U-Boot 2009.11(Dell) (Apr 06 2014 - 08:44:55)
Built by build at Unknown host on Sun Apr  6  8:44:54 2014
S4810 Boot selector Label 1.2.0.5

CPU0:  P2020E, Version: 2.1, (0x80ea0021)
Core:  E500, Version: 5.1, (0x80211051)
Clock Configuration:
       CPU0:1200 MHz, CPU1:1200 MHz,
       CCB:600  MHz,
       DDR:396  MHz (792 MT/s data rate) (Asynchronous), LBC:37.500 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
Board: S4810 Dell Inc.
Cpld: S4810 cpld Rev 7
Cpld: Board Revision 2
Cpld: Board Type 1
I2C:   ready
DRAM:  Initializing....    DDR:  2 GB (DDR3, 64-bit, CL=6, ECC off)
FLASH: 128 MB
L2:    512 KB enabled
MMC:  FSL_ESDHC: 0
CPLD: HW Watchdog enabled
    eTSEC2 is in sgmii mode.
    eTSEC3 is in sgmii mode.

    PCIE1 used as Root Complex (base addr e000a000)
               Scanning PCI bus 01
        01  00  14e4  b845  0200  00
    PCIE1 on bus 00 - 01

In:    serial
Out:   serial
Err:   serial
Net:   eTSEC3: PHY is Broadcom BCM5461S (2060c1)
eTSEC3
Hit Esc key to interrupt autoboot:  0
Booting primary bootline....
f8000000
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at fb2600f0 ...
   Image Name:   netbsd
   Image Type:   PowerPC NetBSD Kernel Image (gzip compressed)
   Data Size:    11069299 Bytes = 10.6 MB
   Load Address: 00100040
   Entry Point:  00100040
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
CPLD: HW Watchdog disabled
## Transferring control to NetBSD stage-2 loader (at address 00100040) ...
 initppc(0x100040, 0x3902000, 0x7df6ffb0, 0x0, 0x7ffacef8, 0x7ffacef8)<enter> pi
xis_spd=0xe8 sysclk=0 pixis_sysclk=33333333 porpllsr=0x4444180c sys_clk=10000000
0 comcnfreq=600000000 openpic-reset(ctpr=15) cache(DC=32KB/32,IC=32KB/32) bptr=0
 memprobe=2048MB e500_tlbinit(0x3902000,2048MB) hid0=0x80004080/0x80804080 hid1=
0x44003040 pordevsr=0x83783c40 devdisr=0x6080000 msgbuf=0x7fffe000 exception_ini
t=0xe64d9c uvm_page_physload(0x3902,0x7fffd,0x3902,0x7fffd,0) kern_segtab=0x3902
000powerpc_fixup_stubs: 1634 fixups done in 3810541 cycles
Loaded initial symtab at 0x131a64c, strtab at 0x13dabdc, # entries 49143
 initppc done!
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.


Dell Networking OS Release 9.9(0.0P14)
 NetBSD 5.1_STABLE (MPC4810) #0: Tue May  3 01:00:29 PDT 2016
total memory = 2048 MB
avail memory = 1952 MB
mainbus0 (root)
cpunode0 at mainbus0 node 0
cpunode0: 512KB/32B 8-banked 8-way unified L2 cache
cpu0 at cpunode0 instance 1
cpu0: 1.20 GHz P2020E 2.1 with an e500v2 5.1 core, ID 0 (Primary)
cpu0: 32KB/32B 8-way L1 data cache
cpu0: 32KB/32B 8-way L1 instruction cache
cpu0: 2 TLBs, 3 concurrent 8-bit PIDs (256 total)
cpu0: tlb0: 512 fixed-size (4KB) 4-way set associative entries
cpu0: tlb1: 16 variable-size (4KB..4GB) fully associative entries
cpu1 at cpunode0 instance 2
cpu1: disabled (uniprocessor kernel)
obio0 at cpunode0: 2 of 8 ports enabled
obio0: cs0: 128MB 16-bit GPCM region at 0xf8000000
obio0: cs3: 32KB 8-bit GPCM region at 0xefdf0000
bootflash0 at obio0 cs 0 addr 0xf8000000 size 0x8000000Flash Start Base-address
f324f000

