Advertisement
Guest User

Untitled

a guest
Jun 21st, 2021
9
0
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 10.63 KB | None | 0 0
  1. === START OF INFORMATION SECTION ===
  2. Device Model: TOSHIBA MQ04ABF100
  3. Serial Number: 499EPHHYT
  4. LU WWN Device Id: 5 000039 93280435d
  5. Firmware Version: JU0A0E
  6. User Capacity: 1 000 204 886 016 bytes [1,00 TB]
  7. Sector Sizes: 512 bytes logical, 4096 bytes physical
  8. Rotation Rate: 5400 rpm
  9. Form Factor: 2.5 inches
  10. Zoned Device: Device managed zones
  11. Device is: Not in smartctl database [for details use: -P showall]
  12. ATA Version is: ACS-3 T13/2161-D revision 5
  13. SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
  14. Local Time is: Mon Jun 21 17:11:13 2021 EEST
  15. SMART support is: Available - device has SMART capability.
  16. SMART support is: Enabled
  17.  
  18. === START OF READ SMART DATA SECTION ===
  19. SMART overall-health self-assessment test result: PASSED
  20.  
  21. General SMART Values:
  22. Offline data collection status: (0x80) Offline data collection activity
  23. was never started.
  24. Auto Offline Data Collection: Enabled.
  25. Self-test execution status: ( 0) The previous self-test routine completed
  26. without error or no self-test has ever
  27. been run.
  28. Total time to complete Offline
  29. data collection: ( 120) seconds.
  30. Offline data collection
  31. capabilities: (0x5b) SMART execute Offline immediate.
  32. Auto Offline data collection on/off support.
  33. Suspend Offline collection upon new
  34. command.
  35. Offline surface scan supported.
  36. Self-test supported.
  37. No Conveyance Self-test supported.
  38. Selective Self-test supported.
  39. SMART capabilities: (0x0003) Saves SMART data before entering
  40. power-saving mode.
  41. Supports SMART auto save timer.
  42. Error logging capability: (0x01) Error logging supported.
  43. General Purpose Logging supported.
  44. Short self-test routine
  45. recommended polling time: ( 2) minutes.
  46. Extended self-test routine
  47. recommended polling time: ( 176) minutes.
  48. SCT capabilities: (0x003d) SCT Status supported.
  49. SCT Error Recovery Control supported.
  50. SCT Feature Control supported.
  51. SCT Data Table supported.
  52.  
  53. SMART Attributes Data Structure revision number: 16
  54. Vendor Specific SMART Attributes with Thresholds:
  55. ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
  56. 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
  57. 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
  58. 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1315
  59. 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 6502
  60. 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 55
  61. 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
  62. 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
  63. 9 Power_On_Hours 0x0032 083 083 000 Old_age Always - 6850
  64. 10 Spin_Retry_Count 0x0033 230 100 030 Pre-fail Always - 0
  65. 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1694
  66. 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 2887
  67. 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 93
  68. 193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 27946
  69. 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 39 (Min/Max 14/49)
  70. 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 55
  71. 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
  72. 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
  73. 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
  74. 206 Flying_Height 0x0020 100 100 000 Old_age Offline - 4294984389
  75. 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
  76. 222 Loaded_Hours 0x0032 084 084 000 Old_age Always - 6760
  77. 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
  78. 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
  79. 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 267
  80. 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
  81.  
  82. SMART Error Log Version: 1
  83. ATA Error Count: 16 (device log contains only the most recent five errors)
  84. CR = Command Register [HEX]
  85. FR = Features Register [HEX]
  86. SC = Sector Count Register [HEX]
  87. SN = Sector Number Register [HEX]
  88. CL = Cylinder Low Register [HEX]
  89. CH = Cylinder High Register [HEX]
  90. DH = Device/Head Register [HEX]
  91. DC = Device Command Register [HEX]
  92. ER = Error register [HEX]
  93. ST = Status register [HEX]
  94. Powered_Up_Time is measured from power on, and printed as
  95. DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
  96. SS=sec, and sss=millisec. It "wraps" after 49.710 days.
  97.  
  98. Error 16 occurred at disk power-on lifetime: 6849 hours (285 days + 9 hours)
  99. When the command that caused the error occurred, the device was active or idle.
  100.  
  101. After command completion occurred, registers were:
  102. ER ST SC SN CL CH DH
  103. -- -- -- -- -- -- --
  104. 40 41 78 a8 01 b2 40 Error: WP at LBA = 0x00b201a8 = 11665832
  105.  
  106. Commands leading to the command that caused the error were:
  107. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  108. -- -- -- -- -- -- -- -- ---------------- --------------------
  109. 61 08 a0 00 70 d0 40 00 01:38:11.761 WRITE FPDMA QUEUED
  110. 60 08 78 a8 01 b2 40 00 01:38:11.761 READ FPDMA QUEUED
  111. ef 10 02 00 00 00 a0 00 01:38:11.760 SET FEATURES [Enable SATA feature]
  112. 27 00 00 00 00 00 e0 00 01:38:11.760 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  113. ec 00 00 00 00 00 a0 00 01:38:11.759 IDENTIFY DEVICE
  114.  
  115. Error 15 occurred at disk power-on lifetime: 6849 hours (285 days + 9 hours)
  116. When the command that caused the error occurred, the device was active or idle.
  117.  
  118. After command completion occurred, registers were:
  119. ER ST SC SN CL CH DH
  120. -- -- -- -- -- -- --
  121. 40 41 78 a8 01 b2 40 Error: UNC at LBA = 0x00b201a8 = 11665832
  122.  
  123. Commands leading to the command that caused the error were:
  124. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  125. -- -- -- -- -- -- -- -- ---------------- --------------------
  126. 60 00 90 90 ef b2 40 00 01:38:11.382 READ FPDMA QUEUED
  127. 60 00 88 90 ee b2 40 00 01:38:11.368 READ FPDMA QUEUED
  128. 60 08 78 a8 01 b2 40 00 01:38:11.358 READ FPDMA QUEUED
  129. 60 00 30 90 ed b2 40 00 01:38:11.347 READ FPDMA QUEUED
  130. 60 00 28 90 ec b2 40 00 01:38:11.328 READ FPDMA QUEUED
  131.  
  132. Error 14 occurred at disk power-on lifetime: 6849 hours (285 days + 9 hours)
  133. When the command that caused the error occurred, the device was active or idle.
  134.  
  135. After command completion occurred, registers were:
  136. ER ST SC SN CL CH DH
  137. -- -- -- -- -- -- --
  138. 40 41 28 a8 01 b2 40 Error: UNC at LBA = 0x00b201a8 = 11665832
  139.  
  140. Commands leading to the command that caused the error were:
  141. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  142. -- -- -- -- -- -- -- -- ---------------- --------------------
  143. 60 08 38 00 ec bd 40 00 01:35:06.659 READ FPDMA QUEUED
  144. 60 08 28 a8 01 b2 40 00 01:35:06.659 READ FPDMA QUEUED
  145. 60 08 20 e0 83 b2 40 00 01:35:06.659 READ FPDMA QUEUED
  146. 60 00 18 80 59 52 40 00 01:35:06.659 READ FPDMA QUEUED
  147. ef 10 02 00 00 00 a0 00 01:35:06.658 SET FEATURES [Enable SATA feature]
  148.  
  149. Error 13 occurred at disk power-on lifetime: 6849 hours (285 days + 9 hours)
  150. When the command that caused the error occurred, the device was active or idle.
  151.  
  152. After command completion occurred, registers were:
  153. ER ST SC SN CL CH DH
  154. -- -- -- -- -- -- --
  155. 40 41 60 a8 01 b2 40 Error: UNC at LBA = 0x00b201a8 = 11665832
  156.  
  157. Commands leading to the command that caused the error were:
  158. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  159. -- -- -- -- -- -- -- -- ---------------- --------------------
  160. 60 08 60 a8 01 b2 40 00 01:35:06.243 READ FPDMA QUEUED
  161. 61 10 58 c0 0e be 40 00 01:35:06.190 WRITE FPDMA QUEUED
  162. ea 00 00 00 00 00 a0 00 01:35:06.070 FLUSH CACHE EXT
  163. 61 08 48 18 90 b4 40 00 01:35:06.069 WRITE FPDMA QUEUED
  164. ea 00 00 00 00 00 a0 00 01:35:06.024 FLUSH CACHE EXT
  165.  
  166. Error 12 occurred at disk power-on lifetime: 6849 hours (285 days + 9 hours)
  167. When the command that caused the error occurred, the device was active or idle.
  168.  
  169. After command completion occurred, registers were:
  170. ER ST SC SN CL CH DH
  171. -- -- -- -- -- -- --
  172. 40 41 b8 a8 01 b2 40 Error: UNC at LBA = 0x00b201a8 = 11665832
  173.  
  174. Commands leading to the command that caused the error were:
  175. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  176. -- -- -- -- -- -- -- -- ---------------- --------------------
  177. 60 08 b8 a8 01 b2 40 00 01:31:15.300 READ FPDMA QUEUED
  178. ef 10 02 00 00 00 a0 00 01:31:15.299 SET FEATURES [Enable SATA feature]
  179. 27 00 00 00 00 00 e0 00 01:31:15.299 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  180. ec 00 00 00 00 00 a0 00 01:31:15.299 IDENTIFY DEVICE
  181. ef 03 45 00 00 00 a0 00 01:31:15.298 SET FEATURES [Set transfer mode]
  182.  
  183. SMART Self-test log structure revision number 1
  184. No self-tests have been logged. [To run self-tests, use: smartctl -t]
  185.  
  186. SMART Selective self-test log data structure revision number 1
  187. SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
  188. 1 0 0 Not_testing
  189. 2 0 0 Not_testing
  190. 3 0 0 Not_testing
  191. 4 0 0 Not_testing
  192. 5 0 0 Not_testing
  193. Selective self-test flags (0x0):
  194. After scanning selected spans, do NOT read-scan remainder of disk.
  195. If Selective self-test is pending on power-up, resume after 0 minute delay.
  196.  
  197.  
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement