API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Jan 29th, 2019
115
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 28.67 KB | None | 0 0
raw download clone embed print report
  1. # Smoothieboard configuration file, see http://smoothieware.org/configuring-smoothie
  2. # NOTE Lines must not exceed 132 characters, and '#' characters mean what follows is ignored
  3. ## Robot module configurations : general handling of movement G-codes and slicing into moves
  4. # P3 steel setup
  5.  
  6. # Basic motion configuration
  7. default_feed_rate 6000 # Default speed (mm/minute) for G1/G2/G3 moves
  8. default_seek_rate 6000 # Default speed (mm/minute) for G0 moves
  9. mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs, 0 to disable
  10. #mm_per_line_segment 5 # Cut lines into segments this size
  11. mm_max_arc_error 0.01 # The maximum error for line segments that divide arcs 0 to disable
  12. # note it is invalid for both the above be 0
  13. # if both are used, will use largest segment length based on radius
  14.  
  15. # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
  16. # See http://smoothieware.org/stepper-motors
  17. alpha_steps_per_mm 160 # Steps per mm for alpha ( X ) stepper
  18. beta_steps_per_mm 160 # Steps per mm for beta ( Y ) stepper
  19. gamma_steps_per_mm 3200 # Steps per mm for gamma ( Z ) stepper
  20.  
  21. # Planner module configuration : Look-ahead and acceleration configuration
  22. # See http://smoothieware.org/motion-control
  23. acceleration 3000 # Acceleration in mm/second/second.
  24. #z_acceleration 500 # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
  25. junction_deviation 0.05 # See http://smoothieware.org/motion-control#junction-deviation
  26. #z_junction_deviation 0.0 # For Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
  27.  
  28. # Cartesian axis speed limits
  29. x_axis_max_speed 9000 # Maximum speed in mm/min
  30. y_axis_max_speed 9000 # Maximum speed in mm/min
  31. z_axis_max_speed 300 # Maximum speed in mm/min
  32.  
  33. # Stepper module configuration
  34. # Pins are defined as ports, and pin numbers, appending "!" to the number will invert a pin
  35. # See http://smoothieware.org/pin-configuration and http://smoothieware.org/pinout
  36. alpha_step_pin 2.0 # Pin for alpha stepper step signal
  37. alpha_dir_pin 0.5 # Pin for alpha stepper direction, add '!' to reverse direction
  38. alpha_en_pin 0.4 # Pin for alpha enable pin
  39. alpha_current 1.0 # X stepper motor current
  40. alpha_max_rate 30000.0 # Maximum rate in mm/min
  41.  
  42. beta_step_pin 2.1 # Pin for beta stepper step signal
  43. beta_dir_pin 0.11 # Pin for beta stepper direction, add '!' to reverse direction
  44. beta_en_pin 0.10 # Pin for beta enable
  45. beta_current 1.0 # Y stepper motor current
  46. beta_max_rate 30000.0 # Maxmimum rate in mm/min
  47.  
  48. gamma_step_pin 2.2 # Pin for gamma stepper step signal
  49. gamma_dir_pin 0.20! # Pin for gamma stepper direction, add '!' to reverse direction
  50. gamma_en_pin 0.19 # Pin for gamma enable
  51. gamma_current 1.2 # Z stepper motor current
  52. gamma_max_rate 600.0 # Maximum rate in mm/min
  53.  
  54. ## Extruder module configuration
  55. # See http://smoothieware.org/extruder
  56. extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
  57. extruder.hotend.steps_per_mm 419 # Steps per mm for extruder stepper
  58. extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  59. extruder.hotend.acceleration 500 # Acceleration for the stepper motor mm/sec²
  60. extruder.hotend.max_speed 50 # Maximum speed in mm/s
  61.  
  62. extruder.hotend.step_pin 2.3 # Pin for extruder step signal
  63. extruder.hotend.dir_pin 0.22! # Pin for extruder dir signal ( add '!' to reverse direction )
  64. extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
  65.  
  66. # Extruder offset
  67. #extruder.hotend.x_offset 0 # X offset from origin in mm
  68. #extruder.hotend.y_offset 0 # Y offset from origin in mm
  69. #extruder.hotend.z_offset 0 # Z offset from origin in mm
  70.  
  71. # Firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
  72. #extruder.hotend.retract_length 3 # Retract length in mm
  73. #extruder.hotend.retract_feedrate 45 # Retract feedrate in mm/sec
  74. #extruder.hotend.retract_recover_length 0 # Additional length for recover
  75. #extruder.hotend.retract_recover_feedrate 8 # Recover feedrate in mm/sec (should be less than retract feedrate)
  76. #extruder.hotend.retract_zlift_length 0 # Z-lift on retract in mm, 0 disables
  77. #extruder.hotend.retract_zlift_feedrate 6000 # Z-lift feedrate in mm/min (Note mm/min NOT mm/sec)
  78.  
  79. delta_current 1.2 # First extruder stepper motor current
  80.  
  81. # Second extruder module configuration
  82. #extruder.hotend2.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
  83. #extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper
  84. #extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  85. #extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  86. #extruder.hotend2.max_speed 50 # mm/s
  87.  
  88. #extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
  89. #extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal ( add '!' to reverse direction )
  90. #extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
  91.  
  92. #extruder.hotend2.x_offset 0 # x offset from origin in mm
  93. #extruder.hotend2.y_offset 25.0 # y offset from origin in mm
  94. #extruder.hotend2.z_offset 0 # z offset from origin in mm
  95.  
  96. #epsilon_current 1.5 # Second extruder stepper motor current
  97.  
  98.  
  99. ## Laser module configuration
  100. # See http://smoothieware.org/laser
  101. laser_module_enable false # Whether to activate the laser module at all
  102. laser_module_pwm_pin 2.5 # This pin will be PWMed to control the laser.
  103. # Only pins 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 1.18, 1.20, 1.21, 1.23, 1.24, 1.26, 3.25 and 3.26
  104. # can be used since laser requires hardware PWM, see http://smoothieware.org/pinout
  105. #laser_module_ttl_pin 1.30 # This pin turns on when the laser turns on, and off when the laser turns off.
  106. #laser_module_maximum_power 1.0 # This is the maximum duty cycle that will be applied to the laser
  107. #laser_module_minimum_power 0.0 # This is a value just below the minimum duty cycle that keeps the laser
  108. # active without actually burning.
  109. #laser_module_default_power 0.8 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
  110. # the maximum and minimum power levels specified above
  111. #laser_module_pwm_period 20 # This sets the pwm frequency as the period in microseconds
  112.  
  113. ## Temperature control configuration
  114. # See http://smoothieware.org/temperaturecontrol
  115.  
  116. # First hotend configuration
  117. temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all.
  118. temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
  119. temperature_control.hotend.heater_pin 2.7 # Pin that controls the heater, set to nc if a readonly thermistor is being defined
  120. temperature_control.hotend.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#toc5
  121. #temperature_control.hotend.beta 4066 # Or set the beta value
  122. temperature_control.hotend.set_m_code 104 # M-code to set the temperature for this module
  123. temperature_control.hotend.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  124. temperature_control.hotend.designator T # Designator letter for this module
  125. #temperature_control.hotend.max_temp 300 # Set maximum temperature - Will prevent heating above 300 by default
  126. #temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below if set
  127.  
  128. # Safety control is enabled by default and can be overidden here, the values show the defaults
  129. # See http://smoothieware.org/temperaturecontrol#runaway
  130. #temperature_control.hotend.runaway_heating_timeout 900 # How long it can take to heat up, max is 2040 seconds.
  131. #temperature_control.hotend.runaway_cooling_timeout 0 # How long it can take to cool down if temp is set lower, max is 2040 seconds
  132. #temperature_control.hotend.runaway_range 20 # How far from the set temperature it can wander, max setting is 63°C
  133.  
  134. # PID configuration
  135. # See http://smoothieware.org/temperaturecontrol#pid
  136. #temperature_control.hotend.p_factor 13.7 # P ( proportional ) factor
  137. #temperature_control.hotend.i_factor 0.097 # I ( integral ) factor
  138. #temperature_control.hotend.d_factor 24 # D ( derivative ) factor
  139.  
  140. #temperature_control.hotend.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  141.  
  142. # Second hotend configuration
  143. #temperature_control.hotend2.enable true # Whether to activate this ( "hotend" ) module at all.
  144. #temperature_control.hotend2.thermistor_pin 0.25 # Pin for the thermistor to read
  145. #temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater
  146. #temperature_control.hotend2.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#thermistor
  147. ##temperature_control.hotend2.beta 4066 # or set the beta value
  148. #temperature_control.hotend2.set_m_code 104 # M-code to set the temperature for this module
  149. #temperature_control.hotend2.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  150. #temperature_control.hotend2.designator T1 # Designator letter for this module
  151.  
  152. #temperature_control.hotend2.p_factor 13.7 # P ( proportional ) factor
  153. #temperature_control.hotend2.i_factor 0.097 # I ( integral ) factor
  154. #temperature_control.hotend2.d_factor 24 # D ( derivative ) factor
  155.  
  156. #temperature_control.hotend2.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  157.  
  158. temperature_control.bed.enable true # Whether to activate this ( "hotend" ) module at all.
  159. temperature_control.bed.thermistor_pin 0.24 # Pin for the thermistor to read
  160. temperature_control.bed.heater_pin 2.5 # Pin that controls the heater
  161. temperature_control.bed.thermistor Honeywell100K # See http://smoothieware.org/temperaturecontrol#thermistor
  162. #temperature_control.bed.beta 3974 # Or set the beta value
  163. temperature_control.bed.set_m_code 140 # M-code to set the temperature for this module
  164. temperature_control.bed.set_and_wait_m_code 190 # M-code to set-and-wait for this module
  165. temperature_control.bed.designator B # Designator letter for this module
  166.  
  167. # Bang-bang ( simplified ) control
  168. # See http://smoothieware.org/temperaturecontrol#bang-bang
  169. #temperature_control.bed.bang_bang false # Set to true to use bang bang control rather than PID
  170. #temperature_control.bed.hysteresis 2.0 # Set to the temperature in degrees C to use as hysteresis
  171.  
  172. ## Switch modules
  173. # See http://smoothieware.org/switch
  174.  
  175. # Switch module for fan control
  176. switch.fan.enable true # Enable this module
  177. switch.fan.input_on_command M106 # Command that will turn this switch on
  178. switch.fan.input_off_command M107 # Command that will turn this switch off
  179. switch.fan.output_pin 2.4 # Pin this module controls
  180. switch.fan.output_type pwm # PWM output settable with S parameter in the input_on_comand
  181. #switch.fan.max_pwm 255 # Set max pwm for the pin default is 255
  182.  
  183. #switch.misc.enable true # Enable this module
  184. #switch.misc.input_on_command M42 # Command that will turn this switch on
  185. #switch.misc.input_off_command M43 # Command that will turn this switch off
  186. #switch.misc.output_pin 2.4 # Pin this module controls
  187. #switch.misc.output_type digital # Digital means this is just an on or off pin
  188.  
  189. ## Temperatureswitch
  190. # See http://smoothieware.org/temperatureswitch
  191. # Automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
  192. # Useful to turn on a fan or water pump to cool the hotend
  193. #temperatureswitch.hotend.enable true #
  194. #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
  195. #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch
  196. #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch
  197. #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
  198. #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
  199.  
  200. ## Endstops
  201. # See http://smoothieware.org/endstops
  202. endstops_enable true # The endstop module is enabled by default and can be disabled here
  203. #corexy_homing false # Set to true if homing on a hbot or corexy
  204. #alpha_min_endstop 1.24!^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  205. alpha_max_endstop 1.25!^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  206. alpha_homing_direction home_to_max # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  207. alpha_min 0 # This gets loaded as the current position after homing when home_to_min is set
  208. alpha_max 200 # This gets loaded as the current position after homing when home_to_max is set
  209. #beta_min_endstop 1.26!^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  210. beta_max_endstop 1.27!^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  211. beta_homing_direction home_to_max # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  212. beta_min 0 # This gets loaded as the current position after homing when home_to_min is set
  213. beta_max 200 # This gets loaded as the current position after homing when home_to_max is set
  214. gamma_min_endstop 1.28!^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  215. #gamma_max_endstop 1.29^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  216. gamma_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  217. gamma_min 0 # This gets loaded as the current position after homing when home_to_min is set
  218. gamma_max 200 # This gets loaded as the current position after homing when home_to_max is set
  219.  
  220. alpha_max_travel 230 # Max travel in mm for alpha/X axis when homing
  221. beta_max_travel 210 # Max travel in mm for beta/Y axis when homing
  222. gamma_max_travel 200 # Max travel in mm for gamma/Z axis when homing
  223.  
  224. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered
  225. #alpha_limit_enable false # Set to true to enable X min and max limit switches
  226. #beta_limit_enable false # Set to true to enable Y min and max limit switches
  227. #gamma_limit_enable false # Set to true to enable Z min and max limit switches
  228.  
  229. # Endstops home at their fast feedrate first, then once the endstop is found they home again at their slow feedrate for accuracy
  230. alpha_fast_homing_rate_mm_s 50 # Alpha/X fast homing feedrate in mm/second
  231. alpha_slow_homing_rate_mm_s 25 # Alpha/X slow homing feedrate in mm/second
  232. beta_fast_homing_rate_mm_s 50 # Beta/Y fast homing feedrate in mm/second
  233. beta_slow_homing_rate_mm_s 25 # Beta/Y slow homing feedrate in mm/second
  234. gamma_fast_homing_rate_mm_s 4 # Gamma/Z fast homing feedrate in mm/second
  235. gamma_slow_homing_rate_mm_s 2 # Gamma/Z slow homing feedrate in mm/second
  236.  
  237. alpha_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for alpha/X
  238. beta_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for beta/Y
  239. gamma_homing_retract_mm 1 # Distance to retract from the endstop after it is hit for gamma/Z
  240.  
  241.  
  242. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered (all are set for delta)
  243. #alpha_limit_enable false # Set to true to enable X min and max limit switches
  244. #beta_limit_enable false # Set to true to enable Y min and max limit switches
  245. #gamma_limit_enable false # Set to true to enable Z min and max limit switches
  246.  
  247. # Optional order in which axis will home, default is they all home at the same time,
  248. # If this is set it will force each axis to home one at a time in the specified order
  249. #homing_order XYZ # X axis followed by Y then Z last
  250. #move_to_origin_after_home false # Move XY to 0,0 after homing
  251. #endstop_debounce_count 100 # Uncomment if you get noise on your endstops, default is 100
  252. #endstop_debounce_ms 1 # Uncomment if you get noise on your endstops, default is 1 millisecond debounce
  253. #home_z_first true # Uncomment and set to true to home the Z first, otherwise Z homes after XY
  254.  
  255. # End of endstop config
  256. # Delete the above endstop section and uncomment next line and copy and edit Snippets/abc-endstop.config file to enable endstops for ABC axis
  257. #include abc-endstop.config
  258.  
  259. ##BLTouch Servo Settings
  260. switch.servo.enable true
  261. switch.servo.input_on_command M280 S3.0
  262. switch.servo.input_off_command M280 S7.0
  263. switch.servo.output_pin 1.23
  264. switch.servo.output_type hwpwm
  265. switch.servo.pwm_period_ms 20
  266.  
  267. ## Z-probe
  268. # See http://smoothieware.org/zprobe
  269. zprobe.enable true # Set to true to enable a zprobe
  270. zprobe.probe_pin 1.28 # Pin probe is attached to, if NC remove the !
  271. zprobe.slow_feedrate 10 # Mm/sec probe feed rate
  272. #zprobe.debounce_ms 1 # Set if noisy
  273. zprobe.fast_feedrate 200 # Move feedrate mm/sec
  274. zprobe.probe_height 8 # How much above bed to start probe
  275. #gamma_min_endstop nc # Normally 1.28. Change to nc to prevent conflict,
  276.  
  277. # Probing rectangular grid
  278. leveling-strategy.rectangular-grid.enable true
  279. leveling-strategy.rectangular-grid.x_size 200
  280. leveling-strategy.rectangular-grid.y_size 200
  281. leveling-strategy.rectangular-grid.size 7
  282. leveling-strategy.rectangular-grid.do_home false
  283. leveling-strategy.rectangular-grid.probe_offsets 26,25,0
  284. leveling-strategy.rectangular-grid.initial_height 8
  285. leveling-strategy.rectangular-grid.save true
  286. mm_per_line_segment 1 #
  287.  
