API tools faq
paste
Advertisement
electrotwelve

config.txt

electrotwelve
Aug 13th, 2017
125
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 29.38 KB | None | 0 0
raw download clone embed print report
  1. # Smoothieboard configuration file, see http://smoothieware.org/configuring-smoothie
  2. # NOTE Lines must not exceed 132 characters, and '#' characters mean what follows is ignored
  3. ## Robot module configurations : general handling of movement G-codes and slicing into moves
  4.  
  5. # Basic motion configuration
  6. default_feed_rate 4000 # Default speed (mm/minute) for G1/G2/G3 moves
  7. default_seek_rate 4000 # Default speed (mm/minute) for G0 moves
  8. mm_per_arc_segment 0.5 # Fixed length for line segments that divide arcs, 0 to disable
  9. #mm_per_line_segment 5 # Cut lines into segments this size
  10. mm_max_arc_error 0.01 # The maximum error for line segments that divide arcs 0 to disable
  11. # note it is invalid for both the above be 0
  12. # if both are used, will use largest segment length based on radius
  13.  
  14. # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
  15. # See http://smoothieware.org/stepper-motors
  16. arm_solution corexy
  17. alpha_steps_per_mm 80 # Steps per mm for alpha ( X ) stepper
  18. beta_steps_per_mm 80 # Steps per mm for beta ( Y ) stepper
  19. gamma_steps_per_mm 400 # Steps per mm for gamma ( Z ) stepper
  20.  
  21. # Planner module configuration : Look-ahead and acceleration configuration
  22. # See http://smoothieware.org/motion-control
  23. planner_queue_size 32 # DO NOT CHANGE THIS UNLESS YOU KNOW EXACTLY WHAT YOUR ARE DOING
  24. acceleration 1000 # Acceleration in mm/second/second.
  25. z_acceleration 250 # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
  26. junction_deviation 0.05 # See http://smoothieware.org/motion-control#junction-deviation
  27. acceleration_ticks_per_second 1000 # Number of times per second the speed is updated
  28. #z_junction_deviation 0.0 # For Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
  29.  
  30. # Cartesian axis speed limits
  31. x_axis_max_speed 30000 # Maximum speed in mm/min
  32. y_axis_max_speed 30000 # Maximum speed in mm/min
  33. z_axis_max_speed 300 # Maximum speed in mm/min
  34.  
  35. # Stepper module configuration
  36. # microseconds_per_step_pulse 1 # Duration of step pulses to stepper drivers, in microseconds
  37. # base_stepping_frequency 100000 # Base frequency for stepping
  38.  
  39. # Pins are defined as ports, and pin numbers, appending "!" to the number will invert a pin
  40. # See http://smoothieware.org/pin-configuration and http://smoothieware.org/pinout
  41. alpha_step_pin 2.1 # Pin for alpha stepper step signal
  42. alpha_dir_pin 0.11 # Pin for alpha stepper direction, add '!' to reverse direction
  43. alpha_en_pin 0.10 # Pin for alpha enable pin
  44. alpha_current 1.5 # X stepper motor current
  45. alpha_max_rate 30000.0 # Maximum rate in mm/min
  46.  
  47. beta_step_pin 2.2 # Pin for beta stepper step signal
  48. beta_dir_pin 0.20 # Pin for beta stepper direction, add '!' to reverse direction
  49. beta_en_pin 0.19 # Pin for beta enable
  50. beta_current 1.5 # Y stepper motor current
  51. beta_max_rate 30000.0 # Maxmimum rate in mm/min
  52.  
  53. gamma_step_pin 2.3 # Pin for gamma stepper step signal
  54. gamma_dir_pin 0.22! # Pin for gamma stepper direction, add '!' to reverse direction
  55. gamma_en_pin 0.21 # Pin for gamma enable
  56. gamma_current 1.5 # Z stepper motor current
  57. gamma_max_rate 300.0 # Maximum rate in mm/min
  58.  
  59. ## Extruder module configuration
  60. # See http://smoothieware.org/extruder
  61. extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
  62. extruder.hotend.steps_per_mm 139.6873 # Steps per mm for extruder stepper
  63. extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  64. extruder.hotend.acceleration 500 # Acceleration for the stepper motor mm/sec²
  65. extruder.hotend.max_speed 50 # Maximum speed in mm/s
  66.  
  67. extruder.hotend.step_pin 2.0 # Pin for extruder step signal
  68. extruder.hotend.dir_pin 0.5! # Pin for extruder dir signal ( add '!' to reverse direction )
  69. extruder.hotend.en_pin 0.4 # Pin for extruder enable signal
  70.  
  71. # Extruder offset
  72. #extruder.hotend.x_offset 0 # X offset from origin in mm
  73. #extruder.hotend.y_offset 0 # Y offset from origin in mm
  74. #extruder.hotend.z_offset 0 # Z offset from origin in mm
  75.  
  76. # Firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
  77. extruder.hotend.retract_length 5 # Retract length in mm
  78. extruder.hotend.retract_feedrate 50 # Retract feedrate in mm/sec
  79. extruder.hotend.retract_recover_length 0 # Additional length for recover
  80. extruder.hotend.retract_recover_feedrate 8 # Recover feedrate in mm/sec (should be less than retract feedrate)
  81. extruder.hotend.retract_zlift_length 0 # Z-lift on retract in mm, 0 disables
  82. extruder.hotend.retract_zlift_feedrate 6000 # Z-lift feedrate in mm/min (Note mm/min NOT mm/sec)
  83.  
  84. delta_current 1.5 # First extruder stepper motor current
  85.  
  86. # Second extruder module configuration
  87. #extruder.hotend2.enable false # Whether to activate the extruder module at all. All configuration is ignored if false
  88. #extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper
  89. #extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  90. #extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  91. #extruder.hotend2.max_speed 50 # mm/s
  92.  
  93. #extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
  94. #extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal ( add '!' to reverse direction )
  95. #extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
  96.  
  97. #extruder.hotend2.x_offset 0 # x offset from origin in mm
  98. #extruder.hotend2.y_offset 25.0 # y offset from origin in mm
  99. #extruder.hotend2.z_offset 0 # z offset from origin in mm
  100.  
  101. #epsilon_current 1.5 # Second extruder stepper motor current
  102.  
  103. ## Laser module configuration
  104. # See http://smoothieware.org/laser
  105. laser_module_enable false # Whether to activate the laser module at all
  106. #laser_module_pwm_pin 2.5 # This pin will be PWMed to control the laser.
  107. # Only pins 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 1.18, 1.20, 1.21, 1.23, 1.24, 1.26, 3.25 and 3.26
  108. # can be used since laser requires hardware PWM, see http://smoothieware.org/pinout
  109. #laser_module_ttl_pin 1.30 # This pin turns on when the laser turns on, and off when the laser turns off.
  110. #laser_module_maximum_power 1.0 # This is the maximum duty cycle that will be applied to the laser
  111. #laser_module_minimum_power 0.0 # This is a value just below the minimum duty cycle that keeps the laser
  112. # active without actually burning.
  113. #laser_module_default_power 0.8 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
  114. # the maximum and minimum power levels specified above
  115. #laser_module_pwm_period 20 # This sets the pwm frequency as the period in microseconds
  116.  
  117. ## Temperature control configuration
  118. # See http://smoothieware.org/temperaturecontrol
  119.  
  120. # First hotend configuration
  121. temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all.
  122. temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
  123. temperature_control.hotend.heater_pin 2.5 # Pin that controls the heater, set to nc if a readonly thermistor is being defined
  124. temperature_control.hotend.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#toc5
  125. temperature_control.hotend.beta 3950 # Or set the beta value
  126. temperature_control.hotend.set_m_code 104 # M-code to set the temperature for this module
  127. temperature_control.hotend.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  128. temperature_control.hotend.designator H # Designator letter for this module
  129. temperature_control.hotend.max_temp 270 # Set maximum temperature - Will prevent heating above 300 by default
  130. temperature_control.hotend.min_temp 5 # Set minimum temperature - Will prevent heating below if set
  131.  
  132. # Safety control is enabled by default and can be overidden here, the values show the defaults
  133. # See http://smoothieware.org/temperaturecontrol#runaway
  134. temperature_control.hotend.runaway_heating_timeout 900 # How long it can take to heat up, max is 2040 seconds.
  135. temperature_control.hotend.runaway_cooling_timeout 0 # How long it can take to cool down if temp is set lower, max is 2040 seconds
  136. temperature_control.hotend.runaway_range 20 # How far from the set temperature it can wander, max setting is 63°C
  137.  
  138. # PID configuration
  139. # See http://smoothieware.org/temperaturecontrol#pid
  140. temperature_control.hotend.p_factor 31.4 # P ( proportional ) factor
  141. temperature_control.hotend.i_factor 2.072 # I ( integral ) factor
  142. temperature_control.hotend.d_factor 119 # D ( derivative ) factor
  143.  
  144. #temperature_control.hotend.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  145.  
  146. temperature_control.bed.enable true # Whether to activate this ( "hotend" ) module at all.
  147. temperature_control.bed.thermistor_pin 0.24 # Pin for the thermistor to read
  148. temperature_control.bed.heater_pin 2.7 # Pin that controls the heater
  149. temperature_control.bed.thermistor Honeywell100K # See http://smoothieware.org/temperaturecontrol#thermistor
  150. temperature_control.bed.beta 3950 # Or set the beta value
  151. temperature_control.bed.set_m_code 140 # M-code to set the temperature for this module
  152. temperature_control.bed.set_and_wait_m_code 190 # M-code to set-and-wait for this module
  153. temperature_control.bed.designator B # Designator letter for this module
  154.  
  155. temperature_control.bed.p_factor 260.1 # P ( proportional ) factor
  156. temperature_control.bed.i_factor 15.624 # I ( integral ) factor
  157. temperature_control.bed.d_factor 1083 # D ( derivative ) factor
  158.  
  159. temperature_control.bed.max_temp 100 # Set maximum temperature - Will prevent heating above 300 by default
  160. temperature_control.bed.min_temp 5 # Set minimum temperature - Will prevent heating below if set
  161.  
  162. temperature_control.bed.runaway_heating_timeout 2040 # How long it can take to heat up, max is 2040 seconds.
  163. temperature_control.bed.runaway_cooling_timeout 0 # How long it can take to cool down if temp is set lower, max is 2040 seconds
  164. temperature_control.bed.runaway_range 20 # How far from the set temperature it can wander, max setting is 63°C
  165.  
  166. # Second hotend configuration
  167. #temperature_control.hotend2.enable false # Whether to activate this ( "hotend" ) module at all.
  168. #temperature_control.hotend2.thermistor_pin 0.25 # Pin for the thermistor to read
  169. #temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater
  170. #temperature_control.hotend2.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#thermistor
  171. #temperature_control.hotend2.beta 4066 # or set the beta value
  172. #temperature_control.hotend2.set_m_code 104 # M-code to set the temperature for this module
  173. #temperature_control.hotend2.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  174. #temperature_control.hotend2.designator H2 # Designator letter for this module
  175.  
  176. #temperature_control.hotend2.p_factor 13.7 # P ( proportional ) factor
  177. #temperature_control.hotend2.i_factor 0.097 # I ( integral ) factor
  178. #temperature_control.hotend2.d_factor 24 # D ( derivative ) factor
  179.  
  180. #temperature_control.hotend2.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  181.  
  182. # Bang-bang ( simplified ) control
  183. # See http://smoothieware.org/temperaturecontrol#bang-bang
  184. #temperature_control.bed.bang_bang false # Set to true to use bang bang control rather than PID
  185. #temperature_control.bed.hysteresis 2.0 # Set to the temperature in degrees C to use as hysteresis
  186.  
  187. ## Switch modules
  188. # See http://smoothieware.org/switch
  189.  
  190. # Switch module for fan control
  191. switch.fan.enable true # Enable this module
  192. switch.fan.input_on_command M106 # Command that will turn this switch on
  193. switch.fan.input_off_command M107 # Command that will turn this switch off
  194. switch.fan.output_pin 2.4 # Pin this module controls
  195. switch.fan.output_type pwm # PWM output settable with S parameter in the input_on_comand
  196. switch.fan.max_pwm 255 # Set max pwm for the pin default is 255
  197.  
  198. #switch.misc.enable false # Enable this module
  199. #switch.misc.input_on_command M42 # Command that will turn this switch on
  200. #switch.misc.input_off_command M43 # Command that will turn this switch off
  201. #switch.misc.output_pin 2.4 # Pin this module controls
  202. #switch.misc.output_type digital # Digital means this is just an on or off pin
  203.  
  204. ## Temperatureswitch
  205. # See http://smoothieware.org/temperatureswitch
  206. # Automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
  207. # Useful to turn on a fan or water pump to cool the hotend
  208. #temperatureswitch.hotend.enable false #
  209. #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
  210. #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch
  211. #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch
  212. #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
  213. #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
  214.  
  215. ## Endstops
  216. # See http://smoothieware.org/endstops
  217. endstops_enable true # The endstop module is enabled by default and can be disabled here
  218.  
  219. corexy_homing true # Set to true if homing on a hbot or corexy
  220.  
  221. alpha_min_endstop 1.24^! # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  222. #alpha_max_endstop 1.25^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  223. alpha_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  224. alpha_min 0 # This gets loaded as the current position after homing when home_to_min is set
  225. alpha_max 195 # This gets loaded as the current position after homing when home_to_max is set
  226.  
  227. #beta_min_endstop 1.26^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  228. beta_max_endstop 1.27^! # Pin to read max endstop, uncomment this and comment the above if using max endstops
  229. beta_homing_direction home_to_max # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  230. beta_min 0 # This gets loaded as the current position after homing when home_to_min is set
  231. beta_max 190 # This gets loaded as the current position after homing when home_to_max is set
  232.  
  233. gamma_min_endstop 1.29^! # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  234. #gamma_max_endstop 1.28^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  235. gamma_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  236. gamma_min 0 # This gets loaded as the current position after homing when home_to_min is set
  237. gamma_max 225 # This gets loaded as the current position after homing when home_to_max is set
  238.  
  239. alpha_max_travel 195 # Max travel in mm for alpha/X axis when homing
  240. beta_max_travel 190 # Max travel in mm for beta/Y axis when homing
  241. gamma_max_travel 225 # Max travel in mm for gamma/Z axis when homing
  242.  
  243. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered
  244. #alpha_limit_enable false # Set to true to enable X min and max limit switches
  245. #beta_limit_enable false # Set to true to enable Y min and max limit switches
  246. #gamma_limit_enable false # Set to true to enable Z min and max limit switches
  247.  
  248. # Endstops home at their fast feedrate first, then once the endstop is found they home again at their slow feedrate for accuracy
  249. alpha_fast_homing_rate_mm_s 50 # Alpha/X fast homing feedrate in mm/second
  250. alpha_slow_homing_rate_mm_s 25 # Alpha/X slow homing feedrate in mm/second
  251. beta_fast_homing_rate_mm_s 50 # Beta/Y fast homing feedrate in mm/second
  252. beta_slow_homing_rate_mm_s 25 # Beta/Y slow homing feedrate in mm/second
  253. gamma_fast_homing_rate_mm_s 4 # Gamma/Z fast homing feedrate in mm/second
  254. gamma_slow_homing_rate_mm_s 2 # Gamma/Z slow homing feedrate in mm/second
  255.  
  256. alpha_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for alpha/X
  257. beta_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for beta/Y
  258. gamma_homing_retract_mm 1 # Distance to retract from the endstop after it is hit for gamma/Z
  259.  
  260. # Optional order in which axis will home, default is they all home at the same time,
  261. # If this is set it will force each axis to home one at a time in the specified order
  262. homing_order XYZ # X axis followed by Y then Z last
  263. #move_to_origin_after_home false # Move XY to 0,0 after homing
  264. endstop_debounce_count 100 # Uncomment if you get noise on your endstops, default is 100
  265. endstop_debounce_ms 10 # Uncomment if you get noise on your endstops, default is 1 millisecond debounce
  266. #home_z_first true # Uncomment and set to true to home the Z first, otherwise Z homes after XY
  267.  
  268. # End of endstop config
  269. # Delete the above endstop section and uncomment next line and copy and edit Snippets/abc-endstop.config file to enable endstops for ABC axis
  270. #include abc-endstop.config
  271.  
  272. ## Z-probe
  273. # See http://smoothieware.org/zprobe
  274. #zprobe.enable false # Set to true to enable a zprobe
  275. #zprobe.probe_pin 1.28!^ # Pin probe is attached to, if NC remove the !
  276. #zprobe.slow_feedrate 5 # Mm/sec probe feed rate
  277. #zprobe.debounce_count 100 # Set if noisy
  278. #zprobe.fast_feedrate 100 # Move feedrate mm/sec
  279. #zprobe.probe_height 5 # How much above bed to start probe
  280. #gamma_min_endstop nc # Normally 1.28. Change to nc to prevent conflict,
  281.  
  282. # Levelling strategy
  283. # Example for 3-point levelling strategy, see wiki documentation for other strategies
  284. #leveling-strategy.three-point-leveling.enable true # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
  285. #leveling-strategy.three-point-leveling.point1 100.0,0.0 # the first probe point (x,y) optional may be defined with M557
  286. #leveling-strategy.three-point-leveling.point2 200.0,200.0 # the second probe point (x,y)
  287. #leveling-strategy.three-point-leveling.point3 0.0,200.0 # the third probe point (x,y)
  288. #leveling-strategy.three-point-leveling.home_first true # home the XY axis before probing
  289. #leveling-strategy.three-point-leveling.tolerance 0.03 # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
  290. #leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset
  291. #leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false
  292.  
