**SMS Control** rev_04

/********* Pleasedontcode.com **********

    Pleasedontcode thanks you for automatic code generation! Enjoy your code!

    - Terms and Conditions:
    You have a non-exclusive, revocable, worldwide, royalty-free license
    for personal and commercial use. Attribution is optional; modifications
    are allowed, but you're responsible for code maintenance. We're not
    liable for any loss or damage. For full terms,
    please visit pleasedontcode.com/termsandconditions.

    - Project: **SMS Control**
    - Source Code NOT compiled for: Arduino Uno
    - Source Code created on: 2024-12-05 23:23:15

********* Pleasedontcode.com **********/

/****** SYSTEM REQUIREMENTS *****/
/****** SYSTEM REQUIREMENT 1 *****/
    /* Develop a project utilizing the SIM900 GSM module */
    /* for sending and receiving SMS messages. Ensure the */
    /* SoftwareSerial interface on A0 and A1 is */
    /* configured for seamless communication and */
    /* implement basic command responses. */
/****** SYSTEM REQUIREMENT 2 *****/
    /* each time receive a new sms so increase pot value */
    /* of 5% */
/****** END SYSTEM REQUIREMENTS *****/

/* START CODE */

/****** DEFINITION OF LIBRARIES *****/
#include <SoftwareSerial.h>
#include <sim900.h> //https://github.com/nthnn
#include <X9C10X.h> //https://github.com/RobTillaart/X9C10X

/****** FUNCTION PROTOTYPES *****/
void setup(void);
void loop(void);
void updateOutputs();
void checkForSMS();
void increasePotValue(float increment);

/***** DEFINITION OF DIGITAL OUTPUT PINS *****/
const uint8_t pot_X9C10X_CS_PIN_D2      = 2;
const uint8_t pot_X9C10X_INC_PIN_D3     = 3;
const uint8_t pot_X9C10X_UD_PIN_D4      = 4;

/***** DEFINITION OF Software Serial *****/
const uint8_t gsm_SIM900A_Serial_PIN_SERIAL_TX_A0       = A0;
const uint8_t gsm_SIM900A_Serial_PIN_SERIAL_RX_A1       = A1;
SoftwareSerial gsm_SIM900A_Serial(gsm_SIM900A_Serial_PIN_SERIAL_RX_A1, gsm_SIM900A_Serial_PIN_SERIAL_TX_A0);

/***** DEFINITION OF OUTPUT RAW VARIABLES *****/
/***** used to store raw data *****/
bool    pot_X9C10X_CS_PIN_D2_rawData        = 0;
bool    pot_X9C10X_INC_PIN_D3_rawData       = 0;
bool    pot_X9C10X_UD_PIN_D4_rawData        = 0;

/***** DEFINITION OF OUTPUT PHYSICAL VARIABLES *****/
/***** used to store data after characteristic curve transformation *****/
float   pot_X9C10X_CS_PIN_D2_phyData        = 0.0;
float   pot_X9C10X_INC_PIN_D3_phyData       = 0.0;
float   pot_X9C10X_UD_PIN_D4_phyData        = 0.0;

/****** DEFINITION OF LIBRARIES CLASS INSTANCES*****/
// Create an instance of the SIM900 class
SIM900 gsmModule(&gsm_SIM900A_Serial);

void setup(void)
{
    // put your setup code here, to run once:

    pinMode(pot_X9C10X_CS_PIN_D2,    OUTPUT);
    pinMode(pot_X9C10X_INC_PIN_D3,   OUTPUT);
    pinMode(pot_X9C10X_UD_PIN_D4,    OUTPUT);

    gsm_SIM900A_Serial.begin(9600);
    gsmModule.handshake(); // Initialize GSM module
}

void loop(void)
{
    // put your main code here, to run repeatedly:
    checkForSMS(); // Check for incoming SMS
    updateOutputs(); // Refresh output data
}

void updateOutputs()
{
    digitalWrite(pot_X9C10X_CS_PIN_D2, pot_X9C10X_CS_PIN_D2_rawData);
    digitalWrite(pot_X9C10X_INC_PIN_D3, pot_X9C10X_INC_PIN_D3_rawData);
    digitalWrite(pot_X9C10X_UD_PIN_D4, pot_X9C10X_UD_PIN_D4_rawData);
}

void checkForSMS()
{
    if (gsmModule.isCardReady())
    {
        String message = gsmModule.getResponse(); // Get the SMS message
        if (message.length() > 0) // If a new SMS is received
        {
            increasePotValue(5.0); // Increase potentiometer value by 5%
        }
    }
}

void increasePotValue(float increment)
{
    // Assuming the potentiometer value is represented in percentage
    pot_X9C10X_INC_PIN_D3_phyData += increment; // Increase pot value
    if (pot_X9C10X_INC_PIN_D3_phyData > 100.0) // Limit to 100%
    {
        pot_X9C10X_INC_PIN_D3_phyData = 100.0;
    }
    pot_X9C10X_INC_PIN_D3_rawData = (int)(pot_X9C10X_INC_PIN_D3_phyData / 100.0 * 255); // Convert to raw data
}

/* END CODE */