Advertisement
ehj666

uMinded kernel boot log

Feb 16th, 2013
115
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 46.69 KB | None
  1. U-Boot SPL 2012.10-04268-gf925eea (Feb 05 2013 - 19:19:54)
  2. DRAM: 512MB
  3. SUNXI SD/MMC: 0
  4.  
  5.  
  6. U-Boot 2012.10-04268-gf925eea (Feb 05 2013 - 19:19:54) Allwinner Technology
  7.  
  8. CPU: SUNXI Family
  9. Board: A13-OLinuXino
  10. I2C: ready
  11. DRAM: 512 MiB
  12. MMC: SUNXI SD/MMC: 0
  13. *** Warning - bad CRC, using default environment
  14.  
  15. In: serial
  16. Out: serial
  17. Err: serial
  18. Hit any key to stop autoboot: 3  2  1  0
  19. reading uEnv.txt
  20.  
  21. ** Unable to read "uEnv.txt" from mmc 0:1 **
  22. Loading file "uEnv.txt" from mmc device 0:1
  23. Failed to mount ext2 filesystem...
  24. ** Bad ext2 partition or disk - mmc 0:1 **
  25. ext2load - load binary file from a Ext2 filesystem
  26.  
  27. Usage:
  28. ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
  29. - load binary file 'filename' from 'dev' on 'interface'
  30. to address 'addr' from ext2 filesystem
  31. Loading file "boot/uEnv.txt" from mmc device 0:1
  32. Failed to mount ext2 filesystem...
  33. ** Bad ext2 partition or disk - mmc 0:1 **
  34. ext2load - load binary file from a Ext2 filesystem
  35.  
  36. Usage:
  37. ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
  38. - load binary file 'filename' from 'dev' on 'interface'
  39. to address 'addr' from ext2 filesystem
  40. reading boot.scr
  41.  
  42. ** Unable to read "boot.scr" from mmc 0:1 **
  43. Loading file "boot.scr" from mmc device 0:1
  44. Failed to mount ext2 filesystem...
  45. ** Bad ext2 partition or disk - mmc 0:1 **
  46. ext2load - load binary file from a Ext2 filesystem
  47.  
  48. Usage:
  49. ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
  50. - load binary file 'filename' from 'dev' on 'interface'
  51. to address 'addr' from ext2 filesystem
  52. Loading file "boot/boot.scr" from mmc device 0:1
  53. Failed to mount ext2 filesystem...
  54. ** Bad ext2 partition or disk - mmc 0:1 **
  55. ext2load - load binary file from a Ext2 filesystem
  56.  
  57. Usage:
  58. ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
  59. - load binary file 'filename' from 'dev' on 'interface'
  60. to address 'addr' from ext2 filesystem
  61. reading script.bin
  62.  
  63. 28156 bytes read
  64. reading uImage
  65.  
  66. 3830172 bytes read
  67. ## Booting kernel from Legacy Image at 48000000 ...
  68. Image Name: Linux-3.0.36-r1+
  69. Image Type: ARM Linux Kernel Image (uncompressed)
  70. Data Size: 3830108 Bytes = 3.7 MiB
  71. Load Address: 40008000
  72. Entry Point: 40008000
  73. Verifying Checksum ... OK
  74. Loading Kernel Image ... OK
  75. OK
  76.  
  77. Starting kernel ...
  78.  
  79. <6>Initializing cgroup subsys cpuset
  80.  
  81. <5>Linux version 3.0.36-r1+ (uminded@uminded-desktop) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #10 PREEMPT Sat Feb 16 09:59:42 CST 2013
  82.  
  83. CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
  84.  
  85. CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
  86.  
  87. Machine: sun5i
  88.  
  89. DRAM: 512<6>Total Detected Memory: 512MB with 1 banks
  90.  
  91. <4>Ignoring unrecognised tag 0x00000000
  92.  
  93. <6>Memory Reserved(in bytes):
  94.  
  95. <6> LCD: 0x5a000000, 0x02000000
  96.  
  97. <6> SYS: 0x43000000, 0x00010000
  98.  
  99. <6> G2D: 0x58000000, 0x01000000
  100.  
  101. <6> VE : 0x44000000, 0x05000000
  102.  
  103. Memory policy: ECC disabled, Data cache writeback
  104.  
  105. <7>On node 0 totalpages: 114688
  106.  
  107. <7>free_area_init_node: node 0, pgdat c073c260, node_mem_map c08f1000
  108.  
  109. <7> Normal zone: 896 pages used for memmap
  110.  
  111. <7> Normal zone: 0 pages reserved
  112.  
  113. <7> Normal zone: 113792 pages, LIFO batch:31
  114.  
  115. <7>pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
  116.  
  117. <7>pcpu-alloc: [0] 0
  118.  
  119. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113792
  120.  
  121. <5>Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait loglevel=8 panic=10
  122.  
  123. <6>PID hash table entries: 2048 (order: 1, 8192 bytes)
  124.  
  125. <6>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  126.  
  127. <6>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  128.  
  129. <6>Memory: 448MB = 448MB total
  130.  
  131. <5>Memory: 330816k/330816k available, 127936k reserved, 0K highmem
  132.  
  133. <5>Virtual kernel memory layout:
  134.  
  135. vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  136.  
  137. fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  138.  
  139. DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
  140.  
  141. vmalloc : 0xdc800000 - 0xf0000000 ( 312 MB)
  142.  
  143. lowmem : 0xc0000000 - 0xdc000000 ( 448 MB)
  144.  
  145. pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  146.  
  147. modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  148.  
  149. .init : 0xc0008000 - 0xc0031000 ( 164 kB)
  150.  
  151. .text : 0xc0031000 - 0xc0700000 (6972 kB)
  152.  
  153. .data : 0xc0700000 - 0xc0741ab8 ( 263 kB)
  154.  
  155. .bss : 0xc0741adc - 0xc08f0840 (1724 kB)
  156.  
  157. <6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  158.  
  159. <6>NR_IRQS:96 nr_irqs:96 96
  160.  
  161. <6>timer0: Periodic Mode
  162.  
  163. <6>Console: colour dummy device 80x30
  164.  
  165. <3>ram_console: buffer (null), invalid size 0, datasize 4294967284
  166.  
  167. <6>Calibrating delay loop... <c>1001.88 BogoMIPS (lpj=5009408)
  168.  
  169. <6>pid_max: default: 32768 minimum: 301
  170.  
  171. <6>Mount-cache hash table entries: 512
  172.  
  173. <6>Initializing cgroup subsys cpuacct
  174.  
  175. <6>Initializing cgroup subsys devices
  176.  
  177. <6>Initializing cgroup subsys freezer
  178.  
  179. <6>Initializing cgroup subsys blkio
  180.  
  181. <6>CPU: Testing write buffer coherency: ok
  182.  
  183. <6>hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
  184.  
  185. <6>devtmpfs: initialized
  186.  
  187. <6>print_constraints: dummy:
  188.  
  189. <6>NET: Registered protocol family 16
  190.  
  191. <6>hw-breakpoint: debug architecture 0x4 unsupported.
  192.  
  193. SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics
  194.  
  195. <6>Initialize DMAC OK
  196.  
  197. <6>bio: create slab <bio-0> at 0
  198.  
  199. <5>SCSI subsystem initialized
  200.  
  201. <6>usbcore: registered new interface driver usbfs
  202.  
  203. <6>usbcore: registered new interface driver hub
  204.  
  205. <6>usbcore: registered new device driver usb
  206.  
  207. <6>Advanced Linux Sound Architecture Driver Version 1.0.24.
  208.  
  209. <6>cfg80211: Calling CRDA to update world regulatory domain
  210.  
  211. Init eGon pin module V2.0
  212.  
  213. <6>Switching to clocksource aw 64bits couter
  214.  
  215. <5>FS-Cache: Loaded
  216.  
  217. <6>CacheFiles: Loaded
  218.  
  219. <6>timer0: Oneshot Mode
  220.  
  221. [usb_manager]: CONFIG_USB_SW_SUN5I_USB0_OTG
  222.  
  223. [sw_hcd0]: usb host driver initialize........
  224.  
  225. [sw_hcd0]: [sw_hcd_host0]: open_usb_clock
  226.  
  227. [hcd0]: open, 0x60(0xc141), 0xcc(0x143)
  228.  
  229. [sw_hcd0]: host_init_state = 0
  230.  
  231. [sw_hcd0]: platform is usb host
  232.  
  233. [sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 38
  234.  
  235. <6>sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
  236.  
  237. <6>sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
  238.  
  239. <6>hub 1-0:1.0: USB hub found
  240.  
  241. <6>hub 1-0:1.0: 1 port detected
  242.  
  243. wrn: hcd is not enable, need not start hcd
  244.  
  245. [sw_hcd0]: sw_usb_host0_disable start
  246.  
  247. -------sw_hcd0_soft_disconnect---------
  248.  
  249. [sw_hcd_host0]: Set USB Power OFF
  250.  
  251. wrn: hcd is not enable, need not stop hcd
  252.  
  253. [sw_hcd0]: sw_usb_host0_disable end
  254.  
  255. [sw_udc]: udc_init: version 20080411
  256.  
  257. axp driver uning configuration failed(561)
  258.  
  259. axp driver uning configuration failed(573)
  260.  
  261. <6>NET: Registered protocol family 2
  262.  
  263. <6>IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
  264.  
  265. <6>TCP established hash table entries: 16384 (order: 5, 131072 bytes)
  266.  
  267. <6>TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
  268.  
  269. <6>TCP: Hash tables configured (established 16384 bind 16384)
  270.  
  271. <6>TCP reno registered
  272.  
  273. <6>UDP hash table entries: 256 (order: 0, 4096 bytes)
  274.  
  275. <6>UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  276.  
  277. <6>NET: Registered protocol family 1
  278.  
  279. <6>RPC: Registered named UNIX socket transport module.
  280.  
  281. <6>RPC: Registered udp transport module.
  282.  
  283. <6>RPC: Registered tcp transport module.
  284.  
  285. <6>RPC: Registered tcp NFSv4.1 backchannel transport module.
  286.  
  287. [pm]aw_pm_init!
  288.  
  289. <6>audit: initializing netlink socket (disabled)
  290.  
  291. <5>type=2000 audit(0.309:1): initialized
  292.  
  293. <6>ashmem: initialized
  294.  
  295. <5>VFS: Disk quotas dquot_6.5.2
  296.  
  297. Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  298.  
  299. <6>NTFS driver 2.1.30 [Flags: R/W].
  300.  
  301. <6>fuse init (API version 7.16)
  302.  
  303. <6>msgmni has been set to 646
  304.  
  305. <6>alg: No test for stdrng (krng)
  306.  
  307. <6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
  308.  
  309. <6>io scheduler noop registered
  310.  
  311. <6>io scheduler deadline registered
  312.  
  313. <6>io scheduler cfq registered (default)
  314.  
  315. <6>Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
  316.  
  317. [uart]: failed to get uart2's used information
  318.  
  319. [uart]: failed to get uart3's used information
  320.  
  321. [uart]: used uart info.: 0x02
  322.  
  323. <6>sunxi-uart.1: ttyS0 at MMIO 0x1c28400 (irq = 2) is a U6_16550A
  324.  
  325. [ 0.000000] Initializing cgroup subsys cpuset
  326. [ 0.000000] Linux version 3.0.36-r1+ (uminded@uminded-desktop) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #10 PREEMPT Sat Feb 16 09:59:42 CST 2013
  327. [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
  328. [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
  329. [ 0.000000] Machine: sun5i
  330. [ 0.000000] Total Detected Memory: 512MB with 1 banks
  331. [ 0.000000] Ignoring unrecognised tag 0x00000000
  332. [ 0.000000] Memory Reserved(in bytes):
  333. [ 0.000000] LCD: 0x5a000000, 0x02000000
  334. [ 0.000000] SYS: 0x43000000, 0x00010000
  335. [ 0.000000] G2D: 0x58000000, 0x01000000
  336. [ 0.000000] VE : 0x44000000, 0x05000000
  337. [ 0.000000] Memory policy: ECC disabled, Data cache writeback
  338. [ 0.000000] On node 0 totalpages: 114688
  339. [ 0.000000] free_area_init_node: node 0, pgdat c073c260, node_mem_map c08f1000
  340. [ 0.000000] Normal zone: 896 pages used for memmap
  341. [ 0.000000] Normal zone: 0 pages reserved
  342. [ 0.000000] Normal zone: 113792 pages, LIFO batch:31
  343. [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
  344. [ 0.000000] pcpu-alloc: [0] 0
  345. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113792
  346. [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait loglevel=8 panic=10
  347. [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
  348. [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  349. [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  350. [ 0.000000] Memory: 448MB = 448MB total
  351. [ 0.000000] Memory: 330816k/330816k available, 127936k reserved, 0K highmem
  352. [ 0.000000] Virtual kernel memory layout:
  353. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  354. [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  355. [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
  356. [ 0.000000] vmalloc : 0xdc800000 - 0xf0000000 ( 312 MB)
  357. [ 0.000000] lowmem : 0xc0000000 - 0xdc000000 ( 448 MB)
  358. [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  359. [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  360. [ 0.000000] .init : 0xc0008000 - 0xc0031000 ( 164 kB)
  361. [ 0.000000] .text : 0xc0031000 - 0xc0700000 (6972 kB)
  362. [ 0.000000] .data : 0xc0700000 - 0xc0741ab8 ( 263 kB)
  363. [ 0.000000] .bss : 0xc0741adc - 0xc08f0840 (1724 kB)
  364. [ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  365. [ 0.000000] NR_IRQS:96 nr_irqs:96 96
  366. [ 0.000000] timer0: Periodic Mode
  367. [ 0.000000] Console: colour dummy device 80x30
  368. [ 0.000000] ram_console: buffer (null), invalid size 0, datasize 4294967284
  369. [ 0.000000] Calibrating delay loop... 1001.88 BogoMIPS (lpj=5009408)
  370. [ 0.050000] pid_max: default: 32768 minimum: 301
  371. [ 0.050000] Mount-cache hash table entries: 512
  372. [ 0.060000] Initializing cgroup subsys cpuacct
  373. [ 0.060000] Initializing cgroup subsys devices
  374. [ 0.060000] Initializing cgroup subsys freezer
  375. [ 0.070000] Initializing cgroup subsys blkio
  376. [ 0.070000] CPU: Testing write buffer coherency: ok
  377. [ 0.070000] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
  378. [ 0.080000] devtmpfs: initialized
  379. [ 0.080000] print_constraints: dummy:
  380. [ 0.090000] NET: Registered protocol family 16
  381. [ 0.090000] hw-breakpoint: debug architecture 0x4 unsupported.
  382. [ 0.100000] SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics
  383. [ 0.100000] Initialize DMAC OK
  384. [ 0.110000] bio: create slab <bio-0> at 0
  385. [ 0.110000] SCSI subsystem initialized
  386. [ 0.120000] usbcore: registered new interface driver usbfs
  387. [ 0.120000] usbcore: registered new interface driver hub
  388. [ 0.120000] usbcore: registered new device driver usb
  389. [ 0.130000] Advanced Linux Sound Architecture Driver Version 1.0.24.
  390. [ 0.140000] cfg80211: Calling CRDA to update world regulatory domain
  391. [ 0.140000] Init eGon pin module V2.0
  392. [ 0.140000] Switching to clocksource aw 64bits couter
  393. [ 0.150000] FS-Cache: Loaded
  394. [ 0.150000] CacheFiles: Loaded
  395. [ 0.160000] timer0: Oneshot Mode
  396. [ 0.160000] [usb_manager]: CONFIG_USB_SW_SUN5I_USB0_OTG
  397. [ 0.160000] [sw_hcd0]: usb host driver initialize........
  398. [ 0.170000] [sw_hcd0]: [sw_hcd_host0]: open_usb_clock
  399. [ 0.170000] [hcd0]: open, 0x60(0xc141), 0xcc(0x143)
  400. [ 0.170000] [sw_hcd0]: host_init_state = 0
  401. [ 0.170000] [sw_hcd0]: platform is usb host
  402. [ 0.170000] [sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 38
  403. [ 0.180000] sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
  404. [ 0.190000] sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
  405. [ 0.190000] hub 1-0:1.0: USB hub found
  406. [ 0.190000] hub 1-0:1.0: 1 port detected
  407. [ 0.210000] wrn: hcd is not enable, need not start hcd
  408. [ 0.210000] [sw_hcd0]: sw_usb_host0_disable start
  409. [ 0.210000] -------sw_hcd0_soft_disconnect---------
  410. [ 0.210000] [sw_hcd_host0]: Set USB Power OFF
  411. [ 0.210000] wrn: hcd is not enable, need not stop hcd
  412. [ 0.220000] [sw_hcd0]: sw_usb_host0_disable end
  413. [ 0.220000] [sw_udc]: udc_init: version 20080411
  414. [ 0.220000] axp driver uning configuration failed(561)
  415. [ 0.230000] axp driver uning configuration failed(573)
  416. [ 0.240000] NET: Registered protocol family 2
  417. [ 0.240000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
  418. [ 0.240000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
  419. [ 0.250000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
  420. [ 0.260000] TCP: Hash tables configured (established 16384 bind 16384)
  421. [ 0.270000] TCP reno registered
  422. [ 0.270000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  423. [ 0.270000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  424. [ 0.280000] NET: Registered protocol family 1
  425. [ 0.280000] RPC: Registered named UNIX socket transport module.
  426. [ 0.280000] RPC: Registered udp transport module.
  427. [ 0.290000] RPC: Registered tcp transport module.
  428. [ 0.290000] RPC: Registered tcp NFSv4.1 backchannel transport module.
  429. [ 0.290000] [pm]aw_pm_init!
  430. [ 0.300000] audit: initializing netlink socket (disabled)
  431. [ 0.310000] type=2000 audit(0.309:1): initialized
  432. [ 0.320000] ashmem: initialized
  433. [ 0.320000] VFS: Disk quotas dquot_6.5.2
  434. [ 0.320000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  435. [ 0.340000] NTFS driver 2.1.30 [Flags: R/W].
  436. [ 0.340000] fuse init (API version 7.16)
  437. [ 0.350000] msgmni has been set to 646
  438. [ 0.350000] alg: No test for stdrng (krng)
  439. [ 0.350000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
  440. [ 0.360000] io scheduler noop registered
  441. [ 0.370000] io scheduler deadline registered
  442. [ 0.370000] io scheduler cfq registered (default)
  443. [ 0.370000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
  444. [ 0.380000] [uart]: failed to get uart2's used information
  445. [ 0.380000] [uart]: failed to get uart3's used information
  446. [ 0.380000] [uart]: used uart info.: 0x02
  447. [ 0.410000] sunxi-uart.1: ttyS0 at MMIO 0x1c28400 (irq = 2) is a U6_16550A
  448. <6>console [ttyS0] enabled
  449.  
  450. [ 1.060000] console [ttyS0] enabled
  451. [uart]: serial probe 1, membase (null) irq 2 mapbase 0x01c28400
  452.  
  453. [ 1.060000] [uart]: serial probe 1, membase (null) irq 2 mapbase 0x01c28400
  454. <6>brd: module loaded
  455.  
  456. [ 1.080000] brd: module loaded
  457. <6>loop: module loaded
  458.  
  459. [ 1.080000] loop: module loaded
  460. <6>usbcore: registered new interface driver ub
  461.  
  462. [ 1.090000] usbcore: registered new interface driver ub
  463. [NAND]nand driver, init.
  464.  
  465. [ 1.100000] [NAND]nand driver, init.
  466. [NAND] nand gpio_request
  467.  
  468. [ 1.110000] [NAND] nand gpio_request
  469. [NAND] nand driver version: 0x2 0x9
  470.  
  471. [ 1.110000] [NAND] nand driver version: 0x2 0x9
  472. nand interrupte register ok
  473.  
  474. [ 1.120000] nand interrupte register ok
  475. ret of NFC_ChangMode is 0
  476.  
  477. [ 1.130000] ret of NFC_ChangMode is 0
  478. dma_hdle is 0
  479.  
  480. [ 1.130000] dma_hdle is 0
  481. dma_hdle is 10000008
  482.  
  483. [ 1.140000] dma_hdle is 10000008
  484. The 0 disk name = bootloader, class name = DISK, disk size = 32768
  485.  
  486. [ 1.240000] The 0 disk name = bootloader, class name = DISK, disk size = 32768
  487. The 1 disk name = env, class name = DISK, disk size = 4096
  488.  
  489. [ 1.250000] The 1 disk name = env, class name = DISK, disk size = 4096
  490. The 2 disk name = boot, class name = DISK, disk size = 65536
  491.  
  492. [ 1.260000] The 2 disk name = boot, class name = DISK, disk size = 65536
  493. The 3 disk name = system, class name = DISK, disk size = 524288
  494.  
  495. [ 1.280000] The 3 disk name = system, class name = DISK, disk size = 524288
  496. The 4 disk name = data, class name = DISK, disk size = 1048576
  497.  
  498. [ 1.290000] The 4 disk name = data, class name = DISK, disk size = 1048576
  499. The 5 disk name = misc, class name = DISK, disk size = 2048
  500.  
  501. [ 1.300000] The 5 disk name = misc, class name = DISK, disk size = 2048
  502. The 6 disk name = recovery, class name = DISK, disk size = 65536
  503.  
  504. [ 1.310000] The 6 disk name = recovery, class name = DISK, disk size = 65536
  505. The 7 disk name = cache, class name = DISK, disk size = 524288
  506.  
  507. [ 1.330000] The 7 disk name = cache, class name = DISK, disk size = 524288
  508. The 8 disk name = UDISK, class name = DISK, disk size = 5513216
  509.  
  510. [ 1.340000] The 8 disk name = UDISK, class name = DISK, disk size = 5513216
  511. The 8 disk size = 5513216
  512.  
  513. [ 1.350000] The 8 disk size = 5513216
  514. part total count = 9
  515.  
  516. [ 1.360000] part total count = 9
  517. <6> nanda:
  518.  
  519. [ 1.360000] nanda:
  520. <6> nandb: unknown partition table
  521.  
  522. [ 1.360000] nandb: unknown partition table
  523. <6> nandc: unknown partition table
  524.  
  525. [ 1.380000] nandc: unknown partition table
  526. <6> nandd: unknown partition table
  527.  
  528. [ 1.390000] nandd: unknown partition table
  529. <6> nande: unknown partition table
  530.  
  531. [ 1.400000] nande: unknown partition table
  532. <6> nandf: unknown partition table
  533.  
  534. [ 1.410000] nandf: unknown partition table
  535. <6> nandg: unknown partition table
  536.  
  537. [ 1.420000] nandg: unknown partition table
  538. <6> nandh: unknown partition table
  539.  
  540. [ 1.430000] nandh: unknown partition table
  541. <6> nandi:
  542.  
  543. [ 1.440000] nandi:
  544. <6>benn: nand probe enter
  545.  
  546. [ 1.440000] benn: nand probe enter
  547. [NAND]nand driver, ok.
  548.  
  549. [ 1.450000] [NAND]nand driver, ok.
  550. <6>sun4i gpio driver init
  551.  
  552. [ 1.450000] sun4i gpio driver init
  553. [spi]: sw spi init !!
  554.  
  555. [ 1.460000] [spi]: sw spi init !!
  556. [spi]: sw spi init fetch spi0 uning configuration failed
  557.  
  558. [ 1.470000] [spi]: sw spi init fetch spi0 uning configuration failed
  559. [spi]: Get spi devices number failed
  560.  
  561. [ 1.480000] [spi]: Get spi devices number failed
  562. [spi]: register spi devices board info failed
  563.  
  564. [ 1.490000] [spi]: register spi devices board info failed
  565. [spi]: drivers/spi/spi_sunxi.c(L1871) [ 1.500000] [spi]: drivers/spi/spi_sunxi.c(L1871) get spi 2 para failed, err code = -4
  566.  
  567. get spi 2 para failed, err code = -4
  568. [spi]: source = sdram_pll_p, src_clk = 408000000, mclk 102000000
  569.  
  570. [ 1.510000] [spi]: source = sdram_pll_p, src_clk = 408000000, mclk 102000000
  571. [spi]: allwinners SoC SPI Driver loaded for Bus SPI-2 with 1 Slaves attached
  572.  
  573. [ 1.530000] [spi]: allwinners SoC SPI Driver loaded for Bus SPI-2 with 1 Slaves attached
  574. [spi]: [spi-2]: driver probe succeed, base dc8aa000, irq 12, dma_id 2!
  575.  
  576. [ 1.540000] [spi]: [spi-2]: driver probe succeed, base dc8aa000, irq 12, dma_id 2!
  577. <6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  578.  
  579. [ 1.550000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  580. <6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  581.  
  582. [ 1.570000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  583.  
  584.  
  585. ------sw-ehci1 config------
  586.  
  587. [ 1.580000]
  588. [ 1.580000] ------sw-ehci1 config------
  589. hci_name = sw-ehci1
  590.  
  591. [ 1.590000] hci_name = sw-ehci1
  592. irq_no = 39
  593.  
  594. [ 1.590000] irq_no = 39
  595. usbc_no = 1
  596.  
  597. [ 1.600000] usbc_no = 1
  598. usb_vbase = 0xf1c14000
  599.  
  600. [ 1.610000] usb_vbase = 0xf1c14000
  601. sram_vbase = 0xf1c00000
  602.  
  603. [ 1.610000] sram_vbase = 0xf1c00000
  604. clock_vbase = 0xf1c20000
  605.  
  606. [ 1.620000] clock_vbase = 0xf1c20000
  607. sdram_vbase = 0xf1c01000
  608.  
  609. [ 1.630000] sdram_vbase = 0xf1c01000
  610. used = 1
  611.  
  612. [ 1.640000] used = 1
  613. host_init_state = 1
  614.  
  615. [ 1.640000] host_init_state = 1
  616. gpio_name = usb_drv_vbus_gpio
  617.  
  618. [ 1.650000] gpio_name = usb_drv_vbus_gpio
  619. port = 7
  620.  
  621. [ 1.660000] port = 7
  622. port_num = 11
  623.  
  624. [ 1.660000] port_num = 11
  625. mul_sel = 1
  626.  
  627. [ 1.670000] mul_sel = 1
  628. pull = 0
  629.  
  630. [ 1.670000] pull = 0
  631. drv_level = -1
  632.  
  633. [ 1.680000] drv_level = -1
  634. data = 0
  635.  
  636. [ 1.680000] data = 0
  637.  
  638.  
  639. --------------------------
  640.  
  641. [ 1.690000]
  642. [ 1.690000] --------------------------
  643.  
  644.  
  645. ------sw-ohci1 config------
  646.  
  647. [ 1.700000]
  648. [ 1.700000] ------sw-ohci1 config------
  649. hci_name = sw-ohci1
  650.  
  651. [ 1.710000] hci_name = sw-ohci1
  652. irq_no = 64
  653.  
  654. [ 1.710000] irq_no = 64
  655. usbc_no = 1
  656.  
  657. [ 1.720000] usbc_no = 1
  658. usb_vbase = 0xf1c14000
  659.  
  660. [ 1.730000] usb_vbase = 0xf1c14000
  661. sram_vbase = 0xf1c00000
  662.  
  663. [ 1.730000] sram_vbase = 0xf1c00000
  664. clock_vbase = 0xf1c20000
  665.  
  666. [ 1.740000] clock_vbase = 0xf1c20000
  667. sdram_vbase = 0xf1c01000
  668.  
  669. [ 1.750000] sdram_vbase = 0xf1c01000
  670. used = 1
  671.  
  672. [ 1.760000] used = 1
  673. host_init_state = 1
  674.  
  675. [ 1.760000] host_init_state = 1
  676. gpio_name = usb_drv_vbus_gpio
  677.  
  678. [ 1.770000] gpio_name = usb_drv_vbus_gpio
  679. port = 7
  680.  
  681. [ 1.770000] port = 7
  682. port_num = 11
  683.  
  684. [ 1.780000] port_num = 11
  685. mul_sel = 1
  686.  
  687. [ 1.790000] mul_sel = 1
  688. pull = 0
  689.  
  690. [ 1.790000] pull = 0
  691. drv_level = -1
  692.  
  693. [ 1.800000] drv_level = -1
  694. data = 0
  695.  
  696. [ 1.800000] data = 0
  697.  
  698.  
  699. --------------------------
  700.  
  701. [ 1.810000]
  702. [ 1.810000] --------------------------
  703. [sw-ehci1]: probe, pdev->name: sw-ehci, pdev->id: 1, sw_ehci: 0xc07e8484
  704.  
  705. [ 1.820000] [sw-ehci1]: probe, pdev->name: sw-ehci, pdev->id: 1, sw_ehci: 0xc07e8484
  706. [hcd1]: open, 0x60(0x40e147), 0xcc(0x143)
  707.  
  708. [ 1.830000] [hcd1]: open, 0x60(0x40e147), 0xcc(0x143)
  709. [sw-ehci1]: sw_set_vbus cnt 0
  710.  
  711. [ 1.840000] [sw-ehci1]: sw_set_vbus cnt 0
  712. [sw-ehci1]: Set USB Power ON
  713.  
  714. [ 1.850000] [sw-ehci1]: Set USB Power ON
  715. <6>sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  716.  
  717. [ 1.850000] sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  718. <6>sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
  719.  
  720. [ 1.870000] sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
  721. <6>sw-ehci sw-ehci.1: irq 39, io mem 0xf1c14000
  722.  
  723. [ 1.880000] sw-ehci sw-ehci.1: irq 39, io mem 0xf1c14000
  724. <6>sw-ehci sw-ehci.1: USB 0.0 started, EHCI 1.00
  725.  
  726. [ 1.910000] sw-ehci sw-ehci.1: USB 0.0 started, EHCI 1.00
  727. ehci_irq: port change detect
  728.  
  729. [ 1.920000] ehci_irq: port change detect
  730. <6>hub 2-0:1.0: USB hub found
  731.  
  732. [ 1.930000] hub 2-0:1.0: USB hub found
  733. <6>hub 2-0:1.0: 1 port detected
  734.  
  735. [ 1.930000] hub 2-0:1.0: 1 port detected
  736. [sw-ohci1]: probe, pdev->name: sw-ohci, pdev->id: 1, sw_ohci: 0xc07e8594
  737.  
  738. [ 1.940000] [sw-ohci1]: probe, pdev->name: sw-ohci, pdev->id: 1, sw_ohci: 0xc07e8594
  739. [hcd1]: open, 0x60(0x40e147), 0xcc(0x143)
  740.  
  741. [ 1.960000] [hcd1]: open, 0x60(0x40e147), 0xcc(0x143)
  742. [sw-ohci1]: sw_set_vbus cnt 1
  743.  
  744. [ 1.970000] [sw-ohci1]: sw_set_vbus cnt 1
  745. <6>sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
  746.  
  747. [ 1.970000] sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
  748. <6>sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
  749.  
  750. [ 1.990000] sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
  751. <6>sw-ohci sw-ohci.1: irq 64, io mem 0xf1c14400
  752.  
  753. [ 2.000000] sw-ohci sw-ohci.1: irq 64, io mem 0xf1c14400
  754. <6>hub 3-0:1.0: USB hub found
  755.  
  756. [ 2.060000] hub 3-0:1.0: USB hub found
  757. <6>hub 3-0:1.0: 1 port detected
  758.  
  759. [ 2.070000] hub 3-0:1.0: 1 port detected
  760. <6>Initializing USB Mass Storage driver...
  761.  
  762. [ 2.070000] Initializing USB Mass Storage driver...
  763. <6>usbcore: registered new interface driver usb-storage
  764.  
  765. [ 2.070000] usbcore: registered new interface driver usb-storage
  766. <6>USB Mass Storage support registered.
  767.  
  768. [ 2.090000] USB Mass Storage support registered.
  769. <6>usbcore: registered new interface driver ums-alauda
  770.  
  771. [ 2.090000] usbcore: registered new interface driver ums-alauda
  772. <6>usbcore: registered new interface driver ums-cypress
  773.  
  774. [ 2.110000] usbcore: registered new interface driver ums-cypress
  775. <6>usbcore: registered new interface driver ums-datafab
  776.  
  777. [ 2.120000] usbcore: registered new interface driver ums-datafab
  778. <6>usbcore: registered new interface driver ums_eneub6250
  779.  
  780. [ 2.130000] usbcore: registered new interface driver ums_eneub6250
  781. <6>usbcore: registered new interface driver ums-freecom
  782.  
  783. [ 2.150000] usbcore: registered new interface driver ums-freecom
  784. <6>usbcore: registered new interface driver ums-isd200
  785.  
  786. [ 2.160000] usbcore: registered new interface driver ums-isd200
  787. <6>usbcore: registered new interface driver ums-jumpshot
  788.  
  789. [ 2.170000] usbcore: registered new interface driver ums-jumpshot
  790. <6>usbcore: registered new interface driver ums-karma
  791.  
  792. [ 2.180000] usbcore: registered new interface driver ums-karma
  793. <6>usbcore: registered new interface driver ums-onetouch
  794.  
  795. [ 2.190000] usbcore: registered new interface driver ums-onetouch
  796. <6>usbcore: registered new interface driver ums-realtek
  797.  
  798. [ 2.200000] usbcore: registered new interface driver ums-realtek
  799. <6>usbcore: registered new interface driver ums-sddr09
  800.  
  801. [ 2.210000] usbcore: registered new interface driver ums-sddr09
  802. <6>usbcore: registered new interface driver ums-sddr55
  803.  
  804. [ 2.220000] usbcore: registered new interface driver ums-sddr55
  805. <6>usbcore: registered new interface driver ums-usbat
  806.  
  807. [ 2.230000] usbcore: registered new interface driver ums-usbat
  808. ------print_msc_config-----
  809.  
  810. [ 2.240000] ------print_msc_config-----
  811. vendor_id = 0x18d1
  812.  
  813. [ 2.250000] vendor_id = 0x18d1
  814. mass_storage_id = 0x1
  815.  
  816. [ 2.260000] mass_storage_id = 0x1
  817. adb_id = 0x2
  818.  
  819. [ 2.260000] adb_id = 0x2
  820. <6>usb 2-1: new high speed USB device number 2 using sw-ehci
  821.  
  822. [ 2.270000] usb 2-1: new high speed USB device number 2 using sw-ehci
  823. usb_manufacturer_name = USB Developer
  824.  
  825. [ 2.280000] usb_manufacturer_name = USB Developer
  826. usb_product_name = Android
  827.  
  828. [ 2.290000] usb_product_name = Android
  829. usb_serial_number = 20080411
  830.  
  831. [ 2.300000] usb_serial_number = 20080411
  832. msc_vendor_name = USB 2.0
  833.  
  834. [ 2.300000] msc_vendor_name = USB 2.0
  835. msc_product_name = USB Flash Driver
  836.  
  837. [ 2.310000] msc_product_name = USB Flash Driver
  838. msc_release = 100
  839.  
  840. [ 2.310000] msc_release = 100
  841. luns = 3
  842.  
  843. [ 2.330000] luns = 3
  844. ---------------------------
  845.  
  846. [ 2.330000] ---------------------------
  847. [sw_udc]: [ 2.340000] [sw_udc]: [sw_usb_udc]: binding gadget driver 'android_usb'
  848.  
  849. [sw_usb_udc]: binding gadget driver 'android_usb'
  850. [sw_udc]: [ 2.350000] [sw_udc]: alloc request: ep(0xc0728600, ep0, 64), req(0xd99fbbc0)
  851.  
  852. alloc request: ep(0xc0728600, ep0, 64), req(0xd99fbbc0)
  853. WRN:L2675(drivers/usb/sun5i_usb/udc/sw_udc.c):[ 2.360000] WRN:L2675(drivers/usb/sun5i_usb/udc/sw_udc.c):ERR: usb device is not active
  854.  
  855. ERR: usb device is not active
  856. [sw_udc]: [ 2.380000] [sw_udc]: sw_udc_pullup, is_on = 0
  857.  
  858. sw_udc_pullup, is_on = 0
  859. WRN:L2710(drivers/usb/sun5i_usb/udc/sw_udc.c):[ 2.380000] WRN:L2710(drivers/usb/sun5i_usb/udc/sw_udc.c):ERR: usb device is not active
  860.  
  861. ERR: usb device is not active
  862. <6>android_usb gadget: Mass Storage Function, version: 2009/09/11
  863.  
  864. [ 2.400000] android_usb gadget: Mass Storage Function, version: 2009/09/11
  865. <6>android_usb gadget: Number of LUNs=3
  866.  
  867. [ 2.420000] android_usb gadget: Number of LUNs=3
  868. <6> lun0: LUN: removable file: (no medium)
  869.  
  870. [ 2.420000] lun0: LUN: removable file: (no medium)
  871. <6> lun1: LUN: removable file: (no medium)
  872.  
  873. [ 2.420000] lun1: LUN: removable file: (no medium)
  874. <6> lun2: LUN: removable file: (no medium)
  875.  
  876. [ 2.440000] lun2: LUN: removable file: (no medium)
  877. lun name: lun
  878.  
  879. [ 2.450000] lun name: lun
  880. lun name: lun1
  881.  
  882. [ 2.450000] lun name: lun1
  883. lun name: lun2
  884.  
  885. [ 2.460000] lun name: lun2
  886. <4>Gadget Android: controller 'sw_usb_udc' not recognized
  887.  
  888. [ 2.460000] Gadget Android: controller 'sw_usb_udc' not recognized
  889. <6>android_usb gadget: android_usb ready
  890.  
  891. [ 2.470000] android_usb gadget: android_usb ready
  892. <6>mousedev: PS/2 mouse device common for all mice
  893.  
  894. [ 2.480000] mousedev: PS/2 mouse device common for all mice
  895. <6>hub 2-1:1.0: USB hub found
  896.  
  897. [ 2.490000] hub 2-1:1.0: USB hub found
  898. ========RTC Inital ===================
  899.  
  900. [ 2.490000] ========RTC Inital ===================
  901. <6>hub 2-1:1.0: 4 ports detected
  902.  
  903. [ 2.510000] hub 2-1:1.0: 4 ports detected
  904. rtc_fetch_sysconfig_para: after: rtc_twi_addr is 0x51, dirty_addr_buf: 0x51. dirty_addr_buf[1]: 0xfffe
  905.  
  906. [ 2.510000] rtc_fetch_sysconfig_para: after: rtc_twi_addr is 0x51, dirty_addr_buf: 0x51. dirty_addr_buf[1]: 0xfffe
  907. rtc_fetch_sysconfig_para: rtc_twi_id is 1.
  908.  
  909. [ 2.530000] rtc_fetch_sysconfig_para: rtc_twi_id is 1.
  910. rtc_fetch_sysconfig_para:ok
  911.  
  912. [ 2.540000] rtc_fetch_sysconfig_para:ok
  913. pcf8563_init: after fetch_sysconfig_para: normal_i2c: 0x51. normal_i2c[1]: 0xfffe
  914.  
  915. [ 2.550000] pcf8563_init: after fetch_sysconfig_para: normal_i2c: 0x51. normal_i2c[1]: 0xfffe
  916. <6>i2c /dev entries driver
  917.  
  918. [ 2.570000] i2c /dev entries driver
  919. !!! base_Addr = 0xdc8acc00
  920.  
  921. [ 2.570000] !!! base_Addr = 0xdc8acc00
  922. config i2c gpio with gpio_config api
  923.  
  924. [ 2.580000] config i2c gpio with gpio_config api
  925. twi0, apb clock = 24000000
  926.  
  927. [ 2.590000] twi0, apb clock = 24000000
  928. <6>axp_mfd 0-0034: AXP (CHIP ID: 0x21) detected
  929.  
  930. [ 2.590000] axp_mfd 0-0034: AXP (CHIP ID: 0x21) detected
  931. [AXP]axp driver uning configuration failed(323)
  932.  
  933. [ 2.600000] [AXP]axp driver uning configuration failed(323)
  934. [AXP]power_start = 0
  935.  
  936. [ 2.620000] [AXP]power_start = 0
  937. rtc_detect,line:156,twi_id:1,adapter->nr:0
  938.  
  939. [ 2.620000] rtc_detect,line:156,twi_id:1,adapter->nr:0
  940. rtc_detect,line:165
  941.  
  942. [ 2.630000] rtc_detect,line:165
  943. <6>I2C: i2c-0: AW16XX I2C adapter
  944.  
  945. [ 2.630000] I2C: i2c-0: AW16XX I2C adapter
  946. **********start************
  947.  
  948. [ 2.640000] **********start************
  949. 0x40
  950.  
  951. [ 2.640000] 0x40
  952. 0xf8
  953.  
  954. [ 2.640000] 0xf8
  955. 0x28
  956.  
  957. [ 2.650000] 0x28
  958. 0x0
  959.  
  960. [ 2.650000] 0x0
  961. 0x0
  962.  
  963. [ 2.650000] 0x0
  964. **********end************
  965.  
  966. [ 2.650000] **********end************
  967. !!! base_Addr = 0xdc8ae000
  968.  
  969. [ 2.670000] !!! base_Addr = 0xdc8ae000
  970. twi1, apb clock = 24000000
  971.  
  972. [ 2.670000] twi1, apb clock = 24000000
  973. rtc_detect,line:156,twi_id:1,adapter->nr:1
  974.  
  975. [ 2.680000] rtc_detect,line:156,twi_id:1,adapter->nr:1
  976. <6>rtc_detect: Detected chip pcf8563 at adapter 1, address 0x51
  977.  
  978. [ 2.690000] rtc_detect: Detected chip pcf8563 at adapter 1, address 0x51
  979. rtc_detect,line:161
  980.  
  981. [ 2.700000] rtc_detect,line:161
  982. pcf8563_probe,line:656
  983.  
  984. [ 2.710000] pcf8563_probe,line:656
  985. <6>pcf8563 1-0051: chip found, driver version 0.4.3
  986.  
  987. [ 2.710000] pcf8563 1-0051: chip found, driver version 0.4.3
  988. pcf8563_get_datetime,raw data is st1=08, st2=00, sec=12, min=22, hr=19, mday=16, wday=12, mon=02, year=03
  989.  
  990. [ 2.720000] pcf8563_get_datetime,raw data is st1=08, st2=00, sec=12, min=22, hr=19, mday=16, wday=12, mon=02, year=03
  991. pcf8563_get_datetime: tm is secs=12, mins=22, hours=19,mday=16, mon=1, year=113, wday=2
  992.  
  993. [ 2.740000] pcf8563_get_datetime: tm is secs=12, mins=22, hours=19,mday=16, mon=1, year=113, wday=2
  994. <6>using rtc device, pcf8563, for alarms[ 2.760000] using rtc device, pcf8563, for alarms<6>pcf8563 1-0051: rtc core: registered pcf8563 as rtc0
  995. [ 2.760000] pcf8563 1-0051: rtc core: registered pcf8563 as rtc0
  996. <6>I2C: i2c-1: AW16XX I2C adapter
  997.  
  998. [ 2.780000] I2C: i2c-1: AW16XX I2C adapter
  999. **********start************
  1000.  
  1001. [ 2.790000] **********start************
  1002. 0x40
  1003.  
  1004. [ 2.790000] 0x40
  1005. 0xf8
  1006.  
  1007. [ 2.790000] 0xf8
  1008. 0x58
  1009.  
  1010. [ 2.800000] 0x58
  1011. 0x0
  1012.  
  1013. [ 2.800000] 0x0
  1014. 0x0
  1015.  
  1016. [ 2.800000] 0x0
  1017. **********end************
  1018.  
  1019. [ 2.800000] **********end************
  1020. !!! base_Addr = 0xdc8b0400
  1021.  
  1022. [ 2.810000] !!! base_Addr = 0xdc8b0400
  1023. twi2, apb clock = 24000000
  1024.  
  1025. [ 2.820000] twi2, apb clock = 24000000
  1026. rtc_detect,line:156,twi_id:1,adapter->nr:2
  1027.  
  1028. [ 2.820000] rtc_detect,line:156,twi_id:1,adapter->nr:2
  1029. rtc_detect,line:165
  1030.  
  1031. [ 2.830000] rtc_detect,line:165
  1032. <6>I2C: i2c-2: AW16XX I2C adapter
  1033.  
  1034. [ 2.840000] I2C: i2c-2: AW16XX I2C adapter
  1035. **********start************
  1036.  
  1037. [ 2.850000] **********start************
  1038. 0x40
  1039.  
  1040. [ 2.850000] 0x40
  1041. 0xf8
  1042.  
  1043. [ 2.850000] 0xf8
  1044. 0x58
  1045.  
  1046. [ 2.860000] 0x58
  1047. 0x0
  1048.  
  1049. [ 2.860000] 0x0
  1050. 0x0
  1051.  
  1052. [ 2.860000] 0x0
  1053. **********end************
  1054.  
  1055. [ 2.860000] **********end************
  1056. <6>lirc_dev: IR Remote Control driver registered, major 250
  1057.  
  1058. [ 2.870000] lirc_dev: IR Remote Control driver registered, major 250
  1059. <6>IR NEC protocol handler initialized
  1060.  
  1061. [ 2.880000] IR NEC protocol handler initialized
  1062. <6>IR RC5(x) protocol handler initialized
  1063.  
  1064. [ 2.880000] IR RC5(x) protocol handler initialized
  1065. <6>IR RC6 protocol handler initialized
  1066.  
  1067. [ 2.900000] IR RC6 protocol handler initialized
  1068. <6>IR JVC protocol handler initialized
  1069.  
  1070. [ 2.910000] IR JVC protocol handler initialized
  1071. <6>IR Sony protocol handler initialized
  1072.  
  1073. [ 2.910000] IR Sony protocol handler initialized
  1074. <6>IR RC5 (streamzap) protocol handler initialized
  1075.  
  1076. [ 2.910000] IR RC5 (streamzap) protocol handler initialized
  1077. <6>IR LIRC bridge handler initialized
  1078.  
  1079. [ 2.930000] IR LIRC bridge handler initialized
  1080. <6>usb 2-1.1: new low speed USB device number 3 using sw-ehci
  1081.  
  1082. [ 2.940000] usb 2-1.1: new low speed USB device number 3 using sw-ehci
  1083. [cedar dev]: install start!!!
  1084.  
  1085. [ 2.950000] [cedar dev]: install start!!!
  1086. [cedar dev]: install end!!!
  1087.  
  1088. [ 2.960000] [cedar dev]: install end!!!
  1089. [pa_drv] start!!!
  1090.  
  1091. [ 2.960000] [pa_drv] start!!!
  1092. [pa_drv] init end!!!
  1093.  
  1094. [ 2.970000] [pa_drv] init end!!!
  1095. <6>print_constraints: axp20_ldo1: 1300 mV
  1096.  
  1097. [ 2.980000] print_constraints: axp20_ldo1: 1300 mV
  1098. <6>print_constraints: axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
  1099.  
  1100. [ 2.990000] print_constraints: axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
  1101. <6>print_constraints: axp20_ldo3: 700 <--> 3500 mV at 3300 mV
  1102.  
  1103. [ 3.000000] print_constraints: axp20_ldo3: 700 <--> 3500 mV at 3300 mV
  1104. <6>print_constraints: axp20_ldo4: 1250 <--> 3300 mV at 3300 mV
  1105.  
  1106. [ 3.010000] print_constraints: axp20_ldo4: 1250 <--> 3300 mV at 3300 mV
  1107. <6>print_constraints: axp20_buck2: 700 <--> 2275 mV at 1400 mV
  1108.  
  1109. [ 3.030000] print_constraints: axp20_buck2: 700 <--> 2275 mV at 1400 mV
  1110. <6>print_constraints: axp20_buck3: 700 <--> 3500 mV at 1200 mV
  1111.  
  1112. [ 3.040000] print_constraints: axp20_buck3: 700 <--> 3500 mV at 1200 mV
  1113. <6>print_constraints: axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
  1114.  
  1115. [ 3.050000] print_constraints: axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
  1116. <6>input: axp20-supplyer as /devices/platform/sun5i-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0
  1117.  
  1118. [ 3.070000] input: axp20-supplyer as /devices/platform/sun5i-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0
  1119. <6>md: linear personality registered for level -1
  1120.  
  1121. [ 3.100000] md: linear personality registered for level -1
  1122. <6>md: multipath personality registered for level -4
  1123.  
  1124. [ 3.110000] md: multipath personality registered for level -4
  1125. <6>md: faulty personality registered for level -5
  1126.  
  1127. [ 3.120000] md: faulty personality registered for level -5
  1128. <6>device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
  1129.  
  1130. [ 3.130000] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
  1131. <6>device-mapper: multipath: version 1.3.0 loaded
  1132.  
  1133. [ 3.150000] device-mapper: multipath: version 1.3.0 loaded
  1134. <6>device-mapper: multipath round-robin: version 1.0.0 loaded
  1135.  
  1136. [ 3.160000] device-mapper: multipath round-robin: version 1.0.0 loaded
  1137. <6>device-mapper: multipath queue-length: version 0.1.0 loaded
  1138.  
  1139. [ 3.170000] device-mapper: multipath queue-length: version 0.1.0 loaded
  1140. <6>device-mapper: multipath service-time: version 0.2.0 loaded
  1141.  
  1142. [ 3.180000] device-mapper: multipath service-time: version 0.2.0 loaded
  1143. [mmc_pm]: no sdio card used in configuration
  1144.  
  1145. [ 3.200000] [mmc_pm]: no sdio card used in configuration
  1146. [mmc]: sunximmc_init
  1147.  
  1148. [ 3.200000] [mmc]: sunximmc_init
  1149. [mmc]: sunxi mmc controller using config : 0x1
  1150.  
  1151. [ 3.210000] [mmc]: sunxi mmc controller using config : 0x1
  1152. [mmc]: sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0
  1153.  
  1154. [ 3.220000] [mmc]: sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0
  1155. [mmc]: mmc 0 power off !!
  1156.  
  1157. [ 3.230000] [mmc]: mmc 0 power off !!
  1158. [mmc]: mmc0 Probe: base:0xdc8b6000 irq:32 dma:0 pdes:0xd9a8c000, ret 0.
  1159.  
  1160. [ 3.240000] [mmc]: mmc0 Probe: base:0xdc8b6000 irq:32 dma:0 pdes:0xd9a8c000, ret 0.
  1161. <6>input: DELL DELL USB Keyboard as /devices/platform/sw-ehci.1/usb2/2-1/2-1.1/2-1.1:1.0/input/input1
  1162.  
  1163. [ 3.250000] input: DELL DELL USB Keyboard as /devices/platform/sw-ehci.1/usb2/2-1/2-1.1/2-1.1:1.0/input/input1
  1164. <6>generic-usb 0003:413C:2005.0001: input: USB HID v1.10 Keyboard [DELL DELL USB Keyboard] on usb-sw-ehci-1.1/input0
  1165.  
  1166. [ 3.280000] generic-usb 0003:413C:2005.0001: input: USB HID v1.10 Keyboard [DELL DELL USB Keyboard] on usb-sw-ehci-1.1/input0
  1167. <6>usbcore: registered new interface driver usbhid
  1168.  
  1169. [ 3.300000] usbcore: registered new interface driver usbhid
  1170. <6>usbhid: USB HID core driver
  1171.  
  1172. [ 3.310000] usbhid: USB HID core driver
  1173. <6>usb 2-1.2: new low speed USB device number 4 using sw-ehci
  1174.  
  1175. [ 3.310000] usb 2-1.2: new low speed USB device number 4 using sw-ehci
  1176. <6>logger: created 256K log 'log_main'
  1177.  
  1178. [ 3.330000] logger: created 256K log 'log_main'
  1179. <6>logger: created 256K log 'log_events'
  1180.  
  1181. [ 3.340000] logger: created 256K log 'log_events'
  1182. <6>logger: created 256K log 'log_radio'
  1183.  
  1184. [ 3.340000] logger: created 256K log 'log_radio'
  1185. <6>logger: created 256K log 'log_system'
  1186.  
  1187. [ 3.350000] logger: created 256K log 'log_system'
  1188. enter sun5i Audio codec!!!
  1189.  
  1190. [ 3.360000] enter sun5i Audio codec!!!
  1191. <6>sun5i audio support initialized
  1192.  
  1193. [ 3.360000] sun5i audio support initialized
  1194. sun5i Audio codec successfully loaded..
  1195.  
  1196. [ 3.380000] sun5i Audio codec successfully loaded..
  1197. <6>ALSA device list:
  1198.  
  1199. [ 3.380000] ALSA device list:
  1200. <6> #0: sun5i-CODEC Audio Codec
  1201.  
  1202. [ 3.390000] #0: sun5i-CODEC Audio Codec
  1203. <6>IPv4 over IPv4 tunneling driver
  1204.  
  1205. [ 3.400000] IPv4 over IPv4 tunneling driver
  1206. <6>TCP cubic registered
  1207.  
  1208. [ 3.400000] TCP cubic registered
  1209. <6>Initializing XFRM netlink socket
  1210.  
  1211. [ 3.400000] Initializing XFRM netlink socket
  1212. <6>NET: Registered protocol family 17
  1213.  
  1214. [ 3.420000] NET: Registered protocol family 17
  1215. <6>NET: Registered protocol family 15
  1216.  
  1217. [ 3.430000] NET: Registered protocol family 15
  1218. <6>802.1Q VLAN Support v1.8
  1219.  
  1220. [ 3.430000] 802.1Q VLAN Support v1.8
  1221. <6>VFP support v0.3: [ 3.440000] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
  1222.  
  1223. implementor 41 architecture 3 part 30 variant c rev 3
  1224. <5>Registering SWP/SWPB emulation handler
  1225.  
  1226. [ 3.450000] Registering SWP/SWPB emulation handler
  1227. <6>registered taskstats version 1
  1228.  
  1229. [ 3.460000] registered taskstats version 1
  1230. <4>[LCD] [ 3.470000] [LCD] lcd_module_init
  1231.  
  1232. lcd_module_init
  1233. <6>input: Dell Dell USB Mouse as /devices/platform/sw-ehci.1/usb2/2-1/2-1.2/2-1.2:1.0/input/input2
  1234.  
  1235. [ 3.490000] input: Dell Dell USB Mouse as /devices/platform/sw-ehci.1/usb2/2-1/2-1.2/2-1.2:1.0/input/input2
  1236. <6>generic-usb 0003:413C:3200.0002: input: USB HID v1.10 Mouse [Dell Dell USB Mouse] on usb-sw-ehci-1.2/input0
  1237.  
  1238. [ 3.510000] generic-usb 0003:413C:3200.0002: input: USB HID v1.10 Mouse [Dell Dell USB Mouse] on usb-sw-ehci-1.2/input0
  1239. <6>usb 2-1.4: new high speed USB device number 5 using sw-ehci
  1240.  
  1241. [ 3.610000] usb 2-1.4: new high speed USB device number 5 using sw-ehci
  1242. <4>regulator_init_complete: axp20_buck3: incomplete constraints, leaving on
  1243.  
  1244. [ 4.050000] regulator_init_complete: axp20_buck3: incomplete constraints, leaving on
  1245. <4>regulator_init_complete: axp20_buck2: incomplete constraints, leaving on
  1246.  
  1247. [ 4.060000] regulator_init_complete: axp20_buck2: incomplete constraints, leaving on
  1248. <4>regulator_init_complete: axp20_ldo4: incomplete constraints, leaving on
  1249.  
  1250. [ 4.080000] regulator_init_complete: axp20_ldo4: incomplete constraints, leaving on
  1251. <4>regulator_init_complete: axp20_ldo3: incomplete constraints, leaving on
  1252.  
  1253. [ 4.090000] regulator_init_complete: axp20_ldo3: incomplete constraints, leaving on
  1254. <4>regulator_init_complete: axp20_ldo2: incomplete constraints, leaving on
  1255.  
  1256. [ 4.110000] regulator_init_complete: axp20_ldo2: incomplete constraints, leaving on
  1257. pcf8563_get_datetime,raw data is st1=08, st2=00, sec=13, min=22, hr=19, mday=16, wday=12, mon=02, year=03
  1258.  
  1259. [ 4.120000] pcf8563_get_datetime,raw data is st1=08, st2=00, sec=13, min=22, hr=19, mday=16, wday=12, mon=02, year=03
  1260. pcf8563_get_datetime: tm is secs=13, mins=22, hours=19,mday=16, mon=1, year=113, wday=2
  1261.  
  1262. [ 4.140000] pcf8563_get_datetime: tm is secs=13, mins=22, hours=19,mday=16, mon=1, year=113, wday=2
  1263. <6>pcf8563 1-0051: setting system clock to 2013-02-16 19:22:13 UTC (1361042533)
  1264.  
  1265. [ 4.160000] pcf8563 1-0051: setting system clock to 2013-02-16 19:22:13 UTC (1361042533)
  1266. <6>md: Waiting for all devices to be available before autodetect
  1267.  
  1268. [ 4.180000] md: Waiting for all devices to be available before autodetect
  1269. <6>md: If you don't use raid, use raid=noautodetect
  1270.  
  1271. [ 4.190000] md: If you don't use raid, use raid=noautodetect
  1272. <6>md: Autodetecting RAID arrays.
  1273.  
  1274. [ 4.200000] md: Autodetecting RAID arrays.
  1275. <6>md: Scanned 0 and added 0 devices.
  1276.  
  1277. [ 4.210000] md: Scanned 0 and added 0 devices.
  1278. <6>md: autorun ...
  1279.  
  1280. [ 4.210000] md: autorun ...
  1281. <6>md: ... autorun DONE.
  1282.  
  1283. [ 4.220000] md: ... autorun DONE.
  1284. <6>Waiting for root device /dev/mmcblk0p2...
  1285.  
  1286. [ 4.220000] Waiting for root device /dev/mmcblk0p2...
  1287. [mmc]: mmc 0 detect change, present 1
  1288.  
  1289. [ 4.240000] [mmc]: mmc 0 detect change, present 1
  1290. [mmc]: mmc 0 power on !!
  1291.  
  1292. [ 4.540000] [mmc]: mmc 0 power on !!
  1293. [mmc]: sdxc_request_done(L1113): [ 4.580000] [mmc]: sdxc_request_done(L1113): smc 0 err, cmd 52, RTO !!
  1294.  
  1295. smc 0 err, cmd 52, RTO !!
  1296. [mmc]: sdxc_request_done(L1113): [ 4.580000] [mmc]: sdxc_request_done(L1113): smc 0 err, cmd 52, RTO !!
  1297.  
  1298. smc 0 err, cmd 52, RTO !!
  1299. [mmc]: sdxc_request_done(L1113): [ 4.600000] [mmc]: sdxc_request_done(L1113): smc 0 err, cmd 5, RTO !!
  1300.  
  1301. smc 0 err, cmd 5, RTO !!
  1302. [mmc]: sdxc_request_done(L1113): [ 4.620000] [mmc]: sdxc_request_done(L1113): smc 0 err, cmd 5, RTO !!
  1303.  
  1304. smc 0 err, cmd 5, RTO !!
  1305. [mmc]: sdxc_request_done(L1113): [ 4.630000] [mmc]: sdxc_request_done(L1113): smc 0 err, cmd 5, RTO !!
  1306.  
  1307. smc 0 err, cmd 5, RTO !!
  1308. [mmc]: sdxc_request_done(L1113): [ 4.640000] [mmc]: sdxc_request_done(L1113): smc 0 err, cmd 5, RTO !!
  1309.  
  1310. smc 0 err, cmd 5, RTO !!
  1311. <6>mmc0: new high speed SDHC card at address b368
  1312.  
  1313. [ 4.690000] mmc0: new high speed SDHC card at address b368
  1314. <6>mmcblk0: mmc0:b368 SD 30.9 GiB
  1315.  
  1316. [ 4.700000] mmcblk0: mmc0:b368 SD 30.9 GiB
  1317. <6> mmcblk0: p1 p2
  1318.  
  1319. [ 4.710000] mmcblk0: p1 p2
  1320. <6>EXT3-fs: barriers not enabled
  1321.  
  1322. [ 4.780000] EXT3-fs: barriers not enabled
  1323. <6>kjournald starting. Commit interval 5 seconds
  1324.  
  1325. [ 4.790000] kjournald starting. Commit interval 5 seconds
  1326. <6>EXT3-fs (mmcblk0p2): using internal journal
  1327.  
  1328. [ 4.800000] EXT3-fs (mmcblk0p2): using internal journal
  1329. <6>EXT3-fs (mmcblk0p2): recovery complete
  1330.  
  1331. [ 4.810000] EXT3-fs (mmcblk0p2): recovery complete
  1332. <6>EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
  1333.  
  1334. [ 4.820000] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
  1335. <6>VFS: Mounted root (ext3 filesystem) on device 179:2.
  1336.  
  1337. [ 4.830000] VFS: Mounted root (ext3 filesystem) on device 179:2.
  1338. <6>devtmpfs: mounted
  1339.  
  1340. [ 4.840000] devtmpfs: mounted
  1341. <6>Freeing init memory: 164K
  1342.  
  1343. [ 4.840000] Freeing init memory: 164K
  1344.  
  1345. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S.
  1346. mount: wrong fs type, bad option, bad superblock on tmpfs,
  1347. missing codepage or helper program, or other error
  1348. (for several filesystems (e.g. nfs, cifs) you might
  1349. need a /sbin/mount.<type> helper program)
  1350. In some cases useful info is found in syslog - try
  1351. dmesg | tail or so
  1352.  
  1353. mount: wrong fs type, bad option, bad superblock on tmpfs,
  1354. missing codepage or helper program, or other error
  1355. (for several filesystems (e.g. nfs, cifs) you might
  1356. need a /sbin/mount.<type> helper program)
  1357. In some cases useful info is found in syslog - try
  1358. dmesg | tail or so
  1359.  
  1360. [....] Starting the hotplug events dispatcher: udevdudevd[148]: error: runtime directory '/run/udev' not writable, for now falling back to '/dev/.udev' <30>udevd[149]: starting version 175
  1361.  
  1362. [ 5.680000] udevd[149]: starting version 175
  1363. [?25l[?1c7[ ok 8[?25h[?0c.
  1364. [....] Synthesizing the initial hotplug events...[?25l[?1c7[ ok 8[?25h[?0cdone.
  1365. [....] Waiting for /dev to be fully populated...[?25l[?1c7[ ok 8[?25h[?0cdone.
  1366. mount: wrong fs type, bad option, bad superblock on tmpfs,
  1367. missing codepage or helper program, or other error
  1368. (for several filesystems (e.g. nfs, cifs) you might
  1369. need a /sbin/mount.<type> helper program)
  1370. In some cases useful info is found in syslog - try
  1371. dmesg | tail or so
  1372.  
  1373. [....] Activating swap...[?25l[?1c7[ ok 8[?25h[?0cdone.
  1374. [....] Cleaning up temporary files... /tmp[?25l[?1c7[ ok 8[?25h[?0c.
  1375. [....] Activating lvm and md swap...[?25l[?1c7[ ok 8[?25h[?0cdone.
  1376. [....] Checking file systems...fsck from util-linux 2.20.1
Advertisement
RAW Paste Data Copied
Advertisement