Flash Firmware VIA WM8650 serial by Morfes

WonderMedia Technologies, Inc.
W-Load Version : 0.16.00.01
UPDATE_ID_1_4_4_0_2_256MB_0160001
ethaddr............found
wloader finish


U-Boot 1.1.4 (Aug 24 2011 - 10:14:10)
WonderMedia Technologies, Inc.
U-Boot Version : UPDATEID_0.04.00.00.10
U-Boot code: 03F80000 -> 03FC3190  BSS: -> 03FCD724
boot from spi flash.
SF0: ManufID = C8, DeviceID = 4013 (Missing or Unknown FLASH)
     Use Default - Total size = 8MB, Sector size = 64KB
SF1: ManufID = FF, DeviceID = FFFF (Missing or Unknown FLASH)
     Use Default - Total size = 8MB, Sector size = 64KB
flash:
     Bank1: FF800000 -- FFFFFFFF
     Bank2: FF000000 -- FF7FFFFF
Flash: 16 MB
sfboot NAND:env nand config fail, use default flash id list info
pllb=0xc30, spec_clk=0x140a0cff
T1=2, clk1=16, div1=7, Thold=1, tREA=20+delay(9)
T2=1, clk2=30, div2=13, Thold2=1, comp=1
Tim1=393216 , Tim2=491520
T2 is greater and not use
T=2, clk=16, divisor=7, Thold=0x701
divisor is set 0x7, NFC_timing=0x2424
USE_HW_ECC ECC24bitPer1K
1 flash chips found. Total nand_chip size: 4096 MB
In:    serial
Out:   serial
Err:   serial
### main_loop entered: bootdelay=1

logocmd="nandrw r ${wmt.nfc.mtd.u-boot-logo} ${wmt.display.logoaddr} 10000; nandrw r ${wmt.nfc.mtd.u-boot-logo2} ${wmt.display.logoaddr2} 40000; nandrw r $"
block4095 tag=42627430  version =1
block4094 tag=31746242  version =1
bbt table is found
Load Image From NAND Flash page=0x11080
USE_HW_ECC ECC24bitPer1K

Read NAND Flash OK
Load Image From NAND Flash page=0x11100
USE_HW_ECC ECC24bitPer1K

Read NAND Flash OK
Load Image From NAND Flash page=0x11480
USE_HW_ECC ECC24bitPer1K

Read NAND Flash OK
[VOUT] ext dev : LCD
[VOUT] int dev : NO
[LCD] wmt default lcd (id 4,bpp 24)
vpp_config(800x480@60),pixclock 40000000
div_addr_offs=0x35c PLL_NO=1
[VPP] get base clock PLLC : 400000000
1div_addr_offs=0x374 PLL_NO=2
find the equal valuePLLN64, PLLD5, PLLP2, divisor2 freq=40000000Hz
PLL0x5440, pll addr =0xd8130208
PLLN64, PLLD5, PLLP2, div2 div_addr_offs=0x374
read divisor=2, pll=0x5440 from register
[GOVRH] set clock 40000000 ==> 40000000
div_addr_offs=0x374 PLL_NO=2
[VPP] get base clock PLLB : 40000000
vo_lcd_visible(1)
Hit any key to stop autoboot:  0

Initial SD/MMC Card OK!
SD/MMC clock is 25Mhz
register mmc device
part_offset : 800, cur_part : 1
part_offset : 800, cur_part : 1
reading wmt_scriptcmd

976 bytes read
## Executing script at 00000000
** Script length: 904
Erase all
Erase start at chip0 block 0 len=4092
Erase success 4088 failed 0
part_offset : 800, cur_part : 1
reading rootdev_tf

** Unable to read "rootdev_tf" from mmc 0:1 **

## Checking Image at 00400000 ...
   Bad Magic Number
Saving Environment to Flash...
Protect off FFFE0000 ... FFFEFFFF
Un-Protecting sectors 126..126 in bank 1
Un-Protected 1 sectors
Protect off FFFD0000 ... FFFDFFFF
Un-Protecting sectors 125..125 in bank 1
Un-Protected 1 sectors
Erasing Flash... FFFD0000 ... FFFDFFFF ...Erase Flash from 0xfffd0000 to 0xfffdffff in Bank # 1
Erasing sector 125 @ FFFD0000... ok.
Erased 1 sectors
Writing to Flash...  FFFD0005 ... FFFE0000 ...done
Protecting sectors 125..125 in bank 1
Protected 1 sectors
Protecting sectors 126..126 in bank 1
Protected 1 sectors
*E* lcd device 0 exist !
*E* lcd device 1 exist !
*E* lcd device 2 exist !
*E* lcd device 3 exist !
*E* lcd device 4 exist !
div_addr_offs=0x374 PLL_NO=2
[VPP] get base clock PLLB : 40000000
*W* vout mode register again 2
[VOUT] ext dev : LCD
[VOUT] int dev : NO
*W* vout mode register again 8
[LCD] wmt default lcd (id 4,bpp 24)
vpp_config(800x480@60),pixclock 40000000
div_addr_offs=0x35c PLL_NO=1
[VPP] get base clock PLLC : 400000000
1div_addr_offs=0x374 PLL_NO=2
find the equal valuePLLN64, PLLD5, PLLP2, divisor2 freq=40000000Hz
PLL0x5440, pll addr =0xd8130208
PLLN64, PLLD5, PLLP2, div2 div_addr_offs=0x374
read divisor=2, pll=0x5440 from register
[GOVRH] set clock 40000000 ==> 40000000
div_addr_offs=0x374 PLL_NO=2
[VPP] get base clock PLLB : 40000000
vo_lcd_visible(1)
x=30, y=30
argv[0] = textout, argv[1]=-1, argv[2]=-1, argv[3]="WM8650
"WM8650 Android2.2 upgrading ..."
part_offset : 800, cur_part : 1
reading FirmwareInstall/ramdisk.gz

2687312 bytes read
part_offset : 800, cur_part : 1
reading FirmwareInstall/uzImage.bin

3113388 bytes read
## Booting image at 00000000 ...
   Image Name:   Linux-2.6.32.9-default
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3113324 Bytes =  3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
No initrd
## Transferring control to Linux (at address 00008000) ...

Starting kernel ...

