Boot (PRI)-> tftp 0x89000000
dup 1 speed 1000
*** Warning: no boot file name; using '0101A8C0.img'
Using eth0 device
TFTP from server 192.168.1.10; our IP address is 192.168.1.1
Filename '0101A8C0.img'.
Load address: 0x89000000
Loading: *#################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 #################################################################
 ###############################
done
Bytes transferred = 3817134 (3a3eae hex)
Boot (PRI)-> bootm
## Booting image at 89000000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.180
   Created:      2020-05-16  18:32:20 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3817070 Bytes =  3.6 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 4.14.180 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11063-85e04e9f46)) #0 Sat May 16 18:32:20 2020
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is OCEDO Koala
[    0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 10000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] random: get_random_bytes called from 0x804ff740 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 246340K/262144K available (4030K kernel code, 162K rwdata, 532K rodata, 8132K init, 212K bss, 15804K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 720.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[    0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[    0.008295] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[    0.074984] pid_max: default: 32768 minimum: 301
[    0.080065] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.087103] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.098076] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.108576] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.115127] pinctrl core: initialized pinctrl subsystem
[    0.122559] NET: Registered protocol family 16
[    0.129782] PCI host bridge /ahb/pcie-controller@180c0000 ranges:
[    0.136311]  MEM 0x0000000010000000..0x0000000011ffffff
[    0.141868]   IO 0x0000000000000000..0x0000000000000000
[    0.160481] PCI host bridge to bus 0000:00
[    0.164849] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[    0.172196] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.178124] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.185351] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.194196] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[    0.202019] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[    0.212052] clocksource: Switched to clocksource MIPS
[    0.218253] NET: Registered protocol family 2
[    0.223634] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.231072] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.237894] TCP: Hash tables configured (established 2048 bind 2048)
[    0.244777] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.251003] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.257901] NET: Registered protocol family 1
[    0.399494] Crashlog allocated RAM at address 0x3f00000
[    0.406245] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[    0.417176] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.423413] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.489455] io scheduler noop registered
[    0.493662] io scheduler deadline registered (default)
[    0.500920] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68
[    0.509226] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.517932] console [ttyS0] disabled
[    0.521762] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 2500000) is a 16550A
[    0.530975] console [ttyS0] enabled
[    0.530975] console [ttyS0] enabled
[    0.538399] bootconsole [early0] disabled
[    0.538399] bootconsole [early0] disabled
[    0.554056] m25p80 spi0.0: s25fl512s (65536 Kbytes)
[    0.559051] 7 fixed-partitions partitions found on MTD device spi0.0
[    0.565535] Creating 7 MTD partitions on "spi0.0":
[    0.570404] 0x000000000000-0x000000040000 : "u-boot"
[    0.576102] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.582141] 0x000000050000-0x000000790000 : "firmware"
[    0.593240] 0x000000790000-0x000000ed0000 : "vendor"
[    0.598901] 0x000000ed0000-0x000000fe0000 : "data"
[    0.604416] 0x000000fe0000-0x000000ff0000 : "id"
[    0.609717] 0x000000ff0000-0x000001000000 : "art"
[    0.616030] libphy: Fixed MDIO Bus: probed
[    0.630504] ag71xx 19000000.eth: invalid MAC address, using random address
[    0.973737] libphy: ag71xx_mdio: probed
[    1.092671] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:05 [uid=004dd072, driver=Atheros 8035 ethernet]
[    1.103425] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii-rxid
[    1.112018] NET: Registered protocol family 10
[    1.120443] Segment Routing with IPv6
[    1.124288] NET: Registered protocol family 17
[    1.128829] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.141984] 8021q: 802.1Q VLAN Support v1.8
[    1.147569] hctosys: unable to open rtc device (rtc0)
[    1.181851] Freeing unused kernel memory: 8132K
[    1.186471] This architecture does not have kernel memory protection.
[    1.205328] init: Console is alive
[    1.208953] init: - watchdog -
[    1.228484] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    1.237294] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    1.245775] init: - preinit -
[    1.422935] random: jshn: uninitialized urandom read (4 bytes read)
[    1.499934] random: jshn: uninitialized urandom read (4 bytes read)
[    1.533104] random: jshn: uninitialized urandom read (4 bytes read)
[    1.693847] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    3.622052] random: fast init done
[    4.823605] procd: - early -
[    4.826611] procd: - watchdog -
[    5.390828] procd: - watchdog -
[    5.394296] procd: - ubus -
[    5.402674] urandom_read: 5 callbacks suppressed
[    5.402681] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.447413] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.455121] procd: - init -
Please press Enter to activate this console.
[    5.837999] kmodloader: loading kernel modules from /etc/modules.d/*
[    5.866814] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    5.887981] Loading modules backported from Linux version v4.19.120-0-gfdc072324f3c
[    5.895790] Backport generated by backports.git v4.19.120-1-0-g60c3a249
[    5.923964] ip_tables: (C) 2000-2006 Netfilter Core Team
[    5.946639] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[    6.034315] xt_time: kernel timezone is -0000
[    6.126387] PPP generic driver version 2.4.2
[    6.142775] NET: Registered protocol family 24
[    6.200918] urngd: v1.0.2 started.
[    6.210578] ath: phy0: Unable to initialize hardware; initialization status: -5
[    6.218032] ath9k 18100000.wmac: failed to initialize device
[    6.223830] ath9k: probe of 18100000.wmac failed with error -5
[    6.262375] kmodloader: done loading kernel modules from /etc/modules.d/*
[    6.368535] random: crng init done



BusyBox v1.30.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt 19.07.3, r11063-85e04e9f46
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@(none):/#
root@(none):/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/# [   24.561375] eth0: link up (1000Mbps/Full duplex)
[   24.575655] br-lan: port 1(eth0) entered blocking state
[   24.580960] br-lan: port 1(eth0) entered disabled state
[   24.586539] device eth0 entered promiscuous mode
[   24.621308] br-lan: port 1(eth0) entered blocking state
[   24.626652] br-lan: port 1(eth0) entered forwarding state
[   24.632293] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   25.632190] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready

root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#

U-Boot 1.2.0.03 (Mar 28 2016 - 20:40:29)

ap135 - Scorpion 1.0DRAM:
sri
Scorpion 1.0
ath_ddr_initial_config(205): (32bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0x3, 0x1f)
Tap values = (0x11, 0x11, 0x11, 0x11)
256 MB
Flash Manuf Id 0x1, DeviceId0 0x2, DeviceId1 0x20
flash size 64MB, sector count = 256
Flash: 64 MB
In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0xe
ath_gmac_enet_initialize: reset mask:c02200
Scorpion  ----> S17 PHY *
TEST: FINAL REG VAL after TX Calibration - 0x00000000
TEST: FINAL XMII VAL after RX Calibration - 0x00000000
TEST: FINAL ETH_CFG VAL after RX Calibration - 0x00000001
athrs17_reg_init: complete
: cfg1 0x80000000 cfg2 0x7135
eth0: d8:84:66:4f:fd:dc
eth0 up
eth0
Setting 0x18116290 to 0x60c0214f
Hit 'd' for diagnostics, or any other key to stop autoboot:  2  1  0
## Executing script at 8ff6e160
check for watchdog, limit=3...
check for reset by watchdog...
no watchdog...
bSaveEnviron=0 image_order=1 0
ready to boot kernel...
## Booting image at a0280000 ...
   Image Name:   10.41.08.0012
   Created:      2018-06-22   0:50:36 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    8532062 Bytes =  8.1 MB
   Load Address: 80002000
   Entry Point:  801d3430
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...