Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- Connecting to /dev/ttyUSB0, speed 115200
- Escape character: Ctrl-\ (ASCII 28, FS): enabled
- Type the escape character followed by C to get back,
- or followed by ? to see other options.
- ----------------------------------------------------
- GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
- TE: 82252
- BL2 Built : 14:02:06, Apr 18 2017.
- gxl gb6cb79d - xiaobo.gu@droid05
- set vcck to 1120 mv
- set vddee to 1000 mv
- Board ID = 6
- CPU clk: 1200MHz
- DQS-corr enabled
- DDR scramble enabled
- DDR3 chl: Rank0+1 @ 768MHz - PASS
- Rank0: 1024MB(auto)-2T-11
- Rank1: 1024MB(auto)-2T-11
- DataBus test pass!
- AddrBus test pass!
- -s
- Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
- New fip structure!
- Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
- Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x0001b400
- Load bl33 from eMMC, src: 0x0003c200, des: 0x01000000, size: 0x000b4200
- NOTICE: BL3-1: v1.0(debug):866a5ea
- NOTICE: BL3-1: Built : 15:50:05, Feb 28 2017
- [BL31]: GXL CPU setup!
- aml log : bl31 detect secure boot !
- mpu_config_enable:ok
- [Image: gxl_v1.1.3198-b7f9835 2017-04-17 16:15:21 yun.cai@droid06]
- OPS=0x82
- 64 61 d7 75 8c eb 82 57 c1 92 72 7f [0.344568 Inits done]
- secure task start!
- high task start!
- low task start!
- INFO: BL3-1: Initializing runtime services
- WARNING: No OPTEE provided by BL2 boot loader
- ERROR: Error initializing runtime service opteed_fast
- INFO: BL3-1: Preparing for EL3 exit to normal world
- INFO: BL3-1: Next image address = 0x1000000
- INFO: BL3-1: Next image spsr = 0x3c9
- U-Boot 2015.01-g633383b (Jun 12 2017 - 19:10:18)
- DRAM: 2 GiB
- Relocation Offset is: 76ebd000
- register usb cfg[0][1] = 0000000077f5cc10
- [CANVAS]canvas init
- vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
- vpu: clk_level = 7
- vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
- vpu: vpu_clk_gate_init_off
- vpp: vpp_init
- boot_device_flag : 1
- Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
- init bus_cycle=6, bus_timing=7, system=5.0ns
- reset failed
- get_chip_type and ret:fffffffe
- get_chip_type and ret:fffffffe
- chip detect failed and ret:fffffffe
- nandphy_init failed and ret=0xfffffff1
- MMC: aml_priv->desc_buf = 0x0000000073ebd6b0
- aml_priv->desc_buf = 0x0000000073ebf9e0
- SDIO Port B: 0, SDIO Port C: 1
- emmc/sd response timeout, cmd8, status=0x1ff2800
- emmc/sd response timeout, cmd55, status=0x1ff2800
- init_part() 293: PART_TYPE_AML
- [mmc_init] mmc init success
- dtb magic edfe0dd0
- start dts,buffer=0000000073ec2220,dt_addr=0000000073ec2220
- parts: 10
- 00: logo 0000000002000000 1
- 01: recovery 0000000002000000 1
- 02: rsv 0000000000800000 1
- 03: tee 0000000000800000 1
- 04: crypt 0000000002000000 1
- 05: misc 0000000002000000 1
- 06: boot 0000000002000000 1
- 07: system 0000000080000000 1
- 08: cache 0000000020000000 2
- 09: data ffffffffffffffff 4
- init_part() 293: PART_TYPE_AML
- eMMC/TSD partition table have been checked OK!
- check pattern success
- mmc env offset: 0x27400000
- In: serial
- Out: serial
- Err: serial
- reboot_mode=cold_boot
- Unknown command 'cvbs' - try 'help'
- hpd_state=0
- set hdmitx VIC = 16
- config HPLL = 2970000
- HPLL: 0xc000027b
- config HPLL done
- j = 4 vid_clk_div = 1
- hdmitx phy setting done
- hdmitx: set enc for VIC: 16
- rx version is 1.4 or below div=10
- hdmtix: set audio
- [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
- _verify_dtb_checksum()-917: calc 53c81f91, store 53c81f91
- _verify_dtb_checksum()-917: calc 53c81f91, store 53c81f91
- dtb_read()-1039: total valid 2
- dtb_read()-1106: do nothing
- Net: dwmac.c9410000amlkey_init() enter!
- [EFUSE_MSG]keynum is 4
- [BL31]: tee size: 0
- Start read misc partition datas!
- info->attemp_times = 0
- info->active_slot = 0
- info->slot_info[0].bootable = 1
- info->slot_info[0].online = 1
- info->slot_info[1].bootable = 0
- info->slot_info[1].online = 0
- info->attemp_times = 0
- attemp_times = 0
- active slot = 0
- wipe_data=successful
- wipe_cache=successful
- upgrade_step=0
- [OSD]load fb addr from dts
- [OSD]fb_addr for logo: 0x7f851000
- [OSD]load fb addr from dts
- [OSD]fb_addr for logo: 0x7f851000
- [CANVAS]addr=0x7f851000 width=3840, height=2160
- amlkey_init() enter!
- amlkey_init() 71: already init!
- [EFUSE_MSG]keynum is 4
- [BL31]: tee size: 0
- [KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
- [KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet
- [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
- gpio: pin GPIOAO_2 (gpio 102) value is 1
- Product checking: pass!
- Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
- (Re)start USB...
- USB0: USB3.0 XHCI init start
- Register 2000140 NbrPorts 2
- Starting the controller
- USB XHCI 1.00
- scanning bus 0 for devices... 2 USB Device(s) found
- scanning usb for storage devices... 0 Storage Device(s) found
- ** Bad device usb 0 **
- ** Bad device usb 1 **
- ** Bad device usb 2 **
- ** Bad device usb 3 **
- card in
- init_part() 278: PART_TYPE_DOS
- [mmc_init] mmc init success
- Device: SDIO Port B
- Manufacturer ID: 1b
- OEM: 534d
- Name: 00000
- Tran Speed: 50000000
- Rd Block Len: 512
- SD version 3.0
- High Capacity: Yes
- Capacity: 14.9 GiB
- mmc clock: 50000000
- Bus Width: 4-bit
- reading s905_autoscript
- 668 bytes read in 3 ms (216.8 KiB/s)
- ## Executing script at 01020000
- Device: SDIO Port B
- Manufacturer ID: 1b
- OEM: 534d
- Name: 00000
- Tran Speed: 50000000
- Rd Block Len: 512
- SD version 3.0
- High Capacity: Yes
- Capacity: 14.9 GiB
- mmc clock: 50000000
- Bus Width: 4-bit
- reading kernel.img
- 7684096 bytes read in 336 ms (21.8 MiB/s)
- reading dtb.img
- 40977 bytes read in 5 ms (7.8 MiB/s)
- sd dtb.img loaded
- ee_gate_off ...
- ## Booting Android Image at 0x01080000 ...
- reloc_addr =73f423d0
- copy done
- load dtb from 0x1000000 ......
- Uncompressing Kernel Image ... OK
- kernel loaded at 0x01080000, end = 0x01b91180
- Loading Ramdisk to 73cb5000, end 73eaab57 ... OK
- Loading Device Tree to 000000001fff2000, end 000000001ffff010 ... OK
- fdt_instaboot: no instaboot image
- Starting kernel ...
- uboot time: 5274987 us
- [ 0.000000@0] Initializing cgroup subsys cpuset
- [ 0.000000@0] Initializing cgroup subsys cpu
- [ 0.000000@0] Initializing cgroup subsys cpuacct
- [ 0.000000@0] Linux version 3.14.29 (kszaq@FPGAWorker) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP Wed Jul 19 22:15:01 CEST 2017
- [ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
- [ 0.000000@0] no prop version_code
- [ 0.000000@0] bootconsole [earlycon0] enabled
- [ 0.000000@0] fdt Reserved memory table:
- [ 0.000000@0] linux,meson-fb: 0x000000007d100000 - 0x000000007f100000 (32 MiB)
- [ 0.000000@0] linux,di: 0x000000007b300000 - 0x000000007d100000 (30 MiB)
- [ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007b300000, size 30 MiB
- [ 0.000000@0] linux,ion-dev: 0x0000000078300000 - 0x000000007b300000 (48 MiB)
- [ 0.000000@0] linux,vdin1_cma: 0x0000000077000000 - 0x0000000078000000 (16 MiB)
- [ 0.000000@0] cma: Reserved 16 MiB at 77000000, total cma pages:4096
- [ 0.000000@0] linux,ppmgr: 0x0000000078300000 - 0x0000000078300000 (0 MiB)
- [ 0.000000@0] linux,codec_mm_cma: 0x0000000067c00000 - 0x0000000073c00000 (192 MiB)
- [ 0.000000@0] cma: Reserved 192 MiB at 67c00000, total cma pages:53248
- [ 0.000000@0] linux,picdec: 0x0000000078300000 - 0x0000000078300000 (0 MiB)
- [ 0.000000@0] Reserved memory: incorrect alignment of CMA region
- [ 0.000000@0] linux,codec_mm_reserved: 0x0000000063b00000 - 0x0000000067c00000 (65 MiB)
- [ 0.000000@0] fdt Reserved memory total: 386 MiB
- [ 0.000000@0] cma: Reserved 12 MiB at 76400000, total cma pages:56320
- [ 0.000000@0] psci: probing function IDs from device-tree
- [ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc07829f000 s17152 r8192 d23808 u49152
- [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 500232
- [ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=4 vout=1080p60hz,enable hdmimode=1080p60hz cvbsmode= hdmitx= cvbsdrv= androidboot.firstboot=0 jtag=disable androidboot.hardware=amlogic androidboot.slot_suffix=_a bootfromsd console=tty0 systemd.show_status=auto noswap
- [ 0.000000@0] logo: osd1
- [ 0.000000@0] logo: loaded
- [ 0.000000@0] logo: 0x3d800000
- [ 0.000000@0] logo: 1080p60hz
- [ 0.000000@0] vout_serve: 1080p60hz
- [ 0.000000@0] vout_serve: en: 1
- [ 0.000000@0] vout_serve: set_vout_init_vmode: 1080p60hz
- [ 0.000000@0] vout_serve: 1080p60hz
- [ 0.000000@0] vout_serve: enable: 1
- [ 0.000000@0] logo: get hdmimode: 1080p60hz
- [ 0.000000@0] logo: get cvbsmode:
- [ 0.000000@0] tv_vout: cvbs performance line =
- [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
- [ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
- [ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
- [ 0.000000@0] Memory: 1606280K/2044928K available (6949K kernel code, 816K rwdata, 2648K rodata, 908K init, 2922K bss, 438648K reserved)
- [ 0.000000@0] Virtual kernel memory layout:
- [ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
- [ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff8042b0d800 ( 42 MB)
- [ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
- [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07d100000 ( 2001 MB)
- [ 0.000000@0] .init : 0xffffffc0019e1000 - 0xffffffc001ac4300 ( 909 kB)
- [ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc0019e0684 ( 9602 kB)
- [ 0.000000@0] .data : 0xffffffc001ac5000 - 0xffffffc001b91180 ( 817 kB)
- [ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x019dffff]
- [ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=4, Nodes=1
- [ 0.000000@0] arch_multi_cluster:0
- [ 0.000000@0] Hierarchical RCU implementation.
- [ 0.000000@0] RCU debugfs-based tracing is enabled.
- [ 0.000000@0] CONFIG_RCU_FANOUT set to non-default value of 32
- [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
- [ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
- [ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
- [ 0.008245@0] meson_bc_timer: mclk->mux_reg =ffffff800000c990,mclk->reg =ffffff800000e994
- [ 0.016749@0] Console: colour dummy device 80x25
- [ 0.021087@0] console [tty0] enabled
- [ 0.024672@0] bootconsole [earlycon0] disabled
- domain-0 init dvfs: 4
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement