F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 0229 [010F]
Jump to BL

NOTICE:  BL2: v2.6(release):3b1fd9bf
NOTICE:  BL2: Built : 07:12:00, Aug 12 2022
NOTICE:  WDT: disabled
NOTICE:  CPU: MT7986 (2000MHz)
NOTICE:  EMI: Using DDR4 settings
NOTICE:  EMI: Detected DRAM size: 1024MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0xc2
NOTICE:  Page size 4096, Block size 262144, size 536870912
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 2047 [0x1ffc0000]
NOTICE:  First info table with writecount 1 found in block 1920
NOTICE:  Second info table with writecount 1 found in block 1923
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.6(release):3b1fd9bf
NOTICE:  BL31: Built : 07:12:05, Aug 12 2022


U-Boot 2022.01-rc4 (Aug 12 2022 - 07:10:55 +0000)

CPU:   MediaTek MT7986
Model: ZYXEL EX5601-T0
DRAM:  1 GiB

Initializing NMBM ...
spi-nand: spi_nand spi_nand@1: Macronix SPI NAND was found.
spi-nand: spi_nand spi_nand@1: 512 MiB, block size: 256 KiB, page size: 4096, OOB size: 128
Could not find a valid device for nmbm0
Signature found at block 2047 [0x1ffc0000]
First info table with writecount 1 found in block 1920
Second info table with writecount 1 found in block 1923
NMBM has been successfully attached

MMC:   mmc@11230000: 0
Loading Environment from MTD... OK
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   eth0: ethernet@15100000
Reading 262144 byte(s) at offset 0x00000000
## Booting kernel from Legacy Image at 46000000 ...
   Image Name:   zld-2.3 08/12/2022 07:11:53
   Image Type:   AArch64 U-Boot Standalone Program (gzip compressed)
   Data Size:    22205 Bytes = 21.7 KiB
   Load Address: 41e00200
   Entry Point:  41e003f4
   Verifying Checksum ... OK
   Uncompressing Standalone Program


ZYXEL zloader v2.3.9 (08/12/2022 - 07:11:53)
ubi0: attaching mtd7
ubi0: scanning is finished
ubi0: attached mtd7 (name "ubi", size 64 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/1, WL threshold: 4096, image sequence number: 1661837921
ubi0: available PEBs: 1, total reserved PEBs: 255, PEBs reserved for bad PEB handling: 38
Reading from volume 'zyfwinfo' to 0x7f7feee0, size 0x100 ... OK
ubi0: detaching mtd7
ubi0: mtd7 is detached
ubi0: attaching mtd8
ubi0: scanning is finished
ubi0: attached mtd8 (name "ubi2", size 64 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 0
ubi0: available PEBs: 214, total reserved PEBs: 42, PEBs reserved for bad PEB handling: 38
Reading from volume 'zyfwinfo' to 0x7f7fefe0, size 0x100 ... *** Cannot find volume 'zyfwinfo' ***
ubi0: detaching mtd8
ubi0: mtd8 is detached
Cannot get zyfwinfo from ubi2
Current bootflag is 0
BOARD_DETECT_BY_GPIO=>result=0
ubi0: attaching mtd7
ubi0: scanning is finished
ubi0: attached mtd7 (name "ubi", size 64 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/1, WL threshold: 4096, image sequence number: 1661837921
ubi0: available PEBs: 1, total reserved PEBs: 255, PEBs reserved for bad PEB handling: 38
Reading from volume 'zyfwinfo' to 0x7fb35590, size 0x100 ... OK
ubi0: detaching mtd7
ubi0: mtd7 is detached
Multiboot clinent version: 2.7

Hit any key to stop autoboot:  5
ZHAL> ATGU




ZYXEL zloader v2.3.9 (08/12/2022 - 07:11:53)
ubi0: attaching mtd7
ubi0: scanning is finished
ubi0: attached mtd7 (name "ubi", size 64 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/1, WL threshold: 4096, image sequence number: 1661837921
ubi0: available PEBs: 1, total reserved PEBs: 255, PEBs reserved for bad PEB handling: 38
Reading from volume 'zyfwinfo' to 0x7f7feea0, size 0x100 ... OK
ubi0: detaching mtd7
ubi0: mtd7 is detached
ubi0: attaching mtd8
ubi0: scanning is finished
ubi0: attached mtd8 (name "ubi2", size 64 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 0
ubi0: available PEBs: 214, total reserved PEBs: 42, PEBs reserved for bad PEB handling: 38
Reading from volume 'zyfwinfo' to 0x7f7fefa0, size 0x100 ... *** Cannot find volume 'zyfwinfo' ***
ubi0: detaching mtd8
ubi0: mtd8 is detached
Cannot get zyfwinfo from ubi2
Current bootflag is 0
BOARD_DETECT_BY_GPIO=>result=0
ubi0: attaching mtd7
ubi0: scanning is finished
ubi0: attached mtd7 (name "ubi", size 64 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/1, WL threshold: 4096, image sequence number: 1661837921
ubi0: available PEBs: 1, total reserved PEBs: 255, PEBs reserved for bad PEB handling: 38
Reading from volume 'zyfwinfo' to 0x7fb35590, size 0x100 ... OK
ubi0: detaching mtd7
ubi0: mtd7 is detached
Multiboot clinent version: 2.7

Hit any key to stop autoboot:  5
ZHAL> ATGU


MT7986> tftpboot u-boot.bin
Using ethernet@15100000 device
TFTP from server 192.168.1.110; our IP address is 192.168.1.1
Filename 'u-boot.bin'.
Load address: 0x46000000
Loading: #################################################################
         ####
         7.5 MiB/s
done
Bytes transferred = 1008744 (f6468 hex)
MT7986> go 0x46000000
## Starting application at 0x46000000 ...▒▒

U-Boot 2023.07.02-OpenWrt-r23815-1e7cb4de5e (Aug 26 2023 - 22:02:45 +0000)

CPU:   MediaTek MT7986
Model: Zyxel EX5601-T0 ubootmod
DRAM:  1 GiB
Core:  36 devices, 20 uclasses, devicetree: embed
Loading Environment from UBI... spi-nand: spi_nand spi_nand@0: Macronix SPI NAND was found.
spi-nand: spi_nand spi_nand@0: 512 MiB, block size: 256 KiB, page size: 4096, OOB size: 128
ubi0 error: scan_peb: bad image sequence number -703548806 in PEB 512, expected 1661837921
Erase counter header dump:
        magic          0x55424923
        version        1
        ec             2
        vid_hdr_offset 4096
        data_offset    8192
        image_seq      -703548806
        hdr_crc        0xdc36df6c
erase counter header hexdump:
00000000: 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 02 00 00 10 00 00 00 20 00 d6 10 b2 7a 00 00 00 00  UBI#.................. ....z....
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 dc 36 df 6c  .............................6.l
ubi0 error: ubi_attach_mtd_dev: failed to attach mtd6, error -22
UBI error: cannot attach mtd6
UBI error: cannot initialize UBI, error -22
UBI init error 22
Please check, if the correct MTD partition is used (size big enough?)

** Cannot find mtd partition "ubi"
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
reset button found
Loading Environment from UBI... ubi0 error: scan_peb: bad image sequence number -703548806 in PEB 512, expected 1661837921
Erase counter header dump:
        magic          0x55424923
        version        1
        ec             2
        vid_hdr_offset 4096
        data_offset    8192
        image_seq      -703548806
        hdr_crc        0xdc36df6c
erase counter header hexdump:
00000000: 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 02 00 00 10 00 00 00 20 00 d6 10 b2 7a 00 00 00 00  UBI#.................. ....z....
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 dc 36 df 6c  .............................6.l
ubi0 error: ubi_attach_mtd_dev: failed to attach mtd6, error -22
UBI error: cannot attach mtd6
UBI error: cannot initialize UBI, error -22
UBI init error 22
Please check, if the correct MTD partition is used (size big enough?)

** Cannot find mtd partition "ubi"
Net:
Warning: ethernet@15100000 (eth0) using random MAC address - 4a:0f:05:54:aa:71
eth0: ethernet@15100000
No EFI system partition
No EFI system partition
Failed to persist EFI variables
Reading 131072 byte(s) (32 page(s)) at offset 0x00000000
Error, no UBI device selected!
Error, no UBI device selected!
Error, no UBI device selected!
Error, no UBI device selected!
Saving Environment to UBI... ubi0 error: scan_peb: bad image sequence number -703548806 in PEB 512, expected 1661837921
Erase counter header dump:
        magic          0x55424923
        version        1
        ec             2
        vid_hdr_offset 4096
        data_offset    8192
        image_seq      -703548806
        hdr_crc        0xdc36df6c
erase counter header hexdump:
00000000: 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 02 00 00 10 00 00 00 20 00 d6 10 b2 7a 00 00 00 00  UBI#.................. ....z....
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 dc 36 df 6c  .............................6.l
ubi0 error: ubi_attach_mtd_dev: failed to attach mtd6, error -22
UBI error: cannot attach mtd6
UBI error: cannot initialize UBI, error -22
UBI init error 22
Please check, if the correct MTD partition is used (size big enough?)

** Cannot find mtd partition "ubi"
Failed (1)
Saving Environment to UBI... ubi0 error: scan_peb: bad image sequence number -703548806 in PEB 512, expected 1661837921
Erase counter header dump:
        magic          0x55424923
        version        1
        ec             2
        vid_hdr_offset 4096
        data_offset    8192
        image_seq      -703548806
        hdr_crc        0xdc36df6c
erase counter header hexdump:
00000000: 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 02 00 00 10 00 00 00 20 00 d6 10 b2 7a 00 00 00 00  UBI#.................. ....z....
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 dc 36 df 6c  .............................6.l
ubi0 error: ubi_attach_mtd_dev: failed to attach mtd6, error -22
UBI error: cannot attach mtd6
UBI error: cannot initialize UBI, error -22
UBI init error 22
Please check, if the correct MTD partition is used (size big enough?)

** Cannot find mtd partition "ubi"
Failed (1)
off

        ( ( ( OpenWrt ) ) )       U-Boot 2023.07.02-OpenWrt-r23815-1e7cb4de5e (Aug 26 2023 - 22:02:45 +0000)

      1. Run default boot command.
      2. Boot system via TFTP.
      3. Boot production system from NAND.
      4. Boot recovery system from NAND.
      5. Load production system via TFTP then write to NAND.
      6. Load recovery system via TFTP then write to NAND.
      7. Load BL31+U-Boot FIP via TFTP then write to NAND.
      8. Load BL2 preloader via TFTP then write to NAND.
      9. Reboot.
      a. Reset all settings to factory defaults.
      0. U-Boot console


  Press UP/DOWN to move, ENTER to select, ESC to quit
EX5601>