flash TESTING starts
: Virt addr: 0xf324f000: STRATA-P33 128MB bootflash
cpld0 at obio0 cs 3 addr 0xefdf0000 size 0x8000wdog at cpunode0 not configured
duart0 at cpunode0: 2 ports
com0 at duart0 port 1: ns16550a, working fifo
com0: console
com1 at duart0 port 2: ns16550a, working fifo
duart0: interrupting on irq 26
tsec0 at cpunode0 instance 1: mac-address unknown
tsec at cpunode0 instance 2 not configured
tsec2 at cpunode0 instance 3 phy 1

tsec2: Ethernet address 00:01:e8:8c:01:1d
brgphy0 at tsec2 phy 1: BCM5461 1000BASE-T media interface, rev. 1
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FD
X, auto
mpc_gpio0 at cpunode0
gpio: interrupting on LVL31 (gpio)
l2ecc0 at cpunode0 interrupting on irq 0
ddrc0 at cpunode0: ECC disabled
pq3pcie0 at cpunode0 instance 1: PCI-Express x2 controller
pci0 at pq3pcie0 bus 0
ppb0 at pci0: Freescale Semiconductor product 0x0070 (rev. 0x21)
pci1 at ppb0 bus 1
nbsd_kbde0 at pci1: BCM56845 Trident Switch ASIC, rev. 5
PCI_COMMAND_STATUS_REG VALUE :1048582
BCM device 47173 and revision 5
THIS IS 64 BIT ADDR SPACE
PCI_BAR_LOW :80000004 -- MEMORY MAPPED  PCI_BAR_HIGH:0
Address : 0x80000004    Address1 : 0x00000000
Mask    : 0xfffc0004    Mask1    : 0xffffffff
PCI BUS HANDLE:80000000  TAG:0xf317d218  ADDR:80000000   SIZE:40000
MEM TAG OF BSC 0xf317d218       VADDR PTR: (0x80000000)
INT REG:00000100

enter :kbde_dmamem_alloc
kva=0xfb263000/0x1000000,map=0xe30440a0,nsegs=1,pa=6000000/1000000
DMA VBASE:0xfb263000     DMA PBASE:6000000
pcie at cpunode0 instance 2 not configured
pcie at cpunode0 instance 3 not configured
diic0 at cpunode0: 2 ports
iic0 at diic0: I2C bus
i2cctl0 at iic0
strtc0 at iic0 addr 0x68 : M41ST84 Real-time Clock/NVRAM
s2eeprom0 at iic0 addr 0x52 : eeprom self s2eeprom0 parent iic0 tag 0xf3118810 t
ype 0x0
s2eeprom1 at iic0 addr 0x54 : eeprom self s2eeprom1 parent iic0 tag 0xf3118810 t
ype 0x0
Caching Technique enabled and allocated Memory=400
s2eeprom1: Device
s2eeprom5 at iic0 addr 0x50 : eeprom self s2eeprom5 parent iic0 tag 0xf3118810 t
ype 0x0
Caching Technique enabled and allocated Memory=400
s2eeprom5: Device
iic1 at diic0: I2C bus
i2cctl1 at iic1
tmp75x0 at iic1 addr 0x49 tmp75x1 at iic1 addr 0x4a tmp75x2 at iic1 addr 0x4d tm
p75x3 at iic1 addr 0x4c s2eeprom2 at iic1 addr 0x54 : eeprom self s2eeprom2 pare
nt iic1 tag 0xf311886c type 0x0
Caching Technique enabled and allocated Memory=400
s2eeprom2: Device
s2eeprom3 at iic1 addr 0x50 : eeprom self s2eeprom3 parent iic1 tag 0xf311886c t
ype 0x0
Caching Technique enabled and allocated Memory=400
s2eeprom3: Device
max6651x0 at iic1 addr 0x48 max6651x1 at iic1 addr 0x4b max6651x2 at iic1 addr 0
x1b max6651x3 at iic1 addr 0x1f ltc4215x0 at iic1 addr 0x42 ltc4215x1 at iic1 ad
dr 0x40 smb309x0 at iic1 addr 0x20 smb309x:  addr: 0x20
ehci0 at cpunode0 instance 1: USB controller
spi at cpunode0 not configured
sdhc0 at cpunode0: SDHC controller (DMA enabled)
sdhc0: interrupting on irq 56
sdhc0: SD Host Specification 2.0, rev.1
sdhc0: using DMA transfer
sdmmc0 at sdhc0 slot 0
sdmmc0: attach card
ld0 at sdmmc0mid=0x74 oid=0x4a45 pnm="SD   " rev=0x10 psn=0x00000000 mdt=0e7
: <SD   >
ld0: 7832 MB, 3978 cyl, 64 head, 63 sec, 512 bytes/sect x 16039936 sectors
ld0: 4-bit width, bus clock 25.000 MHz
nbsd_ubde pseudo-device
bcnp pseudo-device
bcmw pseudo-device
bcmwstk pseudo-device
bcmws pseudo-device
Too many symbols for tree, skipping 16376 symbols
ust pseudo device
sierradiag as pseudo-device
crshntfy pseudo-device
bfd pseudo-device
bshell pseudo-device
f10logger as pseudo-device getting attached
sfpx pseudo-device
f10mc pseudo-device
platform pseudo-device
root on md0a dumps on md0b
mountroot: trying ffs...
root file system type: ffs
WARNING: clock gained 625 days
WARNING: CHECK AND RESET THE DATE!
ignoring SIGQUIT SIGTSTP and SIGINFO
add net 127.0.0.0: gateway 127.0.0.1
Reading Release Image at 0x3260000 Part: B
Size of ReleaseImage is 50954904 Bytes


