API tools faq
paste
Advertisement
chainsol

Two sets of multiple runs

chainsol
May 21st, 2018
162
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 11.78 KB | None | 0 0
raw download clone embed print report
  1.  
  2. Configured MCU 'z' (660 moves)
  3. Loaded MCU 'z' 60 commands (v0.6.0-61-gf70fefa-20180508_003820-octopi / gcc: (GCC) 4.8.1 binutils: (GNU Binutils) 2.24)
  4. MCU 'z' config: ADC_MAX=1023 PWM_MAX=255 CLOCK_FREQ=16000000 SOFT_PWM_MAX=256 SERIAL_BAUD=250000 MCU=atmega2560 STATS_SUMSQ_BASE=256
  5. Starting heater checks for heater_bed
  6. Starting heater checks for extruder
  7.  
  8. Restarting printer
  9. Start printer at Mon May 21 22:33:29 2018 (1526956409.5 12505.7)
  10. ===== Config file =====
  11. [stepper_x]
  12. step_pin = ar54
  13. dir_pin = !ar55
  14. enable_pin = !ar38
  15. step_distance = 0.005011
  16. endstop_pin = ^!ar3
  17. position_endstop = 0
  18. position_max = 282
  19. homing_speed = 45
  20.  
  21. [stepper_y]
  22. step_pin = ar46
  23. dir_pin = ar48
  24. enable_pin = !ar62
  25. step_distance = 0.005011
  26. endstop_pin = ^!ar14
  27. position_endstop = 0
  28. position_max = 300
  29. homing_speed = 45
  30.  
  31. [stepper_z]
  32. step_pin = z:ar54
  33. dir_pin = z:ar55
  34. enable_pin = !z:ar38
  35. step_distance = 0.000313
  36. endstop_pin = probe:z_virtual_endstop
  37. position_endstop = 1.7
  38. position_max = 300
  39. position_min = -0.35
  40. homing_speed = 4
  41.  
  42. [stepper_z1]
  43. step_pin = z:ar60
  44. dir_pin = z:ar61
  45. enable_pin = !z:ar56
  46. step_distance = 0.000313
  47.  
  48. [stepper_z2]
  49. step_pin = z:ar46
  50. dir_pin = z:ar48
  51. enable_pin = !z:ar62
  52. step_distance = 0.000313
  53.  
  54. [extruder]
  55. step_pin = ar26
  56. dir_pin = ar28
  57. enable_pin = !ar24
  58. step_distance = 0.001150
  59. nozzle_diameter = 0.400
  60. pressure_advance = 0.05
  61. filament_diameter = 1.750
  62. heater_pin = ar10
  63. sensor_type = ATC Semitec 104GT-2
  64. sensor_pin = analog13
  65. control = pid
  66. pid_kp = 16.459
  67. pid_ki = 1.291
  68. pid_kd = 52.465
  69. min_temp = 0
  70. max_temp = 300
  71.  
  72. [heater_bed]
  73. heater_pin = ar8
  74. sensor_type = EPCOS 100K B57560G104F
  75. sensor_pin = analog14
  76. control = pid
  77. pid_kp = 47.076
  78. pid_ki = 0.659
  79. pid_kd = 840.308
  80. min_temp = 0
  81. max_temp = 130
  82.  
  83. [servo bltouch]
  84. pin = z:ar11
  85. maximum_servo_angle = 180
  86. minimum_pulse_width = 0.0006
  87. maximum_pulse_width = 0.0024
  88.  
  89. [probe]
  90. pin = z:ar19
  91. z_offset = 1.7
  92. activate_gcode =
  93. SET_SERVO SERVO=bltouch ANGLE=10
  94. SET_SERVO SERVO=bltouch ANGLE=60
  95. G4 P200
  96. deactivate_gcode =
  97. SET_SERVO SERVO=bltouch ANGLE=90
  98.  
  99. [homing_override]
  100. set_position_z = 5
  101. gcode =
  102. G90
  103. G1 Z7 F600
  104. G28 X0 Y0
  105. G1 X150 Y150 F3600
  106. G28 Z0
  107. G1 X0 Y0 F3600
  108.  
  109. [z_tilt]
  110. z_positions =
  111. -56.17,0
  112. -56.17,235
  113. 362.43,103
  114. points =
  115. 10,21
  116. 10,210
  117. 282,103
  118. horizontal_move_z = 8
  119.  
  120. [fan]
  121. pin = ar9
  122.  
  123. [mcu z]
  124. serial = /dev/serial/by-path/platform-3f980000.usb-usb-0:1.2:1.0-port0
  125. pin_map = arduino
  126.  
  127. [mcu]
  128. serial = /dev/serial/by-path/platform-3f980000.usb-usb-0:1.3:1.0-port0
  129. pin_map = arduino
  130.  
  131. [printer]
  132. kinematics = corexy
  133. max_velocity = 1600
  134. max_accel = 3000
  135. max_z_velocity = 8
  136. max_z_accel = 50
  137.  
  138. =======================
  139. Starting serial connect
  140.  
  141. Attempting MCU 'mcu' reset
  142. Attempting MCU 'z' reset
  143. Restarting printer
  144. Start printer at Mon May 21 22:33:32 2018 (1526956412.1 12508.3)
  145. ===== Config file =====
  146. [stepper_x]
  147. step_pin = ar54
  148. dir_pin = !ar55
  149. enable_pin = !ar38
  150. step_distance = 0.005011
  151. endstop_pin = ^!ar3
  152. position_endstop = 0
  153. position_max = 282
  154. homing_speed = 45
  155.  
  156. [stepper_y]
  157. step_pin = ar46
  158. dir_pin = ar48
  159. enable_pin = !ar62
  160. step_distance = 0.005011
  161. endstop_pin = ^!ar14
  162. position_endstop = 0
  163. position_max = 300
  164. homing_speed = 45
  165.  
  166. [stepper_z]
  167. step_pin = z:ar54
  168. dir_pin = z:ar55
  169. enable_pin = !z:ar38
  170. step_distance = 0.000313
  171. endstop_pin = probe:z_virtual_endstop
  172. position_endstop = 1.7
  173. position_max = 300
  174. position_min = -0.35
  175. homing_speed = 4
  176.  
  177. [stepper_z1]
  178. step_pin = z:ar60
  179. dir_pin = z:ar61
  180. enable_pin = !z:ar56
  181. step_distance = 0.000313
  182.  
  183. [stepper_z2]
  184. step_pin = z:ar46
  185. dir_pin = z:ar48
  186. enable_pin = !z:ar62
  187. step_distance = 0.000313
  188.  
  189. [extruder]
  190. step_pin = ar26
  191. dir_pin = ar28
  192. enable_pin = !ar24
  193. step_distance = 0.001150
  194. nozzle_diameter = 0.400
  195. pressure_advance = 0.05
  196. filament_diameter = 1.750
  197. heater_pin = ar10
  198. sensor_type = ATC Semitec 104GT-2
  199. sensor_pin = analog13
  200. control = pid
  201. pid_kp = 16.459
  202. pid_ki = 1.291
  203. pid_kd = 52.465
  204. min_temp = 0
  205. max_temp = 300
  206.  
  207. [heater_bed]
  208. heater_pin = ar8
  209. sensor_type = EPCOS 100K B57560G104F
  210. sensor_pin = analog14
  211. control = pid
  212. pid_kp = 47.076
  213. pid_ki = 0.659
  214. pid_kd = 840.308
  215. min_temp = 0
  216. max_temp = 130
  217.  
  218. [servo bltouch]
  219. pin = z:ar11
  220. maximum_servo_angle = 180
  221. minimum_pulse_width = 0.0006
  222. maximum_pulse_width = 0.0024
  223.  
  224. [probe]
  225. pin = z:ar19
  226. z_offset = 1.7
  227. activate_gcode =
  228. SET_SERVO SERVO=bltouch ANGLE=10
  229. SET_SERVO SERVO=bltouch ANGLE=60
  230. G4 P200
  231. deactivate_gcode =
  232. SET_SERVO SERVO=bltouch ANGLE=90
  233.  
  234. [homing_override]
  235. set_position_z = 5
  236. gcode =
  237. G90
  238. G1 Z7 F600
  239. G28 X0 Y0
  240. G1 X150 Y150 F3600
  241. G28 Z0
  242. G1 X0 Y0 F3600
  243.  
  244. [z_tilt]
  245. z_positions =
  246. -56.17,0
  247. -56.17,235
  248. 362.43,103
  249. points =
  250. 10,21
  251. 10,210
  252. 282,103
  253. horizontal_move_z = 8
  254.  
  255. [fan]
  256. pin = ar9
  257.  
  258. [mcu z]
  259. serial = /dev/serial/by-path/platform-3f980000.usb-usb-0:1.2:1.0-port0
  260. pin_map = arduino
  261.  
  262. [mcu]
  263. serial = /dev/serial/by-path/platform-3f980000.usb-usb-0:1.3:1.0-port0
  264. pin_map = arduino
  265.  
  266. [printer]
  267. kinematics = corexy
  268. max_velocity = 1600
  269. max_accel = 3000
  270. max_z_velocity = 8
  271. max_z_accel = 50
  272.  
  273. =======================
  274. Starting serial connect
  275.  
  276. Printer is not ready
  277. The klippy host software is attempting to connect. Please
  278. retry in a few moments.
  279.  
  280. Sending MCU 'mcu' printer configuration...
  281. Configured MCU 'mcu' (643 moves)
  282. Loaded MCU 'mcu' 60 commands (v0.6.0-61-gf70fefa-20180508_003820-octopi / gcc: (GCC) 4.8.1 binutils: (GNU Binutils) 2.24)
  283. MCU 'mcu' config: ADC_MAX=1023 PWM_MAX=255 CLOCK_FREQ=16000000 SOFT_PWM_MAX=256 SERIAL_BAUD=250000 MCU=atmega2560 STATS_SUMSQ_BASE=256
  284. Starting serial connect
  285.  
  286. Printer is not ready
  287. The klippy host software is attempting to connect. Please
  288. retry in a few moments.
  289.  
  290. Sending MCU 'z' printer configuration...
  291. Configured MCU 'z' (660 moves)
  292. Loaded MCU 'z' 60 commands (v0.6.0-61-gf70fefa-20180508_003820-octopi / gcc: (GCC) 4.8.1 binutils: (GNU Binutils) 2.24)
  293. MCU 'z' config: ADC_MAX=1023 PWM_MAX=255 CLOCK_FREQ=16000000 SOFT_PWM_MAX=256 SERIAL_BAUD=250000 MCU=atmega2560 STATS_SUMSQ_BASE=256
  294. Starting heater checks for heater_bed
  295. Starting heater checks for extruder
  296.  
  297. Calculating bed tilt with: [[10.000176499999998, 20.9993215, 2.0349099999999996], [10.000176499999995, 209.9992085, 1.9704319999999995], [281.999762, 103.00183099999998, 1.4320719999999993]]
  298. Coordinate descent best_err: 1.85144942381e-10 rounds: 184
  299. Calculated bed tilt parameters: {'y_adjust': -0.0003412422554932085, 'x_adjust': -0.002113501722782265, 'z_adjust': 2.0632212880401006}
  300.  
  301. Calculating bed tilt with: [[10.000176499999998, 20.9993215, 2.332886], [10.000176499999995, 209.9992085, 2.341963], [281.999762, 103.00183099999998, 1.0915279999999994]]
  302. Coordinate descent best_err: 5.44439634087e-11 rounds: 194
  303. Calculated bed tilt parameters: {'y_adjust': 4.802479561316352e-05, 'x_adjust': -0.004578334139563691, 'z_adjust': 2.377663526053874}
  304.  
  305. Calculating bed tilt with: [[10.000176499999998, 20.9993215, 3.079077999999999], [10.000176499999995, 209.9992085, 3.0656189999999985], [281.999762, 103.00183099999998, 0.4204559999999984]]
  306. Coordinate descent best_err: 2.12600761192e-10 rounds: 196
  307. Calculated bed tilt parameters: {'y_adjust': -7.116593338050959e-05, 'x_adjust': -0.009752939922191048, 'z_adjust': 3.1780997407254645}
  308.  
  309. Restarting printer
  310. Start printer at Mon May 21 22:38:35 2018 (1526956715.8 12812.1)
  311. ===== Config file =====
  312. [stepper_x]
  313. step_pin = ar54
  314. dir_pin = !ar55
  315. enable_pin = !ar38
  316. step_distance = 0.005011
  317. endstop_pin = ^!ar3
  318. position_endstop = 0
  319. position_max = 282
  320. homing_speed = 45
  321.  
  322. [stepper_y]
  323. step_pin = ar46
  324. dir_pin = ar48
  325. enable_pin = !ar62
  326. step_distance = 0.005011
  327. endstop_pin = ^!ar14
  328. position_endstop = 0
  329. position_max = 300
  330. homing_speed = 45
  331.  
  332. [stepper_z]
  333. step_pin = z:ar54
  334. dir_pin = z:ar55
  335. enable_pin = !z:ar38
  336. step_distance = 0.000313
  337. endstop_pin = probe:z_virtual_endstop
  338. position_endstop = 1.7
  339. position_max = 300
  340. position_min = -0.35
  341. homing_speed = 4
  342.  
  343. [stepper_z1]
  344. step_pin = z:ar60
  345. dir_pin = z:ar61
  346. enable_pin = !z:ar56
  347. step_distance = 0.000313
  348.  
  349. [stepper_z2]
  350. step_pin = z:ar46
  351. dir_pin = z:ar48
  352. enable_pin = !z:ar62
  353. step_distance = 0.000313
  354.  
  355. [extruder]
  356. step_pin = ar26
  357. dir_pin = ar28
  358. enable_pin = !ar24
  359. step_distance = 0.001150
  360. nozzle_diameter = 0.400
  361. pressure_advance = 0.05
  362. filament_diameter = 1.750
  363. heater_pin = ar10
  364. sensor_type = ATC Semitec 104GT-2
  365. sensor_pin = analog13
  366. control = pid
  367. pid_kp = 16.459
  368. pid_ki = 1.291
  369. pid_kd = 52.465
  370. min_temp = 0
  371. max_temp = 300
  372.  
  373. [heater_bed]
  374. heater_pin = ar8
  375. sensor_type = EPCOS 100K B57560G104F
  376. sensor_pin = analog14
  377. control = pid
  378. pid_kp = 47.076
  379. pid_ki = 0.659
  380. pid_kd = 840.308
  381. min_temp = 0
  382. max_temp = 130
  383.  
  384. [servo bltouch]
  385. pin = z:ar11
  386. maximum_servo_angle = 180
  387. minimum_pulse_width = 0.0006
  388. maximum_pulse_width = 0.0024
  389.  
  390. [probe]
  391. pin = z:ar19
  392. z_offset = 1.7
  393. activate_gcode =
  394. SET_SERVO SERVO=bltouch ANGLE=10
  395. SET_SERVO SERVO=bltouch ANGLE=60
  396. G4 P200
  397. deactivate_gcode =
  398. SET_SERVO SERVO=bltouch ANGLE=90
  399.  
  400. [homing_override]
  401. set_position_z = 5
  402. gcode =
  403. G90
  404. G1 Z7 F600
  405. G28 X0 Y0
  406. G1 X10 Y0 F3600
  407. G28 Z0
  408. G1 X0 Y0 F3600
  409.  
  410. [z_tilt]
  411. z_positions =
  412. -56.17,0
  413. -56.17,235
  414. 362.43,103
  415. points =
  416. 10,21
  417. 10,210
  418. 282,103
  419. horizontal_move_z = 8
  420.  
  421. [fan]
  422. pin = ar9
  423.  
  424. [mcu z]
  425. serial = /dev/serial/by-path/platform-3f980000.usb-usb-0:1.2:1.0-port0
  426. pin_map = arduino
  427.  
  428. [mcu]
  429. serial = /dev/serial/by-path/platform-3f980000.usb-usb-0:1.3:1.0-port0
  430. pin_map = arduino
  431.  
  432. [printer]
  433. kinematics = corexy
  434. max_velocity = 1600
  435. max_accel = 3000
  436. max_z_velocity = 8
  437. max_z_accel = 50
  438.  
  439. =======================
  440. Starting serial connect
  441.  
  442. Printer is not ready
  443. The klippy host software is attempting to connect. Please
  444. retry in a few moments.
  445.  
  446. got {'#receive_time': 12813.254195819, u'next_clock': 585512704, u'oid': 3, u'value': 7860, '#name': u'analog_in_state', '#sent_time': 12813.200461040999}
  447. got {'#receive_time': 12813.324437883999, u'next_clock': 586632704, u'oid': 10, u'value': 7847, '#name': u'analog_in_state', '#sent_time': 12813.302610593}
  448. Configured MCU 'mcu' (643 moves)
  449. Loaded MCU 'mcu' 60 commands (v0.6.0-61-gf70fefa-20180508_003820-octopi / gcc: (GCC) 4.8.1 binutils: (GNU Binutils) 2.24)
  450. MCU 'mcu' config: ADC_MAX=1023 PWM_MAX=255 CLOCK_FREQ=16000000 SOFT_PWM_MAX=256 SERIAL_BAUD=250000 MCU=atmega2560 STATS_SUMSQ_BASE=256
  451. Starting serial connect
  452.  
  453. Printer is not ready
  454. The klippy host software is attempting to connect. Please
  455. retry in a few moments.
  456.  
  457. Configured MCU 'z' (660 moves)
  458. Loaded MCU 'z' 60 commands (v0.6.0-61-gf70fefa-20180508_003820-octopi / gcc: (GCC) 4.8.1 binutils: (GNU Binutils) 2.24)
  459. MCU 'z' config: ADC_MAX=1023 PWM_MAX=255 CLOCK_FREQ=16000000 SOFT_PWM_MAX=256 SERIAL_BAUD=250000 MCU=atmega2560 STATS_SUMSQ_BASE=256
  460. Starting heater checks for heater_bed
  461. Starting heater checks for extruder
  462.  
  463. Calculating bed tilt with: [[10.0, 21.001101, 1.7453849999999997], [10.000000000000014, 210.000988, 1.7766849999999994], [281.99958549999997, 102.99859949999998, 2.1150379999999993]]
  464. Coordinate descent best_err: 6.10538462332e-11 rounds: 194
  465. Calculated bed tilt parameters: {'y_adjust': 0.00016561416593453346, 'x_adjust': 0.0013090986005706738, 'z_adjust': 1.7288196517978136}
  466.  
  467. Calculating bed tilt with: [[10.0, 21.001101, 1.7510189999999997], [10.000000000000014, 210.000988, 1.7491409999999994], [281.99958549999997, 102.99859949999998, 2.5003409999999993]]
  468. Coordinate descent best_err: 7.54491262732e-11 rounds: 194
  469. Calculated bed tilt parameters: {'y_adjust': -9.922398647434168e-06, 'x_adjust': 0.0027578253110784605, 'z_adjust': 1.7236491341729392}
  470.  
  471. Calculating bed tilt with: [[10.0, 21.001101, 1.7363079999999997], [10.000000000000014, 210.000988, 1.7694859999999997], [281.99958549999997, 102.99859949999998, 3.3635949999999992]]
  472. Coordinate descent best_err: 1.11295973795e-10 rounds: 198
  473. Calculated bed tilt parameters: {'y_adjust': 0.00017557740343542778, 'x_adjust': 0.005929723182174362, 'z_adjust': 1.6733261442817302}
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!