Installing and Configuring firewalld on RHEL 10
Overview
firewalld is the default dynamic firewall management service used on Red Hat Enterprise Linux (RHEL). It provides a flexible interface for managing Linux firewall rules through zones, services, ports, rich rules, and direct rules.
This document explains how to install, enable, and configure firewalld on a RHEL 10 system.
Prerequisites
Before beginning, ensure:
- You have root or sudo privileges.
- The system is running RHEL 10.
- The system has access to configured package repositories.
Verify the operating system version:
cat /etc/redhat-release
1. Install firewalld
Check whether firewalld is already installed:
rpm -q firewalld
If it is not installed, install it using DNF:
sudo dnf install -y firewalld
Verify the installation:
firewall-cmd --version
2. Enable and Start the Service
Enable firewalld to start automatically during boot:
sudo systemctl enable firewalld
Start the service:
sudo systemctl start firewalld
Verify the service status:
sudo systemctl status firewalld
A healthy service should display a status of:
active (running)
3. Verify Firewall Status
Check whether firewalld is running:
sudo firewall-cmd --state
Expected output:
running
Display current firewall settings:
sudo firewall-cmd --list-all
4. Understanding Zones
Zones define the trust level assigned to network connections.
Display all available zones:
sudo firewall-cmd --get-zones
Display the active zone:
sudo firewall-cmd --get-active-zones
Show the default zone:
sudo firewall-cmd --get-default-zone
Typical zones include:
| Zone | Purpose |
|---|---|
| public | Default for untrusted networks |
| home | Trusted home network |
| work | Trusted work environment |
| internal | Internal organizational network |
| trusted | All traffic accepted |
| drop | All incoming traffic dropped |
| block | Incoming traffic rejected |
5. Change the Default Zone
To set the default zone to public:
sudo firewall-cmd --set-default-zone=public
Verify the change:
sudo firewall-cmd --get-default-zone
6. Allow Network Services
Open common services using predefined service definitions.
Allow SSH
sudo firewall-cmd --permanent --add-service=ssh
Allow HTTP
sudo firewall-cmd --permanent --add-service=http
Allow HTTPS
sudo firewall-cmd --permanent --add-service=https
Apply changes:
sudo firewall-cmd --reload
Verify:
sudo firewall-cmd --list-services
7. Open Specific Ports
To allow TCP port 8080:
sudo firewall-cmd --permanent --add-port=8080/tcp
To allow UDP port 514:
sudo firewall-cmd --permanent --add-port=514/udp
Reload configuration:
sudo firewall-cmd --reload
Verify open ports:
sudo firewall-cmd --list-ports
8. Remove Services or Ports
Remove HTTP access:
sudo firewall-cmd --permanent --remove-service=http
Remove TCP port 8080:
sudo firewall-cmd --permanent --remove-port=8080/tcp
Reload configuration:
sudo firewall-cmd --reload
9. Configure Source-Based Rules
Allow a specific subnet in the internal zone:
sudo firewall-cmd \
--permanent \
--zone=internal \
--add-source=192.168.10.0/24
Reload:
sudo firewall-cmd --reload
View zone details:
sudo firewall-cmd --zone=internal --list-all
10. Configure Rich Rules
Rich rules provide more granular control.
Example: Allow SSH only from a management workstation.
sudo firewall-cmd \
--permanent \
--add-rich-rule='rule family="ipv4" source address="192.168.10.50" service name="ssh" accept'
Reload configuration:
sudo firewall-cmd --reload
Display rich rules:
sudo firewall-cmd --list-rich-rules
11. Runtime vs Permanent Configuration
firewalld supports two configuration types.
| Type | Description |
|---|---|
| Runtime | Active until reboot |
| Permanent | Saved across reboots |
Example runtime change:
sudo firewall-cmd --add-service=http
Example permanent change:
sudo firewall-cmd --permanent --add-service=http
sudo firewall-cmd --reload
12. Reload or Restart firewalld
Reload rules without disrupting existing connections:
sudo firewall-cmd --reload
Restart the service:
sudo systemctl restart firewalld
13. Troubleshooting
Verify service status:
sudo systemctl status firewalld
View logs:
sudo journalctl -u firewalld
Check currently active configuration:
sudo firewall-cmd --list-all
Validate a zone configuration:
sudo firewall-cmd --zone=public --list-all
Common Administrative Commands
# Display active zones
firewall-cmd --get-active-zones
# Display default zone
firewall-cmd --get-default-zone
# List open services
firewall-cmd --list-services
# List open ports
firewall-cmd --list-ports
# Reload configuration
firewall-cmd --reload
# Show all settings
firewall-cmd --list-all
Security Best Practices
- Open only the services and ports required by the application.
- Use service definitions instead of individual ports whenever possible.
- Use rich rules to restrict administrative access.
- Regularly review firewall configuration.
- Use permanent rules for production environments.
- Test rule changes before deployment.
- Maintain SSH access while making firewall modifications.
Conclusion
firewalld provides a flexible and dynamic firewall management framework for RHEL 10. By using zones, services, ports, and rich rules, administrators can build secure and maintainable host-based firewall configurations while minimizing operational complexity.