RELEASE IMAGE HEADER DATA :
--------------------------
Release Image SW Image Count : 3
Release Image Major-Version  : 9
Release Image Minor Version  : 9
Release Image Maint Version  : 0
Release Image Patch-Version  : 0
Release Image Header Size    : 140
Release Image Data Size      : 50954764
Release Image Platform Type  : 8
Release Image Product Name   : FTOS-SE
Release Image Checksum Value : 0x5dff28f7
Release Image Header Checksum: 0x366d2cd2
Release Image Create Year    : 2016
Release Image Create Month   : 5
Release Image Create Date    : 3
Release Image Create Hour    : 1
Release Image Create Minute  : 1
Release Image Create Second  : 58

SOFTWARE IMAGE HEADER DATA :
----------------------------
Software Image[1] Major Version : 9
Software Image[1] Minor Version : 9
Software Image[1] Maint Version : 0
Software Image[1] Patch Version : 0
Software Image[1] Image type    : 2
Software Image[1] Header Size   : 100
Software Image[1] Img Data Size : 11069380
Software Image[1] Img Orig Size : 11069380
Software Image[1] Family Code   : cp
Software Image[1] Img file Name : CPRPLP-RPM-AP-9.9.0.0P14.bin
Software Image[1] Hdr Checksum  : 0xfa6898d0
Software Image[1] Data Checksum : 0x63104a89

SOFTWARE IMAGE HEADER DATA :
----------------------------
Software Image[2] Major Version : 9
Software Image[2] Minor Version : 9
Software Image[2] Maint Version : 0
Software Image[2] Patch Version : 0
Software Image[2] Image type    : 2
Software Image[2] Header Size   : 100
Software Image[2] Img Data Size : 21880456
Software Image[2] Img Orig Size : 66785296
Software Image[2] Family Code   : nbsdpcprplp
Software Image[2] Img file Name : NBSDPCPRPLP-RPM-AP-9.9.0.0P14.bin
Software Image[2] Hdr Checksum  : 0x89d3e3d8
Software Image[2] Data Checksum : 0xd6c00a69

SOFTWARE IMAGE HEADER DATA :
----------------------------
Software Image[3] Major Version : 9
Software Image[3] Minor Version : 9
Software Image[3] Maint Version : 0
Software Image[3] Patch Version : 0
Software Image[3] Image type    : 2
Software Image[3] Header Size   : 100
Software Image[3] Img Data Size : 18004628
Software Image[3] Img Orig Size : 40837136
Software Image[3] Family Code   : nbsdlibcp
Software Image[3] Img file Name : NBSDLIBCP-RPM-AP-9.9.0.0P14.bin
Software Image[3] Hdr Checksum  : 0x66b25af8
Software Image[3] Data Checksum : 0xb8cff66c
Setting throttling levels...
netbsd:throttle_count           0x1 = 0x6

netbsd:orange           0xc = 0xa

netbsd:red              0x20 = 0x10

...Done
** /dev/rld0g
** Last Mounted on /usr/pkg
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
10636 files, 130904 used, 2181543 free (3015 frags, 272316 blocks, 0.1% fragment
ation)

MARK FILE SYSTEM CLEAN? yes


***** FILE SYSTEM MARKED CLEAN *****

***** FILE SYSTEM WAS MODIFIED *****
Starting Dell Networking OS


Jan 18 13:38:30: %STKUNIT0-M:CP %RAM-6-ELECTION_ROLE: Stack-unit 0 is transition
ing to Management Stack-unit.
Jan 18 13:38:31: %STKUNIT0-M:CP %CRYPTO-5-FIPS_SELF_TEST_PASSED: [sysd] FIPS cry
pto module self-test passed
Jan 18 13:38:31: %STKUNIT0-M:CP %CHMGR-5-STACKUNIT_DETECTED: stack-unit 0 presen
t
Jan 18 13:38:32: %STKUNIT0-M:CP %CHMGR-5-CHECKIN: Checkin from stack-unit 0 (typ
e S4810, 64 ports)
Jan 18 13:38:33: %STKUNIT0-M:CP %CHMGR-0-PS_UP: Power supply 0 in unit 0 is up
Jan 18 13:38:33: %STKUNIT0-M:CP %CHMGR-0-PS_UP: Power supply 1 in unit 0 is up
Jan 18 13:38:35: %STKUNIT0-M:CP %CHMGR-5-STACKUNIT_UP: stack-unit 0 is up
Jan 18 13:38:35: %STKUNIT0-M:CP %CHMGR-2-SYSTEM_READY: System ready



This device is configured to enter Bare Metal Provisioning (BMP).
BMP will now attempt to download an image, configuration file or boot script usi
ng DHCP.

Jan 18 13:38:50: %STKUNIT0-M:CP %RAM-5-STACKUNIT_STATE: Stack-unit 0 is in Activ
e State.
Jan 18 13:38:51: %STKUNIT0-M:CP %CRYPTO-5-FIPS_SELF_TEST_PASSED: [bmp] FIPS cryp
to module self-test passed


This device is in Bare Metal Provisioning (BMP) mode.
BMP is attempting to download an image, configuration file or boot script using
DHCP.

To continue with the standard manual interactive mode, it is necessary to abort
BMP.
Press A to abort BMP now.
Press C to continue with BMP.
Press L to toggle BMP syslog and console messages.
Press S to display the BMP status.
[A/C/L/S]:% Warning: The bmp process will stop ...
Jan 18 13:42:34: %STKUNIT0-M:CP %SYS-5-CONFIG_LOAD: Loading configuration file
Jan 18 13:42:34: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Ma 11/0
Jan 18 13:42:34: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Ma 10/0
Jan 18 13:42:34: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Ma 9/0
Jan 18 13:42:34: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Ma 8/0
Jan 18 13:42:34: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Ma 7/0
Jan 18 13:42:35: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Ma 6/0
Jan 18 13:42:35: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Ma 5/0
Jan 18 13:42:35: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Ma 4/0
Jan 18 13:42:36: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Ma 3/0
Jan 18 13:42:36: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Ma 2/0
Jan 18 13:42:36: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Ma 1/0
Jan 18 13:42:36: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Ma 0/0
Jan 18 13:42:36: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Fo 0/60
Jan 18 13:42:36: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Fo 0/56
Jan 18 13:42:36: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Fo 0/52
Jan 18 13:42:36: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Fo 0/48
Jan 18 13:42:36: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/47
Jan 18 13:42:37: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/46
Jan 18 13:42:37: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/45
Jan 18 13:42:37: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/44
Jan 18 13:42:37: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/43
Jan 18 13:42:37: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/42
Jan 18 13:42:37: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/41
Jan 18 13:42:37: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/40
Jan 18 13:42:37: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/39
Jan 18 13:42:38: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/38
Jan 18 13:42:38: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/37
Jan 18 13:42:38: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/36
Jan 18 13:42:38: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/35
Jan 18 13:42:38: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/34
Jan 18 13:42:38: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/33
Jan 18 13:42:38: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/32
Jan 18 13:42:38: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/31
Jan 18 13:42:38: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/30
Jan 18 13:42:39: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/29
Jan 18 13:42:39: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/28
Jan 18 13:42:39: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/27
Jan 18 13:42:39: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/26
Jan 18 13:42:39: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/25
Jan 18 13:42:39: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/24
Jan 18 13:42:39: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/23
Jan 18 13:42:39: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/22
Jan 18 13:42:39: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/21
Jan 18 13:42:40: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/20
Jan 18 13:42:40: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/19
Jan 18 13:42:40: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/18
Jan 18 13:42:40: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/17
Jan 18 13:42:41: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/16
Jan 18 13:42:41: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/15
Jan 18 13:42:41: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/14
Jan 18 13:42:41: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/13
Jan 18 13:42:41: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/12
Jan 18 13:42:41: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/11
Jan 18 13:42:42: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/10
Jan 18 13:42:42: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/9
Jan 18 13:42:42: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/8
Jan 18 13:42:42: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/7
Jan 18 13:42:42: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/6
Jan 18 13:42:42: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/5
Jan 18 13:42:43: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/4
Jan 18 13:42:43: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/3
Jan 18 13:42:43: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/2
Jan 18 13:42:43: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/1
Jan 18 13:42:43: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface Admin stat
e to down: Te 0/0
Jan 18 13:42:43: %STKUNIT0-M:CP %SYS-5-CONFIG_LOAD: Loading configuration file
Jan 18 13:42:43: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface Admin stat
e to up: Ma 0/0
Jan 18 13:42:43: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface Admin stat
e to up: Ma 1/0
Jan 18 13:42:44: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface Admin stat
e to up: Ma 2/0
Jan 18 13:42:44: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface Admin stat
e to up: Ma 3/0
Dell-BMP>Jan 18 13:42:44: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface A
dmin state to up: Ma 4/0
Jan 18 13:42:44: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface Admin stat
e to up: Ma 5/0
Jan 18 13:42:44: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface Admin stat
e to up: Ma 6/0
Jan 18 13:42:44: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface Admin stat
e to up: Ma 7/0
Jan 18 13:42:45: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface Admin stat
e to up: Ma 8/0
Jan 18 13:42:45: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface Admin stat
e to up: Ma 9/0
Jan 18 13:42:45: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface Admin stat
e to up: Ma 10/0
Jan 18 13:42:45: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface Admin stat
e to up: Ma 11/0
Jan 18 13:42:45: %STKUNIT0-M:CP %SEC-5-LOGIN_SUCCESS: Login successful on consol
e
Jan 18 13:42:45: %STKUNIT0-M:CP %SYS-5-CONFIG_I: Configured from  EOA0
Jan 18 13:42:48: %STKUNIT0-M:CP %BMP-5-PROCESS_COMPLETED: BMP process is complet
e. The configuration/script must be saved in order to use it after subsequent re
loads

Dell>en


 The SupportAssist EULA acceptance option has not been selected. SupportAssist
 can be enabled once the SupportAssist EULA has been accepted. Use the:
'support-assist activate' command to accept EULA and enable SupportAssist.

Dell#Jan 18 13:43:08: %STKUNIT0-M:CP %SEC-4-ENABLE_PASSW_NOT_CONFIGURED: Enable
password is required for authentication but not configured (by default from cons
ole)
Jan 18 13:43:08: %STKUNIT0-M:CP %SEC-5-AUTHENTICATION_ENABLE_SUCCESS: Enable aut
hentication success  on console

Dell#show version
Dell Real Time Operating System Software
Dell Operating System Version:  2.0
Dell Application Software Version:  9.9(0.0P14)
Copyright (c) 1999-2015 by Dell Inc. All Rights Reserved.
Build Time: Mon May  2 23:54:01 2016
Build Path: /sites/eqx/work/swbuild01_1/patch03/E9-9-0/SW/SRC
Dell Networking OS uptime is 4 minute(s)

System image file is "system://B"

System Type: S4810
Control Processor: Freescale QorIQ P2020 with 2 Gbytes (2147483648 bytes) of mem
ory, core(s) 1.

128M bytes of boot flash memory.

  1 52-port GE/TE/FG (SE)
 48 Ten GigabitEthernet/IEEE 802.3 interface(s)
  4 Forty GigabitEthernet/IEEE 802.3 interface(s)
Dell#