Bootloader Version: 10.1.05T310 (Mar 19 2015 - 16:39:59)


Model ID: 1.0.0.0.1.0

Enter 'b' to stop at boot monitor:  0
ICX64XX-boot>> printenv
baudrate=9600
ipaddr=10.21.112.143
serverip=10.21.128.241
netmask=255.255.240.0
gatewayip=10.21.112.1
uboot=kxz10105
image_name=390107fix/nofifo/swt_defClk_nophyinitdelay.bin
ver=10.1.05T310 (Mar 19 2015 - 16:39:59)
ICX64XX-boot>> printenv bootcmd
bootcmd=run defbootcmd
ICX64XX-boot>> printenv defbootcmd
defbootcmd=u_imi; cp.b $(flash_addr) $(linux_bootaddr) $(image_size); setenv bootargs ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off console=${consoledev},${baudrate} ${standalone_network_device} ${extra_bootargs} ${fips_reset} quiet;bootm $(linux_bootaddr)
ICX64XX-boot>> printenv extra_bootargs
## Error: "extra_bootargs" not defined
ICX64XX-boot>> exit
Unknown command 'exit' - try 'help'
ICX64XX-boot>>
ICX64XX-boot>>
ICX6450-24P Router>
ICX6450-24P Router>
ICX6450-24P Router>

ICX6450-24P Router>
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** BROCADE BOARD: BE (configured)



Ethernet Switch, Version


1.1.9_01T310 (Oct 20 2011 - 16:12:04)

U-Boot code: 01200000 -> 012AFFF0  BSS: -> 012E0420
IRQ Stack: 009fff7c
FIQ Stack: 009fef7c

Soc: 88F6281 A0 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 266Mhz , TClock = 166Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 15 tRCD=5
DRAM CS[0] base 0x00000000   size 512MB
DRAM Total size 512MB  16bit width
[32768kB@f8000000] Flash: 32 MB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 19M): Done

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


PEX0 interface detected no Link.
PEX 0: interface detected no Link.
CPLD Revision: 0.1.0
Hardware Revision: 0.0.1, Alpha Build
Board_ID2 Board_ID1 Board_ID0
        1         0         0
Model ID: 1.0.0.0.1.0


Board Id: PonCat2-24 PoE
Chip Revision A2
Enable temperature monitor function ... Done
Initialize IO Expander ... Done
Not do pp_init
switch to 2nd flash
2nd flash enters into 4B mode
switch to 1st flash
Initialize CPU packet ... Done
egiga0 [PRIME], port1, port2, port3, port4, port5, port6, port7, port8, port9, port10, port11, port12, port13, port14, port15, port16, port17, port18, port19, port20, port21, port22, port23, port24, port25, port26, port27, port28, ppsdma
Enter 'b' to stop at boot monitor:  0
ICX>> printenv
bootdelay=3
baudrate=9600
loads_echo=0
logname=katara_log.txt
blup=tftp 3000000 $uboot; prot off f8000000 f80fffff; erase f8000000 f80fffff; sflash write 3000000 0 $filesize
blup2=tftp 3000000 $(uboot); prot off f8000000 f80fffff; erase f8000000 f80aFFFF; sflash write 3000000 0 0xB0000
uplog=mw.l 3000000 0 300000; sflash read f9a00000 3000000 300000; tftp 3000000 $(logname) 300000
CASset=min
ethprime=egiga0
rootpath=/tftpboot/rootfs_arm-gnueabi-be
consoledev=ttyS0
linux_loadaddr=0x2000000
fix_nfsroot_to_BE=no
linux_parts=mtdparts=spi_flash:0x00100000(uboot)ro,0x001c0000(kernel),0x01d40000(rootfs)
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):off console=$(consoledev),$(baudrate) $(othbootargs) $(linux_parts); tftp $(linux_loadaddr) $(image_name);bootm $(linux_loadaddr)
standalone_mtd=setenv bootargs root=/dev/mtdblock2 rw rootfstype=jffs2 ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):off console=$(consoledev),$(baudrate) $(othbootargs) $(linux_parts); bootm 0xf8100000
netdev=eth0
vx_burn=mtdburn $(vx_image_name)
vx_image_name=vxWorks.st
vx=setenv bootargs mgi(0,0) host:VxWorks h=$(serverip) e=$(ipaddr):FFFF0000 u=anonymous pw=target; setenv bootaddr 0x700; setenv loadaddr 0x3000000; tftpboot $(loadaddr) $(vx_image_name); bootvx
vx_flash=setenv bootargs mgi(0,0) host:VxWorks h=$(serverip) e=$(ipaddr):FFFF0000 u=anonymous pw=target; setenv bootaddr 0x700; vx_unc_boot
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
ethaddr=00:50:43:60:37:1f
ethmtu=1500
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
yuk_ethaddr=00:00:00:EE:51:81
ethact=egiga0
uboot=uboot-1.1.9.bin
standalone_network_device=egiga0
image_size=0x12000
uboot_size=00000
linux_bootaddr=1ffffc0
bootcmd=u_imi; cp.b $(flash_addr) $(linux_bootaddr) $(image_size);bootm $(linux_bootaddr)
image_name=pImage
bootargs=ip=10.21.112.127:10.20.155.185:10.21.112.1:255.255.240.0:eth0:off console=ttyS0,9600 nosoftwatchdog egiga0
filesize=ba250c
fileaddr=3000000
gatewayip=10.21.112.1
netmask=255.255.240.0
ipaddr=10.21.112.127
serverip=10.20.155.185
flash_addr=f9080200
stdin=serial
stdout=serial
stderr=serial
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
disaMvPnp=no
ver=1.1.9_01T310 (Oct 20 2011 - 16:12:04)

Environment size: 2460/4092 bytes
ICX>> printenv bootcmd
bootcmd=u_imi; cp.b $(flash_addr) $(linux_bootaddr) $(image_size);bootm $(linux_bootaddr)
ICX>> printenv defbootcmd
## Error: "defbootcmd" not defined
ICX>> printenv extra_bootargs
## Error: "extra_bootargs" not defined
ICX>>