Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.11.0-26-generic] (local build)
- Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: Toshiba 3.5" DT01ACA... Desktop HDD
- Device Model: TOSHIBA DT01ACA100
- Serial Number: Y2IMVWZPS
- LU WWN Device Id: 5 000039 ff2c9080a
- Firmware Version: MS2OA750
- User Capacity: 1,000,204,886,016 bytes [1.00 TB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Rotation Rate: 7200 rpm
- Form Factor: 3.5 inches
- Device is: In smartctl database 7.3/5528
- ATA Version is: ATA8-ACS T13/1699-D revision 4
- SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
- Local Time is: Tue Jun 17 08:46:39 2025 CEST
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- AAM feature is: Unavailable
- APM feature is: Disabled
- Rd look-ahead is: Enabled
- Write cache is: Enabled
- DSN feature is: Unavailable
- ATA Security is: Disabled, NOT FROZEN [SEC1]
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x80) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Enabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 7653) seconds.
- Offline data collection
- capabilities: (0x5b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- No Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 1) minutes.
- Extended self-test routine
- recommended polling time: ( 128) minutes.
- SCT capabilities: (0x003d) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
- 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0
- 2 Throughput_Performance P-S--- 100 100 054 - 0
- 3 Spin_Up_Time POS--- 100 100 024 - 0
- 4 Start_Stop_Count -O--C- 100 100 000 - 3
- 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
- 7 Seek_Error_Rate PO-R-- 100 100 067 - 0
- 8 Seek_Time_Performance P-S--- 100 100 020 - 0
- 9 Power_On_Hours -O--C- 100 100 000 - 0
- 10 Spin_Retry_Count PO--C- 100 100 060 - 0
- 12 Power_Cycle_Count -O--CK 100 100 000 - 3
- 192 Power-Off_Retract_Count -O--CK 100 100 000 - 3
- 193 Load_Cycle_Count -O--C- 100 100 000 - 3
- 194 Temperature_Celsius -O---- 193 193 000 - 31 (Min/Max 25/34)
- 196 Reallocated_Event_Count -O--CK 100 100 000 - 0
- 197 Current_Pending_Sector -O---K 100 100 000 - 0
- 198 Offline_Uncorrectable ---R-- 100 100 000 - 0
- 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0
- ||||||_ K auto-keep
- |||||__ C event count
- ||||___ R error rate
- |||____ S speed/performance
- ||_____ O updated online
- |______ P prefailure warning
- General Purpose Log Directory Version 1
- SMART Log Directory Version 1 [multi-sector log support]
- Address Access R/W Size Description
- 0x00 GPL,SL R/O 1 Log Directory
- 0x01 SL R/O 1 Summary SMART error log
- 0x03 GPL R/O 1 Ext. Comprehensive SMART error log
- 0x04 GPL R/O 7 Device Statistics log
- 0x06 SL R/O 1 SMART self-test log
- 0x07 GPL R/O 1 Extended self-test log
- 0x08 GPL R/O 2 Power Conditions log
- 0x09 SL R/W 1 Selective self-test log
- 0x10 GPL R/O 1 NCQ Command Error log
- 0x11 GPL R/O 1 SATA Phy Event Counters log
- 0x20 GPL R/O 1 Streaming performance log
- 0x21 GPL R/O 1 Write stream error log
- 0x22 GPL R/O 1 Read stream error log
- 0x80-0x9f GPL,SL R/W 16 Host vendor specific log
- 0xe0 GPL,SL R/W 1 SCT Command/Status
- 0xe1 GPL,SL R/W 1 SCT Data Transfer
- SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
- Device Error Count: 65535 (device log contains only the most recent 4 errors)
- CR = Command Register
- FEATR = Features Register
- COUNT = Count (was: Sector Count) Register
- LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
- LH = LBA High (was: Cylinder High) Register ] LBA
- LM = LBA Mid (was: Cylinder Low) Register ] Register
- LL = LBA Low (was: Sector Number) Register ]
- DV = Device (was: Device/Head) Register
- DC = Device Control Register
- ER = Error register
- ST = Status register
