API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Nov 22nd, 2018
198
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 70.11 KB | None | 0 0
raw download clone embed print report
  1. =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.11.22 14:00:03 =~=~=~=~=~=~=~=~=~=~=~=
  2. GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:80;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
  3. TE: 89423
  4.  
  5. BL2 Built : 20:32:17, Sep 8 2017.
  6. gxl g6296b83 - xiaobo.gu@droid12
  7.  
  8. set vdd cpu_a to 1120 mv
  9. set vdd cpu_b to 1050 mv
  10. set vddee to 1000 mv
  11. Board ID = 10
  12. CPU clk: 1200MHz
  13. DQS-corr enabled
  14. DDR scramble enabled
  15. STICKY_REG0: 0x00000000
  16. STICKY_REG1: 0x00000000
  17. STICKY_REG9: 0x00000000
  18. LPDDR3 chl: Rank0+1 @ 792MHz
  19. DDR0_PUB_CATR0 1 value
  20. DDR0_PUB_CATR0: 0x00141020....
  21. DDR0_PUB_CATR1: 0x0203aaaa....
  22. DDR0_PUB_PGSR0: 0x8000003f....
  23. Rank0: 2048MB(auto)-2T-3
  24. Rank1: 1024MB(auto)-2T-3
  25. DataBus test pass!
  26. AddrBus test pass!
  27. -s
  28. Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
  29. New fip structure!
  30. Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
  31. Load bl31 from eMMC, src: 0x00020200, des: 0x05100000, size: 0x0002c600
  32. Load bl33 from eMMC, src: 0x00050200, des: 0x01000000, size: 0x00066600
  33. NOTICE: BL3-1: v1.0(release):a625749
  34. NOTICE: BL3-1: Built : 11:25:15, Aug 25 2017
  35. NOTICE: BL31: BL33 decompress pass
  36. mpu_config_enable:ok
  37.  
  38. [Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07]
  39.  
  40. OPS=0x82
  41.  
  42. wdt: reset registers!
  43.  
  44. 24 f 34 3e 3e 47 e0 46 6f c0 f1 58 [0.334089 Inits done]
  45.  
  46. secure task start!
  47. high task start!
  48. low task start!
  49. ERROR: Error initializing runtime service opteed_fast
  50.  
  51.  
  52. U-Boot 2015.01-g2735815-dirty (Nov 01 2018 - 19:36:29)
  53.  
  54. DRAM: 3 GiB
  55. Relocation Offset is: b6eb5000
  56. register usb cfg[0][1] = 00000000b7f5ac28
  57. [CANVAS]canvas init
  58. boot_device_flag : 1
  59. Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
  60. init bus_cycle=6, bus_timing=7, system=5.0ns
  61. reset failed
  62. get_chip_type and ret:fffffffe
  63. get_chip_type and ret:fffffffe
  64. chip detect failed and ret:fffffffe
  65. nandphy_init failed and ret=0xfffffff1
  66. MMC: aml_priv->desc_buf = 0x00000000b3eb56b0
  67. aml_priv->desc_buf = 0x00000000b3eb79d0
  68. SDIO Port B: 0, SDIO Port C: 1
  69. emmc/sd response timeout, cmd8, status=0x1ff2800
  70. emmc/sd response timeout, cmd55, status=0x1ff2800
  71. init_part() 293: PART_TYPE_AML
  72. [mmc_init] mmc init success
  73. dtb magic 5f4c4d41
  74. Amlogic multi-dtb tool
  75. Multi dtb detected
  76. Multi dtb tool version: v2 .
  77. Support 3 dtbs.
  78. aml_dt soc: gxm platform: q201 variant: 3g
  79. dtb 0 soc: gxm plat: q201 vari: 1g
  80. dtb 1 soc: gxm plat: q201 vari: 2g
  81. dtb 2 soc: gxm plat: q201 vari: 3g
  82. Find match dtb: 2
  83. start dts,buffer=00000000b3eba200,dt_addr=00000000b3ed0a00
  84. Amlogic multi-dtb tool
  85. Multi dtb detected
  86. Multi dtb tool version: v2 .
  87. Support 3 dtbs.
  88. aml_dt soc: gxm platform: q201 variant: 3g
  89. dtb 0 soc: gxm plat: q201 vari: 1g
  90. dtb 1 soc: gxm plat: q201 vari: 2g
  91. dtb 2 soc: gxm plat: q201 vari: 3g
  92. Find match dtb: 2
  93. parts: 10
  94. 00: logo 0000000002000000 1
  95. 01: recovery 0000000002000000 1
  96. 02: rsv 0000000000800000 1
  97. 03: tee 0000000000800000 1
  98. 04: crypt 0000000002000000 1
  99. 05: misc 0000000002000000 1
  100. 06: boot 0000000002000000 1
  101. 07: system 0000000080000000 1
  102. 08: cache 0000000020000000 2
  103. 09: data ffffffffffffffff 4
  104. init_part() 293: PART_TYPE_AML
  105. eMMC/TSD partition table have been checked OK!
  106. check pattern success
  107. mmc env offset: 0x27400000
  108. In: serial
  109. Out: serial
  110. Err: serial
  111. reboot_mode=cold_boot
  112. [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
  113. _verify_dtb_checksum()-917: calc 145e7f63, store 145e7f63
  114. _verify_dtb_checksum()-917: calc 145e7f63, store 145e7f63
  115. dtb_read()-1039: total valid 2
  116. dtb_read()-1106: do nothing
  117. Amlogic multi-dtb tool
  118. Multi dtb detected
  119. Multi dtb tool version: v2 .
  120. Support 3 dtbs.
  121. aml_dt soc: gxm platform: q201 variant: 3g
  122. dtb 0 soc: gxm plat: q201 vari: 1g
  123. dtb 1 soc: gxm plat: q201 vari: 2g
  124. dtb 2 soc: gxm plat: q201 vari: 3g
  125. Find match dtb: 2
  126. vpu: clk_level in dts: 7
  127. vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
  128. vpu: vpu_clk_gate_init_off
  129. vpp: vpp_init
  130. hpd_state=0
  131. cvbs performance type = 6, table = 0
  132. vpp: vpp_pq_load pq val error !!!
  133. Net: dwmac.c9410000amlkey_init() enter!
  134. [EFUSE_MSG]keynum is 4
  135. [BL31]: tee size: 0
  136.  
  137. Start read misc partition datas!
  138. info->attemp_times = 0
  139. info->active_slot = 0
  140. info->slot_info[0].bootable = 1
  141. info->slot_info[0].online = 1
  142. info->slot_info[1].bootable = 0
  143. info->slot_info[1].online = 0
  144. info->attemp_times = 0
  145. attemp_times = 0
  146. active slot = 0
  147. wipe_data=successful
  148. wipe_cache=successful
  149. upgrade_step=2
  150. [OSD]load fb addr from dts
  151. [OSD]fb_addr for logo: 0xbf851000
  152. [OSD]load fb addr from dts
  153. [OSD]fb_addr for logo: 0xbf851000
  154. [CANVAS]addr=0xbf851000 width=3840, height=2160
  155. amlkey_init() enter!
  156. amlkey_init() 71: already init!
  157. [EFUSE_MSG]keynum is 4
  158. [BL31]: tee size: 0
  159. [KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
  160. [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
  161. gpio: pin GPIOAO_2 (gpio 102) value is 1
  162. Hit Enter or space or Ctrl+C key to stop autoboot -- : 1  0
  163. ee_gate_off ...
  164. ## Booting Android Image at 0x01080000 ...
  165. reloc_addr =b3f3a450
  166. copy done
  167. Kernel command line: buildvariant=userdebug
  168. load dtb from 0x1000000 ......
  169. Amlogic multi-dtb tool
  170. Single dtb detected
  171. Uncompressing Kernel Image ... OK
  172. kernel loaded at 0x01080000, end = 0x021dce30
  173. Loading Ramdisk to b3d62000, end b3ea296e ... OK
  174. Loading Device Tree to 000000001fff2000, end 000000001ffffdc0 ... OK
  175. fdt_instaboot: no instaboot image
  176.  
  177. Starting kernel ...
  178.  
  179. uboot time: 1976316 us
  180. [ 0.000000@0] Initializing cgroup subsys cpu
  181. [ 0.000000@0] Initializing cgroup subsys cpuacct
  182. [ 0.000000@0] Linux version 3.14.29-g06f5df453ba (server@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Sat May 26 11:24:07 CST 2018
  183. [ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
  184. [ 0.000000@0] no prop version_code
  185. [ 0.000000@0] bootconsole [earlycon0] enabled
  186. [ 0.000000@0] fdt Reserved memory table:
  187. [ 0.000000@0] linux,di: 0x00000000be200000 - 0x00000000c0000000 (30 MiB)
  188. [ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x00000000be200000, size 30 MiB
  189. [ 0.000000@0] linux,chunk-reserve: 0x00000000ba200000 - 0x00000000be200000 (64 MiB)
  190. [ 0.000000@0] linux,ion-dev: 0x00000000b6200000 - 0x00000000ba200000 (64 MiB)
  191. [ 0.000000@0] linux,vdin1_cma: 0x00000000b5000000 - 0x00000000b6000000 (16 MiB)
  192. [ 0.000000@0] cma: Reserved 16 MiB at b5000000, total cma pages:4096
  193. [ 0.000000@0] linux,ppmgr: 0x00000000b6200000 - 0x00000000b6200000 (0 MiB)
  194. [ 0.000000@0] linux,codec_mm_cma: 0x000000009ec00000 - 0x00000000b3c00000 (336 MiB)
  195. [ 0.000000@0] cma: Reserved 336 MiB at 9ec00000, total cma pages:90112
  196. [ 0.000000@0] linux,picdec: 0x00000000b6200000 - 0x00000000b6200000 (0 MiB)
  197. [ 0.000000@0] Reserved memory: incorrect alignment of CMA region
  198. [ 0.000000@0] linux,codec_mm_reserved: 0x000000009ab00000 - 0x000000009ec00000 (65 MiB)
  199. [ 0.000000@0] fdt Reserved memory total: 579 MiB
  200. [ 0.000000@0] cma: Reserved 8 MiB at b4800000, total cma pages:92160
  201. [ 0.000000@0] psci: Using PSCI v0.1 Function IDs from DT
  202. [ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc0b6160000 s19968 r8192 d20992 u49152
  203. [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 774403
  204. [ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3d800000,576cvbs maxcpus=8 vout=576cvbs,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 pq= androidboot.firstboot=1 jtag=apao androidboot.hardware=amlogic mac=C4:2A:FE:88:98:31 androidboot.mac=C4:2A:FE:88:98:31 androidboot.slot_suffix=_a buildvariant=userdebug
  205. [ 0.000000@0] logo: osd1
  206. [ 0.000000@0] logo: loaded
  207. [ 0.000000@0] logo: 0x3d800000
  208. [ 0.000000@0] logo: 576cvbs
  209. [ 0.000000@0] vout_serve: 576cvbs
  210. [ 0.000000@0] vout_serve: enable: 1
  211. [ 0.000000@0] logo: get hdmimode: 1080p60hz
  212. [ 0.000000@0] logo: get cvbsmode: 576cvbs
  213. [ 0.000000@0] tv_vout: cvbs performance line = 0
  214. [ 0.000000@0] [amvecm] pq string error !!!
