from Drive [4]... Success
  2. CPU#00: Using boot parameters from Drive [4]
  3.  
  4. Autoboot in 03 sec. PRESS SPACE TO DISABLE IT.
  5. Key pressed. Autoboot canceled.
  6. CPU#00: Starting menu.
  7.  
  8. BOOT SETUP
  9. Press command letter, or press 'h' to get help
  10. :h
  11.  
  12. HELP
  13. 'p' or 's' - load and Start file
  14. 'c' - Change boot parameters
  15. 'u' - show cUrrent parameters
  16. 'd' - show Disks and partitions
  17. 'm' - save params to NVRAM
  18. 'b' - start Boot.conf menu
  19. '`', '~' - enter enhanced cmd mode
  20.  
  21. BOOT SETUP
  22. Press command letter, or press 'h' to get help
  23. :u
  24.  
  25. Current Settings:
  26. drive_number: '4'
  27. partition_number: '0'
  28. command_string: ''
  29. filename: ''
  30. initrdfilename: ''
  31. autoboot in: '10'
  32.  
  33. BOOT SETUP
  34. Press command letter, or press 'h' to get help
  35. :d
  36. CPU#00: Drive [2]: IDE - PCI BUS[1]:DEV[2]:FUNC[0], MCST IDE Secondary Master - ULTIMATE CF CARD
  37. CPU#00: Partition [0]: W95 FAT32 (LBA)
  38. CPU#00: Drive [4]: SATA - PCI BUS[1]:DEV[3]:FUNC[0], MCST SATA Port [0] - KINGSTON SMS200S3120G
  39. CPU#00: Partition [0]: Linux EXT3
  40. CPU#00: Partition [1]: Linux swap
  41. CPU#00: Partition [2]: Linux EXT3
  42. CPU#00: Partition [3]: Extended
  43. CPU#00: Partition [4]: Linux EXT3
  44. CPU#00: Partition [5]: Linux EXT3
  45. CPU#00: Partition [6]: Linux EXT3
  46. CPU#00: Drive [5]: SATA - PCI BUS[1]:DEV[3]:FUNC[0], MCST SATA Port [1] - WDC WD1003FZEX-00MK2A0
  47. CPU#00: Unknown partition table
  48. CPU#00: Drive [6]: ATAPI device
  49.  
  50. BOOT SETUP
  51. Press command letter, or press 'h' to get help
  52. :`
  53.  
  54. ENHANCED CMD MODE
  55. Enter command, 'help' to get help, or Esc to exit
  56. :
  57. # help
  58. COMMAND HELP
  59. Use 'Tab' to complete commands
  60. List of commands:
  61.  
  62. help - Shows boot console help
  63. boot - Enter boot menu
  64. set - Allows to set parameters:
  65. boot_device - Boot device
  66. sp - Serial ports settings:
  67. output_dis - Serial port output disable flag
  68. input_dis - Serial port input disable flag
  69. memory - Memory:
  70. limit - Limited size
  71. csum - Control sum settings:
  72. calc - Calculate and print control sums, when loading files
  73. check - Check loaded file
  74. save - Save control sum of next loaded file to NVRAM
  75. kernel_check - Kernel check loaded file
  76. apmdz - Turn on/off usage of "Echelon-E" APMDZ
  77. rtc - real time clock settings:
  78. time - set/show current time
  79. date - set/show current date
  80. weekday - set/show current day of the week
  81. password - Enter password menu:
  82. enable - Allows to enable new password
  83. disable - Allows to disable password
  84. change - Allows to set new password
  85. mode - Password check mode (load/modify or modify only)
  86. serial_num - Machine serial number
  87. drive_init_delay - Delay in seconds, before any drive initialization starts
  88. mb_version - Machine version magic (arch_type)
  89. cpu_type - CPU type
  90. chipset - Chipset configuration:
  91. default - Set parameters to default values
  92. mc - Memory controller parameters:
  93. freq - MC/CPU Frequency Ratio
  94. dir - Enable SC directory
  95. dircache - Enable SC directory cache
  96. dirmcl - Multi-cluster directory mode
  97. dma_ord_en - DMA Ordering Enable
  98. hw1_2rdma - Enable 2 RDMA
  99. hw1_snrd32 - Enable SNRD32
  100. hw1_dpack64 - Enable 64-byte data packets
  101. hw1_i2ri - IN -> RI conversion
  102. hw1_scrqprior - Highest Priority for requests from SC
  103. hw1_dcindscr - Directory Cache Index Scrambling
  104. hw1_b63761wa - Bug63761 (2 IOLinks) workaround
  105. mcil_bit - MC interleaving
  106. en - Enable MC channel
  107. mcln - Memory clean start
  108. ee - ECC check & correct
  109. ri - Refresh Interval
  110. sldrd - Detection of Sealed Reads
  111. lintel_hw_init - Usage of lintel to init unknown hardware : 1/0 - ON/OFF
  112. iohub - IOHub settings:
  113. ch1 - the channel 1 configuration
  114. ahci - AHCI configuration:
  115. controller - tune AHCI controller:
  116. enable - enable controller or port
  117. disable - disable controller or port
  118. ide - IDE configuration:
  119. mcst - MCST IDE configuration:
  120. maxdma - The highest DMA mode
  121. controller - tune IDE controller:
  122. enable - enable controller or drive
  123. disable - disable controller or drive
  124. eth - Ethernet Controllers configuration:
  125. 100 - ETH100 configuration:
  126. mac - MAC address base
  127. speed - Data speed
  128. mode - Normal/Loopback
  129. full - Init Block Full-Bit
  130. 1000 - ETH1000 configuration:
  131. mac - MAC address base
  132. speed - Data speed
  133. mode - Normal/Loopback
  134. full - Init Block Full-Bit
  135. controller - tune ETH controller:
  136. enable - enable ETH controller
  137. disable - disable ETH controller
  138. aoe - ATA over Ethernet (AoE) settings:
  139. server - initial requests settings:
  140. mac - destination MAC address
  141. major - destination AoE major address
  142. minor - destination AoE minor address
  143. timeout - timeout settings:
  144. break - timeout (ms) to break exchange with AoE server
  145. vga - tune VGA controllers:
  146. primary - configure primary VGA controller
  147. output_disable - Video consol output disable flag
  148. usb - USB configuration:
  149. ehci - USB EHCI (USB 2.0) configuration:
  150. port_power_delay - delay after switching ports power on
  151. controller - usb controller control:
  152. enable - enable usb controller
  153. disable - disable usb controller
  154. ohci - USB OHCI (USB 1.1) configuration:
  155. port_power_delay - delay after switching ports power on
  156. controller - usb controller control:
  157. enable - enable usb controller
  158. disable - disable usb controller
  159. test_mem - Set test memory flag
  160. fruid - FRUID configuration:
  161. data - setup FRUID
  162. unlock - unlock FRUID area
  163. mb_name - set motherboard product name
  164. auto_install - Set auto install flag
  165. get - Allows to get parameters:
  166. boot_device - Boot device
  167. version - Prints info:
  168. boot - Version of boot program
  169. sp - Serial ports settings:
  170. output_dis - Serial port output disable flag
  171. input_dis - Serial port input disable flag
  172. memory - Memory:
  173. regions - Regions
  174. limit - Limited size
  175. csum - Control sum settings:
  176. calc - Calculate and print control sums, when loading files
  177. check - Check loaded file
  178. kernel_check - Kernel check loaded file
  179. apmdz - Turn on/off usage of "Echelon-E" APMDZ
  180. rtc - real time clock settings:
  181. time - set/show current time
  182. date - set/show current date
  183. weekday - set/show current day of the week
  184. password - Enter password menu:
  185. status - Password status
  186. serial_num - Machine serial number
  187. drives - Show current drives and partitions
  188. drive_init_delay - Delay in seconds, before any drive initialization starts
  189. mb_version - Machine version magic (arch_type)
  190. cpu_type - CPU type
  191. mc - Memory controller parameters:
  192. freq - MC/CPU Frequency Ratio
  193. dir - Enable SC directory
  194. dircache - Enable SC directory cache
  195. dirmcl - Multi-cluster directory mode
  196. dma_ord_en - DMA Ordering Enable
  197. hw1_2rdma - Enable 2 RDMA
  198. hw1_snrd32 - Enable SNRD32
  199. hw1_dpack64 - Enable 64-byte data packets
  200. hw1_i2ri - IN -> RI conversion
  201. hw1_scrqprior - Highest Priority for requests from SC
  202. hw1_dcindscr - Directory Cache Index Scrambling
  203. hw1_b63761wa - Bug63761 (2 IOLinks) workaround
  204. mcil_bit - MC interleaving
  205. en - Enable MC channel
  206. mcln - Memory clean start
  207. ee - ECC check & correct
  208. ri - Refresh Interval
  209. sldrd - Detection of Sealed Reads
  210. lintel_hw_init - Usage of lintel to init unknown hardware : 1/0 - ON/OFF
  211. iohub - IOHub settings:
  212. ch1 - the channel 1 configuration
  213. ahci - AHCI configuration:
  214. controller - tune AHCI controller
  215. ide - IDE configuration:
  216. mcst - MCST IDE configuration:
  217. maxdma - The highest DMA mode
  218. controller - tune IDE controller
  219. eth - Ethernet Controllers configuration:
  220. 100 - ETH100 configuration:
  221. mac - MAC address base
  222. speed - Data speed
  223. mode - Normal/Loopback
  224. full - Init Block Full-Bit
  225. 1000 - ETH1000 configuration:
  226. mac - MAC address base
  227. speed - Data speed
  228. mode - Normal/Loopback
  229. full - Init Block Full-Bit
  230. controller - tune ETH controller
  231. aoe - ATA over Ethernet (AoE) settings:
  232. server - initial requests settings:
  233. mac - destination MAC address
  234. major - destination AoE major address
  235. minor - destination AoE minor address
  236. timeout - timeout settings:
  237. break - timeout (ms) to break exchange with AoE server
  238. vga - tune VGA controllers:
  239. primary - configure primary VGA controller
  240. output_disable - Video consol output disable flag
  241. usb - USB configuration:
  242. ehci - USB EHCI (USB 2.0) configuration:
  243. port_power_delay - delay after switching ports power on
  244. controller - usb controller control
  245. ohci - USB OHCI (USB 1.1) configuration:
  246. port_power_delay - delay after switching ports power on
  247. controller - usb controller control
  248. test_mem - Get test memory flag: 1/0 - ON/OFF
  249. fruid - FRUID configuration:
  250. data - print FRUID info
  251. unlock - print FRUID area lock status
  252. mb_name - get motherboard product name
  253. auto_install - Get auto install flag: 1/0 - ON/OFF
  254. reset - Init Hard reset signal
  255. tests - Enter System of Testing and Diagnostic Programs menu
  256.  
  257. # get boot_device
  258. 4
  259.  
  260. # get version boot
  261. BOOT E2S
  262. VERSION: release-2.13.3.0-E2S ::::::: ( /tags/release-2.13.3.0-E2S at revision 3816 )
  263. BUILT BY neo
  264. TARGET: mono
  265. ON Nov 2 2015
  266. AT 18:05:42
  267. COMPILER: lcc:1.17.12:Nov-27-2012:e2k-linux.cross:i386-linux Thread model: posix gcc version 3.4.6 compatible.
  268. FLAGS: -DDEBUG_TEST_BOOTBLOCK -DALLOC_IDE_PRD_TBL_STATICALLY -DISO9660_USE_CASH -DISO9660_MANGLING_NAMES -DINITRD -DISO9660_USE_LOCAL_HEAP -DMCST_SATA -DMCST2_SATA -DNEW_AHCI_ATAPI -DDEBUG_TESTS -DRESET_REQUEST_ENABLE -DENABLE_STDP -DFAT_EFI_SUPPORT -DPCC_SIMULATE_CARD_OS_STARTED_THEN_START -DPCC_READ_CARD_FILES_BY_PARTS -DDO_NOT_INIT_MGA_IF_MGA_3D_PRESENT -DBUG52542 -DENABLE_X86EMU_VIDEO_INIT -DRELEASE
  269.  
  270. # get serial_num
  271. 0
  272.  
  273. # get drives
  274. CPU#00: Drive [2]: IDE - PCI BUS[1]:DEV[2]:FUNC[0], MCST IDE Secondary Master - ULTIMATE CF CARD
  275. CPU#00: Partition [0]: W95 FAT32 (LBA)
  276. CPU#00: Drive [4]: SATA - PCI BUS[1]:DEV[3]:FUNC[0], MCST SATA Port [0] - KINGSTON SMS200S3120G
  277. CPU#00: Partition [0]: Linux EXT3
  278. CPU#00: Partition [1]: Linux swap
  279. CPU#00: Partition [2]: Linux EXT3
  280. CPU#00: Partition [3]: Extended
  281. CPU#00: Partition [4]: Linux EXT3
  282. CPU#00: Partition [5]: Linux EXT3
  283. CPU#00: Partition [6]: Linux EXT3
  284. CPU#00: Drive [5]: SATA - PCI BUS[1]:DEV[3]:FUNC[0], MCST SATA Port [1] - WDC WD1003FZEX-00MK2A0
  285. CPU#00: Unknown partition table
  286. CPU#00: Drive [6]: ATAPI device
  287.  
  288. # get mb_version
  289. 23
  290.  
  291. # get cpu_type
  292. 0
  293.  
  294. # get mc freq
  295. Usage:
  296. get mc freq <node>
  297. <node> - Node number (Range: 0 - 3)
  298.  
  299.  
  300. #
  301.  
  302. # get mc freq 0
  303. 0x0
  304.  
  305. #
  306.  
  307. # get mc freq 3
  308. 0x0
  309.  
  310. # get mc ee
  311. Usage:
  312. get mc ee <node>
  313. <node> - Node number (Range: 0 - 3)
  314.  
  315.  
  316. #
  317.  
  318. # get mc ee 0
  319. 0x1
  320.  
  321. # get iohub ch1
  322. USAGE:
  323. get iohub ch1 <node> <iolink>
  324.  
  325. <node> - node number IOHub connected to.
  326. The maximum node number is 3
  327. <iolink> - the <node> IOLink number IOHub connected to.
  328. The maximum IOLink number is 0.
  329.  
  330.  
  331.  
  332. #
  333.  
  334. # get iohub ch1 0 0
  335. off
  336.  
  337.  
  338. # get ahci cont
  339. # get ahci controller
  340. AHCI Controller on (bus=1,slot=3,func=0) enabled
  341.  
  342. #
  343.  
  344. # get ahci controller
  345.  
  346. # get vga primary
  347. [1] core: 0x0, link: 0x0, bus: 0x3, slot: 0x0, func: 0x0, ven: 0x1002, dev: 0x6779, rev: 0x0, classcode: 0x30000 is selected!
  348.  
  349.  
  350. # set vga primary 0
  351. [0] core: 0x0, link: 0x0, bus: 0x2, slot: 0x3, func: 0x0, ven: 0x126F, dev: 0x718, rev: 0xA0, classcode: 0x30000 is selected!
  352.  
  353.  
  354. # get vga primary
  355. [0] core: 0x0, link: 0x0, bus: 0x2, slot: 0x3, func: 0x0, ven: 0x126F, dev: 0x718, rev: 0xA0, classcode: 0x30000 is selected!
  356.  
  357.  
  358. #
  359.  
  360. # get vga primary
  361.  
  362. # set vga primary 1
  363. [1] core: 0x0, link: 0x0, bus: 0x3, slot: 0x0, func: 0x0, ven: 0x1002, dev: 0x6779, rev: 0x0, classcode: 0x30000 is selected!
  364.  
  365.  
  366. # get usb ehci controller
  367. enabled
  368.  
  369. # get fruid data
  370. Reading FRUID from NVRAM:
  371. Reading FRUID:
  372. Header version: 01
  373.  
  374. Internal Use Area:
  375. Version: 01
  376. mac_addr: 98A7B0002580
  377. mb_ver: 17
  378.  
  379. Board Info Area:
  380. Version: 01
  381. Mfg date: 24:00 Wed 06 Oct 2015
  382. Board manufacturer: ÐæçõŸ üúᝠ<=== {unknown text encoding}
  383. Board product name: Ðí÷•2S-ò¡
  384. Board serial number: 1510XX
  385. Board part number: Ðô÷ç˜.469555.300 <== {«ТВГИ», очевидно}
  386. FRU file ID: 85556085
  387. Product version: 00
  388.  
  389. # get fruid unlock
  390. FRUID area currently unlocked
  391.  
  392. # get mb_name
  393.  
  394.  
  395. # get apmdz
  396. 0
  397.  
  398. # boot
  399.  
  400. boot# ?
  401. Error - label '?' not found
  402.  
  403.  
  404. boot# help
  405. Error - label 'help' not found
  406.  
  407.  
  408. boot# auto
  409. CPU#00: Label 'auto' found, loading parameters
  410.  
  411. Trying to load and start image with following parameters:
  412. drive_number: '4'
  413. partition_number: '0'
  414. command_string: 'console=tty0 console=ttyS0,115200 consoleblank=0 hardreset REBOOT root=/dev/sda3 video=DVI-D-1:1024x768-24@60 video=VGA-1:1024x768-24@60 fbcon=map:10'
  415. filename: '/boot/image-033.6.57'
  416. initrdfilename: ''
  417.  
  418. CPU#00: Reading: File - '/boot/image-033.6.57', Drive - 4, Partition - 0, Buffer - 0xFF0000
  419.  
  420. Loaded: 0%
  421. Loaded: 13%
  422. Loaded: 27%
  423. Loaded: 40%
  424. Loaded: 54%
  425. Loaded: 68%
  426. Loaded: 81%
  427. Loaded: 95%
  428. Loaded: 100%
  429. CPU#00: Reading completed. File size: 30903056 bytes
  430. CPU#00: Ethernet Interfaces stopped
  431. CPU#00: USB stopped
  432. CPU#00: SPI frequency dropped to 12.5MHz
  433. Kernel ROM loader's initialization started.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!