  288. # Levelling strategy
  289. # Example for 3-point levelling strategy, see wiki documentation for other strategies
  290. #leveling-strategy.three-point-leveling.enable true # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
  291. #leveling-strategy.three-point-leveling.point1 100.0,0.0 # the first probe point (x,y) optional may be defined with M557
  292. #leveling-strategy.three-point-leveling.point2 200.0,200.0 # the second probe point (x,y)
  293. #leveling-strategy.three-point-leveling.point3 0.0,200.0 # the third probe point (x,y)
  294. #leveling-strategy.three-point-leveling.home_first true # home the XY axis before probing
  295. #leveling-strategy.three-point-leveling.tolerance 0.03 # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
  296. #leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset
  297. #leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false
  298.  
  299. ## Panel
  300. # See http://smoothieware.org/panel
  301. # Please find your panel on the wiki and copy/paste the right configuration here
  302. panel.enable false # Set to true to enable the panel code
  303.  
  304. # Example for reprap discount GLCD
  305. # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
  306. # +5v is EXP1 pin 10, Gnd is EXP1 pin 9
  307. #panel.lcd reprap_discount_glcd #
  308. #panel.spi_channel 0 # SPI channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
  309. #panel.spi_cs_pin 0.16 # SPI chip select ; GLCD EXP1 Pin 4
  310. #panel.encoder_a_pin 3.25!^ # Encoder pin ; GLCD EXP2 Pin 3
  311. #panel.encoder_b_pin 3.26!^ # Encoder pin ; GLCD EXP2 Pin 5
  312. #panel.click_button_pin 1.30!^ # Click button ; GLCD EXP1 Pin 2
  313. #panel.buzz_pin 1.31 # Pin for buzzer ; GLCD EXP1 Pin 1
  314. #panel.back_button_pin 2.11!^ # Back button ; GLCD EXP2 Pin 8
  315.  
  316. panel.menu_offset 0 # Some panels will need 1 here
  317.  
  318. panel.alpha_jog_feedrate 6000 # X jogging feedrate in mm/min
  319. panel.beta_jog_feedrate 6000 # Y jogging feedrate in mm/min
  320. panel.gamma_jog_feedrate 200 # Z jogging feedrate in mm/min
  321.  
  322. panel.hotend_temperature 185 # Temp to set hotend when preheat is selected
  323. panel.bed_temperature 60 # Temp to set bed when preheat is selected
  324.  
  325. ## Custom menus : Example of a custom menu entry, which will show up in the Custom entry.
  326. # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
  327. custom_menu.power_on.enable true #
  328. custom_menu.power_on.name Power_on #
  329. custom_menu.power_on.command M80 #
  330.  
  331. custom_menu.power_off.enable true #
  332. custom_menu.power_off.name Power_off #
  333. custom_menu.power_off.command M81 #
  334.  
  335.  
  336. ## Network settings
  337. # See http://smoothieware.org/network
  338. network.enable false # Enable the ethernet network services
  339. network.webserver.enable true # Enable the webserver
  340. network.telnet.enable true # Enable the telnet server
  341. network.ip_address auto # Use dhcp to get ip address
  342. # Uncomment the 3 below to manually setup ip address
  343. #network.ip_address 192.168.3.222 # The IP address
  344. #network.ip_mask 255.255.255.0 # The ip mask
  345. #network.ip_gateway 192.168.3.1 # The gateway address
  346. #network.mac_override xx.xx.xx.xx.xx.xx # Override the mac address, only do this if you have a conflict
  347.  
  348. ## System configuration
  349. # Serial communications configuration ( baud rate defaults to 9600 if undefined )
  350. # For communication over the UART port, *not* the USB/Serial port
  351. uart0.baud_rate 115200 # Baud rate for the default hardware ( UART ) serial port
  352.  
  353. second_usb_serial_enable false # This enables a second USB serial port
  354. #leds_disable true # Disable using leds after config loaded
  355. #play_led_disable true # Disable the play led
  356.  
  357. # Kill button maybe assigned to a different pin, set to the onboard pin by default
  358. # See http://smoothieware.org/killbutton
  359. kill_button_enable true # Set to true to enable a kill button
  360. kill_button_pin 2.12 # Kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
  361.  
  362. #msd_disable false # Disable the MSD (USB SDCARD), see http://smoothieware.org/troubleshooting#disable-msd
  363. #dfu_enable false # For linux developers, set to true to enable DFU
  364.  
  365. # Only needed on a smoothieboard
  366. # See http://smoothieware.org/currentcontrol
  367. currentcontrol_module_enable true # Control stepper motor current via the configuration file
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!