Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
- TE: 83225
- BL2 Built : 16:32:58, Nov 3 2017.
- gxl gb5491d8 - xiaobo.gu@droid12
- set vdd cpu_a to 1120 mv
- set vdd cpu_b to 1050 mv
- set vddee to 1000 mv
- Board ID = 6
- CPU clk: 1200MHz
- DQS-corr enabled
- DDR scramble enabled
- DDR4 chl: Rank0+1 @ 1008MHz
- Rank0: 2048MB(auto)-2T-18
- Rank1: 1024MB(auto)-2T-18
- DataBus test pass!
- AddrBus test pass!
- -s
- Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
- New fip structure!
- Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
- Load bl31 from eMMC, src: 0x00020200, des: 0x05100000, size: 0x0002c600
- Load bl33 from eMMC, src: 0x00050200, des: 0x01000000, size: 0x00056000
- NOTICE: BL3-1: v1.0(release):35dd647
- NOTICE: BL3-1: Built : 15:20:30, Feb 7 2018
- NOTICE: BL31: BL33 decompress pass
- mpu_config_enable:ok
- [Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07]
- OPS=0x82
- wdt: reset registers!
- f7 1b ea 24 c8 e0 e2 3 6d 6c 4e b5 [0.296722 Inits done]
- secure task start!
- high task start!
- low task start!
- ERROR: Error initializing runtime service opteed_fast
- U-Boot 2015.01-g4c6694f (May 17 2019 - 18:11:25)
- DRAM: 3 GiB
- Relocation Offset is: b6ed0000
- register usb cfg[0][1] = 00000000b7f58538
- [CANVAS]canvas init
- MMC: aml_priv->desc_buf = 0x00000000b3ed0640
- aml_priv->desc_buf = 0x00000000b3ed2960
- SDIO Port B: 0, SDIO Port C: 1
- emmc/sd response timeout, cmd8, status=0x3ff2800
- emmc/sd response timeout, cmd55, status=0x3ff2800
- init_part() 293: PART_TYPE_AML
- [mmc_init] mmc init success
- dtb magic edfe0dd0
- start dts,buffer=00000000b3ed51b0,dt_addr=00000000b3ed51b0
- parts: 10
- 00: logo 0000000002000000 1
- 01: recovery 0000000002000000 1
- 02: rsv 0000000000800000 1
- 03: tee 0000000000800000 1
- 04: crypt 0000000002000000 1
- 05: misc 0000000002000000 1
- 06: boot 0000000002000000 1
- 07: system 0000000080000000 1
- 08: cache 0000000020000000 2
- 09: data ffffffffffffffff 4
- init_part() 293: PART_TYPE_AML
- eMMC/TSD partition table have been checked OK!
- check pattern success
- mmc env offset: 0x27400000
- In: serial
- Out: serial
- Err: serial
- reboot_mode=normal
- [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
- _verify_dtb_checksum()-917: calc 3d4c9206, store 3d4c9206
- _verify_dtb_checksum()-917: calc 3d4c9206, store 3d4c9206
- dtb_read()-1039: total valid 2
- dtb_read()-1106: do nothing
- vpu: clk_level in dts: 7
- vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
- vpu: vpu_clk_gate_init_off
- vpp: vpp_init
- hpd_state=1
- [2160p60hz] is invalid for cvbs.
- set hdmitx VIC = 97
- config HPLL = 5940000
- HPLL: 0xc000027b
- config HPLL done
- j = 9 vid_clk_div = 1
- hdmitx: set enc for VIC: 353
- HDMITX-DWC addr=0x10004006 rd_data=0x40
- Error: HDMITX-DWC exp_data=0xff mask=0x9f
- rx version is 1.4 or below div=10
- hdmtix: set audio
- hdmitx phy setting done
- vpp: vpp_pq_load pq val error !!!
- [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
- dtb_read_shortcut()-975: short cut in...
- Net: dwmac.c9410000amlkey_init() enter!
- [EFUSE_MSG]keynum is 4
- [BL31]: tee size: 0
- Start read misc partition datas!
- info->attemp_times = 0
- info->active_slot = 0
- info->slot_info[0].bootable = 1
- info->slot_info[0].online = 1
- info->slot_info[1].bootable = 0
- info->slot_info[1].online = 0
- info->attemp_times = 0
- attemp_times = 0
- active slot = 0
- wipe_data=successful
- wipe_cache=successful
- upgrade_step=2
- [OSD]load fb addr from dts
- [OSD]fb_addr for logo: 0xbf851000
- [OSD]load fb addr from dts
- [OSD]fb_addr for logo: 0xbf851000
- [CANVAS]addr=0xbf851000 width=3840, height=2160
- amlkey_init() enter!
- amlkey_init() 71: already init!
- [EFUSE_MSG]keynum is 4
- [BL31]: tee size: 0
- [BL31]: tee size: 0
- usid: 98aafc6047d5
- [BL31]: tee size: 0
- mac address: 98:aa:fc:60:47:d5
- [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
- saradc - saradc sub-system
- Usage:
- saradc saradc open <channel> - open a SARADC channel
- saradc close - close the SARADC
- saradc getval - get the value in current channel
- saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
- gpio: pin GPIOAO_2 (gpio 102) value is 1
- saradc: 0x1ca, hw_ver: 0x12
- Product checking: pass! Hardware version: VIM2.V12
- saradc: 0x1c8, hw_ver: 0x12
- saradc: 0x1c9, hw_ver: 0x12
- normal power on
- boot wol: disable
- card out
- emmc/sd response timeout, cmd8, status=0x1ff2800
- emmc/sd response timeout, cmd55, status=0x1ff2800
- emmc/sd response timeout, cmd1, status=0x1ff2800
- SF: Detected W25Q16FW with page size 256, total 2 MiB
- Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
- emmc/sd response timeout, cmd8, status=0x1ff2800
- emmc/sd response timeout, cmd55, status=0x1ff2800
- emmc/sd response timeout, cmd1, status=0x1ff2800
- (Re)start USB...
- USB0: USB3.0 XHCI init start
- Register 3000140 NbrPorts 3
- Starting the controller
- USB XHCI 1.00
- scanning bus 0 for devices... 4 USB Device(s) found
- scanning usb for storage devices... init_part() 278: PART_TYPE_DOS
- 1 Storage Device(s) found
- reading s905_autoscript
- ** Unable to read file s905_autoscript **
- ** Bad device usb 1 **
- ** Bad device usb 2 **
- ** Bad device usb 3 **
- Failed to mount ext2 filesystem...
- ** Unrecognized filesystem type **
- ** Bad device usb 1 **
- ** Bad device usb 2 **
- ** Bad device usb 3 **
- ** Unrecognized filesystem type **
- Failed to mount ext2 filesystem...
- ** Unrecognized filesystem type **
- ee_gate_off ...
- ## Booting Android Image at 0x01080000 ...
- reloc_addr =b3f55360
- copy done
- Kernel command line: buildvariant=userdebug
- load dtb from 0x1000000 ......
- Uncompressing Kernel Image ... OK
- kernel loaded at 0x01080000, end = 0x021e62b0
- Loading Ramdisk to b3d4e000, end b3ebe08c ... OK
- Loading Device Tree to 000000001fff1000, end 000000001ffff5e6 ... OK
- fdt_instaboot: no instaboot image
- Starting kernel ...
- uboot time: 7358634 us
- [ 0.000000@0] Initializing cgroup subsys cpu
- [ 0.000000@0] Initializing cgroup subsys cpuacct
- [ 0.000000@0] Linux version 3.14.29-g069ad3a8 (terry@Server) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #7 SMP P
- REEMPT Fri May 17 18:44:56 CST 2019
- [ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
- [ 0.000000@0] no prop version_code
- [ 0.000000@0] bootconsole [earlycon0] enabled
- [ 0.000000@0] fdt Reserved memory table:
- [ 0.000000@0] linux,di: 0x00000000b6200000 - 0x00000000b8000000 (30 MiB)
- [ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x00000000b6200000, size 30 MiB
- [ 0.000000@0] linux,ion-dev: 0x00000000afd4e000 - 0x00000000b3d4e000 (64 MiB)
- [ 0.000000@0] linux,vdin1_cma: 0x00000000b5000000 - 0x00000000b6000000 (16 MiB)
- [ 0.000000@0] cma: Reserved 16 MiB at b5000000, total cma pages:4096
- [ 0.000000@0] linux,ppmgr: 0x00000000b6200000 - 0x00000000b6200000 (0 MiB)
- [ 0.000000@0] linux,codec_mm_cma: 0x00000000a3c00000 - 0x00000000afc00000 (192 MiB)
- [ 0.000000@0] cma: Reserved 192 MiB at a3c00000, total cma pages:53248
- [ 0.000000@0] linux,picdec: 0x00000000b6200000 - 0x00000000b6200000 (0 MiB)
- [ 0.000000@0] Reserved memory: incorrect alignment of CMA region
- [ 0.000000@0] linux,codec_mm_reserved: 0x000000009fb00000 - 0x00000000a3c00000 (65 MiB)
- [ 0.000000@0] fdt Reserved memory total: 371 MiB
- [ 0.000000@0] cma: Reserved 8 MiB at b4800000, total cma pages:55296
- [ 0.000000@0] psci: Using PSCI v0.1 Function IDs from DT
- [ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc0b615f000 s19968 r8192 d20992 u49152
- [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 742336
- [ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8
- 000 ramoops.console_size=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3d800000,2160p60hz maxcpus=8 vout=2160p60hz,enable hdmimode=2160p60hz cvbsmode=576cvbs hdmitx= ddr_
- size=3 cvbsdrv=0 pq= androidboot.firstboot=0 jtag=disable androidboot.hardware=amlogic androidboot.serialno=98aafc6047d5 mac=98:aa:fc:60:47:d5 androidboot.mac=98:aa:fc:60:47:d5 andr
- oidboot.slot_suffix=_a hwver=VIM2.V12 wol_enable=0 spi_ok buildvariant=userdebug
- [ 0.000000@0] logo: osd1
- [ 0.000000@0] logo: loaded
- [ 0.000000@0] logo: 0x3d800000
- [ 0.000000@0] logo: 2160p60hz
- [ 0.000000@0] vout_serve: 2160p60hz
- [ 0.000000@0] vout_serve: enable: 1
- [ 0.000000@0] logo: get hdmimode: 2160p60hz
- [ 0.000000@0] logo: get cvbsmode: 576cvbs
- [ 0.000000@0] tv_vout: cvbs performance line = 0
- [ 0.000000@0] [amvecm] pq string error !!!
- [ 0.000000@0] jtag: jtag select -1
- [ 0.000000@0] realtek init mac-addr: 98:aa:fc:60:47:d5
- [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
- [ 0.000000@0] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
- [ 0.000000@0] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
- [ 0.000000@0] Memory: 2553556K/3010560K available (11022K kernel code, 1256K rwdata, 4188K rodata, 1343K init, 3796K bss, 457004K reserved)
- [ 0.000000@0] Virtual kernel memory layout:
- [ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff807fff0000 ( 2047 MB)
- [ 0.000000@0] vmemmap : 0xffffff8080000000 - 0xffffff8082840000 ( 40 MB)
- [ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
- [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc0b8000000 ( 2944 MB)
- [ 0.000000@0] .init : 0xffffffc001f5c000 - 0xffffffc0020abe00 ( 1344 kB)
- [ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001f5b814 ( 15215 kB)
- [ 0.000000@0] .data : 0xffffffc0020ac000 - 0xffffffc0021e62b0 ( 1257 kB)
- [ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01f5afff]
- [ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
- [ 0.000000@0] arch_multi_cluster:1
- [ 0.000000@0] Preemptible hierarchical RCU implementation.
- [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
- [ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
- [ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
- [ 0.008246@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
- [ 0.016833@0] Console: colour dummy device 80x25
- [ 0.021096@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
- [ 0.031672@0] pid_max: default: 32768 minimum: 301
- [ 0.036586@0] Security Framework initialized
- [ 0.040786@0] SELinux: Initializing.
- [ 0.044529@0] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
- [ 0.051368@0] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
- [ 0.065494@0] Initializing cgroup subsys debug
- [ 0.065534@0] Initializing cgroup subsys freezer
- [ 0.069054@0] ftrace: allocating 38030 entries in 149 pages
- [ 0.124133@0] /cpus/cpu@0: Missing clock-frequency property
- [ 0.124175@0] /cpus/cpu@1: Missing clock-frequency property
- [ 0.129754@0] /cpus/cpu@2: Missing clock-frequency property
- [ 0.135379@0] /cpus/cpu@3: Missing clock-frequency property
- [ 0.140955@0] /cpus/cpu@100: Missing clock-frequency property
- [ 0.146737@0] /cpus/cpu@101: Missing clock-frequency property
- [ 0.152506@0] /cpus/cpu@102: Missing clock-frequency property
- [ 0.158288@0] /cpus/cpu@103: Missing clock-frequency property
- [ 0.164055@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
- [ 0.214405@0] Meson chip version = RevA (22:A - 82:0)
- [ 0.232778@1] CPU1: Booted secondary processor
- [ 0.252755@2] CPU2: Booted secondary processor
- [ 0.272769@3] CPU3: Booted secondary processor
- [ 0.292790@4] CPU4: Booted secondary processor
- [ 0.312789@5] CPU5: Booted secondary processor
- [ 0.332814@6] CPU6: Booted secondary processor
- [ 0.352827@7] CPU7: Booted secondary processor
- [ 0.352918@0] Brought up 8 CPUs
- [ 0.381737@0] SMP: Total of 8 processors activated.
- [ 0.396830@2] sched: registering cpufreq notifiers for scale-invariant loads
- [ 0.398353@2] instabooting: 0
- [ 0.409935@2] cma: cma_init_reserved_areas, use_cma_first:1
- [ 0.410042@2] pinctrl core: initialized pinctrl subsystem
- [ 0.416048@2] regulator-dummy: no parameters
- [ 0.420562@3] NET: Registered protocol family 16
- [ 0.427286@2] ramoops: using module parameters
- [ 0.429887@2] console [pstore-1] enabled
- [ 0.432702@2] pstore: Registered ramoops as persistent store backend
- [ 0.439104@2] ramoops: attached 0x100000@0x7300000, ecc: 0/0
- [ 0.445811@2] cpuidle: using governor menu
- [ 0.449164@3] aml_vdac_init: module init
- [ 0.453032@2] register canvas platform driver
- [ 0.457293@3] register rdma platform driver
- [ 0.464125@3] vdso: 2 pages (1 code, 1 data) at base ffffffc0020b4000
- [ 0.467971@3] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
- [ 0.475235@3] DMA: preallocated 256 KiB pool for atomic allocations
- [ 0.482141@3] software IO TLB [mem 0x9bc00000-0x9c000000] (4MB) mapped at [ffffffc09bc00000-ffffffc09bffffff]
- [ 0.491153@3] Serial: AMBA PL011 UART driver
- [ 0.496138@3] aml_i2c version: 20140813
- [ 0.499557@2] i2c-core: driver [pmu4] using legacy resume method
- [ 0.505532@2] codec_mm:codec_mm_module_init
- [ 0.509643@2] media_configs_system_init
- [ 0.513563@2] aml_watch_point_probe, in
- [ 0.517730@2] meson_mpll_clk: register mpll_clk_out0 success done
- [ 0.523378@2] meson_mpll_clk: register mpll_clk_out1 success done
- [ 0.529480@2] meson_mpll_clk: register mpll_clk_out2 success done
- [ 0.535817@2] clk_sys: register PLL sys_pll success done
- [ 0.540948@2] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
- [ 0.546318@2] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
- [ 0.551441@2] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
- [ 0.556959@2] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
- [ 0.562902@2] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
- [ 0.568867@2] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
- [ 0.574715@2] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
- [ 0.580582@2] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
- [ 0.586439@2] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
- [ 0.592338@2] gxl_clk: clock initialization complete
- [ 0.597482@2] clkmsr: Gxl msr_clk_reg0=ffffff800003c75c,msr_clk_reg2=ffffff800003e764
- [ 0.607954@2] aml_iomap: amlogic iomap probe done
- [ 0.610458@2] pinmux-gxl c1109880.pinmux: Init pinux probe!
- [ 0.616893@3] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
- [ 0.622836@3] aml-i2c c1108500.i2c: add adapter aml_i2c_adap1(ffffffc09ca190e0)
- [ 0.630549@0] aml-i2c c11087c0.i2c: add adapter aml_i2c_adap2(ffffffc09ca198e0)
- [ 0.637232@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
- [ 0.644919@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
- [ 0.653152@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
- [ 0.661016@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
- domain-0 init dvfs: 4
- domain-1 init dvfs: 4
- [ 0.681548@3] codec_mm has 2 memory regions
- [ 0.681622@3] codec_mm codec_mm.18: assigned reserved memory node linux,codec_mm_cma ok
- [ 0.688245@3] codec_mm codec_mm.18: assigned reserved memory node linux,codec_mm_reserved ok
- [ 0.696856@0] codec_mm has 2 memory regions
- [ 0.700924@0] codec_mm codec_mm.18: assigned reserved memory node linux,codec_mm_cma ok
- [ 0.708989@0] codec_mm codec_mm.18: assigned reserved memory node linux,codec_mm_reserved ok
- [ 0.720072@0] vpu: driver version: v04
- [ 0.721237@0] vpu: load vpu_clk: 666667000Hz(7)
- [ 0.725874@3] vpu: vpu_probe OK
- [ 0.730755@0] tv_vout: tvout_probe
- [ 0.732326@0] tv_vout: chrdev devno 266338304 for disp
- [ 0.737482@0] vout_notify: vout_register_server
- [ 0.742052@0] tv_vout: register tv module server ok
- [ 0.747184@0] tv_vout: create cdev tv
- [ 0.750610@0] tv_vout: tvout_probe OK
- [ 0.755207@3] canvas_probe reg=00000000c8838000,size=400
- [ 0.759659@3] canvas maped reg_base =ffffff800009e000
- [ 0.768942@0] rdma_probe
- [ 1.184426@3] bio: create slab <bio-0> at 0
- [ 1.185612@3] SCSI subsystem initialized
- [ 1.187643@2] usbcore: registered new interface driver usbfs
- [ 1.192785@3] usbcore: registered new interface driver hub
- [ 1.198365@2] usbcore: registered new device driver usb
- [ 1.204421@3] i2c-gpio i2c_gpio.39: using pins 172 (SDA) and 173 (SCL)
- [ 1.210320@2] Linux video capture interface: v2.00
- [ 1.215119@2] pps_core: LinuxPPS API ver. 1 registered
- [ 1.220470@2] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 1.229464@2] PTP clock support registered
- [ 1.234236@2] hdmitx: system: Ver: 2014May6
- [ 1.237862@2] hdmitx: amhdmitx_probe
- [ 1.241623@2] hdmitx: hdmi_init_chip_type: 0
- [ 1.245539@2] hdmitx: system: not find match init-data
- [ 1.250682@2] hdmitx hpd irq = 89
- [ 1.254802@2] hdmitx20: Mapped PHY: 0xc1100000
- [ 1.258504@2] hdmitx20: Mapped PHY: 0xc8834400
- [ 1.262940@2] hdmitx20: Mapped PHY: 0xd0100000
- [ 1.267404@2] hdmitx20: Mapped PHY: 0xc8100000
- [ 1.271863@2] hdmitx20: Mapped PHY: 0xc883c000
- [ 1.276319@2] hdmitx20: Mapped PHY: 0xc1104400
- [ 1.280779@2] hdmitx20: Mapped PHY: 0xc883a000
- [ 1.285350@2] hdmitx20: Mapped PHY: 0xda83a000
- [ 1.289706@2] hdmitx20: Mapped PHY: 0xd0044000
- [ 1.294171@2] hdmitx: alread display in uboot 0x861
- [ 1.299110@2] avmute set to 1
- [ 1.302047@2] hdmitx: attr 420,8bit
- [ 1.306151@2] tv_vout: tv_set_current_vmode[925]fps_target_mode=35
- [ 1.311793@2] tv_vout: mode is 35,sync_duration_den=1,sync_duration_num=60
- [ 1.312917@0] hdmitx: system: irq 2
- [ 1.322183@2] tv_vout: already display in uboot
- [ 1.326716@2] vout_serve: vinfo mode is: 2160p60hz
- [ 1.331528@2] vout_serve: init mode 2160p60hz
- [ 1.336196@2] vout_serve: create_vout_fops OK
- [ 1.340279@2] vout_serve: create vout attribute OK
- [ 1.345090@2] vout_serve: meson_vout_probe OK
- [ 1.349712@2] logo: logo_init
- [ 1.352852@2] osd_rdma: osd_rdma_init: rdma_table p=0xb4841000,op=0xb4841000 , v=0xffffff80000d9000
- [ 1.361585@2] rdma_register, rdma_table_addr ffffff80000db000 rdma_table_addr_phy b4842000 reg_buf ffffffc09babc000
- [ 1.372049@2] rdma_register success, handle 1 table_size 4096
- [ 1.377816@2] osd_rdma: osd_rdma_init:osd reset rdma handle = 1.
- [ 1.383890@2] rdma_register, rdma_table_addr ffffff80000dd000 rdma_table_addr_phy b4843000 reg_buf ffffffc09b86d000
- [ 1.394359@2] rdma_register success, handle 2 table_size 4096
- [ 1.400128@2] osd_rdma: osd_rdma_init:osd rdma handle = 2.
- [ 1.406201@2] Advanced Linux Sound Architecture Driver Initialized.
- [ 1.412639@2] Bluetooth: Core ver 2.18
- [ 1.415852@1] NET: Registered protocol family 31
- [ 1.420343@1] Bluetooth: HCI device and connection manager initialized
- [ 1.426928@1] Bluetooth: HCI socket layer initialized
- [ 1.431982@1] Bluetooth: L2CAP socket layer initialized
- [ 1.437292@1] Bluetooth: SCO socket layer initialized
- [ 1.442311@1] NetLabel: Initializing
- [ 1.445890@1] NetLabel: domain hash size = 128
- [ 1.450451@1] NetLabel: protocols = UNLABELED CIPSOv4
- [ 1.455656@1] NetLabel: unlabeled traffic allowed by default
- [ 1.464462@2] Switched to clocksource arch_sys_counter
- [ 1.508581@2] register gxtv_demod demod driver
- [ 1.509027@1] [amlatvdemod..]aml_atvdemod_init.
- [ 1.512119@1] NET: Registered protocol family 2
- [ 1.517172@1] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
- [ 1.524265@1] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
- [ 1.531377@1] TCP: Hash tables configured (established 32768 bind 32768)
- [ 1.537663@1] TCP: reno registered
- [ 1.540985@1] UDP hash table entries: 2048 (order: 4, 65536 bytes)
- [ 1.547441@1] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
- [ 1.554135@1] NET: Registered protocol family 1
- [ 1.558699@1] RPC: Registered named UNIX socket transport module.
- [ 1.564644@1] RPC: Registered udp transport module.
- [ 1.569414@1] RPC: Registered tcp transport module.
- [ 1.574314@1] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 1.581136@1] pwm: output_co = 16 ; clock_co = 8
- [ 1.585673@1] pwm: npwm= 16
- [ 1.588648@2] pwm: probe ok
- [ 1.591626@2] wifi: power_on_pin_OD = 0;
- [ 1.595212@2] aml_wifi wifi.34: [wifi_dev_probe] no power_on_pin2
- [ 1.601302@2] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm phandle val=3f;pwm-channel1=4;pwm-channel2=12
- [ 1.611338@2] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm_config1[0] = 30541
- [ 1.619035@2] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm_config2[0] = 30518
- [ 1.626735@2] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm_config1[1] = 15270
- [ 1.634429@2] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm_config2[1] = 15259
- [ 1.642134@2] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm_config1[2] = 6
- [ 1.649538@2] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm_config2[2] = 9
- [ 1.656853@2] hdmitx: plugin
- [ 1.664472@0] aml_wifi wifi.34: [pwm_double_channel_conf_dt] wifi pwm dt ok
- [ 1.666734@0] aml_wifi wifi.34: [pwm_double_channel_conf] wifi pwm conf ok
- [ 1.673698@0] aml_wifi wifi.34: [wifi_dev_probe] dhd_static_buf setup
- [ 1.680189@0] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
- [ 1.687726@0] aml_wifi wifi.34: [wifi_dev_probe] interrupt_pin=241
- [ 1.693953@0] aml_wifi wifi.34: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
- [ 1.701375@0] aml_wifi wifi.34: [wifi_dev_probe] power_on_pin=240
- [ 1.707520@0] aml_wifi wifi.34: [wifi_dev_probe] clock_32k_pin=0
- [ 1.713869@0] aml_wifi wifi.34: [wifi_setup_dt] wifi_setup_dt
- [ 1.716528@2] EDID Parser:
- [ 1.716814@2] dump_dtd_info[1966]
- [ 1.716817@2] pixel_clock 8550
- [ 1.716818@2] h_active 1360
- [ 1.716819@2] h_blank 432
- [ 1.716821@2] v_active 768
- [ 1.716822@2] v_blank 27
- [ 1.716823@2] h_sync_offset 64
- [ 1.716825@2] h_sync 112
- [ 1.716826@2] v_sync_offset 3
- [ 1.716827@2] v_sync 6
- [ 1.716830@2] hdmitx: get PMT vic: 4
- [ 1.716833@2] hdmitx: edid: find IEEEOUT
- [ 1.716840@2] hdmitx: update rx hdr info 0 at edid parsing
- [ 1.716883@2] 00ffffffffffff0021573618bde90200251d010380351d7822ee91a3544c9926
- [ 1.716883@2] 0f5054210f00810081408180904095000101a940b300011d007251d01e206e28
- [ 1.716883@2] 55000f484200001e0e1f008051001e30408037000f484200001c000000100000
- [ 1.716883@2] 000000000000000000000000000000fc004d4143524f53494c49434f4e0a0119
- [ 1.716883@2]
- [ 1.716883@2]
- [ 1.716920@2] 020334f152021113841f1003120615071605145e5f636423097f07830100006e
- [ 1.716920@2] 030c001000003c20008001020304e50e61606566662150b051001b3040703600
- [ 1.716920@2] 0f484200001e662156aa51001e30468f33000f484200001e8c0ad08a20e02d10
- [ 1.716920@2] 103e9600100900000018000000000000000000000000000000000000000000b2
- [ 1.716920@2]
- [ 1.716920@2]
- [ 1.716932@2] hdmitx: video: get current mode: 2160p60hz
- [ 1.716933@2] hdmitx: update rx hdr info 0
- [ 1.716936@2] hdmitx: update physcial size: 530 290
- [ 1.716949@2] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 353
- [ 1.716961@2] hdmtix: set audio
- [ 1.716968@2] hdmitx tx_aud_src = 0
- [ 1.716989@2] hdmitx: fs = 0, cd = 4, tmds_clk = 594000
- [ 1.716991@2] hdmitx aud_n_para = 6144
- [ 1.864736@0] aml_wifi wifi.34: [wifi_setup_dt] interrupt_pin(241)
- [ 1.870864@0] aml_wifi wifi.34: [wifi_setup_dt] power_on_pin(240)
- [ 1.877427@2] Unpacking initramfs...
- [ 1.939407@3] Freeing initrd memory: 1472K (ffffffc0b3d4e000 - ffffffc0b3ebe000)
- [ 1.947294@2] futex hash table entries: 2048 (order: 5, 131072 bytes)
- [ 1.948265@2] Initialise system trusted keyring
- [ 1.952774@2] audit: initializing netlink subsys (disabled)
- [ 1.958387@2] audit: type=2000 audit(1.860:1): initialized
- [ 1.964777@2] HugeTLB registered 2 MB page size, pre-allocated 0 pages
- [ 1.978050@2] VFS: Disk quotas dquot_6.5.2
- [ 1.978337@3] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
- [ 1.988448@2] NFS: Registering the id_resolver key type
- [ 1.988530@2] Key type id_resolver registered
- [ 1.992854@2] Key type id_legacy registered
- [ 1.997179@2] NTFS driver 2.1.30 [Flags: R/O].
- [ 2.001956@2] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
- [ 2.009735@2] fuse init (API version 7.22)
- [ 2.013573@2] msgmni has been set to 5422
- [ 2.018593@2] NET: Registered protocol family 38
- [ 2.021565@2] Key type asymmetric registered
- [ 2.025983@2] Asymmetric key parser 'x509' registered
- [ 2.031324@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
- [ 2.038551@2] io scheduler noop registered
- [ 2.042641@2] io scheduler deadline registered
- [ 2.047443@2] io scheduler cfq registered (default)
- [ 2.102500@3] meson-rng c8834000.rng: hwrng registered
- [ 2.107282@2] loop: module loaded
- [ 2.107920@2] zram: Created 1 device(s) ...
- [ 2.109842@2] khadas_fan_probe
- [ 2.112855@3] fanctl fan.13: trigger temperature is level0:50, level1:60, level2:70.
- [ 2.120749@2] mcu_probe
- [ 2.123400@2] create_mcu_attrs
- [ 2.127270@2] mcu_probe,wol enable=0
- [ 2.130013@3] i2c-core: driver [khadas-mcu] using legacy suspend method
- [ 2.136468@3] i2c-core: driver [khadas-mcu] using legacy resume method
- [ 2.143806@3] mtdoops: mtd device (mtddev=name/number) must be supplied
- [ 2.150425@2] tun: Universal TUN/TAP device driver, 1.6
- [ 2.154992@2] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- [ 2.286230@2] libphy: stmmac: probed
- [ 2.286265@2] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
- [ 2.290800@2] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
- [ 2.297302@2] PPP generic driver version 2.4.2
- [ 2.301424@2] PPP BSD Compression module registered
- [ 2.306151@2] PPP Deflate Compression module registered
- [ 2.311382@2] PPP MPPE Compression module registered
- [ 2.316358@2] NET: Registered protocol family 24
- [ 2.321195@3] usbcore: registered new interface driver asix
- [ 2.326814@2] usbcore: registered new interface driver ax88179_178a
- [ 2.333019@2] usbcore: registered new interface driver cdc_ether
- [ 2.339101@3] usbcore: registered new interface driver net1080
- [ 2.344939@3] usbcore: registered new interface driver cdc_subset
- [ 2.351035@2] usbcore: registered new interface driver zaurus
- [ 2.356881@3] usbcore: registered new interface driver cdc_ncm
- [ 2.362911@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 2.369303@2] ehci-h20ahb: H20AHB-EHCI Host Controller driver
- [ 2.375427@2] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 2.381915@2] usbcore: registered new interface driver cdc_acm
- [ 2.387329@2] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
- [ 2.395740@2] usbcore: registered new interface driver usb-storage
- [ 2.402045@2] usbcore: registered new interface driver usbserial
- [ 2.408672@2] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff800011e000
- [ 2.418823@2] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
- [ 2.425328@2] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff800012a080
- [ 2.436743@3] mousedev: PS/2 mouse device common for all mice
- [ 2.442296@2] usbcore: registered new interface driver xpad
- [ 2.456557@3] khadas-hym8563 2-0051: rtc core: registered khadas-hym8563 as rtc0
- [ 2.458634@3] i2c /dev entries driver
- [ 2.462849@3] IR NEC protocol handler initialized
- [ 2.466851@3] IR RC5(x) protocol handler initialized
- [ 2.471802@3] IR RC6 protocol handler initialized
- [ 2.476536@3] IR JVC protocol handler initialized
- [ 2.481251@3] IR Sony protocol handler initialized
- [ 2.486107@3] IR RC5 (streamzap) protocol handler initialized
- [ 2.491839@3] IR SANYO protocol handler initialized
- [ 2.496747@3] IR MCE Keyboard/mouse protocol handler initialized
- [ 2.502980@2] usbcore: registered new interface driver uvcvideo
- [ 2.508777@2] USB Video Class driver (1.1.1)
- [ 2.513168@2] usbcore: registered new interface driver cx231xx
- [ 2.518892@2] cx231xx: Cx231xx dvb Extension initialized
- [ 2.525222@2] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
- [ 2.533013@2] Bluetooth: HCI UART driver ver 2.2
- [ 2.537531@2] Bluetooth: HCI H4 protocol initialized
- [ 2.542893@2] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
- [ 2.550298@0] cpu cpu4: bL_cpufreq_init: CPU 4 initialized
- [ 2.553689@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
- [ 2.561601@0] CPUidle arm64: cpuidle init start!!
- [ 2.566540@0] CPUidle arm64: cpuidle init done!
- [ 2.571182@2] hidraw: raw HID events driver (C) Jiri Kosina
- [ 2.576680@2] @@@@@@@@@@_____2______in dia_init()
- [ 2.580830@2] ATVR driver - init called!
- [ 2.584891@3] usbcore: registered new interface driver usbhid
- [ 2.590539@3] usbhid: USB HID core driver
- [ 2.594991@2] ashmem: initialized
- [ 2.598057@3] logger: created 256K log 'log_main'
- [ 2.602761@3] logger: created 256K log 'log_events'
- [ 2.607704@2] logger: created 256K log 'log_radio'
- [ 2.612468@2] logger: created 256K log 'log_system'
- [ 2.618678@1] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff800012c4c0
- [ 2.624426@1] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
- [ 2.639454@1] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
- [ 2.642083@1] console [ttyS0] enabled
- [ 2.642083@1] console [ttyS0] enabled
- [ 2.649328@1] bootconsole [earlycon0] disabled
- [ 2.649328@1] bootconsole [earlycon0] disabled
- [ 2.658507@0] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff800012e4c0
- [ 2.665177@0] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
- [ 2.674791@0] meson_uart c81004e0.serial: ==uart4 reg addr = ffffff800013a4e0
- [ 2.681516@0] c81004e0.serial: ttyS4 at MMIO 0xc81004e0 (irq = 229, base_baud = 1500000) is a meson_uart
- [ 2.691429@0] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
- [ 2.700851@0] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
- [ 2.708386@0] hdmitx_hdcp_init
- [ 2.711713@0] aml_vrtc rtc.33: rtc core: registered aml_vrtc as rtc1
- [ 2.717561@0] BLASTER Driver Init
- [ 2.721230@0] secmon has 1 memory regions
- [ 2.724716@0] secmon: share in base: 0xffffff800014c000, share out base: 0xffffff800014e000
- [ 2.732905@0] secmon secmon.4: assigned reserved memory node linux,secmon ok
- [ 2.739922@0] secmon: probe done
- [ 2.743438@0] storage: storage in base: 0xffffff8001800000
- [ 2.748545@0] storage: storage out base: 0xffffff8001880000
- [ 2.754029@0] storage: storage block base: 0xffffff8001900000
- [ 2.759770@0] storage: probe done!
- [ 2.763896@0] aml_sd_emmc_probe: line 3608
- [ 2.767212@0] mmc driver version: 1.07, 2017-4-26: Support new emmc host controller for version 3
- [ 2.776703@0] aml_sd_emmc_reg_init 1152
- [ 2.779794@0] get property: ocr_avail, value:0x00200080
- [ 2.786245@0] get property: f_min, value:300000
- [ 2.792368@0] get property: f_max, value:100000000
- [ 2.798719@0] get property: max_req_size, value:0x00020000
- [ 2.805237@0] get property: pinname, str:emmc
- [ 2.810964@0] get property: card_type, value:1
- [ 2.816686@0] get property: gpio_dat3, str:
- [ 2.822118@0] get property: hw_reset, str:
- [ 2.827564@0] emmc:pdata->caps = c0000d47
- [ 2.831486@0] emmc:pdata->caps2 = 18060
- [ 2.835285@0] emmc:pdata->pm_caps = 0
- [ 2.838945@0] storage 1, boot 1
- [ 2.842004@0] get_storage_dev return 1
- [ 2.884479@1] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
- [ 2.884710@1] aml_sd_emmc_probe: line 3608
- [ 2.889323@1] aml_sd_emmc_reg_init 1152
- [ 2.892575@1] get property: ocr_avail, value:0x00200080
- [ 2.899011@1] get property: f_min, value:400000
- [ 2.905122@1] get property: f_max, value:100000000
- [ 2.911497@1] get property: max_req_size, value:0x00020000
- [ 2.917971@1] get property: irq_in, value:3
- [ 2.923658@1] get property: irq_out, value:5
- [ 2.929364@1] get property: gpio_cd, str:
- [ 2.934791@1] get property: pinname, str:sd
- [ 2.940392@1] get property: jtag_pin, str:
- [ 2.945861@1] get property: card_type, value:5
- [ 2.951519@1] get property: card_in_delay, value:400
- [ 2.957428@1] get property: gpio_dat3, str:
- [ 2.962829@1] sd:pdata->caps = 7
- [ 2.966034@1] sd:pdata->caps2 = 0
- [ 2.969077@3] emmc: BKOPS_EN bit is not set
- [ 2.973424@1] sd:pdata->pm_caps = 0
- [ 2.975994@3] emmc: trying cali 0-th time(s)
- [ 2.981031@3] emmc: delay[0]= 4500 padding= 2, bidx=4
- [ 2.981035@3] emmc: delay[1]= 4500 padding= 2, bidx=4
- [ 2.981036@3] emmc: delay[2]= 4500 padding= 2, bidx=4
- [ 2.981038@3] emmc: delay[3]= 4750 padding= 1, bidx=4
- [ 2.981040@3] emmc: delay[4]= 4750 padding= 1, bidx=4
- [ 2.981042@3] emmc: delay[5]= 4750 padding= 1, bidx=4
- [ 2.981044@3] emmc: delay[6]= 4750 padding= 1, bidx=4
- [ 2.981046@3] emmc: delay[7]= 4750 padding= 1, bidx=4
- [ 2.981048@3] emmc: calibration result @ 0: max(4750), min(4500)
- [ 2.981051@3] emmc: line_delay =0x111, max_cal_result =4750
- [ 2.981052@3] emmc: base_index_max 4, base_index_min 4
- [ 2.981062@3] emmc: clk 100000000 SDR mode tuning start
- [ 2.981472@3] emmc: rx_tuning_result[0] = 10
- [ 2.981835@3] emmc: rx_tuning_result[1] = 10
- [ 2.982197@3] emmc: rx_tuning_result[2] = 10
- [ 2.982560@3] emmc: rx_tuning_result[3] = 10
- [ 2.982922@3] emmc: rx_tuning_result[4] = 10
- [ 2.983284@3] emmc: rx_tuning_result[5] = 10
- [ 2.983646@3] emmc: rx_tuning_result[6] = 10
- [ 2.984006@3] emmc: rx_tuning_result[7] = 10
- [ 2.984368@3] emmc: rx_tuning_result[8] = 10
- [ 2.984735@3] emmc: rx_tuning_result[9] = 10
- [ 2.984737@3] emmc: best_win_start =0, best_win_size =10
- [ 2.984740@3] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x2000
- [ 2.984743@3] emmc: gclock =0x100024a, gdelay=0x111, gadjust=0x2000
- [ 2.984898@3] emmc: support driver strength type 1
- [ 2.984967@3] emmc: try set sd/emmc to DDR mode
- [ 2.984971@3] emmc: try set sd/emmc to DDR mode
- [ 2.985105@3] emmc: new HS400 MMC card at address 0001
- [ 2.986127@2] emmc: clock 100000000, 8-bit-bus-width
- [ 2.986127@2]
- [ 2.986127@2] mmcblk0: emmc:0001 BWBD3R 29.1 GiB
- [ 2.986542@2] mmcblk0boot0: emmc:0001 BWBD3R partition 1 4.00 MiB
- [ 2.986962@2] mmcblk0boot1: emmc:0001 BWBD3R partition 2 4.00 MiB
- [ 2.987372@2] mmcblk0rpmb: emmc:0001 BWBD3R partition 3 4.00 MiB
- [ 2.988407@3] mmcblk0: unknown partition table
- [ 2.989169@2] [mmc_read_partition_tbl] mmc read partition OK!
- [ 2.989171@2] add_emmc_partition
- [ 2.989369@3] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
- [ 2.989517@2] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
- [ 2.989647@3] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
- [ 2.989771@2] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
- [ 2.989904@3] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
- [ 2.990040@2] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
- [ 2.990169@3] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
- [ 2.990295@2] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
- [ 2.990428@3] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
- [ 2.990565@2] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
- [ 2.990694@3] [mmcblk0p11] boot offset 0x000034400000, size 0x000002000000
- [ 2.990827@2] [mmcblk0p12] system offset 0x000036c00000, size 0x000080000000
- [ 2.990960@3] [mmcblk0p13] data offset 0x0000b7400000, size 0x000690800000
- [ 2.990989@3] card key: card_blk_probe.
- [ 2.990994@3] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
- [ 2.990996@3] emmc key: emmc_key_init:552 ok.
- [ 2.993366@3] amlmmc_dtb_init: register dtb chardev
- [ 2.993366@3] calc 3d4c9206, store 3d4c9206
- [ 2.995593@3] calc 3d4c9206, store 3d4c9206
- [ 2.995595@3] total valid 2
- [ 2.996046@2] amlmmc_dtb_init: register dtb chardev OK
- [ 2.996046@2] Exit aml_emmc_partition_ops OK.
- [ 2.998293@3] mmcblk0boot1: unknown partition table
- [ 2.999393@3] mmcblk0boot0: unknown partition table
- [ 2.999661@2] clear_emmc_wait_flag
- [ 3.364721@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
- [ 3.364947@3] aml_sd_emmc_probe: line 3608
- [ 3.369482@3] aml_sd_emmc_reg_init 1152
- [ 3.372826@3] get property: ocr_avail, value:0x00200080
- [ 3.379254@3] get property: f_min, value:400000
- [ 3.385361@3] get property: f_max, value:200000000
- [ 3.391743@3] get property: max_req_size, value:0x00020000
- [ 3.398225@3] get property: pinname, str:sdio
- [ 3.403986@3] get property: card_type, value:3
- [ 3.409743@3] sdio:pdata->caps = 78107
- [ 3.413386@3] sdio:pdata->caps2 = 0
- [ 3.416850@3] sdio:pdata->pm_caps = 1
- [ 3.454475@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
- [ 3.455053@3] ion_dev has 1 memory regions
- [ 3.458762@3] ion_dev ion_dev.21: assigned reserved memory node linux,ion-dev ok
- [ 3.479438@2] ion_carveout_heap_create: base 2949963776 size 67108864 align 0
- [ 3.481367@3] fb: osd_init_module
- [ 3.484325@3] fb: viu vsync irq: 35
- [ 3.487666@3] fb: failed to init reserved memory
- [ 3.492218@3] fb: osd_set_free_scale_mode_hw
- [ 3.496461@3] fb: osd_probe vinfo:ffffffc002165e00
- [ 3.501190@3] fb: init fbdev bpp is:32
- [ 3.505432@2] fb: set osd0 reverse as NONE
- [ 3.521795@0] fb: osd probe OK
- [ 3.522054@0] ge2d: ge2d_init_module
- [ 3.522766@0] ge2d: ge2d_dev major:240
- [ 3.526878@2] ge2d: vpu clock is 666660000 HZ
- [ 3.530793@2] ge2d: ge2d clock is 400 MHZ
- [ 3.534767@2] ge2d: ge2d: pdev=ffffffc09ca92800, irq=182, rstc=0xffffffc09ae33a40, clk=ffffffc09ca7c300
- [ 3.544114@2] ge2d: mapped phy: 0xd0160000
- [ 3.548126@2] ge2d: ge2d start monitor
- [ 3.551902@1] ge2d: ge2d workqueue monitor start
- [ 3.552174@0] sysled: module init
- [ 3.552326@0] sysled: init level = 0
- [ 3.552327@0] sysled: led_gpio = 154
- [ 3.552328@0] sysled: active_low = 0
- [ 3.552493@2] sysled: module probed ok
- [ 3.552939@2] pwmled: module init
- [ 3.553317@2] codec:Amlogic A/V streaming port init
- [ 3.555427@2] codec:get gate demux control ok ffffffc09cb37340
- [ 3.555438@2] codec:get gate parser_top control ok ffffffc09ae68000
- [ 3.555444@2] codec:get gate vpu_intr control ok ffffffc09ae68080
- [ 3.555449@2] codec:get gate vdec control ok ffffffc09ae68100
- [ 3.556384@3] codec:[tsync_pcr_init]init success.
- [ 3.556419@3] codec:amvideocap_init_module
- [ 3.556572@3] codec:amvideocap_probe,amvideocap
- [ 3.556575@3] codec:use cma buf.
- [ 3.556576@3] codec:amvideocap_dev_register
- [ 3.557260@2] codec:amvdec_mmpeg4 module init
- [ 3.557628@3] ammvdec_h264 module init
- [ 3.559233@3] amvenc_avc_probe -- reserved memory config fail.
- [ 3.559237@3] amvenc_avc - cma memory pool size: 60 MB
- [ 3.559259@3] encode_wq_init.
- [ 3.559264@3] encode start monitor.
- [ 3.559321@0] encode workqueue monitor start.
- [ 3.559689@2] jpegenc module init
- [ 3.560028@3] codec:picdec_driver_probe called.
- [ 3.560032@3] picdec has 1 memory regions
- [ 3.560065@3] codec:picdec_driver_probe done.
- [ 3.560910@2] codec:vdec_request_irq ffffffc0017b91b4, vsync
- [ 3.561129@3] codec:create_ge2d_work_queue video task ok
- [ 3.683002@2] rdma_register, rdma_table_addr ffffff8000256000 rdma_table_addr_phy b4850000 reg_buf ffffffc09a958000
- [ 3.693209@2] rdma_register success, handle 3 table_size 32768
- [ 3.698991@2] video_rdma:rdma_init video rdma handle = 3.
- [ 3.704320@2] codec:used fix clk for vdec clk source!
- [ 3.709328@2] codec:register clk_set_setting cpu[34]
- [ 3.714724@2] vpu_init
- [ 3.716755@2] vpu_probe
- [ 3.718980@2] HevcEnc reserved memory config fail.
- [ 3.723721@2] HevcEnc - cma memory pool size: 64 MB
- [ 3.728876@2] HevcEnc - wave420l_irq: 219
- [ 3.732558@2] vpu base address get from platform driver physical base addr=0xc8810000, virtual base=0xffffff80003d8000
- [ 3.743423@1] success to probe vpu device with video memory from cma
- [ 3.751120@1] DI: di_module_init ok.
- [ 3.752968@1] DI: di_module_init: major 233
- [ 3.757698@1] DI: di_probe
- [ 3.760282@1] deinterlace has 1 memory regions
- [ 3.764229@1] deinterlace deinterlace.25: assigned reserved memory node linux,di ok
- [ 3.764892@6] [aml_is_card_insert] card OUT
- [ 3.775933@1] DI-di_probe: get flag_cma error.
- [ 3.780328@1] di_irq:78,timerc_irq:38
- [ 3.784173@1] rdma_register, rdma_table_addr ffffff80001b9000 rdma_table_addr_phy b484a000 reg_buf ffffffc09a9e0000
- [ 3.794306@1] rdma_register success, handle 4 table_size 8192
- [ 3.799973@1] DI: di_probe allocate rdma channel 4.
- [ 3.804855@1] DI: DI hw version 2.
- [ 3.808173@1] 0x000000db:Y=db,U=0,V=0
- [ 3.811782@1] 0x000000dc:Y=dc,U=0,V=0
- [ 3.815416@1] 0x000000dd:Y=dd,U=0,V=0
- [ 3.819027@1] 0x000000de:Y=de,U=0,V=0
- [ 3.822651@1] 0x000000df:Y=df,U=0,V=0
- [ 3.826284@1] 0x000000e0:Y=e0,U=0,V=0
- [ 3.829897@1] 0x000000e1:Y=e1,U=0,V=0
- [ 3.833517@1] 0x000000e2:Y=e2,U=0,V=0
- [ 3.837145@1] 0x000000e3:Y=e3,U=0,V=0
- [ 3.840765@1] 0x000000f0:Y=f0,U=0,V=0
- [ 3.844387@1] 0x000000f1:Y=f1,U=0,V=0
- [ 3.848024@1] 0x000000f2:Y=f2,U=0,V=0
- [ 3.851629@1] 0x000000f3:Y=f3,U=0,V=0
- [ 3.855266@1] 0x000000f4:Y=f4,U=0,V=0
- [ 3.858876@1] 0x000000f5:Y=f5,U=0,V=0
- [ 3.862497@1] 0x000000f6:Y=f6,U=0,V=0
- [ 3.866129@1] 0x000000f7:Y=f7,U=0,V=0
- [ 3.869742@1] 0x000000f8:Y=f8,U=0,V=0
- [ 3.873366@1] 0x000000f9:Y=f9,U=0,V=0
- [ 3.876996@1] 0x000000fa:Y=fa,U=0,V=0
- [ 3.880610@1] 0x000000fb:Y=fb,U=0,V=0
- [ 3.884232@1] 0x000000fc:Y=fc,U=0,V=0
- [ 3.887863@1] 0x000000fd:Y=fd,U=0,V=0
- [ 3.891480@1] 0x000000fe:Y=fe,U=0,V=0
- [ 3.895113@1] 0x000000ff:Y=ff,U=0,V=0
- [ 3.898723@1] DI: support multi decoding 253~254~255.
- [ 3.903811@1] DI: di_probe:Di use HRTIMER
- [ 3.908518@1] efusekeynum: 4
- [ 3.910550@1] efusekeyname: mac offset: 0 size: 12
- [ 3.916954@1] efusekeyname: mac_bt offset: 12 size: 12
- [ 3.923307@1] efusekeyname: mac_wifi offset: 24 size: 12
- [ 3.929704@1] efusekeyname: usid offset: 36 size: 12
- [ 3.936390@3] efuse efuse.9: probe OK!
- [ 3.940188@3] key unify config unifykey-num is 14
- [ 3.944498@3] key unify fact unifykey-num is 14
- [ 3.948923@3] aml_unifykeys_probe:1280=============unifykey_devno:e700000
- [ 3.955946@0] 6unifykey: device unifykeys created ok
- [ 3.960820@3] 6aml_unifykeys_init done!
- [ 3.964565@3] PPMGRDRV: warn: ppmgr module init func called
- [ 3.970236@3] PPMGRDRV: err: ppmgr_driver_probe called
- [ 3.975179@3] ppmgr has 1 memory regions
- [ 3.979064@3] PPMGRDRV: info: ppmgr_dev major:230
- [ 3.984632@3] PPMGRDRV: info: ppmgr_probe done
- [ 3.988669@3] amlogic rfkill init
- [ 3.991480@3] enter bt_probe of_node
- [ 3.994923@3] not get gpio_en
- [ 3.997824@3] power on valid level is high
- [ 4.001705@3] bt: power_on_pin_OD = 0;
- [ 4.005997@3] Bluetooth: BlueSleep Mode Driver Ver 1.2
- [ 4.011314@3] ionvideo-000: V4L2 device registered as video13
- [ 4.016544@0] ionvideo-001: V4L2 device registered as video14
- [ 4.022267@3] ionvideo-002: V4L2 device registered as video15
- [ 4.027915@3] ionvideo-003: V4L2 device registered as video16
- [ 4.033581@0] ionvideo-004: V4L2 device registered as video17
- [ 4.039392@3] ionvideo-005: V4L2 device registered as video18
- [ 4.045021@3] ionvideo-006: V4L2 device registered as video19
- [ 4.050666@0] ionvideo-007: V4L2 device registered as video20
- [ 4.056487@3] ionvideo-008: V4L2 device registered as video21
- [ 4.061910@3] ionvid: info: Video Technology Magazine Ion Video
- [ 4.067818@3] ionvid: info: Capture Board ver 1.0 successfully loaded
- [ 4.074162@3] audio_dsp: [dsp]register dsp to char divece(257)
- [ 4.081001@3] amaudio: amaudio: driver amaudio succuess!
- [ 4.085613@3] amlvid:info: amlvideo_init called
- [ 4.089576@0] amlvid:info: amlvideo_create_instance called
- [ 4.095144@0] amlvid:info: v4l2_dev.name=:amlvideo-000
- [ 4.100382@3] amlvideo-000: V4L2 device registered as video10
- [ 4.106350@0] vdin_drv_init: major 229
- [ 4.109975@3] rdma_register, rdma_table_addr ffffff80001bc000 rdma_table_addr_phy b484c000 reg_buf ffffffc09a807a00
- [ 4.119972@3] rdma_register success, handle 5 table_size 512
- [ 4.125567@3] vdin_drv_probe:vdin.0 rdma hanld 5.
- [ 4.130435@3]
- [ 4.130435@3] vdin memory resource undefined!!
- [ 4.136385@3] vdin0 cma_mem_size = 16 MB
- [ 4.140225@3] vdin0 irq: 115 rdma irq: 2
- [ 4.144151@3] vdin_drv_probe: fclk_div5 is 400 MHZ
- [ 4.148882@3] vdin_drv_probe: vdin[0] clock is 50 MHZ
- [ 4.154105@0] vdin_drv_probe: driver initialized ok
- [ 4.158870@0] rdma_register, rdma_table_addr ffffff80001be000 rdma_table_addr_phy b484d000 reg_buf ffffffc09aeeca00
- [ 4.165010@5] [aml_is_card_insert] card OUT
- [ 4.173227@0] rdma_register success, handle 6 table_size 512
- [ 4.178783@0] vdin_drv_probe:vdin.1 rdma hanld 6.
- [ 4.183678@3] vdin1 has 1 memory regions
- [ 4.187372@3] vdin vdin1.27: assigned reserved memory node linux,vdin1_cma ok
- [ 4.194387@3]
- [ 4.194387@3] vdin memory resource done.
- [ 4.200004@3] vdin1 cma_mem_size = 16 MB
- [ 4.203877@3] vdin1 irq: 117 rdma irq: 4
- [ 4.207814@3] vdin_drv_probe: fclk_div5 is 400 MHZ
- [ 4.212506@3] vdin_drv_probe: vdin[1] clock is 50 MHZ
- [ 4.217769@3] vdin_drv_probe: driver initialized ok
- [ 4.222529@0] vdin_drv_init: vdin driver init done
- [ 4.227100@0] tvafe_drv_init: major 228
- [ 4.231278@3] tvafe: tvafe_init.
- [ 4.234438@3] vbi: vbi_init.
- [ 4.237549@3] [RX]-hdmirx: hdmirx_init.
- [ 4.240708@3] ESM HLD: Initializing...
- [ 4.244412@3] ESM HLD: Registering device range 'esm_rx'...
- [ 4.249954@3] ESM HLD: Device range 'esm_rx' has been registered.
- [ 4.255988@3] ESM HLD: Creating class /sys/class/elliptic_rx...
- [ 4.261956@3] ESM HLD: The class /sys/class/elliptic_rx has been created.
- [ 4.268571@3] ESM HLD: Creating device 'esm_rx'...
- [ 4.273464@0] ESM HLD: Device 'esm_rx' has been created.
- [ 4.278613@0] ESM HLD: Done initializing the HLD driver.
- [ 4.283829@0] amvdec_656in module: init.
- [ 4.287726@0] amvdec_656in_init_module. 1 hardware detected!.
- [ 4.293446@0] amvdec_656in_init_module:major 225
- [ 4.298260@3] amvdec_656in_probe:start probe .
- [ 4.302378@3] amvdec_656in_probe: bt656 devp->index =0
- [ 4.307508@3] amvdec_656in_probe: bt656[0] clock is 333 MHZ
- [ 4.313185@3] amvdec_656in_probe:bt656[0]start get ioremap .
- [ 4.318709@3] amvdec_656in_probe: bt656[0] maped reg_base =ffffff80001ca000, size=7c
- [ 4.326358@3] amvdec_656in_probe: tvin_frontend_init done :0
- [ 4.331964@3] amvdec_656in probe ok.
- [ 4.335526@3] amvdec_656in_probe:start probe .
- [ 4.339894@3] amvdec_656in_probe: bt656 devp->index =1
- [ 4.345014@3] amvdec_656in_probe: bt656[1] clock is 333 MHZ
- [ 4.350657@0] amvdec_656in_probe:bt656[1]start get ioremap .
- [ 4.356253@0] amvdec_656in_probe: bt656[1] maped reg_base =ffffff80001cc000, size=7c
- [ 4.363869@0] amvdec_656in_probe: tvin_frontend_init done :1
- [ 4.369492@0] amvdec_656in probe ok.
- [ 4.373260@3] amvdec_656in_init_module: bt656 driver init done
- [ 4.378803@3] [viuin..]viuin_init_module viuin module init
- [ 4.384730@0] [viuin..]viuin_probe probe ok.
- [ 4.388615@3] aml_vecm_init:module init
- [ 4.392406@3]
- [ 4.392406@3] VECM probe start
- [ 4.397334@0] Can't find wb_sel.
- [ 4.400270@0] dolby_vision_init_receiver(dvel)
- [ 4.404683@0] dolby_vision_init_receiver: dvel
- [ 4.409272@0] aml_vecm_probe: ok
- [ 4.413109@0] saradc c1108680.saradc: initialized by BL30
- [ 4.417663@0] saradc c1108680.saradc: calibration start:
- [ 4.423007@0] saradc c1108680.saradc: nominal=0, value=7
- [ 4.428180@0] saradc c1108680.saradc: nominal=256, value=231
- [ 4.433774@0] saradc c1108680.saradc: nominal=512, value=459
- [ 4.439423@0] saradc c1108680.saradc: nominal=768, value=689
- [ 4.445006@0] saradc c1108680.saradc: nominal=1023, value=917
- [ 4.450637@0] saradc c1108680.saradc: calibration end: coef=4578
- [ 4.456921@3] meson-remote: Driver init
- [ 4.460500@3] meson-remote: remote_probe
- [ 4.464294@3] meson-remote c8100580.rc: protocol = 0x1
- [ 4.469467@3] meson-remote c8100580.rc: platform_data irq =228
- [ 4.475166@3] meson-remote c8100580.rc: custom_number = 2
- [ 4.480485@3] meson-remote c8100580.rc: ptable->map_size = 13
- [ 4.486189@3] meson-remote c8100580.rc: ptable->custom_name = khadas-ir
- [ 4.492728@3] meson-remote c8100580.rc: ptable->custom_code = 0xff00
- [ 4.499030@3] meson-remote c8100580.rc: ptable->release_delay = 80
- [ 4.505167@3] meson-remote c8100580.rc: ptable->map_size = 45
- [ 4.510840@3] meson-remote c8100580.rc: ptable->custom_name = dvb-ir
- [ 4.517147@3] meson-remote c8100580.rc: ptable->custom_code = 0xfe01
- [ 4.523432@3] meson-remote c8100580.rc: ptable->release_delay = 80
- [ 4.529563@3] meson-remote c8100580.rc: please config fn_key_scancode_other item
- [ 4.536905@3] meson-remote c8100580.rc: default protocol = 0x1 and id = 0
- [ 4.543615@3] meson-remote c8100580.rc: reg=0x0, val=0x1f40190
- [ 4.549399@3] meson-remote c8100580.rc: reg=0x4, val=0x12c00c8
- [ 4.555177@3] meson-remote c8100580.rc: reg=0x8, val=0x960050
- [ 4.560865@3] meson-remote c8100580.rc: reg=0xc, val=0x480028
- [ 4.566587@3] meson-remote c8100580.rc: reg=0x10, val=0x70fa0013
- [ 4.572514@3] meson-remote c8100580.rc: reg=0x18, val=0x8616800
- [ 4.578388@3] meson-remote c8100580.rc: reg=0x1c, val=0x9f00
- [ 4.583980@3] meson-remote c8100580.rc: reg=0x20, val=0x0
- [ 4.589343@3] meson-remote c8100580.rc: reg=0x24, val=0x0
- [ 4.594683@3] meson-remote c8100580.rc: reg=0x28, val=0x0
- [ 4.601108@0] input: aml_keypad as /devices/c8100580.rc/input/input0
- [ 4.607294@0] meson-remote: IR XMP protocol handler initialized
- [ 4.612604@3] input: adc_keypad as /devices/adc_keypad.50/input/input1
- [ 4.619176@0] gpio-key gpio_keypad.49: gpio_key: 0 name(power) pin()
- [ 4.625053@0] gpio-key gpio_keypad.49: amlogic_gpio_name_map_num pin 0!::
- [ 4.631695@0] gpio-key gpio_keypad.49: gpio_key: 0 power(147)
- [ 4.637426@0] gpio-key gpio_keypad.49: start setup_timer
- [ 4.642673@0] gpio-key gpio_keypad.49: power key(116) registed.
- [ 4.648751@3] input: gpio_keypad as /devices/gpio_keypad.49/input/input2
- [ 4.655329@3] gpio-key gpio_keypad.49: gpio keypad register input device completed.
- [ 4.662733@3] input input2: gpio keypad major:222
- [ 4.669106@3] Sensor: lsm303d_init
- [ 4.670994@3] Sensor: stk8313_init
- [ 4.674203@0] Sensor: stk831x_init
- [ 4.677597@3] Sensor: mxc622x_acc_init
- [ 4.681274@3] Sensor: mxc6255xc_acc_init
- [ 4.685271@3] Sensor: l3gd20_gyr_init
- [ 4.689798@3] aml dvb init
- [ 4.691547@3] DVB: probe amlogic dvb driver
- [ 4.695544@3] DVB: dmx rst ctl = ffffffc09ad59f40
- [ 4.700162@3] DVB: asyncfifo rst ctl = ffffffc09ad59fc0
- [ 4.705347@3] DVB: ahbarb0 rst ctl = ffffffc09ad59b00
- [ 4.710340@3] DVB: uparsertop rst ctl = ffffffc09ad59780
- [ 4.715732@3] DVB: ts0: serial
- [ 4.718716@3] DVB: ts0_control: 0x0
- [ 4.722065@3] DVB: ts0_invert: 0x0
- [ 4.725444@3] DVB: registering new adapter (amlogic-dvb)
- [ 4.731347@0] DVB: demux init
- [ 4.734149@0] DVB: demux init
- [ 4.736641@0] input input2: key 116 up
- [ 4.740949@0] DVB: demux init
- [ 4.743438@3] DVB:async fifo 0 buf size 524288, flush size 262144
- [ 4.749923@3] dtv params init
- [ 4.752410@3] dtv_params: probe dtv params driver : start
- [ 4.757591@3] /dtv_params: invalid GPIO pin, s_tunerPowerEnable_1_Pin=-2, skip this pin
- [ 4.765511@3] /dtv_params: invalid GPIO pin, s_demodReset_2_Pin=-2
- [ 4.771572@3] /dtv_params: invalid GPIO pin, s_antPower_2_Pin=-2, skip this pin
- [ 4.778867@3] /dtv_params: invalid GPIO pin, s_tunerPowerEnable_2_Pin=-2, skip this pin
- [ 4.786771@3] /dtv_params: invalid GPIO pin, s_userDefined_2_Pin=-2, skip this pin
- [ 4.794313@3] banks:215 is using the pin GPIODV_11 as gpio
- [ 4.799717@3] pinmux-gxl c1109880.pinmux: request() failed for pin 70
- [ 4.806082@3] pinmux-gxl c1109880.pinmux: pin-70 (dtv_params.52) status -22
- [ 4.812976@3] pinmux-gxl c1109880.pinmux: could not request pin 70 (GPIODV_11) from group dtv_params_pin on device c1109880.pinmux
- [ 4.824761@3] dtv-params dtv_params.52: Error applying setting, reverse things back
- [ 4.832300@3] set pinctrl : ffffffffffffffea
- [ 4.836703@3] dtv_params: probe dtv params driver : end
- [ 4.842143@3] Amlogic Demod DVB-T/C DebugIF Init
- [ 4.846506@0] Amlogic Demod DVB-T/C DebugIF Init ok----------------
- [ 4.854590@3] jtag: module init
- [ 4.856325@3] defendkey c8834500.defendkey: defendkey_devno:d900000
- [ 4.862039@0] defendkey c8834500.defendkey: defendkey: device defendkey created ok
- [ 4.869552@3] defendkey: driver init
- [ 4.873610@3] input: cec_input as /devices/virtual/input/input3
- [ 4.879030@3] cectx aocec: no hdmirx reg resource
- [ 4.883356@3] cectx aocec: no hhi reg resource
- [ 4.887779@3] cec: wake up flag:0
- [ 4.893104@0] aml_aes_dma c883e000.aml_aes: Aml AES_dma
- [ 4.896896@3] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
- [ 4.902323@3] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
- [ 4.908940@0] usbcore: registered new interface driver snd-usb-audio
- [ 4.916172@3] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
- [ 4.923609@0] aml-i2s-dai I2S.41: I2S Mic is in platform!
- [ 4.926969@3] aml_pcm_dai: pcm mode detection =1
- [ 4.931490@3] aml_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4
- [ 4.938174@3] aml_spdif_dai: set normal 512 fs /4 fs
- [ 4.943038@3] aml_spdif_dai: set 958 audio clk div 4
- [ 4.947970@3] aml_audio_hw: IEC958 16bit
- [ 4.951838@3] hdmitx: audio: aout notify rate 48000
- [ 4.956711@3] hdmitx: audio: aout notify size 16
- [ 4.961236@3] hdmitx: audio: aout notify format CT_PCM
- [ 4.966332@3] hdmtix: set audio
- [ 4.969441@3] hdmitx tx_aud_src = 0
- [ 4.972898@3] hdmitx: fs = 3, cd = 4, tmds_clk = 594000
- [ 4.978122@3] hdmitx aud_n_para = 6144
- [ 4.981819@3] hdmitx: audio: Audio Type: PCM
- [ 4.986050@3] hdmitx: audio: set audio param
- [ 4.991312@3] aml_snd_card: aml_multi_dev_parse_of ...
- [ 4.995324@3] aml_snd_card: no multi dev!
- [ 5.204665@3] aml_snd_card: headphone detection disable=1
- [ 5.204699@3] aml_snd_card: no spk event delay time set
- [ 5.210313@3] aml_snd_m8_card aml_m8_snd.48: T9015-audio-hifi <-> I2S.41 mapping ok
- [ 5.217822@3] aml_snd_m8_card aml_m8_snd.48: dit-hifi <-> SPDIF.42 mapping ok
- [ 5.224361@3] aml_pcm: enter aml_pcm_new dai->name: PCM.43 dai->id: 0
- [ 5.230855@3] aml_snd_m8_card aml_m8_snd.48: pcm2bt-pcm <-> PCM.43 mapping ok
- [ 5.237760@3] aml_snd_m8_card aml_m8_snd.48: ASoC: no source widget found for LOUTL
- [ 5.245321@3] aml_snd_m8_card aml_m8_snd.48: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
- [ 5.254109@3] aml_snd_m8_card aml_m8_snd.48: ASoC: no source widget found for LOUTR
- [ 5.261702@3] aml_snd_m8_card aml_m8_snd.48: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
- [ 5.272002@0] aml_snd_card: audio use jtag pinmux as i2s output, read val =0
- [ 5.272513@1] GACT probability NOT on
- [ 5.272521@1] Mirror/redirect action on
- [ 5.272526@1] u32 classifier
- [ 5.272526@1] Actions configured
- [ 5.272531@1] Netfilter messages via NETLINK v0.30.
- [ 5.272581@1] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
- [ 5.273047@3] ctnetlink v0.93: registering with nfnetlink.
- [ 5.273517@3] xt_time: kernel timezone is -0000
- [ 5.273602@3] ipip: IPv4 over IPv4 tunneling driver
- [ 5.318137@3] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 5.322646@3] arp_tables: (C) 2002 David S. Miller
- [ 5.328218@3] TCP: cubic registered
- [ 5.330697@3] Initializing XFRM netlink socket
- [ 5.336055@3] NET: Registered protocol family 10
- [ 5.340778@0] mip6: Mobile IPv6
- [ 5.342795@0] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 5.350769@0] sit: IPv6 over IPv4 tunneling driver
- [ 5.354474@0] NET: Registered protocol family 17
- [ 5.357715@0] NET: Registered protocol family 15
- [ 5.364530@0] Bridge firewalling registered
- [ 5.366424@0] Bluetooth: Can't register RFCOMM TTY driver
- [ 5.371716@0] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- [ 5.377221@0] Bluetooth: BNEP filters: protocol multicast
- [ 5.382473@0] Bluetooth: BNEP socket layer initialized
- [ 5.387545@0] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- [ 5.393609@0] Bluetooth: HIDP socket layer initialized
- [ 5.398765@0] l2tp_core: L2TP core driver, V2.0
- [ 5.403155@0] l2tp_ppp: PPPoL2TP kernel driver, V2.0
- [ 5.408121@0] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
- [ 5.413785@0] l2tp_netlink: L2TP netlink interface
- [ 5.418547@0] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
- [ 5.424604@0] l2tp_debugfs: L2TP debugfs support
- [ 5.429108@0] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
- [ 5.435741@0] NET: Registered protocol family 35
- [ 5.440327@0] Key type dns_resolver registered
- [ 5.447014@0] Registering SWP/SWPB emulation handler
- [ 5.450264@0] Loading compiled-in X.509 certificates
- [ 5.454588@0] regulator-dummy: disabling
- [ 5.460002@0] khadas-hym8563 2-0051: setting system clock to 2011-01-01 12:03:31 UTC (1293883411)
- [ 5.469531@0] hdmirx_ext: [hdmiin_drv_init] ver: Jul042016.1
- [ 5.473085@0] gxbb_pm: enter meson_pm_probe!
- [ 5.477074@0] gxbb_pm: meson_pm_probe done
- [ 5.482048@0] cpucore_cooling_register, max_cpu_core_num:4
- [ 5.486777@0] cpucore_cooling_register, max_cpu_core_num:4
- [ 5.507544@0] aml_istbt_dev_ready NULL
- [ 5.50760 5.512283@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
- [ 5.515676@0] Freeing unused kernel memory: 1340K (ffffffc001f5c000 - ffffffc0020ab000)
- [ 5.544661@0] init: init first stage started!
- [ 5.658477@0] audit: type=1403 audit(1293883411.690:2): policy loaded auid=4294967295 ses=4294967295
- [ 5.662626@0] init: (Initializing SELinux non-enforcing took 0.12s.)
- [ 5.671673@0] init: init second stage started!
- [ 5.678302@0] init: Running restorecon...
- [ 5.771928@0] init: waitpid failed: No child processes
- [ 5.772311@0] init: (Loading properties from /default.prop took 0.00s.)
- [ 5.780647@0] init: (Parsing /init.environ.rc took 0.00s.)
- [ 5.783857@0] init: (Parsing /init.usb.rc took 0.00s.)
- [ 5.789515@0] init: /init.amlogic.rc: 269: chmod requires 2 arguments
- [ 5.796396@0] init: (Parsing init.amlogic.usb.rc took 0.00s.)
- [ 5.801148@0] init: (Parsing init.amlogic.usb.rc took 0.00s.)
- [ 5.806400@0] init: (Parsing init.amlogic.board.rc took 0.01s.)
- [ 5.812626@0] init: (Parsing init.amlogic.usb.rc took 0.00s.)
- [ 5.817912@0] init: (Parsing init.amlogic.wifi.rc took 0.01s.)
- [ 5.823714@0] init: could not import file 'init.mtk.rc' from '/init.amlogic.rc': No such file or directory
- [ 5.833362@0] init: (Parsing /init.amlogic.rc took 0.04s.)
- [ 5.839503@0] init: (Parsing /init.usb.configfs.rc took 0.00s.)
- [ 5.844662@0] init: (Parsing /init.zygote64_32.rc took 0.00s.)
- [ 5.850277@0] init: (Parsing /init.rc took 0.07s.)
- [ 5.925053@0] init: Starting service 'ueventd'...
- [ 5.926262@0] init: insmod: open("/boot/optee.ko") failed: No such file or directory[ 5.927806@1] ueventd: ueventd started!
- [ 5.929984@1] ueventd: coldboot /sys/class
- [ 5.933338@1] ueventd: coldboot /sys/block
- [ 5.933385@1] ueventd: coldboot /sys/devices/virtual/tty/console
- [ 5.936079@1] ueventd: coldboot /sys/devices/virtual/tty/tty
- [ 5.936971@1] ueventd: coldboot /sys/devices/virtual/tty/ptmx
- [ 5.937926@2] ueventd: coldboot /sys/devices
- [ 5.965191@0] init: insmod: open("/boot/optee_armtz.ko") failed: No such file or directoryueventd: Coldboot took 0.34s.
- [[ 6.268254@7] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
- [ 6.268744@2] audit: type=1400 audit(1293883412.300:3): avc: denied { relabelto } for pid=3188 comm="ueventd" name="tty" dev="tmpfs" ino=3096 scontext=u:r:ueventd:s0 tcontext=
- u:object_r:owntty_device:s0 tclass=chr_file permissive=1
- [ 6.269606@2] audit: type=1400 audit(1293883412.300:4): avc: denied { relabelfrom } for pid=3188 comm="ueventd" name="ptmx" dev="tmpfs" ino=9871 scontext=u:r:ueventd:s0 tconte
- xt=u:object_r:ptmx_device:s0 tclass=chr_file permissive=1
- [ 6.269627@2] audit: type=1400 audit(1293883412.300:5): avc: denied { relabelto } for pid=3188 comm="ueventd" name="ptmx" dev="tmpfs" ino=9871 scontext=u:r:ueventd:s0 tcontext
- =u:object_r:ptmx_device:s0 tclass=chr_file permissive=1
- [ 6.280099@2] audit: type=1400 audit(1293883412.310:6): avc: denied { relabelfrom } for pid=3188 comm="ueventd" name="console" dev="tmpfs" ino=3095 scontext=u:r:ueventd:s0 tco
- ntext=u:object_r:console_device:s0 tclass=chr_file permissive=1
- [ 6.280122@2] audit: type=1400 audit(1293883412.310:7): avc: denied { relabelto } for pid=3188 comm="ueventd" name="console" dev="tmpfs" ino=3095 scontext=u:r:ueventd:s0 tcont
- ext=u:object_r:console_device:s0 tclass=chr_file permissive=1
- [ 6.810239@1] ueventd: Coldboot tty took 0.54s.
- [ 6.935955@1] fb: afbc: 1
- [ 6.936637@1] init: enter do_confirm_formated /dev/block/tee, /tee
- [ 6.939094@1] init: blocksize 1024, bytes_per_inode 1024
- [ 6.944370@1] init: do_confirm_formated ext4 try mount
- [ 6.956193@1] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
- [ 7.010408@1] fs_mgr: only system!, ignore mount_point:/misc
- [ 7.014045@1] EXT4-fs (mmcblk0p12): mounted filesystem with ordered data mode. Opts: (null)
- [ 7.018913@1] fs_mgr: __mount(source=/dev/block/system,target=/system,type=ext4)=0
- [ 7.026382@1] fs_mgr: only system!, ignore mount_point:/cache
- [ 7.031916@1] fs_mgr: only system!, ignore mount_point:/data
- [ 7.037573@1] fs_mgr: only system!, ignore mount_point:/swap_zram0
- [ 7.043645@1] fs_mgr: only system!, ignore mount_point:/tee
- [ 7.053879@7] fs_mgr: ignore system!, ignore mount_point:/system
- [ 7.055700@1] EXT4-fs (mmcblk0p3): Ignoring removed nomblk_io_submit option
- [ 7.069986@2] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit
- [ 7.070522@1] random: accelerateboot urandom read with 61 bits of entropy available
- [ 7.070732@1] audit: type=1400 audit(1293883413.100:8): avc: denied { module_request } for pid=4137 comm="accelerateboot" kmod="personality-8" scontext=u:r:accelerateboot:s0 t
- context=u:r:kernel:s0 tclass=system permissive=1
- [ 7.102793@2] fs_mgr: check_fs(): mount(/dev/block/cache,/cache,ext4)=0: Success
- [ 7.158410@1] accelerate: old buffer is: 1408
- [ 7.179156@4] fs_mgr: check_fs(): unmount(/cache) succeeded
- [ 7.179462@4] fs_mgr: Running /system/bin/e2fsck on /dev/block/cache
- [ 7.269443@4] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
- [ 7.269443@4]
- [ 7.270196@4] e2fsck: Pass 1: Checking inodes, blocks, and sizes
- [ 7.270196@4]
- [ 7.277817@4] e2fsck: Pass 2: Checking directory structure
- [ 7.277817@4]
- [ 7.284883@4] e2fsck: Pass 3: Checking directory connectivity
- [ 7.284883@4]
- [ 7.292162@4] e2fsck: Pass 4: Checking reference counts
- [ 7.292162@4]
- [ 7.299069@4] e2fsck: Pass 5: Checking group summary information
- [ 7.299069@4]
- [ 7.306655@0] e2fsck: /dev/block/cache: 27/32768 files (3.7% non-contiguous), 4344/131072 blocks
- [ 7.306655@0]
- [ 7.317884@0] EXT4-fs (mmcblk0p3): Ignoring removed nomblk_io_submit option
- [ 7.328719@0] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
- [ 7.335092@0] fs_mgr: __mount(source=/dev/block/cache,target=/cache,type=ext4)=0
- [ 7.342832@0] EXT4-fs (mmcblk0p13): Ignoring removed nomblk_io_submit option
- [ 7.369252@1] EXT4-fs (mmcblk0p13): 2 orphan inodes deleted
- [ 7.369289@1] EXT4-fs (mmcblk0p13): recovery complete
- [ 7.387413@1] EXT4-fs (mmcblk0p13): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit
- [ 7.392703@1] fs_mgr: check_fs(): mount(/dev/block/data,/data,ext4)=0: Success
- [ 7.394330@6] audit: type=1400 audit(1293883413.420:9): avc: denied { read } for pid=4137 comm="accelerateboot" name="vold" dev="mmcblk0p12" ino=498 scontext=u:r:accelerateboo
- t:s0 tcontext=u:object_r:vold_exec:s0 tclass=file permissive=1
- [ 7.394366@6] audit: type=1400 audit(1293883413.420:10): avc: denied { open } for pid=4137 comm="accelerateboot" path="/system/bin/vold" dev="mmcblk0p12" ino=498 scontext=u:r:
- accelerateboot:s0 tcontext=u:object_r:vold_exec:s0 tclass=file permissive=1
- [ 7.407739@0] audit: type=1400 audit(1293883413.440:11): avc: denied { read } for pid=4137 comm="accelerateboot" name="sgdisk" dev="mmcblk0p12" ino=439 scontext=u:r:accelerate
- boot:s0 tcontext=u:object_r:sgdisk_exec:s0 tclass=file permissive=1
- [ 7.407770@0] audit: type=1400 audit(1293883413.440:12): avc: denied { open } for pid=4137 comm="accelerateboot" path="/system/bin/sgdisk" dev="mmcblk0p12" ino=439 scontext=u:
- r:accelerateboot:s0 tcontext=u:object_r:sgdisk_exec:s0 tclass=file permissive=1
- [ 7.414333@0] audit: type=1400 audit(1293883413.440:13): avc: denied { read } for pid=4137 comm="accelerateboot" name="blkid" dev="mmcblk0p12" ino=211 scontext=u:r:accelerateb
- oot:s0 tcontext=u:object_r:blkid_exec:s0 tclass=file permissive=1
- [ 7.414355@0] audit: type=1400 audit(1293883413.440:14): avc: denied { open } for pid=4137 comm="accelerateboot" path="/system/bin/blkid" dev="mmcblk0p12" ino=211 scontext=u:r
- :accelerateboot:s0 tcontext=u:object_r:blkid_exec:s0 tclass=file permissive=1
- [ 7.475285@5] audit: type=1400 audit(1293883413.510:15): avc: denied { read } for pid=4137 comm="accelerateboot" name="keystore" dev="mmcblk0p12" ino=320 scontext=u:r:accelera
- teboot:s0 tcontext=u:object_r:keystore_exec:s0 tclass=file permissive=1
- [ 7.475321@5] audit: type=1400 audit(1293883413.510:16): avc: denied { open } for pid=4137 comm="accelerateboot" path="/system/bin/keystore" dev="mmcblk0p12" ino=320 scontext=
- u:r:accelerateboot:s0 tcontext=u:object_r:keystore_exec:s0 tclass=file permissive=1
- [ 7.628177@1] fs_mgr: check_fs(): unmount(/data) succeeded
- [ 7.628239@1] fs_mgr: Running /system/bin/e2fsck on /dev/block/data
- [ 8.509603@6] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
- [ 8.509603@6]
- [ 8.510354@6] e2fsck: Pass 1: Checking inodes, blocks, and sizes
- [ 8.510354@6]
- [ 8.517965@6] e2fsck: Pass 2: Checking directory structure
- [ 8.517965@6]
- [ 8.525027@6] e2fsck: Pass 3: Checking directory connectivity
- [ 8.525027@6]
- [ 8.532331@6] e2fsck: Pass 4: Checking reference counts
- [ 8.532331@6]
- [ 8.539182@6] e2fsck: Pass 5: Checking group summary information
- [ 8.539182@6]
- [ 8.546805@0] e2fsck: /dev/block/data: 2339/1721760 files (12.9% non-contiguous), 300995/6883072 blocks
- [ 8.546805@0]
- [ 8.559982@0] random: nonblocking pool is initialized
- [ 8.579693@0] EXT4-fs (mmcblk0p13): Ignoring removed nomblk_io_submit option
- [ 8.586808@0] EXT4-fs (mmcblk0p13): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
- [ 8.592667@0] fs_mgr: __mount(source=/dev/block/data,target=/data,type=ext4)=0
- [ 8.617029@0] EXT4-fs (mmcblk0p8): Ignoring removed nomblk_io_submit option
- [ 8.620020@0] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit
- [ 8.629183@0] fs_mgr: check_fs(): mount(/dev/block/tee,/tee,ext4)=0: Success
- [ 8.689088@7] fs_mgr: check_fs(): unmount(/tee) succeeded
- [ 8.689172@7] fs_mgr: Running /system/bin/e2fsck on /dev/block/tee
- [ 8.731379@7] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
- [ 8.731379@7]
- [ 8.732127@7] e2fsck: Pass 1: Checking inodes, blocks, and sizes
- [ 8.732127@7]
- [ 8.739721@7] e2fsck: Pass 2: Checking directory structure
- [ 8.739721@7]
- [ 8.746798@7] e2fsck: Pass 3: Checking directory connectivity
- [ 8.746798@7]
- [ 8.754110@7] e2fsck: Pass 4: Checking reference counts
- [ 8.754110@7]
- [ 8.760987@7] e2fsck: Pass 5: Checking group summary information
- [ 8.760987@7]
- [ 8.768582@0] e2fsck: /dev/block/tee: 11/8192 files (0.0% non-contiguous), 3112/8192 blocks
- [ 8.768582@0]
- [ 8.788010@0] EXT4-fs (mmcblk0p8): Ignoring removed nomblk_io_submit option
- [ 8.791077@0] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
- [ 8.800633@0] fs_mgr: __mount(source=/dev/block/tee,target=/tee,type=ext4)=0
- [ 8.808035@7] init: here: 1, 1 mount_mode:512
- [ 8.845353@7] accelerate: Error reading block data /data/property/persist.sys.profiler_ms
- [ 8.845357@5] accelerate: Error reading block data /system/framework/arm64/boot-ext.art
- [ 8.873220@7] Adding 511996k swap on /dev/block/zram0. Priority:-1 extents:1 across:511996k SS
- [ 8.881594@6] accelerate: Error reading block data /system/framework/arm/boot-framework.oat
- [ 8.887630@4] init: cannot find '/system/bin/tee-supplicant' (No such file or directory), disabling 'tee_supplicant'
- [ 8.898874@4] init: /recovery not specified in fstab
- [ 8.899375@1] logd.auditd: start
- [ 8.899421@1] logd.klogd: 8804957294
- [ 8.952813@6] accelerate: Error reading block data /system/lib/libwebviewchromium_plat_support.so
- [ 8.963480@1] type=1400 audit(1293883414.950:17): avc: denied { search } for pid=4148 comm="accelerateboot" name="com.google.android.gms" dev="mmcblk0p13" ino=481597 scontext=u:r
- :accelerateboot:s0 tcontext=u:object_r:app_data_file:s0:c512,c768 tclass=dir permissive=1
- [ 8.982130@1] type=1400 audit(1293883414.950:18): avc: denied { module_request } for pid=4167 comm="debuggerd" kmod="personality-8" scontext=u:r:debuggerd:s0 tcontext=u:r:kernel:
- s0 tclass=system permissive=1
- [ 8.995813@6] accelerate: Error reading block data /system/lib/libart-compiler.so
- [ 8.997134@2] dig: dig start!
- [ 9.010440@1] type=1400 audit(1293883414.960:19): avc: denied { search } for pid=4148 comm="accelerateboot" name="keystore" dev="mmcblk0p13" ino=995525 scontext=u:r:accelerateboo
- t:s0 tcontext=u:object_r:keystore_data_file:s0 tclass=dir permissive=1
- [ 9.032226@1] type=1400 audit(1293883414.960:20): avc: denied { read } for pid=4148 comm="accelerateboot" name=".metadata" dev="mmcblk0p13" ino=995563 scontext=u:r:accelerateboot
- :s0 tcontext=u:object_r:keystore_data_file:s0 tclass=file permissive=1
- [ 9.054003@1] type=1400 audit(1293883414.960:21): avc: denied { open } for pid=4148 comm="accelerateboot" path="/data/misc/keystore/.metadata" dev="mmcblk0p13" ino=995563 scontex
- t=u:r:accelerateboot:s0 tcontext=u:object_r:keystore_data_file:s0 tclass=file permissive=1
- [ 9.077497@1] type=1400 audit(1293883414.980:22): avc: denied { open } for pid=4148 comm="accelerateboot" path="/data/user_de/0/eu.chainfire.supersu/files/supersu.cfg" dev="mmcbl
- k0p13" ino=946666 scontext=u:r:accelerateboot:s0 tcontext=u:object_r:app_data_file:s0:c512,c768 tclass=file permissive=1
- [ 9.129460@4] accelerate: Error reading block data /system/fonts/NotoSansTelugu-Regular.ttf
- [ 9.131574@1] type=1400 audit(1293883415.160:23): avc: denied { read } for pid=4148 comm="accelerateboot" name="base.apk" dev="mmcblk0p13" ino=734403 scontext=u:r:accelerateboot:
- s0 tcontext=u:object_r:apk_data_file:s0 tclass=file permissive=1
- [ 9.131695@1] type=1400 audit(1293883415.160:24): avc: denied { open } for pid=4148 comm="accelerateboot" path="/data/app/com.android.chrome-1/base.apk" dev="mmcblk0p13" ino=7344
- 03 scontext=u:r:accelerateboot:s0 tcontext=u:object_r:apk_data_file:s0 tclass=file permissive=1
- [ 9.167376@0] init: decode_uid: Unable to find UID for 'pppoe'. Returning UINT_MAX
- [ 9.168647@0] init: decode_uid: Unable to find UID for 'pppoe'. Returning UINT_MAX
- [ 9.297502@6] accelerate: Error reading block data /system/lib/libkeystore_binder.so
- [ 9.300930@4] mali_kbase: unknown parameter 'mali_debug_level' ignored
- [ 9.303024@6] accelerate: Error reading block data /system/framework/oat/arm64/services.odex
- [ 9.303028@5] accelerate: Error reading block data /data/user_de/0/com.android.bluetooth/shared_prefs/OPPMGR.xml
- [ 9.324586@4] mali_kbase: unknown parameter 'mali_shared_mem_size' ignored
- [ 9.334016@1] ftrace: Allocated trace_printk buffers
- [ 9.336748@1] mali d00c0000.t82x: Continuing without Mali regulator control
- [ 9.343209@1] mali d00c0000.t82x: set min pp to default 1
- [ 9.348532@1] mali d00c0000.t82x: set min clk default to 0
- [ 9.354003@1] mali d00c0000.t82x: dvfs table is 5
- [ 9.358604@1] mali d00c0000.t82x: dvfs table addr ffffffc09a3ba818, ele size=48
- [ 9.365851@1] mali d00c0000.t82x: max clk set 3
- [ 9.370320@1] mali d00c0000.t82x: turbo clk set to 4
- [ 9.375251@1] mali d00c0000.t82x: default clk set to 1
- [ 9.380393@1] mali_plat=ffffffbffc04b4e0
- [ 9.384715@1] gpu cooling register okay with err=0
- [ 9.389162@1] gpu core cooling register okay with err=0
- [ 9.394345@1] gpu_power_main, 63
- [ 9.397595@1] hrtimer: interrupt took 14625 ns
- [ 9.402101@1] mali d00c0000.t82x: GPU identified as 0x0820 r1p0 status 0
- [ 9.409709@0] mali d00c0000.t82x: Probed as mali0
- [ 9.413568@0] init: insmod: open("/system/lib/dovi.ko") failed: No such file or directory
- [ 9.607191@3] binder: 4223:4223 transaction failed 29189, size 0-0
- [ 9.608994@3] init: insmod: open("/system/lib/aml_thermal.ko") failed: No such file or directory
- [ 9.617539@3] logd.daemon: reinit
- [ 9.618216@5] ddr_window,module_VER_:2017-03-18-11-13
- [ 9.628416@1] type=1400 audit(1293883415.660:25): avc: denied { getattr } for pid=4225 comm="hdmi_cec" path="/vendor" dev="rootfs" ino=2076 scontext=u:r:hdmi_cec:s0 tcontext=u:ob
- ject_r:rootfs:s0 tclass=lnk_file permissive=1
- [ 9.642170@0] amlkey_init() enter!
- [ 9.646788@0] emmc_key_read:428, read ok
- [ 9.646802@0] amlkey_init() storagekey_info.buffer=ffffff8001900000, storagekey_info.size = 40000!
- [ 9.648103@0] vfm_map_store:rm default
- [ 9.648133@0] vfm_map_store:add default decoder ppmgr deinterlace amvideo
- [ 9.648188@0] init: property_set("ro.radio.noril", "true") failed
- [ 9.648237@0] fb: afbc: 1
- [ 9.651698@0] android_usb: Cannot enable 'adb' (-22)init: cannot find '/system/bin/tee-supplicant' (No such file or directory), disabling 'tee_supplicant'
- [ 9.651891@0] init: cannot find '/system/bin/update_verifier' (No such file or directory), disabling 'exec 2 (/system/bin/update_verifier)'
- [ 9.652246@0] init: Service flash_recovery does not have a SELinux domain defined.
- [ 9.654416@0] init: Service ddrtest does not have a SELinux domain defined.
- [ 9.654574@0] init: cannot find '/system/bin/factoryreset.sh' (No such file or directory), disabling 'factoryreset'
- [ 9.658860@6] init: couldn't write 4243 to /dev/cpuset/camera-daemon/tasks: No such file or directory
- [ 9.663297@2] meson-remote c8100580.rc: remote_ioctl invalid user space pointer
- [ 9.663798@2] meson-remote�� 9.755143@1] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
- [ 9.765094@5] type=1400 audit(1293883415.680:26): avc: denied { setattr } for pid=1 comm="init" name="env" dev="tmpfs" ino=329 scontext=u:r:init:s0 tcontext=u:object_r:env_device
- :s0 tclass=blk_file permissive=1
- [ 9.767493@4] set hdcp_pwr 1
- [ 9.771216@3] fb: osd_open index=0,open_count=1
- [ 9.771220@3] fb: use ion buffer for fb memory
- [ 9.771252@3] fb: OSD0 as afbcd mode
- [ 9.771451@3] meson-fb meson-fb.15: create ion_client ffffffc09120f480, handle=ffffffc0932d0f00
- [ 9.771455@3] meson-fb meson-fb.15: ion memory(0): created fb at 0x00000000afd4e000, size 8 MiB
- [ 9.771459@3] fb: 0, phy: 0x00000000afd4e000, vir:0xffffff80031ff000, size=8300K
- [ 9.771459@3]
- [ 9.771624@3] meson-fb meson-fb.15: create ion_client ffffffc09120f480, handle=ffffffc0933520c0
- [ 9.771628@3] meson-fb meson-fb.15: ion memory(0): created fb at 0x00000000b0569000, size 8 MiB
- [ 9.771631@3] fb: 0, phy: 0x00000000b0569000, vir:0xffffff8003a1b000, size=8300K
- [ 9.771631@3]
- [ 9.771768@3] meson-fb meson-fb.15: create ion_client ffffffc09120f480, handle=ffffffc0933521c0
- [ 9.771772@3] meson-fb meson-fb.15: ion memory(0): created fb at 0x00000000b0d84000, size 8 MiB
- [ 9.771774@3] fb: 0, phy: 0x00000000b0d84000, vir:0xffffff8004237000, size=8300K
- [ 9.771774@3]
- [ 9.771779@3] fb: Frame buffer memory assigned at
- [ 9.771779@3] fb: 0, phy: 0x00000000afd4e000, vir:0xffffff80031ff000, size=8300K
- [ 9.771779@3]
- [ 9.771782@3] fb: 0, phy: 0x00000000afd4e000, vir:0xffffff80031ff000, size=8300K
- [ 9.771782@3]
- [ 9.771784@3] fb: 0, phy: 0x00000000b0569000, vir:0xffffff8003a1b000, size=8300K
- [ 9.771784@3]
- [ 9.771786@3] fb: 0, phy: 0x00000000b0d84000, vir:0xffffff8004237000, size=8300K
- [ 9.771786@3]
- [ 9.771789@3] fb: ---------------clear fb0 memory ffffff80031ff000
- [ 9.774341@3] fb: ---------------clear fb0 memory ffffff8003a1b000
- [ 9.776860@3] fb: ---------------clear fb0 memory ffffff8004237000
- [ 9.779104@3] fb: osd[0] canvas.idx =0x40
- [ 9.779106@3] fb: osd[0] canvas.addr=0xafd4e000
- [ 9.779107@3] fb: osd[0] canvas.width=7680
- [ 9.779109@3] fb: osd[0] canvas.height=3240
- [ 9.779110@3] fb: osd[0] frame.width=1920
- [ 9.779111@3] fb: osd[0] frame.height=1080
- [ 9.877174@4] restore hdcp_pwr 0
- [ 9.879517@4] hdmitx: set frac_rate_policy as 0
- [ 9.879808@4] sname = 2160p60hz
- [ 9.879812@4] char_clk = 594000
- [ 9.879813@4] cd = 4
- [ 9.879815@4] cs = 3
- [ 9.879819@4] RX tmds clk: 300 Calc clk: 297
- [ 9.979351@4] type=1400 audit(1293883415.690:27): avc: denied { module_request } for pid=4237 comm="imageserver" kmod="personality-8" scontext=u:r:imageserver:s0 tcontext=u:r:ker
- nel:s0 tclass=system permissive=1
- [ 9.980058@4] type=1400 audit(1293883415.690:28): avc: denied { getattr } for pid=4237 comm="imageserver" path="/vendor" dev="rootfs" ino=2076 scontext=u:r:imageserver:s0 tcontex
- t=u:object_r:rootfs:s0 tclass=lnk_file permissive=1
- [ 9.980277@4] type=1400 audit(1293883415.700:29): avc: denied { getattr } for pid=4236 comm="pppoe_wrapper" path="/vendor" dev="rootfs" ino=2076 scontext=u:r:pppoe_wrapper:s0 tco
- ntext=u:object_r:rootfs:s0 tclass=lnk_file permissive=1
- [ 9.980456@4] type=1400 audit(1293883415.720:30): avc: denied { module_request } for pid=4248 comm="mediacodec" kmod="personality-8" scontext=u:r:mediacodec:s0 tcontext=u:r:kerne
- l:s0 tclass=system permissive=1
- [ 9.980612@4] type=1400 audit(1293883415.730:31): avc: denied { module_request } for pid=4244 comm="drmserver" kmod="personality-8" scontext=u:r:drmserver:s0 tcontext=u:r:kernel:
- s0 tclass=system permissive=1
- [ 9.981232@4] type=1400 audit(1293883415.730:32): avc: denied { getattr } for pid=4248 comm="mediacodec" path="/vendor" dev="rootfs" ino=2076 scontext=u:r:mediacodec:s0 tcontext=
- u:object_r:rootfs:s0 tclass=lnk_file permissive=1
- [ 9.981410@4] type=1400 audit(1293883415.740:33): avc: denied { module_request } for pid=4258 comm="mediaextractor" kmod="personality-8" scontext=u:r:mediaextractor:s0 tcontext=u
- :r:kernel:s0 tclass=system permissive=1
- [ 9.982011@4] type=1400 audit(1293883415.760:34): avc: denied { module_request } for pid=4249 comm="mediadrmserver" kmod="personality-8" scontext=u:r:mediadrmserver:s0 tcontext=u
- :r:kernel:s0 tclass=system permissive=1
- [ 9.982680@4] type=1400 audit(1293883415.790:35): avc: denied { open } for pid=4224 comm="systemcontrol" path="/dev/__properties__/u:object_r:logpersistd_logging_prop:s0" dev="tm
- pfs" ino=287 scontext=u:r:system_control:s0 tcontext=u:object_r:logpersistd_logging_prop:s0 tclass=file permissive=1
- [ 9.982892@4] type=1400 audit(1293883415.790:36): avc: denied { getattr } for pid=4224 comm="systemcontrol" path="/dev/__properties__/u:object_r:logpersistd_logging_prop:s0" dev=
- "tmpfs" ino=287 scontext=u:r:system_control:s0 tcontext=u:object_r:logpersistd_logging_prop:s0 tclass=file permissive=1
- [ 9.983081@4] type=1400 audit(1293883415.800:37): avc: denied { getattr } for pid=4249 comm="mediadrmserver" path="/vendor" dev="rootfs" ino=2076 scontext=u:r:mediadrmserver:s0 t
- context=u:object_r:rootfs:s0 tclass=lnk_file permissive=1
- kvim2:/ $ [ 10.214371@0] fb: osd_open index=1,open_count=1
- [ 10.215293@0] fb: use ion buffer for fb memory
- [ 10.219703@0] meson-fb meson-fb.15: create ion_client ffffffc09120f480, handle=ffffffc09a241680
- [ 10.228414@0] meson-fb meson-fb.15: ion memory(1): created fb at 0x00000000b159f000, size 1 MiB
- [ 10.236922@0] fb: Frame buffer memory assigned at
- [ 10.241459@0] fb: 1, phy: 0x00000000b159f000, vir:0xffffff800547f000, size=1024K
- [ 10.241459@0]
- [ 10.250664@0] fb: fb1 open, logo index:1
- [ 10.528050@2] type=1400 audit(1293883416.560:38): avc: denied { getattr } for pid=4355 comm="bootanimation" path="/vendor" dev="rootfs" ino=2076 scontext=u:r:bootanim:s0 tcontext
- =u:object_r:rootfs:s0 tclass=lnk_file permissive=1
- [ 10.609118@7] healthd: No battery devices found
- [ 10.664579@2] type=1400 audit(1293883416.690:39): avc: denied { read } for pid=4137 comm="accelerateboot" name="preinstall.sh" dev="mmcblk0p12" ino=396 scontext=u:r:accelerateboo
- t:s0 tcontext=u:object_r:preinstall_exec:s0 tclass=file permissive=1
- [ 10.680917@2] type=1400 audit(1293883416.690:40): avc: denied { open } for pid=4137 comm="accelerateboot" path="/system/bin/preinstall.sh" dev="mmcblk0p12" ino=396 scontext=u:r:a
- ccelerateboot:s0 tcontext=u:object_r:preinstall_exec:s0 tclass=file permissive=1
- [ 11.228377@1] type=1403 audit(1293883417.260:41): policy loaded auid=4294967295 ses=4294967295
- [ 11.238740@3] warning: `daemonsu' uses 32-bit capabilities (legacy support in use)
- [ 11.646278@6] fb: osd[1] enable: 0 scale:0x0 (systemcontrol)
- [ 11.646319@6] fb: osd[0] enable: 1 scale:0x10001 (systemcontrol)
- [ 11.655439@6] fb: free_scale_switch to fb0, mode: 0x10001
- [ 11.658981@6] vout_serve: osd0=> x:0,y:0,w:1920,h:1080
- [ 11.658981@6] osd1=> x:0,y:0,w:18,h:18
- [ 11.666502@6] fb: current vmode=2160p60hz, cmd: 0x30000
- [ 11.672955@6] fb: osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
- [ 11.677904@6] fb: osd[1].scaledata: 1920 3840 1080 2160
- [ 11.683052@6] fb: osd[1].pandata: 0 0 0 0
- [ 12.076897@7] type=1403 audit(1293883418.110:42): policy loaded auid=4294967295 ses=4294967295
- [ 12.085426@3] EXT4-fs (mmcblk0p12): warning: maximal mount count reached, running e2fsck is recommended
- [ 12.089554@3] EXT4-fs (mmcblk0p12): re-mounted. Opts: (null)
- [ 12.252752@4] EXT4-fs (mmcblk0p12): re-mounted. Opts: (null)
- [ 14.357726@0] request_suspend_state: wakeup (3->0) at 14263269422 (2011-01-01 12:03:40.397810337 UTC)
- [ 14.361286@0] request_suspend_state,164,old_sleep=0,new_state=0
- [ 17.619600@4] lowmemorykiller: lowmem_shrink: convert oom_adj to oom_score_adj:
- [ 17.621278@4] lowmemorykiller: oom_adj 0 => oom_score_adj 0
- [ 17.626876@4] lowmemorykiller: oom_adj 2 => oom_score_adj 117
- [ 17.632494@4] lowmemorykiller: oom_adj 4 => oom_score_adj 235
- [ 17.638216@4] lowmemorykiller: oom_adj 6 => oom_score_adj 352
- [ 17.643876@4] lowmemorykiller: oom_adj 9 => oom_score_adj 529
- [ 17.649656@5] lowmemorykiller: oom_adj 15 => oom_score_adj 1000
- [ 18.888138@5] aml_wifi wifi.34: [usb_power_control] Set WiFi power down
- [ 18.895767@7] type=1400 audit(1293883424.930:43): avc: denied { getattr } for pid=4788 comm="bcmdl" path="/vendor" dev="rootfs" ino=2076 scontext=u:r:bcmdl:s0 tcontext=u:object_r
- :rootfs:s0 tclass=lnk_file permissive=1
- [ 18.975359@1] avc open
- [ 18.975391@1] amvenc_avc check CMA pool sucess, max instance: 3.
- [ 18.978164@1] allocating phys 0x9fb00000, size 20480k, wq:ffffffc097187a00.
- [ 18.985356@1] amvenc_avc memory config sucess, buff start:0x9fb00000, size is 0x1400000, wq:ffffffc097187a00.
- [ 18.995266@1] avc release, wq:ffffffc097187a00
- [ 18.999376@1] remove encode_work_queue ffffffc097187a00 sucess, _destroy_encode_work_queue line 3450.
- [ 19.108863@2] aml_wifi wifi.34: [usb_power_control] Set WiFi power on !
- [ 19.111016@0] [aml_sd_emmc_irq] sdio: resp_timeout,vstat:0xa3ff2800,virqc:3fff
- [ 19.117005@0] [aml_host_bus_fsm_show] sdio: err: wait for irq service, bus_fsm:0x8
- [ 19.124360@6] aml_sd_emmc_data_thread 2642 sdio: cmd:52
- [ 19.130871@0] [aml_sd_emmc_irq] sdio: resp_timeout,vstat:0xa3ff2800,virqc:3fff
- [ 19.135862@6] codec:vdec_create instance ffffff80070e8000, total 1
- [ 19.135905@6] codec:vdec_release instance ffffff80070e8000, total 0
- [ 19.136122@6] codec:vdec_create instance ffffff80070fb000, total 1
- [ 19.136149@6] codec:vdec_release instance ffffff80070fb000, total 0
- [ 19.136278@6] ionvid: info: ionvideo open
- [ 19.165480@6] [aml_host_bus_fsm_show] sdio: err: wait for irq service, bus_fsm:0x8
- [ 19.172843@6] aml_sd_emmc_data_thread 2642 sdio: cmd:52
- [ 19.182968@0] [aml_sd_emmc_irq] sdio: resp_timeout,vstat:0xa3ff2800,virqc:3fff
- [ 19.185317@0] [aml_host_bus_fsm_show] sdio: err: wait for irq service, bus_fsm:0x8
- [ 19.192672@6] aml_sd_emmc_data_thread 2642 sdio: cmd:8
- [ 19.198652@6] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 19.312115@4] sdio: queuing unknown CIS tuple 0x80 (150 bytes)
- [ 19.334501@6] ionvid: info: ionvideo_stop_generating!!!!
- [ 19.334561@6] ionvid: info: ionvideo release
- [ 19.357592@7] sdio: queuing unknown CIS tuple 0x48 (68 bytes)
- [ 19.360804@7] sdio: clk 200000000 SDR mode tuning start
- [ 19.363571@7] sdio: rx_tuning_result[1] = 10
- [ 19.368019@5] sdio: rx_tuning_result[2] = 10
- [ 19.372029@5] sdio: rx_tuning_result[3] = 10
- [ 19.376029@5] sdio: rx_tuning_result[4] = 10
- [ 19.382071@5] sdio: best_win_start =1, best_win_size =4
- [ 19.385319@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x32000
- [ 19.392318@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x32000
- [ 19.399084@6] codec:vdec_create instance ffffff8007396000, total 1
- [ 19.405115@6] codec:vdec_release instance ffffff8007396000, total 0
- [ 19.411779@6] codec:vdec_create instance ffffff80073b1000, total 1
- [ 19.417124@6] codec:vdec_release instance ffffff80073b1000, total 0
- [ 19.423793@6] ionvid: info: ionvideo open
- [ 19.429551@3] sdio: queuing unknown CIS tuple 0x91 (3 bytes)
- [ 19.432726@3] sdio: new ultra high speed SDR104 SDIO card at address 0001
- [ 19.439532@3] sdio: clock 200000000, 4-bit-bus-width
- [ 19.447720@2] [sdio_reinit] finish
- [ 19.632780@5] BT_RADIO going: off
- [ 19.632813@5] BCM_BT: going OFF
- [ 19.634494@1] ionvid: info: ionvideo_stop_generating!!!!
- [ 19.638870@1] ionvid: info: ionvideo release
- [ 19.648429@2] aml_wifi wifi.34: [wifi_power_ioctl] ioctl Set sdio wifi power up!
- [ 19.650523@2] aml_wifi wifi.34: [wifi_power_ioctl] wifi interface dev type: sdio, length = 4
- [ 19.655841@5] BT_RADIO going: on
- [ 19.655844@5] BCM_BT: going ON
- [ 19.693389@7] codec:vdec_create instance ffffff80076a3000, total 1
- [ 19.693996@7] codec:vdec_release instance ffffff80076a3000, total 0
- [ 19.700624@7] codec:vdec_create instance ffffff80076b6000, total 1
- [ 19.706971@7] codec:vdec_release instance ffffff80076b6000, total 0
- [ 19.713014@7] ionvid: info: ionvideo open
- [ 19.775945@0] cfg80211: Calling CRDA to update world regulatory domain
- [ 19.791742@3] dhd_module_init: in Dongle Host Driver, version 1.363.59.144.9 (r)
- [ 19.793533@3] ======== dhd_wlan_init_plat_data ========
- [ 19.798825@3] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
- [ 19.803778@3] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
- [ 19.809181@3] dhd_wlan_init_gpio: host_oob_irq: 100
- [ 19.813957@3] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
- [ 19.819437@3] dhd_wifi_platform_load: Enter
- [ 19.823561@3] Power-up adapter 'DHD generic adapter'
- [ 19.828484@3] wifi_platform_set_power = 1
- [ 19.832405@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 19.837741@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 19.914534@0] ionvid: info: ionvideo_stop_generating!!!!
- [ 19.914597@0] ionvid: info: ionvideo release
- [ 19.930204@5] codec:vdec_create instance ffffff80076d8000, total 1
- [ 19.930803@5] codec:vdec_release instance ffffff80076d8000, total 0
- [ 19.937327@5] codec:vdec_create instance ffffff80076eb000, total 1
- [ 19.943192@5] codec:vdec_release instance ffffff80076eb000, total 0
- [ 19.949768@5] ionvid: info: ionvideo open
- [ 20.044711@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 20.076841@0] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 0 to 9600
- [ 20.079227@0] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 9600 to 9600
- [ 20.087333@0] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 9600 to 115200
- [ 20.100451@2] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 115200 to 2000000
- [ 20.144498@1] ionvid: info: ionvideo_stop_generating!!!!
- [ 20.144559@1] ionvid: info: ionvideo release
- [ 20.162254@4] codec:vdec_create instance ffffff8007702000, total 1
- [ 20.162866@4] codec:vdec_release instance ffffff8007702000, total 0
- [ 20.169413@4] codec:vdec_create instance ffffff8007715000, total 1
- [ 20.175295@4] codec:vdec_release instance ffffff8007715000, total 0
- [ 20.181635@4] ionvid: info: ionvideo open
- [ 20.384556@4] ionvid: info: ionvideo_stop_generating!!!!
- [ 20.384636@4] ionvid: info: ionvideo release
- [ 20.419431@5] codec:vdec_create instance ffffff800772d000, total 1
- [ 20.420213@4] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 2000000 to 115200
- [ 20.420294@5] codec:vdec_release instance ffffff800772d000, total 0
- [ 20.420545@5] codec:vdec_create instance ffffff8007740000, total 1
- [ 20.420589@5] codec:vdec_release instance ffffff8007740000, total 0
- [ 20.420766@5] ionvid: info: ionvideo open
- [ 20.554519@3] wifi_platform_bus_enumerate device present 1
- [ 20.554555@3] ======== Card detection to detect SDIO card! ========
- [ 20.560588@3] sdio_reset_comm():
- [ 20.568246@4] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 20.572186@4] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 20.578835@4] sdio: Error resetting SDIO communications (-22)
- [ 20.584153@4] [sdio_reinit] finish
- [ 20.614502@7] ionvid: info: ionvideo_stop_generating!!!!
- [ 20.614575@7] ionvid: info: ionvideo release
- [ 20.626319@7] codec:vdec_create instance ffffff800778f000, total 1
- [ 20.627145@7] codec:vdec_release instance ffffff800778f000, total 0
- [ 20.633478@7] codec:vdec_create instance ffffff80077a2000, total 1
- [ 20.639461@7] codec:vdec_release instance ffffff80077a2000, total 0
- [ 20.645763@7] ionvid: info: ionvideo open
- [ 20.656688@7] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 115200 to 2000000
- [ 20.660564@3] .gms.persistent[4856]: syscall 278
- [ 20.664237@3] Code: aa0403e3 aa0503e4 aa0603e5 d4000001 (b140041f)
- [ 20.670519@3] CPU: 3 PID: 4856 Comm: .gms.persistent Tainted: G O 3.14.29-g069ad3a8 #7
- [ 20.679161@3] task: ffffffc08c2cf000 ti: ffffffc09c4c0000 task.ti: ffffffc09c4c0000
- [ 20.686792@3] PC is at 0x7ce1242cf0
- [ 20.690211@3] LR is at 0x7cd5fd1d10
- [ 20.693640@3] pc : [<0000007ce1242cf0>] lr : [<0000007cd5fd1d10>] pstate: 20000000
- [ 20.701187@3] sp : 0000007ffb9daf10
- [ 20.704668@3] x29: 0000007ffb9dafa0 x28: 0000000000000001
- [ 20.710019@3] x27: 6b7ccd021f30c45e x26: 0000007cde095a98
- [ 20.715450@3] x25: 6b7ccd021f30c45e x24: 0000000000000004
- [ 20.720887@3] x23: 0000007ce2008b30 x22: 0000000000000000
- [ 20.726320@3] x21: 0000007ffb9daf4c x20: 0000000000000001
- [ 20.731749@3] x19: 0000000000000001 x18: 0000007cc0334118
- [ 20.737183@3] x17: 0000007ce1242cd0 x16: 0000007cd5fedee0
- [ 20.742626@3] x15: 0000000000000000 x14: 0000007cddaae804
- [ 20.748051@3] x13: 0000007cddaae7a4 x12: 0000007cde00c608
- [ 20.753488@3] x11: 0000000000000000 x10: 0000000000000001
- [ 20.758921@3] x9 : 0000000000000000 x8 : 0000000000000116
- [ 20.764355@3] x7 : 0000000000000000 x6 : 0000000000000000
- [ 20.769787@3] x5 : 0000000000000000 x4 : 0000000000000000
- [ 20.775227@3] x3 : 0000000000000000 x2 : 0000000000000001
- [ 20.780662@3] x1 : 0000000000000001 x0 : 0000007ffb9daf4c
- [ 20.786085@3]
- [ 20.844531@7] ionvid: info: ionvideo_stop_generating!!!!
- [ 20.844723@7] ionvid: info: ionvideo release
- [ 20.876878@4] codec:vdec_create instance ffffff80077d1000, total 1
- [ 20.877988@4] codec:vdec_release instance ffffff80077d1000, total 0
- [ 20.884084@4] codec:vdec_create instance ffffff80077e4000, total 1
- [ 20.890311@1] codec:vdec_release instance ffffff80077e4000, total 0
- [ 20.898294@1] ionvid: info: ionvideo open
- [ 21.094491@1] ionvid: info: ionvideo_stop_generating!!!!
- [ 21.094557@1] ionvid: info: ionvideo release
- [ 22.584491@2] failed to power up DHD generic adapter, 3 retry left
- [ 22.601520@5] wifi_platform_set_power = 0
- [ 22.601554@5] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 22.605135@5] wifi_platform_bus_enumerate device present 0
- [ 22.610519@5] ======== Card detection to remove SDIO card! ========
- [ 22.616799@5] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 22.823672@2] wifi_platform_set_power = 1
- [ 22.823725@2] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 22.827397@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 23.034268@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 23.544498@2] wifi_platform_bus_enumerate device present 1
- [ 23.544533@2] ======== Card detection to detect SDIO card! ========
- [ 23.550555@2] sdio_reset_comm():
- [ 23.557957@7] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 23.665671@7] sdio: queuing unknown CIS tuple 0x80 (150 bytes)
- [ 23.704016@7] sdio: queuing unknown CIS tuple 0x48 (68 bytes)
- [ 23.707106@7] sdio: clk 200000000 SDR mode tuning start
- [ 23.709678@4] sdio: rx_tuning_result[1] = 10
- [ 23.713894@4] sdio: rx_tuning_result[2] = 10
- [ 23.718130@4] sdio: rx_tuning_result[3] = 10
- [ 23.722269@4] sdio: rx_tuning_result[4] = 10
- [ 23.726300@4] sdio: best_win_start =1, best_win_size =4
- [ 23.731692@4] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x32000
- [ 23.738779@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x32000
- [ 23.744886@1] [sdio_reinit] finish
- [ 24.458395@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
- [ 24.459020@3] audio_dsp: last mode 0,now 0
- [ 24.466899@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
- [ 24.469286@4] audio_dsp: last mode 0,now 0
- [ 25.204659@1] type=1400 audit(1293883431.230:44): avc: denied { getattr } for pid=5183 comm="bootstat" path="/vendor" dev="rootfs" ino=2076 scontext=u:r:bootstat:s0 tcontext=u:ob
- ject_r:rootfs:s0 tclass=lnk_file permissive=1
- [ 25.270767@5] type=1400 audit(1293883431.300:45): avc: denied { getattr } for pid=5199 comm="preinstall.sh" path="/data/local/symbol_thirdpart_apks_installed" dev="mmcblk0p13" in
- o=979203 scontext=u:r:preinstall:s0 tcontext=u:object_r:system_data_file:s0 tclass=file permissive=1
- [ 25.744545@1] failed to power up DHD generic adapter, 2 retry left
- [ 25.761795@7] wifi_platform_set_power = 0
- [ 25.761830@7] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 25.765496@7] wifi_platform_bus_enumerate device present 0
- [ 25.771037@7] ======== Card detection to remove SDIO card! ========
- [ 25.777712@7] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 25.969722@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
- [ 25.969780@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
- [ 25.995595@3] wifi_platform_set_power = 1
- [ 25.995630@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 25.999276@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 26.012778@4] dig: isBootCompleted:1!
- [ 26.014084@4] dig: setDataRoCount count:0!
- [ 26.026028@1] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
- [ 26.031021@1] hub 1-0:1.0: USB hub found
- [ 26.031110@1] hub 1-0:1.0: 3 ports detected
- [ 26.034898@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
- [ 26.040584@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
- [ 26.053218@2] hub 2-0:1.0: USB hub found
- [ 26.053312@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
- [ 26.089188@0] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0
- [ 26.192530@0] dwc_otg: Core Release: 3.10a
- [ 26.192564@0] dwc_otg: Setting default values for core params
- [ 26.196774@0] dwc_otg: curmode: 0, host_only: 0
- [ 26.207942@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 26.213584@0] dwc_otg: Using Buffer DMA mode
- [ 26.213641@0] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
- [ 26.218757@0] dwc_otg: Working on port type = SLAVE
- [ 26.223587@0] dwc_otg: Dedicated Tx FIFOs mode
- [ 26.247516@1] Number of LUNs=8
- [ 26.247559@1] Mass Storage Function, version: 2009/09/11
- [ 26.250220@1] LUN: removable file: (no medium)
- [ 26.256117@1] android_usb gadget: android_usb ready
- [ 26.261979@1] file system registered
- [ 26.266225@1] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
- [ 26.272683@1] init: write: cannot expand '${ro.usb.vendor.string}'
- [ 26.278955@1] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
- [ 26.288945@1] init: write: cannot expand '${ro.usb.product.string}'
- [ 26.299013@1] init: finit_module for "/system/lib/dwc3.ko" failed: File existsinit: finit_module for "/system/lib/dwc_otg.ko" failed: File exists
- [ 26.317408@1] ffs_data_put(): freeing
- [ 26.318307@1] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
- [ 26.319628@0] read descriptors
- [ 26.319641@0] read descriptors
- [ 26.319652@0] read strings
- [ 26.335443@1] init: write: cannot expand '${ro.usb.vendor.string}'
- [ 26.342234@1] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
- [ 26.358672@0] init: write: cannot expand '${ro.usb.product.string}'
- [ 26.368131@0] init: finit_module for "/system/lib/dwc3.ko" failed: File exists
- [ 26.375070@5] usb 1-1: new high-speed USB device number 2 using xhci-hcd
- [ 26.384405@5] init: finit_module for "/system/lib/dwc_otg.ko" failed: File exists
- [ 26.398293@2] ffs_data_put(): freeing
- [ 26.398985@2] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
- [ 26.406306@2] init: write: cannot expand '${ro.usb.vendor.string}'
- [ 26.412390@2] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
- [ 26.422337@2] init: write: cannot expand '${ro.usb.product.string}'
- [ 26.430342@2] android_usb: already disabled
- [ 26.443950@2] read descriptors
- [ 26.444005@2] read descriptors
- [ 26.444434@2] read strings
- [ 26.530509@4] hub 1-1:1.0: USB hub found
- [ 26.530767@4] hub 1-1:1.0: 4 ports detected
- [ 26.588427@5] gle.android.gms[5341]: syscall 278
- [ 26.588488@5] Code: aa0403e3 aa0503e4 aa0603e5 d4000001 (b140041f)
- [ 26.593678@5] CPU: 5 PID: 5341 Comm: gle.android.gms Tainted: G O 3.14.29-g069ad3a8 #7
- [ 26.602543@3] task: ffffffc0978e2000 ti: ffffffc097920000 task.ti: ffffffc097920000
- [ 26.610097@3] PC is at 0x7ce1242cf0
- [ 26.613400@3] LR is at 0x7cd5fd1d10
- [ 26.616920@3] pc : [<0000007ce1242cf0>] lr : [<0000007cd5fd1d10>] pstate: 20000000
- [ 26.624366@3] sp : 0000007ffb9d98f0
- [ 26.627889@3] x29: 0000007ffb9d9980 x28: 0000000000000001
- [ 26.633230@3] x27: 6b7ccd021f30c45e x26: 0000007cde095a98
- [ 26.638664@3] x25: 6b7ccd021f30c45e x24: 0000000000000004
- [ 26.644094@3] x23: 0000007ce2008b30 x22: 0000000000000000
- [ 26.649527@3] x21: 0000007ffb9d992c x20: 0000000000000001
- [ 26.654985@3] x19: 0000000000000001 [ 26.655628@6] usb 1-3: new high-speed USB device number 3 using xhci-hcd
- [ 26.665083@3] x18: 0000007cdc9a3118
- [ 26.668674@3] x17: 0000007ce1242cd0 x16: 0000007cd5fedee0
- [ 26.674120@3] x15: 0000000000000000 x14: 0000007cddaae804
- [ 26.679544@3] x13: 0000007cddaae7a4 x12: 0000007cde00c608
- [ 26.684977@3] x11: 0000000000000000 x10: 0000000000000001
- [ 26.690435@3] x9 : 0000000000000000 x8 : 0000000000000116
- [ 26.695951@3] x7 : 0000000000000000 x6 : 0000000000000000
- [ 26.701280@3] x5 : 0000000000000000 x4 : 0000000000000000
- [ 26.706716@3] x3 : 0000000000000000 x2 : 0000000000000001
- [ 26.712142@3] x1 : 0000000000000001 x0 : 0000007ffb9d992c
- [ 26.717576@3]
- [ 26.724606@1] wifi_platform_bus_enumerate device present 1
- [ 26.724673@1] ======== Card detection to detect SDIO card! ========
- [ 26.730943@1] sdio_reset_comm():
- [ 26.738347@7] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 26.742718@7] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 26.748863@7] sdio: Error resetting SDIO communications (-22)
- [ 26.754547@7] [sdio_reinit] finish
- [ 26.811770@4] usb-storage 1-3:1.0: USB Mass Storage device detected
- [ 26.814329@5] scsi0 : usb-storage 1-3:1.0
- [ 26.914619@6] usb 1-1.2: new low-speed USB device number 4 using xhci-hcd
- [ 27.040857@4] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
- [ 27.044277@4] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
- [ 27.078504@7] input: HID 0e8f:2517 as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.2/1-1.2:1.0/0003:0E8F:2517.0001/input/input4
- [ 27.086021@7] hid-generic 0003:0E8F:2517.0001: input,hidraw0: USB HID v1.10 Keyboard [HID 0e8f:2517] on usb-xhci-hcd.0.auto-1.2/input0
- [ 27.108358@2] input: HID 0e8f:2517 as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.2/1-1.2:1.1/0003:0E8F:2517.0002/input/input5
- [ 27.117378@2] hid-generic 0003:0E8F:2517.0002: input,hidraw1: USB HID v1.10 Mouse [HID 0e8f:2517] on usb-xhci-hcd.0.auto-1.2/input1
- [ 28.210675@7] scsi 0:0:0:0: Direct-Access JetFlash Transcend 64GB 1100 PQ: 0 ANSI: 6
- [ 28.218484@6] sd 0:0:0:0: [sda] 123404288 512-byte logical blocks: (63.1 GB/58.8 GiB)
- [ 28.221769@6] sd 0:0:0:0: [sda] Write Protect is off
- [ 28.227375@7] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- [ 28.241481@5] sda: sda1
- [ 28.256179@4] sd 0:0:0:0: [sda] Attached SCSI removable disk
- [ 28.754541@3] failed to power up DHD generic adapter, 1 retry left
- [ 28.771514@6] wifi_platform_set_power = 0
- [ 28.771553@6] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 28.775131@6] wifi_platform_bus_enumerate device present 0
- [ 28.780523@6] ======== Card detection to remove SDIO card! ========
- [ 28.786809@6] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 28.993739@1] wifi_platform_set_power = 1
- [ 28.993772@1] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 28.997455@1] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 29.067178@4] audio_dsp: drc high cut scale set to 100%
- [ 29.067714@4] audio_dsp: drc low boost scale set to 100%
- [ 29.072596@4] audio_dsp: drc mode set to LINE
- [ 29.204628@1] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 29.714513@3] wifi_platform_bus_enumerate device present 1
- [ 29.714549@3] ======== Card detection to detect SDIO card! ========
- [ 29.720591@3] sdio_reset_comm():
- [ 29.727977@4] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 29.732168@4] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 29.738582@4] sdio: Error resetting SDIO communications (-22)
- [ 29.744129@4] [sdio_reinit] finish
- [ 29.896335@7] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
- [ 31.744538@1] failed to power up DHD generic adapter, 0 retry left
- [ 31.762157@7] wifi_platform_set_power = 0
- [ 31.762198@7] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 31.765850@7] wifi_platform_bus_enumerate device present 0
- [ 31.771448@7] ======== Card detection to remove SDIO card! ========
- [ 31.777659@7] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 31.985154@2] failed to power up DHD generic adapter, max retry reached**
- [ 31.986336@2] unregister wifi platform drivers
- [ 31.990716@2] wifi_platform_bus_enumerate device present 0
- [ 31.996229@2] ======== Card detection to remove SDIO card! ========
- [ 32.002370@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 32.209333@2] ======== dhd_wlan_deinit_plat_data ========
- [ 32.209373@2] dhd_module_init: Failed to load the driver, try cnt 3
- [ 32.215365@2] ======== dhd_wlan_init_plat_data ========
- [ 32.220485@2] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
- [ 32.225616@2] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
- [ 32.230922@2] dhd_wlan_init_gpio: host_oob_irq: 100
- [ 32.235801@2] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
- [ 32.241187@2] dhd_wifi_platform_load: Enter
- [ 32.245399@2] Power-up adapter 'DHD generic adapter'
- [ 32.250252@2] wifi_platform_set_power = 1
- [ 32.254204@2] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 32.259573@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 32.466471@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 32.974528@2] wifi_platform_bus_enumerate device present 1
- [ 32.974564@2] ======== Card detection to detect SDIO card! ========
- [ 32.980587@2] sdio_reset_comm():
- [ 32.988046@7] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 33.112475@4] sdio: queuing unknown CIS tuple 0x80 (150 bytes)
- [ 33.153929@6] sdio: queuing unknown CIS tuple 0x48 (68 bytes)
- [ 33.157219@4] sdio: clk 200000000 SDR mode tuning start
- [ 33.159729@7] sdio: rx_tuning_result[1] = 10
- [ 33.163844@7] sdio: rx_tuning_result[2] = 10
- [ 33.168232@7] sdio: rx_tuning_result[3] = 10
- [ 33.173004@0] sdio: rx_tuning_result[4] = 10
- [ 33.176230@0] sdio: best_win_start =1, best_win_size =4
- [ 33.181350@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x32000
- [ 33.188828@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x32000
- [ 33.194912@0] [sdio_reinit] finish
- [ 33.996018@3] binder: 4856: binder_alloc_buf size 1056768 failed, no address space
- [ 33.997946@3] binder: 5341:5517 transaction failed 29201, size 1056768-0
- [ 35.194515@0] failed to power up DHD generic adapter, 3 retry left
- [ 35.212018@4] wifi_platform_set_power = 0
- [ 35.212055@4] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 35.215770@4] wifi_platform_bus_enumerate device present 0
- [ 35.221084@4] ======== Card detection to remove SDIO card! ========
- [ 35.228286@4] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 35.435299@0] wifi_platform_set_power = 1
- [ 35.435331@0] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 35.439034@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 35.649087@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 36.154527@1] wifi_platform_bus_enumerate device present 1
- [ 36.154567@1] ======== Card detection to detect SDIO card! ========
- [ 36.160613@1] sdio_reset_comm():
- [ 36.167775@4] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 36.172231@4] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 36.178713@5] sdio: Error resetting SDIO communications (-22)
- [ 36.184377@5] [sdio_reinit] finish
- [ 37.052230@1] id.gms.unstable[6230]: syscall 278
- [ 37.052269@1] Code: aa0403e3 aa0503e4 aa0603e5 d4000001 (b140041f)
- [ 37.057536@1] CPU: 1 PID: 6230 Comm: id.gms.unstable Tainted: G O 3.14.29-g069ad3a8 #7
- [ 37.066241@1] task: ffffffc095639000 ti: ffffffc05c6d4000 task.ti: ffffffc05c6d4000
- [ 37.073753@1] PC is at 0x7ce1242cf0
- [ 37.077263@1] LR is at 0x7cd5fd1d10
- [ 37.080631@1] pc : [<0000007ce1242cf0>] lr : [<0000007cd5fd1d10>] pstate: 20000000
- [ 37.088204@1] sp : 0000007ffb9d98f0
- [ 37.091584@1] x29: 0000007ffb9d9980 x28: 0000000000000001
- [ 37.097015@1] x27: 6b7ccd021f30c45e x26: 0000007cde095a98
- [ 37.102446@1] x25: 6b7ccd021f30c45e x24: 0000000000000004
- [ 37.107895@1] x23: 0000007ce2008b30 x22: 0000000000000000
- [ 37.113315@1] x21: 0000007ffb9d992c x20: 0000000000000001
- [ 37.118750@1] x19: 0000000000000001 x18: 0000007cdc963118
- [ 37.124184@1] x17: 0000007ce1242cd0 x16: 0000007cd5fedee0
- [ 37.129616@1] x15: 0000000000000000 x14: 0000007cddaae804
- [ 37.135054@1] x13: 0000007cddaae7a4 x12: 0000007cde00c608
- [ 37.140502@1] x11: 0000000000000000 x10: 0000000000000001
- [ 37.145919@1] x9 : 0000000000000000 x8 : 0000000000000116
- [ 37.151350@1] x7 : 0000000000000000 x6 : 0000000000000000
- [ 37.156785@1] x5 : 0000000000000000 x4 : 0000000000000000
- [ 37.162217@1] x3 : 0000000000000000 x2 : 0000000000000001
- [ 37.167654@1] x1 : 0000000000000001 x0 : 0000007ffb9d992c
- [ 37.173085@1]
- [ 37.351650@3] .android.gms.ui[6258]: syscall 278
- [ 37.351688@3] Code: aa0403e3 aa0503e4 aa0603e5 d4000001 (b140041f)
- [ 37.356916@3] CPU: 3 PID: 6258 Comm: .android.gms.ui Tainted: G O 3.14.29-g069ad3a8 #7
- [ 37.365703@3] task: ffffffc05bdc6000 ti: ffffffc05e1e0000 task.ti: ffffffc05e1e0000
- [ 37.373164@3] PC is at 0x7ce1242cf0
- [ 37.376687@3] LR is at 0x7cd5fd1d10
- [ 37.380057@3] pc : [<0000007ce1242cf0>] lr : [<0000007cd5fd1d10>] pstate: 20000000
- [ 37.387620@3] sp : 0000007ffb9d98f0
- [ 37.391008@3] x29: 0000007ffb9d9980 x28: 0000000000000001
- [ 37.396440@3] x27: 6b7ccd021f30c45e x26: 0000007cde095a98
- [ 37.401870@3] x25: 6b7ccd021f30c45e x24: 0000000000000004
- [ 37.407307@3] x23: 0000007ce2008b30 x22: 0000000000000000
- [ 37.412738@3] x21: 0000007ffb9d992c x20: 0000000000000001
- [ 37.418173@3] x19: 0000000000000001 x18: 0000007cdc9a3118
- [ 37.423606@3] x17: 0000007ce1242cd0 x16: 0000007cd5fedee0
- [ 37.429041@3] x15: 0000000000000000 x14: 0000007cddaae804
- [ 37.434496@3] x13: 0000007cddaae7a4 x12: 0000007cde00c608
- [ 37.439907@3] x11: 0000000000000000 x10: 0000000000000001
- [ 37.445343@3] x9 : 0000000000000000 x8 : 0000000000000116
- [ 37.450775@3] x7 : 0000000000000000 x6 : 0000000000000000
- [ 37.456212@3] x5 : 0000000000000000 x4 : 0000000000000000
- [ 37.461649@3] x3 : 0000000000000000 x2 : 0000000000000001
- [ 37.467083@3] x1 : 0000000000000001 x0 : 0000007ffb9d992c
- [ 37.472511@3]
- [ 38.184512@2] failed to power up DHD generic adapter, 2 retry left
- [ 38.201976@7] wifi_platform_set_power = 0
- [ 38.202016@7] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 38.205761@7] wifi_platform_bus_enumerate device present 0
- [ 38.210975@7] ======== Card detection to remove SDIO card! ========
- [ 38.219424@7] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 38.424114@3] wifi_platform_set_power = 1
- [ 38.424148@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 38.427864@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 38.634870@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 39.144513@3] wifi_platform_bus_enumerate device present 1
- [ 39.144550@3] ======== Card detection to detect SDIO card! ========
- [ 39.150592@3] sdio_reset_comm():
- [ 39.158967@6] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 39.162164@6] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 39.168752@6] sdio: Error resetting SDIO communications (-22)
- [ 39.174127@6] [sdio_reinit] finish
- [ 41.174517@0] failed to power up DHD generic adapter, 1 retry left
- [ 41.191522@5] wifi_platform_set_power = 0
- [ 41.191559@5] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 41.195123@5] wifi_platform_bus_enumerate device present 0
- [ 41.200516@5] ======== Card detection to remove SDIO card! ========
- [ 41.206778@5] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 41.413653@1] wifi_platform_set_power = 1
- [ 41.413684@1] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 41.417368@1] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 41.624257@1] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 42.134506@1] wifi_platform_bus_enumerate device present 1
- [ 42.134540@1] ======== Card detection to detect SDIO card! ========
- [ 42.140568@1] sdio_reset_comm():
- [ 42.148008@4] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 42.258736@7] sdio: queuing unknown CIS tuple 0x80 (150 bytes)
- [ 42.297318@5] sdio: queuing unknown CIS tuple 0x48 (68 bytes)
- [ 42.300288@5] sdio: clk 200000000 SDR mode tuning start
- [ 42.302922@5] sdio: rx_tuning_result[1] = 10
- [ 42.307235@7] sdio: rx_tuning_result[2] = 10
- [ 42.311344@7] sdio: rx_tuning_result[3] = 10
- [ 42.315769@7] sdio: rx_tuning_result[4] = 10
- [ 42.319509@7] sdio: best_win_start =1, best_win_size =4
- [ 42.324737@7] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x32000
- [ 42.332073@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x32000
- [ 42.338207@2] [sdio_reinit] finish
- [ 44.334528@2] failed to power up DHD generic adapter, 0 retry left
- [ 44.351603@6] wifi_platform_set_power = 0
- [ 44.351637@6] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 44.355353@6] wifi_platform_bus_enumerate device present 0
- [ 44.360637@6] ======== Card detection to remove SDIO card! ========
- [ 44.367100@6] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 44.573906@3] failed to power up DHD generic adapter, max retry reached**
- [ 44.575199@3] unregister wifi platform drivers
- [ 44.579457@3] wifi_platform_bus_enumerate device present 0
- [ 44.584911@3] ======== Card detection to remove SDIO card! ========
- [ 44.591115@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 44.798063@3] ======== dhd_wlan_deinit_plat_data ========
- [ 44.798102@3] dhd_module_init: Failed to load the driver, try cnt 2
- [ 44.804054@3] ======== dhd_wlan_init_plat_data ========
- [ 44.809248@3] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
- [ 44.814304@3] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
- [ 44.819692@3] dhd_wlan_init_gpio: host_oob_irq: 100
- [ 44.824566@3] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
- [ 44.829916@3] dhd_wifi_platform_load: Enter
- [ 44.834073@3] Power-up adapter 'DHD generic adapter'
- [ 44.839035@3] wifi_platform_set_power = 1
- [ 44.842939@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 44.848255@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 45.055189@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 45.564520@3] wifi_platform_bus_enumerate device present 1
- [ 45.564554@3] ======== Card detection to detect SDIO card! ========
- [ 45.570577@3] sdio_reset_comm():
- [ 45.577558@6] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 45.693661@6] sdio: queuing unknown CIS tuple 0x80 (150 bytes)
- [ 45.732134@6] sdio: queuing unknown CIS tuple 0x48 (68 bytes)
- [ 45.735227@5] sdio: clk 200000000 SDR mode tuning start
- [ 45.737758@5] sdio: rx_tuning_result[1] = 10
- [ 45.741977@6] sdio: rx_tuning_result[2] = 10
- [ 45.746251@6] sdio: rx_tuning_result[3] = 10
- [ 45.750398@6] sdio: rx_tuning_result[4] = 10
- [ 45.754327@6] sdio: best_win_start =1, best_win_size =4
- [ 45.759614@6] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x32000
- [ 45.766917@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x32000
- [ 45.772964@2] [sdio_reinit] finish
- [ 47.774508@2] failed to power up DHD generic adapter, 3 retry left
- [ 47.791656@4] wifi_platform_set_power = 0
- [ 47.791691@4] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 47.795285@4] wifi_platform_bus_enumerate device present 0
- [ 47.800650@4] ======== Card detection to remove SDIO card! ========
- [ 47.806929@4] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 48.013828@0] wifi_platform_set_power = 1
- [ 48.013860@0] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 48.017580@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 48.224542@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 48.734527@0] wifi_platform_bus_enumerate device present 1
- [ 48.734566@0] ======== Card detection to detect SDIO card! ========
- [ 48.740659@0] sdio_reset_comm():
- [ 48.747586@5] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 48.752158@5] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 48.758547@5] sdio: Error resetting SDIO communications (-22)
- [ 48.764144@5] [sdio_reinit] finish
- [ 50.764496@2] failed to power up DHD generic adapter, 2 retry left
- [ 50.781553@6] wifi_platform_set_power = 0
- [ 50.781588@6] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 50.785184@6] wifi_platform_bus_enumerate device present 0
- [ 50.790551@6] ======== Card detection to remove SDIO card! ========
- [ 50.796823@6] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 51.003683@0] wifi_platform_set_power = 1
- [ 51.003714@0] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 51.007482@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 51.214329@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 51.724546@0] wifi_platform_bus_enumerate device present 1
- [ 51.724582@0] ======== Card detection to detect SDIO card! ========
- [ 51.730602@0] sdio_reset_comm():
- [ 51.738030@6] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 51.848402@7] sdio: queuing unknown CIS tuple 0x80 (150 bytes)
- [ 51.886559@7] sdio: queuing unknown CIS tuple 0x48 (68 bytes)
- [ 51.889523@7] sdio: clk 200000000 SDR mode tuning start
- [ 51.892165@7] sdio: rx_tuning_result[1] = 10
- [ 51.896425@7] sdio: rx_tuning_result[2] = 10
- [ 51.900630@4] sdio: rx_tuning_result[3] = 10
- [ 51.905021@4] sdio: rx_tuning_result[4] = 10
- [ 51.908758@4] sdio: best_win_start =1, best_win_size =4
- [ 51.913930@4] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x32000
- [ 51.921315@4] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x32000
- [ 51.927459@4] [sdio_reinit] finish
- [ 53.924519@3] failed to power up DHD generic adapter, 1 retry left
- [ 53.941542@5] wifi_platform_set_power = 0
- [ 53.941580@5] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 53.945170@5] wifi_platform_bus_enumerate device present 0
- [ 53.950543@5] ======== Card detection to remove SDIO card! ========
- [ 53.956832@5] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 54.163821@3] wifi_platform_set_power = 1
- [ 54.163850@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 54.167539@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 54.374406@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 54.884583@3] wifi_platform_bus_enumerate device present 1
- [ 54.884618@3] ======== Card detection to detect SDIO card! ========
- [ 54.890639@3] sdio_reset_comm():
- [ 54.897606@7] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 54.902205@7] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 54.908577@7] sdio: Error resetting SDIO communications (-22)
- [ 54.914189@7] [sdio_reinit] finish
- [ 56.914526@1] failed to power up DHD generic adapter, 0 retry left
- [ 56.931581@6] wifi_platform_set_power = 0
- [ 56.931615@6] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 56.935204@6] wifi_platform_bus_enumerate device present 0
- [ 56.940581@6] ======== Card detection to remove SDIO card! ========
- [ 56.946877@6] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 57.153711@0] failed to power up DHD generic adapter, max retry reached**
- [ 57.154947@0] unregister wifi platform drivers
- [ 57.159316@0] wifi_platform_bus_enumerate device present 0
- [ 57.164733@0] ======== Card detection to remove SDIO card! ========
- [ 57.170922@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 57.377933@0] ======== dhd_wlan_deinit_plat_data ========
- [ 57.377973@0] dhd_module_init: Failed to load the driver, try cnt 1
- [ 57.383927@0] ======== dhd_wlan_init_plat_data ========
- [ 57.389189@0] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
- [ 57.394179@0] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
- [ 57.399614@0] dhd_wlan_init_gpio: host_oob_irq: 100
- [ 57.404356@0] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
- [ 57.409874@0] dhd_wifi_platform_load: Enter
- [ 57.413952@0] Power-up adapter 'DHD generic adapter'
- [ 57.418901@0] wifi_platform_set_power = 1
- [ 57.422864@0] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 57.428182@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 57.635253@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 58.144531@1] wifi_platform_bus_enumerate device present 1
- [ 58.144567@1] ======== Card detection to detect SDIO card! ========
- [ 58.150587@1] sdio_reset_comm():
- [ 58.158083@6] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 58.162163@6] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 58.168522@6] sdio: Error resetting SDIO communications (-22)
- [ 58.174138@6] [sdio_reinit] finish
- [ 60.174528@3] failed to power up DHD generic adapter, 3 retry left
- [ 60.191805@6] wifi_platform_set_power = 0
- [ 60.191839@6] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 60.195456@6] wifi_platform_bus_enumerate device present 0
- [ 60.200804@6] ======== Card detection to remove SDIO card! ========
- [ 60.207253@6] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 60.413938@3] wifi_platform_set_power = 1
- [ 60.413967@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 60.417644@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 60.624824@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 61.134525@0] wifi_platform_bus_enumerate device present 1
- [ 61.134561@0] ======== Card detection to detect SDIO card! ========
- [ 61.140643@0] sdio_reset_comm():
- [ 61.147981@4] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 61.152144@4] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 61.158475@4] sdio: Error resetting SDIO communications (-22)
- [ 61.164130@4] [sdio_reinit] finish
- [ 63.164923@3] failed to power up DHD generic adapter, 2 retry left
- [ 63.183081@6] wifi_platform_set_power = 0
- [ 63.183130@6] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 63.186754@6] wifi_platform_bus_enumerate device present 0
- [ 63.192081@6] ======== Card detection to remove SDIO card! ========
- [ 63.198366@6] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 63.405254@3] wifi_platform_set_power = 1
- [ 63.405283@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 63.408908@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 63.615833@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 64.124784@3] wifi_platform_bus_enumerate device present 1
- [ 64.124958@3] ======== Card detection to detect SDIO card! ========
- [ 64.130922@3] sdio_reset_comm():
- [ 64.139084@7] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 64.142468@7] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 64.148827@7] sdio: Error resetting SDIO communications (-22)
- [ 64.154443@7] [sdio_reinit] finish
- [ 66.154484@7] failed to power up DHD generic adapter, 1 retry left
- [ 66.171624@7] wifi_platform_set_power = 0
- [ 66.171661@7] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 66.175213@7] wifi_platform_bus_enumerate device present 0
- [ 66.180616@7] ======== Card detection to remove SDIO card! ========
- [ 66.186889@7] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 66.393784@3] wifi_platform_set_power = 1
- [ 66.393814@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 66.397454@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 66.604355@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 67.114712@3] wifi_platform_bus_enumerate device present 1
- [ 67.114887@3] ======== Card detection to detect SDIO card! ========
- [ 67.120847@3] sdio_reset_comm():
- [ 67.128683@6] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 67.239122@7] sdio: queuing unknown CIS tuple 0x80 (150 bytes)
- [ 67.278343@7] sdio: queuing unknown CIS tuple 0x48 (68 bytes)
- [ 67.281415@7] sdio: clk 200000000 SDR mode tuning start
- [ 67.284429@7] sdio: rx_tuning_result[1] = 10
- [ 67.288833@7] sdio: rx_tuning_result[2] = 10
- [ 67.292755@7] sdio: rx_tuning_result[3] = 10
- [ 67.297066@7] sdio: rx_tuning_result[4] = 10
- [ 67.300539@7] sdio: best_win_start =1, best_win_size =4
- [ 67.305731@7] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x32000
- [ 67.313054@7] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x32000
- [ 67.319191@7] [sdio_reinit] finish
- [ 69.314738@0] failed to power up DHD generic adapter, 0 retry left
- [ 69.333366@4] wifi_platform_set_power = 0
- [ 69.333437@4] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 69.337026@4] wifi_platform_bus_enumerate device present 0
- [ 69.342382@4] ======== Card detection to remove SDIO card! ========
- [ 69.348710@4] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 69.555634@2] failed to power up DHD generic adapter, max retry reached**
- [ 69.556811@2] unregister wifi platform drivers
- [ 69.561175@2] wifi_platform_bus_enumerate device present 0
- [ 69.566638@2] ======== Card detection to remove SDIO card! ========
- [ 69.572835@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 69.779749@2] ======== dhd_wlan_deinit_plat_data ========
- [ 69.779788@2] dhd_module_init: Failed to load the driver, try cnt 0
- [ 69.785763@2] dhd_module_init: Failed to load driver max retry reached**
- [ 69.792362@2] dhd_module_init: Exit err=-19
- [ 69.857614@3] dhd_module_init: in Dongle Host Driver, version 1.363.59.144.9 (r)
- [ 69.859381@3] ======== dhd_wlan_init_plat_data ========
- [ 69.864566@3] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
- [ 69.869623@3] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
- [ 69.874991@3] dhd_wlan_init_gpio: host_oob_irq: 100
- [ 69.879800@3] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
- [ 69.885317@3] dhd_wifi_platform_load: Enter
- [ 69.889394@3] Power-up adapter 'DHD generic adapter'
- [ 69.894289@3] wifi_platform_set_power = 1
- [ 69.898275@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 69.903534@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 70.110492@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 70.614701@3] wifi_platform_bus_enumerate device present 1
- [ 70.614869@3] ======== Card detection to detect SDIO card! ========
- [ 70.620845@3] sdio_reset_comm():
- [ 70.628190@5] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 70.632381@5] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 70.638906@5] sdio: Error resetting SDIO communications (-22)
- [ 70.644397@5] [sdio_reinit] finish
- [ 72.644531@5] failed to power up DHD generic adapter, 3 retry left
- [ 72.662340@5] wifi_platform_set_power = 0
- [ 72.662389@5] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 72.665954@5] wifi_platform_bus_enumerate device present 0
- [ 72.671343@5] ======== Card detection to remove SDIO card! ========
- [ 72.677618@5] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 72.884739@3] wifi_platform_set_power = 1
- [ 72.884773@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 72.888396@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 73.095337@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 73.604704@3] wifi_platform_bus_enumerate device present 1
- [ 73.604882@3] ======== Card detection to detect SDIO card! ========
- [ 73.610839@3] sdio_reset_comm():
- [ 73.618895@5] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 73.622385@5] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 73.628772@5] sdio: Error resetting SDIO communications (-22)
- [ 73.634361@5] [sdio_reinit] finish
- [ 75.634514@5] failed to power up DHD generic adapter, 2 retry left
- [ 75.652295@5] wifi_platform_set_power = 0
- [ 75.652348@5] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 75.655906@5] wifi_platform_bus_enumerate device present 0
- [ 75.661293@5] ======== Card detection to remove SDIO card! ========
- [ 75.667590@5] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 75.874508@0] wifi_platform_set_power = 1
- [ 75.874541@0] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 75.878166@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 76.085179@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 76.594864@0] wifi_platform_bus_enumerate device present 1
- [ 76.595036@0] ======== Card detection to detect SDIO card! ========
- [ 76.600997@0] sdio_reset_comm():
- [ 76.608758@5] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 76.612542@5] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 76.618881@5] sdio: Error resetting SDIO communications (-22)
- [ 76.624552@5] [sdio_reinit] finish
- [ 78.624646@5] failed to power up DHD generic adapter, 1 retry left
- [ 78.642225@5] wifi_platform_set_power = 0
- [ 78.642272@5] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 78.645840@5] wifi_platform_bus_enumerate device present 0
- [ 78.651229@5] ======== Card detection to remove SDIO card! ========
- [ 78.657554@5] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 78.864382@0] wifi_platform_set_power = 1
- [ 78.864415@0] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 78.868054@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 79.075004@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 79.584503@0] wifi_platform_bus_enumerate device present 1
- [ 79.584541@0] ======== Card detection to detect SDIO card! ========
- [ 79.590628@0] sdio_reset_comm():
- [ 79.597961@5] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 79.602132@5] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 79.608457@5] sdio: Error resetting SDIO communications (-22)
- [ 79.614117@5] [sdio_reinit] finish
- [ 81.615121@2] failed to power up DHD generic adapter, 0 retry left
- [ 81.633051@6] wifi_platform_set_power = 0
- [ 81.633101@6] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 81.636676@6] wifi_platform_bus_enumerate device present 0
- [ 81.642052@6] ======== Card detection to remove SDIO card! ========
- [ 81.648325@6] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 81.855235@2] failed to power up DHD generic adapter, max retry reached**
- [ 81.856417@2] unregister wifi platform drivers
- [ 81.860778@2] wifi_platform_bus_enumerate device present 0
- [ 81.866239@2] ======== Card detection to remove SDIO card! ========
- [ 81.872438@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 82.079352@2] ======== dhd_wlan_deinit_plat_data ========
- [ 82.079393@2] dhd_module_init: Failed to load the driver, try cnt 3
- [ 82.085372@2] ======== dhd_wlan_init_plat_data ========
- [ 82.090500@2] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
- [ 82.095598@2] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
- [ 82.100934@2] dhd_wlan_init_gpio: host_oob_irq: 100
- [ 82.105772@2] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
- [ 82.111197@2] dhd_wifi_platform_load: Enter
- [ 82.115372@2] Power-up adapter 'DHD generic adapter'
- [ 82.120254@2] wifi_platform_set_power = 1
- [ 82.124220@2] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 82.129505@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 82.336433@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 82.844803@2] wifi_platform_bus_enumerate device present 1
- [ 82.844976@2] ======== Card detection to detect SDIO card! ========
- [ 82.850939@2] sdio_reset_comm():
- [ 82.858643@5] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 82.862482@5] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 82.868828@5] sdio: Error resetting SDIO communications (-22)
- [ 82.874488@5] [sdio_reinit] finish
- [ 84.874520@5] failed to power up DHD generic adapter, 3 retry left
- [ 84.892559@5] wifi_platform_set_power = 0
- [ 84.892611@5] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 84.896176@5] wifi_platform_bus_enumerate device present 0
- [ 84.901561@5] ======== Card detection to remove SDIO card! ========
- [ 84.907841@5] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 85.114900@0] wifi_platform_set_power = 1
- [ 85.114933@0] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 85.118559@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 85.325536@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 85.834893@0] wifi_platform_bus_enumerate device present 1
- [ 85.835066@0] ======== Card detection to detect SDIO card! ========
- [ 85.841309@0] sdio_reset_comm():
- [ 85.849093@5] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 85.852576@5] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 85.858927@5] sdio: Error resetting SDIO communications (-22)
- [ 85.864633@5] [sdio_reinit] finish
- [ 87.864651@5] failed to power up DHD generic adapter, 2 retry left
- [ 87.882309@5] wifi_platform_set_power = 0
- [ 87.882363@5] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 87.885929@5] wifi_platform_bus_enumerate device present 0
- [ 87.891310@5] ======== Card detection to remove SDIO card! ========
- [ 87.897584@5] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 88.104640@3] wifi_platform_set_power = 1
- [ 88.104673@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 88.108294@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 88.315235@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 88.824793@0] wifi_platform_bus_enumerate device present 1
- [ 88.824968@0] ======== Card detection to detect SDIO card! ========
- [ 88.830928@0] sdio_reset_comm():
- [ 88.838486@6] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 88.947995@7] sdio: queuing unknown CIS tuple 0x80 (150 bytes)
- [ 88.987183@7] sdio: queuing unknown CIS tuple 0x48 (68 bytes)
- [ 88.990239@7] sdio: clk 200000000 SDR mode tuning start
- [ 88.993266@7] sdio: rx_tuning_result[1] = 10
- [ 88.997459@7] sdio: rx_tuning_result[2] = 10
- [ 89.001580@7] sdio: rx_tuning_result[3] = 10
- [ 89.006055@7] sdio: rx_tuning_result[4] = 10
- [ 89.009371@7] sdio: best_win_start =1, best_win_size =4
- [ 89.014584@7] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x32000
- [ 89.022180@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x32000
- [ 89.028482@0] [sdio_reinit] finish
- [ 91.024885@0] failed to power up DHD generic adapter, 1 retry left
- [ 91.042806@5] wifi_platform_set_power = 0
- [ 91.042856@5] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 91.046578@5] wifi_platform_bus_enumerate device present 0
- [ 91.051817@5] ======== Card detection to remove SDIO card! ========
- [ 91.058101@5] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 91.265026@3] wifi_platform_set_power = 1
- [ 91.265059@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 91.268685@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 91.475815@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 91.984491@0] wifi_platform_bus_enumerate device present 1
- [ 91.984525@0] ======== Card detection to detect SDIO card! ========
- [ 91.990920@0] sdio_reset_comm():
- [ 91.998317@7] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 92.105832@7] sdio: queuing unknown CIS tuple 0x80 (150 bytes)
- [ 92.143261@7] sdio: queuing unknown CIS tuple 0x48 (68 bytes)
- [ 92.146193@7] sdio: clk 200000000 SDR mode tuning start
- [ 92.149972@7] sdio: rx_tuning_result[1] = 10
- [ 92.153089@7] sdio: rx_tuning_result[2] = 10
- [ 92.157372@7] sdio: rx_tuning_result[3] = 10
- [ 92.161534@7] sdio: rx_tuning_result[4] = 10
- [ 92.165485@7] sdio: best_win_start =1, best_win_size =4
- [ 92.170623@7] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x32000
- [ 92.177987@7] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x32000
- [ 92.184091@7] [sdio_reinit] finish
- [ 94.184821@0] failed to power up DHD generic adapter, 0 retry left
- [ 94.202467@4] wifi_platform_set_power = 0
- [ 94.202520@4] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 94.206109@4] wifi_platform_bus_enumerate device present 0
- [ 94.211471@4] ======== Card detection to remove SDIO card! ========
- [ 94.217765@4] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 94.424709@2] failed to power up DHD generic adapter, max retry reached**
- [ 94.425886@2] unregister wifi platform drivers
- [ 94.430250@2] wifi_platform_bus_enumerate device present 0
- [ 94.435721@2] ======== Card detection to remove SDIO card! ========
- [ 94.441918@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 94.648835@2] ======== dhd_wlan_deinit_plat_data ========
- [ 94.648873@2] dhd_module_init: Failed to load the driver, try cnt 2
- [ 94.654844@2] ======== dhd_wlan_init_plat_data ========
- [ 94.659986@2] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
- [ 94.665089@2] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
- [ 94.670422@2] dhd_wlan_init_gpio: host_oob_irq: 100
- [ 94.675263@2] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
- [ 94.680686@2] dhd_wifi_platform_load: Enter
- [ 94.684882@2] Power-up adapter 'DHD generic adapter'
- [ 94.689746@2] wifi_platform_set_power = 1
- [ 94.693709@2] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 94.698994@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 94.905914@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 95.414861@2] wifi_platform_bus_enumerate device present 1
- [ 95.415036@2] ======== Card detection to detect SDIO card! ========
- [ 95.420998@2] sdio_reset_comm():
- [ 95.428282@6] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 95.542250@7] sdio: queuing unknown CIS tuple 0x80 (150 bytes)
- [ 95.581570@6] sdio: queuing unknown CIS tuple 0x48 (68 bytes)
- [ 95.584632@7] sdio: clk 200000000 SDR mode tuning start
- [ 95.587650@7] sdio: rx_tuning_result[1] = 10
- [ 95.591796@7] sdio: rx_tuning_result[2] = 10
- [ 95.596062@7] sdio: rx_tuning_result[3] = 10
- [ 95.600193@7] sdio: rx_tuning_result[4] = 10
- [ 95.603752@7] sdio: best_win_start =1, best_win_size =4
- [ 95.608966@7] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x32000
- [ 95.616489@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x32000
- [ 95.622436@1] [sdio_reinit] finish
- [ 97.625184@2] failed to power up DHD generic adapter, 3 retry left
- [ 97.643114@7] wifi_platform_set_power = 0
- [ 97.643161@7] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 97.646733@7] wifi_platform_bus_enumerate device present 0
- [ 97.652111@7] ======== Card detection to remove SDIO card! ========
- [ 97.658393@7] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 97.865294@2] wifi_platform_set_power = 1
- [ 97.865328@2] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 97.868957@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 98.075893@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 98.584870@2] wifi_platform_bus_enumerate device present 1
- [ 98.585046@2] ======== Card detection to detect SDIO card! ========
- [ 98.591011@2] sdio_reset_comm():
- [ 98.598315@6] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 98.711690@6] sdio: queuing unknown CIS tuple 0x80 (150 bytes)
- [ 98.751496@4] sdio: queuing unknown CIS tuple 0x48 (68 bytes)
- [ 98.754660@7] sdio: clk 200000000 SDR mode tuning start
- [ 98.757597@7] sdio: rx_tuning_result[1] = 10
- [ 98.761675@7] sdio: rx_tuning_result[2] = 10
- [ 98.765955@7] sdio: rx_tuning_result[3] = 10
- [ 98.770126@7] sdio: rx_tuning_result[4] = 10
- [ 98.773689@7] sdio: best_win_start =1, best_win_size =4
- [ 98.778892@7] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x32000
- [ 98.786379@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x32000
- [ 98.792370@3] [sdio_reinit] finish
- [ 100.794661@3] failed to power up DHD generic adapter, 2 retry left
- [ 100.812589@4] wifi_platform_set_power = 0
- [ 100.812649@4] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 100.816425@4] wifi_platform_bus_enumerate device present 0
- [ 100.821596@4] ======== Card detection to remove SDIO card! ========
- [ 100.827893@4] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 101.034786@2] wifi_platform_set_power = 1
- [ 101.034819@2] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 101.038448@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 101.245398@2] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 101.754770@2] wifi_platform_bus_enumerate device present 1
- [ 101.754946@2] ======== Card detection to detect SDIO card! ========
- [ 101.760906@2] sdio_reset_comm():
- [ 101.768736@6] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 101.772461@6] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 101.778947@6] sdio: Error resetting SDIO communications (-22)
- [ 101.784444@6] [sdio_reinit] finish
- [ 103.784507@6] failed to power up DHD generic adapter, 1 retry left
- [ 103.802791@6] wifi_platform_set_power = 0
- [ 103.802845@6] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 103.806405@6] wifi_platform_bus_enumerate device present 0
- [ 103.811793@6] ======== Card detection to remove SDIO card! ========
- [ 103.818138@6] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 104.025037@0] wifi_platform_set_power = 1
- [ 104.025077@0] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 104.028699@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 104.235667@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 104.744952@0] wifi_platform_bus_enumerate device present 1
- [ 104.745126@0] ======== Card detection to detect SDIO card! ========
- [ 104.751092@0] sdio_reset_comm():
- [ 104.758842@7] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 104.762634@7] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 104.769048@7] sdio: Error resetting SDIO communications (-22)
- [ 104.774656@7] [sdio_reinit] finish
- [ 106.774509@7] failed to power up DHD generic adapter, 0 retry left
- [ 106.792494@7] wifi_platform_set_power = 0
- [ 106.792547@7] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 106.796126@7] wifi_platform_bus_enumerate device present 0
- [ 106.801494@7] ======== Card detection to remove SDIO card! ========
- [ 106.807768@7] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 107.014892@3] failed to power up DHD generic adapter, max retry reached**
- [ 107.016074@3] unregister wifi platform drivers
- [ 107.020438@3] wifi_platform_bus_enumerate device present 0
- [ 107.025895@3] ======== Card detection to remove SDIO card! ========
- [ 107.032098@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 107.239059@3] ======== dhd_wlan_deinit_plat_data ========
- [ 107.239101@3] dhd_module_init: Failed to load the driver, try cnt 1
- [ 107.245066@3] ======== dhd_wlan_init_plat_data ========
- [ 107.250209@3] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
- [ 107.255309@3] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
- [ 107.260646@3] dhd_wlan_init_gpio: host_oob_irq: 100
- [ 107.265483@3] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
- [ 107.270909@3] dhd_wifi_platform_load: Enter
- [ 107.275082@3] Power-up adapter 'DHD generic adapter'
- [ 107.279965@3] wifi_platform_set_power = 1
- [ 107.283935@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 107.289315@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 107.496156@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 108.004895@0] wifi_platform_bus_enumerate device present 1
- [ 108.005071@0] ======== Card detection to detect SDIO card! ========
- [ 108.011232@0] sdio_reset_comm():
- [ 108.019021@6] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 108.130735@6] sdio: queuing unknown CIS tuple 0x80 (150 bytes)
- [ 108.170322@6] sdio: queuing unknown CIS tuple 0x48 (68 bytes)
- [ 108.173375@6] sdio: clk 200000000 SDR mode tuning start
- [ 108.176456@6] sdio: rx_tuning_result[1] = 10
- [ 108.180508@6] sdio: rx_tuning_result[2] = 10
- [ 108.185120@7] sdio: rx_tuning_result[3] = 10
- [ 108.189259@7] sdio: rx_tuning_result[4] = 10
- [ 108.192517@7] sdio: best_win_start =1, best_win_size =4
- [ 108.197758@7] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x32000
- [ 108.205442@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x32000
- [ 108.211198@0] [sdio_reinit] finish
- [ 110.214739@0] failed to power up DHD generic adapter, 3 retry left
- [ 110.232650@4] wifi_platform_set_power = 0
- [ 110.232703@4] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 110.236350@4] wifi_platform_bus_enumerate device present 0
- [ 110.241673@4] ======== Card detection to remove SDIO card! ========
- [ 110.247984@4] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 110.455017@3] wifi_platform_set_power = 1
- [ 110.455050@3] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 110.458671@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 110.665844@3] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 111.174790@3] wifi_platform_bus_enumerate device present 1
- [ 111.174963@3] ======== Card detection to detect SDIO card! ========
- [ 111.180926@3] sdio_reset_comm():
- [ 111.188372@6] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 111.192469@6] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 111.198819@6] sdio: Error resetting SDIO communications (-22)
- [ 111.204651@6] [sdio_reinit] finish
- [ 113.204518@6] failed to power up DHD generic adapter, 2 retry left
- [ 113.222649@6] wifi_platform_set_power = 0
- [ 113.222701@6] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 113.226263@6] wifi_platform_bus_enumerate device present 0
- [ 113.231658@6] ======== Card detection to remove SDIO card! ========
- [ 113.237956@6] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 113.444935@1] wifi_platform_set_power = 1
- [ 113.444967@1] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 113.448597@1] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 113.655537@1] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 114.164771@1] wifi_platform_bus_enumerate device present 1
- [ 114.164938@1] ======== Card detection to detect SDIO card! ========
- [ 114.170901@1] sdio_reset_comm():
- [ 114.179262@7] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 114.291134@7] sdio: queuing unknown CIS tuple 0x80 (150 bytes)
- [ 114.330219@6] sdio: queuing unknown CIS tuple 0x48 (68 bytes)
- [ 114.333257@6] sdio: clk 200000000 SDR mode tuning start
- [ 114.336356@6] sdio: rx_tuning_result[1] = 10
- [ 114.340446@6] sdio: rx_tuning_result[2] = 10
- [ 114.344750@7] sdio: rx_tuning_result[3] = 10
- [ 114.348862@7] sdio: rx_tuning_result[4] = 10
- [ 114.352397@7] sdio: best_win_start =1, best_win_size =4
- [ 114.357601@7] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x32000
- [ 114.365104@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x32000
- [ 114.371077@3] [sdio_reinit] finish
- [ 116.374715@3] failed to power up DHD generic adapter, 1 retry left
- [ 116.392838@7] wifi_platform_set_power = 0
- [ 116.392892@7] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 116.396459@7] wifi_platform_bus_enumerate device present 0
- [ 116.401836@7] ======== Card detection to remove SDIO card! ========
- [ 116.408113@7] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 116.615015@1] wifi_platform_set_power = 1
- [ 116.615047@1] ======== PULL WL_REG_ON(-1) HIGH! ========
- [ 116.618672@1] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 116.825612@1] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Enable! 240
- [ 117.334482@1] wifi_platform_bus_enumerate device present 1
- [ 117.334514@1] ======== Card detection to detect SDIO card! ========
- [ 117.340535@1] sdio_reset_comm():
- [ 117.347495@6] aml_sd_emmc d0070000.sdio: card claims to support voltages below defined range
- [ 117.352098@6] aml_sd_emmc d0070000.sdio: no support for card's volts
- [ 117.358521@6] sdio: Error resetting SDIO communications (-22)
- [ 117.364103@6] [sdio_reinit] finish
- [ 119.365102@2] failed to power up DHD generic adapter, 0 retry left
- [ 119.382987@4] wifi_platform_set_power = 0
- [ 119.383042@4] ======== PULL WL_REG_ON(-1) LOW! ========
- [ 119.386662@4] wifi_platform_bus_enumerate device present 0
- [ 119.391994@4] ======== Card detection to remove SDIO card! ========
- [ 119.398270@4] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 119.605170@0] failed to power up DHD generic adapter, max retry reached**
- [ 119.606351@0] unregister wifi platform drivers
- [ 119.610713@0] wifi_platform_bus_enumerate device present 0
- [ 119.616197@0] ======== Card detection to remove SDIO card! ========
- [ 119.622433@0] aml_wifi wifi.34: [extern_wifi_set_enable] WIFI Disable! 240
- [ 119.829299@0] ======== dhd_wlan_deinit_plat_data ========
- [ 119.829342@0] dhd_module_init: Failed to load the driver, try cnt 0
- [ 119.835335@0] dhd_module_init: Failed to load driver max retry reached**
- [ 119.841973@0] dhd_module_init: Exit err=-19
- [ 119.887052@0] aml_wifi wifi.34: [usb_power_control] Set WiFi power down
- [ 119.888031@0] aml_wifi wifi.34: [wifi_power_ioctl] ioctl Set sdio wifi power down!
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement