Touch Sonoff NETPIE

#include <ESP8266WiFi.h>          //https://github.com/esp8266/Arduino
#include <ESP8266WebServer.h>
#include <MicroGear.h>                    // include a NETPIE library

//NETPIE
#define APPID "Your application ID"
#define KEY "Your device key"
#define SECRET "Your device secret key"
#define ALIAS "name to make you remember"

const char* ssid = "your wifi network name";
const char* password = "your wifi password";

//GPIO Pin definitions
#define WiFiLED   13
#define TouchLED  12 //Also operates Relay coil
#define TouchInput 0

//Only output info to serial if this is HIGH
#define fDebug true

//Set our inital states and values
boolean ledState = false;
boolean lastButtonState = false;
boolean buttonState = false;
unsigned long lastDebounceTime = 0;
// the last time the output pin was toggled
unsigned long debounceDelay = 50;
// the debounce time; increase if the output flickers
int reading = digitalRead(TouchInput);

const char*             LIGHT_ON                  = "1";
const char*             LIGHT_OFF                 = "0";
bool toPublishSWState;

WiFiClient client;                        // declare a  wificlient
MicroGear microgear(client);              // declare microgear object

void stateChange(int relayID, int type, int state) {
    Serial.print("relay ");
    Serial.print(relayID);
    Serial.print(" --> ");
    Serial.println(state?"ON":"OFF");
    if (relayID==1) toPublishSWState = true;
}

void onMsghandler(char *topic, uint8_t* msg, unsigned int msglen) {
    char m = *(char *)msg;
    msg[msglen] = '\0';
    Serial.print("incoming message: ");
    Serial.print((char *)topic);
    Serial.print(" --> ");
    Serial.println((char*)msg);

    if (msg[0]=='1' && msg[1]=='0')
      {
        buttonState = reading;

      ledState = false;
      // set the LED:
      setLightState();
      microgear.publish("/state",ledState);
      }
    if (msg[0]=='1' && msg[1]=='1')
      {
        buttonState = reading;

      ledState = true;
      // set the LED:
      setLightState();
      microgear.publish("/state",ledState);
      }
    if (msg[0]=='1' && msg[1]=='?')
      {
        toPublishSWState = true;
      }
}

void onConnected(char *attribute, uint8_t* msg, unsigned int msglen) {
    Serial.println("Connected to NETPIE...");
    microgear.setAlias(ALIAS);
    toPublishSWState = true;
}

void initWiFi(){
    if (WiFi.begin(ssid, password)) {
        while (WiFi.status() != WL_CONNECTED) {
            delay(500);
            Serial.print(".");
        }
    }
    Serial.println("WiFi connected");
    Serial.println("IP address: ");
    Serial.println(WiFi.localIP());
}

void setup() {

  //Setup our GPIO pins for input/output as needed
  pinMode(WiFiLED, OUTPUT);
  pinMode(TouchLED, OUTPUT);
  pinMode(TouchInput, INPUT);

  //Turn those LEDS's off :)
  digitalWrite(WiFiLED, HIGH);
  digitalWrite(TouchLED, ledState);

  initWiFi();

  // add event listeners
  microgear.on(MESSAGE, onMsghandler);    // when new message arrives
  microgear.on(CONNECTED, onConnected);   // when connected to NETPIE
  microgear.init(KEY, SECRET);            // initial a micrigear variable
  microgear.connect(APPID);               // let a device connects to NETPIE

}
// function called to publish the state of the light (on/off)
void publishLightState() {
  if (fDebug) {
    Serial.println("PublishLightState Called");
    Serial.print("Light State: ");
    Serial.println(ledState);
  }
  if (ledState == HIGH) {
    if (fDebug) {
      Serial.print("Light state high ");
      Serial.println(ledState);
    }
//    client.publish(MQTT_LIGHT_STATE_TOPIC, LIGHT_ON, true);
  } else {
    if (fDebug) {
      Serial.print("Light state low ");
      Serial.println(ledState);
    }
//    client.publish(MQTT_LIGHT_STATE_TOPIC, LIGHT_OFF, true);
  }
}

// function called to turn on/off the light
void setLightState() {
  //Set our light state, ie turn the touch LED on/off
  //which is the same GPIO pin as the relay.
  digitalWrite(TouchLED, ledState);
  //Feedback to HA our new state
  publishLightState();
}


void loop() {
  /**
   * THis section is to let the NETPIE control the system
   */

  if(WiFi.status()!=WL_CONNECTED){
        WiFi.disconnect();
        initWiFi();
    } else {
        if (microgear.connected()) {

          // to check if switch 1 need to update its status
            if (toPublishSWState) {

                // check the status and send message to the topic “/state”
//                if (ledState) microgear.publish("/state","1");
//                if (!ledState) microgear.publish("/state","0");
//
                microgear.publish("/state",ledState);
                toPublishSWState = false;
            }
            microgear.loop();
        }
        else {
            microgear.connect(APPID);
            delay(500);
        }
    }

  /**
   * This section is the physical touch condition
   */
  //Get the current button state
  reading = digitalRead(TouchInput);
  //De-bounce the button
  if (reading != lastButtonState) {
    lastDebounceTime = millis();
  }
  if ((millis() - lastDebounceTime) > debounceDelay) {
    // whatever the reading is at, it's been there for longer
    // than the debounce delay, so take it as the actual current state:

    // if the button state has changed:
    if (reading != buttonState) {
      buttonState = reading;

      // only toggle the LED if the new button state is HIGH
      if (buttonState == HIGH) {
        ledState = !ledState;
      }
      // set the LED:
      setLightState();
      microgear.publish("/state",ledState);
    }
  }
  // save the reading.  Next time through the loop,
  // it'll be the lastButtonState:
  lastButtonState = reading;
  delay(64);
//  client.loop();
}