Uncompressing Linux.........................................................................................................................................
Linux version 2.6.32.9-default (jodyfu@szmce13) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #100 Wed Sep 21 08:25:24 HKT 2011
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: WMT
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 54356
Kernel command line: mem=214M root=dev/ram0 rw initrd=0x01000000,32768K console=ttyS0,115200n8 loadtime=-4
set load time = -4
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 214MB = 214MB total
Memory: 177408KB available (5496K code, 1132K data, 148K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 348.97 BogoMIPS (lpj=1744896)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
wmt_pci_init
PCI: WonderMidia Technology PCI Bridge
PCI: bus0: Fast back to back transfers disabled
[WMT-MB] Preparing VIDEO BUFFER (SIZE 32768 kB) ...
[WMT-MB] MAX MB Area size: Max 4096 Kbs Min 256 Kbs
[WMT-MB] prob /dev/Memory Block major 242, minor 0
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 32768K
ashmem: initialized
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
yaffs Sep 21 2011 08:24:47 Installing.
msgmni has been set to 410
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
un-know id = 0xc84013
un-know id = 0xffffff
wmt sf controller initial ok
Creating 6 MTD partitions on "mtdsf device":
0x000000000000-0x000000d00000 : "filesystem-SF"
0x000000d00000-0x000000f80000 : "kernel-SF"
0x000000f80000-0x000000fd0000 : "u-boot-SF"
0x000000fd0000-0x000000fe0000 : "u-boot env. cfg. 1-SF"
0x000000fe0000-0x000000ff0000 : "u-boot env. cfg. 2-SF"
0x000000ff0000-0x000001000000 : "w-load-SF"
1PMNAND_ADDR=0x7
kmalloc buffer env_ptr = 0xcd0e0000, env_ptr_nand = 0xcd0e0000
## Warning: "wmt.io.nand" not defined
## Warning: "wmt.dual.os" not defined
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd7947a (Samsung SAMSUNG_K9GBG08U0A)
PLLB=0x10, spec_clk=0x140a0cff
T1=2, clk1=17, div1=7, Thold=1, tREA=20+delay(9)
T2=1, clk2=30, div2=12, Thold2=1, comp=1
Tim1=417792 , Tim2=491520
T2 is greater and not use
T=2, clk=17, divisor=7, Thold=0x701
divisor PMNAND_ADDR is set 0x7, NFC_timing=0x2424
BCH ECC 24BIT
## Warning: "wmt.io.nand" not defined
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd7947a (Samsung SAMSUNG_K9GBG08U0A)
nand flash is not ready
Reset err, nand device is not ready
find bbt page is 524160
find bbt page is 524032
Bad block at 4
Bad block at 5
Bad block at 16
Bad block at 17
WMT_nand: uboot no dynamic partitions defined, use default static
Creating 11 MTD partitions on "WMT.nand":
0x000000000000-0x000000100000 : "w-load-NAND"
0x000000100000-0x000000a00000 : "u-boot env. cfg. 1-NAND"
0x000000a00000-0x000001300000 : "u-boot-NAND"
0x000001300000-0x000001b00000 : "kernel-NAND"
0x000001b00000-0x000002100000 : "initrd-NAND"
0x000002100000-0x000022100000 : "filesystem-NAND"
0x000022100000-0x000022900000 : "u-boot-logo"
0x000022900000-0x000022d00000 : "kernel-logo"
0x000022d00000-0x000086f00000 : "android-data"
0x000086f00000-0x00008ef00000 : "android-cache"
0x00008ef00000-0x000100000000 : "LocalDisk"
nand initialised ok
i2c /dev entries driver
I2C PORT0: Transfer Mode = 1; Speed Mode = 1
i2c: adding wmt_i2c_adapter0.
i2c: successfully added bus

I2C PORT1: Transfer Mode = 1; Speed Mode = 1; I2C1 PLL = 20M
i2c: adding wmt_i2c_adapter1.
i2c: successfully added bus
[wmt_i2c_api_i2c_init]
[wmt_i2c_api_init] wmt_i2c_api_init.
i2c: wmt algorithm module loaded.
## Warning: "wmt.display.direct_path" not defined
vpp_init(boot logo 1)
[VPP] GOVW TG 0,vpu en 0,vpu path 0
div_addr_offs=0x35c PLL_NO=1
[VPP] GOVW TG 0,vpu en 0,vpu path 0
[VPP] GOVW TG 1,vpu en 0,vpu path 0
[VPP] GOVW TG 1,vpu en 0,vpu path 0
[VO] vout_init: <1>vo_init_wm8435
vt1632 hw mode
[VOUT] ext dev : DVI
[VOUT] int dev : NO
## Warning: "wmt.display.user_res" not defined
## Warning: "wmt.display.regop" not defined
[VOUT] param 2:0:16:0:0:0
[VOUT] boot parm vo LCD opt 0,16, 0x0@0
## Warning: "wmt.display.param2" not defined
----------------------[VOUT] pwm 0:25:50:99 -------------------
[VOUT] blt 0,scalar 25,period 50,duty 99
[VOUT] tmr 40000:0:10:46:800:20:10:23:480:10
[VOUT] tmr pixclk 40000000,option 0x0,hsync 10,hbp 46,hpixel 800,hfp 20,vsync 10,vbp 23,vpixel 480,vfp 10
[VOUT] boot argument vo1 2,vo2 9
[VO] vo_boot_init: <7>vo_boot_init(0)
vo_init_wm8440 (BOOT 800x480,0)
gefb: framebuffer at 0f800000, mapped to d0000000, using 8192k, total 8192k
Console: switching to colour frame buffer device 100x30
fb0: wmtfb frame buffer device
loadtime = -4
[VO] vo_boot_config: <7>vo_boot_config
[VO] vo_boot_config: <7>Exit vo_boot_config
div_addr_offs=0x35c PLL_NO=1
[VPP] GOVW TG 0,vpu en 0,vpu path 0
[VPP] GOVW TG 1,vpu en 0,vpu path 0
[VPP] GOVW TG 1,vpu en 0,vpu path 0
fb1: WMT VPU frame buffer device
Enter pwm_init
mknod /dev/wmtgpio c 253 0
WMT vibrater driver load successfully!
uart.0: ttyS0 at MMIO 0xd8200000 (irq = 32) is a wmt serial
uart.1: ttyS1 at MMIO 0xd82b0000 (irq = 33) is a wmt serial
WMT Serial driver initialized: ok
brd: module loaded
loop: module loaded
nbd: registered device at major 43
pmem: 1 init
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
## Warning: "wmt.io.mac.off" not defined
VIA Rhine Family Fast Ethernet Adapter Driver Ver. 5.08
Copyright (c) 2002 VIA Technologies, Inc.
eth0: VIA Rhine III Fast Ethernet Adapter
eth0: MAC=00:40:63:23:99:44 IO=0xd8004000 Mem=0xd8004000  IRQ=10
usbcore: registered new interface driver asix
Linux video capture interface: v2.00
WonderMedia CMOS camera register OK
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
[wmt-vd] prob /dev/wmt-vd major 236, minor 0, prdt ffb1d000/8dc0000, size 100 KB
[wmt-vd] WonderMedia HW decoder driver inited
[wmt-lock] init ok, major=242, minor=1
## Warning: "wmt.gpo.cmos" not defined
Can't get cmos config in u-boot!!!!
Dean:spi_probe
spi irq num = 0x18
B:0
A:8
spi_probe: /dev/WMT_SPI major number 153, minor number 0, device number 1
WMT EVB SPI Controlor Driver OK!
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: enabling device 0000:00:04.0 (0040 -> 0042)
ehci_hcd 0000:00:04.0: EHCI Host Controller
ehci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.0: irq 43, io mem 0xd8007900
ehci_hcd 0000:00:04.0: USB 0.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32.9-default ehci_hcd
usb usb1: SerialNumber: 0000:00:04.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
PCI: enabling device 0000:00:05.0 (0000 -> 0001)
uhci_hcd 0000:00:05.0: UHCI Host Controller
uhci_hcd 0000:00:05.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:05.0: detected 2 ports
uhci_hcd 0000:00:05.0: irq 43, io base 0xd8007b00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32.9-default uhci_hcd
usb usb2: SerialNumber: 0000:00:05.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: enabling device 0000:00:06.0 (0000 -> 0001)
uhci_hcd 0000:00:06.0: UHCI Host Controller
uhci_hcd 0000:00:06.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:06.0: detected 2 ports
uhci_hcd 0000:00:06.0: irq 43, io base 0xd8008d00
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.32.9-default uhci_hcd
usb usb3: SerialNumber: 0000:00:06.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
debug:1 by rubbitxiao
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
usbcore: registered new interface driver VIAUSBModem
LinuxVIAUSBD1.0.4:VIA USB CDMA Modem
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
USB Serial support registered for GobiSerial
usbcore: registered new interface driver GobiSerial
GobiSerial: 1.0.20
udc: VIA UDC driver, version: 3 December 2007 (dma)
udc: pullup_disable()
mount_thread
udc: wmt_udc_probe - request_irq(0x2B) pass!
mice: PS/2 mouse device common for all mice
## Warning: "wmt.io.ts" not defined
===== UTK Touch Disabled!=====
wmt_rtc on
using rtc device, wmt-rtc, for alarms
wmt-rtc wmt-rtc.0: rtc core: registered wmt-rtc as rtc0
WMT Real Time Clock driver v0.54 initialized: ok
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
device-mapper: multipath: version 1.1.0 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
device-mapper: multipath queue-length: version 0.1.0 loaded
device-mapper: multipath service-time: version 0.2.0 loaded
WMT ATSMB (AHB To SD/MMC Bus) controller registered!
## Warning: "rootdev" not defined
Do not initialize mmc1 when boot from NandFlash.
[MMC/SD driver] ATSMB1 probe Failed!
sdmmc1: probe of sdmmc1.0 failed with error -22
## Warning: "wmt.io.bri_max" not defined
------------------ lcd_backlight_probe ---------------
Registered led device: lcd-backlight
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
logger: created 256K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
Advanced Linux Sound Architecture Driver Version 1.0.21.
No device for DAI VT1603
No device for DAI HWDEC
i2c_transfer returned -5
WM8900 0-001b: Device is not a WM8900 - ID 0
WMT_SOC: dai_name=i2s, codec_name=vt1603
No device for DAI wmt-i2s-dai
[VPP] set audio(fmt 16,rate 44100,ch 2)
VT1603 Audio Codec 0.10
wmt.audio.i2s = vt1603:f1:f2:ff:ff:100
[i2sbus] invalid. set i2c_bus->1
[mic/linein] invalid. set record->mic
playback volume percent[100%]
## Warning: "wmt.audio.echo.cancel" not defined
## Warning: "wmt.audio.channel.invert" not defined
asoc: VT1603 <-> wmt-i2s-dai mapping ok
ALSA device list:
  #0: WMT_SOC (VT1603)
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
## Warning: "wmt.io.pwkey" not defined
input: kpadPower as /devices/virtual/input/input0
[wmt_pm_init] battery_used = 3
PMC: WonderMedia Power Management driver
PMC: Power button is configured as soft power
[wmt_pm_init] power_on = 100 resume = 0 power_up = 500
registered taskstats version 1
===== VT1609 Touch Screen Driver Enabled!=====
## Warning: "wmt.vt1609.param" not defined
wmt.vt1609.param not set, use default parameter.
[VT160X] bus=spi0, p.x = 800, p.y = 480, gpio=2, irq=6
mount_thread
## Warning: "wmt.tsc.key" not defined
Read wmt.tsc.key Failed.
input: VT1609 TSC as /devices/virtual/input/input1
VT1609 Touch Screen Driver Installed!
>>>> vx_max=4095,vy_max=2078, vxy=17 ver=0.1 <<<<
VT1609 Dual Touch Support Enabled.
wmt-rtc wmt-rtc.0: setting system clock to 2012-01-19 23:22:10 UTC (1327015330)
VT160X Battery: SPI0, Sample Interval:10 sec
VT160X SAR-ADC Battery Driver Installed!
## Warning: "wmt.audio.echo.cancel" not defined
RAMDISK: gzip image found at block 0
mmc0: new high speed SD card at address 0002
mmcblk0: mmc0:0002 00000 971 MiB
 mmcblk0: p1
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: checktime reached, running e2fsck is recommended
EXT3 FS on ram0, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) on device 1:0.
0
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...NTFS-fs warning (device mmcblk0): parse_options(): Option utf8 is no longer supported, using option nls=utf8. Plea.
yaffs: dev is 187695104 name is "mmcblk0"
yaffs: passed flags "utf8=true"
yaffs: Bad mount option "utf8=true"
yaffs: dev is 187695104 name is "mmcblk0"
yaffs: passed flags "utf8=true"
yaffs: Bad mount option "utf8=true"
done.
0
Activating swap...done.
Starting mounting local filesystems: mount  failed (1: ).
Setting up networking ....
/etc/network/options is deprecated.
Setting up IP spoofing protection: rp_filter done.
Disabling TCP/IP SYN cookies: done.
Disabling IPv4 packet forwarding: done.
Disabling TCP/IP Explicit Congestion Notification: done.
Starting network interfaces:  rx_thresh : 18 ([S&F]=0x38, 64DW=0x18)
eth0: failed to detect cable link
done.
LOCATION=/mnt/mmcblk0p1/FirmwareInstall
set fs 20, 800x480
Using /mnt/mmcblk0p1/FirmwareInstall/autorun.sh
DEFAULT_SCENARIO=2
INSTALL_BASIC=0
INSTALL_RECOMMENDED=0
INSTALL_FULL=0
TIMEOUT_MENU=0
TIMEOUT_STARTUP=3
TIMEOUT_EXIT=3
MAC_0=AUTO
MAC_INCREMENT=0

INIT_LOCAL_DISK=1
ROOT_DEV=0
bsp_ver_check ... skip
fstype = ext3
Install Scenario NO.2
[WMT] prepare depending files...
[WMT] waitting for shell-UI ready...
INFO  [23:22:18] FrameBuffer phy addr 0xF800000, map len = 8388608, one screen len = 768000, offset(0,0)
INFO  [23:22:18] FBInfo (800 x 480) bpp(16), Bpp(2), Line(1600), Addr(0x40452000)
INFO  [23:22:18] FB Triple Buffer Disable OK
WonderMedia VGUI Version: 2.3.3 (built: Mar  9 2011 14:52:02)
INFO  [23:22:18] Error: <libvguihw.so: cannot open shared object file: No such file or directory>
   No HW accel avaliable.
Frame Buffer Map address : 0x40452000
DEBUG [23:22:18] Runtime : (1421) process <buildin>  connected
DEBUG [23:22:18] GUI application init ok.
[--I] receive startup type=7
UpdateWnd::create()
focus window class name 13WmsSmoothGrid
[WmsNotifier::onRead()] 2@WM8650 Android2.2 FW Upgrading ...
Executing do_install(2)
[DBG] ROOT_DEV=0, DEV_TF=1
[WmsNotifier::onRead()] 5@DON'T REMOVE INSTALLATION MEDIA...
[WmsNotifier::onRead()] 1@Upgrading W-Load to SF.
[WMT] wload_updateid: UPDATEID_DDR3_700M_1066M_16bit_2_256MB_0160001
[WMT] wild_wload_name: *_DDR3_700M_1066M_16bit_2_256MB_*
[WMT] *W* no w-load updated file
[WmsNotifier::onRead()] 3@5
[WmsNotifier::onRead()] 1@Upgrading U-Boot to SF.
[WMT] uboot_updateid_board: UPDATEID_0.04.00.00.10
[WMT] uboot_updateid_file: UPDATEID_0.04.00.00.10
[WMT] no newer u-boot file, skip.
[WmsNotifier::onRead()] 3@15
[WmsNotifier::onRead()] 1@Upgrading U-Boot env. cfg. to SF.
[WMT] add additionl uboot env...
random_mac: 00:40:63:18:06:31
restore: serialnum=9a9ab2cebea8e6aa60717b1749dd3808 to /tmp/setenv.tmp
[do_setenv] infile=/tmp/setenv.tmp
[do_setenv] outfile=/tmp/uboot_env.raw
[do_setenv] tmpfile=/tmp/uboot_env.tmp
0x3b 0xa1 0xe4 0x8e 65531 /tmp/uboot_env.raw
Erasing 64 Kibyte @ 10000 -- 100 % complete.
[do_setenv] infile=/tmp/setenv.tmp
[do_setenv] outfile=/tmp/uboot_env.raw
[do_setenv] tmpfile=/tmp/uboot_env.tmp
0x3b 0xa1 0xe4 0x8e 65531 /tmp/uboot_env.raw
Erasing 64 Kibyte @ 10000 -- 100 % complete.
[WmsNotifier::onRead()] 3@25
[WmsNotifier::onRead()] 1@Upgrading Ramdisk to NAND.
Update /mnt/mmcblk0p1/FirmwareInstall/initrd.gz to /dev/mtd10 ... flash eraseall /dev/mtd10 ...
flash eraseall done
done
[WmsNotifier::onRead()] 3@30
[WmsNotifier::onRead()] 1@Upgrading Kernel to NAND.
Update /mnt/mmcblk0p1/FirmwareInstall/uzImage.bin to /dev/mtd9 ... flash eraseall /dev/mtd9 ...
flash eraseall done
done
[WmsNotifier::onRead()] 3@35
[WmsNotifier::onRead()] 1@Upgrading FileSystem partition(Nand)...
yaffs: dev is 32505867 name is "mtdblock11"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.11, "mtdblock11"
yaffs_read_super: isCheckpointed 0

[WmsNotifier::onRead()] 3@40
[WmsNotifier::onRead()] 1@    Res_WmtLauncher.tgz
Install /mnt/mmcblk0p1/FirmwareInstall/packages/Res_WmtLauncher.tgz (1 / 7)
[WmsNotifier::onRead()] 3@45
[WmsNotifier::onRead()] 1@    Res_WmtPhoto.tgz
Install /mnt/mmcblk0p1/FirmwareInstall/packages/Res_WmtPhoto.tgz (2 / 7)
[WmsNotifier::onRead()] 3@50
[WmsNotifier::onRead()] 1@    Res_WmtWeather.tgz
Install /mnt/mmcblk0p1/FirmwareInstall/packages/Res_WmtWeather.tgz (3 / 7)
[WmsNotifier::onRead()] 3@55
[WmsNotifier::onRead()] 1@    WM8650_dsp_R1.01.12.tgz
Install /mnt/mmcblk0p1/FirmwareInstall/packages/WM8650_dsp_R1.01.12.tgz (4 / 7)
[WmsNotifier::onRead()] 3@60
[WmsNotifier::onRead()] 1@    WM8650_dsp_copybit_R1.0.4.tgz
Install /mnt/mmcblk0p1/FirmwareInstall/packages/WM8650_dsp_copybit_R1.0.4.tgz (5 / 7)
[WmsNotifier::onRead()] 3@65
[WmsNotifier::onRead()] 1@    android2.2-froyo.tgz
Install /mnt/mmcblk0p1/FirmwareInstall/packages/android2.2-froyo.tgz (6 / 7)
[WmsNotifier::onRead()] 3@70
[WmsNotifier::onRead()] 1@    busybox-1.16.0.mvl5_v5t.tgz
Install /mnt/mmcblk0p1/FirmwareInstall/packages/busybox-1.16.0.mvl5_v5t.tgz (7 / 7)
[WmsNotifier::onRead()] 1@    copy rootfs patch&restore files...
[WMT] copy all data patch to FileSystem for foctroy-recovery
save exit: isCheckpointed 1
[WmsNotifier::onRead()] 3@75

Execute bspinst_addons.sh

[WmsNotifier::onRead()] 1@Upgrading U-Boot LOGO to NAND
[WMT] update uboot-logo u-boot-logo-ver.data
[WMT] update uboot-logo2
done
[WmsNotifier::onRead()] 3@76
[WmsNotifier::onRead()] 1@Upgrading Kernel LOGO to NAND
[WMT] update kernel-logo
done
[WmsNotifier::onRead()] 3@78
[WmsNotifier::onRead()] 1@copy data to Android-Data partition(Nand)...
yaffs: dev is 32505870 name is "mtdblock14"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.14, "mtdblock14"
yaffs_read_super: isCheckpointed 0
[WMT] copy data package to data partition...
[WmsNotifier::onRead()] 3@85
[WmsNotifier::onRead()] 3@90
save exit: isCheckpointed 1
yaffs: dev is 32505872 name is "mtdblock16"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.16, "mtdblock16"
block 1806 is bad
block 1807 is bad
block 1808 is bad
block 1809 is bad
yaffs_read_super: isCheckpointed 0
[WMT] Creating UDC udc_file...\n
mkdosfs 2.11 (12 Mar 2005)
save exit: isCheckpointed 1
[WmsNotifier::onRead()] 1@copy pre-files to LocalDisk...
save exit: isCheckpointed 1
[WMT] copy pre-files to LocalDisk, done

Execute bspinst_addons.sh done.

[WmsNotifier::onRead()] 3@100
WonderMedia Android FW installation is complete.
save exit: isCheckpointed 1
save exit: isCheckpointed 1
save exit: isCheckpointed 1
save exit: isCheckpointed 1
[WmsNotifier::onRead()] 5@PLEASE REMOVE INSTALLATION MEDIA...