SHARE
TWEET

h3ulcb-kf-boot

a guest Mar 27th, 2020 153 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. [    0.000149] NOTICE:  BL2: R-Car H3/M3/M3N Initial Program Loader(CA57)
  2. [    0.005190] NOTICE:  BL2: Initial Program Loader(Rev.2.0.3)
  3. [    0.010723] NOTICE:  BL2: PRR is R-Car H3 Ver.2.0
  4. [    0.015391] NOTICE:  BL2: Board is Starter Kit Rev.1.0
  5. [    0.020505] NOTICE:  BL2: Boot device is HyperFlash(80MHz)
  6. [    0.025930] NOTICE:  BL2: LCM state is CM
  7. [    0.029972] NOTICE:  BL2: AVS setting succeeded. DVFS_SetVID=0x53
  8. [    0.035947] NOTICE:  BL2: CH0: 0x400000000 - 0x43fffffff, 1 GiB
  9. [    0.041809] NOTICE:  BL2: CH1: 0x500000000 - 0x53fffffff, 1 GiB
  10. [    0.047684] NOTICE:  BL2: CH2: 0x600000000 - 0x63fffffff, 1 GiB
  11. [    0.053559] NOTICE:  BL2: CH3: 0x700000000 - 0x73fffffff, 1 GiB
  12. [    0.059448] NOTICE:  BL2: DDR3200(rev.0.35)
  13. [    0.075214] NOTICE:  BL2: [COLD_BOOT]
  14. [    0.084189] NOTICE:  BL2: DRAM Split is 4ch
  15. [    0.086882] NOTICE:  BL2: QoS is default setting(rev.0.21)
  16. [    0.092325] NOTICE:  BL2: DRAM refresh interval 1.95 usec
  17. [    0.097682] NOTICE:  BL2: Periodic Write DQ Training
  18. [    0.111700] NOTICE:  BL2: Lossy Decomp areas
  19. [    0.114480] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
  20. [    0.121565] NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
  21. [    0.128477] NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
  22. [    0.210051] ERROR:   Image magic is wrong!
  23. [    0.212659] ERROR:   Bootloader partition 2 corrupted, setting unbootable
  24. [    0.219807] NOTICE:  BL2: v1.5(release):5ceebc7
  25. [    0.223891] NOTICE:  BL2: Built : 15:36:03, Aug 28 2019
  26. [    0.229078] NOTICE:  BL2: Normal boot
  27. [    0.232714] NOTICE:  BL2: eMMC boot from partition 1
  28. [    0.237631] NOTICE:  BL2: Load dst=0xe632b100 src=(p:1)0x30000(384) len=0x200(1)
  29. [    0.245328] NOTICE:  BL2: Load dst=0x43f00000 src=(p:1)0x30400(386) len=0x1800(12)
  30. [    0.252861] NOTICE:  BL2: Load dst=0x44000000 src=(p:1)0x40000(512) len=0x10000(128)
  31. [    0.261900] NOTICE:  BL2: Load dst=0x44100000 src=(p:1)0x80000(1024) len=0x100000(2048)
  32. [    0.291294] NOTICE:  BL2: Load dst=0x50000000 src=(p:1)0x200000(4096) len=0x200000(4096)
  33. [    0.343429] NOTICE:  BL2: Booting BL31
  34.  
  35.  
  36. U-Boot 2018.09-00075-gbf1a1d5 (Aug 28 2019 - 15:36:04 +0200)
  37.  
  38. Config: r8a7795-h3ulcb-u-boot
  39. CPU: Renesas Electronics R8A7795 rev 2.0
  40. Model: Renesas H3ULCB board based on r8a7795 ES2.0+
  41. DRAM:  3.9 GiB
  42. Bank #0: 0x048000000 - 0x07fffffff, 896 MiB
  43. Bank #1: 0x500000000 - 0x53fffffff, 1 GiB
  44. Bank #2: 0x600000000 - 0x63fffffff, 1 GiB
  45. Bank #3: 0x700000000 - 0x73fffffff, 1 GiB
  46.  
  47. MMC:   sd@ee100000: 0, sd@ee140000: 1
  48. Loading Environment from MMC... OK
  49. In:    serial@e6e88000
  50. Out:   serial@e6e88000
  51. Err:   serial@e6e88000
  52. Net:   eth0: ethernet@e6800000
  53. Setting bootmode 'android'
  54. Hit any key to stop autoboot:  0
  55. starting USB...
  56. USB0:   USB EHCI 1.10
  57. scanning bus 0 for devices... 4 USB Device(s) found
  58.        scanning usb for storage devices... 1 Storage Device(s) found
  59. 16497152 bytes read in 419 ms (37.5 MiB/s)
  60. USB stick found
  61. 16497152 bytes read in 396 ms (39.7 MiB/s)
  62. 92809 bytes read in 35 ms (2.5 MiB/s)
  63. stopping USB..
  64. ## Flattened Device Tree blob at 48000000
  65.    Booting using the fdt blob at 0x48000000
  66.    Using Device Tree in place at 0000000048000000, end 0000000048019a88
  67.  
  68. Starting kernel ...
  69.  
  70. [    0.000000] Booting Linux on physical CPU 0x0
  71. [    0.000000] Linux version 4.14.75-ltsi-yocto-standard (oe-user@oe-host) (gcc version 7.3.0 (GCC)) #1 SMP PREEMPT Wed Mar 25 09:40:19 UTC 2020
  72. [    0.000000] Boot CPU: AArch64 Processor [411fd073]
  73. [    0.000000] Machine model: Renesas H3ULCB Kingfisher board based on r8a7795 ES2.0+
  74. [    0.000000] efi: Getting EFI parameters from FDT:
  75. [    0.000000] efi: UEFI not found.
  76. [    0.000000] Reserved memory: created CMA memory pool at 0x0000000057000000, size 400 MiB
  77. [    0.000000] OF: reserved mem: initialized node linux,cma@57000000, compatible id shared-dma-pool
  78. [    0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB
  79. [    0.000000] OF: reserved mem: initialized node linux,multimedia@70000000, compatible id shared-dma-pool
  80. [    0.000000] NUMA: No NUMA configuration found
  81. [    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000073fffffff]
  82. [    0.000000] NUMA: NODE_DATA [mem 0x73ff6b000-0x73ff6caff]
  83. [    0.000000] Zone ranges:
  84. [    0.000000]   DMA      [mem 0x0000000048000000-0x00000000ffffffff]
  85. [    0.000000]   Normal   [mem 0x0000000100000000-0x000000073fffffff]
  86. [    0.000000] Movable zone start for each node
  87. [    0.000000] Early memory node ranges
  88. [    0.000000]   node   0: [mem 0x0000000048000000-0x0000000053ffffff]
  89. [    0.000000]   node   0: [mem 0x0000000057000000-0x000000007fffffff]
  90. [    0.000000]   node   0: [mem 0x0000000500000000-0x000000053fffffff]
  91. [    0.000000]   node   0: [mem 0x0000000600000000-0x000000063fffffff]
  92. [    0.000000]   node   0: [mem 0x0000000700000000-0x000000073fffffff]
  93. [    0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000073fffffff]
  94. [    0.000000] psci: probing for conduit method from DT.
  95. [    0.000000] psci: PSCIv1.1 detected in firmware.
  96. [    0.000000] psci: Using standard PSCI v0.2 function IDs
  97. [    0.000000] psci: Trusted OS resident on physical CPU 0x0
  98. [    0.000000] psci: SMC Calling Convention v1.1
  99. [    0.000000] percpu: Embedded 24 pages/cpu @ffff8006ffea6000 s57624 r8192 d32488 u98304
  100. [    0.000000] Detected PIPT I-cache on CPU0
  101. [    0.000000] Speculative Store Bypass Disable mitigation not required
  102. [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 987840
  103. [    0.000000] Policy zone: Normal
  104. [    0.000000] Kernel command line: androidboot.boottime=6.684 rw root=/dev/sda1 rootfstype=ext4 rootwait
  105. [    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
  106. [    0.000000] software IO TLB [mem 0x4ffff000-0x53fff000] (64MB) mapped at [ffff80000ffff000-ffff800013ffefff]
  107. [    0.000000] Memory: 3192796K/4014080K available (10364K kernel code, 686K rwdata, 4272K rodata, 768K init, 404K bss, 149540K reserved, 671744K cma-reserved)
  108. [    0.000000] Virtual kernel memory layout:
  109. [    0.000000]     modules : 0xffff000000000000 - 0xffff000008000000   (   128 MB)
  110. [    0.000000]     vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000   (129022 GB)
  111. [    0.000000]       .text : 0xffff000008080000 - 0xffff000008aa0000   ( 10368 KB)
  112. [    0.000000]     .rodata : 0xffff000008aa0000 - 0xffff000008ed0000   (  4288 KB)
  113. [    0.000000]       .init : 0xffff000008ed0000 - 0xffff000008f90000   (   768 KB)
  114. [    0.000000]       .data : 0xffff000008f90000 - 0xffff00000903ba00   (   687 KB)
  115. [    0.000000]        .bss : 0xffff00000903ba00 - 0xffff0000090a0c10   (   405 KB)
  116. [    0.000000]     fixed   : 0xffff7dfffe7f9000 - 0xffff7dfffec00000   (  4124 KB)
  117. [    0.000000]     PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000   (    16 MB)
  118. [    0.000000]     vmemmap : 0xffff7e0000000000 - 0xffff800000000000   (  2048 GB maximum)
  119. [    0.000000]               0xffff7e0000200000 - 0xffff7e001c000000   (   446 MB actual)
  120. [    0.000000]     memory  : 0xffff800008000000 - 0xffff800700000000   ( 28544 MB)
  121. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
  122. [    0.000000] Preemptible hierarchical RCU implementation.
  123. [    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8.
  124. [    0.000000]  Tasks RCU enabled.
  125. [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
  126. [    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
  127. [    0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (virt).
  128. [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns
  129. [    0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns
  130. [    0.000115] Console: colour dummy device 80x25
  131. [    0.000342] console [tty0] enabled
  132. [    0.000388] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333)
  133. [    0.000400] pid_max: default: 32768 minimum: 301
  134. [    0.000453] Security Framework initialized
  135. [    0.002065] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
  136. [    0.002896] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
  137. [    0.002942] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
  138. [    0.002975] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
  139. [    0.015931] ASID allocator initialised with 32768 entries
  140. [    0.023921] Hierarchical SRCU implementation.
  141. [    0.032751] Detected Renesas R-Car Gen3 r8a7795 ES2.0
  142. [    0.033533] EFI services will not be available.
  143. [    0.039948] smp: Bringing up secondary CPUs ...
  144. [    0.068130] Detected PIPT I-cache on CPU1
  145. [    0.068169] CPU1: Booted secondary processor [411fd073]
  146. [    0.096147] Detected PIPT I-cache on CPU2
  147. [    0.096168] CPU2: Booted secondary processor [411fd073]
  148. [    0.124174] Detected PIPT I-cache on CPU3
  149. [    0.124193] CPU3: Booted secondary processor [411fd073]
  150. [    0.152220] CPU features: enabling workaround for ARM erratum 845719
  151. [    0.152228] Detected VIPT I-cache on CPU4
  152. [    0.152266] CPU4: Booted secondary processor [410fd034]
  153. [    0.180242] Detected VIPT I-cache on CPU5
  154. [    0.180264] CPU5: Booted secondary processor [410fd034]
  155. [    0.208274] Detected VIPT I-cache on CPU6
  156. [    0.208296] CPU6: Booted secondary processor [410fd034]
  157. [    0.236310] Detected VIPT I-cache on CPU7
  158. [    0.236332] CPU7: Booted secondary processor [410fd034]
  159. [    0.236403] smp: Brought up 1 node, 8 CPUs
  160. [    0.236461] SMP: Total of 8 processors activated.
  161. [    0.236468] CPU features: detected feature: 32-bit EL0 Support
  162. [    0.236474] CPU features: detected feature: Kernel page table isolation (KPTI)
  163. [    0.242665] CPU: All CPU(s) started at EL1
  164. [    0.242690] alternatives: patching kernel code
  165. [    0.243417] devtmpfs: initialized
  166. [    0.249831] random: get_random_u32 called from bucket_table_alloc+0x108/0x260 with crng_init=0
  167. [    0.250240] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
  168. [    0.250303] futex hash table entries: 2048 (order: 6, 262144 bytes)
  169. [    0.258357] pinctrl core: initialized pinctrl subsystem
  170. [    0.259513] DMI not present or invalid.
  171. [    0.259721] NET: Registered protocol family 16
  172. [    0.260853] cpuidle: using governor menu
  173. [    0.260973] vdso: 2 pages (1 code @ ffff000008aa6000, 1 data @ ffff000008f95000)
  174. [    0.260990] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  175. [    0.261646] DMA: preallocated 256 KiB pool for atomic allocations
  176. [    0.261722] Serial: AMBA PL011 UART driver
  177. [    0.265190] sh-pfc e6060000.pin-controller: r8a77951_pfc support registered
  178. [    0.289219] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
  179. [    0.290258] ACPI: Interpreter disabled.
  180. [    0.292555] rcar-avs: use avs value: 0
  181. [    0.292692] rcar-avs: /cpus/cpu@0 is running with: /opp_table0
  182. [    0.292704] rcar-avs: /cpus/cpu@1 is running with: /opp_table0
  183. [    0.292716] rcar-avs: /cpus/cpu@2 is running with: /opp_table0
  184. [    0.292728] rcar-avs: /cpus/cpu@3 is running with: /opp_table0
  185. [    0.292755] rcar-avs: /soc/gsx@fd000000 is running with: /gsx_opp_table0
  186. [    0.294503] ipmmu-vmsa e67b0000.mmu: IPMMU context 0 is reserved
  187. [    0.294988] vgaarb: loaded
  188. [    0.295158] SCSI subsystem initialized
  189. [    0.295434] usbcore: registered new interface driver usbfs
  190. [    0.295465] usbcore: registered new interface driver hub
  191. [    0.295532] usbcore: registered new device driver usb
  192. [    0.296323] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 400000 Hz
  193. [    0.296628] media: Linux media interface: v0.10
  194. [    0.296655] Linux video capture interface: v2.00
  195. [    0.296714] pps_core: LinuxPPS API ver. 1 registered
  196. [    0.296722] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  197. [    0.296740] PTP clock support registered
  198. [    0.297033] EDAC MC: Ver: 3.0.0
  199. [    0.297210] dmi: Firmware registration failed.
  200. [    0.297724] Advanced Linux Sound Architecture Driver Initialized.
  201. [    0.298207] clocksource: Switched to clocksource arch_sys_counter
  202. [    0.298312] VFS: Disk quotas dquot_6.6.0
  203. [    0.298349] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
  204. [    0.298450] pnp: PnP ACPI: disabled
  205. [    0.302085] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
  206. [    0.302192] NET: Registered protocol family 2
  207. [    0.302670] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
  208. [    0.302879] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
  209. [    0.303176] TCP: Hash tables configured (established 32768 bind 32768)
  210. [    0.303297] UDP hash table entries: 2048 (order: 4, 65536 bytes)
  211. [    0.303364] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
  212. [    0.303516] NET: Registered protocol family 1
  213. [    0.303747] RPC: Registered named UNIX socket transport module.
  214. [    0.303757] RPC: Registered udp transport module.
  215. [    0.303762] RPC: Registered tcp transport module.
  216. [    0.303768] RPC: Registered tcp NFSv4.1 backchannel transport module.
  217. [    0.304928] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
  218. [    0.305473] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available
  219. [    0.305910] kvm [1]: HYP mode not available
  220. [    0.307827] audit: initializing netlink subsys (disabled)
  221. [    0.307913] audit: type=2000 audit(0.303:1): state=initialized audit_enabled=0 res=1
  222. [    0.308171] workingset: timestamp_bits=44 max_order=20 bucket_order=0
  223. [    0.312213] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  224. [    0.312603] NFS: Registering the id_resolver key type
  225. [    0.312627] Key type id_resolver registered
  226. [    0.312634] Key type id_legacy registered
  227. [    0.312644] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  228. [    0.312762] 9p: Installing v9fs 9p2000 file system support
  229. [    0.314155] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
  230. [    0.314172] io scheduler noop registered
  231. [    0.314178] io scheduler deadline registered
  232. [    0.314255] io scheduler cfq registered (default)
  233. [    0.314263] io scheduler mq-deadline registered
  234. [    0.314269] io scheduler kyber registered
  235. [    0.317936] gpio_rcar e6050000.gpio: driving 16 GPIOs
  236. [    0.318173] gpio_rcar e6051000.gpio: driving 29 GPIOs
  237. [    0.318327] GPIO line 455 (BL PWM 100%) hogged as output/high
  238. [    0.318737] gpio_rcar e6052000.gpio: driving 15 GPIOs
  239. [    0.318958] gpio_rcar e6053000.gpio: driving 16 GPIOs
  240. [    0.319071] GPIO line 432 (MOST RST) hogged as output/high
  241. [    0.319184] gpio_rcar e6054000.gpio: driving 18 GPIOs
  242. [    0.319387] gpio_rcar e6055000.gpio: driving 26 GPIOs
  243. [    0.319500] GPIO line 381 (Onboard MCh Audio) hogged as output/high
  244. [    0.319601] gpio_rcar e6055400.gpio: driving 32 GPIOs
  245. [    0.319796] gpio_rcar e6055800.gpio: driving 4 GPIOs
  246. [    0.320764] rcar-pcie fe000000.pcie: no pcie3v3 regulator found
  247. [    0.320777] rcar-pcie fe000000.pcie: no pcie1v8 regulator found
  248. [    0.320787] OF: PCI: host bridge /soc/pcie@fe000000 ranges:
  249. [    0.320806] OF: PCI:    IO 0xfe100000..0xfe1fffff -> 0x00000000
  250. [    0.320819] OF: PCI:   MEM 0xfe200000..0xfe3fffff -> 0xfe200000
  251. [    0.320829] OF: PCI:   MEM 0x30000000..0x37ffffff -> 0x30000000
  252. [    0.320837] OF: PCI:   MEM 0x38000000..0x3fffffff -> 0x38000000
  253. [    0.386036] rcar-pcie fe000000.pcie: PCIe link down
  254. [    0.387491] EINJ: ACPI disabled.
  255. [    0.403306] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
  256. [    0.404569] SuperH (H)SCI(F) driver initialized
  257. [    0.405103] e6540000.serial: ttySC1 at MMIO 0xe6540000 (irq = 35, base_baud = 0) is a hscif
  258. [    0.405757] e6550000.serial: ttySC3 at MMIO 0xe6550000 (irq = 36, base_baud = 0) is a hscif
  259. [    0.406314] e6e68000.serial: ttySC2 at MMIO 0xe6e68000 (irq = 122, base_baud = 0) is a scif
  260. [    0.406800] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 123, base_baud = 0) is a scif
  261. [    1.519126] console [ttySC0] enabled
  262. [    1.524578] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
  263. [    1.531215] [drm] No driver support for vblank timestamp query.
  264. [    1.537770] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY)
  265. [    1.547733] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver
  266. [    1.561464] loop: module loaded
  267. [    1.567997] renesas-rpc ee200000.rpc0: using DMA read (dma0chan0)
  268. [    1.574523] Bad mode in Error handler detected on CPU1, code 0xbf000000 -- SError
  269. [    1.582007] Internal error: Oops - bad mode: 0 [#1] PREEMPT SMP
  270. [    1.587922] Modules linked in:
  271. [    1.590978] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.14.75-ltsi-yocto-standard #1
  272. [    1.598717] Hardware name: Renesas H3ULCB Kingfisher board based on r8a7795 ES2.0+ (DT)
  273. [    1.606717] task: ffff8006fb280000 task.stack: ffff000008078000
  274. [    1.612642] PC is at rpc_wait+0x28/0x88
  275. [    1.616474] LR is at rpc_wait+0x18/0x88
  276. [    1.620305] pc : [<ffff000008659188>] lr : [<ffff000008659178>] pstate: 20000045
  277. [    1.627695] sp : ffff00000807bbd0
  278. [    1.631005] x29: ffff00000807bbd0 x28: ffff000008f71128
  279. [    1.636315] x27: 0000000000000007 x26: ffff000008ed046c
  280. [    1.641624] x25: ffff000009040000 x24: 0000000000000000
  281. [    1.646933] x23: ffff8006faa5a800 x22: 0000000000000000
  282. [    1.652242] x21: ffff8006f9d0ac10 x20: ffff8006fa353f98
  283. [    1.657550] x19: ffff8006fa353f98 x18: 0000000000000000
  284. [    1.662859] x17: 0000000000000020 x16: ffff000008af2b80
  285. [    1.668168] x15: 0000000000000000 x14: 0000000000000400
  286. [    1.673476] x13: 0000000000000400 x12: 0000000000000030
  287. [    1.678784] x11: 0000000000000006 x10: 0101010101010101
  288. [    1.684093] x9 : ffffffffffffffff x8 : 7f7f7f7f7f7f7f7f
  289. [    1.689402] x7 : fefefeff646c606d x6 : 02000f00ec808080
  290. [    1.694710] x5 : 0000000000000000 x4 : ffff000009086f98
  291. [    1.700019] x3 : 0000000000000000 x2 : ffff000008f97000
  292. [    1.705327] x1 : 0000000000000000 x0 : 00000000fffee174
  293. [    1.710636] Process swapper/0 (pid: 1, stack limit = 0xffff000008078000)
  294. [    1.717333] Call trace:
  295. [    1.719775] Exception stack(0xffff00000807ba90 to 0xffff00000807bbd0)
  296. [    1.726211] ba80:                                   00000000fffee174 0000000000000000
  297. [    1.734037] baa0: ffff000008f97000 0000000000000000 ffff000009086f98 0000000000000000
  298. [    1.741863] bac0: 02000f00ec808080 fefefeff646c606d 7f7f7f7f7f7f7f7f ffffffffffffffff
  299. [    1.749688] bae0: 0101010101010101 0000000000000006 0000000000000030 0000000000000400
  300. [    1.757515] bb00: 0000000000000400 0000000000000000 ffff000008af2b80 0000000000000020
  301. [    1.765340] bb20: 0000000000000000 ffff8006fa353f98 ffff8006fa353f98 ffff8006f9d0ac10
  302. [    1.773165] bb40: 0000000000000000 ffff8006faa5a800 0000000000000000 ffff000009040000
  303. [    1.780991] bb60: ffff000008ed046c 0000000000000007 ffff000008f71128 ffff00000807bbd0
  304. [    1.788817] bb80: ffff000008659178 ffff00000807bbd0 ffff000008659188 0000000020000045
  305. [    1.796643] bba0: 0000000000000007 ffff0000084bec30 ffffffffffffffff ffff0000084bec4c
  306. [    1.804467] bbc0: ffff00000807bbd0 ffff000008659188
  307. [    1.809342] [<ffff000008659188>] rpc_wait+0x28/0x88
  308. [    1.814217] [<ffff000008659d68>] rpc_hf_mode_ext+0x18/0xe8
  309. [    1.819698] [<ffff00000865a5e4>] rpc_hf_probe+0xcc/0x340
  310. [    1.825009] [<ffff0000085ab8b8>] platform_drv_probe+0x58/0xb8
  311. [    1.830752] [<ffff0000085a9b20>] driver_probe_device+0x210/0x2d0
  312. [    1.836754] [<ffff0000085a9c9c>] __driver_attach+0xbc/0xc0
  313. [    1.842236] [<ffff0000085a7c7c>] bus_for_each_dev+0x4c/0x98
  314. [    1.847804] [<ffff0000085a9438>] driver_attach+0x20/0x28
  315. [    1.853111] [<ffff0000085a8f88>] bus_add_driver+0x1b8/0x228
  316. [    1.858678] [<ffff0000085aa638>] driver_register+0x60/0xf8
  317. [    1.864159] [<ffff0000085ab808>] __platform_driver_register+0x40/0x48
  318. [    1.870599] [<ffff000008f0668c>] rpc_hf_platform_driver_init+0x18/0x20
  319. [    1.877125] [<ffff000008083c90>] do_one_initcall+0x38/0x128
  320. [    1.882695] [<ffff000008ed0d0c>] kernel_init_freeable+0x188/0x22c
  321. [    1.888788] [<ffff000008a819d0>] kernel_init+0x10/0x108
  322. [    1.894009] [<ffff000008084ed8>] ret_from_fork+0x10/0x18
  323. [    1.899318] Code: d00049e2 f9454041 8b000020 14000005 (f9454041)
  324. [    1.905419] ---[ end trace 6127e019361de071 ]---
  325. [    1.910062] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
  326. [    1.910062]
  327. [    1.919196] SMP: stopping secondary CPUs
  328. [    1.923117] Kernel Offset: disabled
  329. [    1.926602] CPU features: 0x1802004
  330. [    1.930086] Memory Limit: none
  331. [    1.933139] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
  332. [    1.933139]
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
Top