INFO  | ??:??:?? 1

//\ E S H T /\ S T / C

DEBUG | ??:??:?? 1 Filesystem files:
DEBUG | ??:??:?? 1  prefs (directory)
DEBUG | ??:??:?? 1    channels.proto (59 Bytes)
DEBUG | ??:??:?? 1    device.proto (135 Bytes)
DEBUG | ??:??:?? 1    module.proto (119 Bytes)
DEBUG | ??:??:?? 1    nodes.proto (276 Bytes)
DEBUG | ??:??:?? 1    config.proto (226 Bytes)
DEBUG | ??:??:?? 1  adafruit (directory)
DEBUG | ??:??:?? 1  bond_prph (directory)
DEBUG | ??:??:?? 1  bond_cntr (directory)
DEBUG | ??:??:?? 1 Power::lipoInit lipo sensor is not ready yet
DEBUG | ??:??:?? 1 Use analog input 31 for battery level
INFO  | ??:??:?? 1 Scan for i2c devices
DEBUG | ??:??:?? 1 Scan for I2C devices on port 1
INFO  | ??:??:?? 1 AHT10 found at address 0x38
INFO  | ??:??:?? 1 1 I2C devices found
DEBUG | ??:??:?? 1 acc_info = 0
INFO  | ??:??:?? 1 S:B:255,2.7.15.d18f3f7a6,WashTastic,meshtastic/firmware
INFO  | ??:??:?? 1 Build timestamp: 1765227600
DEBUG | ??:??:?? 1 Reset reason: 0x0
DEBUG | ??:??:?? 1 Set random seed 675358391
INFO  | ??:??:?? 1 Init NodeDB
INFO  | ??:??:?? 1 Load /prefs/nodes.proto
INFO  | ??:??:?? 1 Loaded /prefs/nodes.proto successfully
INFO  | ??:??:?? 1 Loaded saved nodedatabase version 24, with nodes count: 1
INFO  | ??:??:?? 1 Load /prefs/device.proto
INFO  | ??:??:?? 1 Loaded /prefs/device.proto successfully
INFO  | ??:??:?? 1 Loaded saved devicestate version 24
INFO  | ??:??:?? 1 Load /prefs/config.proto
INFO  | ??:??:?? 1 Loaded /prefs/config.proto successfully
INFO  | ??:??:?? 1 Loaded saved config version 24
INFO  | ??:??:?? 1 Load /prefs/module.proto
INFO  | ??:??:?? 1 Loaded /prefs/module.proto successfully
INFO  | ??:??:?? 1 Loaded saved moduleConfig version 24
INFO  | ??:??:?? 1 Load /prefs/channels.proto
INFO  | ??:??:?? 1 Loaded /prefs/channels.proto successfully
INFO  | ??:??:?? 1 Loaded saved channelFile version 24
ERROR | ??:??:?? 1 Could not open / read /prefs/uiconfig.proto
DEBUG | ??:??:?? 1 cleanupMeshDB purged 0 entries
DEBUG | ??:??:?? 1 Use nodenum 0x167abf61
DEBUG | ??:??:?? 1 Expand short PSK #1
INFO  | ??:??:?? 1 Wanted region 1, using US
DEBUG | ??:??:?? 1 Coerce telemetry to min of 30 minutes on defaults
INFO  | ??:??:?? 1 Sort took 0 milliseconds
DEBUG | ??:??:?? 1 Save to disk 0
WARN  | ??:??:?? 1 Packet History - Invalid size -1, using default 160
DEBUG | ??:??:?? 1 Use compiled/slipstreamed tzplaceholder
DEBUG | ??:??:?? 1 Saved TZ: PST8PDT,M3.2.0/2:00:00,M11.1.0/2:00:00
DEBUG | ??:??:?? 1 Set Timezone to PST8PDT,M3.2.0/2:00:00,M11.1.0/2:00:00
DEBUG | ??:??:?? 1 Rescan for I2C keyboard
DEBUG | ??:??:?? 1 Scan for I2C devices on port 1
DEBUG | ??:??:?? 1 Scan address 0x1f
DEBUG | ??:??:?? 1 Scan address 0x34
DEBUG | ??:??:?? 1 Scan address 0x55
DEBUG | ??:??:?? 1 Scan address 0x5a
DEBUG | ??:??:?? 1 Scan address 0x5f
ERROR | ??:??:?? 1 Could not open / read /prefs/cannedConf.proto
INFO  | ??:??:?? 1 CannedMessageModule is enabled
INFO  | ??:??:?? 1 External Notification Module Disabled
DEBUG | ??:??:?? 1 RF95Interface(cs=45, irq=29, rst=9, busy=10)
INFO  | ??:??:?? 1 Start meshradio init
INFO  | ??:??:?? 1 Radio freq=906.875, config.lora.frequency_offset=0.000
INFO  | ??:??:?? 1 Set radio: region=US, name=LongFast, config=0, ch=19, power=30
INFO  | ??:??:?? 1 myRegion->freqStart -> myRegion->freqEnd: 902.000000 -> 928.000000 (26.000000 MHz)
INFO  | ??:??:?? 1 numChannels: 104 x 250.000kHz
INFO  | ??:??:?? 1 channel_num: 20
INFO  | ??:??:?? 1 frequency: 906.875000
INFO  | ??:??:?? 1 Slot time: 28 msec, preamble time: 131 msec
INFO  | ??:??:?? 1 Requested Tx power: 30 dBm; Device LoRa Tx gain: 7 dB
INFO  | ??:??:?? 1 Final Tx power: 20 dBm
INFO  | ??:??:?? 2 RF95 init result -2
INFO  | ??:??:?? 2 Frequency set to 906.875000
INFO  | ??:??:?? 2 Bandwidth set to 250.000000
INFO  | ??:??:?? 2 Power output set to 20
WARN  | ??:??:?? 2 No RF95 radio
DEBUG | ??:??:?? 2 SX126xInterface(cs=45, irq=10, rst=9, busy=29)
DEBUG | ??:??:?? 2 SX126X_DIO3_TCXO_VOLTAGE defined, using DIO3 as TCXO reference voltage at 1.800000 V
INFO  | ??:??:?? 2 Start meshradio init
INFO  | ??:??:?? 2 Radio freq=906.875, config.lora.frequency_offset=0.000
INFO  | ??:??:?? 2 Set radio: region=US, name=LongFast, config=0, ch=19, power=30
INFO  | ??:??:?? 2 myRegion->freqStart -> myRegion->freqEnd: 902.000000 -> 928.000000 (26.000000 MHz)
INFO  | ??:??:?? 2 numChannels: 104 x 250.000kHz
INFO  | ??:??:?? 2 channel_num: 20
INFO  | ??:??:?? 2 frequency: 906.875000
INFO  | ??:??:?? 2 Slot time: 28 msec, preamble time: 131 msec
INFO  | ??:??:?? 2 Requested Tx power: 30 dBm; Device LoRa Tx gain: 7 dB
INFO  | ??:??:?? 2 Final Tx power: 22 dBm
INFO  | ??:??:?? 2 SX126x init result -707
WARN  | ??:??:?? 2 No SX1262 radio with TCXO, Vref 1.800000V
DEBUG | ??:??:?? 2 SX126xInterface(cs=45, irq=10, rst=9, busy=29)
DEBUG | ??:??:?? 2 SX126X_DIO3_TCXO_VOLTAGE not defined, not using DIO3 as TCXO reference voltage
INFO  | ??:??:?? 2 Start meshradio init
INFO  | ??:??:?? 2 Radio freq=906.875, config.lora.frequency_offset=0.000
INFO  | ??:??:?? 2 Set radio: region=US, name=LongFast, config=0, ch=19, power=30
INFO  | ??:??:?? 2 myRegion->freqStart -> myRegion->freqEnd: 902.000000 -> 928.000000 (26.000000 MHz)
INFO  | ??:??:?? 2 numChannels: 104 x 250.000kHz
INFO  | ??:??:?? 2 channel_num: 20
INFO  | ??:??:?? 2 frequency: 906.875000
INFO  | ??:??:?? 2 Slot time: 28 msec, preamble time: 131 msec
INFO  | ??:??:?? 2 Requested Tx power: 30 dBm; Device LoRa Tx gain: 7 dB
INFO  | ??:??:?? 2 Final Tx power: 22 dBm
INFO  | ??:??:?? 2 SX126x init result -707
WARN  | ??:??:?? 2 No SX1262 radio with XTAL, Vref 0.0V
DEBUG | ??:??:?? 2 SX126xInterface(cs=45, irq=10, rst=9, busy=29)
DEBUG | ??:??:?? 2 SX126X_DIO3_TCXO_VOLTAGE defined, using DIO3 as TCXO reference voltage at 1.800000 V
INFO  | ??:??:?? 2 Start meshradio init
INFO  | ??:??:?? 2 Radio freq=906.875, config.lora.frequency_offset=0.000
INFO  | ??:??:?? 2 Set radio: region=US, name=LongFast, config=0, ch=19, power=30
INFO  | ??:??:?? 2 myRegion->freqStart -> myRegion->freqEnd: 902.000000 -> 928.000000 (26.000000 MHz)
INFO  | ??:??:?? 2 numChannels: 104 x 250.000kHz
INFO  | ??:??:?? 2 channel_num: 20
INFO  | ??:??:?? 2 frequency: 433.125000
INFO  | ??:??:?? 2 Slot time: 28 msec, preamble time: 131 msec
INFO  | ??:??:?? 2 Requested Tx power: 30 dBm; Device LoRa Tx gain: 7 dB
INFO  | ??:??:?? 2 Final Tx power: 22 dBm
INFO  | ??:??:?? 2 SX126x init result -2
WARN  | ??:??:?? 2 No SX1268 radio with TCXO, Vref 1.800000V
DEBUG | ??:??:?? 2 SX126xInterface(cs=45, irq=10, rst=9, busy=29)
DEBUG | ??:??:?? 2 SX126X_DIO3_TCXO_VOLTAGE not defined, not using DIO3 as TCXO reference voltage
INFO  | ??:??:?? 2 Start meshradio init
INFO  | ??:??:?? 2 Radio freq=906.875, config.lora.frequency_offset=0.000
INFO  | ??:??:?? 2 Set radio: region=US, name=LongFast, config=0, ch=19, power=30
INFO  | ??:??:?? 2 myRegion->freqStart -> myRegion->freqEnd: 902.000000 -> 928.000000 (26.000000 MHz)
INFO  | ??:??:?? 2 numChannels: 104 x 250.000kHz
INFO  | ??:??:?? 2 channel_num: 20
INFO  | ??:??:?? 2 frequency: 433.125000
INFO  | ??:??:?? 2 Slot time: 28 msec, preamble time: 131 msec
INFO  | ??:??:?? 2 Requested Tx power: 30 dBm; Device LoRa Tx gain: 7 dB
INFO  | ??:??:?? 2 Final Tx power: 22 dBm
INFO  | ??:??:?? 2 SX126x init result -2
WARN  | ??:??:?? 2 No SX1268 radio
DEBUG | ??:??:?? 2 SX126xInterface(cs=45, irq=10, rst=9, busy=29)
DEBUG | ??:??:?? 2 SX126X_DIO3_TCXO_VOLTAGE not defined, not using DIO3 as TCXO reference voltage
INFO  | ??:??:?? 2 Start meshradio init
INFO  | ??:??:?? 2 Radio freq=906.875, config.lora.frequency_offset=0.000
INFO  | ??:??:?? 2 Set radio: region=US, name=LongFast, config=0, ch=19, power=30
INFO  | ??:??:?? 2 myRegion->freqStart -> myRegion->freqEnd: 902.000000 -> 928.000000 (26.000000 MHz)
INFO  | ??:??:?? 2 numChannels: 104 x 250.000kHz
INFO  | ??:??:?? 2 channel_num: 20
INFO  | ??:??:?? 2 frequency: 906.875000
INFO  | ??:??:?? 2 Slot time: 28 msec, preamble time: 131 msec
INFO  | ??:??:?? 2 Requested Tx power: 30 dBm; Device LoRa Tx gain: 7 dB
INFO  | ??:??:?? 2 Final Tx power: 22 dBm
INFO  | ??:??:?? 2 SX126x init result -707
WARN  | ??:??:?? 2 No LLCC68 radio
WARN  | ??:??:?? 2 LR11x0Interface(cs=45, irq=10, rst=9, busy=29)
DEBUG | ??:??:?? 2 LR11X0_DIO3_TCXO_VOLTAGE defined, using DIO3 as TCXO reference voltage at 1.800000 V
INFO  | ??:??:?? 2 Start meshradio init
INFO  | ??:??:?? 2 Radio freq=906.875, config.lora.frequency_offset=0.000
INFO  | ??:??:?? 2 Set radio: region=US, name=LongFast, config=0, ch=19, power=30
INFO  | ??:??:?? 2 myRegion->freqStart -> myRegion->freqEnd: 902.000000 -> 928.000000 (26.000000 MHz)
INFO  | ??:??:?? 2 numChannels: 104 x 250.000kHz
INFO  | ??:??:?? 2 channel_num: 20
INFO  | ??:??:?? 2 frequency: 906.875000
INFO  | ??:??:?? 2 Slot time: 28 msec, preamble time: 131 msec
INFO  | ??:??:?? 2 Requested Tx power: 30 dBm; Device LoRa Tx gain: 7 dB
INFO  | ??:??:?? 2 Final Tx power: 22 dBm
INFO  | ??:??:?? 6 LR11x0 init result -2
WARN  | ??:??:?? 6 No LR1121 radio
DEBUG | ??:??:?? 6 Init MQTT
INFO  | ??:??:?? 6 MQTT configured to use client proxy
ERROR | ??:??:?? 6 NOTE! Record critical error 3 at src/main.cpp:1467
INFO  | ??:??:?? 6 PowerFSM init, USB power=1
DEBUG | ??:??:?? 6 State: BOOT
DEBUG | ??:??:?? 6 Node status update: 1 online, 1 total
INFO  | ??:??:?? 9 [PowerFSM] Loss of power in Powered
INFO  | ??:??:?? 9 [PowerFSM] Loss of power in Powered
DEBUG | ??:??:?? 9 [PowerFSM] Init NRF52 Bluetooth
INFO  | ??:??:?? 9 [PowerFSM] Init the Bluefruit nRF52 module
INFO  | ??:??:?? 9 [PowerFSM] Bluetooth pin set to '123456'
INFO  | ??:??:?? 9 [PowerFSM] Init the Device Information Service
INFO  | ??:??:?? 9 [PowerFSM] Init the Battery Service
INFO  | ??:??:?? 9 [PowerFSM] Init the Mesh bluetooth service
INFO  | ??:??:?? 9 [PowerFSM] Set up the advertising payload(s)
INFO  | ??:??:?? 9 [PowerFSM] Advertise
DEBUG | ??:??:?? 9 [PowerFSM] State: ON
INFO  | ??:??:?? 31 [NodeInfo] Send our nodeinfo to mesh (wantReplies=0)
INFO  | ??:??:?? 31 [NodeInfo] Send owner !167abf61/Stonehenge Washtastic/SHWa
DEBUG | ??:??:?? 31 [NodeInfo] Initial packet id 1615598484
DEBUG | ??:??:?? 31 [NodeInfo] Partially randomized packet id 3285417877
DEBUG | ??:??:?? 31 [NodeInfo] Ignore update from self
ERROR | ??:??:?? 31 [NodeInfo] Error=4, return NAK and drop packet
DEBUG | ??:??:?? 31 [NodeInfo] Partially randomized packet id 663386006
WARN  | ??:??:?? 31 [NodeInfo] Alloc an err=4,to=0x167abf61,idFrom=0xc3d37f95,id=0x278a7796
DEBUG | ??:??:?? 31 [NodeInfo] Enqueued local (id=0x278a7796 fr=0x167abf61 to=0x167abf61, transport = 0, WantAck=0, HopLim=0 Ch=0x0 Portnum=5 requestId=c3d37f95 priority=120)
DEBUG | ??:??:?? 31 [Router] Rx someone rebroadcasting for us (id=0x278a7796 fr=0x167abf61 to=0x167abf61, transport = 0, WantAck=0, HopLim=0 Ch=0x0 Portnum=5 requestId=c3d37f95 priority=1
DEBUG | ??:??:?? 31 [Router] Didn't find pending packet
INFO  | ??:??:?? 31 [Router] Packet History - insert: Using new slot @uptime 31.950s TRACE NEW
DEBUG | ??:??:?? 31 [Router] handleReceived(REMOTE) (id=0x278a7796 fr=0x167abf61 to=0x167abf61, transport = 0, WantAck=0, HopLim=0 Ch=0x0 Portnum=5 requestId=c3d37f95 priority=120)
DEBUG | ??:??:?? 31 [Router] Module 'routing' wantsPacket=1
INFO  | ??:??:?? 31 [Router] Received routing from=0x167abf61, id=0x278a7796, portnum=5, payloadlen=2
DEBUG | ??:??:?? 31 [Router] Routing sniffing (id=0x278a7796 fr=0x167abf61 to=0x167abf61, transport = 0, WantAck=0, HopLim=0 Ch=0x0 Portnum=5 requestId=c3d37f95 priority=120)
DEBUG | ??:??:?? 31 [Router] Received a NAK for 0x0, stopping retransmissions
DEBUG | ??:??:?? 31 [Router] Delivering rx packet (id=0x278a7796 fr=0x167abf61 to=0x167abf61, transport = 0, WantAck=0, HopLim=0 Ch=0x0 Portnum=5 requestId=c3d37f95 priority=120)
DEBUG | ??:??:?? 31 [Router] Ignore update from self
DEBUG | ??:??:?? 31 [Router] Forwarding to phone (id=0x278a7796 fr=0x167abf61 to=0x167abf61, transport = 0, WantAck=0, HopLim=0 Ch=0x0 Portnum=5 requestId=c3d37f95 priority=120)
DEBUG | ??:??:?? 31 [Router] Module 'routing' considered