  215. [ 0.000000@0] jtag: jtag select 2
  216. [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
  217. [ 0.000000@0] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
  218. [ 0.000000@0] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
  219. [ 0.000000@0] Memory: 2470828K/3140608K available (11014K kernel code, 1255K rwdata, 4160K rodata, 1343K init, 3813K bss, 669780K reserved)
  220. [ 0.000000@0] Virtual kernel memory layout:
  221. [ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff807fff0000 ( 2047 MB)
  222. [ 0.000000@0] vmemmap : 0xffffff8080000000 - 0xffffff8082a00000 ( 42 MB)
  223. [ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
  224. [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc0c0000000 ( 3072 MB)
  225. [ 0.000000@0] .init : 0xffffffc001f53000 - 0xffffffc0020a2e00 ( 1344 kB)
  226. [ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001f52814 ( 15179 kB)
  227. [ 0.000000@0] .data : 0xffffffc0020a3000 - 0xffffffc0021dce30 ( 1256 kB)
  228. [ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01f51fff]
  229. [ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
  230. [ 0.000000@0] arch_multi_cluster:1
  231. [ 0.000000@0] Preemptible hierarchical RCU implementation.
  232. [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
  233. [ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
  234. [ 0.000005@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
  235. [ 0.008247@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
  236. [ 0.016850@0] Console: colour dummy device 80x25
  237. [ 0.021097@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
  238. [ 0.031671@0] pid_max: default: 32768 minimum: 301
  239. [ 0.036590@0] Security Framework initialized
  240. [ 0.040787@0] SELinux: Initializing.
  241. [ 0.044536@0] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
  242. [ 0.051367@0] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
  243. [ 0.065335@0] Initializing cgroup subsys debug
  244. [ 0.065377@0] Initializing cgroup subsys freezer
  245. [ 0.068901@0] ftrace: allocating 37914 entries in 149 pages
  246. [ 0.125442@0] /cpus/cpu@0: Missing clock-frequency property
  247. [ 0.125484@0] /cpus/cpu@1: Missing clock-frequency property
  248. [ 0.131065@0] /cpus/cpu@2: Missing clock-frequency property
  249. [ 0.136695@0] /cpus/cpu@3: Missing clock-frequency property
  250. [ 0.142267@0] /cpus/cpu@100: Missing clock-frequency property
  251. [ 0.148049@0] /cpus/cpu@101: Missing clock-frequency property
  252. [ 0.153818@0] /cpus/cpu@102: Missing clock-frequency property
  253. [ 0.159600@0] /cpus/cpu@103: Missing clock-frequency property
  254. [ 0.165369@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
  255. [ 0.215734@0] Meson chip version = RevA (22:A - 82:0)
  256. [ 0.234111@1] CPU1: Booted secondary processor
  257. [ 0.254072@2] CPU2: Booted secondary processor
  258. [ 0.274080@3] CPU3: Booted secondary processor
  259. [ 0.294113@4] CPU4: Booted secondary processor
  260. [ 0.314106@5] CPU5: Booted secondary processor
  261. [ 0.334124@6] CPU6: Booted secondary processor
  262. [ 0.354154@7] CPU7: Booted secondary processor
  263. [ 0.354249@0] Brought up 8 CPUs
  264. [ 0.383068@0] SMP: Total of 8 processors activated.
  265. [ 0.397278@2] sched: registering cpufreq notifiers for scale-invariant loads
  266. [ 0.398808@2] instabooting: 0
  267. [ 0.414473@2] cma: cma_init_reserved_areas, use_cma_first:1
  268. [ 0.414598@2] pinctrl core: initialized pinctrl subsystem
  269. [ 0.420639@2] regulator-dummy: no parameters
  270. [ 0.425164@3] NET: Registered protocol family 16
  271. [ 0.431349@2] ramoops: using module parameters
  272. [ 0.433942@2] console [pstore-1] enabled
  273. [ 0.437258@2] pstore: Registered ramoops as persistent store backend
  274. [ 0.443632@2] ramoops: attached 0x100000@0x7300000, ecc: 0/0
  275. [ 0.450364@2] cpuidle: using governor menu
  276. [ 0.453722@2] aml_vdac_init: module init
  277. [ 0.457547@2] register canvas platform driver
  278. [ 0.461854@3] register rdma platform driver
  279. [ 0.468202@3] vdso: 2 pages (1 code, 1 data) at base ffffffc0020ac000
  280. [ 0.472464@3] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  281. [ 0.479819@3] DMA: preallocated 256 KiB pool for atomic allocations
  282. [ 0.486848@3] software IO TLB [mem 0x96c00000-0x97000000] (4MB) mapped at [ffffffc096c00000-ffffffc096ffffff]
  283. [ 0.495729@3] Serial: AMBA PL011 UART driver
  284. [ 0.500666@2] aml_i2c version: 20140813
  285. [ 0.504130@2] i2c-core: driver [pmu4] using legacy resume method
  286. [ 0.510047@3] codec_mm:codec_mm_module_init
  287. [ 0.514157@3] media_configs_system_init
  288. [ 0.518114@2] aml_watch_point_probe, in
  289. [ 0.522288@3] meson_mpll_clk: register mpll_clk_out0 success done
  290. [ 0.527899@3] meson_mpll_clk: register mpll_clk_out1 success done
  291. [ 0.534036@3] meson_mpll_clk: register mpll_clk_out2 success done
  292. [ 0.540356@3] clk_sys: register PLL sys_pll success done
  293. [ 0.545498@3] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
  294. [ 0.550819@3] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
  295. [ 0.556024@3] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
  296. [ 0.561494@3] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
  297. [ 0.567450@3] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
  298. [ 0.573394@3] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
  299. [ 0.579268@3] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
  300. [ 0.585119@3] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
  301. [ 0.590986@3] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
  302. [ 0.596869@3] gxl_clk: clock initialization complete
  303. [ 0.602019@3] clkmsr: Gxl msr_clk_reg0=ffffff800003c75c,msr_clk_reg2=ffffff800003e764
  304. [ 0.612599@2] aml_iomap: amlogic iomap probe done
  305. [ 0.615196@2] pinmux-gxl c1109880.pinmux: Init pinux probe!
  306. [ 0.621399@2] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
  307. [ 0.627262@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
  308. [ 0.634767@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
  309. [ 0.643007@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
  310. [ 0.650854@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
  311. domain-0 init dvfs: 4
  312.  
  313. domain-1 init dvfs: 4
  314.  
  315. [ 0.671763@2] codec_mm has 2 memory regions
  316. [ 0.671840@2] codec_mm codec_mm.22: assigned reserved memory node linux,codec_mm_cma ok
  317. [ 0.678441@2] codec_mm codec_mm.22: assigned reserved memory node linux,codec_mm_reserved ok
  318. [ 0.687067@2] codec_mm has 2 memory regions
  319. [ 0.691134@2] codec_mm codec_mm.22: assigned reserved memory node linux,codec_mm_cma ok
  320. [ 0.699182@2] codec_mm codec_mm.22: assigned reserved memory node linux,codec_mm_reserved ok
  321. [ 0.710245@2] vpu: driver version: v04
  322. [ 0.711441@2] vpu: load vpu_clk: 666667000Hz(7)
  323. [ 0.716095@3] vpu: vpu_probe OK
  324. [ 0.720939@2] tv_vout: tvout_probe
  325. [ 0.722536@2] tv_vout: chrdev devno 266338304 for disp
  326. [ 0.727691@2] vout_notify: vout_register_server
  327. [ 0.732281@2] tv_vout: register tv module server ok
  328. [ 0.737424@2] tv_vout: create cdev tv
  329. [ 0.740818@2] tv_vout: tvout_probe OK
  330. [ 0.745214@2] canvas_probe reg=00000000c8838000,size=400
  331. [ 0.749856@2] canvas maped reg_base =ffffff800009a000
  332. [ 0.759297@3] rdma_probe
  333. [ 1.173450@0] bio: create slab <bio-0> at 0
  334. [ 1.174721@1] SCSI subsystem initialized
  335. [ 1.176774@0] usbcore: registered new interface driver usbfs
  336. [ 1.181812@0] usbcore: registered new interface driver hub
  337. [ 1.187402@1] usbcore: registered new device driver usb
  338. [ 1.193483@0] i2c-gpio i2c_gpio.43: using pins 172 (SDA) and 173 (SCL)
  339. [ 1.199653@0] Linux video capture interface: v2.00
  340. [ 1.204135@1] pps_core: LinuxPPS API ver. 1 registered
  341. [ 1.209170@1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  342. [ 1.218480@0] PTP clock support registered
  343. [ 1.223637@1] hdmitx: system: Ver: 2014May6
  344. [ 1.226898@1] hdmitx: amhdmitx_probe
  345. [ 1.230694@2] hdmitx: hdmi_init_chip_type: 0
  346. [ 1.234634@2] hdmitx hpd irq = 89
  347. [ 1.238757@1] hdmitx20: Mapped PHY: 0xc1100000
  348. [ 1.242428@1] hdmitx20: Mapped PHY: 0xc8834400
  349. [ 1.246803@1] hdmitx20: Mapped PHY: 0xd0100000
  350. [ 1.251270@1] hdmitx20: Mapped PHY: 0xc8100000
  351. [ 1.255728@1] hdmitx20: Mapped PHY: 0xc883c000
  352. [ 1.260183@1] hdmitx20: Mapped PHY: 0xc1104400
  353. [ 1.264644@1] hdmitx20: Mapped PHY: 0xc883a000
  354. [ 1.269248@1] hdmitx20: Mapped PHY: 0xda83a000
  355. [ 1.273570@1] hdmitx20: Mapped PHY: 0xd0044000
  356. [ 1.278273@1] avmute set to 1
  357. [ 1.281017@1] hdmitx: attr default
  358. [ 1.285059@3] tv_vout: tv_set_current_vmode[925]fps_target_mode=8
  359. [ 1.290569@3] tv_vout: mode is 8,sync_duration_den=1,sync_duration_num=50
  360. [ 1.297378@3] tv_vout: already display in uboot
  361. [ 1.301946@3] vout_serve: vinfo mode is: 576cvbs
  362. [ 1.306556@3] vout_serve: init mode 576cvbs
  363. [ 1.311028@2] vout_serve: create_vout_fops OK
  364. [ 1.315132@2] vout_serve: create vout attribute OK
  365. [ 1.319965@2] vout_serve: meson_vout_probe OK
  366. [ 1.324558@3] logo: logo_init
  367. [ 1.327730@3] osd_rdma: osd_rdma_init: rdma_table p=0xb4841000,op=0xb4841000 , v=0xffffff80000b9000
  368. [ 1.336469@3] rdma_register, rdma_table_addr ffffff80000c9000 rdma_table_addr_phy b4842000 reg_buf ffffffc097127000
  369. [ 1.346902@3] rdma_register success, handle 1 table_size 4096
  370. [ 1.352668@3] osd_rdma: osd_rdma_init:osd reset rdma handle = 1.
  371. [ 1.358742@3] rdma_register, rdma_table_addr ffffff80000d9000 rdma_table_addr_phy b4843000 reg_buf ffffffc0970ea000
  372. [ 1.369213@3] rdma_register success, handle 2 table_size 4096
  373. [ 1.374980@3] osd_rdma: osd_rdma_init:osd rdma handle = 2.
  374. [ 1.381061@2] Advanced Linux Sound Architecture Driver Initialized.
  375. [ 1.387500@2] Bluetooth: Core ver 2.18
  376. [ 1.390703@3] NET: Registered protocol family 31
  377. [ 1.395195@3] Bluetooth: HCI device and connection manager initialized
  378. [ 1.401781@3] Bluetooth: HCI socket layer initialized
  379. [ 1.406834@3] Bluetooth: L2CAP socket layer initialized
  380. [ 1.412133@3] Bluetooth: SCO socket layer initialized
  381. [ 1.417163@3] NetLabel: Initializing
  382. [ 1.420742@3] NetLabel: domain hash size = 128
  383. [ 1.425300@3] NetLabel: protocols = UNLABELED CIPSOv4
  384. [ 1.430506@3] NetLabel: unlabeled traffic allowed by default
  385. [ 1.438858@2] Switched to clocksource arch_sys_counter
  386. [ 1.484288@2] register gxtv_demod demod driver
  387. [ 1.484743@0] [amlatvdemod..]aml_atvdemod_init.
  388. [ 1.487815@0] NET: Registered protocol family 2
  389. [ 1.492881@0] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
  390. [ 1.500043@0] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
  391. [ 1.507076@0] TCP: Hash tables configured (established 32768 bind 32768)
  392. [ 1.513396@0] TCP: reno registered
  393. [ 1.516690@0] UDP hash table entries: 2048 (order: 4, 65536 bytes)
  394. [ 1.523026@0] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
  395. [ 1.530161@0] NET: Registered protocol family 1
  396. [ 1.534385@0] RPC: Registered named UNIX socket transport module.
  397. [ 1.540283@0] RPC: Registered udp transport module.
  398. [ 1.545115@0] RPC: Registered tcp transport module.
  399. [ 1.550026@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
  400. [ 1.556838@0] pwm: output_co = 16 ; clock_co = 8
  401. [ 1.561375@0] pwm: npwm= 16
  402. [ 1.564350@2] pwm: probe ok
  403. [ 1.567355@3] wifi: power_on_pin_OD = 0;
  404. [ 1.570870@3] aml_wifi wifi.38: [wifi_dev_probe] no power_on_pin2
  405. [ 1.577004@3] aml_wifi wifi.38: [pwm_double_channel_conf_dt] pwm phandle val=3e;pwm-channel1=4;pwm-channel2=12
  406. [ 1.587039@3] aml_wifi wifi.38: [pwm_double_channel_conf_dt] pwm_config1[0] = 30541
  407. [ 1.594776@3] aml_wifi wifi.38: [pwm_double_channel_conf_dt] pwm_config2[0] = 30518
  408. [ 1.602437@3] aml_wifi wifi.38: [pwm_double_channel_conf_dt] pwm_config1[1] = 15270
  409. [ 1.610136@3] aml_wifi wifi.38: [pwm_double_channel_conf_dt] pwm_config2[1] = 15259
  410. [ 1.617831@3] aml_wifi wifi.38: [pwm_double_channel_conf_dt] pwm_config1[2] = 6
  411. [ 1.625186@3] aml_wifi wifi.38: [pwm_double_channel_conf_dt] pwm_config2[2] = 9
  412. [ 1.632535@3] aml_wifi wifi.38: [pwm_double_channel_conf_dt] wifi pwm dt ok
  413. [ 1.639554@3] aml_wifi wifi.38: [pwm_double_channel_conf] wifi pwm conf ok
  414. [ 1.646492@3] aml_wifi wifi.38: [wifi_dev_probe] dhd_static_buf setup
  415. [ 1.652994@3] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
  416. [ 1.660537@3] aml_wifi wifi.38: [wifi_dev_probe] interrupt_pin=241
  417. [ 1.666743@3] aml_wifi wifi.38: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
  418. [ 1.674185@3] aml_wifi wifi.38: [wifi_dev_probe] power_on_pin=240
  419. [ 1.680310@3] aml_wifi wifi.38: [wifi_dev_probe] clock_32k_pin=0
  420. [ 1.686689@2] aml_wifi wifi.38: [wifi_setup_dt] wifi_setup_dt
  421. [ 1.692167@2] aml_wifi wifi.38: [wifi_setup_dt] interrupt_pin(241)
  422. [ 1.698340@2] aml_wifi wifi.38: [wifi_setup_dt] power_on_pin(240)
  423. [ 1.704854@3] Unpacking initramfs...
  424. [ 1.755031@3] Freeing initrd memory: 1280K (ffffffc0b3d62000 - ffffffc0b3ea2000)
  425. [ 1.762618@2] futex hash table entries: 2048 (order: 5, 131072 bytes)
  426. [ 1.763612@2] Initialise system trusted keyring
  427. [ 1.768099@2] audit: initializing netlink subsys (disabled)
  428. [ 1.773722@2] audit: type=2000 audit(1.690:1): initialized
  429. [ 1.780135@2] HugeTLB registered 2 MB page size, pre-allocated 0 pages
  430. [ 1.793445@3] VFS: Disk quotas dquot_6.5.2
  431. [ 1.793732@3] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
  432. [ 1.803939@3] NFS: Registering the id_resolver key type
  433. [ 1.804007@3] Key type id_resolver registered
  434. [ 1.808255@3] Key type id_legacy registered
  435. [ 1.812573@3] NTFS driver 2.1.30 [Flags: R/O].
  436. [ 1.817362@2] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
  437. [ 1.825203@2] fuse init (API version 7.22)
  438. [ 1.829021@2] msgmni has been set to 5548
  439. [ 1.833982@3] NET: Registered protocol family 38
  440. [ 1.836967@3] Key type asymmetric registered
  441. [ 1.841265@3] Asymmetric key parser 'x509' registered
  442. [ 1.846767@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
  443. [ 1.854061@2] io scheduler noop registered
  444. [ 1.858043@2] io scheduler deadline registered
  445. [ 1.862822@3] io scheduler cfq registered (default)
  446. [ 1.920226@3] meson-rng c8834000.rng: hwrng registered
  447. [ 1.924002@2] loop: module loaded
  448. [ 1.924669@2] zram: Created 1 device(s) ...
  449. [ 1.928370@2] mtdoops: mtd device (mtddev=name/number) must be supplied
  450. [ 1.935381@2] tun: Universal TUN/TAP device driver, 1.6
  451. [ 1.939257@2] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  452. [ 2.070698@3] libphy: stmmac: probed
  453. [ 2.070736@3] eth0: PHY ID 03815c11 at 1 IRQ POLL (stmmac-0:01) active
  454. [ 2.075781@2] PPP generic driver version 2.4.2
  455. [ 2.080006@3] PPP BSD Compression module registered
  456. [ 2.084635@3] PPP Deflate Compression module registered
  457. [ 2.089935@3] PPP MPPE Compression module registered
  458. [ 2.094870@3] NET: Registered protocol family 24
  459. [ 2.099725@2] usbcore: registered new interface driver asix
  460. [ 2.105285@2] usbcore: registered new interface driver ax88179_178a
  461. [ 2.111584@3] usbcore: registered new interface driver cdc_ether
  462. [ 2.117576@3] usbcore: registered new interface driver net1080
  463. [ 2.123497@2] usbcore: registered new interface driver cdc_subset
  464. [ 2.129599@2] usbcore: registered new interface driver zaurus
  465. [ 2.135359@3] usbcore: registered new interface driver cdc_ncm
  466. [ 2.141466@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  467. [ 2.147809@2] ehci-h20ahb: H20AHB-EHCI Host Controller driver
  468. [ 2.153920@3] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  469. [ 2.160525@2] usbcore: registered new interface driver cdc_acm
  470. [ 2.165835@2] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  471. [ 2.174243@3] usbcore: registered new interface driver usb-storage
  472. [ 2.180612@2] usbcore: registered new interface driver usbserial
  473. [ 2.187107@3] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff800010e000
  474. [ 2.197347@3] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
  475. [ 2.203846@3] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff800011a080
  476. [ 2.215263@2] mousedev: PS/2 mouse device common for all mice
  477. [ 2.220975@2] usbcore: registered new interface driver xpad
  478. [ 2.226090@2] i2c /dev entries driver
  479. [ 2.230108@3] IR NEC protocol handler initialized
  480. [ 2.234260@3] IR RC5(x) protocol handler initialized
  481. [ 2.239277@3] IR RC6 protocol handler initialized
  482. [ 2.243969@3] IR JVC protocol handler initialized
  483. [ 2.248694@3] IR Sony protocol handler initialized
  484. [ 2.253515@3] IR RC5 (streamzap) protocol handler initialized
  485. [ 2.259325@3] IR SANYO protocol handler initialized
  486. [ 2.264182@3] IR MCE Keyboard/mouse protocol handler initialized
  487. [ 2.270440@2] usbcore: registered new interface driver uvcvideo
  488. [ 2.276170@2] USB Video Class driver (1.1.1)
  489. [ 2.280648@2] usbcore: registered new interface driver cx231xx
  490. [ 2.286322@2] cx231xx: Cx231xx dvb Extension initialized
  491. [ 2.292649@2] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
  492. [ 2.300488@2] Bluetooth: HCI UART driver ver 2.2
  493. [ 2.304960@2] Bluetooth: HCI H4 protocol initialized
  494. [ 2.310352@2] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
  495. [ 2.317712@0] cpu cpu4: bL_cpufreq_init: CPU 4 initialized
  496. [ 2.321206@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
  497. [ 2.328987@0] CPUidle arm64: cpuidle init start!!
  498. [ 2.333949@0] CPUidle arm64: cpuidle init done!
  499. [ 2.338646@2] hidraw: raw HID events driver (C) Jiri Kosina
  500. [ 2.344021@2] @@@@@@@@@@_____2______in dia_init()
  501. [ 2.348272@2] ATVR driver - init called!
  502. [ 2.352628@3] usbcore: registered new interface driver usbhid
  503. [ 2.357981@3] usbhid: USB HID core driver
  504. [ 2.362633@2] ashmem: initialized
  505. [ 2.365497@3] logger: created 256K log 'log_main'
  506. [ 2.370557@3] logger: created 256K log 'log_events'
  507. [ 2.375128@2] logger: created 256K log 'log_radio'
  508. [ 2.380217@3] logger: created 256K log 'log_system'
  509. [ 2.385940@3] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff800011c4c0
  510. [ 2.391885@3] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
  511. [ 2.406896@3] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
  512. [ 2.409547@3] console [ttyS0] enabled
  513. [ 2.409547@3] console [ttyS0] enabled
  514. [ 2.416765@3] bootconsole [earlycon0] disabled
  515. [ 2.416765@3] bootconsole [earlycon0] disabled
  516. [ 2.425978@2] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff800011e4c0
  517. [ 2.432634@2] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
  518. [ 2.442544@3] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
  519. [ 2.451846@3] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
  520. [ 2.459499@2] hdmitx_hdcp_init
  521. [ 2.462756@0] aml_vrtc rtc.37: rtc core: registered aml_vrtc as rtc0
  522. [ 2.468515@2] BLASTER Driver Init
  523. [ 2.472494@3] secmon has 1 memory regions
  524. [ 2.475636@3] secmon: share in base: 0xffffff800013a000, share out base: 0xffffff800013c000
  525. [ 2.483939@3] secmon secmon.4: assigned reserved memory node linux,secmon ok
  526. [ 2.490865@3] secmon: probe done
  527. [ 2.494620@3] storage: storage in base: 0xffffff8001800000
  528. [ 2.499527@3] storage: storage out base: 0xffffff8001880000
  529. [ 2.504998@3] storage: storage block base: 0xffffff8001900000
  530. [ 2.510699@3] storage: probe done!
  531. [ 2.514902@2] aml_sd_emmc_probe: line 3608
  532. [ 2.518112@2] mmc driver version: 1.07, 2017-4-26: Support new emmc host controller for version 3
  533. [ 2.527581@2] aml_sd_emmc_reg_init 1152
  534. [ 2.530797@2] get property: ocr_avail, value:0x00200080
  535. [ 2.537171@2] get property: f_min, value:300000
  536. [ 2.543310@2] get property: f_max, value:100000000
  537. [ 2.549694@2] get property: max_req_size, value:0x00020000
  538. [ 2.556150@2] get property: pinname, str:emmc
  539. [ 2.561930@2] get property: card_type, value:1
  540. [ 2.567635@2] get property: gpio_dat3, str:
  541. [ 2.573068@2] get property: hw_reset, str:
  542. [ 2.578514@2] emmc:pdata->caps = c0000d47
  543. [ 2.582461@2] emmc:pdata->caps2 = 18060
  544. [ 2.586246@2] emmc:pdata->pm_caps = 0
  545. [ 2.589890@2] storage 1, boot 1
  546. [ 2.592973@2] get_storage_dev return 1
  547. [ 2.628878@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  548. [ 2.629109@3] aml_sd_emmc_probe: line 3608
  549. [ 2.633538@3] aml_sd_emmc_reg_init 1152
  550. [ 2.636970@3] get property: ocr_avail, value:0x00200080
  551. [ 2.643426@3] get property: f_min, value:400000
  552. [ 2.649524@3] get property: f_max, value:100000000
  553. [ 2.655894@3] get property: max_req_size, value:0x00020000
  554. [ 2.662378@3] get property: irq_in, value:3
  555. [ 2.668054@3] get property: irq_out, value:5
  556. [ 2.673772@3] get property: gpio_cd, str:
  557. [ 2.679188@3] get property: pinname, str:sd
  558. [ 2.684791@3] get property: jtag_pin, str:
  559. [ 2.690256@3] get property: card_type, value:5
  560. [ 2.694374@1] emmc: BKOPS_EN bit is not set
  561. [ 2.700126@3] get property: gpio_dat3, str:
  562. [ 2.701527@1] emmc: trying cali 0-th time(s)
  563. [ 2.707520@1] emmc: delay[0]= 0 padding= 4, bidx=0
  564. [ 2.707524@1] emmc: delay[1]= 0 padding= 4, bidx=0
  565. [ 2.707526@1] emmc: delay[2]= 0 padding= 4, bidx=0
  566. [ 2.707529@1] emmc: delay[3]= 250 padding= 3, bidx=0
  567. [ 2.707531@1] emmc: delay[4]= 250 padding= 3, bidx=0
  568. [ 2.707533@1] emmc: delay[5]= 250 padding= 3, bidx=0
  569. [ 2.707535@1] emmc: delay[6]= 0 padding= 4, bidx=0
  570. [ 2.707537@1] emmc: delay[7]= 250 padding= 3, bidx=0
  571. [ 2.707539@1] emmc: calibration result @ 0: max(250), min(0)
  572. [ 2.707542@1] emmc: line_delay =0x1000111, max_cal_result =250
  573. [ 2.707544@1] emmc: base_index_max 0, base_index_min 0
  574. [ 2.707552@1] emmc: clk 100000000 SDR mode tuning start
  575. [ 2.707981@1] emmc: rx_tuning_result[1] = 10
  576. [ 2.708367@1] emmc: rx_tuning_result[2] = 10
  577. [ 2.708750@1] emmc: rx_tuning_result[3] = 10
  578. [ 2.709146@1] emmc: rx_tuning_result[4] = 10
  579. [ 2.709532@1] emmc: rx_tuning_result[5] = 10
  580. [ 2.709915@1] emmc: rx_tuning_result[6] = 10
  581. [ 2.710301@1] emmc: rx_tuning_result[7] = 10
  582. [ 2.710685@1] emmc: rx_tuning_result[8] = 10
  583. [ 2.710725@1] emmc: best_win_start =1, best_win_size =8
  584. [ 2.710728@1] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x52000
  585. [ 2.710731@1] emmc: gclock =0x100024a, gdelay=0x1000111, gadjust=0x52000
  586. [ 2.711500@1] emmc: support driver strength type 1
  587. [ 2.711777@1] emmc: try set sd/emmc to DDR mode
  588. [ 2.711781@1] emmc: try set sd/emmc to DDR mode
  589. [ 2.712510@1] emmc: new HS400 MMC card at address 0001
  590. [ 2.713108@0] emmc: clock 100000000, 8-bit-bus-width
  591. [ 2.713108@0]
  592. [ 2.713108@0] mmcblk0: emmc:0001 HBG4a2 29.1 GiB
  593. [ 2.713234@0] mmcblk0boot0: emmc:0001 HBG4a2 partition 1 4.00 MiB
  594. [ 2.713354@0] mmcblk0boot1: emmc:0001 HBG4a2 partition 2 4.00 MiB
  595. [ 2.713475@0] mmcblk0rpmb: emmc:0001 HBG4a2 partition 3 4.00 MiB
  596. [ 2.714179@1] mmcblk0: unknown partition table
  597. [ 2.714734@0] [mmc_read_partition_tbl] mmc read partition OK!
  598. [ 2.714736@0] add_emmc_partition
  599. [ 2.714910@1] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
  600. [ 2.715042@0] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
  601. [ 2.715170@1] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
  602. [ 2.715292@0] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
  603. [ 2.715408@1] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
  604. [ 2.715529@0] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
  605. [ 2.715652@1] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
  606. [ 2.715795@0] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
  607. [ 2.715919@1] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
  608. [ 2.716047@0] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
  609. [ 2.716173@1] [mmcblk0p11] boot offset 0x000034400000, size 0x000002000000
  610. [ 2.716297@0] [mmcblk0p12] system offset 0x000036c00000, size 0x000080000000
  611. [ 2.716422@1] [mmcblk0p13] data offset 0x0000b7400000, size 0x000690800000
  612. [ 2.716455@1] card key: card_blk_probe.
  613. [ 2.716459@1] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
  614. [ 2.716462@1] emmc key: emmc_key_init:552 ok.
  615. [ 2.717442@0] amlmmc_dtb_init: register dtb chardev
  616. [ 2.717446@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  617. [ 2.717446@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  618. [ 2.717452@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  619. [ 2.717453@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14200, operation is in [reserved] disk!
  620. [ 2.717473@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  621. [ 2.717615@4] [aml_sd_emmc_data_thread] aml_sd_emmc_data_thread() 2658: set 1st retry!
  622. [ 2.717618@4] [aml_sd_emmc_data_thread] retry cmd 18 the 10-th time(s)
  623. [ 2.717650@4] aml_sd_emmc_data_thread : 2589
  624. [ 2.718500@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0021, virqc:3fff
  625. [ 2.718500@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  626. [ 2.718504@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  627. [ 2.718504@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14200, operation is in [reserved] disk!
  628. [ 2.718518@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  629. [ 2.718660@4] [aml_sd_emmc_data_thread] retry cmd 18 the 9-th time(s)
  630. [ 2.718689@4] aml_sd_emmc_data_thread : 2589
  631. [ 2.719559@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  632. [ 2.719559@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  633. [ 2.719565@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  634. [ 2.719565@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14200, operation is in [reserved] disk!
  635. [ 2.719590@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  636. [ 2.719732@4] [aml_sd_emmc_data_thread] retry cmd 18 the 8-th time(s)
  637. [ 2.719764@4] aml_sd_emmc_data_thread : 2589
  638. [ 2.720630@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  639. [ 2.720630@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  640. [ 2.720634@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  641. [ 2.720634@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14200, operation is in [reserved] disk!
  642. [ 2.720648@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  643. [ 2.720789@4] [aml_sd_emmc_data_thread] retry cmd 18 the 7-th time(s)
  644. [ 2.720819@4] aml_sd_emmc_data_thread : 2589
  645. [ 2.721669@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0021, virqc:3fff
  646. [ 2.721669@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  647. [ 2.721673@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  648. [ 2.721673@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14200, operation is in [reserved] disk!
  649. [ 2.721686@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  650. [ 2.721829@4] [aml_sd_emmc_data_thread] retry cmd 18 the 6-th time(s)
  651. [ 2.721858@4] aml_sd_emmc_data_thread : 2589
  652. [ 2.722705@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  653. [ 2.722705@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  654. [ 2.722709@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  655. [ 2.722709@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14200, operation is in [reserved] disk!
  656. [ 2.722723@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  657. [ 2.722863@4] [aml_sd_emmc_data_thread] retry cmd 18 the 5-th time(s)
  658. [ 2.722885@4] aml_sd_emmc_data_thread : 2589
  659. [ 2.723736@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0021, virqc:3fff
  660. [ 2.723736@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  661. [ 2.723740@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  662. [ 2.723740@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14200, operation is in [reserved] disk!
  663. [ 2.723754@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  664. [ 2.723895@4] [aml_sd_emmc_data_thread] retry cmd 18 the 4-th time(s)
  665. [ 2.723917@4] aml_sd_emmc_data_thread : 2589
  666. [ 2.724766@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0021, virqc:3fff
  667. [ 2.724766@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  668. [ 2.724770@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  669. [ 2.724770@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14200, operation is in [reserved] disk!
  670. [ 2.724784@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  671. [ 2.724928@4] [aml_sd_emmc_data_thread] retry cmd 18 the 3-th time(s)
  672. [ 2.724949@4] aml_sd_emmc_data_thread : 2589
  673. [ 2.725796@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0021, virqc:3fff
  674. [ 2.725797@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  675. [ 2.725801@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  676. [ 2.725801@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14200, operation is in [reserved] disk!
  677. [ 2.725815@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  678. [ 2.725956@4] [aml_sd_emmc_data_thread] retry cmd 18 the 2-th time(s)
  679. [ 2.725978@4] aml_sd_emmc_data_thread : 2589
  680. [ 2.726824@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  681. [ 2.726824@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  682. [ 2.726828@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  683. [ 2.726828@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14200, operation is in [reserved] disk!
  684. [ 2.726841@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  685. [ 2.726984@4] [aml_sd_emmc_data_thread] retry cmd 18 the 1-th time(s)
  686. [ 2.727007@4] aml_sd_emmc_data_thread : 2589
  687. [ 2.727852@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  688. [ 2.727853@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  689. [ 2.727857@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  690. [ 2.727857@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14200, operation is in [reserved] disk!
  691. [ 2.727871@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  692. [ 2.728012@4] [aml_sd_emmc_data_thread] Command retried failed line:2755, cmd:18
  693. [ 2.728035@4] aml_sd_emmc_data_thread : 2589
  694. [ 2.728046@1] _dtb_read: save dtb error
  695. [ 2.728046@1] _dtb_init: block # 0x14200 ERROR!
  696. [ 2.728883@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0021, virqc:3fff
  697. [ 2.728883@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  698. [ 2.728887@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  699. [ 2.728887@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
  700. [ 2.728909@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  701. [ 2.729051@4] [aml_sd_emmc_data_thread] aml_sd_emmc_data_thread() 2658: set 1st retry!
  702. [ 2.729053@4] [aml_sd_emmc_data_thread] retry cmd 18 the 10-th time(s)
  703. [ 2.729077@4] aml_sd_emmc_data_thread : 2589
  704. [ 2.729910@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  705. [ 2.729910@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  706. [ 2.729914@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  707. [ 2.729914@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
  708. [ 2.729928@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  709. [ 2.730070@4] [aml_sd_emmc_data_thread] retry cmd 18 the 9-th time(s)
  710. [ 2.730095@4] aml_sd_emmc_data_thread : 2589
  711. [ 2.730928@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  712. [ 2.730928@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  713. [ 2.730932@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  714. [ 2.730933@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
  715. [ 2.730946@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  716. [ 2.731088@4] [aml_sd_emmc_data_thread] retry cmd 18 the 8-th time(s)
  717. [ 2.731110@4] aml_sd_emmc_data_thread : 2589
  718. [ 2.731941@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  719. [ 2.731941@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  720. [ 2.731945@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  721. [ 2.731945@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
  722. [ 2.731959@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  723. [ 2.732102@4] [aml_sd_emmc_data_thread] retry cmd 18 the 7-th time(s)
  724. [ 2.732127@4] aml_sd_emmc_data_thread : 2589
  725. [ 2.732961@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  726. [ 2.732961@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  727. [ 2.732965@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  728. [ 2.732965@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
  729. [ 2.732979@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  730. [ 2.733120@4] [aml_sd_emmc_data_thread] retry cmd 18 the 6-th time(s)
  731. [ 2.733145@4] aml_sd_emmc_data_thread : 2589
  732. [ 2.733979@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  733. [ 2.733979@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  734. [ 2.733983@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  735. [ 2.733983@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
  736. [ 2.733997@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  737. [ 2.734138@4] [aml_sd_emmc_data_thread] retry cmd 18 the 5-th time(s)
  738. [ 2.734160@4] aml_sd_emmc_data_thread : 2589
  739. [ 2.734993@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  740. [ 2.734993@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  741. [ 2.734997@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  742. [ 2.734997@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
  743. [ 2.735011@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  744. [ 2.735151@4] [aml_sd_emmc_data_thread] retry cmd 18 the 4-th time(s)
  745. [ 2.735176@4] aml_sd_emmc_data_thread : 2589
  746. [ 2.736010@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  747. [ 2.736010@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  748. [ 2.736014@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  749. [ 2.736014@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
  750. [ 2.736028@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  751. [ 2.736171@4] [aml_sd_emmc_data_thread] retry cmd 18 the 3-th time(s)
  752. [ 2.736193@4] aml_sd_emmc_data_thread : 2589
  753. [ 2.737026@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  754. [ 2.737026@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  755. [ 2.737030@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  756. [ 2.737031@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
  757. [ 2.737045@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  758. [ 2.737186@4] [aml_sd_emmc_data_thread] retry cmd 18 the 2-th time(s)
  759. [ 2.737208@4] aml_sd_emmc_data_thread : 2589
  760. [ 2.738038@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  761. [ 2.738039@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  762. [ 2.738043@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  763. [ 2.738043@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
  764. [ 2.738056@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  765. [ 2.738197@4] [aml_sd_emmc_data_thread] retry cmd 18 the 1-th time(s)
  766. [ 2.738221@4] aml_sd_emmc_data_thread : 2589
  767. [ 2.739054@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xe1ff0001, virqc:3fff
  768. [ 2.739055@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0977eb868; stop 0, status 4
  769. [ 2.739059@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  770. [ 2.739059@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
  771. [ 2.739081@4] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  772. [ 2.739223@4] [aml_sd_emmc_data_thread] Command retried failed line:2755, cmd:18
  773. [ 2.739249@4] aml_sd_emmc_data_thread : 2589
  774. [ 2.739256@1] _dtb_read: save dtb error
  775. [ 2.739257@1] _dtb_init: block # 0x14000 ERROR!
  776. [ 2.739258@1] total valid 0
  777. [ 2.741024@1] amlmmc_dtb_init: register dtb chardev OK
  778. [ 2.741024@1] Exit aml_emmc_partition_ops OK.
  779. [ 2.744781@1] mmcblk0boot1: unknown partition table
  780. [ 2.747352@1] mmcblk0boot0: unknown partition table
  781. [ 2.748070@1] clear_emmc_wait_flag
  782. [ 4.106376@3] sd:pdata->caps = 7
  783. [ 4.109480@3] sd:pdata->caps2 = 0
  784. [ 4.112742@3] sd:pdata->pm_caps = 0
  785. [ 4.149118@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  786. [ 4.149273@4] [aml_is_card_insert] card OUT
  787. [ 4.149350@5] [aml_is_card_insert] card OUT
  788. [ 4.157638@3] aml_sd_emmc_probe: line 3608
  789. [ 4.162232@3] aml_sd_emmc_reg_init 1152
  790. [ 4.165502@3] get property: ocr_avail, value:0x00200080
  791. [ 4.171930@3] get property: f_min, value:400000
  792. [ 4.178034@3] get property: f_max, value:200000000
  793. [ 4.184437@3] get property: max_req_size, value:0x00020000
  794. [ 4.190898@3] get property: pinname, str:sdio
  795. [ 4.196665@3] get property: card_type, value:3
  796. [ 4.202431@3] sdio:pdata->caps = 7810f
  797. [ 4.206066@3] sdio:pdata->caps2 = 0
  798. [ 4.209533@3] sdio:pdata->pm_caps = 1
  799. [ 4.248877@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  800. [ 4.250100@3] ion_dev has 1 memory regions
  801. [ 4.253177@3] ion_dev ion_dev.25: assigned reserved memory node linux,ion-dev ok
  802. [ 4.291367@0] ion_chunk_heap_create: base 3122659328 size 67108864 align 0
  803. [ 4.306285@0] ion_carveout_heap_create: base 3055550464 size 67108864 align 0
  804. [ 4.308700@0] fb: osd_init_module
  805. [ 4.311302@0] fb: viu vsync irq: 35
  806. [ 4.314502@0] fb: failed to init reserved memory
  807. [ 4.319128@0] fb: osd_set_free_scale_mode_hw
  808. [ 4.323306@0] fb: osd_probe vinfo:ffffffc00215c338
  809. [ 4.328042@0] fb: init fbdev bpp is:32
  810. [ 4.333075@0] fb: set osd0 reverse as NONE
  811. [ 4.338878@0] fb: osd probe OK
  812. [ 4.339223@3] ge2d: ge2d_init_module
  813. [ 4.342364@3] ge2d: ge2d_dev major:240
  814. [ 4.346467@0] ge2d: vpu clock is 666660000 HZ
  815. [ 4.350410@0] ge2d: ge2d clock is 400 MHZ
  816. [ 4.354353@0] ge2d: ge2d: pdev=ffffffc0971a8800, irq=182, rstc=0xffffffc09684c340, clk=ffffffc097178000
  817. [ 4.363763@0] ge2d: mapped phy: 0xd0160000
  818. [ 4.367718@0] ge2d: ge2d start monitor
  819. [ 4.371515@1] ge2d: ge2d workqueue monitor start
  820. [ 4.371797@3] sysled: module init
  821. [ 4.371943@3] sysled: init level = 0
  822. [ 4.371945@3] sysled: led_gpio = 154
  823. [ 4.371946@3] sysled: active_low = 0
  824. [ 4.372130@0] sysled: module probed ok
  825. [ 4.372600@0] pwmled: module init
  826. [ 4.372615@0] aml_ledlight_init!
