Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- uloader 2011.06.0 (May 20 2014 - 16:36:41)
- Board: Mindspeed C2000
- c2k_spi_probe
- Copying Barebox from SPI Flash(bootopt=0)
- BB Copying Done
- ## Starting Barebox at 0x01000000 ...
- barebox 2011.06.0-svn44305-dirty6 (Aug 28 2014 - 22:25:22)
- Board: Mindspeed C2000
- c2k_spi_probe
- c2k_otp_probe.
- cbus_baseaddr: 9c000000, ddr_baseaddr: 03800000, ddr_phys_baseaddr: 03800000
- class init complete
- tmu init complete
- bmu1 init: done
- bmu2 init: done
- util init complete
- GPI1 init complete
- GPI2 init complete
- HGPI init complete
- HIF rx desc: base_va: 03e80000, base_pa: 03e80000
- HIF tx desc: base_va: 03e80400, base_pa: 03e80400
- HIF init complete
- bmu1 enabled
- bmu2 enabled
- pfe_hw_init: done
- pfe_firmware_init
- pfe_load_elf
- pfe_load_elf no of sections: 10
- pfe_firmware_init: class firmware loaded
- pfe_load_elf
- pfe_load_elf no of sections: 10
- pfe_firmware_init: tmu firmware loaded
- pfe_load_elf
- pfe_load_elf no of sections: 14
- pfe_firmware_init: util firmware loaded
- eth_port: 0
- NAS540_phy_reg_setting[eth_port].phyaddr: 0x4
- miidev_restart_aneg for PHY4
- eth_port: 1
- NAS540_phy_reg_setting[eth_port].phyaddr: 0x6
- miidev_restart_aneg for PHY6
- cfi_probe: cfi_flash base: 0xc0000000 size: 0x04000000
- ## Unknown FLASH on Bank at 0xc0000000 - Size = 0x00000000 = 0 MB
- bootopt = 0x0
- Using ENV from SPI Flash.
- nand_probe: comcerto_nand base: 0xc8300000 size: 0x256 MB
- NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64
- Using default values
- Bad block table not found for chip 0
- Bad block table not found for chip 0
- Scanning device for bad blocks
- Bad block table written to 0x0ffe0000, version 0x01
- Bad block table written to 0x0ffc0000, version 0x01
- Malloc space: 0x00600000 -> 0x01000000 (size 10 MB)
- Stack space : 0x005f8000 -> 0x00600000 (size 32 kB)
- running /env/bin/init...
- Unknown command 'export' - try 'help'
- Disabling eee function of phy 4 ...
- Disabling eee function of phy 6 ...
- Hit any key to stop autoboot: 0
- booting kernel of type uimage from /dev/nand0.kernel2.bb
- Bad Header Checksum
- Failed.
- booting kernel of type uimage from /dev/nand0.kernel1.bb
- Bad Header Checksum
- warning: No MAC address set. Using random address 56:38:55:4D:6E:B1
- T DHCP client bound to address 192.168.178.145
- DHCP client bound to address 192.168.178.145
- host 192.168.178.23 is alive
- erasing partition /dev/nand0.kernel1.bb
- flashing uImage_MFG to /dev/nand0.kernel1.bb
- TFTP from server 192.168.178.23 ('uImage_MFG' -> '/dev/nand0.kernel1.bb')
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- ###############################################################
- T DHCP client bound to address 192.168.178.145
- host 192.168.178.23 is alive
- erasing partition /dev/nand0.kernel2.bb
- flashing uImage_MFG to /dev/nand0.kernel2.bb
- TFTP from server 192.168.178.23 ('uImage_MFG' -> '/dev/nand0.kernel2.bb')
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- ###############################################################
- uloader 2011.06.0 (May 20 2014 - 16:36:41)
- Board: Mindspeed C2000
- c2k_spi_probe
- Copying Barebox from SPI Flash(bootopt=0)
- BB Copying Done
- ## Starting Barebox at 0x01000000 ...
- barebox 2011.06.0-svn44305-dirty6 (Aug 28 2014 - 22:25:22)
- Board: Mindspeed C2000
- c2k_spi_probe
- c2k_otp_probe.
- cbus_baseaddr: 9c000000, ddr_baseaddr: 03800000, ddr_phys_baseaddr: 03800000
- class init complete
- tmu init complete
- bmu1 init: done
- bmu2 init: done
- util init complete
- GPI1 init complete
- GPI2 init complete
- HGPI init complete
- HIF rx desc: base_va: 03e80000, base_pa: 03e80000
- HIF tx desc: base_va: 03e80400, base_pa: 03e80400
- HIF init complete
- bmu1 enabled
- bmu2 enabled
- pfe_hw_init: done
- pfe_firmware_init
- pfe_load_elf
- pfe_load_elf no of sections: 10
- pfe_firmware_init: class firmware loaded
- pfe_load_elf
- pfe_load_elf no of sections: 10
- pfe_firmware_init: tmu firmware loaded
- pfe_load_elf
- pfe_load_elf no of sections: 14
- pfe_firmware_init: util firmware loaded
- eth_port: 0
- NAS540_phy_reg_setting[eth_port].phyaddr: 0x4
- miidev_restart_aneg for PHY4
- eth_port: 1
- NAS540_phy_reg_setting[eth_port].phyaddr: 0x6
- miidev_restart_aneg for PHY6
- cfi_probe: cfi_flash base: 0xc0000000 size: 0x04000000
- ## Unknown FLASH on Bank at 0xc0000000 - Size = 0x00000000 = 0 MB
- bootopt = 0x0
- Using ENV from SPI Flash.