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 65535 [3] occurred at disk power-on lifetime: 19269 hours (802 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 06 00 00 01 ae 8e b8 01 00 Error: UNC at LBA = 0x01ae8eb8 = 28217016
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 08 00 18 00 00 01 ae 8e b6 40 00 2d+04:17:19.604 READ FPDMA QUEUED
- ef 00 10 00 02 00 00 00 00 00 00 a0 00 2d+04:17:19.603 SET FEATURES [Enable SATA feature]
- 27 00 00 00 00 00 00 00 00 00 00 e0 00 2d+04:17:19.603 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
- ec 00 00 00 00 00 00 00 00 00 00 a0 00 2d+04:17:19.603 IDENTIFY DEVICE
- ef 00 03 00 46 00 00 00 00 00 00 a0 00 2d+04:17:19.603 SET FEATURES [Set transfer mode]
- Error 65534 [2] occurred at disk power-on lifetime: 19269 hours (802 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 06 00 00 01 ae 8e b8 01 00 Error: UNC at LBA = 0x01ae8eb8 = 28217016
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 08 00 b0 00 00 01 ae 8e b6 40 00 2d+04:17:19.429 READ FPDMA QUEUED
- ef 00 10 00 02 00 00 00 00 00 00 a0 00 2d+04:17:19.428 SET FEATURES [Enable SATA feature]
- 27 00 00 00 00 00 00 00 00 00 00 e0 00 2d+04:17:19.428 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
- ec 00 00 00 00 00 00 00 00 00 00 a0 00 2d+04:17:19.428 IDENTIFY DEVICE
- ef 00 03 00 46 00 00 00 00 00 00 a0 00 2d+04:17:19.427 SET FEATURES [Set transfer mode]
- Error 65533 [1] occurred at disk power-on lifetime: 19269 hours (802 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 06 00 00 01 ae 8e b8 01 00 Error: UNC at LBA = 0x01ae8eb8 = 28217016
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 08 00 c0 00 00 01 ae 8e b6 40 00 2d+04:17:19.261 READ FPDMA QUEUED
- ef 00 10 00 02 00 00 00 00 00 00 a0 00 2d+04:17:19.261 SET FEATURES [Enable SATA feature]
- 27 00 00 00 00 00 00 00 00 00 00 e0 00 2d+04:17:19.261 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
- ec 00 00 00 00 00 00 00 00 00 00 a0 00 2d+04:17:19.260 IDENTIFY DEVICE
- ef 00 03 00 46 00 00 00 00 00 00 a0 00 2d+04:17:19.260 SET FEATURES [Set transfer mode]
- Error 65532 [0] occurred at disk power-on lifetime: 19269 hours (802 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 06 00 00 01 ae 8e b8 01 00 Error: UNC at LBA = 0x01ae8eb8 = 28217016
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 08 00 10 00 00 01 ae 8e b6 40 00 2d+04:17:19.110 READ FPDMA QUEUED
- 60 00 08 00 08 00 00 00 ec bf c6 40 00 2d+04:17:18.640 READ FPDMA QUEUED
- 60 00 08 00 88 00 00 00 eb 96 de 40 00 2d+04:17:18.615 READ FPDMA QUEUED
- 60 00 08 00 80 00 00 00 ec 95 a6 40 00 2d+04:17:18.591 READ FPDMA QUEUED
- 60 00 08 00 00 00 00 00 c6 63 e6 40 00 2d+04:17:18.309 READ FPDMA QUEUED
- SMART Extended Self-test Log Version: 1 (1 sectors)
- Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
- # 1 Short captive Completed without error 00% 15 -
- # 2 Short offline Completed without error 00% 19382 -
- # 3 Short offline Completed without error 00% 5632 -
- # 4 Short offline Completed without error 00% 5629 -
- # 5 Short offline Completed without error 00% 5627 -
- # 6 Short offline Completed without error 00% 3205 -
- # 7 Short offline Completed without error 00% 3202 -
- # 8 Short offline Completed without error 00% 3202 -
- # 9 Short offline Completed without error 00% 3137 -
- #10 Short offline Completed without error 00% 3132 -
- #11 Short offline Completed without error 00% 3108 -
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
- SCT Status Version: 3
- SCT Version (vendor specific): 256 (0x0100)
- Device State: Active (0)
- Current Temperature: 32 Celsius
- Power Cycle Min/Max Temperature: 29/32 Celsius
- Lifetime Min/Max Temperature: 25/34 Celsius
- Under/Over Temperature Limit Count: 0/0
- SCT Temperature History Version: 2
- Temperature Sampling Period: 1 minute
- Temperature Logging Interval: 1 minute
- Min/Max recommended Temperature: 0/60 Celsius
- Min/Max Temperature Limit: -40/70 Celsius
- Temperature History Size (Index): 128 (81)
- Index Estimated Time Temperature Celsius
- 82 2025-06-17 06:39 32 *************
- ... ..( 36 skipped). .. *************
- 119 2025-06-17 07:16 32 *************
- 120 2025-06-17 07:17 33 **************
- 121 2025-06-17 07:18 32 *************
- ... ..( 53 skipped). .. *************
- 47 2025-06-17 08:12 32 *************
- 48 2025-06-17 08:13 33 **************
- ... ..( 12 skipped). .. **************
- 61 2025-06-17 08:26 33 **************
- 62 2025-06-17 08:27 34 ***************
- 63 2025-06-17 08:28 33 **************
- 64 2025-06-17 08:29 ? -
- 65 2025-06-17 08:30 ? -
- 66 2025-06-17 08:31 30 ***********
- 67 2025-06-17 08:32 30 ***********
- 68 2025-06-17 08:33 31 ************
- 69 2025-06-17 08:34 31 ************
- 70 2025-06-17 08:35 32 *************
- 71 2025-06-17 08:36 32 *************
- 72 2025-06-17 08:37 33 **************
- 73 2025-06-17 08:38 33 **************
- 74 2025-06-17 08:39 34 ***************
- 75 2025-06-17 08:40 ? -
- 76 2025-06-17 08:41 29 **********
- 77 2025-06-17 08:42 30 ***********
- 78 2025-06-17 08:43 30 ***********
- 79 2025-06-17 08:44 31 ************
- 80 2025-06-17 08:45 31 ************
- 81 2025-06-17 08:46 31 ************
- SCT Error Recovery Control:
- Read: Disabled
- Write: Disabled
- Device Statistics (GP Log 0x04)
- Page Offset Size Value Flags Description
- 0x01 ===== = = === == General Statistics (rev 1) ==
- 0x01 0x008 4 3 --- Lifetime Power-On Resets
- 0x01 0x010 4 0 --- Power-on Hours
- 0x01 0x018 6 0 --- Logical Sectors Written
- 0x01 0x020 6 0 --- Number of Write Commands
- 0x01 0x028 6 2690 --- Logical Sectors Read
- 0x01 0x030 6 99 --- Number of Read Commands
- 0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
- 0x03 0x008 4 0 --- Spindle Motor Power-on Hours
- 0x03 0x010 4 0 --- Head Flying Hours
- 0x03 0x018 4 3 --- Head Load Events
- 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
- 0x03 0x028 4 0 --- Read Recovery Attempts
- 0x03 0x030 4 0 --- Number of Mechanical Start Failures
- 0x04 ===== = = === == General Errors Statistics (rev 1) ==
- 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
- 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion
- 0x05 ===== = = === == Temperature Statistics (rev 1) ==
- 0x05 0x008 1 32 --- Current Temperature
- 0x05 0x010 1 - N-- Average Short Term Temperature
- 0x05 0x018 1 - N-- Average Long Term Temperature
- 0x05 0x020 1 34 --- Highest Temperature
- 0x05 0x028 1 25 --- Lowest Temperature
- 0x05 0x030 1 - N-- Highest Average Short Term Temperature
- 0x05 0x038 1 - N-- Lowest Average Short Term Temperature
- 0x05 0x040 1 - N-- Highest Average Long Term Temperature
- 0x05 0x048 1 - N-- Lowest Average Long Term Temperature
- 0x05 0x050 4 0 --- Time in Over-Temperature
- 0x05 0x058 1 60 --- Specified Maximum Operating Temperature
- 0x05 0x060 4 0 --- Time in Under-Temperature
- 0x05 0x068 1 0 --- Specified Minimum Operating Temperature
- 0x06 ===== = = === == Transport Statistics (rev 1) ==
- 0x06 0x008 4 2 --- Number of Hardware Resets
- 0x06 0x010 4 0 --- Number of ASR Events
- 0x06 0x018 4 0 --- Number of Interface CRC Errors
- |||_ C monitored condition met
- ||__ D supports DSN
- |___ N normalized value
- SATA Phy Event Counters (GP Log 0x11)
- ID Size Value Description
- 0x0001 2 0 Command failed due to ICRC error
- 0x0002 2 0 R_ERR response for data FIS
- 0x0003 2 0 R_ERR response for device-to-host data FIS
- 0x0004 2 0 R_ERR response for host-to-device data FIS
- 0x0005 2 0 R_ERR response for non-data FIS
- 0x0006 2 0 R_ERR response for device-to-host non-data FIS
- 0x0007 2 0 R_ERR response for host-to-device non-data FIS
- 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
- 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET
- 0x000b 2 0 CRC errors within host-to-device FIS
- 0x000d 2 0 Non-CRC errors within host-to-device FIS
Advertisement
Add Comment
Please, Sign In to add comment