Guest User

Untitled

a guest
May 4th, 2018
125
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. 11:46:15 AMM122
  2. === Diagnostics ===
  3. RepRapFirmware for Duet 2 WiFi/Ethernet version 2.0(RTOS)RC1 running on Duet Ethernet 1.02 or later + DueX5
  4. Board ID: 08DDM-9FAM2-LW4SD-6JTDL-3S86R-KJW3X
  5. Used output buffers: 1 of 20 (16 max)
  6. === RTOS ===
  7. Static ram: 28484
  8. Dynamic ram: 96480 of which 0 recycled
  9. Exception stack ram used: 368
  10. Never used ram: 5740
  11. Task NETWORK ready, free stack 440
  12. Task HEAT blocked, free stack 1204
  13. Task MAIN running, free stack 3832
  14. === Platform ===
  15. Last reset 00:03:14 ago, cause: software
  16. Last software reset at 2018-05-04 11:43, reason: Hard fault, spinning module GCodes, available RAM 5512 bytes (slot 3)
  17. Software reset code 0x4033 HFSR 0x40000000, CFSR 0x00010000, ICSR 0x0041f803, BFAR 0xe000ed38, SP 0x200049dc
  18. Stack: 00444d4f 00424f82 61000000 20008f5c 20003420 0000000a 20000180 200001e0 00000000 00000038 00000000 00000000 2000b3c8 2000a480 00000000 00000038 20004cf4 a5a5a5a5 a5a5a5a5 a5a5a5a5 00424fc3 2000b3c8 0042afe1 40080000
  19. Error status: 0
  20. Free file entries: 8
  21. SD card 0 detected, interface speed: 20.0MBytes/sec
  22. SD card longest block write time: 0.0ms
  23. MCU temperature: min 27.9, current 28.2, max 28.3
  24. Supply voltage: min 24.2, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0
  25. Driver 0: ok, SG min/max not available
  26. Driver 1: standstill, SG min/max not available
  27. Driver 2: standstill, SG min/max not available
  28. Driver 3: ok, SG min/max 0/0
  29. Driver 4: standstill, SG min/max not available
  30. Driver 5: standstill, SG min/max not available
  31. Driver 6: standstill, SG min/max not available
  32. Driver 7: standstill, SG min/max not available
  33. Driver 8: standstill, SG min/max not available
  34. Driver 9: standstill, SG min/max not available
  35. Expansion motor(s) stall indication: no
  36. Date/time: 2018-05-04 11:46:14
  37. Slowest main loop (seconds): 0.006140; fastest: 0.000089
  38. === Move ===
  39. Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 204, MinFreeDm 198, MaxWait: 0ms, Underruns: 0, 0
  40. Scheduled moves: 106, completed moves: 93
  41. Bed compensation in use: none
  42. Bed probe heights: 0.000 0.000 0.000 0.000 0.000
  43. === Heat ===
  44. Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
  45. Heater 0 is on, I-accum = 0.0
  46. Heater 1 is on, I-accum = 0.3
  47. === GCodes ===
  48. Segments left: 1
  49. Stack records: 4 allocated, 0 in use
  50. Movement lock held by file
  51. http is idle in state(s) 0
  52. telnet is idle in state(s) 0
  53. file is doing "G10" in state(s) 0
  54. serial is idle in state(s) 0
  55. aux is idle in state(s) 0
  56. daemon is idle in state(s) 0
  57. queue is idle in state(s) 0
  58. autopause is idle in state(s) 0
  59. Code queue is empty.
  60. === Network ===
  61. Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
  62. HTTP sessions: 1 of 8
  63. Interface state: 5
  64. === Filament sensors ===
  65. Extruder 0 sensor: ok
  66. === Expansion ===
  67. DueX I2C errors 0
RAW Paste Data