Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.1.0-0.deb11.7-amd64] (local build)
- Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: Western Digital Red
- Device Model: WDC WD30EFRX-68AX9N0
- Serial Number: WD-xxxxxxx
- LU WWN Device Id: 5 0014ee 0ae285442
- Firmware Version: 80.00A80
- User Capacity: 3.000.592.982.016 bytes [3,00 TB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Device is: In smartctl database [for details use: -P show]
- ATA Version is: ACS-2 (minor revision not indicated)
- SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
- Local Time is: Sun Jul 2 13:29:43 2023 CEST
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x82) Offline data collection activity
- was completed without error.
- Auto Offline Data Collection: Enabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: (38460) seconds.
- Offline data collection
- capabilities: (0x7b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 386) minutes.
- Conveyance self-test routine
- recommended polling time: ( 5) minutes.
- SCT capabilities: (0x70bd) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 1
- 3 Spin_Up_Time 0x0027 181 177 021 Pre-fail Always - 5950
- 4 Start_Stop_Count 0x0032 071 071 000 Old_age Always - 29118
- 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
- 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
- 9 Power_On_Hours 0x0032 017 017 000 Old_age Always - 60649
- 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
- 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
- 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1306
- 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 163
- 193 Load_Cycle_Count 0x0032 191 191 000 Old_age Always - 28954
- 194 Temperature_Celsius 0x0022 122 109 000 Old_age Always - 28
- 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
- 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
- 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
- 199 UDMA_CRC_Error_Count 0x0032 200 198 000 Old_age Always - 58
- 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
- SMART Error Log Version: 1
- ATA Error Count: 53926 (device log contains only the most recent five errors)
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 53926 occurred at disk power-on lifetime: 60583 hours (2524 days + 7 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 04 61 02 00 00 00 a0 Device Fault; Error: ABRT
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- ef 10 02 00 00 00 a0 08 00:01:14.599 SET FEATURES [Enable SATA feature]
- ec 00 00 00 00 00 a0 08 00:01:14.598 IDENTIFY DEVICE
- ef 03 46 00 00 00 a0 08 00:01:14.598 SET FEATURES [Set transfer mode]
- ef 10 02 00 00 00 a0 08 00:01:14.598 SET FEATURES [Enable SATA feature]
- ec 00 00 00 00 00 a0 08 00:01:14.597 IDENTIFY DEVICE
- Error 53925 occurred at disk power-on lifetime: 60583 hours (2524 days + 7 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 04 61 46 00 00 00 a0 Device Fault; Error: ABRT
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- ef 03 46 00 00 00 a0 08 00:01:14.598 SET FEATURES [Set transfer mode]
- ef 10 02 00 00 00 a0 08 00:01:14.598 SET FEATURES [Enable SATA feature]
- ec 00 00 00 00 00 a0 08 00:01:14.597 IDENTIFY DEVICE
- ca 00 08 00 08 00 e0 08 00:01:14.555 WRITE DMA
- ef 10 02 00 00 00 a0 08 00:01:14.555 SET FEATURES [Enable SATA feature]
- Error 53924 occurred at disk power-on lifetime: 60583 hours (2524 days + 7 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 04 61 02 00 00 00 a0 Device Fault; Error: ABRT
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- ef 10 02 00 00 00 a0 08 00:01:14.598 SET FEATURES [Enable SATA feature]
- ec 00 00 00 00 00 a0 08 00:01:14.597 IDENTIFY DEVICE
- ca 00 08 00 08 00 e0 08 00:01:14.555 WRITE DMA
- ef 10 02 00 00 00 a0 08 00:01:14.555 SET FEATURES [Enable SATA feature]
- ec 00 00 00 00 00 a0 08 00:01:14.554 IDENTIFY DEVICE
- Error 53923 occurred at disk power-on lifetime: 60583 hours (2524 days + 7 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 04 61 08 00 08 00 e0 Device Fault; Error: ABRT at LBA = 0x00000800 = 2048
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- ca 00 08 00 08 00 e0 08 00:01:14.555 WRITE DMA
- ef 10 02 00 00 00 a0 08 00:01:14.555 SET FEATURES [Enable SATA feature]
- ec 00 00 00 00 00 a0 08 00:01:14.554 IDENTIFY DEVICE
- ef 03 46 00 00 00 a0 08 00:01:14.554 SET FEATURES [Set transfer mode]
- ef 10 02 00 00 00 a0 08 00:01:14.554 SET FEATURES [Enable SATA feature]
- Error 53922 occurred at disk power-on lifetime: 60583 hours (2524 days + 7 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 04 61 02 00 00 00 a0 Device Fault; Error: ABRT
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- ef 10 02 00 00 00 a0 08 00:01:14.555 SET FEATURES [Enable SATA feature]
- ec 00 00 00 00 00 a0 08 00:01:14.554 IDENTIFY DEVICE
- ef 03 46 00 00 00 a0 08 00:01:14.554 SET FEATURES [Set transfer mode]
- ef 10 02 00 00 00 a0 08 00:01:14.554 SET FEATURES [Enable SATA feature]
- ec 00 00 00 00 00 a0 08 00:01:14.553 IDENTIFY DEVICE
- SMART Self-test log structure revision number 1
- No self-tests have been logged. [To run self-tests, use: smartctl -t]
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement