Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- [ 0.000000] Linux version 5.4.121 (xxx
- @notebook) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r12848-86db1f69c4)) #0 SMP Mon May 24 07:09:00 2021
- [ 0.000000] SoC: xRX200 rev 1.1
- [ 0.000000] printk: bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 00019555 (MIPS 34Kc)
- [ 0.000000] MIPS: machine is ZyXEL P-2812HNU-F1
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Detected 1 available secondary CPU(s)
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
- [ 0.000000] On node 0 totalpages: 32768
- [ 0.000000] Normal zone: 256 pages used for memmap
- [ 0.000000] Normal zone: 0 pages reserved
- [ 0.000000] Normal zone: 32768 pages, LIFO batch:7
- [ 0.000000] percpu: Embedded 14 pages/cpu s25680 r8192 d23472 u57344
- [ 0.000000] pcpu-alloc: s25680 r8192 d23472 u57344 alloc=14*4096
- [ 0.000000] pcpu-alloc: [0] 0 [0] 1
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
- [ 0.000000] Kernel command line: console=ttyLTQ0,115200
- [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
- [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
- [ 0.000000] Writing ErrCtl register=00000808
- [ 0.000000] Readback ErrCtl register=00000808
- [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
- [ 0.000000] Memory: 121428K/131072K available (5232K kernel code, 175K rwdata, 1448K rodata, 1256K init, 211K bss, 9644K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] rcu: Hierarchical RCU implementation.
- [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
- [ 0.000000] NR_IRQS: 256
- [ 0.000000] random: get_random_bytes called from start_kernel+0x360/0x540 with crng_init=0
- [ 0.000000] CPU Clock: 500MHz
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
- [ 0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
- [ 0.007907] Calibrating delay loop... 331.77 BogoMIPS (lpj=1658880)
- [ 0.074007] pid_max: default: 32768 minimum: 301
- [ 0.078858] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.086103] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.096645] rcu: Hierarchical SRCU implementation.
- [ 0.101963] smp: Bringing up secondary CPUs ...
- [ 0.107355] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.107368] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
- [ 0.107491] CPU1 revision is: 00019555 (MIPS 34Kc)
- [ 0.166652] Synchronize counters for CPU 1: done.
- [ 0.190968] smp: Brought up 1 node, 2 CPUs
- [ 0.200566] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.210320] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
- [ 0.217229] pinctrl core: initialized pinctrl subsystem
- [ 0.223656] NET: Registered protocol family 16
- [ 0.243200] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
- [ 0.256273] pinctrl-xway 1e100b10.pinmux: Init done
- [ 0.263220] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
- [ 0.275718] PCI host bridge /fpi@10000000/pci@e105400 ranges:
- [ 0.281345] MEM 0x0000000018000000..0x0000000019ffffff
- [ 0.286670] IO 0x000000001ae00000..0x000000001affffff
- [ 0.323400] gpio-stp-xway 1e100bb0.stp: Init done
- [ 0.330443] usbcore: registered new interface driver usbfs
- [ 0.335960] usbcore: registered new interface driver hub
- [ 0.341373] usbcore: registered new device driver usb
- [ 0.347064] PCI host bridge to bus 0000:00
- [ 0.351028] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
- [ 0.358010] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
- [ 0.364891] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
- [ 0.371788] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.382676] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
- [ 0.389278] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
- [ 0.401095] clocksource: Switched to clocksource MIPS
- [ 0.408333] NET: Registered protocol family 2
- [ 0.413122] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
- [ 0.421106] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
- [ 0.429357] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.437107] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
- [ 0.444224] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.450760] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
- [ 0.457288] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
- [ 0.464594] NET: Registered protocol family 1
- [ 0.468817] PCI: CLS 0 bytes, default 32
- [ 0.473679] gptu: totally 6 16-bit timers/counters
- [ 0.478475] gptu: misc_register on minor 63
- [ 0.482784] gptu: succeeded to request irq 126
- [ 0.487103] gptu: succeeded to request irq 127
- [ 0.491696] gptu: succeeded to request irq 128
- [ 0.496142] gptu: succeeded to request irq 129
- [ 0.500645] gptu: succeeded to request irq 130
- [ 0.505241] gptu: succeeded to request irq 131
- [ 0.509877] No VPEs reserved for AP/SP, not initialize VPE loader
- [ 0.509877] Pass maxvpes=<n> argument as kernel argument
- [ 0.521244] No TCs reserved for AP/SP, not initializing RTLX.
- [ 0.521244] Pass maxtcs=<n> argument as kernel argument
- [ 0.534937] workingset: timestamp_bits=30 max_order=15 bucket_order=0
- [ 0.548556] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.554362] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.577895] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
- [ 0.586863] printk: console [ttyLTQ0] enabled
- [ 0.595533] printk: bootconsole [early0] disabled
- [ 0.608075] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
- [ 0.612988] nand: Samsung NAND 128MiB 3,3V 8-bit
- [ 0.617596] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
- [ 0.625336] Scanning device for bad blocks
- [ 0.649994] Bad eraseblock 228 at 0x000001c80000
- [ 0.654065] Bad eraseblock 238 at 0x000001dc0000
- [ 0.678041] Bad eraseblock 469 at 0x000003aa0000
- [ 0.729906] 4 fixed-partitions partitions found on MTD device 10000000.flash
- [ 0.735532] Creating 4 MTD partitions on "10000000.flash":
- [ 0.741006] 0x000000000000-0x000000040000 : "uboot"
- [ 0.747169] 0x000000040000-0x000000060000 : "u-boot-env"
- [ 0.753249] 0x000000060000-0x000000360000 : "kernel"
- [ 0.758682] 0x000000360000-0x000008000000 : "ubi"
- [ 0.766364] random: fast init done
- [ 0.767445] libphy: Fixed MDIO Bus: probed
- [ 0.783637] NET: Registered protocol family 17
- [ 0.786755] 8021q: 802.1Q VLAN Support v1.8
- [ 0.903202] libphy: lantiq,xrx200-mdio: probed
- [ 0.913594] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.3 0:00: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.3] (mii_bus:phy_addr=0:00, irq=POLL)
- [ 0.927257] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.3 0:01: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.3] (mii_bus:phy_addr=0:01, irq=POLL)
- [ 0.941622] Intel XWAY PHY11G (xRX v1.1 integrated) 0:11: attached PHY driver [Intel XWAY PHY11G (xRX v1.1 integrated)] (mii_bus:phy_addr=0:11, irq=POLL)
- [ 0.955236] Intel XWAY PHY11G (xRX v1.1 integrated) 0:13: attached PHY driver [Intel XWAY PHY11G (xRX v1.1 integrated)] (mii_bus:phy_addr=0:13, irq=POLL)
- [ 0.968990] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.3 0:05: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.3] (mii_bus:phy_addr=0:05, irq=POLL)
- [ 0.984718] UBI: auto-attach mtd3
- [ 0.986601] ubi0: attaching mtd3
- [ 1.151907] ubi0: scanning is finished
- [ 1.167979] ubi0: attached mtd3 (name "ubi", size 124 MiB)
- [ 1.172129] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
- [ 1.178889] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
- [ 1.185698] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
- [ 1.192448] ubi0: good PEBs: 994, bad PEBs: 3, corrupted PEBs: 0
- [ 1.198383] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
- [ 1.205681] ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 644105531
- [ 1.214715] ubi0: available PEBs: 0, total reserved PEBs: 994, PEBs reserved for bad PEB handling: 17
- [ 1.224025] ubi0: background thread "ubi_bgt0d" started, PID 441
- [ 1.232964] block ubiblock0_0: created from ubi0:0(rootfs)
- [ 1.236999] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
- [ 1.251918] VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
- [ 1.261523] Freeing unused kernel memory: 1256K
- [ 1.264615] This architecture does not have kernel memory protection.
- [ 1.271100] Run /sbin/init as init process
- [ 1.860038] init: Console is alive
- [ 1.862425] init: - watchdog -
- [ 2.937372] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 3.056844] dwc2 1e101000.usb: 1e101000.usb supply vusb_d not found, using dummy regulator
- [ 3.063902] dwc2 1e101000.usb: 1e101000.usb supply vusb_a not found, using dummy regulator
- [ 3.173556] dwc2 1e101000.usb: DWC OTG Controller
- [ 3.176939] dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
- [ 3.183994] dwc2 1e101000.usb: irq 62, io mem 0x1e101000
- [ 3.190475] hub 1-0:1.0: USB hub found
- [ 3.193083] hub 1-0:1.0: 1 port detected
- [ 3.198212] dwc2 1e106000.usb: 1e106000.usb supply vusb_d not found, using dummy regulator
- [ 3.205282] dwc2 1e106000.usb: 1e106000.usb supply vusb_a not found, using dummy regulator
- [ 3.315398] dwc2 1e106000.usb: DWC OTG Controller
- [ 3.318704] dwc2 1e106000.usb: new USB bus registered, assigned bus number 2
- [ 3.325833] dwc2 1e106000.usb: irq 91, io mem 0x1e106000
- [ 3.332446] hub 2-0:1.0: USB hub found
- [ 3.334873] hub 2-0:1.0: 1 port detected
- [ 3.341604] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 3.351819] init: - preinit -
- [ 4.692299] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
- [ 4.838966] random: procd: uninitialized urandom read (4 bytes read)
- [ 8.038572] UBIFS (ubi0:1): Mounting in unauthenticated mode
- [ 8.043205] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 524
- [ 8.171996] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
- [ 8.178384] UBIFS (ubi0:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
- [ 8.188384] UBIFS (ubi0:1): FS size: 118960128 bytes (113 MiB, 922 LEBs), journal size 5935104 bytes (5 MiB, 46 LEBs)
- [ 8.198961] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
- [ 8.205598] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 58A53B21-BC56-4976-B931-2B2096E09755, small LPT model
- [ 8.218203] mount_root: overlay filesystem has not been fully initialized yet
- [ 8.225119] mount_root: switching to ubifs overlay
- [ 8.588781] urandom-seed: Seed file not found (/etc/urandom.seed)
- [ 8.757801] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
- [ 8.776077] procd: - early -
- [ 8.777705] procd: - watchdog -
- [ 9.418863] procd: - watchdog -
- [ 9.421475] procd: - ubus -
- [ 9.518950] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 9.526446] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 9.536043] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 9.547245] procd: - init -
- [ 10.587197] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 10.596255] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
- [ 10.608950] tun: Universal TUN/TAP device driver, 1.6
- [ 10.629357] hidraw: raw HID events driver (C) Jiri Kosina
- [ 10.636893] GACT probability on
- [ 10.640631] Mirror/redirect action on
- [ 10.659124] u32 classifier
- [ 10.660370] input device check on
- [ 10.664127] Actions configured
- [ 10.688561] Loading modules backported from Linux version v5.10.34-0-g0aa66717f684
- [ 10.694788] Backport generated by backports.git v5.10.34-1-0-g7b5533e1
- [ 10.713449] Infineon Technologies DEU driver version 2.0.0
- [ 10.719810] IFX DEU DES initialized (multiblock).
- [ 10.724917] IFX DEU AES initialized (multiblock).
- [ 10.728843] IFX DEU ARC4 initialized (multiblock).
- [ 10.733628] IFX DEU SHA1 initialized.
- [ 10.736963] IFX DEU MD5 initialized.
- [ 10.740536] IFX DEU SHA1_HMAC initialized.
- [ 10.744830] IFX DEU MD5_HMAC initialized.
- [ 10.763238] usbcore: registered new interface driver usbhid
- [ 10.767361] usbhid: USB HID core driver
- [ 10.776489] usbcore: registered new interface driver usbserial_generic
- [ 10.781930] usbserial: USB Serial support registered for generic
- [ 10.810478] xt_time: kernel timezone is -0000
- [ 10.844208] usbcore: registered new interface driver cp210x
- [ 10.848538] usbserial: USB Serial support registered for cp210x
- [ 10.858429] usbcore: registered new interface driver ftdi_sio
- [ 10.863059] usbserial: USB Serial support registered for FTDI USB Serial Device
- [ 10.955721] usbcore: registered new interface driver pl2303
- [ 10.960044] usbserial: USB Serial support registered for pl2303
- [ 10.986427] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
- [ 10.992968] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
- [ 11.051941] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 11.068875] urngd: v1.0.2 started.
- [ 11.434871] random: crng init done
- [ 11.436869] random: 6 urandom warning(s) missed due to ratelimiting
- [ 24.075782] device eth0 entered promiscuous mode
- [ 27.161230] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
- [ 238.273805] lantiq,xrx200-net 1e108000.eth eth0: port 0 got link
- [ 239.323854] lantiq,xrx200-net 1e108000.eth eth0: port 0 lost link
- [ 240.353684] lantiq,xrx200-net 1e108000.eth eth0: port 0 got link
- [ 463.952612] lantiq,xrx200-net 1e108000.eth eth0: port 0 lost link
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement