Eachine - US65 Pro (Crossfire) - 3.5.7 (Factory)

# Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: https://www.fpvknowitall.com/ultimate-fpv-shopping-list
# SUPPORT ME ON PATREON at: http://bit.ly/2Ep5Sia
# THIS IS MY FULL TIME JOB. Here are other ways that you can support me: https://www.fpvknowitall.com/support-me/

# This diff was provided by a member of the community and has not been validated. If you have unmodified factory config dumps
# for your bind and fly quads, please send them to [email protected]

# diff all

# version
# Betaflight / CRAZYBEEF4DX (C4DX) 3.5.7 Mar 15 2019 / 21:41:52 (e9130527c) MSP API: 1.40

board_name CRAZYBEEF4DX
manufacturer_id
mcu_id 005600123439510836383737
signature

# reset configuration to default settings
defaults nosave

# name
name US65PRO

# resources

# mixer

# servo

# servo mix


# feature
feature -TELEMETRY
feature -ANTI_GRAVITY
feature AIRMODE

# beeper

# beacon
beacon RX_LOST
beacon RX_SET

# map

# serial
serial 0 64 115200 57600 0 115200
serial 1 2048 115200 57600 0 115200

# led

# color

# mode_color

# aux
aux 0 0 0 1800 2100 0 0
aux 1 1 1 900 1200 0 0
aux 2 35 2 1800 2100 0 0

# adjrange
adjrange 0 0 1 900 1200 12 1 0 0
adjrange 1 1 1 1200 1800 12 1 0 0
adjrange 2 2 1 1800 2100 12 1 0 0

# rxrange

# vtx

# rxfail

# master
set gyro_lowpass2_hz = 0
set rc_smoothing_type = FILTER
set serialrx_provider = CRSF
set dshot_idle_value = 550
set motor_pwm_protocol = DSHOT600
set vbat_max_cell_voltage = 45
set vbat_min_cell_voltage = 29
set vbat_warning_cell_voltage = 30
set ibata_scale = 1175
set yaw_motors_reversed = ON
set small_angle = 180
set deadband = 1
set yaw_deadband = 1
set pid_process_denom = 1
set osd_warn_batt_not_full = OFF
set osd_warn_batt_warning = OFF
set osd_warn_esc_fail = OFF
set osd_warn_core_temp = OFF
set osd_vbat_pos = 2433
set osd_rssi_pos = 2362
set osd_tim_2_pos = 2423
set osd_flymode_pos = 2457
set osd_throttle_pos = 2392
set osd_current_pos = 2368
set osd_mah_drawn_pos = 2400
set osd_craft_name_pos = 2442
set osd_warnings_pos = 2345
set osd_avg_cell_voltage_pos = 353
set osd_disarmed_pos = 2314
set osd_stat_tim_1 = ON
set osd_stat_max_spd = OFF
set osd_stat_battery = ON
set osd_stat_bbox = OFF
set osd_stat_bb_no = OFF
set vtx_band = 3
set vtx_channel = 3
set vtx_power = 2
set vtx_freq = 5665

# profile
profile 0


# profile
profile 1

set dterm_lowpass2_hz = 0
set dterm_notch_cutoff = 0
set p_pitch = 52
set p_roll = 51
set p_yaw = 72
set i_yaw = 55
set f_yaw = 100

# profile
profile 2


# restore original profile selection
profile 1

# rateprofile
rateprofile 0

set roll_rc_rate = 120
set pitch_rc_rate = 120
set yaw_rc_rate = 130

# rateprofile
rateprofile 1


# rateprofile
rateprofile 2


# rateprofile
rateprofile 3


# rateprofile
rateprofile 4


# rateprofile
rateprofile 5


# restore original rateprofile selection
rateprofile 0

# save configuration
save
#