  827. [ 4.372700@0] ledlight_probe!
  828. [ 4.37273e@0] led_name: power_led
  829. [ 4.372752@0] gpio pin: 154
  830. [ 4.372755@0] gpio active: 1
  831. [ 4.372757@0] led_type: R&G
  832. [ 4.372759@0] ledlight gpio-num is 1
  833. [ 4.372761@0] ledlight_count_gpio, gpio count: 0
  834. [ 4.372763@0] ledlight_count_gpio, gpio count: 1
  835. [ 4.372765@0] set_led set pin: 154, level: 1
  836. [ 4.373054@3] codec:Amlogic A/V streaming port init
  837. [ 4.375219@3] codec:get gate demux control ok ffffffc095c3f840
  838. [ 4.375225@3] codec:get gate parser_top control ok ffffffc095c3f8c0
  839. [ 4.375229@3] codec:get gate vpu_intr control ok ffffffc095c3f940
  840. [ 4.375235@3] codec:get gate vdec control ok ffffffc095c3f9c0
  841. [ 4.376232@3] codec:[tsync_pcr_init]init success.
  842. [ 4.376262@3] codec:amvideocap_init_module
  843. [ 4.376423@3] codec:amvideocap_probe,amvideocap
  844. [ 4.376426@3] codec:use cma buf.
  845. [ 4.376428@3] codec:amvideocap_dev_register
  846. [ 4.377135@0] codec:amvdec_mmpeg4 module init
  847. [ 4.377555@3] ammvdec_h264 module init
  848. [ 4.379343@0] amvenc_avc_probe -- reserved memory config fail.
  849. [ 4.379347@0] amvenc_avc - cma memory pool size: 60 MB
  850. [ 4.379372@0] encode_wq_init.
  851. [ 4.379378@0] encode start monitor.
  852. [ 4.379442@2] encode workqueue monitor start.
  853. [ 4.379825@0] jpegenc module init
  854. [ 4.380180@2] codec:picdec_driver_probe called.
  855. [ 4.380184@2] picdec has 1 memory regions
  856. [ 4.380219@2] codec:picdec_driver_probe done.
  857. [ 4.381072@0] codec:vdec_request_irq ffffffc0017b694c, vsync
  858. [ 4.381320@2] codec:create_ge2d_work_queue video task ok
  859. [ 4.381844@0] rdma_register, rdma_table_addr ffffff8000256000 rdma_table_addr_phy b4850000 reg_buf ffffffc095e20000
  860. [ 4.381847@0] rdma_register success, handle 3 table_size 32768
  861. [ 4.381849@0] video_rdma:rdma_init video rdma handle = 3.
  862. [ 4.381854@0] codec:used fix clk for vdec clk source!
  863. [ 4.381859@0] codec:register clk_set_setting cpu[34]
  864. [ 4.382318@0] vpu_init
  865. [ 4.382520@0] vpu_probe
  866. [ 4.382525@0] HevcEnc reserved memory config fail.
  867. [ 4.382530@0] HevcEnc - cma memory pool size: 64 MB
  868. [ 4.382533@0] HevcEnc - wave420l_irq: 219
  869. [ 4.382580@0] vpu base address get from platform driver physical base addr=0xc8810000, virtual base=0xffffff80003d8000
  870. [ 4.382958@0] success to probe vpu device with video memory from cma
  871. [ 4.383264@2] DI: di_module_init ok.
  872. [ 4.383269@2] DI: di_module_init: major 233
  873. [ 4.383493@0] DI: di_probe
  874. [ 4.383615@2] deinterlace has 1 memory regions
  875. [ 4.383667@2] deinterlace deinterlace.29: assigned reserved memory node linux,di ok
  876. [ 4.383670@2] DI-di_probe: get flag_cma error.
  877. [ 4.383692@2] di_irq:78,timerc_irq:38
  878. [ 4.383835@2] rdma_register, rdma_table_addr ffffff800019c000 rdma_table_addr_phy b484a000 reg_buf ffffffc097264000
  879. [ 4.383837@2] rdma_register success, handle 4 table_size 8192
  880. [ 4.383839@2] DI: di_probe allocate rdma channel 4.
  881. [ 4.383842@2] DI: DI hw version 2.
  882. [ 4.383852@2] 0x000000db:Y=db,U=0,V=0
  883. [ 4.383853@2] 0x000000dc:Y=dc,U=0,V=0
  884. [ 4.383855@2] 0x000000dd:Y=dd,U=0,V=0
  885. [ 4.383857@2] 0x000000de:Y=de,U=0,V=0
  886. [ 4.383858@2] 0x000000df:Y=df,U=0,V=0
  887. [ 4.383860@2] 0x000000e0:Y=e0,U=0,V=0
  888. [ 4.383861@2] 0x000000e1:Y=e1,U=0,V=0
  889. [ 4.383863@2] 0x000000e2:Y=e2,U=0,V=0
  890. [ 4.383865@2] 0x000000e3:Y=e3,U=0,V=0
  891. [ 4.383868@2] 0x000000f0:Y=f0,U=0,V=0
  892. [ 4.383871@2] 0x000000f1:Y=f1,U=0,V=0
  893. [ 4.383873@2] 0x000000f2:Y=f2,U=0,V=0
  894. [ 4.383874@2] 0x000000f3:Y=f3,U=0,V=0
  895. [ 4.383876@2] 0x000000f4:Y=f4,U=0,V=0
  896. [ 4.383877@2] 0x000000f5:Y=f5,U=0,V=0
  897. [ 4.383879@2] 0x000000f6:Y=f6,U=0,V=0
  898. [ 4.383882@2] 0x000000f7:Y=f7,U=0,V=0
  899. [ 4.383884@2] 0x000000f8:Y=f8,U=0,V=0
  900. [ 4.383886@2] 0x000000f9:Y=f9,U=0,V=0
  901. [ 4.383888@2] 0x000000fa:Y=fa,U=0,V=0
  902. [ 4.383889@2] 0x000000fb:Y=fb,U=0,V=0
  903. [ 4.383891@2] 0x000000fc:Y=fc,U=0,V=0
  904. [ 4.383894@2] 0x000000fd:Y=fd,U=0,V=0
  905. [ 4.383895@2] 0x000000fe:Y=fe,U=0,V=0
  906. [ 4.383897@2] 0x000000ff:Y=ff,U=0,V=0
  907. [ 4.383899@2] DI: support multi decoding 253~254~255.
  908. [ 4.383977@2] DI: di_probe:Di use HRTIMER
  909. [ 4.384411@0] efusekeynum: 4
  910. [ 4.384420@0] efusekeyname: mac offset: 0 size: 6
  911. [ 4.384425@0] efusekeyname: mac_bt offset: 6 size: 6
  912. [ 4.384430@0] efusekeyname: mac_wifi offset: 12 size: 6
  913. [ 4.384435@0] efusekeyname: usid offset: 18 size: 16
  914. [ 4.384692@0] efuse efuse.10: probe OK!
  915. [ 4.385065@2] key unify config unifykey-num is 14
  916. [ 4.385114@2] key unify fact unifykey-num is 14
  917. [ 4.385118@2] aml_unifykeys_probe:1280=============unifykey_devno:e700000
  918. [ 4.385368@2] 6unifykey: device unifykeys created ok
  919. [ 4.385488@0] 6aml_unifykeys_init done!
  920. [ 4.385490@0] PPMGRDRV: warn: ppmgr module init func called
  921. [ 4.385615@0] PPMGRDRV: err: ppmgr_driver_probe called
  922. [ 4.385618@0] ppmgr has 1 memory regions
  923. [ 4.385659@0] PPMGRDRV: info: ppmgr_dev major:230
  924. [ 4.385895@0] PPMGRDRV: info: ppmgr_probe done
  925. [ 4.386303@0] amlogic rfkill init
  926. [ 4.386409@0] enter bt_probe of_node
  927. [ 4.386429@0] not get gpio_en
  928. [ 4.386433@0] power on valid level is high
  929. [ 4.386433@0] bt: power_on_pin_OD = 0;
  930. [ 4.386730@0] Bluetooth: BlueSleep Mode Driver Ver 1.2
  931. [ 4.387276@0] ionvideo-000: V4L2 device registered as video13
  932. [ 4.387384@2] ionvideo-001: V4L2 device registered as video14
  933. [ 4.387507@0] ionvideo-002: V4L2 device registered as video15
  934. [ 4.387622@2] ionvideo-003: V4L2 device registered as video16
  935. [ 4.387749@0] ionvideo-004: V4L2 device registered as video17
  936. [ 4.387853@2] ionvideo-005: V4L2 device registered as video18
  937. [ 4.387961@0] ionvideo-006: V4L2 device registered as video19
  938. [ 4.388072@2] ionvideo-007: V4L2 device registered as video20
  939. [ 4.388178@0] ionvideo-008: V4L2 device registered as video21
  940. [ 4.388179@0] ionvid: info: Video Technology Magazine Ion Video
  941. [ 4.388181@0] ionvid: info: Capture Board ver 1.0 successfully loaded
  942. [ 4.388190@0] audio_dsp: [dsp]register dsp to char divece(257)
  943. [ 4.388912@2] amaudio: amaudio: driver amaudio succuess!
  944. [ 4.389291@0] amlvid:info: amlvideo_init called
  945. [ 4.389292@0] amlvid:info: amlvideo_create_instance called
  946. [ 4.389296@0] amlvid:info: v4l2_dev.name=:amlvideo-000
  947. [ 4.389441@2] amlvideo-000: V4L2 device registered as video10
  948. [ 4.389801@2] vdin_drv_init: major 229
  949. [ 4.390159@0] rdma_register, rdma_table_addr ffffff80001a9000 rdma_table_addr_phy b484c000 reg_buf ffffffc095dcb800
  950. [ 4.390161@0] rdma_register success, handle 5 table_size 512
  951. [ 4.390163@0] vdin_drv_probe:vdin.0 rdma hanld 5.
  952. [ 4.390352@2]
  953. [ 4.390352@2] vdin memory resource undefined!!
  954. [ 4.390356@2] vdin0 cma_mem_size = 16 MB
  955. [ 4.390361@2] vdin0 irq: 115 rdma irq: 2
  956. [ 4.390400@2] vdin_drv_probe: fclk_div5 is 400 MHZ
  957. [ 4.390422@2] vdin_drv_probe: vdin[0] clock is 50 MHZ
  958. [ 4.390644@0] vdin_drv_probe: driver initialized ok
  959. [ 4.390765@0] rdma_register, rdma_table_addr ffffff80001ab000 rdma_table_addr_phy b484d000 reg_buf ffffffc095dcbc00
  960. [ 4.390767@0] rdma_register success, handle 6 table_size 512
  961. [ 4.390769@0] vdin_drv_probe:vdin.1 rdma hanld 6.
  962. [ 4.390929@2] vdin1 has 1 memory regions
  963. [ 4.390972@2] vdin vdin1.31: assigned reserved memory node linux,vdin1_cma ok
  964. [ 4.390973@2]
  965. [ 4.390973@2] vdin memory resource done.
  966. [ 4.390977@2] vdin1 cma_mem_size = 16 MB
  967. [ 4.390981@2] vdin1 irq: 117 rdma irq: 4
  968. [ 4.391007@2] vdin_drv_probe: fclk_div5 is 400 MHZ
  969. [ 4.391014@2] vdin_drv_probe: vdin[1] clock is 50 MHZ
  970. [ 4.391207@0] vdin_drv_probe: driver initialized ok
  971. [ 4.391381@2] vdin_drv_init: vdin driver init done
  972. [ 4.391387@2] tvafe_drv_init: major 228
  973. [ 4.391760@2] tvafe: tvafe_init.
  974. [ 4.392085@2] vbi: vbi_init.
  975. [ 4.392591@0] [RX]-hdmirx: hdmirx_init.
  976. [ 4.392595@0] ESM HLD: Initializing...
  977. [ 4.392597@0] ESM HLD: Registering device range 'esm_rx'...
  978. [ 4.392604@0] ESM HLD: Device range 'esm_rx' has been registered.
  979. [ 4.392606@0] ESM HLD: Creating class /sys/class/elliptic_rx...
  980. [ 4.392679@2] ESM HLD: The class /sys/class/elliptic_rx has been created.
  981. [ 4.392681@2] ESM HLD: Creating device 'esm_rx'...
  982. [ 4.392822@0] ESM HLD: Device 'esm_rx' has been created.
  983. [ 4.392823@0] ESM HLD: Done initializing the HLD driver.
  984. [ 4.392825@0] amvdec_656in module: init.
  985. [ 4.392827@0] amvdec_656in_init_module. 1 hardware detected!.
  986. [ 4.392831@0] amvdec_656in_init_module:major 225
  987. [ 4.393032@2] amvdec_656in_probe:start probe .
  988. [ 4.393037@2] amvdec_656in_probe: bt656 devp->index =0
  989. [ 4.393073@2] amvdec_656in_probe: bt656[0] clock is 333 MHZ
  990. [ 4.393203@0] amvdec_656in_probe:bt656[0]start get ioremap .
  991. [ 4.393218@0] amvdec_656in_probe: bt656[0] maped reg_base =ffffff80001ae000, size=7c
  992. [ 4.393221@0] amvdec_656in_probe: tvin_frontend_init done :0
  993. [ 4.393229@0] amvdec_656in probe ok.
  994. [ 4.393244@0] amvdec_656in_probe:start probe .
  995. [ 4.393247@0] amvdec_656in_probe: bt656 devp->index =1
  996. [ 4.393264@0] amvdec_656in_probe: bt656[1] clock is 333 MHZ
  997. [ 4.393373@2] amvdec_656in_probe:bt656[1]start get ioremap .
  998. [ 4.393382@2] amvdec_656in_probe: bt656[1] maped reg_base =ffffff80001ba000, size=7c
  999. [ 4.393384@2] amvdec_656in_probe: tvin_frontend_init done :1
  1000. [ 4.393390@2] amvdec_656in probe ok.
  1001. [ 4.393546@0] amvdec_656in_init_module: bt656 driver init done
  1002. [ 4.393549@0] [viuin..]viuin_init_module viuin module init
  1003. [ 4.393992@0] [viuin..]viuin_probe probe ok.
  1004. [ 4.394073@2] aml_vecm_init:module init
  1005. [ 4.394229@2]
  1006. [ 4.394229@2] VECM probe start
  1007. [ 4.394523@2] Can't find wb_sel.
  1008. [ 4.394527@2] dolby_vision_init_receiver(dvel)
  1009. [ 4.394534@2] dolby_vision_init_receiver: dvel
  1010. [ 4.394668@2] aml_vecm_probe: ok
  1011. [ 4.395440@0] saradc c1108680.saradc: initialized by BL30
  1012. [ 4.395451@0] saradc c1108680.saradc: calibration start:
  1013. [ 4.395498@0] saradc c1108680.saradc: nominal=0, value=5
  1014. [ 4.395545@0] saradc c1108680.saradc: nominal=256, value=232
  1015. [ 4.395591@0] saradc c1108680.saradc: nominal=512, value=461
  1016. [ 4.395637@0] saradc c1108680.saradc: nominal=768, value=690
  1017. [ 4.395682@0] saradc c1108680.saradc: nominal=1023, value=920
  1018. [ 4.395685@0] saradc c1108680.saradc: calibration end: coef=4578
  1019. [ 4.395892@2] remote: Driver init
  1020. [ 4.395980@2] remote: platform_data g_remote_ao_offset=580
  1021. [ 4.395983@2] remote: platform_data irq =228
  1022. [ 4.396012@2] remote: set drvdata completed
  1023.  
  1024. [ 4.396023@2] remote: device_create_file completed
  1025.  
  1026. [ 4.396316@2] input: aml_keypad as /devices/meson-remote.12/input/input0
  1027. [ 4.396570@2] remote: input_register_device completed
  1028.  
  1029. [ 4.396634@2] remote: set_remote_mode[74]
  1030. [ 4.396660@2] remote: remote config major:223
  1031.  
  1032. [ 4.396869@2] remote: physical address:0x95f48000
  1033. [ 4.397494@2] gpio-key gpio_keypad.53: gpio_key: 0 name(power) pin()
  1034. [ 4.397499@2] gpio-key gpio_keypad.53: amlogic_gpio_name_map_num pin 0!::
  1035. [ 4.397518@2] gpio-key gpio_keypad.53: gpio_key: 0 power(147)
  1036. [ 4.397559@2] gpio-key gpio_keypad.53: start setup_timer
  1037. [ 4.397566@2] gpio-key gpio_keypad.53: power key(160) registed.
  1038. [ 4.397783@0] input: gpio_keypad as /devices/gpio_keypad.53/input/input1
  1039. [ 4.397917@2] gpio-key gpio_keypad.53: gpio keypad register input device completed.
  1040. [ 4.397925@2] input input1: gpio keypad major:222
  1041. [ 4.399380@3] Sensor: lsm303d_init
  1042. [ 4.399605@2] Sensor: stk8313_init
  1043. [ 4.399687@3] Sensor: stk831x_init
  1044. [ 4.399765@2] Sensor: mxc622x_acc_init
  1045. [ 4.399841@3] Sensor: mxc6255xc_acc_init
  1046. [ 4.399993@3] Sensor: l3gd20_gyr_init
  1047. [ 4.401004@3] aml dvb init
  1048. [ 4.401470@3] Amlogic Demod DVB-T/C DebugIF Init
  1049. [ 4.401668@3] Amlogic Demod DVB-T/C DebugIF Init ok----------------
  1050. [ 4.403614@2] jtag: module init
  1051. [ 4.403832@3] jtag: pinctrl setup apao
  1052. [ 4.403834@3] jtag: set state 2
  1053. [ 4.488875@2] input input1: key 160 up
  1054. fuse_pw_en: 0x3
  1055.  
  1056. WARNING! efuse bits is disabled
  1057.  
  1058. Enable A53 JTAG cluster 0 to AO
  1059.  
  1060. [ 5.459766@0] jtag: module probed ok
  1061. [ 5.460636@2] defendkey c8834500.defendkey: defendkey_devno:d900000
  1062. [ 5.464188@3] defendkey c8834500.defendkey: defendkey: device defendkey created ok
  1063. [ 5.471693@3] defendkey: driver init
  1064. [ 5.475715@3] input: cec_input as /devices/virtual/input/input2
  1065. [ 5.481654@3] cectx aocec: no hdmirx reg resource
  1066. [ 5.485492@3] cectx aocec: no hhi reg resource
  1067. [ 5.489914@3] cec: wake up flag:0
  1068. [ 5.495227@2] aml_aes_dma c883e000.aml_aes: Aml AES_dma
  1069. [ 5.499071@2] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
  1070. [ 5.504559@3] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
  1071. [ 5.511047@3] usbcore: registered new interface driver snd-usb-audio
  1072. [ 5.518182@3] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
  1073. [ 5.525804@2] aml-i2s-dai I2S.45: I2S Mic is in platform!
  1074. [ 5.529021@2] aml_pcm_dai: pcm mode detection =1
  1075. [ 5.533658@2] aml_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4
  1076. [ 5.540368@2] aml_spdif_dai: set normal 512 fs /4 fs
  1077. [ 5.545181@2] aml_spdif_dai: set 958 audio clk div 4
  1078. [ 5.550172@2] aml_audio_hw: IEC958 16bit
  1079. [ 5.553974@2] hdmitx: audio: aout notify rate 48000
  1080. [ 5.558807@2] hdmitx: audio: aout notify size 16
  1081. [ 5.563380@2] hdmitx: audio: aout notify format CT_PCM
  1082. [ 5.569680@2] aml_snd_card: aml_multi_dev_parse_of ...
  1083. [ 5.573556@2] aml_snd_card: no multi dev!
  1084. [ 5.779166@2] aml_snd_card: headphone detection disable=1
  1085. [ 5.779210@2] aml_snd_card: no spk event delay time set
  1086. [ 5.785185@2] aml_snd_m8_card aml_m8_snd.52: T9015-audio-hifi <-> I2S.45 mapping ok
  1087. [ 5.792425@2] aml_snd_m8_card aml_m8_snd.52: dit-hifi <-> SPDIF.46 mapping ok
  1088. [ 5.798931@2] aml_pcm: enter aml_pcm_new dai->name: PCM.47 dai->id: 0
  1089. [ 5.805402@2] aml_snd_m8_card aml_m8_snd.52: pcm2bt-pcm <-> PCM.47 mapping ok
  1090. [ 5.812338@2] aml_snd_m8_card aml_m8_snd.52: ASoC: no source widget found for LOUTL
  1091. [ 5.819837@2] aml_snd_m8_card aml_m8_snd.52: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
  1092. [ 5.828649@2] aml_snd_m8_card aml_m8_snd.52: ASoC: no source widget found for LOUTR
  1093. [ 5.836222@2] aml_snd_m8_card aml_m8_snd.52: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
  1094. [ 5.847149@1] GACT probability NOT on
  1095. [ 5.848630@1] Mirror/redirect action on
  1096. [ 5.852435@1] u32 classifier
  1097. [ 5.855258@1] Actions configured
  1098. [ 5.858799@1] Netfilter messages via NETLINK v0.30.
  1099. [ 5.863698@1] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
  1100. [ 5.870389@2] ctnetlink v0.93: registering with nfnetlink.
  1101. [ 5.875850@1] xt_time: kernel timezone is -0000
  1102. [ 5.879855@1] ipip: IPv4 over IPv4 tunneling driver
  1103. [ 5.886253@1] ip_tables: (C) 2000-2006 Netfilter Core Team
  1104. [ 5.890217@1] arp_tables: (C) 2002 David S. Miller
  1105. [ 5.895655@1] TCP: cubic registered
  1106. [ 5.898211@1] Initializing XFRM netlink socket
  1107. [ 5.903604@0] NET: Registered protocol family 10
  1108. [ 5.908354@1] mip6: Mobile IPv6
  1109. [ 5.910355@1] ip6_tables: (C) 2000-2006 Netfilter Core Team
  1110. [ 5.918390@1] sit: IPv6 over IPv4 tunneling driver
  1111. [ 5.922057@1] NET: Registered protocol family 17
  1112. [ 5.925168@1] NET: Registered protocol family 15
  1113. [ 5.932238@1] Bridge firewalling registered
  1114. [ 5.933941@1] Bluetooth: Can't register RFCOMM TTY driver
  1115. [ 5.939243@1] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  1116. [ 5.944614@1] Bluetooth: BNEP filters: protocol multicast
  1117. [ 5.950145@1] Bluetooth: BNEP socket layer initialized
  1118. [ 5.955055@1] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  1119. [ 5.961101@1] Bluetooth: HIDP socket layer initialized
  1120. [ 5.966249@1] l2tp_core: L2TP core driver, V2.0
  1121. [ 5.970682@1] l2tp_ppp: PPPoL2TP kernel driver, V2.0
  1122. [ 5.975578@1] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
  1123. [ 5.981378@1] l2tp_netlink: L2TP netlink interface
  1124. [ 5.986067@1] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
  1125. [ 5.992096@1] l2tp_debugfs: L2TP debugfs support
  1126. [ 5.996623@1] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
  1127. [ 6.003244@1] NET: Registered protocol family 35
  1128. [ 6.007825@1] Key type dns_resolver registered
  1129. [ 6.014131@1] Registering SWP/SWPB emulation handler
  1130. [ 6.017764@1] Loading compiled-in X.509 certificates
  1131. [ 6.022106@1] regulator-dummy: disabling
  1132. [ 6.026486@2] aml_vrtc rtc.37: setting system clock to 2015-01-01 00:00:08 UTC (1420070408)
  1133. [ 6.036689@2] hdmirx_ext: [hdmiin_drv_init] ver: Jul042016.1
  1134. [ 6.040209@2] gxbb_pm: enter meson_pm_probe!
  1135. [ 6.044046@2] gxbb_pm: meson_pm_probe done
  1136. [ 6.049117@0] cpucore_cooling_register, max_cpu_core_num:4
  1137. [ 6.053726@0] cpucore_cooling_register, max_cpu_core_num:4
  1138. [ 6.074872@0] aml_istbt_dev_ready NULL
  1139. [ 6.074933¨²r‚ºÊºššÁ] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
  1140. [ 6.083262@0] Freeing unused kernel memory: 1340K (ffffffc001f53000 - ffffffc0020a2000)
  1141. [ 6.109134@0] init: init first stage started!
  1142. [ 6.264604@5] audit: type=1403 audit(1420070408.730:2): policy loaded auid=4294967295 ses=4294967295
  1143. [ 6.269041@5] init: (Initializing SELinux non-enforcing took 0.16s.)
  1144. [ 6.278894@5] init: init second stage started!
  1145. [ 6.286996@5] init: Running restorecon...
  1146. [ 6.383561@3] init: waitpid failed: No child processes
  1147. [ 6.383929@3] init: (Loading properties from /default.prop took 0.00s.)
  1148. [ 6.392456@3] init: (Parsing /init.environ.rc took 0.00s.)
  1149. [ 6.395738@3] init: (Parsing /init.usb.rc took 0.00s.)
  1150. [ 6.401414@3] init: /init.amlogic.rc: 269: chmod requires 2 arguments
  1151. [ 6.408602@3] init: (Parsing init.amlogic.usb.rc took 0.00s.)
  1152. [ 6.413337@3] init: (Parsing init.amlogic.usb.rc took 0.00s.)
  1153. [ 6.417926@3] init: (Parsing init.amlogic.board.rc took 0.01s.)
  1154. [ 6.424583@3] init: (Parsing init.amlogic.usb.rc took 0.00s.)
  1155. [ 6.429505@3] init: (Parsing init.amlogic.wifi.rc took 0.01s.)
  1156. [ 6.435293@3] init: could not import file 'init.mtk.rc' from '/init.amlogic.rc': No such file or directory
  1157. [ 6.444874@3] init: (Parsing /init.amlogic.rc took 0.04s.)
  1158. [ 6.451270@3] init: (Parsing /init.usb.configfs.rc took 0.00s.)
  1159. [ 6.456268@3] init: (Parsing /init.zygote32.rc took 0.00s.)
  1160. [ 6.461672@3] init: (Parsing /init.rc took 0.07s.)
  1161. [ 6.466440@3] init: aml-firstboot-init insert aml-firstboot-init
  1162. [ 6.559346@3] init: Starting service 'ueventd'...
  1163. [ 6.560846@3] init: insmod: open("/boot/optee.ko") failed: No such file or directory[ 6.562247@1] ueventd: ueventd started!
  1164. [ 6.564742@1] ueventd: coldboot /sys/class
  1165. [ 6.567970@1] ueventd: coldboot /sys/block
  1166. [ 6.568020@1] ueventd: coldboot /sys/devices/virtual/tty/console
  1167. [ 6.571203@1] ueventd: coldboot /sys/devices/virtual/tty/tty
  1168. [ 6.572176@1] ueventd: coldboot /sys/devices/virtual/tty/ptmx
  1169. [ 6.573057@1] ueventd: coldboot /sys/devices
  1170.  
  1171. [ 6.599454@3] init: insmod: open("/boot/optee_armtz.ko") failed: No such file or directoryueventd: Coldboot took 0.31s.
  1172. [ 6.875883@1] ueventd: coldboot /sys/devices/virtual/tty
  1173. [ 6.879520@1] audit: type=1400 audit(1420070409.350:3): avc: denied { relabelfrom } for pid=3136 comm="ueventd" name="tty" dev="tmpfs" ino=3108 scontext=u:r:ueventd:s0 tcontex4.899051@1] audit: type=1400 audit(1420070409.370:4): avc: denied { relabelto } for pid=3136 comm="ueventd" name="tty" dev="tmpfs" ino=3108 scontext=u:r:ueventd:s0 tcontext=u:object_r:owntty_device:s0 tclass=chr_file permissive=1
  1174. [ 6.915005@1] audit: type=1400 audit(1420070409.380:5): avc: denied { relabelfrom } for pid=3136 comm="ueventd" name="ptmx" dev="tmpfs" ino=3109 scontext=u:r:ueventd:s0 tcontext=u:object_r:ptmx_device:s0 tclass=chr_file permissive=1
  1175. [ 6.935071@1] audit: type=1400 audit(1420070409.400:6): avc: denied { relabelto } for pid=3136 comm="ueventd" name="ptmx" dev="tmpfs" ino=3109 scontext=u:r:ueventd:s0 tcontext=u:object_r:ptmx_device:s0 tclass=chr_file permissive=1
  1176. [ 6.960746@2] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
  1177. [ 6.965198@1] audit: type=1400 audit(1420070409.430:7): avc: denied { relabelfrom } for pid=3136 comm="ueventd" name="console" dev="tmpfs" ino=3107 scontext=u:r:ueventd:s0 tcontext=u:object_r:console_device:s0 tclass=chr_file permissive=1
  1178. [ 6.984974@1] audit: type=1400 audit(1420070409.450:8): avc: denied { relabelto } for pid=3136 comm="ueventd" name="console" dev="tmpfs" ino=3107 scontext=u:r:ueventd:s0 tcontext=u:object_r:console_device:s0 tclass=chr_file permissive=1
  1179. [ 7.527470@3] ueventd: Coldboot tty took 0.65s.
  1180. [ 7.595628@2] fb: afbc: 1
  1181. [ 7.596264@2] init: enter do_confirm_formated /dev/block/tee, /tee
  1182. [ 7.598765@2] init: blocksize 1024, bytes_per_inode 1024
  1183. [ 7.604177@2] init: do_confirm_formated ext4 try mount
  1184. [ 7.614599@2] EXT4-fs (mmcblk0p8): VFS: Can't find ext4 filesystem
  1185. [ 7.615350@2] init: do_confirm_formated mount fail,maybe firstboot, need format, try format now, dev:/dev/block/tee, mountpoint:/tee
  1186. [ 7.672465@2] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
  1187. [ 7.711207@3] init: enter do_confirm_formated /dev/block/data, /data
  1188. [ 7.711936@3] init: do_confirm_formated ext4 try mount
  1189. [ 7.718490@3] EXT4-fs (mmcblk0p13): VFS: Can't find ext4 filesystem
  1190. [ 7.723354@3] init: do_confirm_formated mount fail,maybe firstboot, need format, try format now, dev:/dev/block/data, mountpoint:/data
  1191. [ 9.566169@0] random: nonblocking pool is initialized
  1192. [ 10.636902@0] [aml_sd_emmc_irq] emmc: warning... data crc, vstat:0xa1ff2001, virqc:3fff
  1193. [ 10.639080@0] [aml_sd_emmc_irq] @ cmd 18 with ffffffc0970b7970; stop 0, status 4
  1194. [ 10.646577@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
  1195. [ 10.653909@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x5ba008, operation is in [data] disk!
  1196. [ 10.662219@5] aml_sd_emmc_data_thread 2642 emmc: cmd:18
  1197. [ 10.667372@5] [aml_sd_emmc_data_thread] aml_sd_emmc_data_thread() 2658: set 1st retry!
  1198. [ 10.675243@5] [aml_sd_emmc_data_thread] retry cmd 18 the 10-th time(s)
  1199. [ 10.681714@0] [aml_sd_emmc_irq] emmc: resp_timeout,vstat:0xa1ff2800,virqc:3fff
  1200. [ 10.688877@5] aml_sd_emmc_data_thread : 2589
  1201. [ 10.688966@7] emmc: req failed (CMD18): -84, retrying...
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!