11:46:15 AMM122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.0(RTOS)RC1 running on Duet Ethernet 1.02 or later + DueX5
Board ID: 08DDM-9FAM2-LW4SD-6JTDL-3S86R-KJW3X
Used output buffers: 1 of 20 (16 max)
=== RTOS ===
Static ram: 28484
Dynamic ram: 96480 of which 0 recycled
Exception stack ram used: 368
Never used ram: 5740
Task NETWORK ready, free stack 440
Task HEAT blocked, free stack 1204
Task MAIN running, free stack 3832
=== Platform ===
Last reset 00:03:14 ago, cause: software
Last software reset at 2018-05-04 11:43, reason: Hard fault, spinning module GCodes, available RAM 5512 bytes (slot 3)
Software reset code 0x4033 HFSR 0x40000000, CFSR 0x00010000, ICSR 0x0041f803, BFAR 0xe000ed38, SP 0x200049dc
Stack: 00444d4f 00424f82 61000000 20008f5c 20003420 0000000a 20000180 200001e0 00000000 00000038 00000000 00000000 2000b3c8 2000a480 00000000 00000038 20004cf4 a5a5a5a5 a5a5a5a5 a5a5a5a5 00424fc3 2000b3c8 0042afe1 40080000
Error status: 0
Free file entries: 8
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 27.9, current 28.2, max 28.3
Supply voltage: min 24.2, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0
Driver 0: ok, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: ok, SG min/max 0/0
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Expansion motor(s) stall indication: no
Date/time: 2018-05-04 11:46:14
Slowest main loop (seconds): 0.006140; fastest: 0.000089
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 204, MinFreeDm 198, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 106, completed moves: 93
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.3
=== GCodes ===
Segments left: 1
Stack records: 4 allocated, 0 in use
Movement lock held by file
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G10" in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
Interface state: 5
=== Filament sensors ===
Extruder 0 sensor: ok
=== Expansion ===
DueX I2C errors 0