Octa - Meminfo - Before

U-Boot 2012.07-00004-g091558c-dirty (Jun 26 2014 - 09:14:04) for ARNDALE OCTA

CPU: Exynos5420 Rev2.0 [Samsung SOC on SMP Platform Base on ARM CortexA15]
APLL = 800MHz, KPLL = 600MHz
MPLL = 532MHz, BPLL = 800MHz

Board: ARNDALE OCTA
trb: gd->bd = 9f764f88
base[0] = 20000000, size[0] = 10000000
base[1] = 30000000, size[1] = 10000000
base[2] = 40000000, size[2] = 10000000
base[3] = 50000000, size[3] = 10000000
base[4] = 60000000, size[4] = 10000000
base[5] = 70000000, size[5] = 10000000
base[6] = 80000000, size[6] = 10000000
base[7] = 90000000, size[7] = fa00000
base[8] = 5e3d6673, size[8] = 6f733a4a
base[9] = 44435e3d, size[9] = 3d73743a
base[10] = 335c5d5e, size[10] = 753a3334
base[11] = 435e3d65, size[11] = 753a735c
DRAM:  2 GiB
WARNING: Caches not enabled

TrustZone Enabled BSP
BL1 version:

Checking Boot Mode ... SDMMC
MMC:   S5P_MSHC2: 0, S5P_MSHC0: 1
MMC Device 0: 3.7 GiB
MMC Device 1: 3.6 GiB
MMC Device 2: MMC Device 2 not found
there are pending interrupts 0x00000001
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
(Re)start USB...
USB:   Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... The request port(2) is not configured
The request port(2) is not configured
3 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
       scanning usb for ethernet devices... 1 Ethernet Device(s) found
Hit any key to stop autoboot:  0
Downloading from microSD card
reading uImage

2801096 bytes read
reading exynos5420-arndale-octa.dtb

29760 bytes read
reading uInitrd

1765599 bytes read
## Booting kernel from Legacy Image at 20007000 ...
   Image Name:   Linux-3.15.0-rc1-00027-g1c8c3cf-
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2801032 Bytes = 2.7 MiB
   Load Address: 20008000
   Entry Point:  20008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 22000000 ...
   Image Name:   initramfs
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    1765535 Bytes = 1.7 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 21f00000
   Booting using the fdt blob at 0x21f00000
   Loading Kernel Image ... OK
OK
   Loading Ramdisk to 2fe50000, end 2ffff09f ... OK
   Loading Device Tree to 2fe45000, end 2fe4f43f ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.15.0-rc1-00027-g1c8c3cf-dirty (tushar@linaro) (gcc version 4.8.2 20130805 (prerelease) (crosstool-NG linaro-1.13.1-4.8-2013.08 - Linaro GCC
2013.08) ) #109 SMP PREEMPT Thu Jun 26 09:37:48 IST 2014
[    0.000000] CPU: ARMv7 Processor [412fc0f3] revision 3 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] memory scan node memory, reg size 96, data: 20 10 30 10,
[    0.000000] trb: meminfo.nr_banks = 0
[    0.000000] trb: meminfo.nr_banks = 1
[    0.000000] trb: meminfo.nr_banks = 2
[    0.000000] trb: meminfo.nr_banks = 3
[    0.000000] trb: meminfo.nr_banks = 4
[    0.000000] trb: meminfo.nr_banks = 5
[    0.000000] trb: meminfo.nr_banks = 6
[    0.000000] trb: meminfo.nr_banks = 7
[    0.000000] trb: meminfo.nr_banks = 8
[    0.000000] NR_BANKS too low, ignoring memory at 0x5e3d6673
[    0.000000] trb: meminfo.nr_banks = 8
[    0.000000] NR_BANKS too low, ignoring memory at 0x44435e3d
[    0.000000] trb: meminfo.nr_banks = 8
[    0.000000] NR_BANKS too low, ignoring memory at 0x335c5d5e
[    0.000000] trb: meminfo.nr_banks = 8
[    0.000000] NR_BANKS too low, ignoring memory at 0x435e3d65