[2018-09-05 08:54:07] [Output] : ★ Jared Lyall enters the vehicle, then clicks two buttons, opening the hood and the trunk.
[2018-09-05 08:54:14] [Output] : ★ Jared Lyall exits the vehicle.
[2018-09-05 08:54:17] [Output] : ★ Jared Lyall walks towards the back-end of the vehicle.
[2018-09-05 08:54:24] [Output] : ★ Jared Lyall raises the trunk until it's totally open
[2018-09-05 08:54:27] [Output] : Jared Lyall: (( .* ))
[2018-09-05 08:54:43] [Output] : ★ Jared Lyall reaches for the onboard toolkit and removes it. He places it onto the shelf.
[2018-09-05 08:55:02] [Output] : ★ Jared Lyall lifts the back wiper arm complete and pulls off the wiper blade.
[2018-09-05 08:55:08] [Output] : ★ Jared Lyall places the wiper blade onto the shelf.
[2018-09-05 08:55:20] [Output] : ★ Jared Lyall walks to the front-end of the car.
[2018-09-05 08:55:23] [Output] : ★ Jared Lyall folds the wiper arm.
[2018-09-05 08:55:31] [Output] : ★ Jared Lyall swings the wiper blade upwards.
[2018-09-05 08:55:34] [Output] : ★ Jared Lyall removes the wiper blade.
[2018-09-05 08:56:01] [Output] : ★ Jared Lyall raises the hood entirely and keeps it open after placing the wiper blade onto the shelf.
[2018-09-05 08:56:08] [Output] : ★ Jared Lyall places the support into position so that the hood stays open.
[2018-09-05 08:56:42] [Output] : ★ Jared Lyall turns the bulb cover from the inside and rotates it counter-clockwise.
[2018-09-05 08:56:55] [Output] : ★ Jared Lyall turns the bulb to the left, pulls off the connector and places it onto the shelf.
[2018-09-05 08:57:22] [Output] : ★ Jared Lyall unscrews the bulb holder with the bulb to the left.
[2018-09-05 08:58:39] [Output] : ★ Jared Lyall places the bulbs onto the shelf.
[2018-09-05 08:59:20] [Output] : ★ Jared Lyall untightens the nut on the battery's positive cable.
[2018-09-05 08:59:28] [Output] : ★ Jared Lyall starts unscrewing the bolt on the battery's positive cable.
[2018-09-05 08:59:34] [Output] : ★ Jared Lyall places the screw and the bolt onto the shelf behind it.
[2018-09-05 08:59:39] [Output] : ★ Jared Lyall disconnects the cable from the battery.
[2018-09-05 08:59:45] [Output] : ★ Jared Lyall untightens the nut on the battery's negative cable.
[2018-09-05 08:59:54] [Output] : ★ Jared Lyall unscrews the bolt on the battery's negative cable.
[2018-09-05 08:59:59] [Output] : ★ Jared Lyall places the screw and bolt next to the previous two.
[2018-09-05 09:00:05] [Output] : ★ Jared Lyall disconnects the second cable.
[2018-09-05 09:00:13] [Output] : ★ Jared Lyall removes the battery carefully from the vehicle and places it onto the -
[2018-09-05 09:00:15] [Output] : ★ - shelf behind him.      ((Jared Lyall))
[2018-09-05 09:03:31] [Output] : ★ Jared Lyall unscrews the bolts holding the frontlights in place. He then removes the frontlights.
[2018-09-05 09:03:37] [Output] : ★ Jared Lyall places the frontlights onto the shelf.
[2018-09-05 09:03:44] [Output] : ★ Jared Lyall presses a button on the lift to raise the vehicle.
[2018-09-05 09:04:45] [Output] : ★ Jared Lyall reaches under the vehicle with a screwgun. He attaches a 16mm head onto it.
[2018-09-05 09:05:46] [Output] : ★ Jared Lyall unscrews four bolts from under the right splash panel.
[2018-09-05 09:05:56] [Output] : ★ Jared Lyall removes one from under the bumper, holding the splash panel.
[2018-09-05 09:06:16] [Output] : ★ Jared Lyall pulls out the splash panel as it would be clipped in.
[2018-09-05 09:06:19] [Output] : ★ Jared Lyall removes it out entirely.
[2018-09-05 09:06:27] [Output] : ★ Jared Lyall unscrews another four bolts from under the left splash panel.
[2018-09-05 09:06:39] [Output] : ★ Jared Lyall removes the similar bolt under the bumper.
[2018-09-05 09:06:42] [Output] : ★ Jared Lyall pulls it out as well.
[2018-09-05 09:06:52] [Output] : ★ Jared Lyall places both splash panels on the shelf.
[2018-09-05 09:08:19] [Output] : ★ Jared Lyall reaches for a bolt and ratchet. He starts removing the nuts on the wheels themselves -
[2018-09-05 09:08:25] [Output] : ★ - on the outside. He does this for the front-right wheel first.      ((Jared Lyall))
[2018-09-05 09:08:34] [Output] : ★ Jared Lyall unscrews them, removes the rim, unscrews the bolts under that after ensuring the rim -
[2018-09-05 09:08:40] [Output] : ★ - is not clipped onto the wheel, then removes the wheel entirely.      ((Jared Lyall))
[2018-09-05 09:08:50] [Output] : ★ Jared Lyall repeats the process for the other, front-left wheel. He removes the bolts, then -
[2018-09-05 09:09:03] [Output] : ★ - ensures it's not clipped, then carefully places it down as the vehicle's lifted half-way -      ((Jared Lyall))
[2018-09-05 09:09:10] [Output] : ★ - and places it onto the ground, against the wall.      ((Jared Lyall))
[2018-09-05 09:09:28] [Output] : ★ Jared Lyall places a 5mm head onto the gun.
[2018-09-05 09:09:42] [Output] : ★ Jared Lyall removes four bolts from the bumper back (near the wheel).
[2018-09-05 09:10:04] [Output] : ★ Jared Lyall peels back the wheel well liner and unscrews a fifth bolt.
[2018-09-05 09:10:08] [Output] : ★ Jared Lyall places the five bolts onto the shelf.
[2018-09-05 09:10:34] [Output] : ★ Jared Lyall reaches for the other wheel. He removes four bolts from the bumper back.
[2018-09-05 09:10:40] [Output] : ★ Jared Lyall peels back the wheel well and unscrews the fifth bolt there.
[2018-09-05 09:10:58] [Output] : ★ Jared Lyall unclips the top of the bumper close to the wire on both sides.
[2018-09-05 09:11:10] [Output] : ★ Jared Lyall reaches for the 8mm head and places it onto the gun.
[2018-09-05 09:11:20] [Output] : ★ Jared Lyall removes eight 8mm bolts from under the bumper.
[2018-09-05 09:11:46] [Output] : ★ Jared Lyall lowers the vehicle a bit, he removes the weatherstripping by pulling it up, placing it -
[2018-09-05 09:11:48] [Output] : ★ - onto the shelf.      ((Jared Lyall))
[2018-09-05 09:12:07] [Output] : ★ Jared Lyall removes two t45 screws on both ends, and 6 t30 bolts in the middle.
[2018-09-05 09:12:22] [Output] : ★ Jared Lyall ensures there's nothing else connected and removes the bumper properly.
[2018-09-05 09:12:25] [Output] : ★ Jared Lyall places the bumper against the wall.
[2018-09-05 09:14:00] [Output] : ★ Jared Lyall heightens the vehicle once more.
[2018-09-05 09:14:06] [Output] : ★ Jared Lyall disconnects the temperature sensor.
[2018-09-05 09:14:30] [Output] : ★ Jared Lyall would have also removed two horn connectors as he'd remove the bumper.
[2018-09-05 09:15:39] [Output] : ★ Jared Lyall removes two bolts from underneath the front-left headlight.
[2018-09-05 09:15:42] [Output] : ★ Jared Lyall removes two bolts from uptop.
[2018-09-05 09:15:47] [Output] : ★ Jared Lyall pulls out the headlight and places it onto the shelf.
[2018-09-05 09:15:56] [Output] : ★ Jared Lyall removes two bolts from underneath the left headlight.
[2018-09-05 09:16:01] [Output] : ★ Jared Lyall removes two bolts from uptop.
[2018-09-05 09:16:07] [Output] : ★ Jared Lyall removes the second headlight.
[2018-09-05 09:16:27] [Output] : ★ Jared Lyall would disconnect the push-lock connectors as he'd remove the headlights.
[2018-09-05 09:16:37] [Output] : ★ There'd be four per headlight.      ((Jared Lyall))
[2018-09-05 09:16:42] [Output] : ★ There'd be one for the sidelight.      ((Jared Lyall))
[2018-09-05 09:16:47] [Output] : Jared Lyall: (( per* ))
[2018-09-05 09:17:28] [Output] : ★ Jared Lyall reaches behind the radiator. It'd be connected with a t25. He unscrews it.
[2018-09-05 09:17:35] [Output] : ★ Jared Lyall pulls up the radiator and places it onto the shelf.
[2018-09-05 09:17:57] [Output] : ★ Jared Lyall notices the radiator would spill. He places it ontop of a piece of cloth.
[2018-09-05 09:18:32] [Output] : ★ Jared Lyall reaches for a couple of locking wires and pulls them towards him, he pushes it -
[2018-09-05 09:18:41] [Output] : ★ - off afterwards and it will start draining after being disconnected.      ((Jared Lyall))
[2018-09-05 09:19:34] [Output] : ★ Jared Lyall starts unhooking the lines from the condensor, they are connected with 6mm allens.
[2018-09-05 09:20:21] [Output] : ★ Jared Lyall disconnects one of the lines from the top of the compressor to gain leeway.
[2018-09-05 09:21:10] [Output] : ★ Jared Lyall places the line onto the shelf.
[2018-09-05 09:21:47] [Output] : ★ Jared Lyall disconnects the other line from the dryer.
[2018-09-05 09:21:50] [Output] : ★ Jared Lyall places it onto the shelf.
[2018-09-06 02:19:52] [Output] : ★ Jared Lyall reaches for his gloves, puts them on as he continues his job.
[2018-09-06 02:19:54] [Output] : * Jared Lyall slips a pair of Gloves onto their hands. *
[2018-09-06 02:20:14] [Output] : ★ Jared Lyall removes the receiver dryer line from its position.
[2018-09-06 02:20:16] [Output] : ★ Jared Lyall places it onto the shelf.
[2018-09-06 02:21:41] [Output] : ★ Jared Lyall removes the lines from the receiver dryer that go to the expansion well.
[2018-09-06 02:22:18] [Output] : ★ Jared Lyall removes the front of the electric connector preventing the compressor from being -
[2018-09-06 02:22:21] [Output] : ★ - disconnected.      ((Jared Lyall))
[2018-09-06 02:22:32] [Output] : ★ Jared Lyall removes three bolts holding the compressor.
[2018-09-06 02:22:35] [Output] : ADVERT: Russian Standard Insurance| Business, Liability, Automotive, Theft & Homeowners Coverage!  | #111122
[2018-09-06 02:23:27] [Output] : ★ Jared Lyall leaves the top one in a bit, but it's loosened.
[2018-09-06 02:23:32] [Output] : ★ This way the AC compressor does not fall.      ((Jared Lyall))
[2018-09-06 02:24:07] [Output] : ★ Jared Lyall wiggles the compressor around, he removes the bolt and then takes the AC compressor -
[2018-09-06 02:24:19] [Output] : ★ - out, placing it onto a piece of cloth.      ((Jared Lyall))
[2018-09-06 02:24:23] [Output] : ★ It would leak oil.      ((Jared Lyall))
[2018-09-06 02:25:03] [Output] : ★ Jared Lyall pops open a plastic rivet.
[2018-09-06 02:25:12] [Output] : ★ Jared Lyall unbolts another t25 from the other side of the engine bay.
[2018-09-06 02:25:20] [Output] : ★ Jared Lyall removes the AC condensor as well.
[2018-09-06 02:25:23] [Output] : ★ Jared Lyall places it onto the shelf.
[2018-09-06 02:26:32] [Output] : ★ Jared Lyall removes four bolts from the top part of the engine bay, which the condenser -
[2018-09-06 02:26:35] [Output] : ★ - was held to.      ((Jared Lyall))
[2018-09-06 02:26:50] [Output] : ★ Jared Lyall unscerws two screws from the top part.
[2018-09-06 02:27:05] [Output] : ★ Jared Lyall slips out a cable from the top part.
[2018-09-06 02:27:54] [Output] : ★ Jared Lyall removes 3 13mm bolts and the washers attached to them from the guard.
[2018-09-06 02:28:10] [Output] : ★ Jared Lyall removes the front guard entirely. He places it against the wall.
[2018-09-06 02:28:53] [Output] : ★ Jared Lyall unbolts the air ducts by removing 2 8mm bolts.
[2018-09-06 02:28:58] [Output] : ★ Jared Lyall removes the air ducts.
[2018-09-06 02:29:12] [Output] : ★ Jared Lyall pulls out the power steering pump and disconnects the reservoir lines.
[2018-09-06 02:31:06] [Output] : ★ Jared Lyall removes the transmission mount.
[2018-09-06 02:31:15] [Output] : ★ Jared Lyall disconnects the ATF cooler lines after removing the transmission mount.
[2018-09-06 02:31:24] [Output] : ★ Jared Lyall disconnects the drive shaft.
[2018-09-06 02:31:40] [Output] : ★ Jared Lyall removes most of the bolts from the bottom of the bell housing.
[2018-09-06 02:31:47] [Output] : ★ There'd be four bolts holding the engine in place.      ((Jared Lyall))
[2018-09-06 02:32:16] [Output] : ★ Jared Lyall pulls the engine a bit forward, giving Jared some room to get the ratchet with an e14 -
[2018-09-06 02:32:33] [Output] : ★ - to get near the back of the engine and remove a bolt from it.      ((Jared Lyall))
[2018-09-06 02:32:46] [Output] : ★ Jared Lyall does that with an 11mm wrench.
[2018-09-06 02:32:58] [Output] : ★ Jared Lyall removes another bolt next to it using the 11mm wrench.
[2018-09-06 02:33:55] [Output] : ★ Jared Lyall slides the engine to the left a bit, he removes a bolt from the back-right side of the engin
[2018-09-06 02:33:56] [Output] : ★ -e.      ((Jared Lyall))
[2018-09-06 02:34:14] [Output] : ((OOC Luck)) Jared Lyall tries their luck from 1 to 100 and gets 62.
[2018-09-06 02:34:16] [Output] : ((OOC Chance at 62%)) Jared Lyall's attempt has succeeded.
[2018-09-06 02:34:27] [Output] : ★ Jared Lyall removes the bolt successfully, he does not need an extension.
[2018-09-06 02:35:41] [Output] : ★ Jared Lyall reaches for a chain, slings it through the rear.
[2018-09-06 02:35:51] [Output] : ★ Jared Lyall wraps a seatbelt on the front, he connects the chain to the seatbelt with a bolt.
[2018-09-06 02:35:57] [Output] : ★ They would be wrapped around the engine and the transmission.      ((Jared Lyall))
[2018-09-06 02:36:27] [Output] : ★ Jared Lyall hooks up the chain/seatbelt combo to a crane. He raises the crane a bit, taking some -
[2018-09-06 02:36:32] [Output] : ★ - tension away from the engine-transmission.      ((Jared Lyall))
[2018-09-06 02:37:11] [Output] : ★ Jared Lyall removes the remaining bolts now that there is less tension.
[2018-09-06 02:37:22] [Output] : ★ Jared Lyall lifts up the crane, which would now remove the engine entirely.
[2018-09-06 02:37:33] [Output] : ★ Jared Lyall slowly raises the engine, ensuring it is not connected to anything and is not damaged -
[2018-09-06 02:37:39] [Output] : ★ - in the process of removing it.      ((Jared Lyall))
[2018-09-06 02:38:15] [Output] : ★ Jared Lyall starts placing the parts into the van.
[2018-09-06 02:38:25] [Output] : ★ Jared Lyall reaches for the van, he unlocks it and opens up the back-door.
[2018-09-06 02:40:25] [Output] : ★ Jared Lyall places the front wiper-blade into the trunk.
[2018-09-06 02:40:29] [Output] : ★ Jared Lyall places the back wiper-blade into the trunk.
[2018-09-06 02:40:45] [Output] : ★ Jared Lyall places the various bulbs into the trunk in a place where they would not be damaged.
[2018-09-06 02:40:48] [Output] : ★ Jared Lyall uses a box if required.
[2018-09-06 02:41:01] [Output] : ★ Jared Lyall places the hood into the trunk.
[2018-09-06 02:41:06] [Output] : ★ Jared Lyall places the front bumper into the truck.
[2018-09-06 02:41:17] [Output] : ★ Jared Lyall places the battery into the truck.
[2018-09-06 02:41:34] [Output] : ★ Jared Lyall places the headlights into the truck.
[2018-09-06 02:41:38] [Output] : ★ Jared Lyall places the xenon lights into the truck.
[2018-09-06 02:41:41] [Output] : ★ Jared Lyall places the backlights into the truck.
[2018-09-06 02:41:54] [Output] : ★ Jared Lyall places the splash panels into the truck.
[2018-09-06 02:42:05] [Output] : ★ Jared Lyall places the rims into the truck.
[2018-09-06 02:42:11] [Output] : ★ Jared Lyall reaches for the wheels, one at a time.
[2018-09-06 02:42:15] [Output] : ★ Jared Lyall rolls the wheel over towards the truck.
[2018-09-06 02:42:22] [Output] : ★ Jared Lyall slowly lifts it up, and carefully places it into the truck.
[2018-09-06 02:42:26] [Output] : ★ Jared Lyall does so with the other three wheels.
[2018-09-06 02:42:59] [Output] : ★ Jared Lyall places the radiator into the truck after it's fully leaked.
[2018-09-06 02:43:09] [Output] : ★ Jared Lyall places the AC compressor and the condensor into the truck.
[2018-09-06 02:43:35] [Output] : ★ Jared Lyall places the power steering pump into the truck.
[2018-09-06 02:44:13] [Output] : ★ Jared Lyall reaches for the crane, he moves the engine into the truck and slowly places it there.
[2018-09-06 02:45:27] [Output] : ★ Jared Lyall enters the BMW, and hops onto the driver seat.
[2018-09-06 02:45:51] [Output] : ★ Jared Lyall places a plastic wedgie under the AC conditioning vent.
[2018-09-06 02:45:55] [Output] : ★ Jared Lyall pops it out.
[2018-09-06 02:46:00] [Output] : ★ Jared Lyall removes two screws from under the AC vent.
[2018-09-06 02:46:09] [Output] : ★ Jared Lyall removes the display unit, removing two plugs from the back.
[2018-09-06 02:46:18] [Output] : ★ Jared Lyall removes the plugs from the AC vent.
[2018-09-06 02:46:31] [Output] : ★ Jared Lyall places the AC vent and the display unit into the truck.
[2018-09-06 02:47:41] [Output] : ★ Jared Lyall moves both front-seats as far as forward as they get.
[2018-09-06 02:48:04] [Output] : ★ Jared Lyall removes four t50 bolts from under the seats on their pathway and removes a -
[2018-09-06 02:48:09] [Output] : ★ - couple of electric wire connections.      ((Jared Lyall))
[2018-09-06 02:48:47] [Output] : ★ Jared Lyall removes a shorter t50 bolt from the seatbelt.
[2018-09-06 02:48:58] [Output] : ★ Jared Lyall pushes the seats back as far as they'll go.
[2018-09-06 02:49:08] [Output] : ADVERT: Looking to buy a modifed vehicle sms if you have one.   | #464686
[2018-09-06 02:49:08] [Output] : ★ Jared Lyall removes two bolts from the front of the seats' pathway.
[2018-09-06 02:49:45] [Output] : ★ Jared Lyall slides the latch down and removes a wire connecting the seat to the seatbelt.
[2018-09-06 02:50:12] [Output] : ★ Jared Lyall removes the socket from the seats, the seats are now fully disconnected.
[2018-09-06 02:50:19] [Output] : ★ Jared Lyall opens the door completely.
[2018-09-06 02:50:25] [Output] : ★ Jared Lyall reaches for the seat, slowly carrying it to the truck.
[2018-09-06 02:50:30] [Output] : ★ Jared Lyall places the seat into the truck.
[2018-09-06 02:50:40] [Output] : ★ Jared Lyall reaches for the other seat, opening the passenger door entirely, and places the -
[2018-09-06 02:50:42] [Output] : ★ - seat into the truck.      ((Jared Lyall))