- nand_probe: comcerto_nand base: 0xc8300000 size: 0x256 MB
- NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64
- Using default values
- Bad block table not found for chip 0
- Bad block table not found for chip 0
- Scanning device for bad blocks
- Bad block table written to 0x0ffe0000, version 0x01
- Bad block table written to 0x0ffc0000, version 0x01
- Malloc space: 0x00600000 -> 0x01000000 (size 10 MB)
- Stack space : 0x005f8000 -> 0x00600000 (size 32 kB)
- running /env/bin/init...
- Unknown command 'export' - try 'help'
- Disabling eee function of phy 4 ...
- Disabling eee function of phy 6 ...
- Hit any key to stop autoboot: 1
- booting kernel of type uimage from /dev/nand0.kernel2.bb
- Verifying Checksum ... OK
- Image Name: Linux-3.2.54
- Created: 2018-05-21 17:36:47 UTC
- Image Type: <NULL> <NULL> <NULL> (<NULL>)
- Data Size: 7311656 Bytes = 7 MB
- Load Address: 0f008000
- Entry Point: 0f008000
- OK
- Starting kernel ...
- commandline: console=ttyS0,115200n8, init=/etc/preinit pcie_gen1_only=yes mac_addr=,, ip=dhcp root=ubi0:rootfs ubi.mtd=2,2048 rootfstype=ubifs rw noinitrd mtdparts=spi0.0:256k(uloader)ro,512k(barebox)ro,256k(env);comcertonand:10M(config),10M(kernel1),110M(rootfs1),10M(kernel2),110M(rootfs2),-(reserved) usb3_internal_clk=yes
- arch_number: 1094
- Uncompressing Linux... done, booting the kernel.
- [ 0.000000] Booting Linux on physical CPU 0
- [ 0.000000] Initializing cgroup subsys cpuset
- [ 0.000000] Linux version 3.2.54 (root@SDD2SVR2) (gcc version 4.8.5 20150209 (prerelease) (crosstool-NG 1.21.0) ) #1 SMP Tue May 22 01:36:44 CST 2018
- [ 0.000000] CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=50c53c7d
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000] Machine: Comcerto 2000 EVM
- [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
- [ 0.000000] Comcerto: zone_dma mapping size=2c00000 type=b
- [ 0.000000] PERCPU: Embedded 8 pages/cpu @8524c000 s9504 r8192 d15072 u32768
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 254976
- [ 0.000000] Kernel command line: console=ttyS0,115200n8, init=/etc/preinit pcie_gen1_only=yes mac_addr=,, ip=dhcp root=ubi0:rootfs ubi.mtd=2,2048 rootfstype=ubifs rw noinitrd mtdparts=spi0.0:256k(uloader)ro,512k(barebox)ro,256k(env);comcertonand:10M(config),10M(kernel1),110M(rootfs1),10M(kernel2),110M(rootfs2),-(reserved) usb3_internal_clk=yes
- [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
- [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Memory: 44MB 960MB = 1004MB total
- [ 0.000000] Memory: 1008508k/1008508k available, 40068k reserved, 0K highmem
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xfff30000 - 0xfffe0000 ( 704 kB)
- [ 0.000000] vmalloc : 0xc0800000 - 0xf0000000 ( 760 MB)
- [ 0.000000] lowmem : 0x80000000 - 0xc0000000 (1024 MB)
- [ 0.000000] modules : 0x83600000 - 0x84000000 ( 10 MB)
- [ 0.000000] .text : 0x84008000 - 0x8468b460 (6670 kB)
- [ 0.000000] .init : 0x8468c000 - 0x8499a520 (3130 kB)
- [ 0.000000] .data : 0x8499c000 - 0x849e4bb0 ( 291 kB)
- [ 0.000000] .bss : 0x849e4bd4 - 0x84a45218 ( 386 kB)
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:256
- [ 0.000000] PLL0 running at 2400 MHz, PLL1 at 1000 MHz PLL2 running at 1500 MHz PLL3 running at 1066 MHz
- [ 0.000000] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 17179ms
- [ 0.000192] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
- [ 0.090048] pid_max: default: 32768 minimum: 301
- [ 0.090247] Mount-cache hash table entries: 512
- [ 0.090777] Initializing cgroup subsys cpuacct
- [ 0.090810] Initializing cgroup subsys devices
- [ 0.090845] CPU: Testing write buffer coherency: ok
- [ 0.091008] CPU0: thread -1, cpu 0, socket 9, mpidr 80000900
- [ 0.091035] Calibrating local timer... 299.84MHz.
- [ 0.150067] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
- [ 0.151162] CPU1 powered up
- [ 0.151760] CPU1: Booted secondary processor
- [ 0.190035] CPU1: thread -1, cpu 1, socket 9, mpidr 80000901
- [ 0.190092] Brought up 2 CPUs
- [ 0.190104] SMP: Total of 2 processors activated (2393.70 BogoMIPS).
- [ 0.191624] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 2
- [ 0.192014] xor: measuring software checksum speed
- [ 0.239989] arm4regs : 2129.600 MB/sec
- [ 0.289959] 8regs : 1397.600 MB/sec
- [ 0.339932] 32regs : 1186.000 MB/sec
- [ 0.389916] neon : 1384.000 MB/sec
- [ 0.389924] xor: using function: arm4regs (2129.600 MB/sec)
- [ 0.390113] NET: Registered protocol family 16
- [ 0.391852] L310 cache controller enabled
- [ 0.391866] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x00c40000, PREFETCH_CTRL 0x00000000, Cache size: 262144 B
- [ 0.391945] ARMv7 AUX CTRL(0): 0x41
- [ 0.391950] ARMv7 AUX CTRL(0): 0x41
- [ 0.391965] ARMv7 AUX CTRL(1): 0x41
- [ 0.391973] ARMv7 AUX CTRL(1): 0x41
- [ 0.392895] Pin Select for GPIO[15:0]: 05000000
- [ 0.392902] Pin Select for GPIO[31:16]: 00555540
- [ 0.392907] Output Enable for GPIO[31:0]: DFFFFF00
- [ 0.392913] Pin Select for GPIO[59:32]: 0FFFFFFE
- [ 0.392918] Pin Select for GPIO[63:60]: 00000020
- [ 0.392923] Output Enable for GPIO[63:32]: 00000001
- [ 0.392929] Enable HD1 ...
- [ 0.392934] Enable HD3 ...
- [ 6.396740] Enable HD2 ...
- [ 6.396746] Enable HD4 ...
- [ 12.403567] Enable USB ...
- [ 12.404861] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
- [ 12.404872] hw-breakpoint: maximum watchpoint size is 4 bytes.
- [ 12.404887] Power Management Mode Support For C2000:
- [ 12.405250] PCIe: Ref clk 48Mhz
- [ 12.405257] PCIe: Detected C2K RevA1 device serdes clk devider old:new=2e:6
- [ 12.408519] PCIe0: Link Up Success
- [ 12.408526] PCIe0: Polarity: 0 Gen1 mode: 1 External Clk: 0
- [ 12.408531] comcerto_pcie_rc_int_init
- [ 12.408931] PCI: bus0: Fast back to back transfers disabled
- [ 12.409116] pci 0000:00:00.0: BAR 6: assigned [mem 0xa0000000-0xa000ffff pref]
- [ 12.409127] pci 0000:00:00.0: BAR 5: assigned [mem 0xa0010000-0xa00101ff]
- [ 12.409140] pci 0000:00:00.0: BAR 5: set to [mem 0xa0010000-0xa00101ff] (PCI address [0xa0010000-0xa00101ff])
- [ 12.435952] bio: create slab <bio-0> at 0
- [ 12.604511] raid6: int32x1 32 MB/s
- [ 12.773969] raid6: int32x2 49 MB/s
- [ 12.943717] raid6: int32x4 84 MB/s
- [ 13.113486] raid6: int32x8 119 MB/s
- [ 13.283535] raid6: neonx1 144 MB/s
- [ 13.453037] raid6: neonx2 177 MB/s
- [ 13.623105] raid6: neonx4 199 MB/s
- [ 13.792852] raid6: neonx8 201 MB/s
- [ 13.792859] raid6: using algorithm neonx8 (201 MB/s)
- [ 13.793163] vgaarb: loaded
- [ 13.793690] SCSI subsystem initialized
- [ 13.794595] usbcore: registered new interface driver usbfs
- [ 13.794819] usbcore: registered new interface driver hub
- [ 13.794978] usbcore: registered new device driver usb
- [ 13.796025] Switching to clocksource timer2
- [ 13.805780] NET: Registered protocol family 2
- [ 13.806000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 13.806849] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
- [ 13.808209] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
- [ 13.808852] TCP: Hash tables configured (established 131072 bind 65536)
- [ 13.808861] TCP reno registered
- [ 13.808873] UDP hash table entries: 512 (order: 2, 16384 bytes)
- [ 13.808927] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
- [ 13.809285] NET: Registered protocol family 1
- [ 13.809625] RPC: Registered named UNIX socket transport module.
- [ 13.809633] RPC: Registered udp transport module.
- [ 13.809638] RPC: Registered tcp transport module.
- [ 13.809644] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 14.039084] gpio_dev = fd00000
- [ 14.043388] membuf_init: created membuf device(252, 0)
- [ 14.043448] clock_frequency_set: (1:24) NTG INCR value is 422212465
- [ 14.070628] VFS: Disk quotas dquot_6.5.2
- [ 14.070796] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 14.071560] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
- [ 14.071569] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
- [ 14.072186] fuse init (API version 7.17)
- [ 14.074878] Btrfs loaded
- [ 14.074906] msgmni has been set to 1969
- [ 14.080509] async_tx: api initialized (async)
- [ 14.080964] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
- [ 14.080975] io scheduler noop registered
- [ 14.080981] io scheduler deadline registered
- [ 14.081091] io scheduler cfq registered (default)
- [ 14.084376] ### comcerto_dma_probe: XOR DMA channel registered
- [ 14.090161] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- [ 14.356504] 84a386a0 849af858 0 ffffffff
- [ 14.357315] serial8250 serial8250.0: Couldn't set LCR to 191
- [ 14.358592] serial8250 serial8250.0: Couldn't set LCR to 191
- [ 14.359867] serial8250 serial8250.0: Couldn't set LCR to 224
- [ 14.361141] serial8250 serial8250.0: Couldn't set LCR to 224
- [ 14.381184] serial8250.0: ttyS0 at MMIO 0x96400000 (irq = 59) is a 16550A
- [ 15.102015] console [ttyS0] enabled
- [ 15.139457] comcerto_otp_probe.
- [ 15.202596] loop: module loaded
- [ 15.217795] PCI: enabling device 0000:00:00.0 (0140 -> 0142)
- [ 15.223576] ahci: SSS flag set, parallel bus scan disabled
- [ 15.229165] ahci 0000:00:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
- [ 15.237301] ahci 0000:00:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs
- [ 15.264181] scsi0 : ahci
- [ 15.273336] scsi1 : ahci
- [ 15.276949] ata1: SATA max UDMA/133 abar m512@0xa0010000 port 0xa0010100 irq 96
- [ 15.284291] ata2: SATA max UDMA/133 abar m512@0xa0010000 port 0xa0010180 irq 96
- [ 15.296702] SATA Serdes: 48Mhz ref clk
- [ 15.300943] Serdes1: Lane OK Passed
- [ 15.304902] Serdes2: Lane OK Passed
- [ 15.308438] ahci ahci: forcing PORTS_IMPL to 0x3
- [ 15.313122] ahci ahci: AHCI 0001.0300 32 slots 2 ports 3 Gbps 0x3 impl platform mode
- [ 15.320911] ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
- [ 15.345131] scsi2 : ahci_platform
- [ 15.354619] scsi3 : ahci_platform
- [ 15.360170] ata3: SATA max UDMA/133 mmio [mem 0x9d000000-0x9d00ffff] port 0x100 irq 48
- [ 15.368160] ata4: SATA max UDMA/133 mmio [mem 0x9d000000-0x9d00ffff] port 0x180 irq 48
- [ 15.376802] designware_spi_probe:Initializing SPI Controller : Using dma=0 CLK(DUS)=250000000 Hz
- [ 15.387878] comcerto_spi comcerto_spi.1: at 0x96500000 mapped to 0xC080A000, irq=60
- [ 15.395601] designware_spi_probe:Initializing SPI Controller : Using dma=0 CLK(spi_i2c)=250000000 Hz
- [ 15.418110] comcerto_spi comcerto_spi.0: at 0x90498000 mapped to 0xC080C000, irq=61
- [ 15.445703] comcertoflash: probe of comcertoflash.0 failed with error -5
- [ 15.455876] m25p80 spi0.0: found mx25l8005, expected s25fl256s0
- [ 15.461875] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
- [ 15.466722] 3 cmdlinepart partitions found on MTD device spi0.0
- [ 15.472658] Creating 3 MTD partitions on "spi0.0":
- [ 15.477482] 0x000000000000-0x000000040000 : "uloader"
- [ 15.489056] 0x000000040000-0x0000000c0000 : "barebox"
- [ 15.505759] 0x0000000c0000-0x000000100000 : "env"
- [ 15.521844] pdev->resource->start = c8300000, pdev->resource->end = c8301fff
- [ 15.528970] nand_probe: comcertonand base: 0xc0800000
- [ 15.534137] ONFI flash detected
- [ 15.537387] ONFI param page 0 valid
- [ 15.540888] NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD S34ML02G1)
- [ 15.548069] hw_syndrome correction 2048.
- [ 15.552001] Using default values for hw ecc
- [ 15.559497] Bad block table not found for chip 0
- [ 15.567382] Bad block table not found for chip 0
- [ 15.572012] Scanning device for bad blocks
- [ 15.653821] Bad block table written to 0x00000ffe0000, version 0x01
- [ 15.661973] Bad block table written to 0x00000ffc0000, version 0x01
- [ 15.668319] 6 cmdlinepart partitions found on MTD device comcertonand
- [ 15.674778] Creating 6 MTD partitions on "comcertonand":
- [ 15.680124] 0x000000000000-0x000000a00000 : "config"
- [ 15.691577] 0x000000a00000-0x000001400000 : "kernel1"
- [ 15.708276] 0x000001400000-0x000008200000 : "rootfs1"
- [ 15.723444] 0x000008200000-0x000008c00000 : "kernel2"
- [ 15.735116] 0x000008c00000-0x00000fa00000 : "rootfs2"
- [ 15.752324] 0x00000fa00000-0x000010000000 : "reserved"
- [ 15.780604] Fixed MDIO Bus: probed
- [ 15.784663] ## xhci_plat_probe
- [ 15.787815] ### comcerto_start_xhci
- [ 15.791361] USB3.0 clock selected: internal
- [ 15.798818] xhci-hcd xhci-hcd: xHCI Host Controller
- [ 15.803826] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
- [ 15.811065] xhci-hcd xhci-hcd: irq 54, io mem 0x9f000000
- [ 15.816482] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- [ 15.823290] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 15.830564] usb usb1: Product: xHCI Host Controller
- [ 15.835455] usb usb1: Manufacturer: Linux 3.2.54 xhci-hcd
- [ 15.840883] usb usb1: SerialNumber: xhci-hcd
- [ 15.846371] hub 1-0:1.0: USB hub found
- [ 15.850156] hub 1-0:1.0: 1 port detected
- [ 15.862797] xhci-hcd xhci-hcd: xHCI Host Controller
- hotplug394add:[ 15.867794] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
- [ 15.876126] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
- hotplug395add:9[ 15.882967] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 15.891547] usb usb2: Product: xHCI Host Controller
- [ 15.896613] usb usb2: Manufacturer: Linux 3.2.54 xhci-hcd
- hotplug395add:[9[ 15.902031] usb usb2: SerialNumber: xhci-hcd
- /0/0]USB hub device:09h/xxh/xxh
- [ 15.913757] hub 2-0:1.0: USB hub found
- [ 15.917578] hub 2-0:1.0: 1 port detected
- [ 15.931239] usbcore: registered new interface driver usblp
- [ 15.936813] Initializing USB Mass Storage driver...
- [ 15.946136] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
- [ 15.956436] usbcore: registered new interface driver usb-storage
- [ 15.957510] ata4.00: ATA-9: WDC WD60EFRX-68L0BN1, 82.00A82, max UDMA/133
- [ 15.957518] ata4.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
- [ 15.976105] USB Mass Storage support registered.
- [ 15.977533] ata4.00: configured for UDMA/133
- [ 15.986403] dwc_otg: version 2.94a 27-OCT-2011
- hotplug397add:
- hotplug398add:[9/0/0]USB hub device:09h/xxh/xxh
- [ 16.166071] usb 1-1: new high-speed USB device number 2 using xhci-hcd
- [ 16.190887] Core Release: 2.81a
- [ 16.194039] Setting default values for core params
- [ 16.212019] usb 1-1: New USB device found, idVendor=174c, idProduct=2074
- [ 16.218757] usb 1-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
- [ 16.225912] usb 1-1: Product: ASM107x
- [ 16.229589] usb 1-1: Manufacturer: Asmedia
- [ 16.233696] usb 1-1: SerialNumber: 0000000A0003
- hotplug403add:[ 16.268818] hub 1-1:1.0: USB hub found
- [ 16.273038] hub 1-1:1.0: 4 ports detected
- hotplug404add:9
- hotplug404add:[9/0/1]USB hub device:09h/xxh/xxh
- [ 16.398819] Using Buffer DMA mode
- [ 16.402145] Periodic Transfer Interrupt Enhancement - disabled
- [ 16.407999] Multiprocessor Interrupt Enhancement - disabled
- [ 16.413587] OTG VER PARAM: 0, OTG VER FLAG: 0
- [ 16.417996] dwc_otg dwc_otg.0: DWC OTG Controller
- [ 16.422751] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 3
- [ 16.429849] dwc_otg dwc_otg.0: irq 53, io mem 0x00000000
- [ 16.435236] Init: Port Power? op_state=1
- [ 16.439181] Init: Power Port (0)
- [ 16.442480] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
- [ 16.449297] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 16.456545] usb usb3: Product: DWC OTG Controller
- [ 16.461261] usb usb3: Manufacturer: Linux 3.2.54 dwc_otg
- [ 16.466592] usb usb3: SerialNumber: dwc_otg.0
- [ 16.472222] hub 3-0:1.0: USB hub found
- [ 16.476007] hub 3-0:1.0: 1 port detected
- [ 16.494309] mousedev: PS/2 mouse device common for all mice
- hotplug406add:
- hotplug407add:9
- [ 16.521309] c2k-rtc c2k-rtc: rtc core: registered c2k as rtc0
- [ 16.527113] C2000 RTC, (c) 2012 Mindspeed Technologies
- [ 16.532387] c2k-rtc c2k-rtc: Warning: Invalid RTC value so initializing it
- hotplug407add:[9/0/0]USB hub dev[ 16.545395] i2c /dev entries driver
- [ 16.550640] comcerto_i2c_calculate_dividers: speed=97kHz, M=1, N=7, dividers=0x0f
- [ 16.565252] i2c-core: driver [eeprom] using legacy suspend method
- [ 16.571397] i2c-core: driver [eeprom] using legacy resume method
- [ 16.585820] comcerto_wdt: support registered
- [ 16.590355] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
- [ 16.596945] md: linear personality registered for level -1
- [ 16.602447] md: raid0 personality registered for level 0
- [ 16.607808] md: raid1 personality registered for level 1
- [ 16.613136] md: raid10 personality registered for level 10
- [ 16.618664] md: raid6 personality registered for level 6
- [ 16.623991] md: raid5 personality registered for level 5
- [ 16.628544] usb 2-1: New USB device found, idVendor=174c, idProduct=3074
- [ 16.628551] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
- [ 16.628557] usb 2-1: Product: ASM107x
- [ 16.628562] usb 2-1: Manufacturer: Asmedia
- [ 16.628567] usb 2-1: SerialNumber: 0000000A0003
- [ 16.644687] hub 2-1:1.0: USB hub found
- [ 16.644896] hub 2-1:1.0: 4 ports detected
- [ 16.663329] md: raid4 personality registered for level 4
- hotplug424add:9
- [ 16.674354] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
- hotplug424add:[9/0/0]USB hub device:09h/xxh/xxh
- [ 16.741408] usbcore: registered new interface driver usbhid
- [ 16.747051] usbhid: USB HID core driver
- [ 16.751641] etherip: Ethernet over IPv4 tunneling driver
- [ 16.756210] usb 1-1.3: new high-speed USB device number 3 using xhci-hcd
- [ 16.763717] etherip ----- is functional
- [ 16.773698] TCP cubic registered
- [ 16.777497] NET: Registered protocol family 10
- [ 16.779485] usb 1-1.3: New USB device found, idVendor=054c, idProduct=0243
- [ 16.779492] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- [ 16.779499] usb 1-1.3: Product: Storage Media
- [ 16.779504] usb 1-1.3: Manufacturer: Sony
- [ 16.779509] usb 1-1.3: SerialNumber: 1505112125225
- [ 16.780087] usb 1-1.3: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes
- [ 16.780101] usb 1-1.3: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframes
- [ 16.806040] scsi4 : usb-storage 1-1.3:1.0
- [ 16.834348] IPv6 over IPv4 tunneling driver
- hotplug446add:8
- hotplug445add:
- [ 16.865792] NET: Registered protocol family 17
- [ 16.870475] 8021q: 802.1Q VLAN Support v1.8
- [ 16.874694] Registering the dns_resolver key type
- [ 16.879463] Clocks: disabled unused uart
- [ 16.883396] Clocks: disabled unused gemtx
- [ 16.887438] Clocks: disabled unused ipsec_spacc
- [ 16.891980] Clocks: disabled unused dpi_cie
- [ 16.896196] Clocks: disabled unused dpi_decomp
- [ 16.900653] Clocks: disabled unused pcie1
- [ 16.904673] Clocks: disabled unused ext_phy0
- [ 16.908990] Clocks: disabled unused ext_phy1
- [ 16.913273] Clocks: disabled unused ext_phy2
- [ 16.917573] Clocks: disabled unused tpi
- [ 16.921418] Clocks: disabled unused csys
- [ 16.925350] Clocks: disabled unused tsuntg
- [ 16.929474] Clocks: disabled unused sata_occ
- [ 16.933755] Clocks: disabled unused pcie_occ
- [ 16.938051] Clocks: disabled unused sgmii_occ
- [ 16.954357] UBI: attaching mtd2 to ubi0
- [ 16.961556] UBI: scanning is finished
- [ 16.965232] UBI error: ubi_read_volume_table: the layout volume was not found
- [ 16.972428] UBI error: ubi_attach_mtd_dev: failed to attach mtd2, error -22
- [ 16.979440] UBI error: ubi_init: cannot attach mtd2
- [ 16.984425] c2k-rtc c2k-rtc: setting system clock to 2012-07-12 18:25:01 UTC (1342117501)
- [ 17.777212] scsi 4:0:0:0: Direct-Access Sony Storage Media 0100 PQ: 0 ANSI: 0 CCS
- [ 17.792335] sd 4:0:0:0: [sda] 2030592 512-byte logical blocks: (1.03 GB/991 MiB)
- [ 17.796677] sd 4:0:0:0: Attached scsi generic sg0 type 0
- [ 17.807595] sd 4:0:0:0: [sda] Write Protect is off
- [ 17.812985] sd 4:0:0:0: [sda] No Caching mode page found
- [ 17.818334] sd 4:0:0:0: [sda] Assuming drive cache: write through
- [ 17.827737] sd 4:0:0:0: [sda] No Caching mode page found
- [ 17.833071] sd 4:0:0:0: [sda] Assuming drive cache: write through
- [ 17.903438] sda: sda1
- [ 17.909028] sd 4:0:0:0: [sda] No Caching mode page found
- [ 17.914369] sd 4:0:0:0: [sda] Assuming drive cache: write through
- [ 17.914379] sd 4:0:0:0: [sda] Attached SCSI removable disk
- hotplug468add:[/block/sda][sda]Mass Storage device
- [ 19.196072] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
- [ 19.202842] ata3.00: ATA-9: WDC WD60EFRX-68L0BN1, 82.00A82, max UDMA/133
- [ 19.209575] ata3.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
- [ 19.217077] ata3.00: configured for UDMA/133
- [ 19.496075] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
- [ 19.502903] ata1.00: ATA-9: WDC WD60EFRX-68L0BN1, 82.00A82, max UDMA/133
- [ 19.509633] ata1.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
- [ 19.517555] ata1.00: configured for UDMA/133
- [ 19.522173] scsi 0:0:0:0: Direct-Access ATA WDC WD60EFRX-68L 82.0 PQ: 0 ANSI: 5
- [ 19.536517] sd 0:0:0:0: [sdb] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
- [ 19.544386] sd 0:0:0:0: [sdb] 4096-byte physical blocks
- [ 19.550148] sd 0:0:0:0: [sdb] Write Protect is off
- [ 19.555030] sd 0:0:0:0: Attached scsi generic sg1 type 0
- [ 19.560582] sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- [ 19.630445] sdb: sdb1 sdb2 sdb3
- [ 19.641437] sd 0:0:0:0: [sdb] Attached SCSI disk
- hotplug477add:[/block/sdb][sdb]Mass Storage device
- [ 20.116080] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
- [ 20.122934] ata2.00: ATA-9: WDC WD60EFRX-68L0BN1, 82.00A82, max UDMA/133
- [ 20.129668] ata2.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
- [ 20.138442] ata2.00: configured for UDMA/133
- [ 20.143069] scsi 1:0:0:0: Direct-Access ATA WDC WD60EFRX-68L 82.0 PQ: 0 ANSI: 5
- [ 20.154971] sd 1:0:0:0: [sdc] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
- [ 20.162866] sd 1:0:0:0: [sdc] 4096-byte physical blocks
- [ 20.166181] sd 1:0:0:0: Attached scsi generic sg2 type 0
- [ 20.174237] sd 1:0:0:0: [sdc] Write Protect is off
- [ 20.179276] scsi 2:0:0:0: Direct-Access ATA WDC WD60EFRX-68L 82.0 PQ: 0 ANSI: 5
- [ 20.186162] sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- [ 20.200241] sd 2:0:0:0: [sdd] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
- [ 20.208220] sd 2:0:0:0: [sdd] 4096-byte physical blocks
- [ 20.210096] sd 2:0:0:0: Attached scsi generic sg3 type 0
- [ 20.214648] scsi 3:0:0:0: Direct-Access ATA WDC WD60EFRX-68L 82.0 PQ: 0 ANSI: 5
- [ 20.227953] sd 3:0:0:0: [sde] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
- [ 20.229250] sd 2:0:0:0: [sdd] Write Protect is off
- [ 20.229327] sd 2:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- [ 20.249729] sd 3:0:0:0: [sde] 4096-byte physical blocks
- [ 20.255478] sd 3:0:0:0: [sde] Write Protect is off
- [ 20.261033] sd 3:0:0:0: Attached scsi generic sg4 type 0
- [ 20.266257] sd 3:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- [ 20.293172] sdc: sdc1 sdc2 sdc3
- [ 20.304118] sd 1:0:0:0: [sdc] Attached SCSI disk
- hotplug502add:[/block/sdc][sdc]M[ 20.317576] sdd: sdd1 sdd2 sdd3
- ass Storage devi[ 20.323462] sde: sde1 sde2 sde3
- ce
- hotplug506add:[/block/sdd][sdd]Mass Storage device
- hotplug507add:[/block/sde][sde]Mass Storage device
- [ 20.355183] sd 2:0:0:0: [sdd] Attached SCSI disk
- [ 20.360666] sd 3:0:0:0: [sde] Attached SCSI disk
- [ 20.371417] Freeing init memory: 3128K
- *** Stage 1: Setup system and device drivers ***
- Fail to open gpio device
- [ 22.359893] pfe_module_init
- [ 22.362755] pfe_platform_probe
- [ 22.367047] ipsec: baseaddr :9a000000 --- c0a00000
- [ 22.372861] pfe_probe
- [ 22.375139] PFE Driver version:
- [ 22.375142] pfe_ctrl_12_00_2
- [ 22.375144] built with pfe sources version: pfe_12_00_2
- [ 22.386438] cbus_baseaddr: c3000000, ddr_baseaddr: c2000000, ddr_phys_baseaddr: 3400000, ddr_size: c00000
- [ 22.396034] pfe_hw_init
- [ 22.398503] CLASS version: 20
- [ 22.401477] TMU version: 1011231
- [ 22.404712] BMU1 version: 21
- [ 22.407617] BMU2 version: 21
- [ 22.410505] EMAC1 network cfg: 80000
- [ 22.414088] EMAC2 network cfg: 80000
- [ 22.417689] EMAC3 network cfg: 80000
- [ 22.421272] EGPI1 version: 50
- [ 22.424246] EGPI2 version: 50
- [ 22.427237] EGPI3 version: 50
- [ 22.430210] HGPI version: 50
- [ 22.433095] GPT version: 0
- [ 22.435807] HIF version: 10
- [ 22.438618] HIF NOPCY version: 10
- [ 22.441940] UTIL version: 20
- [ 22.444828] bmu_init(1) done
- [ 22.447722] bmu_init(2) done
- [ 22.457228] class_init() done
- [ 22.460208] tmu_init: mem init
- [ 22.463269] tmu_init: lmem init
- [ 22.466465] tmu_init() done
- [ 22.469264] util_init() done
- [ 22.472154] gpi_init(1) done
- [ 22.475043] gpi_init(2) done
- [ 22.477939] gpi_init(3) done
- [ 22.480828] gpi_init(hif) done
- [ 22.483887] bmu_enable(1) done
- [ 22.486955] bmu_enable(2) done
- [ 22.490018] pfe_hif_lib_init
- [ 22.493105] pfe_hif_init
- [ 22.495644] pfe_hif_alloc_descr
- [ 22.499006] pfe_hif_init_buffers
- [ 22.502381] pfe_firmware_init
- [ 22.524413] pfe_load_elf
- [ 22.527006] pe_load_ddr_section: load address(3fb0000) and elf file address(c083b000) rcvd
- [ 22.557950] PFE binary version: pfe_12_00_2
- [ 22.562150] pfe_firmware_init: class firmware loaded 0xb20 0xc3010000
- [ 22.568614] pfe_load_elf
- [ 22.572502] pfe_firmware_init: tmu firmware loaded 0x220
- [ 22.577833] pfe_load_elf
- [ 22.582263] pfe_firmware_init: util firmware loaded 0x16c0
- [ 22.587803] pfe_ctrl_init
- [ 22.611177] pfe_ctrl_init finished
- [ 22.614591] pfe_eth_init
- [ 22.618150] pfe_ctrl_timer
- [ 22.630565] Comcerto MDIO Bus: probed
- [ 22.728000] eth0: pfe_eth_init_one: created interface, baseaddr: c3200000
- [ 22.828092] eth1: pfe_eth_init_one: created interface, baseaddr: c3220000
- [ 22.834904] pfe_vwd_init
- [ 22.837651] pfe_vwd_init: created vwd device(250, 0)
- [ 22.842631] pfe_vwd_driver_init: start
- [ 22.846426] pfe_vwd_up: start
- [ 22.849447] comcerto_wifi_rx_fastpath_register:33 VWD Tx function registered
- [ 22.856543] pfe_vwd_driver_init: end
- [ 22.860129] pfe_pcap_init
- crw-rw---- 1 root root 10, 130 Jul 12 18:25 /dev/comcerto_wdt
- Starting watchdog ...
- -rw-r--r-- 1 root root 0 Jul [ 22.892391] MCU watchdog is reset!
- 12 18:25 /proc/mcu_wdt
- [ 23.382103] egiga0: pfe_eth_open
- [ 23.385567] hif_process_client_req: register client_id 0
- [ 23.390915] pfe_hif_client_register
- [ 23.394418] hif_lib_set_rx_cpu_affinity:Client (0) and HIF Rx processing will use same cpu
- [ 23.402723] egiga0: pfe_gemac_init
- [ 23.410900] egiga1: pfe_eth_open
- [ 23.414361] hif_process_client_req: register client_id 1
- [ 23.419707] pfe_hif_client_register
- [ 23.423213] hif_lib_set_rx_cpu_affinity:Client (1) and HIF Rx processing will use same cpu
- [ 23.431576] egiga1: pfe_gemac_init
- cat: can't open '/proc/hdd5_detect': No such file or directory
- *** Stage 2: Prepare the root file system ***
- mknod: /dev/gpio: File exists
- Initialize fan control
- Wrote to 0x90470058: 0x05000000
- Wrote to 0x90458000: 0x80000001
- Wrote to 0x90458028: 0x80001388
- Mount system partition...
- crw-rw---- 1 root root 10, 58 Jul 12 2012 /dev/ubi_ctrl
- sda
- sdb
- sdc
- sdd
- sde
- checking sda
- Trying to mount /dev/sda1
- [ 24.274135] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
- md5 check ok
- + ECHO=/bin/echo
- + FLASH_ERASEALL=/sbin/flash_eraseall
- + ENV_PARTITION=/dev/mtd2
- + USB_PATH=/mnt/partnerkey
- + USB_FW_PATH=/mnt/partnerkey/nas5xx_fw
- + BUFFER_PATH=/mnt/partnerkey/buffer
- + FW_PATH=/firmware
- + exec
- [ 28.406269] PHY: comcerto-0:04 - Link is Up - 1000/Full
- [ 28.411540] pfe_eth_adjust_link: PHY: comcerto-0:04, phy->link: 1
- Doing pre-install ...
- ... pre-install finishes!
- [ 68.891644] UBI: attaching mtd5 to ubi5
- [ 69.619811] UBI: scanning is finished
- [ 69.636848] UBI: attached mtd5 (name "rootfs1", size 110 MiB) to ubi5
- [ 69.643315] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- [ 69.650141] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- [ 69.656900] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
- [ 69.663797] UBI: good PEBs: 880, bad PEBs: 0, corrupted PEBs: 0
- [ 69.669755] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
- [ 69.676921] UBI: max/mean erase counter: 6/4, WL threshold: 4096, image sequence number: 330185502
- [ 69.685905] UBI: available PEBs: 10, total reserved PEBs: 870, PEBs reserved for bad PEB handling: 40
- [ 69.695192] UBI: background thread "ubi_bgt5d" started, PID 1065
- [ 69.720586] UBI error: ubi_create_volume: volume "ubi_rootfs1" exists (ID 0)
- [ 69.727704] UBI error: ubi_create_volume: cannot create volume 1, error -17
- [ 69.853885] UBIFS: mounted UBI device 5, volume 0, name "ubi_rootfs1"
- [ 69.860365] UBIFS: file system size: 103612416 bytes (101184 KiB, 98 MiB, 816 LEBs)
- [ 69.868229] UBIFS: journal size: 5206016 bytes (5084 KiB, 4 MiB, 41 LEBs)
- [ 69.875559] UBIFS: media format: w4/r0 (latest is w4/r0)
- [ 69.881414] UBIFS: default compressor: lzo
- [ 69.885521] UBIFS: reserved for root: 4893869 bytes (4779 KiB)
- [ 96.294387] UBIFS: un-mount UBI device 5, volume 0
- [ 96.420094] UBI: attaching mtd7 to ubi7
- [ 97.147973] UBI: scanning is finished
- [ 97.163978] UBI: attached mtd7 (name "rootfs2", size 110 MiB) to ubi7
- [ 97.170469] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- [ 97.177294] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- [ 97.184016] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
- [ 97.190922] UBI: good PEBs: 880, bad PEBs: 0, corrupted PEBs: 0
- [ 97.196862] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
- [ 97.204017] UBI: max/mean erase counter: 6/4, WL threshold: 4096, image sequence number: 1035530652
- [ 97.213092] UBI: available PEBs: 10, total reserved PEBs: 870, PEBs reserved for bad PEB handling: 40
- [ 97.222352] UBI: background thread "ubi_bgt7d" started, PID 1086
- [ 97.251407] UBI error: ubi_create_volume: volume "ubi_rootfs2" exists (ID 0)
- [ 97.258527] UBI error: ubi_create_volume: cannot create volume 1, error -17
- [ 97.385383] UBIFS: mounted UBI device 7, volume 0, name "ubi_rootfs2"
- [ 97.391862] UBIFS: file system size: 103612416 bytes (101184 KiB, 98 MiB, 816 LEBs)
- [ 97.399722] UBIFS: journal size: 5206016 bytes (5084 KiB, 4 MiB, 41 LEBs)
- [ 97.407062] UBIFS: media format: w4/r0 (latest is w4/r0)
- [ 97.412911] UBIFS: default compressor: lzo
- [ 97.417030] UBIFS: reserved for root: 4893869 bytes (4779 KiB)
- [ 123.839818] UBIFS: un-mount UBI device 7, volume 0
- Doing post-install ...
- ... post-install finishes!
- [ 160.555727] sd 3:0:0:0: [sde] Synchronizing SCSI cache
- [ 161.057986] sd 3:0:0:0: [sde] Stopping disk
- [ 161.062199]
- [ 161.062201] ****** disk(3:0:0:0) spin down at 4294953402 ******
- [ 163.838523] sd 2:0:0:0: [sdd] Synchronizing SCSI cache
- [ 163.843797] sd 2:0:0:0: [sdd] Stopping disk
- [ 163.848020]
- [ 163.848021] ****** disk(2:0:0:0) spin down at 4294953681 ******
- [ 164.415642] sd 1:0:0:0: [sdc] Synchronizing SCSI cache
- [ 164.420931] sd 1:0:0:0: [sdc] Stopping disk
- [ 164.425135]
- [ 164.425137] ****** disk(1:0:0:0) spin down at 4294953738 ******
- [ 164.992905] sd 0:0:0:0: [sdb] Synchronizing SCSI cache
- [ 164.998184] sd 0:0:0:0: [sdb] Stopping disk
- [ 165.002386]
- [ 165.002388] ****** disk(0:0:0:0) spin down at 4294953796 ******
- [ 165.570261] Power down.
- [ 165.572720] GPIO[15] is pull high for power off
- [ 169.347677] ata3: exception Emask 0x10 SAct 0x0 SErr 0x10200 action 0xe frozen
Add Comment
Please, Sign In to add comment