  293. ## Panel
  294. # See http://smoothieware.org/panel
  295. # Please find your panel on the wiki and copy/paste the right configuration here
  296. panel.enable true # Set to true to enable the panel code
  297.  
  298. # Example for reprap discount GLCD
  299. # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
  300. # +5v is EXP1 pin 10, Gnd is EXP1 pin 9
  301. panel.lcd reprap_discount_glcd # set type of panel
  302. panel.spi_channel 0 # set spi channel to use P0_18,P0_15 MOSI,SCLK
  303. panel.spi_cs_pin 0.16 # set spi chip select
  304. panel.encoder_a_pin 3.26^ # encoder pin
  305. panel.encoder_b_pin 3.25^ # encoder pin
  306. panel.click_button_pin 2.11!^ # click button
  307. panel.encoder_resolution 2 # override number of clicks to move 1 item (default is 4)
  308. #panel.button_pause_pin 1.22^ # kill/pause set one of these for the auxilliary button on viki2
  309. #panel.back_button_pin 1.22!^ # back button recommended to use this on EXP1
  310. panel.buzz_pin 1.30 # pin for buzzer on EXP2
  311.  
  312. panel.external_sd true # set to true if there is an extrernal sdcard on the panel
  313. panel.external_sd.spi_channel 0 # set spi channel the sdcard is on
  314. panel.external_sd.spi_cs_pin 1.23 # set spi chip select for the sdcard
  315. panel.external_sd.sdcd_pin 1.31!^ # sd detect signal (set to nc if no sdcard detect)
  316. panel.menu_offset 1 # some panels will need 1 here
  317.  
  318. panel.alpha_jog_feedrate 6000 # X jogging feedrate in mm/min
  319. panel.beta_jog_feedrate 6000 # Y jogging feedrate in mm/min
  320. panel.gamma_jog_feedrate 200 # Z jogging feedrate in mm/min
  321.  
  322. panel.hotend_temperature 185 # Temp to set hotend when preheat is selected
  323. panel.bed_temperature 60 # Temp to set bed when preheat is selected
  324.  
  325. ## Custom menus : Example of a custom menu entry, which will show up in the Custom entry.
  326. # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
  327. #custom_menu.power_on.enable false #
  328. #custom_menu.power_on.name Power_on #
  329. #custom_menu.power_on.command M80 #
  330.  
  331. #custom_menu.power_off.enable false #
  332. #custom_menu.power_off.name Power_off #
  333. #custom_menu.power_off.command M81 #
  334.  
  335.  
  336. ## Network settings
  337. # See http://smoothieware.org/network
  338. network.enable false # Enable the ethernet network services
  339. network.webserver.enable true # Enable the webserver
  340. network.telnet.enable true # Enable the telnet server
  341. network.ip_address auto # Use dhcp to get ip address
  342. # Uncomment the 3 below to manually setup ip address
  343. #network.ip_address 192.168.3.222 # The IP address
  344. #network.ip_mask 255.255.255.0 # The ip mask
  345. #network.ip_gateway 192.168.3.1 # The gateway address
  346. #network.mac_override xx.xx.xx.xx.xx.xx # Override the mac address, only do this if you have a conflict
  347.  
  348. ## System configuration
  349. # Serial communications configuration ( baud rate defaults to 9600 if undefined )
  350. # For communication over the UART port, *not* the USB/Serial port
  351. uart0.baud_rate 115200 # Baud rate for the default hardware ( UART ) serial port
  352.  
  353. second_usb_serial_enable false # This enables a second USB serial port
  354. #leds_disable true # Disable using leds after config loaded
  355. #play_led_disable true # Disable the play led
  356.  
  357. # Kill button maybe assigned to a different pin, set to the onboard pin by default
  358. # See http://smoothieware.org/killbutton
  359. kill_button_enable true # Set to true to enable a kill button
  360. kill_button_pin 2.12 # Kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
  361.  
  362. #msd_disable false # Disable the MSD (USB SDCARD), see http://smoothieware.org/troubleshooting#disable-msd
  363. #dfu_enable false # For linux developers, set to true to enable DFU
  364.  
  365. # Only needed on a smoothieboard
  366. # See http://smoothieware.org/currentcontrol
  367. #currentcontrol_module_enable true # Control stepper motor current via the configuration file
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!