Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- ▒▒▒DDR Version 1.20 20190314
- In
- channel 0
- CS = 0
- MR0=0x98
- MR4=0x1
- MR5=0xFF
- MR8=0x8
- MR12=0x72
- MR14=0x72
- MR18=0x0
- MR19=0x0
- MR24=0x8
- MR25=0x0
- CS = 1
- MR0=0x18
- MR4=0x1
- MR5=0xFF
- MR8=0x8
- MR12=0x72
- MR14=0x72
- MR18=0x0
- MR19=0x0
- MR24=0x8
- MR25=0x0
- channel 1
- CS = 0
- MR0=0x98
- MR4=0x1
- MR5=0xFF
- MR8=0x8
- MR12=0x72
- MR14=0x72
- MR18=0x0
- MR19=0x0
- MR24=0x8
- MR25=0x0
- CS = 1
- MR0=0x18
- MR4=0x1
- MR5=0xFF
- MR8=0x8
- MR12=0x72
- MR14=0x72
- MR18=0x0
- MR19=0x0
- MR24=0x8
- MR25=0x0
- channel 0 training pass!
- channel 1 training pass!
- change freq to 400MHz 0,1
- channel 0
- CS = 0
- MR0=0x98
- MR4=0x1
- MR5=0xFF
- MR8=0x8
- MR12=0x72
- MR14=0x72
- MR18=0x0
- MR19=0x0
- MR24=0x8
- MR25=0x0
- CS = 1
- MR0=0x18
- MR4=0x1
- MR5=0xFF
- MR8=0x8
- MR12=0x72
- MR14=0x72
- MR18=0x0
- MR19=0x0
- MR24=0x8
- MR25=0x0
- channel 1
- CS = 0
- MR0=0x98
- MR4=0x1
- MR5=0xFF
- MR8=0x8
- MR12=0x72
- MR14=0x72
- MR18=0x0
- MR19=0x0
- MR24=0x8
- MR25=0x0
- CS = 1
- MR0=0x18
- MR4=0x1
- MR5=0xFF
- MR8=0x8
- MR12=0x72
- MR14=0x72
- MR18=0x0
- MR19=0x0
- MR24=0x8
- MR25=0x0
- channel 0 training pass!
- channel 1 training pass!
- change freq to 800MHz 1,0
- Channel 0: LPDDR4,800MHz
- Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
- Channel 1: LPDDR4,800MHz
- Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
- 256B stride
- ch 0 ddrconfig = 0x101, ddrsize = 0x2020
- ch 1 ddrconfig = 0x101, ddrsize = 0x2020
- pmugrf_os_reg[2] = 0x3AA1FAA1, stride = 0xD
- OUT
- Boot1: 2018-06-26, version: 1.14
- CPUId = 0x0
- ChipType = 0x10, 221
- Spi_ChipId = b4016
- SpiBootInit:0
- mmc0:cmd8,32
- mmc0:cmd5,32
- mmc0:cmd55,32
- mmc0:cmd1,32
- mmc0:cmd8,32
- mmc0:cmd5,32
- mmc0:cmd55,32
- mmc0:cmd1,32
- mmc0:cmd8,32
- mmc0:cmd5,32
- mmc0:cmd55,32
- mmc0:cmd1,32
- SdmmcInit=0 1
- StorageInit ok = 21738
- SecureMode = 0
- SecureInit ret = 0, SecureMode = 0
- GPT vendor signature is wrong
- LoadTrust Addr:0x1800
- No find bl30.bin
- No find bl32.bin
- Load uboot, ReadLba = 1000
- Load OK, addr=0x200000, size=0xee888
- RunBL31 0x10000
- NOTICE: BL31: v1.3(debug):0e7a845
- NOTICE: BL31: Built : 16:13:46, Apr 17 2019
- NOTICE: BL31: Rockchip release version: v1.1
- INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
- INFO: Using opteed sec cpu_context!
- INFO: boot cpu mask: 0
- INFO: plat_rockchip_pmu_init(1181): pd status 3e
- INFO: BL31: Initializing runtime services
- WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
- ERROR: Error initializing runtime service opteed_fast
- INFO: BL31: Preparing for EL3 exit to normal world
- INFO: Entry point address = 0x200000
- INFO: SPSR = 0x3c9
- U-Boot 2017.09-02676-g4490220395 (Jul 01 2019 - 07:49:56 +0000)
- Model: Rockchip RK3399 rockpi4b Board
- PreSerial: 2
- DRAM: 3.9 GiB
- Relocation Offset is: f5be0000
- Sysmem: init
- I2c speed: 400000Hz
- PMIC: RK808
- vdd-center init 950000 uV
- MMC: dwmmc@fe320000: 1, sdhci@fe330000: 0
- Using default environment
- Model: Rockchip RK3399 rockpi4b Board
- dcache off
- Device 0: GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
- Repair the backup gpt table OK!
- Vendor: 0x144d Rev: EXH7101Q Prod: S4GGNE0M704770
- Type: Hard Disk
- Capacity: 244198.3 MB = 238.4 GB (500118192 x 512)
- ... is now current device
- Bootdev: nvme 0
- rockchip_get_bootdev: can't find dev_desc!
- [Vendor ERROR]:Invalid boot device type(0)
- rockchip_get_bootdev: can't find dev_desc!
- [Vendor ERROR]:Invalid boot device type(0)
- rockchip_get_bootdev: can't find dev_desc!
- rockchip_get_boot_mode: dev_desc is NULL!
- rockchip_get_bootdev: can't find dev_desc!
- init_resource_list: dev_desc is NULL!
- Can't find file:logo.bmp
- failed to display uboot logo
- CLK: (uboot. arml: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
- CLK: (uboot. armb: enter 24000 KHz, init 24000 KHz, kernel 0N/A)
- aplll 816000 KHz
- apllb 24000 KHz
- dpll 800000 KHz
- cpll 24000 KHz
- gpll 800000 KHz
- npll 600000 KHz
- vpll 24000 KHz
- aclk_perihp 133333 KHz
- hclk_perihp 66666 KHz
- pclk_perihp 33333 KHz
- aclk_perilp0 266666 KHz
- hclk_perilp0 88888 KHz
- pclk_perilp0 44444 KHz
- hclk_perilp1 100000 KHz
- pclk_perilp1 50000 KHz
- Net: eth0: ethernet@fe300000
- Hit key to stop autoboot('CTRL+C'): 0
- Device 0: Vendor: 0x144d Rev: EXH7101Q Prod: S4GGNE0M704770
- Type: Hard Disk
- Capacity: 244198.3 MB = 238.4 GB (500118192 x 512)
- ... is now current device
- Scanning nvme 0:4...
- Found /extlinux/extlinux.conf
- pxefile_addr_str = 0x00500000
- bootfile = /extlinux/extlinux.conf
- Retrieving file: /extlinux/extlinux.conf
- reading /extlinux/extlinux.conf
- 598 bytes read in 1 ms (584 KiB/s)
- select kernel
- 1: kernel-4.4.154-90-rockchip-ga14f6502e045
- 2: kernel-4.4.154-88-rockchip-00030-g90239a6
- Enter choice: Retrieving file: /hw_intfc.conf
- reading /hw_intfc.conf
- 1720 bytes read in 1 ms (1.6 MiB/s)
- dtoverlay number: 0, name:/overlays/console-on-ttyS2.dtbo
- dtoverlay number: 1, name:/overlays/spi1-flash.dtbo
- hw_conf.valid = 1
- hw_conf.pwm0 = 0
- hw_conf.pwm1 = 0
- hw_conf.uart2 = 0
- hw_conf.uart4 = 0
- hw_conf.spi1 = 1
- hw_conf.spi2 = 0
- hw_conf.i2c2 = 0
- hw_conf.i2c6 = 0
- hw_conf.i2c7 = 0
- hw_conf.dts_overlay_count = 2
- hw_conf.dts_overlay[0] = /overlays/console-on-ttyS2.dtbo
- hw_conf.dts_overlay[1] = /overlays/spi1-flash.dtbo
- 1: kernel-4.4.154-90-rockchip-ga14f6502e045
- Retrieving file: /vmlinuz-4.4.154-90-rockchip-ga14f6502e045
- reading /vmlinuz-4.4.154-90-rockchip-ga14f6502e045
- ERROR: status = 2013, phase = 0, head = 1
- Error reading cluster
- ** Unable to read file /vmlinuz-4.4.154-90-rockchip-ga14f6502e045 **
- Skipping kernel-4.4.154-90-rockchip-ga14f6502e045 for failure retrieving kernel
- Retrieving file: /hw_intfc.conf
- reading /hw_intfc.conf
- 1720 bytes read in 1 ms (1.6 MiB/s)
- dtoverlay number: 2, name:/overlays/console-on-ttyS2.dtbo
- dtoverlay number: 3, name:/overlays/spi1-flash.dtbo
- hw_conf.valid = 1
- hw_conf.pwm0 = 0
- hw_conf.pwm1 = 0
- hw_conf.uart2 = 0
- hw_conf.uart4 = 0
- hw_conf.spi1 = 1
- hw_conf.spi2 = 0
- hw_conf.i2c2 = 0
- hw_conf.i2c6 = 0
- hw_conf.i2c7 = 0
- hw_conf.dts_overlay_count = 4
- hw_conf.dts_overlay[0] =
- hw_conf.dts_overlay[1] =
- hw_conf.dts_overlay[2] = /overlays/console-on-ttyS2.dtbo
- hw_conf.dts_overlay[3] = /overlays/spi1-flash.dtbo
- 2: kernel-4.4.154-88-rockchip-00030-g90239a6
- Retrieving file: /vmlinuz-4.4.154-88-rockchip-00030-g90239a6
- reading /vmlinuz-4.4.154-88-rockchip-00030-g90239a6
- ERROR: status = 2013, phase = 1, head = 0
- Error reading cluster
- ** Unable to read file /vmlinuz-4.4.154-88-rockchip-00030-g90239a6 **
- Skipping kernel-4.4.154-88-rockchip-00030-g90239a6 for failure retrieving kernel
- SCRIPT FAILED: continuing...
- Card did not respond to voltage select!
- mmc_init: -95, time 10
- Card did not respond to voltage select!
- mmc_init: -95, time 26
- starting USB...
- USB0: USB EHCI 1.00
- USB1: USB OHCI 1.0
- USB2: failed to get usb phy
- Port not available.
- USB3: failed to get usb phy
- Port not available.
- USB4: Can't get the usbphy register address
- probe failed, error -6
- USB5: Can't get the usbphy register address
- probe failed, error -6
- scanning bus 0 for devices... 1 USB Device(s) found
- scanning bus 1 for devices... 1 USB Device(s) found
- scanning usb for storage devices... 0 Storage Device(s) found
- Device 0: unknown device
- ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
- Could not initialize PHY ethernet@fe300000
- missing environment variable: pxeuuid
- Retrieving file: /extlinux/pxelinux.cfg/01-be-60-81-88-ac-49
- ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
- Could not initialize PHY ethernet@fe300000
- Retrieving file: /extlinux/pxelinux.cfg/00000000
- ethernet@fe300000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
- Could not initialize PHY ethernet@fe300000
- Retrieving file: /extlinux/pxelinux.cfg/0000000
- ethernet@fe300000 Waiting for PHY auto negotiation to complete....user interrupt!
- Could not initialize PHY ethernet@fe300000
- Retrieving file: /extlinux/pxelinux.cfg/000000
- ethernet@fe300000 Waiting for PHY auto negotiation to complete.....user interrupt!
- Could not initialize PHY ethernet@fe300000
- Retrieving file: /extlinux/pxelinux.cfg/00000
- ethernet@fe300000 Waiting for PHY auto negotiation to complete.....
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement