Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- WTMI-devel-18.12.0-a0a1cb8
- WTMI: system early-init
- SVC REV: 5, CPU VDD voltage: 1.132V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL1: Built : 09:50:21, Feb 20 2019
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL2: Built : 09:50:23, Feb 20 2019
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL31: Built : 09:5
- U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1000 [MHz]
- L2 800 [MHz]
- TClock 200 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link up
- MMC: sdhci@d0000: 0, sdhci@d8000: 1
- Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
- OK
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 0
- switch to partitions #0, OK
- mmc0 is current device
- 16421376 bytes read in 713 ms (22 MiB/s)
- 7891941 bytes read in 349 ms (21.6 MiB/s)
- 8942 bytes read in 19 ms (459 KiB/s)
- ## Loading init Ramdisk from Legacy Image at 01100000 ...
- Image Name: uInitrd
- Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
- Data Size: 7891877 Bytes = 7.5 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 06000000
- Booting using the fdt blob at 0x6000000
- Loading Ramdisk to 3eea5000, end 3f62bba5 ... OK
- Using Device Tree in place at 0000000006000000, end 00000000060052ed
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
- [ 0.000000] Linux version 4.19.20-mvebu64 (root@armbian.com) (gcc version 7.2 .1 20171011 (Linaro GCC 7.2-2017.11)) #5.75 SMP PREEMPT Fri Feb 8 09:54:18 CET 2 019
- [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
- [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '')
- [ 0.000000] bootconsole [ar3700_uart0] enabled
- [ 0.000000] efi: Getting EFI parameters from FDT:
- [ 0.000000] efi: UEFI not found.
- [ 0.000000] cma: Reserved 16 MiB at 0x000000003dc00000
- [ 0.000000] NUMA: No NUMA configuration found
- [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000003fffffff ]
- [ 0.000000] NUMA: NODE_DATA [mem 0x3ffea180-0x3ffeb93f]
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA32 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] Normal empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv1.1 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
- [ 0.000000] psci: SMC Calling Convention v1.1
- [ 0.000000] random: get_random_bytes called from start_kernel+0xa8/0x418 with crng_init=0
- [ 0.000000] percpu: Embedded 23 pages/cpu @(____ptrval____) s56984 r8192 d290 32 u94208
- [ 0.000000] Detected VIPT I-cache on CPU0
- [ 0.000000] CPU features: enabling workaround for ARM erratum 845719
- [ 0.000000] Speculative Store Bypass Disable mitigation not required
- [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 257536
- [ 0.000000] Policy zone: DMA32
- [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0 xd0012000 root=/dev/mmcblk1p1 rw rootwait
- [ 0.000000] Memory: 989168K/1046528K available (11388K kernel code, 740K rwda ta, 3228K rodata, 640K init, 517K bss, 40976K reserved, 16384K cma-reserved)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
- [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2.
- [ 0.000000] Tasks RCU enabled.
- [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
- [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
- [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
- [ 0.000000] GICv3: Distributor has no Range Selector support
- [ 0.000000] GICv3: no VLPI support, no direct LPI support
- [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
- [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
- [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 43980 46511080ns
- [ 0.008445] Console: colour dummy device 80x25
- [ 0.013012] Calibrating delay loop (skipped), value calculated using timer fr equency.. 25.00 BogoMIPS (lpj=50000)
- [ 0.023517] pid_max: default: 32768 minimum: 301
- [ 0.028334] Security Framework initialized
- [ 0.033090] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
- [ 0.040656] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
- [ 0.047690] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.054570] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.086020] ASID allocator initialised with 32768 entries
- [ 0.099531] rcu: Hierarchical SRCU implementation.
- [ 0.112618] EFI services will not be available.
- [ 0.125228] smp: Bringing up secondary CPUs ...
- [ 0.161982] Detected VIPT I-cache on CPU1
- [ 0.162012] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000
- [ 0.162048] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
- [ 0.162141] smp: Brought up 1 node, 2 CPUs
- [ 0.184214] SMP: Total of 2 processors activated.
- [ 0.189043] CPU features: detected: GIC system register CPU interface
- [ 0.195680] CPU features: detected: 32-bit EL0 Support
- [ 0.204060] CPU: All CPU(s) started at EL2
- [ 0.208214] alternatives: patching kernel code
- [ 0.213590] devtmpfs: initialized
- [ 0.219259] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 7645041785100000 ns
- [ 0.229260] futex hash table entries: 512 (order: 3, 32768 bytes)
- [ 0.236090] xor: measuring software checksum speed
- [ 0.281036] 8regs : 1919.000 MB/sec
- [ 0.325300] 8regs_prefetch: 1710.000 MB/sec
- [ 0.369922] 32regs : 2359.000 MB/sec
- [ 0.414185] 32regs_prefetch: 1983.000 MB/sec
- [ 0.418857] xor: using function: 32regs (2359.000 MB/sec)
- [ 0.424477] pinctrl core: initialized pinctrl subsystem
- [ 0.430403] DMI not present or invalid.
- [ 0.434606] NET: Registered protocol family 16
- [ 0.439480] audit: initializing netlink subsys (disabled)
- [ 0.445144] audit: type=2000 audit(0.380:1): state=initialized audit_enabled= 0 res=1
- [ 0.453102] cpuidle: using governor ladder
- [ 0.457349] cpuidle: using governor menu
- [ 0.461548] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval___ _))
- [ 0.469095] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
- [ 0.477941] DMA: preallocated 2048 KiB pool for atomic allocations
- [ 0.484401] Serial: AMBA PL011 UART driver
- [ 0.498708] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
- [ 0.505944] cryptd: max_cpu_qlen set to 1000
- [ 0.576903] raid6: int64x1 gen() 394 MB/s
- [ 0.649329] raid6: int64x1 xor() 372 MB/s
- [ 0.721771] raid6: int64x2 gen() 597 MB/s
- [ 0.794214] raid6: int64x2 xor() 511 MB/s
- [ 0.866671] raid6: int64x4 gen() 905 MB/s
- [ 0.939125] raid6: int64x4 xor() 647 MB/s
- [ 1.011158] raid6: int64x8 gen() 836 MB/s
- [ 1.083219] raid6: int64x8 xor() 632 MB/s
- [ 1.155358] raid6: neonx1 gen() 625 MB/s
- [ 1.227362] raid6: neonx1 xor() 723 MB/s
- [ 1.299439] raid6: neonx2 gen() 1021 MB/s
- [ 1.371485] raid6: neonx2 xor() 1031 MB/s
- [ 1.443567] raid6: neonx4 gen() 1319 MB/s
- [ 1.515615] raid6: neonx4 xor() 1237 MB/s
- [ 1.587668] raid6: neonx8 gen() 1437 MB/s
- [ 1.659740] raid6: neonx8 xor() 1312 MB/s
- [ 1.664054] raid6: using algorithm neonx8 gen() 1437 MB/s
- [ 1.669608] raid6: .... xor() 1312 MB/s, rmw enabled
- [ 1.674715] raid6: using neon recovery algorithm
- [ 1.679732] ACPI: Interpreter disabled.
- [ 1.684084] vgaarb: loaded
- [ 1.687107] SCSI subsystem initialized
- [ 1.691301] usbcore: registered new interface driver usbfs
- [ 1.696912] usbcore: registered new interface driver hub
- [ 1.702385] usbcore: registered new device driver usb
- [ 1.707725] pps_core: LinuxPPS API ver. 1 registered
- [ 1.712758] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti <giometti@linux.it>
- [ 1.722174] PTP clock support registered
- [ 1.726964] clocksource: Switched to clocksource arch_sys_counter
- [ 1.733336] VFS: Disk quotas dquot_6.6.0
- [ 1.737356] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
- [ 1.744553] pnp: PnP ACPI: disabled
- [ 1.753543] NET: Registered protocol family 2
- [ 1.758508] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes)
- [ 1.766393] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
- [ 1.773681] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
- [ 1.780454] TCP: Hash tables configured (established 8192 bind 8192)
- [ 1.787110] UDP hash table entries: 512 (order: 2, 16384 bytes)
- [ 1.793168] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
- [ 1.799858] NET: Registered protocol family 1
- [ 1.808735] RPC: Registered named UNIX socket transport module.
- [ 1.814802] RPC: Registered udp transport module.
- [ 1.819598] RPC: Registered tcp transport module.
- [ 1.824434] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 1.831068] NET: Registered protocol family 44
- [ 1.835843] Trying to unpack rootfs image as initramfs...
- [ 2.212865] Freeing initrd memory: 7704K
- [ 2.217426] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters av ailable
- [ 2.225530] kvm [1]: 8-bit VMID
- [ 2.229008] kvm [1]: vgic-v2@d1da0000
- [ 2.232722] kvm [1]: GIC system register CPU interface enabled
- [ 2.238765] kvm [1]: vgic interrupt IRQ1
- [ 2.242810] kvm [1]: Hyp mode initialized successfully
- [ 2.252025] Initialise system trusted keyrings
- [ 2.256737] workingset: timestamp_bits=44 max_order=18 bucket_order=0
- [ 2.270218] NFS: Registering the id_resolver key type
- [ 2.275385] Key type id_resolver registered
- [ 2.279654] Key type id_legacy registered
- [ 2.283778] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
- [ 2.290500] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
- [ 2.297078] SGI XFS with ACLs, security attributes, realtime, no debug enable d
- [ 2.309911] NET: Registered protocol family 38
- [ 2.314436] Key type asymmetric registered
- [ 2.318633] Asymmetric key parser 'x509' registered
- [ 2.323714] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 47)
- [ 2.331397] io scheduler noop registered
- [ 2.335361] io scheduler deadline registered
- [ 2.339932] io scheduler cfq registered (default)
- [ 2.344701] io scheduler mq-deadline registered
- [ 2.349361] io scheduler kyber registered
- [ 2.353584] io scheduler bfq registered
- [ 2.360548] advk-pcie d0070000.pcie: host bridge /soc/pcie@d0070000 ranges:
- [ 2.367720] advk-pcie d0070000.pcie: MEM 0xe8000000..0xe8ffffff -> 0xe80000 00
- [ 2.375191] advk-pcie d0070000.pcie: IO 0xe9000000..0xe900ffff -> 0xe90000 00
- [ 2.482748] advk-pcie d0070000.pcie: link up
- [ 2.487207] advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
- [ 2.493593] pci_bus 0000:00: root bus resource [bus 00-ff]
- [ 2.499237] pci_bus 0000:00: root bus resource [mem 0xe8000000-0xe8ffffff]
- [ 2.506313] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus addre ss [0xe9000000-0xe900ffff])
- [ 2.517440] pci 0000:00:00.0: BAR 2: assigned [mem 0xe8000000-0xe8003fff 64bi t]
- [ 2.524932] pci 0000:00:00.0: BAR 0: assigned [io 0x1000-0x10ff]
- [ 2.532766] mv_xor d0060900.xor: Marvell shared XOR driver
- [ 2.567658] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy int r )
- [ 2.603686] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy int r )
- [ 2.613940] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
- [ 2.622040] cacheinfo: Unable to detect cache hierarchy for CPU 0
- TIM-1.0
- WTMI-devel-18.12.0-a0a1cb8
- WTMI: system early-init
- SVC REV: 5, CPU VDD voltage: 1.132V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL1: Built : 09:50:21, Feb 20 2019
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL2: Built : 09:50:23, Feb 20 2019
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL31: Built : 09:5
- U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1000 [MHz]
- L2 800 [MHz]
- TClock 200 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- TIM-1.0
- WTMI-devel-18.12.0-a0a1cb8
- WTMI: system early-init
- SVC REV: 5, CPU VDD voltage: 1.132V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL1: Built : 09:50:21, Feb 20 2019
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL2: Built : 09:50:23, Feb 20 2019
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL31: Built : 09:5
- U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1000 [MHz]
- L2 800 [MHz]
- TClock 200 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link up
- MMC: sdhci@d0000: 0, sdhci@d8000: 1
- Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
- OK
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 0
- switch to partitions #0, OK
- mmc0 is current device
- 16421376 bytes read in 710 ms (22.1 MiB/s)
- 7891941 bytes read in 348 ms (21.6 MiB/s)
- 8942 bytes read in 19 ms (459 KiB/s)
- ## Loading init Ramdisk from Legacy Image at 01100000 ...
- Image Name: uInitrd
- Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
- Data Size: 7891877 Bytes = 7.5 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 06000000
- Booting using the fdt blob at 0x6000000
- Loading Ramdisk to 3eea5000, end 3f62bba5 ... OK
- Using Device Tree in place at 0000000006000000, end 00000000060052ed
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
- [ 0.000000] Linux version 4.19.20-mvebu64 (root@armbian.com) (gcc version 7.2 .1 20171011 (Linaro GCC 7.2-2017.11)) #5.75 SMP PREEMPT Fri Feb 8 09:54:18 CET 2 019
- [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
- [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '')
- [ 0.000000] bootconsole [ar3700_uart0] enabled
- [ 0.000000] efi: Getting EFI parameters from FDT:
- [ 0.000000] efi: UEFI not found.
- [ 0.000000] cma: Reserved 16 MiB at 0x000000003dc00000
- [ 0.000000] NUMA: No NUMA configuration found
- [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000003fffffff ]
- [ 0.000000] NUMA: NODE_DATA [mem 0x3ffea180-0x3ffeb93f]
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA32 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] Normal empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv1.1 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
- [ 0.000000] psci: SMC Calling Convention v1.1
- [ 0.000000] random: get_random_bytes called from start_kernel+0xa8/0x418 with crng_init=0
- [ 0.000000] percpu: Embedded 23 pages/cpu @(____ptrval____) s56984 r8192 d290 32 u94208
- [ 0.000000] Detected VIPT I-cache on CPU0
- [ 0.000000] CPU features: enabling workaround for ARM erratum 845719
- [ 0.000000] Speculative Store Bypass Disable mitigation not required
- [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 257536
- [ 0.000000] Policy zone: DMA32
- [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0 xd0012000 root=/dev/mmcblk1p1 rw rootwait
- [ 0.000000] Memory: 989168K/1046528K available (11388K kernel codeWTMI-devel- 18.12.0-a0a1cb8
- WTMI: system early-init
- SVC REV: 5, CPU VDD voltage: 1.132V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL1: Built : 09:50:21, Feb 20 2019
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL2: Built : 09:50:23, Feb 20 2019
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL31: Built : 09:5
- U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1000 [MHz]
- L2 800 [MHz]
- TClock 200 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- TIM-1.0
- WTMI-devel-18.12.0-a0a1cb8
- WTMI: system early-init
- SVC REV: 5, CPU VDD voltage: 1.132V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL1: Built : 09:50:21, Feb 20 2019
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL2: Built : 09:50:23, Feb 20 2019
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL31: Built : 09:5
- U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1000 [MHz]
- L2 800 [MHz]
- TClock 200 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link up
- MMC: sdhci@d0000: 0, sdhci@d8000: 1
- Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
- OK
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 0
- switch to partitions #0, OK
- mmc0 is current device
- 16421376 bytes read in 710 ms (22.1 MiB/s)
- 7891941 bytes read in 348 ms (21.6 MiB/s)
- 8942 bytes read in 19 ms (459 KiB/s)
- ## Loading init Ramdisk from Legacy Image at 01100000 ...
- Image Name: uInitrd
- Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
- Data Size: 7891877 Bytes = 7.5 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 06000000
- Booting using the fdt blob at 0x6000000
- Loading Ramdisk to 3eea5000, end 3f62bba5 ... OK
- Using Device Tree in place at 0000000006000000, end 00000000060052ed
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
- [ 0.000000] Linux version 4.19.20-mvebu64 (root@armbian.com) (gcc version 7.2 .1 20171011 (Linaro GCC 7.2-2017.11)) #5.75 SMP PREEMPT Fri Feb 8 09:54:18 CET 2 019
- [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
- [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '')
- [ 0.000000] bootconsole [ar3700_uart0] enabled
- [ 0.000000] efi: Getting EFI parameters from FDT:
- [ 0.000000] efi: UEFI not found.
- [ 0.000000] cma: Reserved 16 MiB at 0x000000003dc00000
- [ 0.000000] NUMA: No NUMA configuration found
- [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000003fffffff ]
- [ 0.000000] NUMA: NODE_DATA [mem 0x3ffea180-0x3ffeb93f]
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA32 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] Normal empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv1.1 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
- [ 0.000000] psci: SMC Calling Convention v1.1
- [ 0.000000] random: get_random_bytes called from start_kernel+0xa8/0x418 with crng_init=0
- [ 0.000000] percpu: Embedded 23 pages/cpu @(____ptrval____) s56984 r8192 d290 32 u94208
- [ 0.000000] Detected VIPT I-cache on CPU0
- [ 0.000000] CPU features: enabling workaround for ARM erratum 845719
- [ 0.000000] Speculative Store Bypass Disable mitigation not required
- [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 257536
- [ 0.000000] Policy zone: DMA32
- [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0 xd0012000 root=/dev/mmcblk1p1 rw rootwait
- [ 0.000000] Memory: 989168K/1046528K available (11388K kernel code, 740K rwda ta, 3228K rodata, 640K init, 517K bss, 40976K reserved, 16384K cma-reserved)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
- [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2.
- [ 0.000000] Tasks RCU enabled.
- [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
- [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
- [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
- [ 0.000000] GICv3: Distributor has no Range Selector support
- [ 0.000000] GICv3: no VLPI support, no direct LPI support
- [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
- [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
- [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 43980 46511080ns
- [ 0.008442] Console: colour dummy device 80x25
- [ 0.013009] Calibrating delay loop (skipped), value calculated using timer fr equency.. 25.00 BogoMIPS (lpj=50000)
- [ 0.023513] pid_max: default: 32768 minimum: 301
- [ 0.028331] Security Framework initialized
- [ 0.033082] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
- [ 0.040653] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
- [ 0.047686] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.054567] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.086016] ASID allocator initialised with 32768 entries
- [ 0.099526] rcu: Hierarchical SRCU implementation.
- [ 0.112609] EFI services will not be available.
- [ 0.125219] smp: Bringing up secondary CPUs ...
- [ 0.161971] Detected VIPT I-cache on CPU1
- [ 0.162003] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000
- [ 0.162039] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
- [ 0.162133] smp: Brought up 1 node, 2 CPUs
- [ 0.184204] SMP: Total of 2 processors activated.
- [ 0.189034] CPU features: detected: GIC system register CPU interface
- [ 0.195671] CPU features: detected: 32-bit EL0 Support
- [ 0.204056] CPU: All CPU(s) started at EL2
- [ 0.208211] alternatives: patching kernel code
- [ 0.213589] devtmpfs: initialized
- [ 0.219279] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 7645041785100000 ns
- [ 0.229280] futex hash table entries: 512 (order: 3, 32768 bytes)
- [ 0.236113] xor: measuring software checksum speed
- [ 0.281056] 8regs : 1919.000 MB/sec
- [ 0.325320] 8regs_prefetch: 1710.000 MB/sec
- [ 0.369942] 32regs : 2359.000 MB/sec
- [ 0.414205] 32regs_prefetch: 1983.000 MB/sec
- [ 0.418878] xor: using function: 32regs (2359.000 MB/sec)
- [ 0.424496] pinctrl core: initialized pinctrl subsystem
- [ 0.430421] DMI not present or invalid.
- [ 0.434621] NET: Registered protocol family 16
- [ 0.439496] audit: initializing netlink subsys (disabled)
- [ 0.445167] audit: type=2000 audit(0.380:1): state=initialized audit_enabled= 0 res=1
- [ 0.453121] cpuidle: using governor ladder
- [ 0.457371] cpuidle: using governor menu
- [ 0.461570] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval___ _))
- [ 0.469119] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
- [ 0.477964] DMA: preallocated 2048 KiB pool for atomic allocations
- [ 0.484422] Serial: AMBA PL011 UART driver
- [ 0.498717] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
- [ 0.505960] cryptd: max_cpu_qlen set to 1000
- [ 0.576878] raid6: int64x1 gen() 393 MB/s
- [ 0.649298] raid6: int64x1 xor() 372 MB/s
- [ 0.721725] raid6: int64x2 gen() 597 MB/s
- [ 0.794130] raid6: int64x2 xor() 511 MB/s
- [ 0.866583] raid6: int64x4 gen() 905 MB/s
- [ 0.939036] raid6: int64x4 xor() 647 MB/s
- [ 1.011073] raid6: int64x8 gen() 836 MB/s
- [ 1.083127] raid6: int64x8 xor() 632 MB/s
- [ 1.155266] raid6: neonx1 gen() 625 MB/s
- [ 1.227272] raid6: neonx1 xor() 723 MB/s
- [ 1.299343] raid6: neonx2 gen() 1021 MB/s
- [ 1.371388] raid6: neonx2 xor() 1031 MB/s
- [ 1.443477] raid6: neonx4 gen() 1319 MB/s
- [ 1.515525] raid6: neonx4 xor() 1237 MB/s
- [ 1.587593] raid6: neonx8 gen() 1437 MB/s
- [ 1.659645] raid6: neonx8 xor() 1312 MB/s
- [ 1.663960] raid6: using algorithm neonx8 gen() 1437 MB/s
- [ 1.669513] raid6: .... xor() 1312 MB/s, rmw enabled
- [ 1.674621] raid6: using neon recovery algorithm
- [ 1.679639] ACPI: Interpreter disabled.
- [ 1.683993] vgaarb: loaded
- [ 1.687013] SCSI subsystem initialized
- [ 1.691210] usbcore: registered new interface driver usbfs
- [ 1.696821] usbcore: registered new interface driver hub
- [ 1.702294] usbcore: registered new device driver usb
- [ 1.707636] pps_core: LinuxPPS API ver. 1 registered
- [ 1.712669] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti <giometti@linux.it>
- [ 1.722085] PTP clock support registered
- [ 1.726879] clocksource: Switched to clocksource arch_sys_counter
- [ 1.733252] VFS: Disk quotas dquot_6.6.0
- [ 1.737270] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
- [ 1.744464] pnp: PnP ACPI: disabled
- [ 1.753392] NET: Registered protocol family 2
- [ 1.758356] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes)
- [ 1.766243] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
- [ 1.773531] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
- [ 1.780306] TCP: Hash tables configured (established 8192 bind 8192)
- [ 1.786963] UDP hash table entries: 512 (order: 2, 16384 bytes)
- [ 1.793015] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
- [ 1.799712] NET: Registered protocol family 1
- [ 1.804602] RPC: Registered named UNIX socket transport module.
- [ 1.810653] RPC: Registered udp transport module.
- [ 1.815464] RPC: Registered tcp transport module.
- [ 1.820300] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 1.826950] NET: Registered protocol family 44
- [ 1.831685] Trying to unpack rootfs image as initramfs...
- TIM-1.0
- WTMI-devel-18.12.0-a0a1cb8
- WTMI: system early-init
- SVC REV: 5, CPU VDD voltage: 1.132V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL1: Built : 09:50:21, Feb 20 2019
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL2: Built : 09:50:23, Feb 20 2019
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL31: Built : 09:5
- U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1000 [MHz]
- L2 800 [MHz]
- TClock 200 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link up
- MMC: sdhci@d0000: 0, sdhci@d8000: 1
- Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
- OK
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 2 TIM-1.0
- WTMI-devel-18.12.0-a0a1cb8
- WTMI: system early-init
- SVC REV: 5, CPU VDD voltage: 1.132V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL1: Built : 09:50:21, Feb 20 2019
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL2: Built : 09:50:23, Feb 20 2019
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL31: Built : 09:5
- U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1000 [MHz]
- L2 800 [MHz]
- TClock 200 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link up
- MMC: sdhci@d0000: 0, sdhci@d8000: 1
- Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
- OK
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 0
- switch to partitions #0, OK
- mmc0 is current device
- 16421376 bytes read in 710 ms (22.1 MiB/s)
- 7891941 bytes read in 348 ms (21.6 MiB/s)
- 8942 bytes read in 18 ms (484.4 KiB/s)
- ## Loading init Ramdisk from Legacy Image at 01100000 ...
- Image Name: uInitrd
- Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
- Data Size: 7891877 Bytes = 7.5 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 06000000
- Booting using the fdt blob at 0x6000000
- Loading Ramdisk to 3eea5000, end 3f62bba5 ... OK
- Using Device Tree in place at 0000000006000000, end 00000000060052ed
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
- [ 0.000000] Linux version 4.19.20-mvebu64 (root@armbian.com) (gcc version 7.2 .1 20171011 (Linaro GCC 7.2-2017.11)) #5.75 SMP PREEMPT Fri Feb 8 09:54:18 CET 2 019
- [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
- [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '')
- [ 0.000000] bootconsole [ar3700_uart0] enabled
- [ 0.000000] efi: Getting EFI parameters from FDT:
- [ 0.000000] efi: UEFI not found.
- [ 0.000000] cma: Reserved 16 MiB at 0x000000003dc00000
- [ 0.000000] NUMA: No NUMA configuration found
- [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000003fffffff ]
- [ 0.000000] NUMA: NODE_DATA [mem 0x3ffea180-0x3ffeb93f]
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA32 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] Normal empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv1.1 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
- [ 0.000000] psci: SMC Calling Convention v1.1
- [ 0.000000] random: get_random_bytes called from start_kernel+0xa8/0x418 with crng_init=0
- [ 0.000000] percpu: Embedded 23 pages/cpu @(____ptrval____) s56984 r8192 d290 32 u94208
- [ 0.000000] Detected VIPT I-cache on CPU0
- [ 0.000000] CPU features: enabling workaround for ARM erratum 845719
- [ 0.000000] Speculative Store Bypass Disable mitigation not required
- [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 257536
- [ 0.000000] Policy zone: DMA32
- [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0 xd0012000 root=/dev/mmcblk1p1 rw rootwait
- [ 0.000000] Memory: 989168K/1046528K available (11388K kernel code, 740K rwda ta, 3228K rodata, 640K init, 517K bss, 40976K reserved, 16384K cma-reserved)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
- [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2.
- [ 0.000000] Tasks RCU enabled.
- [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
- [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
- [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
- [ 0.000000] GICv3: Distributor has no Range Selector support
- [ 0.000000] GICv3: no VLPI support, no direct LPI support
- [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
- [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
- [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 43980 46511080ns
- [ 0.008443] Console: colour dummy device 80x25
- [ 0.013011] Calibrating delay loop (skipped), value calculated using timer fr equency.. 25.00 BogoMIPS (lpj=50000)
- [ 0.023516] pid_max: default: 32768 minimum: 301
- [ 0.028332] Security Framework initialized
- [ 0.033082] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
- [ 0.040648] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
- [ 0.047681] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.054561] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.086011] ASID allocator initialised with 32768 entries
- [ 0.099523] rcu: Hierarchical SRCU implementation.
- TIM-1.0
- WTMI-devel-18.12.0-a0a1cb8
- WTMI: system early-init
- SVC REV: 5, CPU VDD voltage: 1.132V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL1: Buill▒TIM-1.0
- WTMI-devel-18.12.0-a0a1cb8
- WTMI: system early-init
- SVC REV: 5, CPU VDD voltage: 1.132V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL1: Built : 09:50:21, Feb 20 2019
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL2: Built : 09:50:23, Feb 20 2019
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL31: Built : 09:5
- U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1000 [MHz]
- L2 800 [MHz]
- TClock 200 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link up
- MMC: sdhci@d0000: 0, sdhci@d8000: 1
- Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
- OK
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 0
- switch to partitions #0, OK
- mmc0 is current device
- 16421376 bytes read in 713 ms (22 MiB/s)
- 7891941 bytes read in 349 ms (21.6 MiB/s)
- 8942 bytes read in 18 ms (484.4 KiB/s)
- ## Loading init Ramdisk from Legacy Image at 01100000 ...
- Image Name: uInitrd
- Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
- Data Size: 7891877 Bytes = 7.5 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 06000000
- Booting using the fdt blob at 0x6000000
- Loading Ramdisk to 3eea5000, end 3f62bba5 ... OK
- Using Device Tree in place at 0000000006000000, end 00000000060052ed
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
- [ 0.000000] Linux version 4.19.20-mvebu64 (root@armbian.com) (gcc version 7.2 .1 20171011 (Linaro GCC 7.2-2017.11)) #5.75 SMP PREEMPT Fri Feb 8 09:54:18 CET 2 019
- [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
- [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '')
- [ 0.000000] bootconsole [ar3700_uart0] enabled
- [ 0.000000] efi: Getting EFI parameters from FDT:
- [ 0.000000] efi: UEFI not found.
- [ 0.000000] cma: Reserved 16 MiB at 0x000000003dc00000
- [ 0.000000] NUMA: No NUMA configuration found
- [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000003fffffff ]
- [ 0.000000] NUMA: NODE_DATA [mem 0x3ffea180-0x3ffeb93f]
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA32 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] Normal empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv1.1 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
- [ 0.000000] psci: SMC Calling Convention v1.1
- [ 0.000000] random: get_random_bytes called from start_kernel+0xa8/0x418 with crng_init=0
- [ 0.000000] percpu: Embedded 23 pages/cpu @(____ptrval____) s56984 r8192 d290 32 u94208
- [ 0.000000] Detected VIPT I-cache on CPU0
- [ 0.000000] CPU features: enabling workaround for ARM erratum 845719
- [ 0.000000] Speculative Store Bypass Disable mitigation not required
- [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 257536
- [ 0.000000] Policy zone: DMA32
- [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0 xd0012000 root=/dev/mmcblk1p1 rw rootwait
- [ 0.000000] Memory: 989168K/1046528K available (11388K kernel code, 740K rwda ta, 3228K rodata, 640K init, 517K bss, 40976K reserved, 16384K cma-reserved)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
- [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2.
- [ 0.000000] Tasks RCU enabled.
- [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
- [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
- [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
- [ 0.000000] GICv3: Distributor has no Range Selector support
- [ 0.000000] GICv3: no VLPI support, no direct LPI support
- [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
- [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
- [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 43980 46511080ns
- [ 0.008443] Console: colour dummy device 80x25
- [ 0.013011] Calibrating delay loop (skipped), value calculated using timer fr equency.. 25.00 BogoMIPS (lpj=50000)
- [ 0.023516] pid_max: default: 32768 minimum: 301
- [ 0.028332] Security Framework initialized
- [ ▒TIM-1.0
- WTMI-devel-18.12.0-a0a1cb8
- WTMI: system early-init
- SVC REV: 5, CPU VDD voltage: 1.132V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL1: Built : 09:50:21, Feb 20 2019
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL2: Built : 09:50:23, Feb 20 2019
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL31: Built : 09:5
- U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1000 [MHz]
- L2 800 [MHz]
- TClock 200 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link up
- MMC: sdhci@d0000: 0, sdhci@d8000: 1
- Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
- OK
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 0
- switch to partitions #0, OK
- mmc0 is current device
- 16421376 bytes read in 711 ms (22 MiB/s)
- 7891941 bytes read in 349 ms (21.6 MiB/s)
- 8942 bytes read in 18 ms (484.4 KiB/s)
- ## Loading init Ramdisk from Legacy Image at 01100000 ...
- Image Name: uInitrd
- Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
- Data Size: 7891877 Bytes = 7.5 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 06000000
- Booting using the fdt blob at 0x6000000
- Loading Ramdisk to 3eea5000, end 3f62bba5 ... OK
- Using Device Tree in place at 0000000006000000, end 00000000060052ed
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
- [ 0.000000] Linux version 4.19.20-mvebu64 (root@armbian.com) (gcc version 7.2 .1 20171011 (Linaro GCC 7.2-2017.11)) #5.75 SMP PREEMPT Fri Feb 8 09:54:18 CET 2 019
- [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
- [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '')
- [ 0.000000] bootconsole [ar3700_uart0] enabled
- [ 0.000000] efi: Getting EFI parameters from FDT:
- [ 0.000000] efi: UEFI not found.
- [ 0.000000] cma: Reserved 16 MiB at 0x000000003dc00000
- [ 0.000000] NUMA: No NUMA configuration found
- [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000003fffffff ]
- [ 0.000000] NUMA: NODE_DATA [mem 0x3ffea180-0x3ffeb93f]
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA32 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] Normal empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv1.1 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
- [ 0.000000] psci: SMC Calling Convention v1.1
- [ 0..▒TIM-1.0
- WTMI-devel-18.12.0-a0a1cb8
- WTMI: system early-init
- SVC REV: 5, CPU VDD voltage: 1.132V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL1: Built : 09:50:21, Feb 20 2019
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL2: Built : 09:50:23, Feb 20 2019
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL31: Built : 09:5
- U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1000 [MHz]
- L2 800 [MHz]
- TClock 200 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link up
- MMC: sdhci@d0000: 0, sdhci@d8000: 1
- Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
- OK
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 0
- switch to partitions #0, OK
- mmc0 is current device
- 16421376 bytes read in 711 ms (22 MiB/s)
- 7891941 bytes read in 351 ms (21.4 MiB/s)
- 8942 bytes read in 18 ms (484.4 KiB/s)
- ## Loading init Ramdisk from Legacy Image at 01100000 ...
- Image Name: uInitrd
- Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
- Data Size: 7891877 Bytes = 7.5 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 06000000
- Booting using the fdt blob at 0x6000000
- Loading Ramdisk to 3eea5000, end 3f62bba5 ... OK
- Using Device Tree in place at 0000000006000000, end 00000000060052ed
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
- [ 0.000000] Linux version 4.19.20-mvebu64 (root@armbian.com) (gcc version 7.2 .1 20171011 (Linaro GCC 7.2-2017.11)) #5.75 SMP PREEMPT Fri Feb 8 09:54:18 CET 2 019
- [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
- [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '')
- [ 0.000000] bootconsole [ar3700_uart0] enabled
- [ 0.000000] efi: Getting EFI parameters from FDT:
- [ 0.000000] efi: UEFI not found.
- [ 0.000000] cma: Reserved 16 MiB at 0x000000003dc00000
- [ 0.000000] NUMA: No NUMA configuration found
- [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000003fffffff ]
- [ 0.000000] NUMA: NODE_DATA [mem 0x3ffea180-0x3ffeb93f]
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA32 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] Normal empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv1.1 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
- [ 0.000000] psci: SMC Calling Convention v1.1
- [ 0.000000] random: get_random_bytes called from start_kernel+0xa8/0x418 with crng_init=0
- [ 0.000000] percpu: Embedded 23 pages/cpu @(____ptrval____) s56984 r8192 d290 32 u94208
- [ 0.000000] Detected VIPT I-cache on CPU0
- [ 0.000000] CPU features: enabling workaround for ARM erratum 845719
- [ 0.000000] Speculative Store Bypass Disable mitigation not required
- [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 257536
- [ 0.000000] Policy zone: DMA32
- [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0 xd0012000 root=/dev/mmcblk1p1 rw rootwait
- [ 0.000000] Memory: 989168K/1046528K available (11388K kernel code, 740K rwda ta, 3228K rodata, 640K init, 517K bss, 40976K reserved, 16384K cma-reserved)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
- [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2.
- [ 0.000000] Tasks RCU enabled.
- [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
- [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
- [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
- [ 0.000000] GICv3: Distributor has no Range Selector support
- [ 0.000000] GICv3: no VLPI support, no direct LPI support
- [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
- [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
- [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 43980 46511080ns
- [ 0.008442] Console: colour dummy device 80x25
- [ 0.013011] Calibrating delay loop (skipped), value calculated using timer fr equency.. 25.00 BogoMIPS (lpj=50000)
- [ 0.023514] pid_max: default: 32768 minimum: 301
- [ 0.028332] Security Framework initialized
- [ 0.033082] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
- [ 0.040651] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
- [ 0.047685] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.054565] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.086014] ASID allocator initialised with 32768 entries
- [ 0.099526] rcu: Hierarchical SRCU implementation.
- [ 0.112610] EFI services will not be available.
- [ 0.125221] smp: Bringing up secondary CPUs ...
- [ 0.161973] Detected VIPT I-cache on CPU1
- [ 0.162005] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000
- [ 0.162041] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
- [ 0.162134] smp: Brought up 1 node, 2 CPUs
- [ 0.184206] SMP: Total of 2 processors activated.
- [ 0.189035] CPU features: detected: GIC system register CPU interface
- [ 0.195672] CPU features: detected: 32-bit EL0 Support
- [ 0.204057] CPU: All CPU(s) started at EL2
- [ 0.208212] alternatives: patching kernel code
- [ 0.213591] devtmpfs: initialized
- [ 0.219287] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 7645041785100000 ns
- [ 0.229286] futex hash table entries: 512 (order: 3, 32768 bytes)
- [ 0.236118] xor: measuring software checksum speed
- [ 0.281061] 8regs : 1919.000 MB/sec
- [ 0.325325] 8regs_prefetch: 1710.000 MB/sec
- [ 0.369947] 32regs : 2359.000 MB/sec
- [ 0.414211] 32regs_prefetch: 1983.000 MB/sec
- [ 0.418884] xor: using function: 32regs (2359.000 MB/sec)
- [ 0.424502] pinctrl core: initialized pinctrl subsystem
- [ 0.430429] DMI not present or invalid.
- [ 0.434629] NET: Registered protocol family 16
- [ 0.439502] audit: initializing netlink subsys (disabled)
- [ 0.445176] audit: type=2000 audit(0.380:1): state=initialized audit_enabled= 0 res=1
- [ 0.453131] cpuidle: using governor ladder
- [ 0.457381] cpuidle: using governor menu
- [ 0.461582] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval___ _))
- [ 0.469130] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
- [ 0.477977] DMA: preallocated 2048 KiB pool for atomic allocations
- [ 0.484434] Serial: AMBA PL011 UART driver
- [ 0.498740] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
- [ 0.505974] cryptd: max_cpu_qlen set to 1000
- [ 0.576857] raid6: int64x1 gen() 393 MB/s
- [ 0.649283] raid6: int64x1 xor() 373 MB/s
- [ 0.721689] raid6: int64x2 gen() 597 MB/s
- [ 0.794115] raid6: int64x2 xor() 511 MB/s
- [ 0.866551] raid6: int64x4 gen() 905 MB/s
- [ 0.938989] raid6: int64x4 xor() 647 MB/s
- [ 1.011046] raid6: int64x8 gen() 836 MB/s
- [ 1.083088] raid6: int64x8 xor() 632 MB/s
- [ 1.155191] raid6: neonx1 gen() 625 MB/s
- [ 1.227249] raid6: neonx1 xor() 723 MB/s
- [ 1.299287] raid6: neonx2 gen() 1021 MB/s
- [ 1.371358] raid6: neonx2 xor() 1031 MB/s
- [ 1.443435] raid6: neonx4 gen() 1319 MB/s
- [ 1.515494] raid6: neonx4 xor() 1237 MB/s
- [ 1.587548] raid6: neonx8 gen() 1437 MB/s
- [ 1.659611] raid6: neonx8 xor() 1311 MB/s
- [ 1.663925] raid6: using algorithm neonx8 gen() 1437 MB/s
- [ 1.669479] raid6: .... xor() 1311 MB/s, rmw enabled
- [ 1.674586] raid6: using neon recovery algorithm
- [ 1.679604] ACPI: Interpreter disabled.
- [ 1.683962] vgaarb: loaded
- [ 1.686982] SCSI subsystem initialized
- [ 1.691181] usbcore: registered new interface driver usbfs
- [ 1.696791] usbcore: registered new interface driver hub
- [ 1.702266] usbcore: registered new device driver usb
- [ 1.707607] pps_core: LinuxPPS API ver. 1 registered
- [ 1.712639] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti <giometti@linux.it>
- [ 1.722055] PTP clock support registered
- [ 1.726847] clocksource: Switched to clocksource arch_sys_counter
- [ 1.733218] VFS: Disk quotas dquot_6.6.0
- [ 1.737234] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
- [ 1.744430] pnp: PnP ACPI: disabled
- [ 1.753347] NET: Registered protocol family 2
- [ 1.758321] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes)
- [ 1.766207] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
- [ 1.773494] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
- [ 1.780269] TCP: Hash tables configured (established 8192 bind 8192)
- [ 1.786924] UDP hash table entries: 512 (order: 2, 16384 bytes)
- [ 1.792976] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
- [ 1.799671] NET: Registered protocol family 1
- [ 1.804564] RPC: Registered named UNIX socket transport module.
- [ 1.810608] RPC: Registered udp transport module.
- [ 1.815425] RPC: Registered tcp transport module.
- [ 1.820262] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 1.826911] NET: Registered protocol family 44
- [ 1.831667] Trying to unpack rootfs image as initramfs...
- [ 2.208851] Freeing initrd memory: 7704K
- [ 2.213398] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters av ailable
- [ 2.221497] kvm [1]: 8-bit VMID
- [ 2.224960] kvm [1]: vgic-v2@d1da0000
- [ 2.228674] kvm [1]: GIC system register CPU interface enabled
- [ 2.234716] kvm [1]: vgic interrupt IRQ1
- [ 2.238760] kvm [1]: Hyp mode initialized successfully
- [ 2.247918] Initialise system trusted keyrings
- [ 2.252633] workingset: timestamp_bits=44 max_order=18 bucket_order=0
- [ 2.266115] NFS: Registering the id_resolver key type
- [ 2.271289] Key type id_resolver registered
- [ 2.275546] Key type id_legacy registered
- [ 2.279678] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
- [ 2.286384] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
- [ 2.292968] SGI XFS with ACLs, security attributes, realtime, no debug enable d
- [ 2.305844] NET: Registered protocol family 38
- [ 2.310369] Key type asymmetric registered
- [ 2.314566] Asymmetric key parser 'x509' registered
- [ 2.319635] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 47)
- [ 2.327332] io scheduler noop registered
- [ 2.331295] io scheduler deadline registered
- [ 2.335867] io scheduler cfq registered (default)
- [ 2.340635] io scheduler mq-deadline registered
- [ 2.345296] io scheduler kyber registered
- [ 2.349517] io scheduler bfq registered
- [ 2.356455] advk-pcie d0070000.pcie: host bridge /soc/pcie@d0070000 ranges:
- [ 2.363616] advk-pcie d0070000.pcie: MEM 0xe8000000..0xe8ffffff -> 0xe80000 00
- [ 2.371102] advk-pcie d0070000.pcie: IO 0xe9000000..0xe900ffff -> 0xe90000 00
- [ 2.478654] advk-pcie d0070000.pcie: link up
- [ 2.483121] advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
- [ 2.489508] pci_bus 0000:00: root bus resource [bus 00-ff]
- [ 2.495147] pci_bus 0000:00: root bus resource [mem 0xe8000000-0xe8ffffff]
- [ 2.502231] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus addre ss [0xe9000000-0xe900ffff])
- [ 2.513351] pci 0000:00:00.0: BAR 2: assigned [mem 0xe8000000-0xe8003fff 64bi t]
- [ 2.520844] pci 0000:00:00.0: BAR 0: assigned [io 0x1000-0x10ff]
- [ 2.528635] mv_xor d0060900.xor: Marvell shared XOR driver
- [ 2.563544] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy int r )
- [ 2.599573] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy int r )
- [ 2.609800] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
- [ 2.617882] cacheinfo: Unable to detect cache hierarchy for CPU 0
- [ 2.624874] brd: module loaded
- TIM-1.0
- WTMI-devel-18.12.0-a0a1cb8
- WTMI: system early-init
- SVC REV: 5, CPU VDD voltage: 1.132V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL1: Built : 09:50:21, Feb 20 2019
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL2: Built : 09:50:23, Feb 20 2019
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
- NOTICE: BL31: Built : 09:5
- U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1000 [MHz]
- L2 800 [MHz]
- TClock 200 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link up
- MMC: sdhci@d0000: 0, sdhci@d8000: 1
- Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
- OK
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 0
- switch to partitions #0, OK
- mmc0 is current device
- 16421376 bytes read in 712 ms (22 MiB/s)
- 7891941 bytes read in 348 ms (21.6 MiB/s)
- 8942 bytes read in 19 ms (459 KiB/s)
- ## Loading init Ramdisk from Legacy Image at 01100000 ...
- Image Name: uInitrd
- Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
- Data Size: 7891877 Bytes = 7.5 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 06000000
- Booting using the fdt blob at 0x6000000
- Loading Ramdisk to 3eea5000, end 3f62bba5 ... OK
- Using Device Tree in place at 0000000006000000, end 00000000060052ed
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
- [ 0.000000] Linux version 4.19.20-mvebu64 (root@armbian.com) (gcc version 7.2 .1 20171011 (Linaro GCC 7.2-2017.11)) #5.75 SMP PREEMPT Fri Feb 8 09:54:18 CET 2 019
- [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
- [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '')
- [ 0.000000] bootconsole [ar3700_uart0] enabled
- [ 0.000000] efi: Getting EFI parameters from FDT:
- [ 0.000000] efi: UEFI not found.
- [ 0.000000] cma: Reserved 16 MiB at 0x000000003dc00000
- [ 0.000000] NUMA: No NUMA configuration found
- [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000003fffffff ]
- [ 0.000000] NUMA: NODE_DATA [mem 0x3ffea180-0x3ffeb93f]
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA32 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] Normal empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv1.1 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
- [ 0.000000] psci: SMC Calling Convention v1.1
- [ 0.000000] random: get_random_bytes called from start_kernel+0xa8/0x418 with crng_init=0
- [ 0.000000] percpu: Embedded 23 pages/cpu @(____ptrval____) s56984 r8192 d290 32 u94208
- [ 0.000000] Detected VIPT I-cache on CPU0
- [ 0.000000] CPU features: enabling workaround for ARM erratum 845719
- [ 0.000000] Speculative Store Bypass Disable mitigation not required
- [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 257536
- [ 0.000000] Policy zone: DMA32
- [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0 xd0012000 root=/dev/mmcblk1p1 rw rootwait
- [ 0.000000] Memory: 989168K/1046528K available (11388K kernel code, 740K rwda ta, 3228K rodata, 640K init, 517K bss, 40976K reserved, 16384K cma-reserved)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
- [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2.
- [ 0.000000] Tasks RCU enabled.
- [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
- [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
- [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
- [ 0.000000] GICv3: Distributor has no Range Selector support
- [ 0.000000] GICv3: no VLPI support, no direct LPI support
- [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
- [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
- [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 43980 46511080ns
- [ 0.008443] Console: colour dummy device 80x25
- [ 0.013009] Calibrating delay loop (skipped), value calculated using timer fr equency.. 25.00 BogoMIPS (lpj=50000)
- [ 0.023512] pid_max: default: 32768 minimum: 301
- [ 0.028329] Security Framework initialized
- [ 0.033078] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
- [ 0.040643] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
- [ 0.047676] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.054557] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.086006] ASID allocator initialised with 32768 entries
- [ 0.099518] rcu: Hierarchical SRCU implementation.
- [ 0.112606] EFI services will not be available.
- [ 0.125215] smp: Bringing up secondary CPUs ...
- [ 0.161969] Detected VIPT I-cache on CPU1
- [ 0.162001] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000
- [ 0.162038] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
- [ 0.162132] smp: Brought up 1 node, 2 CPUs
- [ 0.184204] SMP: Total of 2 processors activated.
- [ 0.189033] CPU features: detected: GIC system register CPU interface
- [ 0.195670] CPU features: detected: 32-bit EL0 Support
- [ 0.204054] CPU: All CPU(s) started at EL2
- [ 0.208208] alternatives: patching kernel code
- [ 0.213584] devtmpfs: initialized
- [ 0.219283] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 7645041785100000 ns
- [ 0.229283] futex hash table entries: 512 (order: 3, 32768 bytes)
- [ 0.236110] xor: measuring software checksum speed
- [ 0.281053] 8regs : 1919.000 MB/sec
- [ 0.325318] 8regs_prefetch: 1710.000 MB/sec
- [ 0.369939] 32regs : 2359.000 MB/sec
- [ 0.414202] 32regs_prefetch: 1983.000 MB/sec
- [ 0.418874] xor: using function: 32regs (2359.000 MB/sec)
- [ 0.424490] pinctrl core: initialized pinctrl subsystem
- [ 0.430415] DMI not present or invalid.
- [ 0.434618] NET: Registered protocol family 16
- [ 0.439495] audit: initializing netlink subsys (disabled)
- [ 0.445167] audit: type=2000 audit(0.380:1): state=initialized audit_enabled= 0 res=1
- [ 0.453122] cpuidle: using governor ladder
- [ 0.457372] cpuidle: using governor menu
- [ 0.461572] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval___ _))
- [ 0.469120] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
- [ 0.477961] DMA: preallocated 2048 KiB pool for atomic allocations
- [ 0.484414] Serial: AMBA PL011 UART driver
- [ 0.498713] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
- [ 0.505955] cryptd: max_cpu_qlen set to 1000
- [ 0.576920] raid6: int64x1 gen() 394 MB/s
- [ 0.649348] raid6: int64x1 xor() 373 MB/s
- [ 0.721833] raid6: int64x2 gen() 598 MB/s
- [ 0.794268] raid6: int64x2 xor() 511 MB/s
- [ 0.866711] raid6: int64x4 gen() 905 MB/s
- [ 0.939145] raid6: int64x4 xor() 647 MB/s
- [ 1.011204] raid6: int64x8 gen() 836 MB/s
- [ 1.083258] raid6: int64x8 xor() 632 MB/s
- [ 1.155334] raid6: neonx1 gen() 625 MB/s
- [ 1.227381] raid6: neonx1 xor() 723 MB/s
- [ 1.299484] raid6: neonx2 gen() 1021 MB/s
- [ 1.371514] raid6: neonx2 xor() 1031 MB/s
- [ 1.443609] raid6: neonx4 gen() 1319 MB/s
- [ 1.515649] raid6: neonx4 xor() 1237 MB/s
- [ 1.587724] raid6: neonx8 gen() 1437 MB/s
- [ 1.659769] raid6: neonx8 xor() 1312 MB/s
- [ 1.664084] raid6: using algorithm neonx8 gen() 1437 MB/s
- [ 1.669637] raid6: .... xor() 1312 MB/s, rmw enabled
- [ 1.674745] raid6: using neon recovery algorithm
- [ 1.679761] ACPI: Interpreter disabled.
- [ 1.684118] vgaarb: loaded
- [ 1.687136] SCSI subsystem initialized
- [ 1.691333] usbcore: registered new interface driver usbfs
- [ 1.696945] usbcore: registered new interface driver hub
- [ 1.702415] usbcore: registered new device driver usb
- [ 1.707760] pps_core: LinuxPPS API ver. 1 registered
- [ 1.712793] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti <giometti@linux.it>
- [ 1.722208] PTP clock support registered
- [ 1.726996] clocksource: Switched to clocksource arch_sys_counter
- [ 1.733367] VFS: Disk quotas dquot_6.6.0
- [ 1.737385] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
- [ 1.744579] pnp: PnP ACPI: disabled
- [ 1.753550] NET: Registered protocol family 2
- [ 1.758521] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes)
- [ 1.766408] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
- [ 1.773694] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
- [ 1.780469] TCP: Hash tables configured (established 8192 bind 8192)
- [ 1.787122] UDP hash table entries: 512 (order: 2, 16384 bytes)
- [ 1.793181] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
- [ 1.799870] NET: Registered protocol family 1
- [ 1.804755] RPC: Registered named UNIX socket transport module.
- [ 1.810804] RPC: Registered udp transport module.
- [ 1.815617] RPC: Registered tcp transport module.
- [ 1.820454] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 1.827103] NET: Registered protocol family 44
- [ 1.831836] Trying to unpack rootfs image as initramfs...
- [ 2.209221] Freeing initrd memory: 7704K
- [ 2.213730] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters av ailable
- [ 2.221819] kvm [1]: 8-bit VMID
- [ 2.225300] kvm [1]: vgic-v2@d1da0000
- [ 2.229015] kvm [1]: GIC system register CPU interface enabled
- [ 2.235041] kvm [1]: vgic interrupt IRQ1
- [ 2.239112] kvm [1]: Hyp mode initialized successfully
- [ 2.248239] Initialise system trusted keyrings
- [ 2.252956] workingset: timestamp_bits=44 max_order=18 bucket_order=0
- [ 2.266367] NFS: Registering the id_resolver key type
- [ 2.271541] Key type id_resolver registered
- [ 2.275798] Key type id_legacy registered
- [ 2.279931] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
- [ 2.286650] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
- [ 2.293233] SGI XFS with ACLs, security attributes, realtime, no debug enable d
- [ 2.306112] NET: Registered protocol family 38
- [ 2.310636] Key type asymmetric registered
- [ 2.314831] Asymmetric key parser 'x509' registered
- [ 2.319905] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 47)
- [ 2.327607] io scheduler noop registered
- [ 2.331569] io scheduler deadline registered
- [ 2.336138] io scheduler cfq registered (default)
- [ 2.340909] io scheduler mq-deadline registered
- [ 2.345567] io scheduler kyber registered
- [ 2.349790] io scheduler bfq registered
- [ 2.356727] advk-pcie d0070000.pcie: host bridge /soc/pcie@d0070000 ranges:
- [ 2.363888] advk-pcie d0070000.pcie: MEM 0xe8000000..0xe8ffffff -> 0xe80000 00
- [ 2.371363] advk-pcie d0070000.pcie: IO 0xe9000000..0xe900ffff -> 0xe90000 00
- [ 2.478926] advk-pcie d0070000.pcie: link up
- [ 2.483400] advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
- [ 2.489786] pci_bus 0000:00: root bus resource [bus 00-ff]
- [ 2.495426] pci_bus 0000:00: root bus resource [mem 0xe8000000-0xe8ffffff]
- [ 2.502505] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus addre ss [0xe9000000-0xe900ffff])
- [ 2.513630] pci 0000:00:00.0: BAR 2: assigned [mem 0xe8000000-0xe8003fff 64bi t]
- [ 2.521121] pci 0000:00:00.0: BAR 0: assigned [io 0x1000-0x10ff]
- [ 2.528935] mv_xor d0060900.xor: Marvell shared XOR driver
- [ 2.563674] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy int r )
- [ 2.599721] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy int r )
- [ 2.609959] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
- [ 2.618065] cacheinfo: Unable to detect cache hierarchy for CPU 0
- [ 2.625055] brd: module loaded
- [ 2.635110] loop: module loaded
- [ 2.639438] ahci-mvebu d00e0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
- [ 2.648703] ahci-mvebu d00e0000.sata: flags: ncq sntf led only pmp fbs pio sl um part sxs
- [ 2.658213] scsi host0: ahci-mvebu
- [ 2.661941] ata1: SATA max UDMA/133 mmio [mem 0xd00e0000-0xd00e1fff] port 0x1 00 irq 22
- [ 2.671244] m25p80 spi0.0: mx25u3235f (4096 Kbytes)
- [ 2.676292] 3 fixed-partitions partitions found on MTD device spi0.0
- [ 2.682768] Creating 3 MTD partitions on "spi0.0":
- [ 2.687694] 0x000000000000-0x0000003f0000 : "uboot"
- [ 2.693631] 0x0000003f0000-0x000000400000 : "ubootenv"
- [ 2.699629] 0x000000190000-0x000000f80000 : "Linux"
- [ 2.704596] mtd: partition "Linux" extends beyond the end of device "spi0.0" -- size truncated to 0x270000
- [ 2.715767] libphy: Fixed MDIO Bus: probed
- [ 2.720289] tun: Universal TUN/TAP device driver, 1.6
- [ 2.725591] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
- [ 2.731523] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
- [ 2.737670] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
- [ 2.744782] igb: Copyright (c) 2007-2014 Intel Corporation.
- [ 2.750553] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
- [ 2.758581] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
- [ 2.764704] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 5 .1.0-k
- [ 2.772557] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
- [ 2.778713] ixgbevf: Intel(R) 10 Gigabit PCI Express Virtual Function Network Driver - version 4.1.0-k
- [ 2.788234] ixgbevf: Copyright (c) 2009 - 2015 Intel Corporation.
- [ 2.794627] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI
- [ 2.801903] ixgb: Copyright (c) 1999-2008 Intel Corporation.
- [ 2.808021] libphy: orion_mdio_bus: probed
- [ 2.813564] mvneta d0030000.ethernet eth0: Using device tree mac address 00:5 1:82:11:22:00
- [ 2.822127] sky2: driver version 1.30
- [ 2.826321] VFIO - User Level meta-driver version: 0.3
- [ 2.832177] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 2.838868] ehci-pci: EHCI PCI platform driver
- [ 2.843436] ehci-platform: EHCI generic platform driver
- [ 2.848856] ehci-orion: EHCI orion driver
- [ 2.853089] orion-ehci d005e000.usb: EHCI Host Controller
- [ 2.858593] orion-ehci d005e000.usb: new USB bus registered, assigned bus num ber 1
- [ 2.866890] orion-ehci d005e000.usb: irq 13, io mem 0xd005e000
- [ 2.887015] orion-ehci d005e000.usb: USB 2.0 started, EHCI 1.00
- [ 2.893179] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bc dDevice= 4.19
- [ 2.901648] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
- [ 2.909056] usb usb1: Product: EHCI Host Controller
- [ 2.914072] usb usb1: Manufacturer: Linux 4.19.20-mvebu64 ehci_hcd
- [ 2.920435] usb usb1: SerialNumber: d005e000.usb
- [ 2.925688] hub 1-0:1.0: USB hub found
- [ 2.929497] hub 1-0:1.0: 1 port detected
- [ 2.933833] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 2.940146] ohci-pci: OHCI PCI platform driver
- [ 2.944758] ohci-platform: OHCI generic platform driver
- [ 2.950484] xhci-hcd d0058000.usb: xHCI Host Controller
- [ 2.955821] xhci-hcd d0058000.usb: new USB bus registered, assigned bus numbe r 2
- [ 2.964227] xhci-hcd d0058000.usb: hcc params 0x0a000998 hci version 0x100 qu irks 0x0000000000010010
- [ 2.973617] xhci-hcd d0058000.usb: irq 12, io mem 0xd0058000
- [ 2.979688] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bc dDevice= 4.19
- [ 2.988135] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
- [ 2.993289] ata1: SATA link down (SStatus 0 SControl 300)
- [ 2.995567] usb usb2: Product: xHCI Host Controller
- [ 2.995572] usb usb2: Manufacturer: Linux 4.19.20-mvebu64 xhci-hcd
- [ 3.012499] usb usb2: SerialNumber: d0058000.usb
- [ 3.017729] hub 2-0:1.0: USB hub found
- [ 3.021536] hub 2-0:1.0: 1 port detected
- [ 3.025816] xhci-hcd d0058000.usb: xHCI Host Controller
- [ 3.031132] xhci-hcd d0058000.usb: new USB bus registered, assigned bus numbe r 3
- [ 3.039740] xhci-hcd d0058000.usb: Host supports USB 3.0 SuperSpeed
- [ 3.046250] usb usb3: We don't know the algorithms for LPM for this host, dis abling LPM.
- [ 3.054624] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bc dDevice= 4.19
- [ 3.063066] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
- [ 3.070500] usb usb3: Product: xHCI Host Controller
- [ 3.075519] usb usb3: Manufacturer: Linux 4.19.20-mvebu64 xhci-hcd
- [ 3.081879] usb usb3: SerialNumber: d0058000.usb
- [ 3.087048] hub 3-0:1.0: USB hub found
- [ 3.090841] hub 3-0:1.0: 1 port detected
- [ 3.095346] usbcore: registered new interface driver usb-storage
- [ 3.101798] mousedev: PS/2 mouse device common for all mice
- [ 3.107786] i2c /dev entries driver
- [ 3.111453] IR NEC protocol handler initialized
- [ 3.116045] IR RC5(x/sz) protocol handler initialized
- [ 3.121235] IR RC6 protocol handler initialized
- [ 3.125896] IR JVC protocol handler initialized
- [ 3.130663] IR Sony protocol handler initialized
- [ 3.135339] IR SANYO protocol handler initialized
- [ 3.140176] IR Sharp protocol handler initialized
- [ 3.145019] IR MCE Keyboard/mouse protocol handler initialized
- [ 3.151017] IR XMP protocol handler initialized
- [ 3.156326] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: dm-d evel@redhat.com
- [ 3.165273] sdhci: Secure Digital Host Controller Interface driver
- [ 3.171567] sdhci: Copyright(c) Pierre Ossman
- [ 3.176041] sdhci-pltfm: SDHCI platform and OF driver helper
- [ 3.182117] xenon-sdhci d00d0000.sdhci: Got CD GPIO
- [ 3.211789] mmc0: SDHCI controller on d00d8000.sdhci [d00d8000.sdhci] using A DMA
- [ 3.219959] ledtrig-cpu: registered to indicate activity on CPUs
- [ 3.226522] usbcore: registered new interface driver usbhid
- [ 3.232226] usbhid: USB HID core driver
- [ 3.237334] NET: Registered protocol family 10
- [ 3.242893] Segment Routing with IPv6
- [ 3.246723] NET: Registered protocol family 17
- [ 3.251316] Key type dns_resolver registered
- [ 3.256414] registered taskstats version 1
- [ 3.260638] Loading compiled-in X.509 certificates
- [ 3.267251] Btrfs loaded, crc32c=crc32c-generic
- [ 3.274027] d0012000.serial: ttyMV0 at MMIO 0xd0012000 (irq = 0, base_baud = 1562500) is a mvebu-uart
- [ 3.283528] console [ttyMV0] enabled
- [ 3.283528] console [ttyMV0] enabled
- [ 3.290850] bootconsole [ar3700_uart0] disabled
- [ 3.290850] bootconsole [ar3700_uart0] disabled
- [ 3.301299] xenon-sdhci d00d0000.sdhci: Got CD GPIO
- [ 3.303722] xenon-sdhci d00d0000.sdhci: Linked as a consumer to regulator.1
- [ 3.342495] mmc1: SDHCI controller on d00d0000.sdhci [d00d0000.sdhci] using A DMA
- [ 3.347869] hctosys: unable to open [ 3.354147] Freeing unused kernel memo ry: 640K
- [ 3.356030] Run /init as init process
- Loading, please wait...
- [ 3.408458] mmc1: new ultra high speed SDR104 SDHC card at address 0001
- [ 3.413851] mmcblk1: mmc1:0001 GB1QT 29.8 GiB
- [ 3.422594] mmcblk1: p1
- starting version 237
- [ 3.830271] mv88e6085 d0032004.mdio-mii:01: switch 0x3410 detected: Marvell 8 8E6341, revision 0
- [ 3.891776] libphy: mdio: probed
- [ 4.794297] mv88e6085 d0032004.mdio-mii:01 wan (uninitialized): PHY [!soc!int ernal-regs@d0000000!mdio@32004!switch0@1!mdio:11] driver [Marvell 88E6390]
- [ 4.882399] mv88e6085 d0032004.mdio-mii:01 lan0 (uninitialized): PHY [!soc!in ternal-regs@d0000000!mdio@32004!switch0@1!mdio:12] driver [Marvell 88E6390]
- [ 4.970512] mv88e6085 d0032004.mdio-mii:01 lan1 (uninitialized): PHY [!soc!in ternal-regs@d0000000!mdio@32004!switch0@1!mdio:13] driver [Marvell 88E6390]
- [ 4.985326] DSA: tree 0 setup
- Begin: Loading essential drivers ... done.
- Begin: Running[ 5.006305] random: fast init done
- /scripts/init-premount ... done.
- Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
- Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems
- done.
- Begin: Will now check root file system ... fsck from util-linux 2.31.1
- [/sbin/fsck.ext4 (1) -- /dev/mmcblk1p1] fsck.ext4 -a -C0 /dev/mmcblk1p1
- /dev/mmcblk1p1: recovering journal
- /dev/mmcblk1p1: Clearing orphaned inode 7546 (uid=0, gid=0, mode=0100644, size=1 663728)
- /dev/mmcblk1p1: Clearing orphaned inode 1700 (uid=0, gid=0, mode=0100644, size=1 04504)
- /dev/mmcblk1p1: Clearing orphaned inode 3690 (uid=0, gid=0, mode=0100755, size=1 98744)
- /dev/mmcblk1p1: Clearing orphaned inode 3675 (uid=0, gid=0, mode=0100755, size=1 449320)
- /dev/mmcblk1p1: Clearing orphaned inode 3672 (uid=0, gid=0, mode=0100644, size=2 150192)
- /dev/mmcblk1p1: Clearing orphaned inode 1753 (uid=0, gid=0, mode=0100644, size=2 33664)
- /dev/mmcblk1p1: Clearing orphaned inode 1697 (uid=0, gid=0, mode=0100644, size=4 71312)
- /dev/mmcblk1p1: Clearing orphaned inode 1676 (uid=0, gid=0, mode=0100644, size=2 29568)
- /dev/mmcblk1p1: clean, 34655/1774656 files, 361060/7735992 blocks
- done.
- [ 5.923319] EXT4-fs (mmcblk1p1): mounted filesystem with writeback data mode. Opts: (null)
- done.
- Begin: Running /scripts/local-bottom ... done.
- Begin: Running /scripts/init-bottom ... done.
- [ 6.314093] systemd[1]: System time before build time, advancing clock.
- [ 6.367514] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SEL INUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL + XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybr id)
- [ 6.387220] systemd[1]: Detected architecture arm64.
- Welcome to Ubuntu 18.04.2 LTS!
- [ 6.413081] systemd[1]: Set hostname to <espressobin>.
- [ 6.904394] random: systemd: uninitialized urandom read (16 bytes read)
- [ 6.909637] systemd[1]: Created slice User and Session Slice.
- [ OK ] Created slice User and Session Slice.
- [ 6.931553] random: systemd: uninitialized urandom read (16 bytes read)
- [ 6.935848] systemd[1]: Reached target Remote File Systems.
- [ OK ] Reached target Remote File Systems.
- [ 6.955261] random: systemd: uninitialized urandom read (16 bytes read)
- [ 6.959398] systemd[1]: Reached target System Time Synchronized.
- [ OK ] Reached target System Time Synchronized.
- [ 6.979831] systemd[1]: Started Dispatch Password Requests to Console Directo ry Watch.
- [ OK ] Started Dispatch Password Requests to Console Directory Watch.
- [ 7.004311] systemd[1]: Started ntp-systemd-netif.path.
- [ OK ] Started ntp-systemd-netif.path.
- [ 7.026513] systemd[1]: Created slice System Slice.
- [ OK ] Created slice System Slice.
- [ 7.043654] systemd[1]: Listening on udev Kernel Socket.
- [ OK ] Listening on udev Kernel Socket.
- [ OK ] Listening on Syslog Socket.
- [ OK ] Created slice system-serial\x2dgetty.slice.
- [ OK ] Listening on /dev/initctl Compatibility Named Pipe.
- [ OK ] Listening on Journal Socket.
- Starting Create list of required st…ce nodes for the current kernel...
- Mounting Huge Pages File System...
- [ OK ] Listening on Network Service Netlink Socket.
- Starting Load Kernel Modules...
- [ OK ] Listening on Journal Socket (/dev/log).
- Mounting Kernel Debug File System...
- Starting Set the console keyboard layout...
- [ OK ] Listening on fsck to fsckd communication Socket.
- [ OK ] Started Forward Password Requests to Wall Directory Watch.
- Starting Nameserver information manager...
- [ OK ] Reached target Slices.
- [ OK ] Listening on Journal Audit Socket.
- Starting Journal Service...
- Mounting POSIX Message Queue File System...
- [ OK ] Listening on udev Control Socket.
- Starting udev Coldplug all Devices...
- [ OK ] Reached target Local Encrypted Volumes.
- Starting Remount Root and Kernel File Systems...
- [ OK ] Reached target Swap.
- Starting Restore / save the current clock...
- [ OK ] Started Create list of required sta…vice nodes for the current kernel.
- [ OK ] Mounted Huge Pages File System.
- [ 7.487568] EXT4-fs (mmcblk1p1): re-mounted. Opts: commit=600,errors=remount- ro
- [ OK ] Started Load Kernel Modules.
- [ OK ] Mounted Kernel Debug File System.
- [ OK ] Started Journal Service.
- [ OK ] Mounted POSIX Message Queue File System.
- [ OK ] Started Remount Root and Kernel File Systems.
- [ OK ] Started Restore / save the current clock.
- [ OK ] Started Nameserver information manager.
- [ OK ] Reached target Network (Pre).
- Starting Load/Save Random Seed...
- Starting Flush Journal to Persistent Storage...
- Mounting Kernel Configuration File System...
- Starting Apply Kernel Variables...
- Starting Create Static Device Nodes in /dev...
- [ OK ] Started Load/Save Random Seed.
- [ OK ] Mounted Kernel Configuration File System.
- [ 7.830778] systemd-journald[251]: Received request to flush runtime journal from PID 1
- [ OK ] Started Apply Kernel Variables.
- [ OK ] Started Create Static Device Nodes in /dev.
- [ OK ] Started Flush Journal to Persistent Storage.
- Starting udev Kernel Device Manager...
- [ OK ] Started udev Coldplug all Devices.
- [ OK ] Started udev Kernel Device Manager.
- Starting Network Service...
- [ OK ] Started Set the console keyboard layout.
- [ OK ] Reached target Local File Systems (Pre).
- Mounting /tmp...
- [ OK ] Mounted /tmp.
- [ OK ] Reached target Local File Systems.
- Starting Create Volatile Files and Directories...
- Starting Set console font and keymap...
- Starting Raise network interfaces...
- Starting Armbian ZRAM config...
- [ OK ] Started Set console font and keymap.
- [ OK ] Started Network Service.
- Starting Wait for Network to be Configured...
- [ OK ] Started Create Volatile Files and Directories.
- Starting Network Name Resolution...
- Starting Update UTMP about System Boot/Shutdown...
- Starting Network Time Synchronization...
- [ OK ] Started Entropy daemon using the HAVEGE algorithm.
- [ OK ] Started Update UTMP about System Boot/Shutdown.
- [ OK ] Started Network Name Resolution.
- [ OK ] Started Network Time Synchronization.
- [ OK ] Reached target Host and Network Name Lookups.
- [ OK ] Started Raise network interfaces.
- [ OK ] Found device /dev/ttyMV0.
- [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
- Starting Load/Save RF Kill Switch Status...
- [ OK ] Started Load/Save RF Kill Switch Status.
- [ OK ] Started Armbian ZRAM config.
- Starting Armbian memory supported logging...
- [ OK ] Started Armbian memory supported logging.
- [ OK ] Reached target System Initialization.
- [ OK ] Started Discard unused blocks once a week.
- Starting Armbian hardware optimization...
- [ OK ] Started Message of the Day.
- Starting Armbian hardware monitoring...
- [ OK ] Started resolvconf-pull-resolved.path.
- [ OK ] Reached target Paths.
- [ OK ] Listening on D-Bus System Message Bus Socket.
- [ OK ] Reached target Sockets.
- [ OK ] Started Daily Cleanup of Temporary Directories.
- [ OK ] Started Daily apt download activities.
- [ OK ] Started Daily apt upgrade and clean activities.
- [ OK ] Reached target Timers.
- [ OK ] Started Armbian hardware optimization.
- [ OK ] Started Armbian hardware monitoring.
- [ OK ] Reached target Basic System.
- [ OK ] Started ntp-systemd-netif.service.
- [ OK ] Started Regular background program processing daemon.
- Starting Dispatcher daemon for systemd-networkd...
- Starting System Logging Service...
- Starting LSB: Load kernel modules needed to enable cpufreq scaling...
- [ OK ] Started D-Bus System Message Bus.
- Starting Network Manager...
- Starting resolvconf-pull-resolved.service...
- Starting Resets System Activity Data Collector...
- Starting Login Service...
- Starting WPA supplicant...
- [ OK ] Started System Logging Service.
- [ OK ] Started Resets System Activity Data Collector.
- [ OK ] Started Login Service.
- [ OK ] Started WPA supplicant.
- Starting Hostname Service...
- [ OK ] Started resolvconf-pull-resolved.service.
- [ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling.
- Starting LSB: set CPUFreq kernel parameters...
- [ OK ] Started Hostname Service.
- [ OK ] Started LSB: set CPUFreq kernel parameters.
- Starting LSB: Set sysfs variables from /etc/sysfs.conf...
- [ OK ] Started Network Manager.
- [ OK ] Started ntp-systemd-netif.service.
- Starting resolvconf-pull-resolved.service...
- Starting Network Manager Script Dispatcher Service...
- [ OK ] Reached target Network.
- Starting OpenBSD Secure Shell server...
- Starting Permit User Sessions...
- [ OK ] Started Unattended Upgrades Shutdown.
- Starting Network Manager Wait Online...
- [ OK ] Started resolvconf-pull-resolved.service.
- [ OK ] Started Permit User Sessions.
- [ OK ] Started Network Manager Script Dispatcher Service.
- Starting Set console scheme...
- [ OK ] Started Set console scheme.
- [ OK ] Created slice system-getty.slice.
- [ OK ] Started LSB: Set sysfs variables from /etc/sysfs.conf.
- [ OK ] Started OpenBSD Secure Shell server.
- Starting resolvconf-pull-resolved.service...
- Starting Authorization Manager...
- [ OK ] Started Dispatcher daemon for systemd-networkd.
- [ OK ] Started resolvconf-pull-resolved.service.
- [ OK ] Started Authorization Manager.
- [ OK ] Started Network Manager Wait Online.
- Starting Daily apt upgrade and clean activities...
- [ OK ] Started Daily apt upgrade and clean activities.
- [FAILED] Failed to start Wait for Network to be Configured.
- See 'systemctl status systemd-networkd-wait-online.service' for details.
- [ OK ] Reached target Network is Online.
- Starting /etc/rc.local Compatibility...
- Starting LSB: Advanced IEEE 802.11 management daemon...
- [ OK ] Started /etc/rc.local Compatibility.
- [ OK ] Started LSB: Advanced IEEE 802.11 management daemon.
- [ OK ] Started Getty on tty1.
- [ OK ] Started Serial Getty on ttyMV0.
- [ OK ] Reached target Login Prompts.
- [ OK ] Reached target Multi-User System.
- [ OK ] Reached target Graphical Interface.
- Starting Update UTMP about System Runlevel Changes...
- [ OK ] Started Update UTMP about System Runlevel Changes.
- Ubuntu 18.04.2 LTS espressobin ttyMV0
- espressobin login: sri
- Password:
- _____ _ _
- | ____|___ _ __ _ __ ___ ___ ___ ___ | |__ (_)_ __
- | _| / __| '_ \| '__/ _ \/ __/ __|/ _ \| '_ \| | '_ \
- | |___\__ \ |_) | | | __/\__ \__ \ (_) | |_) | | | | |
- |_____|___/ .__/|_| \___||___/___/\___/|_.__/|_|_| |_|
- |_|
- Welcome to ARMBIAN 5.75 stable Ubuntu 18.04.2 LTS 4.19.20-mvebu64
- System load: 0.25 0.24 0.10 Up time: 2 min
- Memory usage: 11 % of 990MB IP: 192.168.1.144
- Usage of /: 4% of 30G
- [ General system configuration (beta): armbian-config ]
- sri@espressobin:~$
- sri@espressobin:~$ systemctl status systemd-networkd-wait-online.service
- ● systemd-networkd-wait-online.service - Wait for Network to be Configured
- Loaded: loaded (/lib/systemd/system/systemd-networkd-wait-online.service; ena
- Active: failed (Result: exit-code) since Thu 2019-02-28 12:39:28 UTC; 42s ago
- Docs: man:systemd-networkd-wait-online.service(8)
- Process: 317 ExecStart=/lib/systemd/systemd-networkd-wait-online (code=exited,
- Main PID: 317 (code=exited, status=1/FAILURE)
- Feb 28 12:38:37 espressobin systemd-networkd-wait-online[317]: managing: lan1
- Feb 28 12:38:37 espressobin systemd-networkd-wait-online[317]: managing: wan
- Feb 28 12:39:20 espressobin systemd-networkd-wait-online[317]: managing: lan0
- Feb 28 12:39:20 espressobin systemd-networkd-wait-online[317]: ignoring: lo
- Feb 28 12:39:20 espressobin systemd-networkd-wait-online[317]: managing: lan1
- Feb 28 12:39:20 espressobin systemd-networkd-wait-online[317]: managing: wan
- Feb 28 12:39:28 espressobin systemd-networkd-wait-online[317]: Event loop failed
- Feb 28 12:39:28 espressobin systemd[1]: systemd-networkd-wait-online.service: Ma
- Feb 28 12:39:28 espressobin systemd[1]: systemd-networkd-wait-online.service: Fa
- Feb 28 12:39:28 espressobin systemd[1]: Failed to start Wait for Network to be C
Add Comment
Please, Sign In to add comment