API tools faq
paste
selmaks

Untitled

selmaks
Feb 26th, 2023
15
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 173.89 KB | None | 0 0
raw download clone embed print report
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <https://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23.  
  24. /**
  25. * Configuration_adv.h
  26. *
  27. * Advanced settings.
  28. * Only change these if you know exactly what you're doing.
  29. * Some of these settings can damage your printer if improperly set!
  30. *
  31. * Basic settings can be found in Configuration.h
  32. */
  33. #define CONFIGURATION_ADV_H_VERSION 02000901
  34.  
  35. //===========================================================================
  36. //============================= Thermal Settings ============================
  37. //===========================================================================
  38. // @section temperature
  39.  
  40. /**
  41. * Thermocouple sensors are quite sensitive to noise. Any noise induced in
  42. * the sensor wires, such as by stepper motor wires run in parallel to them,
  43. * may result in the thermocouple sensor reporting spurious errors. This
  44. * value is the number of errors which can occur in a row before the error
  45. * is reported. This allows us to ignore intermittent error conditions while
  46. * still detecting an actual failure, which should result in a continuous
  47. * stream of errors from the sensor.
  48. *
  49. * Set this value to 0 to fail on the first error to occur.
  50. */
  51. #define THERMOCOUPLE_MAX_ERRORS 15
  52.  
  53. //
  54. // Custom Thermistor 1000 parameters
  55. //
  56. #if TEMP_SENSOR_0 == 1000
  57. #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  58. #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  59. #define HOTEND0_BETA 3950 // Beta value
  60. #endif
  61.  
  62. #if TEMP_SENSOR_1 == 1000
  63. #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  64. #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  65. #define HOTEND1_BETA 3950 // Beta value
  66. #endif
  67.  
  68. #if TEMP_SENSOR_2 == 1000
  69. #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  70. #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  71. #define HOTEND2_BETA 3950 // Beta value
  72. #endif
  73.  
  74. #if TEMP_SENSOR_3 == 1000
  75. #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  76. #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  77. #define HOTEND3_BETA 3950 // Beta value
  78. #endif
  79.  
  80. #if TEMP_SENSOR_4 == 1000
  81. #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  82. #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  83. #define HOTEND4_BETA 3950 // Beta value
  84. #endif
  85.  
  86. #if TEMP_SENSOR_5 == 1000
  87. #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  88. #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  89. #define HOTEND5_BETA 3950 // Beta value
  90. #endif
  91.  
  92. #if TEMP_SENSOR_6 == 1000
  93. #define HOTEND6_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  94. #define HOTEND6_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  95. #define HOTEND6_BETA 3950 // Beta value
  96. #endif
  97.  
  98. #if TEMP_SENSOR_7 == 1000
  99. #define HOTEND7_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  100. #define HOTEND7_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  101. #define HOTEND7_BETA 3950 // Beta value
  102. #endif
  103.  
  104. #if TEMP_SENSOR_BED == 1000
  105. #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  106. #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  107. #define BED_BETA 3950 // Beta value
  108. #endif
  109.  
  110. #if TEMP_SENSOR_CHAMBER == 1000
  111. #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  112. #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  113. #define CHAMBER_BETA 3950 // Beta value
  114. #endif
  115.  
  116. #if TEMP_SENSOR_COOLER == 1000
  117. #define COOLER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  118. #define COOLER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  119. #define COOLER_BETA 3950 // Beta value
  120. #endif
  121.  
  122. #if TEMP_SENSOR_PROBE == 1000
  123. #define PROBE_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  124. #define PROBE_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  125. #define PROBE_BETA 3950 // Beta value
  126.  
  127.  
  128.  
  129.  
  130.  
  131.  
  132. #endif
  133.  
  134. #if TEMP_SENSOR_REDUNDANT == 1000
  135. #define REDUNDANT_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  136. #define REDUNDANT_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  137. #define REDUNDANT_BETA 3950 // Beta value
  138. #endif
  139.  
  140.  
  141.  
  142.  
  143.  
  144.  
  145.  
  146.  
  147.  
  148.  
  149.  
  150. //
  151.  
  152.  
  153.  
  154.  
  155.  
  156.  
  157.  
  158. // Hephestos 2 24V heated bed upgrade kit.
  159. // https://store.bq.com/en/heated-bed-kit-hephestos2
  160. //
  161. //#define HEPHESTOS2_HEATED_BED_KIT
  162. #if ENABLED(HEPHESTOS2_HEATED_BED_KIT)
  163. #undef TEMP_SENSOR_BED
  164. #define TEMP_SENSOR_BED 70
  165. #define HEATER_BED_INVERTING true
  166. #endif
  167.  
  168. //
  169. // Heated Bed Bang-Bang options
  170. //
  171. #if DISABLED(PIDTEMPBED)
  172. #define BED_CHECK_INTERVAL 5000 // (ms) Interval between checks in bang-bang control
  173. #if ENABLED(BED_LIMIT_SWITCHING)
  174. #define BED_HYSTERESIS 2 // (°C) Only set the relevant heater state when ABS(T-target) > BED_HYSTERESIS
  175. #endif
  176. #endif
  177.  
  178. //
  179. // Heated Chamber options
  180. //
  181. #if DISABLED(PIDTEMPCHAMBER)
  182. #define CHAMBER_CHECK_INTERVAL 5000 // (ms) Interval between checks in bang-bang control
  183. #if ENABLED(CHAMBER_LIMIT_SWITCHING)
  184. #define CHAMBER_HYSTERESIS 2 // (°C) Only set the relevant heater state when ABS(T-target) > CHAMBER_HYSTERESIS
  185. #endif
  186. #endif
  187.  
  188. #if TEMP_SENSOR_CHAMBER
  189. //#define HEATER_CHAMBER_PIN P2_04 // Required heater on/off pin (example: SKR 1.4 Turbo HE1 plug)
  190. //#define HEATER_CHAMBER_INVERTING false
  191. //#define FAN1_PIN -1 // Remove the fan signal on pin P2_04 (example: SKR 1.4 Turbo HE1 plug)
  192.  
  193. //#define CHAMBER_FAN // Enable a fan on the chamber
  194. #if ENABLED(CHAMBER_FAN)
  195.  
  196. #define CHAMBER_FAN_MODE 2 // Fan control mode: 0=Static; 1=Linear increase when temp is higher than target; 2=V-shaped curve; 3=similar to 1 but fan is always on.
  197. #if CHAMBER_FAN_MODE == 0
  198. #define CHAMBER_FAN_BASE 255 // Chamber fan PWM (0-255)
  199. #elif CHAMBER_FAN_MODE == 1
  200. #define CHAMBER_FAN_BASE 128 // Base chamber fan PWM (0-255); turns on when chamber temperature is above the target
  201. #define CHAMBER_FAN_FACTOR 25 // PWM increase per °C above target
  202. #elif CHAMBER_FAN_MODE == 2
  203. #define CHAMBER_FAN_BASE 128 // Minimum chamber fan PWM (0-255)
  204. #define CHAMBER_FAN_FACTOR 25 // PWM increase per °C difference from target
  205. #elif CHAMBER_FAN_MODE == 3
  206. #define CHAMBER_FAN_BASE 128 // Base chamber fan PWM (0-255)
  207. #define CHAMBER_FAN_FACTOR 25 // PWM increase per °C above target
  208. #endif
  209. #endif
  210.  
  211. //#define CHAMBER_VENT // Enable a servo-controlled vent on the chamber
  212. #if ENABLED(CHAMBER_VENT)
  213. #define CHAMBER_VENT_SERVO_NR 1 // Index of the vent servo
  214. #define HIGH_EXCESS_HEAT_LIMIT 5 // How much above target temp to consider there is excess heat in the chamber
  215. #define LOW_EXCESS_HEAT_LIMIT 3
  216. #define MIN_COOLING_SLOPE_TIME_CHAMBER_VENT 20
  217. #define MIN_COOLING_SLOPE_DEG_CHAMBER_VENT 1.5
  218. #endif
  219. #endif
  220.  
  221. //
  222. // Laser Cooler options
  223. //
  224. #if TEMP_SENSOR_COOLER
  225. #define COOLER_MINTEMP 8 // (°C)
  226. #define COOLER_MAXTEMP 26 // (°C)
  227. #define COOLER_DEFAULT_TEMP 16 // (°C)
  228. #define TEMP_COOLER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
  229. #define COOLER_PIN 8 // Laser cooler on/off pin used to control power to the cooling element (e.g., TEC, External chiller via relay)
  230. #define COOLER_INVERTING false
  231. #define TEMP_COOLER_PIN 15 // Laser/Cooler temperature sensor pin. ADC is required.
  232. #define COOLER_FAN // Enable a fan on the cooler, Fan# 0,1,2,3 etc.
  233. #define COOLER_FAN_INDEX 0 // FAN number 0, 1, 2 etc. e.g.
  234. #if ENABLED(COOLER_FAN)
  235. #define COOLER_FAN_BASE 100 // Base Cooler fan PWM (0-255); turns on when Cooler temperature is above the target
  236. #define COOLER_FAN_FACTOR 25 // PWM increase per °C above target
  237. #endif
  238. #endif
  239.  
  240. //
  241. // Laser Coolant Flow Meter
  242. //
  243. //#define LASER_COOLANT_FLOW_METER
  244. #if ENABLED(LASER_COOLANT_FLOW_METER)
  245. #define FLOWMETER_PIN 20 // Requires an external interrupt-enabled pin (e.g., RAMPS 2,3,18,19,20,21)
  246. #define FLOWMETER_PPL 5880 // (pulses/liter) Flow meter pulses-per-liter on the input pin
  247. #define FLOWMETER_INTERVAL 1000 // (ms) Flow rate calculation interval in milliseconds
  248. #define FLOWMETER_SAFETY // Prevent running the laser without the minimum flow rate set below
  249. #if ENABLED(FLOWMETER_SAFETY)
  250. #define FLOWMETER_MIN_LITERS_PER_MINUTE 1.5 // (liters/min) Minimum flow required when enabled
  251. #endif
  252. #endif
  253.  
  254. /**
  255. * Thermal Protection provides additional protection to your printer from damage
  256. * and fire. Marlin always includes safe min and max temperature ranges which
  257. * protect against a broken or disconnected thermistor wire.
  258. *
  259. * The issue: If a thermistor falls out, it will report the much lower
  260. * temperature of the air in the room, and the the firmware will keep
  261. * the heater on.
  262. *
  263. * The solution: Once the temperature reaches the target, start observing.
  264. * If the temperature stays too far below the target (hysteresis) for too
  265. * long (period), the firmware will halt the machine as a safety precaution.
  266. *
  267. * If you get false positives for "Thermal Runaway", increase
  268. * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  269. */
  270. #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  271. #define THERMAL_PROTECTION_PERIOD 40 // Seconds
  272. #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
  273.  
  274. //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops
  275. #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
  276. //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303
  277. #endif
  278.  
  279. /**
  280. * Whenever an M104, M109, or M303 increases the target temperature, the
  281. * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature
  282. * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and
  283. * requires a hard reset. This test restarts with any M104/M109/M303, but only
  284. * if the current temperature is far enough below the target for a reliable
  285. * test.
  286. *
  287. * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD
  288. * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
  289. * below 2.
  290. */
  291. #define WATCH_TEMP_PERIOD 40 // Seconds
  292. #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
  293. #endif
  294.  
  295. /**
  296. * Thermal Protection parameters for the bed are just as above for hotends.
  297. */
  298. #if ENABLED(THERMAL_PROTECTION_BED)
  299. #define THERMAL_PROTECTION_BED_PERIOD 180 // Seconds
  300. #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
  301.  
  302. /**
  303. * As described above, except for the bed (M140/M190/M303).
  304. */
  305. #define WATCH_BED_TEMP_PERIOD 180 // Seconds
  306. #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
  307. #endif
  308.  
  309. /**
  310. * Thermal Protection parameters for the heated chamber.
  311. */
  312. #if ENABLED(THERMAL_PROTECTION_CHAMBER)
  313. #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
  314. #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
  315.  
  316. /**
  317. * Heated chamber watch settings (M141/M191).
  318. */
  319. #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
  320. #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
  321. #endif
  322.  
  323. /**
  324. * Thermal Protection parameters for the laser cooler.
  325. */
  326. #if ENABLED(THERMAL_PROTECTION_COOLER)
  327. #define THERMAL_PROTECTION_COOLER_PERIOD 10 // Seconds
  328. #define THERMAL_PROTECTION_COOLER_HYSTERESIS 3 // Degrees Celsius
  329.  
  330. /**
  331. * Laser cooling watch settings (M143/M193).
  332. */
  333. #define WATCH_COOLER_TEMP_PERIOD 60 // Seconds
  334. #define WATCH_COOLER_TEMP_INCREASE 3 // Degrees Celsius
  335. #endif
  336.  
  337.  
  338.  
  339.  
  340.  
  341.  
  342.  
  343.  
  344.  
  345. #if ENABLED(PIDTEMP)
  346. // Add an experimental additional term to the heater power, proportional to the extrusion speed.
  347. // A well-chosen Kc value should add just enough power to melt the increased material volume.
  348. //#define PID_EXTRUSION_SCALING
  349. #if ENABLED(PID_EXTRUSION_SCALING)
  350. #define DEFAULT_Kc (100) // heating power = Kc * e_speed
  351. #define LPQ_MAX_LEN 50
  352. #endif
  353.  
  354. /**
  355. * Add an experimental additional term to the heater power, proportional to the fan speed.
  356. * A well-chosen Kf value should add just enough power to compensate for power-loss from the cooling fan.
  357. * You can either just add a constant compensation with the DEFAULT_Kf value
  358. * or follow the instruction below to get speed-dependent compensation.
  359. *
  360. * Constant compensation (use only with fanspeeds of 0% and 100%)
  361. * ---------------------------------------------------------------------
  362. * A good starting point for the Kf-value comes from the calculation:
  363. * kf = (power_fan * eff_fan) / power_heater * 255
  364. * where eff_fan is between 0.0 and 1.0, based on fan-efficiency and airflow to the nozzle / heater.
  365. *
  366. * Example:
  367. * Heater: 40W, Fan: 0.1A * 24V = 2.4W, eff_fan = 0.8
  368. * Kf = (2.4W * 0.8) / 40W * 255 = 12.24
  369. *
  370. * Fan-speed dependent compensation
  371. * --------------------------------
  372. * 1. To find a good Kf value, set the hotend temperature, wait for it to settle, and enable the fan (100%).
  373. * Make sure PID_FAN_SCALING_LIN_FACTOR is 0 and PID_FAN_SCALING_ALTERNATIVE_DEFINITION is not enabled.
  374. * If you see the temperature drop repeat the test, increasing the Kf value slowly, until the temperature
  375. * drop goes away. If the temperature overshoots after enabling the fan, the Kf value is too big.
  376. * 2. Note the Kf-value for fan-speed at 100%
  377. * 3. Determine a good value for PID_FAN_SCALING_MIN_SPEED, which is around the speed, where the fan starts moving.
  378. * 4. Repeat step 1. and 2. for this fan speed.
  379. * 5. Enable PID_FAN_SCALING_ALTERNATIVE_DEFINITION and enter the two identified Kf-values in
  380. * PID_FAN_SCALING_AT_FULL_SPEED and PID_FAN_SCALING_AT_MIN_SPEED. Enter the minimum speed in PID_FAN_SCALING_MIN_SPEED
  381. */
  382. //#define PID_FAN_SCALING
  383. #if ENABLED(PID_FAN_SCALING)
  384. //#define PID_FAN_SCALING_ALTERNATIVE_DEFINITION
  385. #if ENABLED(PID_FAN_SCALING_ALTERNATIVE_DEFINITION)
  386. // The alternative definition is used for an easier configuration.
  387. // Just figure out Kf at fullspeed (255) and PID_FAN_SCALING_MIN_SPEED.
  388. // DEFAULT_Kf and PID_FAN_SCALING_LIN_FACTOR are calculated accordingly.
  389.  
  390. #define PID_FAN_SCALING_AT_FULL_SPEED 13.0 //=PID_FAN_SCALING_LIN_FACTOR*255+DEFAULT_Kf
  391. #define PID_FAN_SCALING_AT_MIN_SPEED 6.0 //=PID_FAN_SCALING_LIN_FACTOR*PID_FAN_SCALING_MIN_SPEED+DEFAULT_Kf
  392. #define PID_FAN_SCALING_MIN_SPEED 10.0 // Minimum fan speed at which to enable PID_FAN_SCALING
  393.  
  394. #define DEFAULT_Kf (255.0*PID_FAN_SCALING_AT_MIN_SPEED-PID_FAN_SCALING_AT_FULL_SPEED*PID_FAN_SCALING_MIN_SPEED)/(255.0-PID_FAN_SCALING_MIN_SPEED)
  395. #define PID_FAN_SCALING_LIN_FACTOR (PID_FAN_SCALING_AT_FULL_SPEED-DEFAULT_Kf)/255.0
  396.  
  397. #else
  398. #define PID_FAN_SCALING_LIN_FACTOR (0) // Power loss due to cooling = Kf * (fan_speed)
  399. #define DEFAULT_Kf 10 // A constant value added to the PID-tuner
  400. #define PID_FAN_SCALING_MIN_SPEED 10 // Minimum fan speed at which to enable PID_FAN_SCALING
  401. #endif
  402. #endif
  403. #endif
  404.  
  405. /**
  406. * Automatic Temperature Mode
  407. *
  408. * Dynamically adjust the hotend target temperature based on planned E moves.
  409. *
  410. * (Contrast with PID_EXTRUSION_SCALING, which tracks E movement and adjusts PID
  411. * behavior using an additional kC value.)
  412. *
  413. * Autotemp is calculated by (mintemp + factor * mm_per_sec), capped to maxtemp.
  414. *
  415. * Enable Autotemp Mode with M104/M109 F<factor> S<mintemp> B<maxtemp>.
  416. * Disable by sending M104/M109 with no F parameter (or F0 with AUTOTEMP_PROPORTIONAL).
  417. */
  418. #define AUTOTEMP
  419. #if ENABLED(AUTOTEMP)
  420. #define AUTOTEMP_OLDWEIGHT 0.98
  421. // Turn on AUTOTEMP on M104/M109 by default using proportions set here
  422. //#define AUTOTEMP_PROPORTIONAL
  423. #if ENABLED(AUTOTEMP_PROPORTIONAL)
  424. #define AUTOTEMP_MIN_P 0 // (°C) Added to the target temperature
  425. #define AUTOTEMP_MAX_P 5 // (°C) Added to the target temperature
  426. #define AUTOTEMP_FACTOR_P 1 // Apply this F parameter by default (overridden by M104/M109 F)
  427. #endif
  428. #endif
  429.  
  430. // Show Temperature ADC value
  431. // Enable for M105 to include ADC values read from temperature sensors.
  432. //#define SHOW_TEMP_ADC_VALUES
  433.  
  434. /**
  435. * High Temperature Thermistor Support
  436. *
  437. * Thermistors able to support high temperature tend to have a hard time getting
  438. * good readings at room and lower temperatures. This means TEMP_SENSOR_X_RAW_LO_TEMP
  439. * will probably be caught when the heating element first turns on during the
  440. * preheating process, which will trigger a min_temp_error as a safety measure
  441. * and force stop everything.
  442. * To circumvent this limitation, we allow for a preheat time (during which,
  443. * min_temp_error won't be triggered) and add a min_temp buffer to handle
  444. * aberrant readings.
  445. *
  446. * If you want to enable this feature for your hotend thermistor(s)
  447. * uncomment and set values > 0 in the constants below
  448. */
  449.  
  450. // The number of consecutive low temperature errors that can occur
  451. // before a min_temp_error is triggered. (Shouldn't be more than 10.)
  452. //#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
  453.  
  454. // The number of milliseconds a hotend will preheat before starting to check
  455. // the temperature. This value should NOT be set to the time it takes the
  456. // hot end to reach the target temperature, but the time it takes to reach
  457. // the minimum temperature your thermistor can read. The lower the better/safer.
  458. // This shouldn't need to be more than 30 seconds (30000)
  459. //#define MILLISECONDS_PREHEAT_TIME 0
  460.  
  461. // @section extruder
  462.  
  463. // Extruder runout prevention.
  464. // If the machine is idle and the temperature over MINTEMP
  465. // then extrude some filament every couple of SECONDS.
  466. //#define EXTRUDER_RUNOUT_PREVENT
  467. #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
  468. #define EXTRUDER_RUNOUT_MINTEMP 190
  469. #define EXTRUDER_RUNOUT_SECONDS 30
  470. #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/min)
  471. #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm)
  472. #endif
  473.  
  474. /**
  475. * Hotend Idle Timeout
  476. * Prevent filament in the nozzle from charring and causing a critical jam.
  477. */
  478. #define HOTEND_IDLE_TIMEOUT
  479. #if ENABLED(HOTEND_IDLE_TIMEOUT)
  480. #define HOTEND_IDLE_TIMEOUT_SEC (10*60) // (seconds) Time without extruder movement to trigger protection
  481. #define HOTEND_IDLE_MIN_TRIGGER 180 // (°C) Minimum temperature to enable hotend protection
  482. #define HOTEND_IDLE_NOZZLE_TARGET 0 // (°C) Safe temperature for the nozzle after timeout
  483. #define HOTEND_IDLE_BED_TARGET 0 // (°C) Safe temperature for the bed after timeout
  484. #endif
  485.  
  486. // @section temperature
  487.  
  488. // Calibration for AD595 / AD8495 sensor to adjust temperature measurements.
  489. // The final temperature is calculated as (measuredTemp * GAIN) + OFFSET.
  490. #define TEMP_SENSOR_AD595_OFFSET 0.0
  491. #define TEMP_SENSOR_AD595_GAIN 1.0
  492. #define TEMP_SENSOR_AD8495_OFFSET 0.0
  493. #define TEMP_SENSOR_AD8495_GAIN 1.0
  494.  
  495. /**
  496. * Controller Fan
  497. * To cool down the stepper drivers and MOSFETs.
  498. *
  499. * The fan turns on automatically whenever any driver is enabled and turns
  500. * off (or reduces to idle speed) shortly after drivers are turned off.
  501. */
  502. //#define USE_CONTROLLER_FAN
  503. #if ENABLED(USE_CONTROLLER_FAN)
  504. //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan
  505. //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered
  506. //#define CONTROLLER_FAN_IGNORE_Z // Ignore Z stepper. Useful when stepper timeout is disabled.
  507. #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.)
  508. #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled
  509. #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled
  510. #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors
  511.  
  512.  
  513.  
  514.  
  515. //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
  516. #if ENABLED(CONTROLLER_FAN_EDITABLE)
  517. #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
  518. #endif
  519. #endif
  520.  
  521. // When first starting the main fan, run it at full speed for the
  522. // given number of milliseconds. This gets the fan spinning reliably
  523. // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
  524. //#define FAN_KICKSTART_TIME 100
  525.  
  526. // Some coolers may require a non-zero "off" state.
  527. //#define FAN_OFF_PWM 1
  528.  
  529. /**
  530. * PWM Fan Scaling
  531. *
  532. * Define the min/max speeds for PWM fans (as set with M106).
  533. *
  534. * With these options the M106 0-255 value range is scaled to a subset
  535. * to ensure that the fan has enough power to spin, or to run lower
  536. * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
  537. * Value 0 always turns off the fan.
  538. *
  539. * Define one or both of these to override the default 0-255 range.
  540. */
  541. #define FAN_MIN_PWM 80
  542. //#define FAN_MAX_PWM 128
  543.  
  544. /**
  545. * FAST PWM FAN Settings
  546. *
  547. * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h)
  548. * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a
  549. * frequency as close as possible to the desired frequency.
  550. *
  551. * FAST_PWM_FAN_FREQUENCY [undefined by default]
  552. * Set this to your desired frequency.
  553. * If left undefined this defaults to F = F_CPU/(2*255*1)
  554. * i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
  555. * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
  556.  
  557.  
  558.  
  559. * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
  560.  
  561. *
  562. * USE_OCR2A_AS_TOP [undefined by default]
  563. * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
  564. * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz]
  565. * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz]
  566. * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of
  567. * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
  568. * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies.
  569. */
  570.  
  571. #if ENABLED(FAST_PWM_FAN)
  572. //#define FAST_PWM_FAN_FREQUENCY 31400
  573. //#define USE_OCR2A_AS_TOP
  574.  
  575.  
  576.  
  577.  
  578.  
  579.  
  580.  
  581. #endif
  582.  
  583. /**
  584. * Use one of the PWM fans as a redundant part-cooling fan
  585. */
  586. //#define REDUNDANT_PART_COOLING_FAN 2 // Index of the fan to sync with FAN 0.
  587.  
  588. // @section extruder
  589.  
  590. /**
  591. * Extruder cooling fans
  592. *
  593. * Extruder auto fans automatically turn on when their extruders'
  594. * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE.
  595. *
  596. * Your board's pins file specifies the recommended pins. Override those here
  597. * or set to -1 to disable completely.
  598. *
  599. * Multiple extruders can be assigned to the same pin in which case
  600. * the fan will turn on when any selected extruder is above the threshold.
  601. */
  602. #define E0_AUTO_FAN_PIN -1
  603. #define E1_AUTO_FAN_PIN -1
  604. #define E2_AUTO_FAN_PIN -1
  605. #define E3_AUTO_FAN_PIN -1
  606. #define E4_AUTO_FAN_PIN -1
  607. #define E5_AUTO_FAN_PIN -1
  608. #define E6_AUTO_FAN_PIN -1
  609. #define E7_AUTO_FAN_PIN -1
  610. #define CHAMBER_AUTO_FAN_PIN -1
  611. #define COOLER_AUTO_FAN_PIN -1
  612. #define COOLER_FAN_PIN -1
  613.  
  614. #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
  615. #define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed
  616. #define CHAMBER_AUTO_FAN_TEMPERATURE 30
  617. #define CHAMBER_AUTO_FAN_SPEED 255
  618. #define COOLER_AUTO_FAN_TEMPERATURE 18
  619. #define COOLER_AUTO_FAN_SPEED 255
  620.  
  621. /**
  622.  
  623.  
  624.  
  625.  
  626.  
  627.  
  628.  
  629.  
  630.  
  631.  
  632.  
  633.  
  634.  
  635.  
  636.  
  637.  
  638.  
  639.  
  640.  
  641.  
  642.  
  643.  
  644.  
  645.  
  646.  
  647.  
  648.  
  649.  
  650.  
  651.  
  652.  
  653.  
  654.  
  655.  
  656. * Part-Cooling Fan Multiplexer
  657. *
  658. * This feature allows you to digitally multiplex the fan output.
  659. * The multiplexer is automatically switched at tool-change.
  660. * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans.
  661. */
  662. #define FANMUX0_PIN -1
  663. #define FANMUX1_PIN -1
  664. #define FANMUX2_PIN -1
  665.  
  666. /**
  667. * M355 Case Light on-off / brightness
  668. */
  669. //#define CASE_LIGHT_ENABLE
  670. #if ENABLED(CASE_LIGHT_ENABLE)
  671. //#define CASE_LIGHT_PIN 4 // Override the default pin if needed
  672. #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
  673. #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
  674. #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
  675. //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting.
  676. //#define CASE_LIGHT_MAX_PWM 128 // Limit PWM duty cycle (0-255)
  677. //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu
  678. #if ENABLED(NEOPIXEL_LED)
  679. //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light
  680. #endif
  681. #if EITHER(RGB_LED, RGBW_LED)
  682. //#define CASE_LIGHT_USE_RGB_LED // Use RGB / RGBW LED as case light
  683. #endif
  684. #if EITHER(CASE_LIGHT_USE_NEOPIXEL, CASE_LIGHT_USE_RGB_LED)
  685. #define CASE_LIGHT_DEFAULT_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
  686. #endif
  687. #endif
  688.  
  689. // @section homing
  690.  
  691. // If you want endstops to stay on (by default) even when not homing
  692. // enable this option. Override at any time with M120, M121.
  693. //#define ENDSTOPS_ALWAYS_ON_DEFAULT
  694.  
  695. // @section extras
  696.  
  697. //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
  698.  
  699. // Employ an external closed loop controller. Override pins here if needed.
  700. //#define EXTERNAL_CLOSED_LOOP_CONTROLLER
  701. #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
  702. //#define CLOSED_LOOP_ENABLE_PIN -1
  703. //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
  704. #endif
  705.  
  706. /**
  707. * Dual Steppers / Dual Endstops
  708. *
  709. * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes.
  710. *
  711. * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to
  712. * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop
  713. * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug
  714. * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'.
  715. *
  716. * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors
  717. * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error
  718. * in X2. Dual endstop offsets can be set at runtime with 'M666 X<offset> Y<offset> Z<offset>'.
  719. */
  720.  
  721. //#define X_DUAL_STEPPER_DRIVERS
  722. #if ENABLED(X_DUAL_STEPPER_DRIVERS)
  723. //#define INVERT_X2_VS_X_DIR // Enable if X2 direction signal is opposite to X
  724. //#define X_DUAL_ENDSTOPS
  725. #if ENABLED(X_DUAL_ENDSTOPS)
  726. #define X2_USE_ENDSTOP _XMAX_
  727. #define X2_ENDSTOP_ADJUSTMENT 0
  728. #endif
  729. #endif
  730.  
  731. //#define Y_DUAL_STEPPER_DRIVERS
  732. #if ENABLED(Y_DUAL_STEPPER_DRIVERS)
  733. //#define INVERT_Y2_VS_Y_DIR // Enable if Y2 direction signal is opposite to Y
  734. //#define Y_DUAL_ENDSTOPS
  735. #if ENABLED(Y_DUAL_ENDSTOPS)
  736. #define Y2_USE_ENDSTOP _YMAX_
  737. #define Y2_ENDSTOP_ADJUSTMENT 0
  738. #endif
  739. #endif
  740.  
  741. //
  742. // For Z set the number of stepper drivers
  743. //
  744. #define NUM_Z_STEPPER_DRIVERS 1 // (1-4) Z options change based on how many
  745.  
  746. #if NUM_Z_STEPPER_DRIVERS > 1
  747. // Enable if Z motor direction signals are the opposite of Z1
  748. //#define INVERT_Z2_VS_Z_DIR
  749. //#define INVERT_Z3_VS_Z_DIR
  750. //#define INVERT_Z4_VS_Z_DIR
  751.  
  752. //#define Z_MULTI_ENDSTOPS
  753. #if ENABLED(Z_MULTI_ENDSTOPS)
  754. #define Z2_USE_ENDSTOP _XMAX_
  755. #define Z2_ENDSTOP_ADJUSTMENT 0
  756. #if NUM_Z_STEPPER_DRIVERS >= 3
  757. #define Z3_USE_ENDSTOP _YMAX_
  758. #define Z3_ENDSTOP_ADJUSTMENT 0
  759. #endif
  760. #if NUM_Z_STEPPER_DRIVERS >= 4
  761. #define Z4_USE_ENDSTOP _ZMAX_
  762. #define Z4_ENDSTOP_ADJUSTMENT 0
  763. #endif
  764. #endif
  765. #endif
  766.  
  767. // Drive the E axis with two synchronized steppers
  768. //#define E_DUAL_STEPPER_DRIVERS
  769. #if ENABLED(E_DUAL_STEPPER_DRIVERS)
  770. //#define INVERT_E1_VS_E0_DIR // Enable if the E motors need opposite DIR states
  771. #endif
  772.  
  773. /**
  774. * Dual X Carriage
  775. *
  776. * This setup has two X carriages that can move independently, each with its own hotend.
  777. * The carriages can be used to print an object with two colors or materials, or in
  778. * "duplication mode" it can print two identical or X-mirrored objects simultaneously.
  779. * The inactive carriage is parked automatically to prevent oozing.
  780. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis.
  781. * By default the X2 stepper is assigned to the first unused E plug on the board.
  782. *
  783. * The following Dual X Carriage modes can be selected with M605 S<mode>:
  784. *
  785. * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel
  786. * results as long as it supports dual X-carriages. (M605 S0)
  787. *
  788. * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so
  789. * that additional slicer support is not required. (M605 S1)
  790. *
  791. * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with
  792. * the first X-carriage and extruder, to print 2 copies of the same object at the same time.
  793. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and
  794. * follow with M605 S2 to initiate duplicated movement.
  795. *
  796. * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates
  797. * the movement of the first except the second extruder is reversed in the X axis.
  798. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and
  799. * follow with M605 S3 to initiate mirrored movement.
  800. */
  801. //#define DUAL_X_CARRIAGE
  802. #if ENABLED(DUAL_X_CARRIAGE)
  803. #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS
  804. #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage
  805. #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage
  806. #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed
  807. #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position
  808. #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS.
  809. // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
  810. // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
  811. // without modifying the firmware (through the "M218 T1 X???" command).
  812. // Remember: you should set the second extruder x-offset to 0 in your slicer.
  813.  
  814. // This is the default power-up mode which can be later using M605.
  815. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE
  816.  
  817. // Default x offset in duplication mode (typically set to half print bed width)
  818. #define DEFAULT_DUPLICATION_X_OFFSET 100
  819.  
  820. // Default action to execute following M605 mode change commands. Typically G28X to apply new mode.
  821. //#define EVENT_GCODE_IDEX_AFTER_MODECHANGE "G28X"
  822. #endif
  823.  
  824.  
  825.  
  826.  
  827.  
  828.  
  829.  
  830.  
  831.  
  832.  
  833.  
  834.  
  835.  
  836.  
  837.  
  838.  
  839.  
  840.  
  841.  
  842.  
  843.  
  844.  
  845.  
  846.  
  847.  
  848.  
  849.  
  850.  
  851.  
  852.  
  853.  
  854.  
  855.  
  856.  
  857.  
  858.  
  859.  
  860.  
  861.  
  862.  
  863.  
  864.  
  865.  
  866.  
  867.  
  868.  
  869.  
  870.  
  871.  
  872.  
  873.  
  874.  
  875.  
  876.  
  877.  
  878.  
  879.  
  880.  
  881.  
  882.  
  883.  
  884.  
  885.  
  886.  
  887.  
  888.  
  889.  
  890.  
  891.  
  892.  
  893.  
  894.  
  895. // Activate a solenoid on the active extruder with M380. Disable all with M381.
  896. // Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
  897. //#define EXT_SOLENOID
  898.  
  899. // @section homing
  900.  
  901. /**
  902. * Homing Procedure
  903. * Homing (G28) does an indefinite move towards the endstops to establish
  904. * the position of the toolhead relative to the workspace.
  905. */
  906.  
  907. //#define SENSORLESS_BACKOFF_MM { 2, 2, 0 } // (mm) Backoff from endstops before sensorless homing
  908.  
  909. #define HOMING_BUMP_MM { 5, 5, 2 } // (mm) Backoff from endstops after first bump
  910. #define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)
  911.  
  912. //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (mm) Backoff from endstops after homing
  913.  
  914. #define QUICK_HOME // If G28 contains XY do a diagonal move first
  915. //#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X
  916. //#define HOME_Z_FIRST // Home Z first. Requires a Z-MIN endstop (not a probe).
  917. //#define CODEPENDENT_XY_HOMING // If X/Y can't home without homing Y/X first
  918.  
  919. // @section bltouch
  920.  
  921. #if ENABLED(BLTOUCH)
  922. /**
  923. * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
  924. * Do not activate settings that the probe might not understand. Clones might misunderstand
  925. * advanced commands.
  926. *
  927. * Note: If the probe is not deploying, do a "Reset" and "Self-Test" and then check the
  928. * wiring of the BROWN, RED and ORANGE wires.
  929. *
  930. * Note: If the trigger signal of your probe is not being recognized, it has been very often
  931. * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
  932. * like they would be with a real switch. So please check the wiring first.
  933. *
  934. * Settings for all BLTouch and clone probes:
  935. */
  936.  
  937. // Safety: The probe needs time to recognize the command.
  938. // Minimum command delay (ms). Enable and increase if needed.
  939. //#define BLTOUCH_DELAY 500
  940.  
  941. /**
  942. * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
  943. */
  944.  
  945. // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
  946. // in special cases, like noisy or filtered input configurations.
  947. //#define BLTOUCH_FORCE_SW_MODE
  948.  
  949. /**
  950. * Settings for BLTouch Smart 3.0 and 3.1
  951. * Summary:
  952. * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
  953. * - High-Speed mode
  954. * - Disable LCD voltage options
  955. */
  956.  
  957. /**
  958. * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
  959. * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
  960. * If disabled, OD mode is the hard-coded default on 3.0
  961. * On startup, Marlin will compare its eeprom to this value. If the selected mode
  962. * differs, a mode set eeprom write will be completed at initialization.
  963. * Use the option below to force an eeprom write to a V3.1 probe regardless.
  964. */
  965. //#define BLTOUCH_SET_5V_MODE
  966.  
  967. /**
  968. * Safety: Activate if connecting a probe with an unknown voltage mode.
  969. * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
  970. * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
  971. * To preserve the life of the probe, use this once then turn it off and re-flash.
  972. */
  973. //#define BLTOUCH_FORCE_MODE_SET
  974.  
  975. /**
  976. * Use "HIGH SPEED" mode for probing.
  977. * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
  978. * This feature was designed for Deltabots with very fast Z moves; however, higher speed Cartesians
  979. * might be able to use it. If the machine can't raise Z fast enough the BLTouch may go into ALARM.
  980.  
  981.  
  982. */
  983. //#define BLTOUCH_HS_MODE
  984.  
  985. // Safety: Enable voltage mode settings in the LCD menu.
  986. //#define BLTOUCH_LCD_VOLTAGE_MENU
  987.  
  988. #endif // BLTOUCH
  989.  
  990. // @section extras
  991.  
  992. /**
  993. * Z Steppers Auto-Alignment
  994. * Add the G34 command to align multiple Z steppers using a bed probe.
  995. */
  996. //#define Z_STEPPER_AUTO_ALIGN
  997. #if ENABLED(Z_STEPPER_AUTO_ALIGN)
  998.  
  999. // Define probe X and Y positions for Z1, Z2 [, Z3 [, Z4]]
  1000.  
  1001. // If not defined, probe limits will be used.
  1002. // Override with 'M422 S<index> X<pos> Y<pos>'
  1003.  
  1004. //#define Z_STEPPER_ALIGN_XY { { 10, 190 }, { 100, 10 }, { 190, 190 } }
  1005.  
  1006. /**
  1007. * Orientation for the automatically-calculated probe positions.
  1008. * Override Z stepper align points with 'M422 S<index> X<pos> Y<pos>'
  1009. *
  1010. * 2 Steppers: (0) (1)
  1011. * | | 2 |
  1012. * | 1 2 | |
  1013. * | | 1 |
  1014. *
  1015. * 3 Steppers: (0) (1) (2) (3)
  1016. * | 3 | 1 | 2 1 | 2 |
  1017. * | | 3 | | 3 |
  1018. * | 1 2 | 2 | 3 | 1 |
  1019. *
  1020. * 4 Steppers: (0) (1) (2) (3)
  1021. * | 4 3 | 1 4 | 2 1 | 3 2 |
  1022. * | | | | |
  1023. * | 1 2 | 2 3 | 3 4 | 4 1 |
  1024. */
  1025. #ifndef Z_STEPPER_ALIGN_XY
  1026. //#define Z_STEPPERS_ORIENTATION 0
  1027. #endif
  1028.  
  1029.  
  1030. // Provide Z stepper positions for more rapid convergence in bed alignment.
  1031. // Requires triple stepper drivers (i.e., set NUM_Z_STEPPER_DRIVERS to 3)
  1032. //#define Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS
  1033. #if ENABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
  1034. // Define Stepper XY positions for Z1, Z2, Z3 corresponding to
  1035. // the Z screw positions in the bed carriage.
  1036. // Define one position per Z stepper in stepper driver order.
  1037.  
  1038. #define Z_STEPPER_ALIGN_STEPPER_XY { { 210.7, 102.5 }, { 152.6, 220.0 }, { 94.5, 102.5 } }
  1039. #else
  1040.  
  1041. // Amplification factor. Used to scale the correction step up or down in case
  1042. // the stepper (spindle) position is farther out than the test point.
  1043. #define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
  1044. #endif
  1045.  
  1046. // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
  1047. #define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
  1048. #define Z_STEPPER_ALIGN_ITERATIONS 5 // Number of iterations to apply during alignment
  1049. #define Z_STEPPER_ALIGN_ACC 0.01 // Stop iterating early if the accuracy is better than this
  1050. #define RESTORE_LEVELING_AFTER_G34 // Restore leveling after G34 is done?
  1051. // After G34, re-home Z (G28 Z) or just calculate it from the last probe heights?
  1052. // Re-homing might be more precise in reproducing the actual 'G28 Z' homing height, especially on an uneven bed.
  1053. #define HOME_AFTER_G34
  1054. #endif
  1055.  
  1056. //
  1057. // Add the G35 command to read bed corners to help adjust screws. Requires a bed probe.
  1058. //
  1059. //#define ASSISTED_TRAMMING
  1060. #if ENABLED(ASSISTED_TRAMMING)
  1061.  
  1062. // Define positions for probe points.
  1063. #define TRAMMING_POINT_XY { { 20, 20 }, { 180, 20 }, { 180, 180 }, { 20, 180 } }
  1064.  
  1065. // Define position names for probe points.
  1066. #define TRAMMING_POINT_NAME_1 "Front-Left"
  1067. #define TRAMMING_POINT_NAME_2 "Front-Right"
  1068. #define TRAMMING_POINT_NAME_3 "Back-Right"
  1069. #define TRAMMING_POINT_NAME_4 "Back-Left"
  1070.  
  1071. #define RESTORE_LEVELING_AFTER_G35 // Enable to restore leveling setup after operation
  1072. //#define REPORT_TRAMMING_MM // Report Z deviation (mm) for each point relative to the first
  1073.  
  1074. //#define ASSISTED_TRAMMING_WIZARD // Add a Tramming Wizard to the LCD menu
  1075.  
  1076. //#define ASSISTED_TRAMMING_WAIT_POSITION { X_CENTER, Y_CENTER, 30 } // Move the nozzle out of the way for adjustment
  1077.  
  1078. /**
  1079. * Screw thread:
  1080. * M3: 30 = Clockwise, 31 = Counter-Clockwise
  1081. * M4: 40 = Clockwise, 41 = Counter-Clockwise
  1082. * M5: 50 = Clockwise, 51 = Counter-Clockwise
  1083. */
  1084. #define TRAMMING_SCREW_THREAD 30
  1085.  
  1086. #endif
  1087.  
  1088. // @section motion
  1089.  
  1090. #define AXIS_RELATIVE_MODES { false, false, false, false }
  1091.  
  1092. // Add a Duplicate option for well-separated conjoined nozzles
  1093. //#define MULTI_NOZZLE_DUPLICATION
  1094.  
  1095. // By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
  1096. #define INVERT_X_STEP_PIN false
  1097. #define INVERT_Y_STEP_PIN false
  1098. #define INVERT_Z_STEP_PIN false
  1099. #define INVERT_I_STEP_PIN false
  1100. #define INVERT_J_STEP_PIN false
  1101. #define INVERT_K_STEP_PIN false
  1102. #define INVERT_E_STEP_PIN false
  1103.  
  1104. /**
  1105. * Idle Stepper Shutdown
  1106. * Set DISABLE_INACTIVE_? 'true' to shut down axis steppers after an idle period.
  1107. * The Deactive Time can be overridden with M18 and M84. Set to 0 for No Timeout.
  1108. */
  1109. #define DEFAULT_STEPPER_DEACTIVE_TIME 120
  1110. #define DISABLE_INACTIVE_X true
  1111. #define DISABLE_INACTIVE_Y true
  1112. #define DISABLE_INACTIVE_Z true // Set 'false' if the nozzle could fall onto your printed part!
  1113. #define DISABLE_INACTIVE_I true
  1114. #define DISABLE_INACTIVE_J true
  1115. #define DISABLE_INACTIVE_K true
  1116. #define DISABLE_INACTIVE_E true
  1117.  
  1118. // Default Minimum Feedrates for printing and travel moves
  1119. #define DEFAULT_MINIMUMFEEDRATE 0.0 // (mm/s) Minimum feedrate. Set with M205 S.
  1120. #define DEFAULT_MINTRAVELFEEDRATE 0.0 // (mm/s) Minimum travel feedrate. Set with M205 T.
  1121.  
  1122. // Minimum time that a segment needs to take as the buffer gets emptied
  1123. #define DEFAULT_MINSEGMENTTIME 20000 // (µs) Set with M205 B.
  1124.  
  1125. // Slow down the machine if the lookahead buffer is (by default) half full.
  1126. // Increase the slowdown divisor for larger buffer sizes.
  1127. #define SLOWDOWN
  1128. #if ENABLED(SLOWDOWN)
  1129. #define SLOWDOWN_DIVISOR 4
  1130. #endif
  1131.  
  1132. /**
  1133. * XY Frequency limit
  1134. * Reduce resonance by limiting the frequency of small zigzag infill moves.
  1135. * See https://hydraraptor.blogspot.com/2010/12/frequency-limit.html
  1136. * Use M201 F<freq> G<min%> to change limits at runtime.
  1137. */
  1138. //#define XY_FREQUENCY_LIMIT 10 // (Hz) Maximum frequency of small zigzag infill moves. Set with M201 F<hertz>.
  1139. #ifdef XY_FREQUENCY_LIMIT
  1140. #define XY_FREQUENCY_MIN_PERCENT 5 // (percent) Minimum FR percentage to apply. Set with M201 G<min%>.
  1141. #endif
  1142.  
  1143. // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
  1144. // of the buffer and all stops. This should not be much greater than zero and should only be changed
  1145. // if unwanted behavior is observed on a user's machine when running at very slow speeds.
  1146. #define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
  1147.  
  1148. //
  1149. // Backlash Compensation
  1150. // Adds extra movement to axes on direction-changes to account for backlash.
  1151. //
  1152. //#define BACKLASH_COMPENSATION
  1153. #if ENABLED(BACKLASH_COMPENSATION)
  1154. // Define values for backlash distance and correction.
  1155. // If BACKLASH_GCODE is enabled these values are the defaults.
  1156. #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) One value for each linear axis
  1157. #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction
  1158.  
  1159. // Add steps for motor direction changes on CORE kinematics
  1160. //#define CORE_BACKLASH
  1161.  
  1162. // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments
  1163. // to reduce print artifacts. (Enabling this is costly in memory and computation!)
  1164. //#define BACKLASH_SMOOTHING_MM 3 // (mm)
  1165.  
  1166. // Add runtime configuration and tuning of backlash values (M425)
  1167. //#define BACKLASH_GCODE
  1168.  
  1169. #if ENABLED(BACKLASH_GCODE)
  1170. // Measure the Z backlash when probing (G29) and set with "M425 Z"
  1171. #define MEASURE_BACKLASH_WHEN_PROBING
  1172.  
  1173. #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING)
  1174. // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT
  1175. // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION
  1176. // increments while checking for the contact to be broken.
  1177. #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm)
  1178. #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm)
  1179. #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_FEEDRATE_SLOW // (mm/min)
  1180. #endif
  1181. #endif
  1182. #endif
  1183.  
  1184. /**
  1185. * Automatic backlash, position and hotend offset calibration
  1186. *
  1187. * Enable G425 to run automatic calibration using an electrically-
  1188. * conductive cube, bolt, or washer mounted on the bed.
  1189. *
  1190. * G425 uses the probe to touch the top and sides of the calibration object
  1191. * on the bed and measures and/or correct positional offsets, axis backlash
  1192. * and hotend offsets.
  1193. *
  1194. * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within
  1195. * ±5mm of true values for G425 to succeed.
  1196. */
  1197. //#define CALIBRATION_GCODE
  1198. #if ENABLED(CALIBRATION_GCODE)
  1199.  
  1200. //#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
  1201. //#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
  1202.  
  1203. #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm
  1204.  
  1205. #define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
  1206. #define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
  1207. #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
  1208.  
  1209. // The following parameters refer to the conical section of the nozzle tip.
  1210. #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
  1211. #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
  1212.  
  1213. // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM).
  1214. //#define CALIBRATION_REPORTING
  1215.  
  1216. // The true location and dimension the cube/bolt/washer on the bed.
  1217. #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
  1218. #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
  1219.  
  1220. // Comment out any sides which are unreachable by the probe. For best
  1221. // auto-calibration results, all sides must be reachable.
  1222. #define CALIBRATION_MEASURE_RIGHT
  1223. #define CALIBRATION_MEASURE_FRONT
  1224. #define CALIBRATION_MEASURE_LEFT
  1225. #define CALIBRATION_MEASURE_BACK
  1226.  
  1227. //#define CALIBRATION_MEASURE_IMIN
  1228. //#define CALIBRATION_MEASURE_IMAX
  1229. //#define CALIBRATION_MEASURE_JMIN
  1230. //#define CALIBRATION_MEASURE_JMAX
  1231. //#define CALIBRATION_MEASURE_KMIN
  1232. //#define CALIBRATION_MEASURE_KMAX
  1233.  
  1234. // Probing at the exact top center only works if the center is flat. If
  1235. // probing on a screwhead or hollow washer, probe near the edges.
  1236. //#define CALIBRATION_MEASURE_AT_TOP_EDGES
  1237.  
  1238. // Define the pin to read during calibration
  1239. #ifndef CALIBRATION_PIN
  1240. //#define CALIBRATION_PIN -1 // Define here to override the default pin
  1241. #define CALIBRATION_PIN_INVERTING false // Set to true to invert the custom pin
  1242. //#define CALIBRATION_PIN_PULLDOWN
  1243. #define CALIBRATION_PIN_PULLUP
  1244. #endif
  1245. #endif
  1246.  
  1247. /**
  1248. * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies
  1249. * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible
  1250. * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the
  1251. * lowest stepping frequencies.
  1252. */
  1253. #define ADAPTIVE_STEP_SMOOTHING
  1254.  
  1255. /**
  1256. * Custom Microstepping
  1257. * Override as-needed for your setup. Up to 3 MS pins are supported.
  1258. */
  1259. //#define MICROSTEP1 LOW,LOW,LOW
  1260. //#define MICROSTEP2 HIGH,LOW,LOW
  1261. //#define MICROSTEP4 LOW,HIGH,LOW
  1262. //#define MICROSTEP8 HIGH,HIGH,LOW
  1263. //#define MICROSTEP16 LOW,LOW,HIGH
  1264. //#define MICROSTEP32 HIGH,LOW,HIGH
  1265.  
  1266. // Microstep settings (Requires a board with pins named X_MS1, X_MS2, etc.)
  1267. #define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
  1268.  
  1269. /**
  1270. * @section stepper motor current
  1271. *
  1272. * Some boards have a means of setting the stepper motor current via firmware.
  1273. *
  1274. * The power on motor currents are set by:
  1275. * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2
  1276. * known compatible chips: A4982
  1277. * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H
  1278. * known compatible chips: AD5206
  1279. * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
  1280. * known compatible chips: MCP4728
  1281. * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE
  1282. * known compatible chips: MCP4451, MCP4018
  1283. *
  1284. * Motor currents can also be set by M907 - M910 and by the LCD.
  1285. * M907 - applies to all.
  1286. * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
  1287. * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
  1288. */
  1289. //#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps
  1290. //#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
  1291. //#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
  1292.  
  1293. /**
  1294. * I2C-based DIGIPOTs (e.g., Azteeg X3 Pro)
  1295. */
  1296. //#define DIGIPOT_MCP4018 // Requires https://github.com/felias-fogg/SlowSoftI2CMaster
  1297. //#define DIGIPOT_MCP4451
  1298. #if EITHER(DIGIPOT_MCP4018, DIGIPOT_MCP4451)
  1299. #define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT:4 AZTEEG_X3_PRO:8 MKS_SBASE:5 MIGHTYBOARD_REVE:5
  1300.  
  1301. // Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS.
  1302. // These correspond to the physical drivers, so be mindful if the order is changed.
  1303. #define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO
  1304.  
  1305. //#define DIGIPOT_USE_RAW_VALUES // Use DIGIPOT_MOTOR_CURRENT raw wiper values (instead of A4988 motor currents)
  1306.  
  1307. /**
  1308. * Common slave addresses:
  1309. *
  1310. * A (A shifted) B (B shifted) IC
  1311. * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451
  1312. * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451
  1313. * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451
  1314. * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451
  1315. * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018
  1316. */
  1317. //#define DIGIPOT_I2C_ADDRESS_A 0x2C // Unshifted slave address for first DIGIPOT
  1318. //#define DIGIPOT_I2C_ADDRESS_B 0x2D // Unshifted slave address for second DIGIPOT
  1319. #endif
  1320.  
  1321. //===========================================================================
  1322. //=============================Additional Features===========================
  1323. //===========================================================================
  1324.  
  1325. // @section lcd
  1326.  
  1327. #if EITHER(IS_ULTIPANEL, EXTENSIBLE_UI)
  1328. #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // (mm/min) Feedrates for manual moves along X, Y, Z, E from panel
  1329. #define FINE_MANUAL_MOVE 0.025 // (mm) Smallest manual move (< 0.1mm) applying to Z on most machines
  1330. #if IS_ULTIPANEL
  1331. #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
  1332. #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen
  1333. #endif
  1334. #endif
  1335.  
  1336. // Change values more rapidly when the encoder is rotated faster
  1337. #define ENCODER_RATE_MULTIPLIER
  1338. #if ENABLED(ENCODER_RATE_MULTIPLIER)
  1339. #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed
  1340. #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed
  1341. #endif
  1342.  
  1343. // Play a beep when the feedrate is changed from the Status Screen
  1344. //#define BEEP_ON_FEEDRATE_CHANGE
  1345. #if ENABLED(BEEP_ON_FEEDRATE_CHANGE)
  1346. #define FEEDRATE_CHANGE_BEEP_DURATION 10
  1347. #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440
  1348. #endif
  1349.  
  1350. #if HAS_LCD_MENU
  1351.  
  1352.  
  1353.  
  1354.  
  1355.  
  1356. // Add Probe Z Offset calibration to the Z Probe Offsets menu
  1357. #if HAS_BED_PROBE
  1358. #define PROBE_OFFSET_WIZARD
  1359. #if ENABLED(PROBE_OFFSET_WIZARD)
  1360. //
  1361. // Enable to init the Probe Z-Offset when starting the Wizard.
  1362. // Use a height slightly above the estimated nozzle-to-probe Z offset.
  1363. // For example, with an offset of -5, consider a starting height of -4.
  1364. //
  1365. #define PROBE_OFFSET_WIZARD_START_Z -4.0
  1366.  
  1367. // Set a convenient position to do the calibration (probing point and nozzle/bed-distance)
  1368. #define PROBE_OFFSET_WIZARD_XY_POS { X_CENTER, Y_CENTER }
  1369.  
  1370.  
  1371.  
  1372.  
  1373.  
  1374.  
  1375.  
  1376.  
  1377.  
  1378.  
  1379.  
  1380.  
  1381.  
  1382.  
  1383.  
  1384.  
  1385.  
  1386.  
  1387. #endif
  1388. #endif
  1389.  
  1390. // Include a page of printer information in the LCD Main Menu
  1391. #define LCD_INFO_MENU
  1392. #if ENABLED(LCD_INFO_MENU)
  1393. //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
  1394. #endif
  1395.  
  1396. // BACK menu items keep the highlight at the top
  1397. //#define TURBO_BACK_MENU_ITEM
  1398.  
  1399.  
  1400.  
  1401.  
  1402.  
  1403.  
  1404.  
  1405. // Add a mute option to the LCD menu
  1406. #define SOUND_MENU_ITEM
  1407.  
  1408.  
  1409.  
  1410.  
  1411.  
  1412.  
  1413.  
  1414.  
  1415.  
  1416.  
  1417.  
  1418.  
  1419.  
  1420.  
  1421.  
  1422.  
  1423.  
  1424.  
  1425.  
  1426.  
  1427.  
  1428.  
  1429.  
  1430.  
  1431.  
  1432.  
  1433.  
  1434.  
  1435. /**
  1436. * LED Control Menu
  1437. * Add LED Control to the LCD menu
  1438. */
  1439. #define LED_CONTROL_MENU
  1440. #if ENABLED(LED_CONTROL_MENU)
  1441. #define LED_COLOR_PRESETS // Enable the Preset Color menu option
  1442. //#define NEO2_COLOR_PRESETS // Enable a second NeoPixel Preset Color menu option
  1443. #if ENABLED(LED_COLOR_PRESETS)
  1444. #define LED_USER_PRESET_RED 255 // User defined RED value
  1445. #define LED_USER_PRESET_GREEN 128 // User defined GREEN value
  1446. #define LED_USER_PRESET_BLUE 0 // User defined BLUE value
  1447. #define LED_USER_PRESET_WHITE 255 // User defined WHITE value
  1448. #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity
  1449. //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup
  1450. #endif
  1451. #if ENABLED(NEO2_COLOR_PRESETS)
  1452. #define NEO2_USER_PRESET_RED 255 // User defined RED value
  1453. #define NEO2_USER_PRESET_GREEN 128 // User defined GREEN value
  1454. #define NEO2_USER_PRESET_BLUE 0 // User defined BLUE value
  1455. #define NEO2_USER_PRESET_WHITE 255 // User defined WHITE value
  1456. #define NEO2_USER_PRESET_BRIGHTNESS 255 // User defined intensity
  1457. //#define NEO2_USER_PRESET_STARTUP // Have the printer display the user preset color on startup for the second strip
  1458. #endif
  1459. #endif
  1460.  
  1461. // Insert a menu for preheating at the top level to allow for quick access
  1462. //#define PREHEAT_SHORTCUT_MENU_ITEM
  1463.  
  1464. #endif // HAS_LCD_MENU
  1465.  
  1466. #if HAS_DISPLAY
  1467. // The timeout (in ms) to return to the status screen from sub-menus
  1468. //#define LCD_TIMEOUT_TO_STATUS 15000
  1469.  
  1470. #if ENABLED(SHOW_BOOTSCREEN)
  1471. #define BOOTSCREEN_TIMEOUT 0 // (ms) Total Duration to display the boot screen(s)
  1472. #if EITHER(HAS_MARLINUI_U8GLIB, TFT_COLOR_UI)
  1473. #define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving lots of flash)
  1474. #endif
  1475. #endif
  1476.  
  1477. // Scroll a longer status message into view
  1478. #define STATUS_MESSAGE_SCROLLING
  1479.  
  1480. // On the Info Screen, display XY with one decimal place when possible
  1481. //#define LCD_DECIMAL_SMALL_XY
  1482.  
  1483. // Add an 'M73' G-code to set the current percentage
  1484. #define LCD_SET_PROGRESS_MANUALLY
  1485.  
  1486. // Show the E position (filament used) during printing
  1487. //#define LCD_SHOW_E_TOTAL
  1488. #endif
  1489.  
  1490.  
  1491. #if EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) && ANY(HAS_MARLINUI_U8GLIB, HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL, EXTENSIBLE_UI)
  1492.  
  1493. #define SHOW_REMAINING_TIME // Display estimated time to completion
  1494. #if ENABLED(SHOW_REMAINING_TIME)
  1495. //#define USE_M73_REMAINING_TIME // Use remaining time from M73 command instead of estimation
  1496. #define ROTATE_PROGRESS_DISPLAY // Display (P)rogress, (E)lapsed, and (R)emaining time
  1497.  
  1498. #endif
  1499.  
  1500. #if EITHER(HAS_MARLINUI_U8GLIB, EXTENSIBLE_UI)
  1501. //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
  1502. #endif
  1503.  
  1504. #if EITHER(HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL)
  1505. //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
  1506. #if ENABLED(LCD_PROGRESS_BAR)
  1507. #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar
  1508. #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message
  1509. #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever)
  1510. //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it
  1511. //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar
  1512. #endif
  1513. #endif
  1514. #endif
  1515.  
  1516. #if ENABLED(SDSUPPORT)
  1517. /**
  1518. * SD Card SPI Speed
  1519. * May be required to resolve "volume init" errors.
  1520. *
  1521. * Enable and set to SPI_HALF_SPEED, SPI_QUARTER_SPEED, or SPI_EIGHTH_SPEED
  1522. * otherwise full speed will be applied.
  1523. *
  1524. * :['SPI_HALF_SPEED', 'SPI_QUARTER_SPEED', 'SPI_EIGHTH_SPEED']
  1525. */
  1526. //#define SD_SPI_SPEED SPI_HALF_SPEED
  1527.  
  1528. // The standard SD detect circuit reads LOW when media is inserted and HIGH when empty.
  1529. // Enable this option and set to HIGH if your SD cards are incorrectly detected.
  1530. //#define SD_DETECT_STATE HIGH
  1531.  
  1532. //#define SD_IGNORE_AT_STARTUP // Don't mount the SD card when starting up
  1533. //#define SDCARD_READONLY // Read-only SD card (to save over 2K of flash)
  1534.  
  1535. //#define GCODE_REPEAT_MARKERS // Enable G-code M808 to set repeat markers and do looping
  1536.  
  1537. #define SD_PROCEDURE_DEPTH 1 // Increase if you need more nested M32 calls
  1538.  
  1539. #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
  1540. #define SD_FINISHED_RELEASECOMMAND "M84" // Use "M84XYE" to keep Z enabled so your bed stays in place
  1541.  
  1542. // Reverse SD sort to show "more recent" files first, according to the card's FAT.
  1543. // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
  1544. #define SDCARD_RATHERRECENTFIRST
  1545.  
  1546. #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing
  1547.  
  1548. //#define NO_SD_AUTOSTART // Remove auto#.g file support completely to save some Flash, SRAM
  1549. //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files
  1550.  
  1551. //#define BROWSE_MEDIA_ON_INSERT // Open the file browser when media is inserted
  1552.  
  1553. #define MEDIA_MENU_AT_TOP // Force the media menu to be listed on the top of the main menu
  1554.  
  1555. #define EVENT_GCODE_SD_ABORT "G28XY\nM84" // G-code to run on SD Abort Print (e.g., "G28XY" or "G27")
  1556.  
  1557. #if ENABLED(PRINTER_EVENT_LEDS)
  1558. #define PE_LEDS_COMPLETED_TIME (30*60) // (seconds) Time to keep the LED "done" color before restoring normal illumination
  1559. #endif
  1560.  
  1561. /**
  1562. * Continue after Power-Loss (Creality3D)
  1563. *
  1564. * Store the current state to the SD Card at the start of each layer
  1565. * during SD printing. If the recovery file is found at boot time, present
  1566. * an option on the LCD screen to continue the print from the last-known
  1567. * point in the file.
  1568. */
  1569. //#define POWER_LOSS_RECOVERY
  1570. #if ENABLED(POWER_LOSS_RECOVERY)
  1571. #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
  1572. //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
  1573. //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
  1574. //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
  1575. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
  1576. //#define POWER_LOSS_PULLUP // Set pullup / pulldown as appropriate for your sensor
  1577. //#define POWER_LOSS_PULLDOWN
  1578. //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
  1579. //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
  1580.  
  1581. // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
  1582. // especially with "vase mode" printing. Set too high and vases cannot be continued.
  1583. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
  1584.  
  1585. // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
  1586. //#define POWER_LOSS_RECOVER_ZHOME
  1587. #if ENABLED(POWER_LOSS_RECOVER_ZHOME)
  1588. //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed
  1589. #endif
  1590. #endif
  1591.  
  1592. /**
  1593. * Sort SD file listings in alphabetical order.
  1594. *
  1595. * With this option enabled, items on SD cards will be sorted
  1596. * by name for easier navigation.
  1597. *
  1598. * By default...
  1599. *
  1600. * - Use the slowest -but safest- method for sorting.
  1601. * - Folders are sorted to the top.
  1602. * - The sort key is statically allocated.
  1603. * - No added G-code (M34) support.
  1604. * - 40 item sorting limit. (Items after the first 40 are unsorted.)
  1605. *
  1606. * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the
  1607. * compiler to calculate the worst-case usage and throw an error if the SRAM
  1608. * limit is exceeded.
  1609. *
  1610. * - SDSORT_USES_RAM provides faster sorting via a static directory buffer.
  1611. * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer.
  1612. * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
  1613. * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
  1614. */
  1615. #define SDCARD_SORT_ALPHA
  1616.  
  1617. // SD Card Sorting options
  1618. #if ENABLED(SDCARD_SORT_ALPHA)
  1619. #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
  1620. #define FOLDER_SORTING -1 // -1=above 0=none 1=below
  1621. #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 G-code.
  1622. #define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting.
  1623. #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
  1624. #define SDSORT_CACHE_NAMES true // Keep sorted items in RAM longer for speedy performance. Most expensive option.
  1625. #define SDSORT_DYNAMIC_RAM true // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
  1626. #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
  1627. // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
  1628. #endif
  1629.  
  1630. // Allow international symbols in long filenames. To display correctly, the
  1631. // LCD's font must contain the characters. Check your selected LCD language.
  1632. //#define UTF_FILENAME_SUPPORT
  1633.  
  1634. // This allows hosts to request long names for files and folders with M33
  1635. #define LONG_FILENAME_HOST_SUPPORT
  1636.  
  1637. // Enable this option to scroll long filenames in the SD card menu
  1638. #define SCROLL_LONG_FILENAMES
  1639.  
  1640. // Leave the heaters on after Stop Print (not recommended!)
  1641. //#define SD_ABORT_NO_COOLDOWN
  1642.  
  1643. /**
  1644. * This option allows you to abort SD printing when any endstop is triggered.
  1645. * This feature must be enabled with "M540 S1" or from the LCD menu.
  1646. * To have any effect, endstops must be enabled during SD printing.
  1647. */
  1648. //#define SD_ABORT_ON_ENDSTOP_HIT
  1649.  
  1650. /**
  1651. * This option makes it easier to print the same SD Card file again.
  1652. * On print completion the LCD Menu will open with the file selected.
  1653. * You can just click to start the print, or navigate elsewhere.
  1654. */
  1655. //#define SD_REPRINT_LAST_SELECTED_FILE
  1656.  
  1657. /**
  1658. * Auto-report SdCard status with M27 S<seconds>
  1659. */
  1660. //#define AUTO_REPORT_SD_STATUS
  1661.  
  1662. /**
  1663. * Support for USB thumb drives using an Arduino USB Host Shield or
  1664. * equivalent MAX3421E breakout board. The USB thumb drive will appear
  1665. * to Marlin as an SD card.
  1666. *
  1667. * The MAX3421E can be assigned the same pins as the SD card reader, with
  1668. * the following pin mapping:
  1669. *
  1670. * SCLK, MOSI, MISO --> SCLK, MOSI, MISO
  1671. * INT --> SD_DETECT_PIN [1]
  1672. * SS --> SDSS
  1673. *
  1674. * [1] On AVR an interrupt-capable pin is best for UHS3 compatibility.
  1675. */
  1676. //#define USB_FLASH_DRIVE_SUPPORT
  1677. #if ENABLED(USB_FLASH_DRIVE_SUPPORT)
  1678. /**
  1679. * USB Host Shield Library
  1680. *
  1681. * - UHS2 uses no interrupts and has been production-tested
  1682. * on a LulzBot TAZ Pro with a 32-bit Archim board.
  1683. *
  1684. * - UHS3 is newer code with better USB compatibility. But it
  1685. * is less tested and is known to interfere with Servos.
  1686. * [1] This requires USB_INTR_PIN to be interrupt-capable.
  1687. */
  1688. //#define USE_UHS2_USB
  1689. //#define USE_UHS3_USB
  1690.  
  1691. /**
  1692. * Native USB Host supported by some boards (USB OTG)
  1693. */
  1694. //#define USE_OTG_USB_HOST
  1695.  
  1696. #if DISABLED(USE_OTG_USB_HOST)
  1697. #define USB_CS_PIN SDSS
  1698. #define USB_INTR_PIN SD_DETECT_PIN
  1699. #endif
  1700. #endif
  1701.  
  1702. /**
  1703. * When using a bootloader that supports SD-Firmware-Flashing,
  1704. * add a menu item to activate SD-FW-Update on the next reboot.
  1705. *
  1706. * Requires ATMEGA2560 (Arduino Mega)
  1707. *
  1708. * Tested with this bootloader:
  1709. * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560
  1710. */
  1711. //#define SD_FIRMWARE_UPDATE
  1712. #if ENABLED(SD_FIRMWARE_UPDATE)
  1713. #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF
  1714. #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0
  1715. #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF
  1716. #endif
  1717.  
  1718.  
  1719.  
  1720.  
  1721.  
  1722.  
  1723.  
  1724.  
  1725.  
  1726. // Add an optimized binary file transfer mode, initiated with 'M28 B1'
  1727. //#define BINARY_FILE_TRANSFER
  1728.  
  1729.  
  1730.  
  1731.  
  1732.  
  1733.  
  1734. /**
  1735. * Set this option to one of the following (or the board's defaults apply):
  1736. *
  1737. * LCD - Use the SD drive in the external LCD controller.
  1738. * ONBOARD - Use the SD drive on the control board.
  1739. * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file).
  1740. *
  1741. * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
  1742. */
  1743. #define SDCARD_CONNECTION ONBOARD
  1744.  
  1745. // Enable if SD detect is rendered useless (e.g., by using an SD extender)
  1746. //#define NO_SD_DETECT
  1747.  
  1748.  
  1749. // Multiple volume support - EXPERIMENTAL.
  1750.  
  1751.  
  1752. //#define MULTI_VOLUME
  1753. #if ENABLED(MULTI_VOLUME)
  1754. #define VOLUME_SD_ONBOARD
  1755. #define VOLUME_USB_FLASH_DRIVE
  1756. #define DEFAULT_VOLUME SV_SD_ONBOARD
  1757. #define DEFAULT_SHARED_VOLUME SV_USB_FLASH_DRIVE
  1758. #endif
  1759.  
  1760. #endif // SDSUPPORT
  1761.  
  1762. /**
  1763. * By default an onboard SD card reader may be shared as a USB mass-
  1764. * storage device. This option hides the SD card from the host PC.
  1765. */
  1766. //#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security).
  1767.  
  1768. /**
  1769. * Additional options for Graphical Displays
  1770. *
  1771. * Use the optimizations here to improve printing performance,
  1772. * which can be adversely affected by graphical display drawing,
  1773. * especially when doing several short moves, and when printing
  1774. * on DELTA and SCARA machines.
  1775. *
  1776. * Some of these options may result in the display lagging behind
  1777. * controller events, as there is a trade-off between reliable
  1778. * printing performance versus fast display updates.
  1779. */
  1780. #if HAS_MARLINUI_U8GLIB
  1781. // Show SD percentage next to the progress bar
  1782. #define DOGM_SD_PERCENT
  1783.  
  1784. // Save many cycles by drawing a hollow frame or no frame on the Info Screen
  1785. //#define XYZ_NO_FRAME
  1786. #define XYZ_HOLLOW_FRAME
  1787.  
  1788. // Enable to save many cycles by drawing a hollow frame on Menu Screens
  1789. #define MENU_HOLLOW_FRAME
  1790.  
  1791. // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
  1792. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  1793. //#define USE_BIG_EDIT_FONT
  1794.  
  1795. // A smaller font may be used on the Info Screen. Costs 2434 bytes of PROGMEM.
  1796. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  1797. //#define USE_SMALL_INFOFONT
  1798.  
  1799. // Swap the CW/CCW indicators in the graphics overlay
  1800. //#define OVERLAY_GFX_REVERSE
  1801.  
  1802.  
  1803.  
  1804.  
  1805.  
  1806.  
  1807.  
  1808.  
  1809.  
  1810. /**
  1811. * ST7920-based LCDs can emulate a 16 x 4 character display using
  1812. * the ST7920 character-generator for very fast screen updates.
  1813. * Enable LIGHTWEIGHT_UI to use this special display mode.
  1814. *
  1815. * Since LIGHTWEIGHT_UI has limited space, the position and status
  1816. * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the
  1817. * length of time to display the status message before clearing.
  1818. *
  1819. * Set STATUS_EXPIRE_SECONDS to zero to never clear the status.
  1820. * This will prevent position updates from being displayed.
  1821. */
  1822. #if ENABLED(U8GLIB_ST7920)
  1823. // Enable this option and reduce the value to optimize screen updates.
  1824. // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
  1825. //#define DOGM_SPI_DELAY_US 5
  1826.  
  1827. //#define LIGHTWEIGHT_UI
  1828. #if ENABLED(LIGHTWEIGHT_UI)
  1829. #define STATUS_EXPIRE_SECONDS 20
  1830. #endif
  1831. #endif
  1832.  
  1833. /**
  1834. * Status (Info) Screen customizations
  1835. * These options may affect code size and screen render time.
  1836. * Custom status screens can forcibly override these settings.
  1837. */
  1838. //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones
  1839. //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends)
  1840. #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM for numbered hotends)
  1841. #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating
  1842. #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating
  1843. #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating
  1844. //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active
  1845. //#define STATUS_COOLER_ANIM // Use a second bitmap to indicate laser cooling
  1846. //#define STATUS_FLOWMETER_ANIM // Use multiple bitmaps to indicate coolant flow
  1847. //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap
  1848. //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap
  1849. //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames
  1850. //#define STATUS_HEAT_PERCENT // Show heating in a progress bar
  1851. //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
  1852.  
  1853. // Frivolous Game Options
  1854. //#define MARLIN_BRICKOUT
  1855. //#define MARLIN_INVADERS
  1856. //#define MARLIN_SNAKE
  1857. //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu
  1858.  
  1859. #endif // HAS_MARLINUI_U8GLIB
  1860.  
  1861.  
  1862.  
  1863.  
  1864.  
  1865.  
  1866.  
  1867.  
  1868.  
  1869.  
  1870.  
  1871.  
  1872. //
  1873. // Additional options for DGUS / DWIN displays
  1874. //
  1875. #if HAS_DGUS_LCD
  1876. #define LCD_SERIAL_PORT 3
  1877. #define LCD_BAUDRATE 115200
  1878.  
  1879. #define DGUS_RX_BUFFER_SIZE 128
  1880. #define DGUS_TX_BUFFER_SIZE 48
  1881. //#define SERIAL_STATS_RX_BUFFER_OVERRUNS // Fix Rx overrun situation (Currently only for AVR)
  1882.  
  1883. #define DGUS_UPDATE_INTERVAL_MS 500 // (ms) Interval between automatic screen updates
  1884.  
  1885. #if ANY(DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_MKS, DGUS_LCD_UI_HIPRECY)
  1886. #define DGUS_PRINT_FILENAME // Display the filename during printing
  1887. #define DGUS_PREHEAT_UI // Display a preheat screen during heatup
  1888.  
  1889. #if EITHER(DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_MKS)
  1890. //#define DGUS_UI_MOVE_DIS_OPTION // Disabled by default for FYSETC and MKS
  1891. #else
  1892. #define DGUS_UI_MOVE_DIS_OPTION // Enabled by default for UI_HIPRECY
  1893. #endif
  1894.  
  1895. #define DGUS_FILAMENT_LOADUNLOAD
  1896. #if ENABLED(DGUS_FILAMENT_LOADUNLOAD)
  1897. #define DGUS_FILAMENT_PURGE_LENGTH 10
  1898. #define DGUS_FILAMENT_LOAD_LENGTH_PER_TIME 0.5 // (mm) Adjust in proportion to DGUS_UPDATE_INTERVAL_MS
  1899. #endif
  1900.  
  1901. #define DGUS_UI_WAITING // Show a "waiting" screen between some screens
  1902. #if ENABLED(DGUS_UI_WAITING)
  1903. #define DGUS_UI_WAITING_STATUS 10
  1904. #define DGUS_UI_WAITING_STATUS_PERIOD 8 // Increase to slower waiting status looping
  1905. #endif
  1906. #endif
  1907. #endif // HAS_DGUS_LCD
  1908.  
  1909. //
  1910. // Additional options for AnyCubic Chiron TFT displays
  1911. //
  1912. #if ENABLED(ANYCUBIC_LCD_CHIRON)
  1913. // By default the type of panel is automatically detected.
  1914. // Enable one of these options if you know the panel type.
  1915. //#define CHIRON_TFT_STANDARD
  1916. //#define CHIRON_TFT_NEW
  1917.  
  1918. // Enable the longer Anycubic powerup startup tune
  1919. //#define AC_DEFAULT_STARTUP_TUNE
  1920.  
  1921. /**
  1922. * Display Folders
  1923. * By default the file browser lists all G-code files (including those in subfolders) in a flat list.
  1924. * Enable this option to display a hierarchical file browser.
  1925. *
  1926. * NOTES:
  1927. * - Without this option it helps to enable SDCARD_SORT_ALPHA so files are sorted before/after folders.
  1928. * - When used with the "new" panel, folder names will also have '.gcode' appended to their names.
  1929. * This hack is currently required to force the panel to show folders.
  1930. */
  1931. #define AC_SD_FOLDER_VIEW
  1932. #endif
  1933.  
  1934. //
  1935. // Specify additional languages for the UI. Default specified by LCD_LANGUAGE.
  1936. //
  1937. #if ANY(DOGLCD, TFT_COLOR_UI, TOUCH_UI_FTDI_EVE)
  1938. //#define LCD_LANGUAGE_2 fr
  1939. //#define LCD_LANGUAGE_3 de
  1940. //#define LCD_LANGUAGE_4 es
  1941. //#define LCD_LANGUAGE_5 it
  1942. #ifdef LCD_LANGUAGE_2
  1943. //#define LCD_LANGUAGE_AUTO_SAVE // Automatically save language to EEPROM on change
  1944. #endif
  1945. #endif
  1946.  
  1947. //
  1948. // Touch UI for the FTDI Embedded Video Engine (EVE)
  1949. //
  1950. #if ENABLED(TOUCH_UI_FTDI_EVE)
  1951. // Display board used
  1952. //#define LCD_FTDI_VM800B35A // FTDI 3.5" with FT800 (320x240)
  1953. //#define LCD_4DSYSTEMS_4DLCD_FT843 // 4D Systems 4.3" (480x272)
  1954. //#define LCD_HAOYU_FT800CB // Haoyu with 4.3" or 5" (480x272)
  1955. //#define LCD_HAOYU_FT810CB // Haoyu with 5" (800x480)
  1956. //#define LCD_ALEPHOBJECTS_CLCD_UI // Aleph Objects Color LCD UI
  1957. //#define LCD_FYSETC_TFT81050 // FYSETC with 5" (800x480)
  1958. //#define LCD_EVE3_50G // Matrix Orbital 5.0", 800x480, BT815
  1959. //#define LCD_EVE2_50G // Matrix Orbital 5.0", 800x480, FT813
  1960.  
  1961. // Correct the resolution if not using the stock TFT panel.
  1962. //#define TOUCH_UI_320x240
  1963. //#define TOUCH_UI_480x272
  1964. //#define TOUCH_UI_800x480
  1965.  
  1966. // Mappings for boards with a standard RepRapDiscount Display connector
  1967. //#define AO_EXP1_PINMAP // AlephObjects CLCD UI EXP1 mapping
  1968. //#define AO_EXP2_PINMAP // AlephObjects CLCD UI EXP2 mapping
  1969. //#define CR10_TFT_PINMAP // Rudolph Riedel's CR10 pin mapping
  1970. //#define S6_TFT_PINMAP // FYSETC S6 pin mapping
  1971. //#define F6_TFT_PINMAP // FYSETC F6 pin mapping
  1972.  
  1973. //#define OTHER_PIN_LAYOUT // Define pins manually below
  1974. #if ENABLED(OTHER_PIN_LAYOUT)
  1975. // Pins for CS and MOD_RESET (PD) must be chosen
  1976. #define CLCD_MOD_RESET 9
  1977. #define CLCD_SPI_CS 10
  1978.  
  1979. // If using software SPI, specify pins for SCLK, MOSI, MISO
  1980. //#define CLCD_USE_SOFT_SPI
  1981. #if ENABLED(CLCD_USE_SOFT_SPI)
  1982. #define CLCD_SOFT_SPI_MOSI 11
  1983. #define CLCD_SOFT_SPI_MISO 12
  1984. #define CLCD_SOFT_SPI_SCLK 13
  1985. #endif
  1986. #endif
  1987.  
  1988. // Display Orientation. An inverted (i.e. upside-down) display
  1989. // is supported on the FT800. The FT810 and beyond also support
  1990. // portrait and mirrored orientations.
  1991. //#define TOUCH_UI_INVERTED
  1992. //#define TOUCH_UI_PORTRAIT
  1993. //#define TOUCH_UI_MIRRORED
  1994.  
  1995. // UTF8 processing and rendering.
  1996. // Unsupported characters are shown as '?'.
  1997. //#define TOUCH_UI_USE_UTF8
  1998. #if ENABLED(TOUCH_UI_USE_UTF8)
  1999. // Western accents support. These accented characters use
  2000. // combined bitmaps and require relatively little storage.
  2001. #define TOUCH_UI_UTF8_WESTERN_CHARSET
  2002. #if ENABLED(TOUCH_UI_UTF8_WESTERN_CHARSET)
  2003. // Additional character groups. These characters require
  2004. // full bitmaps and take up considerable storage:
  2005. //#define TOUCH_UI_UTF8_SUPERSCRIPTS // ¹ ² ³
  2006. //#define TOUCH_UI_UTF8_COPYRIGHT // © ®
  2007. //#define TOUCH_UI_UTF8_GERMANIC // ß
  2008. //#define TOUCH_UI_UTF8_SCANDINAVIAN // Æ Ð Ø Þ æ ð ø þ
  2009. //#define TOUCH_UI_UTF8_PUNCTUATION // « » ¿ ¡
  2010. //#define TOUCH_UI_UTF8_CURRENCY // ¢ £ ¤ ¥
  2011. //#define TOUCH_UI_UTF8_ORDINALS // º ª
  2012. //#define TOUCH_UI_UTF8_MATHEMATICS // ± × ÷
  2013. //#define TOUCH_UI_UTF8_FRACTIONS // ¼ ½ ¾
  2014. //#define TOUCH_UI_UTF8_SYMBOLS // µ ¶ ¦ § ¬
  2015. #endif
  2016.  
  2017. // Cyrillic character set, costs about 27KiB of flash
  2018. //#define TOUCH_UI_UTF8_CYRILLIC_CHARSET
  2019. #endif
  2020.  
  2021. // Use a smaller font when labels don't fit buttons
  2022. #define TOUCH_UI_FIT_TEXT
  2023.  
  2024. // Use a numeric passcode for "Screen lock" keypad.
  2025. // (recommended for smaller displays)
  2026. //#define TOUCH_UI_PASSCODE
  2027.  
  2028. // Output extra debug info for Touch UI events
  2029. //#define TOUCH_UI_DEBUG
  2030.  
  2031. // Developer menu (accessed by touching "About Printer" copyright text)
  2032. //#define TOUCH_UI_DEVELOPER_MENU
  2033. #endif
  2034.  
  2035. //
  2036. // Classic UI Options
  2037. //
  2038. #if TFT_SCALED_DOGLCD
  2039. //#define TFT_MARLINUI_COLOR 0xFFFF // White
  2040. //#define TFT_MARLINBG_COLOR 0x0000 // Black
  2041. //#define TFT_DISABLED_COLOR 0x0003 // Almost black
  2042. //#define TFT_BTCANCEL_COLOR 0xF800 // Red
  2043. //#define TFT_BTARROWS_COLOR 0xDEE6 // 11011 110111 00110 Yellow
  2044. //#define TFT_BTOKMENU_COLOR 0x145F // 00010 100010 11111 Cyan
  2045. #endif
  2046.  
  2047. //
  2048. // ADC Button Debounce
  2049. //
  2050. #if HAS_ADC_BUTTONS
  2051. #define ADC_BUTTON_DEBOUNCE_DELAY 16 // Increase if buttons bounce or repeat too fast
  2052. #endif
  2053.  
  2054. // @section safety
  2055.  
  2056. /**
  2057. * The watchdog hardware timer will do a reset and disable all outputs
  2058. * if the firmware gets too overloaded to read the temperature sensors.
  2059. *
  2060. * If you find that watchdog reboot causes your AVR board to hang forever,
  2061. * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
  2062. * NOTE: This method is less reliable as it can only catch hangups while
  2063. * interrupts are enabled.
  2064. */
  2065. #define USE_WATCHDOG
  2066. #if ENABLED(USE_WATCHDOG)
  2067. //#define WATCHDOG_RESET_MANUAL
  2068. #endif
  2069.  
  2070. // @section lcd
  2071.  
  2072. /**
  2073. * Babystepping enables movement of the axes by tiny increments without changing
  2074. * the current position values. This feature is used primarily to adjust the Z
  2075. * axis in the first layer of a print in real-time.
  2076. *
  2077. * Warning: Does not respect endstops!
  2078. */
  2079. #define BABYSTEPPING
  2080. #if ENABLED(BABYSTEPPING)
  2081. //#define INTEGRATED_BABYSTEPPING // EXPERIMENTAL integration of babystepping into the Stepper ISR
  2082. //#define BABYSTEP_WITHOUT_HOMING
  2083. //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement).
  2084. //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
  2085. #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
  2086. //#define BABYSTEP_MILLIMETER_UNITS // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
  2087. #define BABYSTEP_MULTIPLICATOR_Z 1 // (steps or mm) Steps or millimeter distance for each Z babystep
  2088. #define BABYSTEP_MULTIPLICATOR_XY 1 // (steps or mm) Steps or millimeter distance for each XY babystep
  2089.  
  2090. #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
  2091. #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
  2092. #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
  2093. // Note: Extra time may be added to mitigate controller latency.
  2094. //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle.
  2095. #if ENABLED(MOVE_Z_WHEN_IDLE)
  2096. #define MOVE_Z_IDLE_MULTIPLICATOR 2 // Multiply 1mm by this factor for the move step size.
  2097. #endif
  2098. #endif
  2099.  
  2100. #define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
  2101.  
  2102. #define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
  2103. #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
  2104. //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
  2105. //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
  2106. #endif
  2107. #endif
  2108.  
  2109. // @section extruder
  2110.  
  2111. /**
  2112. * Linear Pressure Control v1.5
  2113. *
  2114. * Assumption: advance [steps] = k * (delta velocity [steps/s])
  2115. * K=0 means advance disabled.
  2116. *
  2117. * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions!
  2118. *
  2119. * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak.
  2120. * Larger K values will be needed for flexible filament and greater distances.
  2121. * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk)
  2122. * print acceleration will be reduced during the affected moves to keep within the limit.
  2123. *
  2124. * See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
  2125. */
  2126. #define LIN_ADVANCE
  2127. #if ENABLED(LIN_ADVANCE)
  2128. //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
  2129. #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed
  2130. //#define LA_DEBUG // If enabled, this will generate debug information output over USB.
  2131. #define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
  2132.  
  2133. #endif
  2134.  
  2135. // @section leveling
  2136.  
  2137. /**
  2138. * Points to probe for all 3-point Leveling procedures.
  2139. * Override if the automatically selected points are inadequate.
  2140. */
  2141. #if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
  2142. //#define PROBE_PT_1_X 15
  2143. //#define PROBE_PT_1_Y 180
  2144. //#define PROBE_PT_2_X 15
  2145. //#define PROBE_PT_2_Y 20
  2146. //#define PROBE_PT_3_X 170
  2147. //#define PROBE_PT_3_Y 20
  2148. #endif
  2149.  
  2150. /**
  2151. * Probing Margins
  2152. *
  2153. * Override PROBING_MARGIN for each side of the build plate
  2154. * Useful to get probe points to exact positions on targets or
  2155. * to allow leveling to avoid plate clamps on only specific
  2156. * sides of the bed. With NOZZLE_AS_PROBE negative values are
  2157. * allowed, to permit probing outside the bed.
  2158. *
  2159. * If you are replacing the prior *_PROBE_BED_POSITION options,
  2160. * LEFT and FRONT values in most cases will map directly over
  2161. * RIGHT and REAR would be the inverse such as
  2162. * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
  2163. *
  2164. * This will allow all positions to match at compilation, however
  2165. * should the probe position be modified with M851XY then the
  2166. * probe points will follow. This prevents any change from causing
  2167. * the probe to be unable to reach any points.
  2168. */
  2169. #if PROBE_SELECTED && !IS_KINEMATIC
  2170. //#define PROBING_MARGIN_LEFT PROBING_MARGIN
  2171. //#define PROBING_MARGIN_RIGHT PROBING_MARGIN
  2172. //#define PROBING_MARGIN_FRONT PROBING_MARGIN
  2173. #define PROBING_MARGIN_BACK 60
  2174. #endif
  2175.  
  2176. #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
  2177. // Override the mesh area if the automatic (max) area is too large
  2178. //#define MESH_MIN_X MESH_INSET
  2179. //#define MESH_MIN_Y MESH_INSET
  2180. //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
  2181. //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
  2182. #endif
  2183.  
  2184. #if BOTH(AUTO_BED_LEVELING_UBL, EEPROM_SETTINGS)
  2185. //#define OPTIMIZED_MESH_STORAGE // Store mesh with less precision to save EEPROM space
  2186. #endif
  2187.  
  2188. /**
  2189. * Repeatedly attempt G29 leveling until it succeeds.
  2190. * Stop after G29_MAX_RETRIES attempts.
  2191. */
  2192. //#define G29_RETRY_AND_RECOVER
  2193. #if ENABLED(G29_RETRY_AND_RECOVER)
  2194. #define G29_MAX_RETRIES 3
  2195. #define G29_HALT_ON_FAILURE
  2196. /**
  2197. * Specify the GCODE commands that will be executed when leveling succeeds,
  2198. * between attempts, and after the maximum number of retries have been tried.
  2199. */
  2200. #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
  2201. #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
  2202. #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
  2203.  
  2204. #endif
  2205.  
  2206. /**
  2207. * Thermal Probe Compensation
  2208.  
  2209. * Probe measurements are adjusted to compensate for temperature distortion.
  2210.  
  2211. * Use G76 to calibrate this feature. Use M871 to set values manually.
  2212. * For a more detailed explanation of the process see G76_M871.cpp.
  2213.  
  2214.  
  2215. */
  2216. #if HAS_BED_PROBE && TEMP_SENSOR_PROBE && TEMP_SENSOR_BED
  2217. // Enable thermal first layer compensation using bed and probe temperatures
  2218. #define PROBE_TEMP_COMPENSATION
  2219.  
  2220. // Add additional compensation depending on hotend temperature
  2221. // Note: this values cannot be calibrated and have to be set manually
  2222. #if ENABLED(PROBE_TEMP_COMPENSATION)
  2223. // Park position to wait for probe cooldown
  2224. #define PTC_PARK_POS { 0, 0, 100 }
  2225.  
  2226. // Probe position to probe and wait for probe to reach target temperature
  2227. #define PTC_PROBE_POS { 90, 100 }
  2228.  
  2229. // Enable additional compensation using hotend temperature
  2230. // Note: this values cannot be calibrated automatically but have to be set manually
  2231. //#define USE_TEMP_EXT_COMPENSATION
  2232.  
  2233. // Probe temperature calibration generates a table of values starting at PTC_SAMPLE_START
  2234. // (e.g., 30), in steps of PTC_SAMPLE_RES (e.g., 5) with PTC_SAMPLE_COUNT (e.g., 10) samples.
  2235.  
  2236.  
  2237.  
  2238.  
  2239.  
  2240.  
  2241.  
  2242.  
  2243.  
  2244. //#define PTC_SAMPLE_START 30 // (°C)
  2245. //#define PTC_SAMPLE_RES 5 // (°C)
  2246. //#define PTC_SAMPLE_COUNT 10
  2247.  
  2248.  
  2249.  
  2250.  
  2251. // Bed temperature calibration builds a similar table.
  2252.  
  2253.  
  2254.  
  2255.  
  2256.  
  2257.  
  2258.  
  2259.  
  2260. //#define BTC_SAMPLE_START 60 // (°C)
  2261. //#define BTC_SAMPLE_RES 5 // (°C)
  2262. //#define BTC_SAMPLE_COUNT 10
  2263.  
  2264.  
  2265.  
  2266. // The temperature the probe should be at while taking measurements during bed temperature
  2267. // calibration.
  2268. //#define BTC_PROBE_TEMP 30 // (°C)
  2269.  
  2270.  
  2271. // Height above Z=0.0 to raise the nozzle. Lowering this can help the probe to heat faster.
  2272. // Note: the Z=0.0 offset is determined by the probe offset which can be set using M851.
  2273. //#define PTC_PROBE_HEATING_OFFSET 0.5
  2274.  
  2275. // Height to raise the Z-probe between heating and taking the next measurement. Some probes
  2276. // may fail to untrigger if they have been triggered for a long time, which can be solved by
  2277. // increasing the height the probe is raised to.
  2278. //#define PTC_PROBE_RAISE 15
  2279.  
  2280. // If the probe is outside of the defined range, use linear extrapolation using the closest
  2281. // point and the PTC_LINEAR_EXTRAPOLATION'th next point. E.g. if set to 4 it will use data[0]
  2282. // and data[4] to perform linear extrapolation for values below PTC_SAMPLE_START.
  2283. //#define PTC_LINEAR_EXTRAPOLATION 4
  2284. #endif
  2285. #endif
  2286.  
  2287. // @section extras
  2288.  
  2289. //
  2290. // G60/G61 Position Save and Return
  2291. //
  2292. //#define SAVED_POSITIONS 1 // Each saved position slot costs 12 bytes
  2293.  
  2294. //
  2295. // G2/G3 Arc Support
  2296. //
  2297. #define ARC_SUPPORT // Disable this feature to save ~3226 bytes
  2298. #if ENABLED(ARC_SUPPORT)
  2299. #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment
  2300. //#define ARC_SEGMENTS_PER_R 1 // Max segment length, MM_PER = Min
  2301. #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle
  2302. //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum)
  2303. #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections
  2304. //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles
  2305. //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes
  2306. //#define SF_ARC_FIX // Enable only if using SkeinForge with "Arc Point" fillet procedure
  2307. #endif
  2308.  
  2309. // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
  2310. //#define BEZIER_CURVE_SUPPORT
  2311.  
  2312.  
  2313.  
  2314.  
  2315.  
  2316. /**
  2317. * Direct Stepping
  2318. *
  2319. * Comparable to the method used by Klipper, G6 direct stepping significantly
  2320. * reduces motion calculations, increases top printing speeds, and results in
  2321. * less step aliasing by calculating all motions in advance.
  2322. * Preparing your G-code: https://github.com/colinrgodsey/step-daemon
  2323. */
  2324. //#define DIRECT_STEPPING
  2325.  
  2326. /**
  2327. * G38 Probe Target
  2328. *
  2329. * This option adds G38.2 and G38.3 (probe towards target)
  2330. * and optionally G38.4 and G38.5 (probe away from target).
  2331. * Set MULTIPLE_PROBING for G38 to probe more than once.
  2332. */
  2333. //#define G38_PROBE_TARGET
  2334. #if ENABLED(G38_PROBE_TARGET)
  2335. //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target
  2336. #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move.
  2337. #endif
  2338.  
  2339. // Moves (or segments) with fewer steps than this will be joined with the next move
  2340. #define MIN_STEPS_PER_SEGMENT 6
  2341.  
  2342. /**
  2343. * Minimum delay before and after setting the stepper DIR (in ns)
  2344. * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
  2345. * 20 : Minimum for TMC2xxx drivers
  2346. * 200 : Minimum for A4988 drivers
  2347. * 400 : Minimum for A5984 drivers
  2348. * 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
  2349. * 650 : Minimum for DRV8825 drivers
  2350. * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
  2351. * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
  2352. *
  2353. * Override the default value based on the driver type set in Configuration.h.
  2354. */
  2355. //#define MINIMUM_STEPPER_POST_DIR_DELAY 650
  2356. //#define MINIMUM_STEPPER_PRE_DIR_DELAY 650
  2357.  
  2358. /**
  2359. * Minimum stepper driver pulse width (in µs)
  2360. * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
  2361. * 0 : Minimum 500ns for LV8729, adjusted in stepper.h
  2362. * 1 : Minimum for A4988 and A5984 stepper drivers
  2363. * 2 : Minimum for DRV8825 stepper drivers
  2364. * 3 : Minimum for TB6600 stepper drivers
  2365. * 30 : Minimum for TB6560 stepper drivers
  2366. *
  2367. * Override the default value based on the driver type set in Configuration.h.
  2368. */
  2369. //#define MINIMUM_STEPPER_PULSE 30
  2370.  
  2371. /**
  2372. * Maximum stepping rate (in Hz) the stepper driver allows
  2373. * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
  2374. * 5000000 : Maximum for TMC2xxx stepper drivers
  2375. * 1000000 : Maximum for LV8729 stepper driver
  2376. * 500000 : Maximum for A4988 stepper driver
  2377. * 250000 : Maximum for DRV8825 stepper driver
  2378. * 150000 : Maximum for TB6600 stepper driver
  2379. * 15000 : Maximum for TB6560 stepper driver
  2380. *
  2381. * Override the default value based on the driver type set in Configuration.h.
  2382. */
  2383. //#define MAXIMUM_STEPPER_RATE 15000
  2384.  
  2385. // @section temperature
  2386.  
  2387. // Control heater 0 and heater 1 in parallel.
  2388. //#define HEATERS_PARALLEL
  2389.  
  2390. //===========================================================================
  2391. //================================= Buffers =================================
  2392. //===========================================================================
  2393.  
  2394. // @section motion
  2395.  
  2396. // The number of linear moves that can be in the planner at once.
  2397. // The value of BLOCK_BUFFER_SIZE must be a power of 2 (e.g., 8, 16, 32)
  2398. #if BOTH(SDSUPPORT, DIRECT_STEPPING)
  2399. #define BLOCK_BUFFER_SIZE 8
  2400. #elif ENABLED(SDSUPPORT)
  2401. #define BLOCK_BUFFER_SIZE 32
  2402. #else
  2403. #define BLOCK_BUFFER_SIZE 16
  2404. #endif
  2405.  
  2406. // @section serial
  2407.  
  2408. // The ASCII buffer for serial input
  2409. #define MAX_CMD_SIZE 96
  2410. #define BUFSIZE 32
  2411.  
  2412. // Transmission to Host Buffer Size
  2413. // To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
  2414. // To buffer a simple "ok" you need 4 bytes.
  2415. // For ADVANCED_OK (M105) you need 32 bytes.
  2416. // For debug-echo: 128 bytes for the optimal speed.
  2417. // Other output doesn't need to be that speedy.
  2418. // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
  2419. #define TX_BUFFER_SIZE 32
  2420.  
  2421. // Host Receive Buffer Size
  2422. // Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
  2423. // To use flow control, set this buffer size to at least 1024 bytes.
  2424. // :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
  2425. //#define RX_BUFFER_SIZE 1024
  2426.  
  2427. #if RX_BUFFER_SIZE >= 1024
  2428. // Enable to have the controller send XON/XOFF control characters to
  2429. // the host to signal the RX buffer is becoming full.
  2430. //#define SERIAL_XON_XOFF
  2431. #endif
  2432.  
  2433. #if ENABLED(SDSUPPORT)
  2434. // Enable this option to collect and display the maximum
  2435. // RX queue usage after transferring a file to SD.
  2436. //#define SERIAL_STATS_MAX_RX_QUEUED
  2437.  
  2438. // Enable this option to collect and display the number
  2439. // of dropped bytes after a file transfer to SD.
  2440. //#define SERIAL_STATS_DROPPED_RX
  2441. #endif
  2442.  
  2443. // Monitor RX buffer usage
  2444. // Dump an error to the serial port if the serial receive buffer overflows.
  2445. // If you see these errors, increase the RX_BUFFER_SIZE value.
  2446. // Not supported on all platforms.
  2447. //#define RX_BUFFER_MONITOR
  2448.  
  2449. /**
  2450. * Emergency Command Parser
  2451. *
  2452. * Add a low-level parser to intercept certain commands as they
  2453. * enter the serial receive buffer, so they cannot be blocked.
  2454. * Currently handles M108, M112, M410, M876
  2455. * NOTE: Not yet implemented for all platforms.
  2456. */
  2457. #define EMERGENCY_PARSER
  2458.  
  2459. /**
  2460. * Realtime Reporting (requires EMERGENCY_PARSER)
  2461. *
  2462. * - Report position and state of the machine (like Grbl).
  2463. * - Auto-report position during long moves.
  2464. * - Useful for CNC/LASER.
  2465. *
  2466. * Adds support for commands:
  2467. * S000 : Report State and Position while moving.
  2468. * P000 : Instant Pause / Hold while moving.
  2469. * R000 : Resume from Pause / Hold.
  2470. *
  2471. * - During Hold all Emergency Parser commands are available, as usual.
  2472. * - Enable NANODLP_Z_SYNC and NANODLP_ALL_AXIS for move command end-state reports.
  2473. */
  2474. //#define REALTIME_REPORTING_COMMANDS
  2475. #if ENABLED(REALTIME_REPORTING_COMMANDS)
  2476. //#define FULL_REPORT_TO_HOST_FEATURE // Auto-report the machine status like Grbl CNC
  2477. #endif
  2478.  
  2479. // Bad Serial-connections can miss a received command by sending an 'ok'
  2480. // Therefore some clients abort after 30 seconds in a timeout.
  2481. // Some other clients start sending commands while receiving a 'wait'.
  2482. // This "wait" is only sent when the buffer is empty. 1 second is a good value here.
  2483. //#define NO_TIMEOUTS 1000 // Milliseconds
  2484.  
  2485. // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
  2486. //#define ADVANCED_OK
  2487.  
  2488. // Printrun may have trouble receiving long strings all at once.
  2489. // This option inserts short delays between lines of serial output.
  2490. #define SERIAL_OVERRUN_PROTECTION
  2491.  
  2492. // For serial echo, the number of digits after the decimal point
  2493. //#define SERIAL_FLOAT_PRECISION 4
  2494.  
  2495.  
  2496.  
  2497.  
  2498.  
  2499.  
  2500.  
  2501.  
  2502.  
  2503.  
  2504. // @section extras
  2505.  
  2506. /**
  2507. * Extra Fan Speed
  2508. * Adds a secondary fan speed for each print-cooling fan.
  2509. * 'M106 P<fan> T3-255' : Set a secondary speed for <fan>
  2510. * 'M106 P<fan> T2' : Use the set secondary speed
  2511. * 'M106 P<fan> T1' : Restore the previous fan speed
  2512. */
  2513. //#define EXTRA_FAN_SPEED
  2514.  
  2515. /**
  2516. * Firmware-based and LCD-controlled retract
  2517. *
  2518. * Add G10 / G11 commands for automatic firmware-based retract / recover.
  2519. * Use M207 and M208 to define parameters for retract / recover.
  2520. *
  2521. * Use M209 to enable or disable auto-retract.
  2522. * With auto-retract enabled, all G1 E moves within the set range
  2523. * will be converted to firmware-based retract/recover moves.
  2524. *
  2525. * Be sure to turn off auto-retract during filament change.
  2526. *
  2527. * Note that M207 / M208 / M209 settings are saved to EEPROM.
  2528. */
  2529. //#define FWRETRACT
  2530. #if ENABLED(FWRETRACT)
  2531. #define FWRETRACT_AUTORETRACT // Override slicer retractions
  2532. #if ENABLED(FWRETRACT_AUTORETRACT)
  2533. #define MIN_AUTORETRACT 0.1 // (mm) Don't convert E moves under this length
  2534. #define MAX_AUTORETRACT 10.0 // (mm) Don't convert E moves over this length
  2535. #endif
  2536. #define RETRACT_LENGTH 3 // (mm) Default retract length (positive value)
  2537. #define RETRACT_LENGTH_SWAP 13 // (mm) Default swap retract length (positive value)
  2538. #define RETRACT_FEEDRATE 45 // (mm/s) Default feedrate for retracting
  2539. #define RETRACT_ZRAISE 0 // (mm) Default retract Z-raise
  2540. #define RETRACT_RECOVER_LENGTH 0 // (mm) Default additional recover length (added to retract length on recover)
  2541. #define RETRACT_RECOVER_LENGTH_SWAP 0 // (mm) Default additional swap recover length (added to retract length on recover from toolchange)
  2542. #define RETRACT_RECOVER_FEEDRATE 8 // (mm/s) Default feedrate for recovering from retraction
  2543. #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // (mm/s) Default feedrate for recovering from swap retraction
  2544. #if ENABLED(MIXING_EXTRUDER)
  2545. //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously
  2546. #endif
  2547. #endif
  2548.  
  2549. /**
  2550. * Universal tool change settings.
  2551. * Applies to all types of extruders except where explicitly noted.
  2552. */
  2553. #if HAS_MULTI_EXTRUDER
  2554. // Z raise distance for tool-change, as needed for some extruders
  2555. #define TOOLCHANGE_ZRAISE 2 // (mm)
  2556. //#define TOOLCHANGE_ZRAISE_BEFORE_RETRACT // Apply raise before swap retraction (if enabled)
  2557. //#define TOOLCHANGE_NO_RETURN // Never return to previous position on tool-change
  2558. #if ENABLED(TOOLCHANGE_NO_RETURN)
  2559. //#define EVENT_GCODE_AFTER_TOOLCHANGE "G12X" // Extra G-code to run after tool-change
  2560. #endif
  2561.  
  2562. /**
  2563. * Extra G-code to run while executing tool-change commands. Can be used to use an additional
  2564. * stepper motor (I axis, see option LINEAR_AXES in Configuration.h) to drive the tool-changer.
  2565. */
  2566. //#define EVENT_GCODE_TOOLCHANGE_T0 "G28 A\nG1 A0" // Extra G-code to run while executing tool-change command T0
  2567. //#define EVENT_GCODE_TOOLCHANGE_T1 "G1 A10" // Extra G-code to run while executing tool-change command T1
  2568.  
  2569.  
  2570. /**
  2571. * Tool Sensors detect when tools have been picked up or dropped.
  2572. * Requires the pins TOOL_SENSOR1_PIN, TOOL_SENSOR2_PIN, etc.
  2573. */
  2574. //#define TOOL_SENSOR
  2575.  
  2576. /**
  2577. * Retract and prime filament on tool-change to reduce
  2578. * ooze and stringing and to get cleaner transitions.
  2579. */
  2580. //#define TOOLCHANGE_FILAMENT_SWAP
  2581. #if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
  2582. // Load / Unload
  2583. #define TOOLCHANGE_FS_LENGTH 12 // (mm) Load / Unload length
  2584. #define TOOLCHANGE_FS_EXTRA_RESUME_LENGTH 0 // (mm) Extra length for better restart, fine tune by LCD/Gcode)
  2585. #define TOOLCHANGE_FS_RETRACT_SPEED (50*60) // (mm/min) (Unloading)
  2586. #define TOOLCHANGE_FS_UNRETRACT_SPEED (25*60) // (mm/min) (On SINGLENOZZLE or Bowden loading must be slowed down)
  2587.  
  2588. // Longer prime to clean out a SINGLENOZZLE
  2589. #define TOOLCHANGE_FS_EXTRA_PRIME 0 // (mm) Extra priming length
  2590. #define TOOLCHANGE_FS_PRIME_SPEED (4.6*60) // (mm/min) Extra priming feedrate
  2591. #define TOOLCHANGE_FS_WIPE_RETRACT 0 // (mm/min) Retract before cooling for less stringing, better wipe, etc.
  2592.  
  2593. // Cool after prime to reduce stringing
  2594. #define TOOLCHANGE_FS_FAN -1 // Fan index or -1 to skip
  2595. #define TOOLCHANGE_FS_FAN_SPEED 255 // 0-255
  2596. #define TOOLCHANGE_FS_FAN_TIME 10 // (seconds)
  2597.  
  2598. // Swap uninitialized extruder with TOOLCHANGE_FS_PRIME_SPEED for all lengths (recover + prime)
  2599. // (May break filament if not retracted beforehand.)
  2600. //#define TOOLCHANGE_FS_INIT_BEFORE_SWAP
  2601.  
  2602. // Prime on the first T0 (If other, TOOLCHANGE_FS_INIT_BEFORE_SWAP applied)
  2603.  
  2604.  
  2605.  
  2606.  
  2607. // Enable it (M217 V[0/1]) before printing, to avoid unwanted priming on host connect
  2608.  
  2609. //#define TOOLCHANGE_FS_PRIME_FIRST_USED
  2610.  
  2611. /**
  2612. * Tool Change Migration
  2613. * This feature provides G-code and LCD options to switch tools mid-print.
  2614. * All applicable tool properties are migrated so the print can continue.
  2615. * Tools must be closely matching and other restrictions may apply.
  2616. * Useful to:
  2617. * - Change filament color without interruption
  2618. * - Switch spools automatically on filament runout
  2619. * - Switch to a different nozzle on an extruder jam
  2620. */
  2621. #define TOOLCHANGE_MIGRATION_FEATURE
  2622.  
  2623. #endif
  2624.  
  2625. /**
  2626. * Position to park head during tool change.
  2627. * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER
  2628. */
  2629. //#define TOOLCHANGE_PARK
  2630. #if ENABLED(TOOLCHANGE_PARK)
  2631. #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 }
  2632. #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/min)
  2633. //#define TOOLCHANGE_PARK_X_ONLY // X axis only move
  2634. //#define TOOLCHANGE_PARK_Y_ONLY // Y axis only move
  2635. #endif
  2636. #endif // HAS_MULTI_EXTRUDER
  2637.  
  2638. /**
  2639. * Advanced Pause for Filament Change
  2640. * - Adds the G-code M600 Filament Change to initiate a filament change.
  2641. * - This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  2642. *
  2643. * Requirements:
  2644. * - For Filament Change parking enable and configure NOZZLE_PARK_FEATURE.
  2645. * - For user interaction enable an LCD display, HOST_PROMPT_SUPPORT, or EMERGENCY_PARSER.
  2646. *
  2647. * Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
  2648. */
  2649. #define ADVANCED_PAUSE_FEATURE
  2650. #if ENABLED(ADVANCED_PAUSE_FEATURE)
  2651. #define PAUSE_PARK_RETRACT_FEEDRATE 30 // (mm/s) Initial retract feedrate.
  2652. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
  2653. // This short retract is done immediately, before parking the nozzle.
  2654. #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 30 // (mm/s) Unload filament feedrate. This can be pretty fast.
  2655. #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
  2656. #define FILAMENT_CHANGE_UNLOAD_LENGTH 450 // (mm) The length of filament for a complete unload.
  2657. // For Bowden, the full length of the tube and nozzle.
  2658. // For direct drive, the full length of the nozzle.
  2659. // Set to 0 for manual unloading.
  2660. #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
  2661. #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 25 // (mm) Slow length, to allow time to insert material.
  2662. // 0 to disable start loading and skip to fast load only
  2663. #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 25 // (mm/s) Load filament feedrate. This can be pretty fast.
  2664. #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
  2665. #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 350 // (mm) Load length of filament, from extruder gear to nozzle.
  2666. // For Bowden, the full length of the tube and nozzle.
  2667. // For direct drive, the full length of the nozzle.
  2668. //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
  2669. #define ADVANCED_PAUSE_PURGE_FEEDRATE 5 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
  2670. #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
  2671. // Set to 0 for manual extrusion.
  2672. // Filament can be extruded repeatedly from the Filament Change menu
  2673. // until extrusion is consistent, and to purge old filament.
  2674. #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park.
  2675. //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused.
  2676.  
  2677. // Filament Unload does a Retract, Delay, and Purge first:
  2678. #define FILAMENT_UNLOAD_PURGE_RETRACT 13 // (mm) Unload initial retract length.
  2679. #define FILAMENT_UNLOAD_PURGE_DELAY 5000 // (ms) Delay for the filament to cool after retract.
  2680. #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
  2681. #define FILAMENT_UNLOAD_PURGE_FEEDRATE 25 // (mm/s) feedrate to purge before unload
  2682.  
  2683. #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
  2684. #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
  2685. #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
  2686.  
  2687.  
  2688.  
  2689. #define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
  2690. #define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
  2691.  
  2692. #define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
  2693. //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
  2694. #endif
  2695.  
  2696. // @section tmc
  2697.  
  2698. /**
  2699. * TMC26X Stepper Driver options
  2700. *
  2701. * The TMC26XStepper library is required for this stepper driver.
  2702. * https://github.com/trinamic/TMC26XStepper
  2703. */
  2704. #if HAS_DRIVER(TMC26X)
  2705.  
  2706. #if AXIS_DRIVER_TYPE_X(TMC26X)
  2707. #define X_MAX_CURRENT 1000 // (mA)
  2708. #define X_SENSE_RESISTOR 91 // (mOhms)
  2709. #define X_MICROSTEPS 16 // Number of microsteps
  2710. #endif
  2711.  
  2712. #if AXIS_DRIVER_TYPE_X2(TMC26X)
  2713. #define X2_MAX_CURRENT 1000
  2714. #define X2_SENSE_RESISTOR 91
  2715. #define X2_MICROSTEPS X_MICROSTEPS
  2716. #endif
  2717.  
  2718. #if AXIS_DRIVER_TYPE_Y(TMC26X)
  2719. #define Y_MAX_CURRENT 1000
  2720. #define Y_SENSE_RESISTOR 91
  2721. #define Y_MICROSTEPS 16
  2722. #endif
  2723.  
  2724. #if AXIS_DRIVER_TYPE_Y2(TMC26X)
  2725. #define Y2_MAX_CURRENT 1000
  2726. #define Y2_SENSE_RESISTOR 91
  2727. #define Y2_MICROSTEPS Y_MICROSTEPS
  2728. #endif
  2729.  
  2730. #if AXIS_DRIVER_TYPE_Z(TMC26X)
  2731. #define Z_MAX_CURRENT 1000
  2732. #define Z_SENSE_RESISTOR 91
  2733. #define Z_MICROSTEPS 16
  2734. #endif
  2735.  
  2736. #if AXIS_DRIVER_TYPE_Z2(TMC26X)
  2737. #define Z2_MAX_CURRENT 1000
  2738. #define Z2_SENSE_RESISTOR 91
  2739. #define Z2_MICROSTEPS Z_MICROSTEPS
  2740. #endif
  2741.  
  2742. #if AXIS_DRIVER_TYPE_Z3(TMC26X)
  2743. #define Z3_MAX_CURRENT 1000
  2744. #define Z3_SENSE_RESISTOR 91
  2745. #define Z3_MICROSTEPS Z_MICROSTEPS
  2746. #endif
  2747.  
  2748. #if AXIS_DRIVER_TYPE_Z4(TMC26X)
  2749. #define Z4_MAX_CURRENT 1000
  2750. #define Z4_SENSE_RESISTOR 91
  2751. #define Z4_MICROSTEPS Z_MICROSTEPS
  2752. #endif
  2753.  
  2754. #if AXIS_DRIVER_TYPE_I(TMC26X)
  2755. #define I_MAX_CURRENT 1000
  2756. #define I_SENSE_RESISTOR 91
  2757. #define I_MICROSTEPS 16
  2758. #endif
  2759.  
  2760. #if AXIS_DRIVER_TYPE_J(TMC26X)
  2761. #define J_MAX_CURRENT 1000
  2762. #define J_SENSE_RESISTOR 91
  2763. #define J_MICROSTEPS 16
  2764. #endif
  2765.  
  2766. #if AXIS_DRIVER_TYPE_K(TMC26X)
  2767. #define K_MAX_CURRENT 1000
  2768. #define K_SENSE_RESISTOR 91
  2769. #define K_MICROSTEPS 16
  2770. #endif
  2771.  
  2772. #if AXIS_DRIVER_TYPE_E0(TMC26X)
  2773. #define E0_MAX_CURRENT 1000
  2774. #define E0_SENSE_RESISTOR 91
  2775. #define E0_MICROSTEPS 16
  2776. #endif
  2777.  
  2778. #if AXIS_DRIVER_TYPE_E1(TMC26X)
  2779. #define E1_MAX_CURRENT 1000
  2780. #define E1_SENSE_RESISTOR 91
  2781. #define E1_MICROSTEPS E0_MICROSTEPS
  2782. #endif
  2783.  
  2784. #if AXIS_DRIVER_TYPE_E2(TMC26X)
  2785. #define E2_MAX_CURRENT 1000
  2786. #define E2_SENSE_RESISTOR 91
  2787. #define E2_MICROSTEPS E0_MICROSTEPS
  2788. #endif
  2789.  
  2790. #if AXIS_DRIVER_TYPE_E3(TMC26X)
  2791. #define E3_MAX_CURRENT 1000
  2792. #define E3_SENSE_RESISTOR 91
  2793. #define E3_MICROSTEPS E0_MICROSTEPS
  2794. #endif
  2795.  
  2796. #if AXIS_DRIVER_TYPE_E4(TMC26X)
  2797. #define E4_MAX_CURRENT 1000
  2798. #define E4_SENSE_RESISTOR 91
  2799. #define E4_MICROSTEPS E0_MICROSTEPS
  2800. #endif
  2801.  
  2802. #if AXIS_DRIVER_TYPE_E5(TMC26X)
  2803. #define E5_MAX_CURRENT 1000
  2804. #define E5_SENSE_RESISTOR 91
  2805. #define E5_MICROSTEPS E0_MICROSTEPS
  2806. #endif
  2807.  
  2808. #if AXIS_DRIVER_TYPE_E6(TMC26X)
  2809. #define E6_MAX_CURRENT 1000
  2810. #define E6_SENSE_RESISTOR 91
  2811. #define E6_MICROSTEPS E0_MICROSTEPS
  2812. #endif
  2813.  
  2814. #if AXIS_DRIVER_TYPE_E7(TMC26X)
  2815. #define E7_MAX_CURRENT 1000
  2816. #define E7_SENSE_RESISTOR 91
  2817. #define E7_MICROSTEPS E0_MICROSTEPS
  2818. #endif
  2819.  
  2820. #endif // TMC26X
  2821.  
  2822. // @section tmc_smart
  2823.  
  2824. /**
  2825. * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode
  2826. * connect your SPI pins to the hardware SPI interface on your board and define
  2827. * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3
  2828. * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
  2829. * You may also use software SPI if you wish to use general purpose IO pins.
  2830. *
  2831. * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN
  2832. * to the driver side PDN_UART pin with a 1K resistor.
  2833. * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without
  2834. * a resistor.
  2835. * The drivers can also be used with hardware serial.
  2836. *
  2837. * TMCStepper library is required to use TMC stepper drivers.
  2838. * https://github.com/teemuatlut/TMCStepper
  2839. */
  2840. #if HAS_TRINAMIC_CONFIG
  2841.  
  2842. #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
  2843.  
  2844. /**
  2845. * Interpolate microsteps to 256
  2846. * Override for each driver with <driver>_INTERPOLATE settings below
  2847. */
  2848. #define INTERPOLATE true
  2849.  
  2850. #if AXIS_IS_TMC(X)
  2851. #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current.
  2852. #define X_CURRENT_HOME X_CURRENT // (mA) RMS current for sensorless homing
  2853. #define X_MICROSTEPS 16 // 0..256
  2854. #define X_RSENSE 0.11
  2855. #define X_CHAIN_POS -1 // -1..0: Not chained. 1: MCU MOSI connected. 2: Next in chain, ...
  2856. #define X_INTERPOLATE true // Enable to override 'INTERPOLATE' for the X axis
  2857.  
  2858. #endif
  2859.  
  2860. #if AXIS_IS_TMC(X2)
  2861. #define X2_CURRENT 800
  2862. #define X2_CURRENT_HOME X2_CURRENT
  2863. #define X2_MICROSTEPS X_MICROSTEPS
  2864. #define X2_RSENSE 0.11
  2865. #define X2_CHAIN_POS -1
  2866. //#define X2_INTERPOLATE true
  2867.  
  2868. #endif
  2869.  
  2870. #if AXIS_IS_TMC(Y)
  2871. #define Y_CURRENT 800
  2872. #define Y_CURRENT_HOME Y_CURRENT
  2873. #define Y_MICROSTEPS 16
  2874. #define Y_RSENSE 0.11
  2875. #define Y_CHAIN_POS -1
  2876. #define Y_INTERPOLATE true
  2877.  
  2878. #endif
  2879.  
  2880. #if AXIS_IS_TMC(Y2)
  2881. #define Y2_CURRENT 800
  2882. #define Y2_CURRENT_HOME Y2_CURRENT
  2883. #define Y2_MICROSTEPS Y_MICROSTEPS
  2884. #define Y2_RSENSE 0.11
  2885. #define Y2_CHAIN_POS -1
  2886. //#define Y2_INTERPOLATE true
  2887.  
  2888. #endif
  2889.  
  2890. #if AXIS_IS_TMC(Z)
  2891. #define Z_CURRENT 800
  2892. #define Z_CURRENT_HOME Z_CURRENT
  2893. #define Z_MICROSTEPS 16
  2894. #define Z_RSENSE 0.11
  2895. #define Z_CHAIN_POS -1
  2896. #define Z_INTERPOLATE true
  2897.  
  2898. #endif
  2899.  
  2900. #if AXIS_IS_TMC(Z2)
  2901. #define Z2_CURRENT 800
  2902. #define Z2_CURRENT_HOME Z2_CURRENT
  2903. #define Z2_MICROSTEPS Z_MICROSTEPS
  2904. #define Z2_RSENSE 0.11
  2905. #define Z2_CHAIN_POS -1
  2906. //#define Z2_INTERPOLATE true
  2907.  
  2908. #endif
  2909.  
  2910. #if AXIS_IS_TMC(Z3)
  2911. #define Z3_CURRENT 800
  2912. #define Z3_CURRENT_HOME Z3_CURRENT
  2913. #define Z3_MICROSTEPS Z_MICROSTEPS
  2914. #define Z3_RSENSE 0.11
  2915. #define Z3_CHAIN_POS -1
  2916. //#define Z3_INTERPOLATE true
  2917.  
  2918. #endif
  2919.  
  2920. #if AXIS_IS_TMC(Z4)
  2921. #define Z4_CURRENT 800
  2922. #define Z4_CURRENT_HOME Z4_CURRENT
  2923. #define Z4_MICROSTEPS Z_MICROSTEPS
  2924. #define Z4_RSENSE 0.11
  2925. #define Z4_CHAIN_POS -1
  2926. //#define Z4_INTERPOLATE true
  2927.  
  2928. #endif
  2929.  
  2930. #if AXIS_IS_TMC(I)
  2931. #define I_CURRENT 800
  2932. #define I_CURRENT_HOME I_CURRENT
  2933. #define I_MICROSTEPS 16
  2934. #define I_RSENSE 0.11
  2935. #define I_CHAIN_POS -1
  2936. //#define I_INTERPOLATE true
  2937.  
  2938. #endif
  2939.  
  2940. #if AXIS_IS_TMC(J)
  2941. #define J_CURRENT 800
  2942. #define J_CURRENT_HOME J_CURRENT
  2943. #define J_MICROSTEPS 16
  2944. #define J_RSENSE 0.11
  2945. #define J_CHAIN_POS -1
  2946. //#define J_INTERPOLATE true
  2947.  
  2948. #endif
  2949.  
  2950. #if AXIS_IS_TMC(K)
  2951. #define K_CURRENT 800
  2952. #define K_CURRENT_HOME K_CURRENT
  2953. #define K_MICROSTEPS 16
  2954. #define K_RSENSE 0.11
  2955. #define K_CHAIN_POS -1
  2956. //#define K_INTERPOLATE true
  2957.  
  2958. #endif
  2959.  
  2960. #if AXIS_IS_TMC(E0)
  2961. #define E0_CURRENT 900
  2962. #define E0_MICROSTEPS 16
  2963. #define E0_RSENSE 0.11
  2964. #define E0_CHAIN_POS -1
  2965. #define E0_INTERPOLATE true
  2966.  
  2967. #endif
  2968.  
  2969. #if AXIS_IS_TMC(E1)
  2970. #define E1_CURRENT 900
  2971. #define E1_MICROSTEPS E0_MICROSTEPS
  2972. #define E1_RSENSE 0.11
  2973. #define E1_CHAIN_POS -1
  2974. #define E1_INTERPOLATE true
  2975.  
  2976. #endif
  2977.  
  2978. #if AXIS_IS_TMC(E2)
  2979. #define E2_CURRENT 800
  2980. #define E2_MICROSTEPS E0_MICROSTEPS
  2981. #define E2_RSENSE 0.11
  2982. #define E2_CHAIN_POS -1
  2983. //#define E2_INTERPOLATE true
  2984.  
  2985. #endif
  2986.  
  2987. #if AXIS_IS_TMC(E3)
  2988. #define E3_CURRENT 800
  2989. #define E3_MICROSTEPS E0_MICROSTEPS
  2990. #define E3_RSENSE 0.11
  2991. #define E3_CHAIN_POS -1
  2992. //#define E3_INTERPOLATE true
  2993.  
  2994. #endif
  2995.  
  2996. #if AXIS_IS_TMC(E4)
  2997. #define E4_CURRENT 800
  2998. #define E4_MICROSTEPS E0_MICROSTEPS
  2999. #define E4_RSENSE 0.11
  3000. #define E4_CHAIN_POS -1
  3001. //#define E4_INTERPOLATE true
  3002.  
  3003. #endif
  3004.  
  3005. #if AXIS_IS_TMC(E5)
  3006. #define E5_CURRENT 800
  3007. #define E5_MICROSTEPS E0_MICROSTEPS
  3008. #define E5_RSENSE 0.11
  3009. #define E5_CHAIN_POS -1
  3010. //#define E5_INTERPOLATE true
  3011.  
  3012. #endif
  3013.  
  3014. #if AXIS_IS_TMC(E6)
  3015. #define E6_CURRENT 800
  3016. #define E6_MICROSTEPS E0_MICROSTEPS
  3017. #define E6_RSENSE 0.11
  3018. #define E6_CHAIN_POS -1
  3019. //#define E6_INTERPOLATE true
  3020.  
  3021. #endif
  3022.  
  3023. #if AXIS_IS_TMC(E7)
  3024. #define E7_CURRENT 800
  3025. #define E7_MICROSTEPS E0_MICROSTEPS
  3026. #define E7_RSENSE 0.11
  3027. #define E7_CHAIN_POS -1
  3028. //#define E7_INTERPOLATE true
  3029.  
  3030. #endif
  3031.  
  3032. /**
  3033. * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here.
  3034. * The default pins can be found in your board's pins file.
  3035. */
  3036. //#define X_CS_PIN -1
  3037. //#define Y_CS_PIN -1
  3038. //#define Z_CS_PIN -1
  3039. //#define X2_CS_PIN -1
  3040. //#define Y2_CS_PIN -1
  3041. //#define Z2_CS_PIN -1
  3042. //#define Z3_CS_PIN -1
  3043. //#define Z4_CS_PIN -1
  3044. //#define I_CS_PIN -1
  3045. //#define J_CS_PIN -1
  3046. //#define K_CS_PIN -1
  3047. //#define E0_CS_PIN -1
  3048. //#define E1_CS_PIN -1
  3049. //#define E2_CS_PIN -1
  3050. //#define E3_CS_PIN -1
  3051. //#define E4_CS_PIN -1
  3052. //#define E5_CS_PIN -1
  3053. //#define E6_CS_PIN -1
  3054. //#define E7_CS_PIN -1
  3055.  
  3056. /**
  3057. * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160).
  3058. * The default SW SPI pins are defined the respective pins files,
  3059. * but you can override or define them here.
  3060. */
  3061. //#define TMC_USE_SW_SPI
  3062. //#define TMC_SW_MOSI -1
  3063. //#define TMC_SW_MISO -1
  3064. //#define TMC_SW_SCK -1
  3065.  
  3066. /**
  3067. * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses.
  3068. * Set the address using jumpers on pins MS1 and MS2.
  3069. * Address | MS1 | MS2
  3070. * 0 | LOW | LOW
  3071. * 1 | HIGH | LOW
  3072. * 2 | LOW | HIGH
  3073. * 3 | HIGH | HIGH
  3074. *
  3075. * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers
  3076. * on the same serial port, either here or in your board's pins file.
  3077. */
  3078. #define X_SLAVE_ADDRESS 0
  3079. #define Y_SLAVE_ADDRESS 0
  3080. #define Z_SLAVE_ADDRESS 0
  3081. #define X2_SLAVE_ADDRESS 0
  3082. #define Y2_SLAVE_ADDRESS 0
  3083. #define Z2_SLAVE_ADDRESS 0
  3084. #define Z3_SLAVE_ADDRESS 0
  3085. #define Z4_SLAVE_ADDRESS 0
  3086.  
  3087.  
  3088.  
  3089. #define E0_SLAVE_ADDRESS 0
  3090. #define E1_SLAVE_ADDRESS 0
  3091. #define E2_SLAVE_ADDRESS 0
  3092. #define E3_SLAVE_ADDRESS 0
  3093. #define E4_SLAVE_ADDRESS 0
  3094. #define E5_SLAVE_ADDRESS 0
  3095. #define E6_SLAVE_ADDRESS 0
  3096. #define E7_SLAVE_ADDRESS 0
  3097.  
  3098. /**
  3099. * Software enable
  3100. *
  3101. * Use for drivers that do not use a dedicated enable pin, but rather handle the same
  3102. * function through a communication line such as SPI or UART.
  3103. */
  3104. //#define SOFTWARE_DRIVER_ENABLE
  3105.  
  3106. /**
  3107. * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
  3108. * Use Trinamic's ultra quiet stepping mode.
  3109. * When disabled, Marlin will use spreadCycle stepping mode.
  3110. */
  3111. #define STEALTHCHOP_XY
  3112. #define STEALTHCHOP_Z
  3113. #define STEALTHCHOP_I
  3114. #define STEALTHCHOP_J
  3115. #define STEALTHCHOP_K
  3116. #define STEALTHCHOP_E
  3117.  
  3118. /**
  3119. * Optimize spreadCycle chopper parameters by using predefined parameter sets
  3120. * or with the help of an example included in the library.
  3121. * Provided parameter sets are
  3122. * CHOPPER_DEFAULT_12V
  3123. * CHOPPER_DEFAULT_19V
  3124. * CHOPPER_DEFAULT_24V
  3125. * CHOPPER_DEFAULT_36V
  3126. * CHOPPER_09STEP_24V // 0.9 degree steppers (24V)
  3127. * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Průša firmware for MK3 (24V)
  3128. * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9
  3129. *
  3130. * Define your own with:
  3131. * { <off_time[1..15]>, <hysteresis_end[-3..12]>, hysteresis_start[1..8] }
  3132. */
  3133. #define CHOPPER_TIMING CHOPPER_DEFAULT_24V // All axes (override below)
  3134. //#define CHOPPER_TIMING_X CHOPPER_TIMING // For X Axes (override below)
  3135. //#define CHOPPER_TIMING_X2 CHOPPER_TIMING_X
  3136. //#define CHOPPER_TIMING_Y CHOPPER_TIMING // For Y Axes (override below)
  3137. //#define CHOPPER_TIMING_Y2 CHOPPER_TIMING_Y
  3138. //#define CHOPPER_TIMING_Z CHOPPER_TIMING // For Z Axes (override below)
  3139. //#define CHOPPER_TIMING_Z2 CHOPPER_TIMING_Z
  3140. //#define CHOPPER_TIMING_Z3 CHOPPER_TIMING_Z
  3141. //#define CHOPPER_TIMING_Z4 CHOPPER_TIMING_Z
  3142.  
  3143.  
  3144.  
  3145. //#define CHOPPER_TIMING_E CHOPPER_TIMING // For Extruders (override below)
  3146. //#define CHOPPER_TIMING_E1 CHOPPER_TIMING_E
  3147. //#define CHOPPER_TIMING_E2 CHOPPER_TIMING_E
  3148. //#define CHOPPER_TIMING_E3 CHOPPER_TIMING_E
  3149. //#define CHOPPER_TIMING_E4 CHOPPER_TIMING_E
  3150. //#define CHOPPER_TIMING_E5 CHOPPER_TIMING_E
  3151. //#define CHOPPER_TIMING_E6 CHOPPER_TIMING_E
  3152. //#define CHOPPER_TIMING_E7 CHOPPER_TIMING_E
  3153.  
  3154. /**
  3155. * Monitor Trinamic drivers
  3156. * for error conditions like overtemperature and short to ground.
  3157. * To manage over-temp Marlin can decrease the driver current until the error condition clears.
  3158. * Other detected conditions can be used to stop the current print.
  3159. * Relevant G-codes:
  3160. * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given.
  3161. * M911 - Report stepper driver overtemperature pre-warn condition.
  3162. * M912 - Clear stepper driver overtemperature pre-warn condition flag.
  3163. * M122 - Report driver parameters (Requires TMC_DEBUG)
  3164. */
  3165. #define MONITOR_DRIVER_STATUS
  3166.  
  3167. #if ENABLED(MONITOR_DRIVER_STATUS)
  3168. #define CURRENT_STEP_DOWN 50 // [mA]
  3169. #define REPORT_CURRENT_CHANGE
  3170. #define STOP_ON_ERROR
  3171. #endif
  3172.  
  3173. /**
  3174. * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
  3175. * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
  3176. * This mode allows for faster movements at the expense of higher noise levels.
  3177. * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
  3178. * M913 X/Y/Z/E to live tune the setting
  3179. */
  3180. //#define HYBRID_THRESHOLD
  3181.  
  3182. #define X_HYBRID_THRESHOLD 100 // [mm/s]
  3183. #define X2_HYBRID_THRESHOLD 100
  3184. #define Y_HYBRID_THRESHOLD 100
  3185. #define Y2_HYBRID_THRESHOLD 100
  3186. #define Z_HYBRID_THRESHOLD 3
  3187. #define Z2_HYBRID_THRESHOLD 3
  3188. #define Z3_HYBRID_THRESHOLD 3
  3189. #define Z4_HYBRID_THRESHOLD 3
  3190. #define I_HYBRID_THRESHOLD 3
  3191. #define J_HYBRID_THRESHOLD 3
  3192. #define K_HYBRID_THRESHOLD 3
  3193. #define E0_HYBRID_THRESHOLD 30
  3194. #define E1_HYBRID_THRESHOLD 30
  3195. #define E2_HYBRID_THRESHOLD 30
  3196. #define E3_HYBRID_THRESHOLD 30
  3197. #define E4_HYBRID_THRESHOLD 30
  3198. #define E5_HYBRID_THRESHOLD 30
  3199. #define E6_HYBRID_THRESHOLD 30
  3200. #define E7_HYBRID_THRESHOLD 30
  3201.  
  3202. /**
  3203. * Use StallGuard to home / probe X, Y, Z.
  3204. *
  3205. * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only
  3206. * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
  3207. * X, Y, and Z homing will always be done in spreadCycle mode.
  3208. *
  3209. * X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
  3210. * Use M914 X Y Z to set the stall threshold at runtime:
  3211. *
  3212. * Sensitivity TMC2209 Others
  3213. * HIGHEST 255 -64 (Too sensitive => False positive)
  3214. * LOWEST 0 63 (Too insensitive => No trigger)
  3215. *
  3216. * It is recommended to set HOMING_BUMP_MM to { 0, 0, 0 }.
  3217. *
  3218. * SPI_ENDSTOPS *** Beta feature! *** TMC2130/TMC5160 Only ***
  3219. * Poll the driver through SPI to determine load when homing.
  3220. * Removes the need for a wire from DIAG1 to an endstop pin.
  3221. *
  3222. * IMPROVE_HOMING_RELIABILITY tunes acceleration and jerk when
  3223. * homing and adds a guard period for endstop triggering.
  3224. *
  3225. * Comment *_STALL_SENSITIVITY to disable sensorless homing for that axis.
  3226. */
  3227. //#define SENSORLESS_HOMING // StallGuard capable drivers only
  3228.  
  3229. #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING)
  3230. // TMC2209: 0...255. TMC2130: -64...63
  3231. #define X_STALL_SENSITIVITY 8
  3232. #define X2_STALL_SENSITIVITY X_STALL_SENSITIVITY
  3233. #define Y_STALL_SENSITIVITY 8
  3234. #define Y2_STALL_SENSITIVITY Y_STALL_SENSITIVITY
  3235. //#define Z_STALL_SENSITIVITY 8
  3236. //#define Z2_STALL_SENSITIVITY Z_STALL_SENSITIVITY
  3237. //#define Z3_STALL_SENSITIVITY Z_STALL_SENSITIVITY
  3238. //#define Z4_STALL_SENSITIVITY Z_STALL_SENSITIVITY
  3239. //#define I_STALL_SENSITIVITY 8
  3240. //#define J_STALL_SENSITIVITY 8
  3241. //#define K_STALL_SENSITIVITY 8
  3242. //#define SPI_ENDSTOPS // TMC2130 only
  3243. //#define IMPROVE_HOMING_RELIABILITY
  3244. #endif
  3245.  
  3246. /**
  3247. * TMC Homing stepper phase.
  3248. *
  3249. * Improve homing repeatability by homing to stepper coil's nearest absolute
  3250. * phase position. Trinamic drivers use a stepper phase table with 1024 values
  3251. * spanning 4 full steps with 256 positions each (ergo, 1024 positions).
  3252. * Full step positions (128, 384, 640, 896) have the highest holding torque.
  3253. *
  3254. * Values from 0..1023, -1 to disable homing phase for that axis.
  3255. */
  3256. //#define TMC_HOME_PHASE { 896, 896, 896 }
  3257.  
  3258. /**
  3259. * Beta feature!
  3260. * Create a 50/50 square wave step pulse optimal for stepper drivers.
  3261. */
  3262. //#define SQUARE_WAVE_STEPPING
  3263.  
  3264. /**
  3265. * Enable M122 debugging command for TMC stepper drivers.
  3266. * M122 S0/1 will enable continuous reporting.
  3267. */
  3268. #define TMC_DEBUG
  3269.  
  3270. /**
  3271. * You can set your own advanced settings by filling in predefined functions.
  3272. * A list of available functions can be found on the library github page
  3273. * https://github.com/teemuatlut/TMCStepper
  3274. *
  3275. * Example:
  3276. * #define TMC_ADV() { \
  3277. * stepperX.diag0_otpw(1); \
  3278. * stepperY.intpol(0); \
  3279. * }
  3280. */
  3281. #define TMC_ADV() { }
  3282.  
  3283. #endif // HAS_TRINAMIC_CONFIG
  3284.  
  3285. // @section L64XX
  3286.  
  3287. /**
  3288. * L64XX Stepper Driver options
  3289. *
  3290. * Arduino-L6470 library (0.8.0 or higher) is required.
  3291. * https://github.com/ameyer/Arduino-L6470
  3292. *
  3293. * Requires the following to be defined in your pins_YOUR_BOARD file
  3294. * L6470_CHAIN_SCK_PIN
  3295. * L6470_CHAIN_MISO_PIN
  3296. * L6470_CHAIN_MOSI_PIN
  3297. * L6470_CHAIN_SS_PIN
  3298. * ENABLE_RESET_L64XX_CHIPS(Q) where Q is 1 to enable and 0 to reset
  3299. */
  3300.  
  3301. #if HAS_L64XX
  3302.  
  3303. //#define L6470_CHITCHAT // Display additional status info
  3304.  
  3305. #if AXIS_IS_L64XX(X)
  3306. #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) - L6474 max is 16
  3307. #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current
  3308. // L6470 & L6474 - VALID: 375 x (1 - 16) - 6A max - rounds down
  3309. // POWERSTEP01: VALID: 1000 x (1 - 32) - 32A max - rounds down
  3310. #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down)
  3311. // L6470 & L6474 - VALID: 31.25 * (1-128) - 4A max - rounds down
  3312. // POWERSTEP01: VALID: 200 x (1 - 32) - 6.4A max - rounds down
  3313. // L6474 - STALLCURRENT setting is used to set the nominal (TVAL) current
  3314. #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper - not used by L6474
  3315. #define X_CHAIN_POS -1 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI
  3316. #define X_SLEW_RATE 1 // 0-3, Slew 0 is slowest, 3 is fastest
  3317. #endif
  3318.  
  3319. #if AXIS_IS_L64XX(X2)
  3320. #define X2_MICROSTEPS X_MICROSTEPS
  3321. #define X2_OVERCURRENT 2000
  3322. #define X2_STALLCURRENT 1500
  3323. #define X2_MAX_VOLTAGE 127
  3324. #define X2_CHAIN_POS -1
  3325. #define X2_SLEW_RATE 1
  3326. #endif
  3327.  
  3328. #if AXIS_IS_L64XX(Y)
  3329. #define Y_MICROSTEPS 128
  3330. #define Y_OVERCURRENT 2000
  3331. #define Y_STALLCURRENT 1500
  3332. #define Y_MAX_VOLTAGE 127
  3333. #define Y_CHAIN_POS -1
  3334. #define Y_SLEW_RATE 1
  3335. #endif
  3336.  
  3337. #if AXIS_IS_L64XX(Y2)
  3338. #define Y2_MICROSTEPS Y_MICROSTEPS
  3339. #define Y2_OVERCURRENT 2000
  3340. #define Y2_STALLCURRENT 1500
  3341. #define Y2_MAX_VOLTAGE 127
  3342. #define Y2_CHAIN_POS -1
  3343. #define Y2_SLEW_RATE 1
  3344. #endif
  3345.  
  3346. #if AXIS_IS_L64XX(Z)
  3347. #define Z_MICROSTEPS 128
  3348. #define Z_OVERCURRENT 2000
  3349. #define Z_STALLCURRENT 1500
  3350. #define Z_MAX_VOLTAGE 127
  3351. #define Z_CHAIN_POS -1
  3352. #define Z_SLEW_RATE 1
  3353. #endif
  3354.  
  3355. #if AXIS_IS_L64XX(Z2)
  3356. #define Z2_MICROSTEPS Z_MICROSTEPS
  3357. #define Z2_OVERCURRENT 2000
  3358. #define Z2_STALLCURRENT 1500
  3359. #define Z2_MAX_VOLTAGE 127
  3360. #define Z2_CHAIN_POS -1
  3361. #define Z2_SLEW_RATE 1
  3362. #endif
  3363.  
  3364. #if AXIS_IS_L64XX(Z3)
  3365. #define Z3_MICROSTEPS Z_MICROSTEPS
  3366. #define Z3_OVERCURRENT 2000
  3367. #define Z3_STALLCURRENT 1500
  3368. #define Z3_MAX_VOLTAGE 127
  3369. #define Z3_CHAIN_POS -1
  3370. #define Z3_SLEW_RATE 1
  3371. #endif
  3372.  
  3373. #if AXIS_IS_L64XX(Z4)
  3374. #define Z4_MICROSTEPS Z_MICROSTEPS
  3375. #define Z4_OVERCURRENT 2000
  3376. #define Z4_STALLCURRENT 1500
  3377. #define Z4_MAX_VOLTAGE 127
  3378. #define Z4_CHAIN_POS -1
  3379. #define Z4_SLEW_RATE 1
  3380. #endif
  3381.  
  3382. #if AXIS_DRIVER_TYPE_I(L6470)
  3383. #define I_MICROSTEPS 128
  3384. #define I_OVERCURRENT 2000
  3385. #define I_STALLCURRENT 1500
  3386. #define I_MAX_VOLTAGE 127
  3387. #define I_CHAIN_POS -1
  3388. #define I_SLEW_RATE 1
  3389. #endif
  3390.  
  3391. #if AXIS_DRIVER_TYPE_J(L6470)
  3392. #define J_MICROSTEPS 128
  3393. #define J_OVERCURRENT 2000
  3394. #define J_STALLCURRENT 1500
  3395. #define J_MAX_VOLTAGE 127
  3396. #define J_CHAIN_POS -1
  3397. #define J_SLEW_RATE 1
  3398. #endif
  3399.  
  3400. #if AXIS_DRIVER_TYPE_K(L6470)
  3401. #define K_MICROSTEPS 128
  3402. #define K_OVERCURRENT 2000
  3403. #define K_STALLCURRENT 1500
  3404. #define K_MAX_VOLTAGE 127
  3405. #define K_CHAIN_POS -1
  3406. #define K_SLEW_RATE 1
  3407. #endif
  3408.  
  3409. #if AXIS_IS_L64XX(E0)
  3410. #define E0_MICROSTEPS 128
  3411. #define E0_OVERCURRENT 2000
  3412. #define E0_STALLCURRENT 1500
  3413. #define E0_MAX_VOLTAGE 127
  3414. #define E0_CHAIN_POS -1
  3415. #define E0_SLEW_RATE 1
  3416. #endif
  3417.  
  3418. #if AXIS_IS_L64XX(E1)
  3419. #define E1_MICROSTEPS E0_MICROSTEPS
  3420. #define E1_OVERCURRENT 2000
  3421. #define E1_STALLCURRENT 1500
  3422. #define E1_MAX_VOLTAGE 127
  3423. #define E1_CHAIN_POS -1
  3424. #define E1_SLEW_RATE 1
  3425. #endif
  3426.  
  3427. #if AXIS_IS_L64XX(E2)
  3428. #define E2_MICROSTEPS E0_MICROSTEPS
  3429. #define E2_OVERCURRENT 2000
  3430. #define E2_STALLCURRENT 1500
  3431. #define E2_MAX_VOLTAGE 127
  3432. #define E2_CHAIN_POS -1
  3433. #define E2_SLEW_RATE 1
  3434. #endif
  3435.  
  3436. #if AXIS_IS_L64XX(E3)
  3437. #define E3_MICROSTEPS E0_MICROSTEPS
  3438. #define E3_OVERCURRENT 2000
  3439. #define E3_STALLCURRENT 1500
  3440. #define E3_MAX_VOLTAGE 127
  3441. #define E3_CHAIN_POS -1
  3442. #define E3_SLEW_RATE 1
  3443. #endif
  3444.  
  3445. #if AXIS_IS_L64XX(E4)
  3446. #define E4_MICROSTEPS E0_MICROSTEPS
  3447. #define E4_OVERCURRENT 2000
  3448. #define E4_STALLCURRENT 1500
  3449. #define E4_MAX_VOLTAGE 127
  3450. #define E4_CHAIN_POS -1
  3451. #define E4_SLEW_RATE 1
  3452. #endif
  3453.  
  3454. #if AXIS_IS_L64XX(E5)
  3455. #define E5_MICROSTEPS E0_MICROSTEPS
  3456. #define E5_OVERCURRENT 2000
  3457. #define E5_STALLCURRENT 1500
  3458. #define E5_MAX_VOLTAGE 127
  3459. #define E5_CHAIN_POS -1
  3460. #define E5_SLEW_RATE 1
  3461. #endif
  3462.  
  3463. #if AXIS_IS_L64XX(E6)
  3464. #define E6_MICROSTEPS E0_MICROSTEPS
  3465. #define E6_OVERCURRENT 2000
  3466. #define E6_STALLCURRENT 1500
  3467. #define E6_MAX_VOLTAGE 127
  3468. #define E6_CHAIN_POS -1
  3469. #define E6_SLEW_RATE 1
  3470. #endif
  3471.  
  3472. #if AXIS_IS_L64XX(E7)
  3473. #define E7_MICROSTEPS E0_MICROSTEPS
  3474. #define E7_OVERCURRENT 2000
  3475. #define E7_STALLCURRENT 1500
  3476. #define E7_MAX_VOLTAGE 127
  3477. #define E7_CHAIN_POS -1
  3478. #define E7_SLEW_RATE 1
  3479. #endif
  3480.  
  3481. /**
  3482. * Monitor L6470 drivers for error conditions like over temperature and over current.
  3483. * In the case of over temperature Marlin can decrease the drive until the error condition clears.
  3484. * Other detected conditions can be used to stop the current print.
  3485. * Relevant G-codes:
  3486. * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given.
  3487. * I not present or I0 or I1 - X, Y, Z or E0
  3488. * I2 - X2, Y2, Z2 or E1
  3489. * I3 - Z3 or E3
  3490. * I4 - Z4 or E4
  3491. * I5 - E5
  3492. * M916 - Increase drive level until get thermal warning
  3493. * M917 - Find minimum current thresholds
  3494. * M918 - Increase speed until max or error
  3495. * M122 S0/1 - Report driver parameters
  3496. */
  3497. //#define MONITOR_L6470_DRIVER_STATUS
  3498.  
  3499. #if ENABLED(MONITOR_L6470_DRIVER_STATUS)
  3500. #define KVAL_HOLD_STEP_DOWN 1
  3501. //#define L6470_STOP_ON_ERROR
  3502. #endif
  3503.  
  3504. #endif // HAS_L64XX
  3505.  
  3506. // @section i2cbus
  3507.  
  3508. //
  3509. // I2C Master ID for LPC176x LCD and Digital Current control
  3510. // Does not apply to other peripherals based on the Wire library.
  3511. //
  3512. //#define I2C_MASTER_ID 1 // Set a value from 0 to 2
  3513.  
  3514. /**
  3515. * TWI/I2C BUS
  3516. *
  3517. * This feature is an EXPERIMENTAL feature so it shall not be used on production
  3518. * machines. Enabling this will allow you to send and receive I2C data from slave
  3519. * devices on the bus.
  3520. *
  3521. * ; Example #1
  3522. * ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
  3523. * ; It uses multiple M260 commands with one B<base 10> arg
  3524. * M260 A99 ; Target slave address
  3525. * M260 B77 ; M
  3526. * M260 B97 ; a
  3527. * M260 B114 ; r
  3528. * M260 B108 ; l
  3529. * M260 B105 ; i
  3530. * M260 B110 ; n
  3531. * M260 S1 ; Send the current buffer
  3532. *
  3533. * ; Example #2
  3534. * ; Request 6 bytes from slave device with address 0x63 (99)
  3535. * M261 A99 B5
  3536. *
  3537. * ; Example #3
  3538. * ; Example serial output of a M261 request
  3539. * echo:i2c-reply: from:99 bytes:5 data:hello
  3540. */
  3541.  
  3542. //#define EXPERIMENTAL_I2CBUS
  3543. #if ENABLED(EXPERIMENTAL_I2CBUS)
  3544. #define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
  3545. #endif
  3546.  
  3547. // @section extras
  3548.  
  3549. /**
  3550. * Photo G-code
  3551. * Add the M240 G-code to take a photo.
  3552. * The photo can be triggered by a digital pin or a physical movement.
  3553. */
  3554. //#define PHOTO_GCODE
  3555. #if ENABLED(PHOTO_GCODE)
  3556. // A position to move to (and raise Z) before taking the photo
  3557. //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z)
  3558. //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P)
  3559. //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S)
  3560.  
  3561. // Canon RC-1 or homebrew digital camera trigger
  3562. // Data from: https://www.doc-diy.net/photo/rc-1_hacked/
  3563. //#define PHOTOGRAPH_PIN 23
  3564.  
  3565. // Canon Hack Development Kit
  3566. // https://captain-slow.dk/2014/03/09/3d-printing-timelapses/
  3567. //#define CHDK_PIN 4
  3568.  
  3569. // Optional second move with delay to trigger the camera shutter
  3570. //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J)
  3571.  
  3572. // Duration to hold the switch or keep CHDK_PIN high
  3573. //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D)
  3574.  
  3575. /**
  3576. * PHOTO_PULSES_US may need adjustment depending on board and camera model.
  3577. * Pin must be running at 48.4kHz.
  3578. * Be sure to use a PHOTOGRAPH_PIN which can rise and fall quick enough.
  3579. * (e.g., MKS SBase temp sensor pin was too slow, so used P1.23 on J8.)
  3580. *
  3581. * Example pulse data for Nikon: https://bit.ly/2FKD0Aq
  3582. * IR Wiring: https://git.io/JvJf7
  3583. */
  3584. //#define PHOTO_PULSES_US { 2000, 27850, 400, 1580, 400, 3580, 400 } // (µs) Durations for each 48.4kHz oscillation
  3585. #ifdef PHOTO_PULSES_US
  3586. #define PHOTO_PULSE_DELAY_US 13 // (µs) Approximate duration of each HIGH and LOW pulse in the oscillation
  3587. #endif
  3588. #endif
  3589.  
  3590. /**
  3591. * Spindle & Laser control
  3592. *
  3593. * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
  3594. * to set spindle speed, spindle direction, and laser power.
  3595. *
  3596. * SuperPid is a router/spindle speed controller used in the CNC milling community.
  3597. * Marlin can be used to turn the spindle on and off. It can also be used to set
  3598. * the spindle speed from 5,000 to 30,000 RPM.
  3599. *
  3600. * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
  3601. * hardware PWM pin for the speed control and a pin for the rotation direction.
  3602. *
  3603. * See https://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
  3604. */
  3605. //#define SPINDLE_FEATURE
  3606. //#define LASER_FEATURE
  3607. #if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
  3608. #define SPINDLE_LASER_ACTIVE_STATE LOW // Set to "HIGH" if the on/off function is active HIGH
  3609. #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
  3610. #define SPINDLE_LASER_PWM_INVERT false // Set to "true" if the speed/power goes up when you want it to go slower
  3611.  
  3612.  
  3613.  
  3614.  
  3615. #define SPINDLE_LASER_FREQUENCY 2500 // (Hz) Spindle/laser frequency (only on supported HALs: AVR and LPC)
  3616.  
  3617.  
  3618.  
  3619.  
  3620.  
  3621. //#define AIR_EVACUATION // Cutter Vacuum / Laser Blower motor control with G-codes M10-M11
  3622. #if ENABLED(AIR_EVACUATION)
  3623. #define AIR_EVACUATION_ACTIVE LOW // Set to "HIGH" if the on/off function is active HIGH
  3624. //#define AIR_EVACUATION_PIN 42 // Override the default Cutter Vacuum or Laser Blower pin
  3625. #endif
  3626.  
  3627. //#define AIR_ASSIST // Air Assist control with G-codes M8-M9
  3628. #if ENABLED(AIR_ASSIST)
  3629. #define AIR_ASSIST_ACTIVE LOW // Active state on air assist pin
  3630. //#define AIR_ASSIST_PIN 44 // Override the default Air Assist pin
  3631. #endif
  3632.  
  3633. //#define SPINDLE_SERVO // A servo converting an angle to spindle power
  3634. #ifdef SPINDLE_SERVO
  3635. #define SPINDLE_SERVO_NR 0 // Index of servo used for spindle control
  3636. #define SPINDLE_SERVO_MIN 10 // Minimum angle for servo spindle
  3637. #endif
  3638.  
  3639. /**
  3640. * Speed / Power can be set ('M3 S') and displayed in terms of:
  3641. * - PWM255 (S0 - S255)
  3642. * - PERCENT (S0 - S100)
  3643. * - RPM (S0 - S50000) Best for use with a spindle
  3644. * - SERVO (S0 - S180)
  3645. */
  3646. #define CUTTER_POWER_UNIT PWM255
  3647.  
  3648. /**
  3649. * Relative Cutter Power
  3650. * Normally, 'M3 O<power>' sets
  3651. * OCR power is relative to the range SPEED_POWER_MIN...SPEED_POWER_MAX.
  3652. * so input powers of 0...255 correspond to SPEED_POWER_MIN...SPEED_POWER_MAX
  3653. * instead of normal range (0 to SPEED_POWER_MAX).
  3654. * Best used with (e.g.) SuperPID router controller: S0 = 5,000 RPM and S255 = 30,000 RPM
  3655. */
  3656. //#define CUTTER_POWER_RELATIVE // Set speed proportional to [SPEED_POWER_MIN...SPEED_POWER_MAX]
  3657.  
  3658. #if ENABLED(SPINDLE_FEATURE)
  3659. //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
  3660. #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
  3661. #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
  3662.  
  3663. #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
  3664. #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
  3665.  
  3666. /**
  3667. * M3/M4 Power Equation
  3668. *
  3669. * Each tool uses different value ranges for speed / power control.
  3670. * These parameters are used to convert between tool power units and PWM.
  3671. *
  3672. * Speed/Power = (PWMDC / 255 * 100 - SPEED_POWER_INTERCEPT) / SPEED_POWER_SLOPE
  3673. * PWMDC = (spdpwr - SPEED_POWER_MIN) / (SPEED_POWER_MAX - SPEED_POWER_MIN) / SPEED_POWER_SLOPE
  3674. */
  3675.  
  3676. #define SPEED_POWER_INTERCEPT 0 // (%) 0-100 i.e., Minimum power percentage
  3677. #define SPEED_POWER_MIN 5000 // (RPM)
  3678. #define SPEED_POWER_MAX 30000 // (RPM) SuperPID router controller 0 - 30,000 RPM
  3679. #define SPEED_POWER_STARTUP 25000 // (RPM) M3/M4 speed/power default (with no arguments)
  3680.  
  3681.  
  3682. #else
  3683.  
  3684.  
  3685. #define SPEED_POWER_INTERCEPT 0 // (%) 0-100 i.e., Minimum power percentage
  3686. #define SPEED_POWER_MIN 0 // (%) 0-100
  3687. #define SPEED_POWER_MAX 100 // (%) 0-100
  3688. #define SPEED_POWER_STARTUP 80 // (%) M3/M4 speed/power default (with no arguments)
  3689.  
  3690.  
  3691. // Define the minimum and maximum test pulse time values for a laser test fire function
  3692. #define LASER_TEST_PULSE_MIN 1 // Used with Laser Control Menu
  3693. #define LASER_TEST_PULSE_MAX 999 // Caution: Menu may not show more than 3 characters
  3694.  
  3695.  
  3696.  
  3697.  
  3698.  
  3699.  
  3700.  
  3701.  
  3702.  
  3703.  
  3704.  
  3705.  
  3706.  
  3707.  
  3708. /**
  3709. * Enable inline laser power to be handled in the planner / stepper routines.
  3710. * Inline power is specified by the I (inline) flag in an M3 command (e.g., M3 S20 I)
  3711. * or by the 'S' parameter in G0/G1/G2/G3 moves (see LASER_MOVE_POWER).
  3712. *
  3713. * This allows the laser to keep in perfect sync with the planner and removes
  3714. * the powerup/down delay since lasers require negligible time.
  3715.  
  3716.  
  3717.  
  3718.  
  3719.  
  3720.  
  3721.  
  3722.  
  3723.  
  3724.  
  3725. */
  3726. //#define LASER_POWER_INLINE
  3727.  
  3728. #if ENABLED(LASER_POWER_INLINE)
  3729. /**
  3730. * Scale the laser's power in proportion to the movement rate.
  3731. *
  3732. * - Sets the entry power proportional to the entry speed over the nominal speed.
  3733. * - Ramps the power up every N steps to approximate the speed trapezoid.
  3734. * - Due to the limited power resolution this is only approximate.
  3735. */
  3736. #define LASER_POWER_INLINE_TRAPEZOID
  3737.  
  3738. /**
  3739. * Continuously calculate the current power (nominal_power * current_rate / nominal_rate).
  3740. * Required for accurate power with non-trapezoidal acceleration (e.g., S_CURVE_ACCELERATION).
  3741. * This is a costly calculation so this option is discouraged on 8-bit AVR boards.
  3742. *
  3743. * LASER_POWER_INLINE_TRAPEZOID_CONT_PER defines how many step cycles there are between power updates. If your
  3744. * board isn't able to generate steps fast enough (and you are using LASER_POWER_INLINE_TRAPEZOID_CONT), increase this.
  3745. * Note that when this is zero it means it occurs every cycle; 1 means a delay wait one cycle then run, etc.
  3746. */
  3747. //#define LASER_POWER_INLINE_TRAPEZOID_CONT
  3748.  
  3749. /**
  3750. * Stepper iterations between power updates. Increase this value if the board
  3751. * can't keep up with the processing demands of LASER_POWER_INLINE_TRAPEZOID_CONT.
  3752. * Disable (or set to 0) to recalculate power on every stepper iteration.
  3753. */
  3754. //#define LASER_POWER_INLINE_TRAPEZOID_CONT_PER 10
  3755.  
  3756. /**
  3757. * Include laser power in G0/G1/G2/G3/G5 commands with the 'S' parameter
  3758. */
  3759. //#define LASER_MOVE_POWER
  3760.  
  3761. #if ENABLED(LASER_MOVE_POWER)
  3762. // Turn off the laser on G0 moves with no power parameter.
  3763. // If a power parameter is provided, use that instead.
  3764. //#define LASER_MOVE_G0_OFF
  3765.  
  3766. // Turn off the laser on G28 homing.
  3767. //#define LASER_MOVE_G28_OFF
  3768. #endif
  3769.  
  3770. /**
  3771. * Inline flag inverted
  3772. *
  3773. * WARNING: M5 will NOT turn off the laser unless another move
  3774. * is done (so G-code files must end with 'M5 I').
  3775. */
  3776. //#define LASER_POWER_INLINE_INVERT
  3777.  
  3778. /**
  3779. * Continuously apply inline power. ('M3 S3' == 'G1 S3' == 'M3 S3 I')
  3780. *
  3781. * The laser might do some weird things, so only enable this
  3782. * feature if you understand the implications.
  3783. */
  3784. //#define LASER_POWER_INLINE_CONTINUOUS
  3785.  
  3786. #else
  3787.  
  3788. #define SPINDLE_LASER_POWERUP_DELAY 50 // (ms) Delay to allow the spindle/laser to come up to speed/power
  3789. #define SPINDLE_LASER_POWERDOWN_DELAY 50 // (ms) Delay to allow the spindle to stop
  3790.  
  3791. #endif
  3792.  
  3793.  
  3794.  
  3795.  
  3796.  
  3797.  
  3798.  
  3799.  
  3800. //
  3801. // Laser I2C Ammeter (High precision INA226 low/high side module)
  3802. //
  3803. //#define I2C_AMMETER
  3804. #if ENABLED(I2C_AMMETER)
  3805. #define I2C_AMMETER_IMAX 0.1 // (Amps) Calibration value for the expected current range
  3806. #define I2C_AMMETER_SHUNT_RESISTOR 0.1 // (Ohms) Calibration shunt resistor value
  3807. #endif
  3808.  
  3809.  
  3810.  
  3811.  
  3812.  
  3813.  
  3814.  
  3815.  
  3816.  
  3817.  
  3818.  
  3819.  
  3820.  
  3821.  
  3822.  
  3823. #endif
  3824. #endif // SPINDLE_FEATURE || LASER_FEATURE
  3825.  
  3826. /**
  3827. * Synchronous Laser Control with M106/M107
  3828. *
  3829. * Marlin normally applies M106/M107 fan speeds at a time "soon after" processing
  3830. * a planner block. This is too inaccurate for a PWM/TTL laser attached to the fan
  3831. * header (as with some add-on laser kits). Enable this option to set fan/laser
  3832. * speeds with much more exact timing for improved print fidelity.
  3833. *
  3834. * NOTE: This option sacrifices some cooling fan speed options.
  3835. */
  3836. //#define LASER_SYNCHRONOUS_M106_M107
  3837.  
  3838. /**
  3839. * Coolant Control
  3840. *
  3841. * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off.
  3842. *
  3843. * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined.
  3844. */
  3845. //#define COOLANT_CONTROL
  3846. #if ENABLED(COOLANT_CONTROL)
  3847. #define COOLANT_MIST // Enable if mist coolant is present
  3848. #define COOLANT_FLOOD // Enable if flood coolant is present
  3849. #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed
  3850. #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed
  3851. #endif
  3852.  
  3853. /**
  3854. * Filament Width Sensor
  3855. *
  3856. * Measures the filament width in real-time and adjusts
  3857. * flow rate to compensate for any irregularities.
  3858. *
  3859. * Also allows the measured filament diameter to set the
  3860. * extrusion rate, so the slicer only has to specify the
  3861. * volume.
  3862. *
  3863. * Only a single extruder is supported at this time.
  3864. *
  3865. * 34 RAMPS_14 : Analog input 5 on the AUX2 connector
  3866. * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
  3867. * 301 RAMBO : Analog input 3
  3868. *
  3869. * Note: May require analog pins to be defined for other boards.
  3870. */
  3871. //#define FILAMENT_WIDTH_SENSOR
  3872.  
  3873. #if ENABLED(FILAMENT_WIDTH_SENSOR)
  3874. #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
  3875. #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
  3876.  
  3877. #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it
  3878. #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
  3879.  
  3880. #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
  3881.  
  3882. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
  3883. //#define FILAMENT_LCD_DISPLAY
  3884. #endif
  3885.  
  3886. /**
  3887. * Power Monitor
  3888. * Monitor voltage (V) and/or current (A), and -when possible- power (W)
  3889. *
  3890. * Read and configure with M430
  3891. *
  3892. * The current sensor feeds DC voltage (relative to the measured current) to an analog pin
  3893. * The voltage sensor feeds DC voltage (relative to the measured voltage) to an analog pin
  3894. */
  3895. //#define POWER_MONITOR_CURRENT // Monitor the system current
  3896. //#define POWER_MONITOR_VOLTAGE // Monitor the system voltage
  3897.  
  3898. #if ENABLED(POWER_MONITOR_CURRENT)
  3899. #define POWER_MONITOR_VOLTS_PER_AMP 0.05000 // Input voltage to the MCU analog pin per amp - DO NOT apply more than ADC_VREF!
  3900. #define POWER_MONITOR_CURRENT_OFFSET 0 // Offset (in amps) applied to the calculated current
  3901. #define POWER_MONITOR_FIXED_VOLTAGE 13.6 // Voltage for a current sensor with no voltage sensor (for power display)
  3902. #endif
  3903.  
  3904. #if ENABLED(POWER_MONITOR_VOLTAGE)
  3905. #define POWER_MONITOR_VOLTS_PER_VOLT 0.077933 // Input voltage to the MCU analog pin per volt - DO NOT apply more than ADC_VREF!
  3906. #define POWER_MONITOR_VOLTAGE_OFFSET 0 // Offset (in volts) applied to the calculated voltage
  3907. #endif
  3908.  
  3909. /**
  3910. * Stepper Driver Anti-SNAFU Protection
  3911. *
  3912. * If the SAFE_POWER_PIN is defined for your board, Marlin will check
  3913. * that stepper drivers are properly plugged in before applying power.
  3914. * Disable protection if your stepper drivers don't support the feature.
  3915. */
  3916. #define DISABLE_DRIVER_SAFE_POWER_PROTECT
  3917.  
  3918. /**
  3919. * CNC Coordinate Systems
  3920. *
  3921. * Enables G53 and G54-G59.3 commands to select coordinate systems
  3922. * and G92.1 to reset the workspace to native machine space.
  3923. */
  3924. //#define CNC_COORDINATE_SYSTEMS
  3925.  
  3926. /**
  3927.  
  3928.  
  3929.  
  3930.  
  3931.  
  3932.  
  3933. * Auto-report temperatures with M155 S<seconds>
  3934. */
  3935. #define AUTO_REPORT_TEMPERATURES
  3936.  
  3937.  
  3938.  
  3939.  
  3940. /**
  3941. * Auto-report position with M154 S<seconds>
  3942. */
  3943. //#define AUTO_REPORT_POSITION
  3944.  
  3945. /**
  3946. * Include capabilities in M115 output
  3947. */
  3948. #define EXTENDED_CAPABILITIES_REPORT
  3949. #if ENABLED(EXTENDED_CAPABILITIES_REPORT)
  3950. #define M115_GEOMETRY_REPORT
  3951. #endif
  3952.  
  3953. /**
  3954. * Expected Printer Check
  3955. * Add the M16 G-code to compare a string to the MACHINE_NAME.
  3956. * M16 with a non-matching string causes the printer to halt.
  3957. */
  3958. //#define EXPECTED_PRINTER_CHECK
  3959.  
  3960. /**
  3961. * Disable all Volumetric extrusion options
  3962. */
  3963. //#define NO_VOLUMETRICS
  3964.  
  3965. #if DISABLED(NO_VOLUMETRICS)
  3966. /**
  3967. * Volumetric extrusion default state
  3968. * Activate to make volumetric extrusion the default method,
  3969. * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter.
  3970. *
  3971. * M200 D0 to disable, M200 Dn to set a new diameter (and enable volumetric).
  3972. * M200 S0/S1 to disable/enable volumetric extrusion.
  3973. */
  3974. //#define VOLUMETRIC_DEFAULT_ON
  3975.  
  3976. //#define VOLUMETRIC_EXTRUDER_LIMIT
  3977. #if ENABLED(VOLUMETRIC_EXTRUDER_LIMIT)
  3978. /**
  3979. * Default volumetric extrusion limit in cubic mm per second (mm^3/sec).
  3980. * This factory setting applies to all extruders.
  3981. * Use 'M200 [T<extruder>] L<limit>' to override and 'M502' to reset.
  3982. * A non-zero value activates Volume-based Extrusion Limiting.
  3983. */
  3984. #define DEFAULT_VOLUMETRIC_EXTRUDER_LIMIT 0.00 // (mm^3/sec)
  3985. #endif
  3986. #endif
  3987.  
  3988. /**
  3989. * Enable this option for a leaner build of Marlin that removes all
  3990. * workspace offsets, simplifying coordinate transformations, leveling, etc.
  3991. *
  3992. * - M206 and M428 are disabled.
  3993. * - G92 will revert to its behavior from Marlin 1.0.
  3994. */
  3995. //#define NO_WORKSPACE_OFFSETS
  3996.  
  3997. // Extra options for the M114 "Current Position" report
  3998. #define M114_DETAIL // Use 'M114` for details to check planner calculations
  3999. //#define M114_REALTIME // Real current position based on forward kinematics
  4000. //#define M114_LEGACY // M114 used to synchronize on every call. Enable if needed.
  4001.  
  4002. #define REPORT_FAN_CHANGE // Report the new fan speed when changed by M106 (and others)
  4003.  
  4004. /**
  4005. * Set the number of proportional font spaces required to fill up a typical character space.
  4006. * This can help to better align the output of commands like `G29 O` Mesh Output.
  4007. *
  4008. * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0.
  4009. * Otherwise, adjust according to your client and font.
  4010. */
  4011. #define PROPORTIONAL_FONT_RATIO 1.0
  4012.  
  4013. /**
  4014. * Spend 28 bytes of SRAM to optimize the G-code parser
  4015. */
  4016. #define FASTER_GCODE_PARSER
  4017.  
  4018. #if ENABLED(FASTER_GCODE_PARSER)
  4019. //#define GCODE_QUOTED_STRINGS // Support for quoted string parameters
  4020. #endif
  4021.  
  4022. // Support for MeatPack G-code compression (https://github.com/scottmudge/OctoPrint-MeatPack)
  4023. //#define MEATPACK_ON_SERIAL_PORT_1
  4024. //#define MEATPACK_ON_SERIAL_PORT_2
  4025.  
  4026. //#define GCODE_CASE_INSENSITIVE // Accept G-code sent to the firmware in lowercase
  4027.  
  4028. //#define REPETIER_GCODE_M360 // Add commands originally from Repetier FW
  4029.  
  4030. /**
  4031. * CNC G-code options
  4032. * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc.
  4033. * Note that G0 feedrates should be used with care for 3D printing (if used at all).
  4034. * High feedrates may cause ringing and harm print quality.
  4035. */
  4036. //#define PAREN_COMMENTS // Support for parentheses-delimited comments
  4037. //#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc.
  4038.  
  4039. // Enable and set a (default) feedrate for all G0 moves
  4040. //#define G0_FEEDRATE 3000 // (mm/min)
  4041. #ifdef G0_FEEDRATE
  4042. //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
  4043. #endif
  4044.  
  4045. /**
  4046. * Startup commands
  4047. *
  4048. * Execute certain G-code commands immediately after power-on.
  4049. */
  4050. //#define STARTUP_COMMANDS "M17 Z"
  4051.  
  4052. /**
  4053. * G-code Macros
  4054. *
  4055. * Add G-codes M810-M819 to define and run G-code macros.
  4056. * Macros are not saved to EEPROM.
  4057. */
  4058. //#define GCODE_MACROS
  4059. #if ENABLED(GCODE_MACROS)
  4060. #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used
  4061. #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro
  4062. #endif
  4063.  
  4064. /**
  4065. * User-defined menu items to run custom G-code.
  4066. * Up to 25 may be defined, but the actual number is LCD-dependent.
  4067. */
  4068.  
  4069. // Custom Menu: Main Menu
  4070. //#define CUSTOM_MENU_MAIN
  4071. #if ENABLED(CUSTOM_MENU_MAIN)
  4072. //#define CUSTOM_MENU_MAIN_TITLE "Custom Commands"
  4073. #define CUSTOM_MENU_MAIN_SCRIPT_DONE "M117 User Script Done"
  4074. #define CUSTOM_MENU_MAIN_SCRIPT_AUDIBLE_FEEDBACK
  4075. //#define CUSTOM_MENU_MAIN_SCRIPT_RETURN // Return to status screen after a script
  4076. #define CUSTOM_MENU_MAIN_ONLY_IDLE // Only show custom menu when the machine is idle
  4077.  
  4078. #define MAIN_MENU_ITEM_1_DESC "Home & UBL Info"
  4079. #define MAIN_MENU_ITEM_1_GCODE "G28\nG29 W"
  4080. //#define MAIN_MENU_ITEM_1_CONFIRM // Show a confirmation dialog before this action
  4081.  
  4082. #define MAIN_MENU_ITEM_2_DESC "Preheat for " PREHEAT_1_LABEL
  4083. #define MAIN_MENU_ITEM_2_GCODE "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
  4084. //#define MAIN_MENU_ITEM_2_CONFIRM
  4085.  
  4086. //#define MAIN_MENU_ITEM_3_DESC "Preheat for " PREHEAT_2_LABEL
  4087. //#define MAIN_MENU_ITEM_3_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
  4088. //#define MAIN_MENU_ITEM_3_CONFIRM
  4089.  
  4090. //#define MAIN_MENU_ITEM_4_DESC "Heat Bed/Home/Level"
  4091. //#define MAIN_MENU_ITEM_4_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
  4092. //#define MAIN_MENU_ITEM_4_CONFIRM
  4093.  
  4094. //#define MAIN_MENU_ITEM_5_DESC "Home & Info"
  4095. //#define MAIN_MENU_ITEM_5_GCODE "G28\nM503"
  4096. //#define MAIN_MENU_ITEM_5_CONFIRM
  4097. #endif
  4098.  
  4099. // Custom Menu: Configuration Menu
  4100. //#define CUSTOM_MENU_CONFIG
  4101. #if ENABLED(CUSTOM_MENU_CONFIG)
  4102. //#define CUSTOM_MENU_CONFIG_TITLE "Custom Commands"
  4103. #define CUSTOM_MENU_CONFIG_SCRIPT_DONE "M117 Wireless Script Done"
  4104. #define CUSTOM_MENU_CONFIG_SCRIPT_AUDIBLE_FEEDBACK
  4105. //#define CUSTOM_MENU_CONFIG_SCRIPT_RETURN // Return to status screen after a script
  4106. #define CUSTOM_MENU_CONFIG_ONLY_IDLE // Only show custom menu when the machine is idle
  4107.  
  4108. #define CONFIG_MENU_ITEM_1_DESC "Wifi ON"
  4109. #define CONFIG_MENU_ITEM_1_GCODE "M118 [ESP110] WIFI-STA pwd=12345678"
  4110. //#define CONFIG_MENU_ITEM_1_CONFIRM // Show a confirmation dialog before this action
  4111.  
  4112. #define CONFIG_MENU_ITEM_2_DESC "Bluetooth ON"
  4113. #define CONFIG_MENU_ITEM_2_GCODE "M118 [ESP110] BT pwd=12345678"
  4114. //#define CONFIG_MENU_ITEM_2_CONFIRM
  4115.  
  4116. //#define CONFIG_MENU_ITEM_3_DESC "Radio OFF"
  4117. //#define CONFIG_MENU_ITEM_3_GCODE "M118 [ESP110] OFF pwd=12345678"
  4118. //#define CONFIG_MENU_ITEM_3_CONFIRM
  4119.  
  4120. //#define CONFIG_MENU_ITEM_4_DESC "Wifi ????"
  4121. //#define CONFIG_MENU_ITEM_4_GCODE "M118 ????"
  4122. //#define CONFIG_MENU_ITEM_4_CONFIRM
  4123.  
  4124. //#define CONFIG_MENU_ITEM_5_DESC "Wifi ????"
  4125. //#define CONFIG_MENU_ITEM_5_GCODE "M118 ????"
  4126. //#define CONFIG_MENU_ITEM_5_CONFIRM
  4127. #endif
  4128.  
  4129. /**
  4130. * User-defined buttons to run custom G-code.
  4131. * Up to 25 may be defined.
  4132. */
  4133. //#define CUSTOM_USER_BUTTONS
  4134. #if ENABLED(CUSTOM_USER_BUTTONS)
  4135. //#define BUTTON1_PIN -1
  4136. #if PIN_EXISTS(BUTTON1)
  4137. #define BUTTON1_HIT_STATE LOW // State of the triggered button. NC=LOW. NO=HIGH.
  4138. #define BUTTON1_WHEN_PRINTING false // Button allowed to trigger during printing?
  4139. #define BUTTON1_GCODE "G28"
  4140. #define BUTTON1_DESC "Homing" // Optional string to set the LCD status
  4141. #endif
  4142.  
  4143. //#define BUTTON2_PIN -1
  4144. #if PIN_EXISTS(BUTTON2)
  4145. #define BUTTON2_HIT_STATE LOW
  4146. #define BUTTON2_WHEN_PRINTING false
  4147. #define BUTTON2_GCODE "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
  4148. #define BUTTON2_DESC "Preheat for " PREHEAT_1_LABEL
  4149. #endif
  4150.  
  4151. //#define BUTTON3_PIN -1
  4152. #if PIN_EXISTS(BUTTON3)
  4153. #define BUTTON3_HIT_STATE LOW
  4154. #define BUTTON3_WHEN_PRINTING false
  4155. #define BUTTON3_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
  4156. #define BUTTON3_DESC "Preheat for " PREHEAT_2_LABEL
  4157. #endif
  4158. #endif
  4159.  
  4160. /**
  4161. * Host Action Commands
  4162. *
  4163. * Define host streamer action commands in compliance with the standard.
  4164. *
  4165. * See https://reprap.org/wiki/G-code#Action_commands
  4166. * Common commands ........ poweroff, pause, paused, resume, resumed, cancel
  4167. * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed
  4168. *
  4169. * Some features add reason codes to extend these commands.
  4170. *
  4171. * Host Prompt Support enables Marlin to use the host for user prompts so
  4172. * filament runout and other processes can be managed from the host side.
  4173. */
  4174. #define HOST_ACTION_COMMANDS
  4175. #if ENABLED(HOST_ACTION_COMMANDS)
  4176.  
  4177.  
  4178. #define HOST_PROMPT_SUPPORT
  4179.  
  4180.  
  4181. //#define HOST_START_MENU_ITEM // Add a menu item that tells the host to start
  4182.  
  4183. #endif
  4184.  
  4185. /**
  4186. * Cancel Objects
  4187. *
  4188. * Implement M486 to allow Marlin to skip objects
  4189. */
  4190. //#define CANCEL_OBJECTS
  4191. #if ENABLED(CANCEL_OBJECTS)
  4192. #define CANCEL_OBJECTS_REPORTING // Emit the current object as a status message
  4193. #endif
  4194.  
  4195. /**
  4196. * I2C position encoders for closed loop control.
  4197. * Developed by Chris Barr at Aus3D.
  4198. *
  4199. * Wiki: https://wiki.aus3d.com.au/Magnetic_Encoder
  4200. * Github: https://github.com/Aus3D/MagneticEncoder
  4201. *
  4202. * Supplier: https://aus3d.com.au/magnetic-encoder-module
  4203. * Alternative Supplier: https://reliabuild3d.com/
  4204. *
  4205. * Reliabuild encoders have been modified to improve reliability.
  4206. */
  4207.  
  4208. //#define I2C_POSITION_ENCODERS
  4209. #if ENABLED(I2C_POSITION_ENCODERS)
  4210.  
  4211. #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5
  4212. // encoders supported currently.
  4213.  
  4214. #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200.
  4215. #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. <X|Y|Z|E>_AXIS.
  4216. #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or-
  4217. // I2CPE_ENC_TYPE_ROTARY.
  4218. #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for
  4219. // 1mm poles. For linear encoders this is ticks / mm,
  4220. // for rotary encoders this is ticks / revolution.
  4221. //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper
  4222. // steps per full revolution (motor steps/rev * microstepping)
  4223. //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel.
  4224. #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction.
  4225. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the
  4226. // printer will attempt to correct the error; errors
  4227. // smaller than this are ignored to minimize effects of
  4228. // measurement noise / latency (filter).
  4229.  
  4230. #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2.
  4231. #define I2CPE_ENC_2_AXIS Y_AXIS
  4232. #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR
  4233. #define I2CPE_ENC_2_TICKS_UNIT 2048
  4234. //#define I2CPE_ENC_2_TICKS_REV (16 * 200)
  4235. //#define I2CPE_ENC_2_INVERT
  4236. #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP
  4237. #define I2CPE_ENC_2_EC_THRESH 0.10
  4238.  
  4239. #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options
  4240. #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below.
  4241.  
  4242. #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4.
  4243. #define I2CPE_ENC_4_AXIS E_AXIS
  4244.  
  4245. #define I2CPE_ENC_5_ADDR 34 // Encoder 5.
  4246. #define I2CPE_ENC_5_AXIS E_AXIS
  4247.  
  4248. // Default settings for encoders which are enabled, but without settings configured above.
  4249. #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR
  4250. #define I2CPE_DEF_ENC_TICKS_UNIT 2048
  4251. #define I2CPE_DEF_TICKS_REV (16 * 200)
  4252. #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE
  4253. #define I2CPE_DEF_EC_THRESH 0.1
  4254.  
  4255. //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
  4256. // axis after which the printer will abort. Comment out to
  4257. // disable abort behavior.
  4258.  
  4259. #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
  4260. // for this amount of time (in ms) before the encoder
  4261. // is trusted again.
  4262.  
  4263. /**
  4264. * Position is checked every time a new command is executed from the buffer but during long moves,
  4265. * this setting determines the minimum update time between checks. A value of 100 works well with
  4266. * error rolling average when attempting to correct only for skips and not for vibration.
  4267. */
  4268. #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks.
  4269.  
  4270. // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
  4271. #define I2CPE_ERR_ROLLING_AVERAGE
  4272.  
  4273. #endif // I2C_POSITION_ENCODERS
  4274.  
  4275. /**
  4276. * Analog Joystick(s)
  4277. */
  4278. //#define JOYSTICK
  4279. #if ENABLED(JOYSTICK)
  4280. #define JOY_X_PIN 5 // RAMPS: Suggested pin A5 on AUX2
  4281. #define JOY_Y_PIN 10 // RAMPS: Suggested pin A10 on AUX2
  4282. #define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
  4283. #define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
  4284.  
  4285. //#define INVERT_JOY_X // Enable if X direction is reversed
  4286. //#define INVERT_JOY_Y // Enable if Y direction is reversed
  4287. //#define INVERT_JOY_Z // Enable if Z direction is reversed
  4288.  
  4289. // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
  4290. #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
  4291. #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
  4292. #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
  4293. //#define JOYSTICK_DEBUG
  4294. #endif
  4295.  
  4296. /**
  4297. * Mechanical Gantry Calibration
  4298. * Modern replacement for the Prusa TMC_Z_CALIBRATION.
  4299. * Adds capability to work with any adjustable current drivers.
  4300. * Implemented as G34 because M915 is deprecated.
  4301. */
  4302. //#define MECHANICAL_GANTRY_CALIBRATION
  4303. #if ENABLED(MECHANICAL_GANTRY_CALIBRATION)
  4304. #define GANTRY_CALIBRATION_CURRENT 600 // Default calibration current in ma
  4305. #define GANTRY_CALIBRATION_EXTRA_HEIGHT 15 // Extra distance in mm past Z_###_POS to move
  4306. #define GANTRY_CALIBRATION_FEEDRATE 500 // Feedrate for correction move
  4307. //#define GANTRY_CALIBRATION_TO_MIN // Enable to calibrate Z in the MIN direction
  4308.  
  4309. //#define GANTRY_CALIBRATION_SAFE_POSITION XY_CENTER // Safe position for nozzle
  4310. //#define GANTRY_CALIBRATION_XY_PARK_FEEDRATE 3000 // XY Park Feedrate - MMM
  4311. //#define GANTRY_CALIBRATION_COMMANDS_PRE ""
  4312. #define GANTRY_CALIBRATION_COMMANDS_POST "G28" // G28 highly recommended to ensure an accurate position
  4313. #endif
  4314.  
  4315. /**
  4316. * Instant freeze / unfreeze functionality
  4317. * Specified pin has pullup and connecting to ground will instantly pause motion.
  4318. * Potentially useful for emergency stop that allows being resumed.
  4319. */
  4320. //#define FREEZE_FEATURE
  4321. #if ENABLED(FREEZE_FEATURE)
  4322. //#define FREEZE_PIN 41 // Override the default (KILL) pin here
  4323.  
  4324. #endif
  4325.  
  4326. /**
  4327. * MAX7219 Debug Matrix
  4328. *
  4329. * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display.
  4330. * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage.
  4331. */
  4332. //#define MAX7219_DEBUG
  4333. #if ENABLED(MAX7219_DEBUG)
  4334. #define MAX7219_CLK_PIN 64
  4335. #define MAX7219_DIN_PIN 57
  4336. #define MAX7219_LOAD_PIN 44
  4337.  
  4338. //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix
  4339. #define MAX7219_INIT_TEST 2 // Test pattern at startup: 0=none, 1=sweep, 2=spiral
  4340. #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain.
  4341. #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°)
  4342. // connector at: right=0 bottom=-90 top=90 left=180
  4343. //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order
  4344. //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side
  4345.  
  4346. /**
  4347. * Sample debug features
  4348. * If you add more debug displays, be careful to avoid conflicts!
  4349. */
  4350. #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning
  4351. #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row
  4352. #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row
  4353.  
  4354. #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row
  4355. // If you experience stuttering, reboots, etc. this option can reveal how
  4356. // tweaks made to the configuration are affecting the printer in real-time.
  4357. #endif
  4358.  
  4359. /**
  4360. * NanoDLP Sync support
  4361. *
  4362. * Support for Synchronized Z moves when used with NanoDLP. G0/G1 axis moves will
  4363. * output a "Z_move_comp" string to enable synchronization with DLP projector exposure.
  4364. * This feature allows you to use [[WaitForDoneMessage]] instead of M400 commands.
  4365. */
  4366. //#define NANODLP_Z_SYNC
  4367. #if ENABLED(NANODLP_Z_SYNC)
  4368. //#define NANODLP_ALL_AXIS // Send a "Z_move_comp" report for any axis move (not just Z).
  4369. #endif
  4370.  
  4371. /**
  4372. * Ethernet. Use M552 to enable and set the IP address.
  4373. */
  4374. #if HAS_ETHERNET
  4375. #define MAC_ADDRESS { 0xDE, 0xAD, 0xBE, 0xEF, 0xF0, 0x0D } // A MAC address unique to your network
  4376. #endif
  4377.  
  4378. /**
  4379. * WiFi Support (Espressif ESP32 WiFi)
  4380. */
  4381. //#define WIFISUPPORT // Marlin embedded WiFi managenent
  4382. //#define ESP3D_WIFISUPPORT // ESP3D Library WiFi management (https://github.com/luc-github/ESP3DLib)
  4383.  
  4384. #if EITHER(WIFISUPPORT, ESP3D_WIFISUPPORT)
  4385. //#define WEBSUPPORT // Start a webserver (which may include auto-discovery)
  4386. //#define OTASUPPORT // Support over-the-air firmware updates
  4387. //#define WIFI_CUSTOM_COMMAND // Accept feature config commands (e.g., WiFi ESP3D) from the host
  4388.  
  4389. /**
  4390. * To set a default WiFi SSID / Password, create a file called Configuration_Secure.h with
  4391. * the following defines, customized for your network. This specific file is excluded via
  4392. * .gitignore to prevent it from accidentally leaking to the public.
  4393. *
  4394. * #define WIFI_SSID "WiFi SSID"
  4395. * #define WIFI_PWD "WiFi Password"
  4396. */
  4397. //#include "Configuration_Secure.h" // External file with WiFi SSID / Password
  4398. #endif
  4399.  
  4400. /**
  4401. * Průša Multi-Material Unit (MMU)
  4402. * Enable in Configuration.h
  4403. *
  4404. * These devices allow a single stepper driver on the board to drive
  4405. * multi-material feeders with any number of stepper motors.
  4406. */
  4407. #if HAS_PRUSA_MMU1
  4408. /**
  4409. * This option only allows the multiplexer to switch on tool-change.
  4410. * Additional options to configure custom E moves are pending.
  4411. *
  4412. * Override the default DIO selector pins here, if needed.
  4413. * Some pins files may provide defaults for these pins.
  4414. */
  4415. //#define E_MUX0_PIN 40 // Always Required
  4416. //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs
  4417. //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs
  4418. #elif HAS_PRUSA_MMU2
  4419. // Serial port used for communication with MMU2.
  4420. #define MMU2_SERIAL_PORT 2
  4421.  
  4422. // Use hardware reset for MMU if a pin is defined for it
  4423. //#define MMU2_RST_PIN 23
  4424.  
  4425. // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up)
  4426. //#define MMU2_MODE_12V
  4427.  
  4428. // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout
  4429. #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600"
  4430.  
  4431. // Add an LCD menu for MMU2
  4432. //#define MMU2_MENUS
  4433. #if EITHER(MMU2_MENUS, HAS_PRUSA_MMU2S)
  4434. // Settings for filament load / unload from the LCD menu.
  4435. // This is for Průša MK3-style extruders. Customize for your hardware.
  4436. #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0
  4437. #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \
  4438. { 7.2, 1145 }, \
  4439. { 14.4, 871 }, \
  4440. { 36.0, 1393 }, \
  4441. { 14.4, 871 }, \
  4442. { 50.0, 198 }
  4443.  
  4444. #define MMU2_RAMMING_SEQUENCE \
  4445. { 1.0, 1000 }, \
  4446. { 1.0, 1500 }, \
  4447. { 2.0, 2000 }, \
  4448. { 1.5, 3000 }, \
  4449. { 2.5, 4000 }, \
  4450. { -15.0, 5000 }, \
  4451. { -14.0, 1200 }, \
  4452. { -6.0, 600 }, \
  4453. { 10.0, 700 }, \
  4454. { -10.0, 400 }, \
  4455. { -50.0, 2000 }
  4456. #endif
  4457.  
  4458. /**
  4459. * Using a sensor like the MMU2S
  4460. * This mode requires a MK3S extruder with a sensor at the extruder idler, like the MMU2S.
  4461. * See https://help.prusa3d.com/en/guide/3b-mk3s-mk2-5s-extruder-upgrade_41560, step 11
  4462. */
  4463. #if HAS_PRUSA_MMU2S
  4464. #define MMU2_C0_RETRY 5 // Number of retries (total time = timeout*retries)
  4465.  
  4466. #define MMU2_CAN_LOAD_FEEDRATE 800 // (mm/min)
  4467. #define MMU2_CAN_LOAD_SEQUENCE \
  4468. { 0.1, MMU2_CAN_LOAD_FEEDRATE }, \
  4469. { 60.0, MMU2_CAN_LOAD_FEEDRATE }, \
  4470. { -52.0, MMU2_CAN_LOAD_FEEDRATE }
  4471.  
  4472. #define MMU2_CAN_LOAD_RETRACT 6.0 // (mm) Keep under the distance between Load Sequence values
  4473. #define MMU2_CAN_LOAD_DEVIATION 0.8 // (mm) Acceptable deviation
  4474.  
  4475. #define MMU2_CAN_LOAD_INCREMENT 0.2 // (mm) To reuse within MMU2 module
  4476. #define MMU2_CAN_LOAD_INCREMENT_SEQUENCE \
  4477. { -MMU2_CAN_LOAD_INCREMENT, MMU2_CAN_LOAD_FEEDRATE }
  4478.  
  4479. #else
  4480.  
  4481. /**
  4482. * MMU1 Extruder Sensor
  4483. *
  4484. * Support for a Průša (or other) IR Sensor to detect filament near the extruder
  4485. * and make loading more reliable. Suitable for an extruder equipped with a filament
  4486. * sensor less than 38mm from the gears.
  4487. *
  4488. * During loading the extruder will stop when the sensor is triggered, then do a last
  4489. * move up to the gears. If no filament is detected, the MMU2 can make some more attempts.
  4490. * If all attempts fail, a filament runout will be triggered.
  4491. */
  4492. //#define MMU_EXTRUDER_SENSOR
  4493. #if ENABLED(MMU_EXTRUDER_SENSOR)
  4494. #define MMU_LOADING_ATTEMPTS_NR 5 // max. number of attempts to load filament if first load fail
  4495. #endif
  4496.  
  4497. #endif
  4498.  
  4499. //#define MMU2_DEBUG // Write debug info to serial output
  4500.  
  4501. #endif // HAS_PRUSA_MMU2
  4502.  
  4503. /**
  4504. * Advanced Print Counter settings
  4505. */
  4506. #if ENABLED(PRINTCOUNTER)
  4507. #define SERVICE_WARNING_BUZZES 3
  4508. // Activate up to 3 service interval watchdogs
  4509. //#define SERVICE_NAME_1 "Service S"
  4510. //#define SERVICE_INTERVAL_1 100 // print hours
  4511. //#define SERVICE_NAME_2 "Service L"
  4512. //#define SERVICE_INTERVAL_2 200 // print hours
  4513. //#define SERVICE_NAME_3 "Service 3"
  4514. //#define SERVICE_INTERVAL_3 1 // print hours
  4515. #endif
  4516.  
  4517. // @section develop
  4518.  
  4519. //
  4520. // M100 Free Memory Watcher to debug memory usage
  4521. //
  4522. //#define M100_FREE_MEMORY_WATCHER
  4523.  
  4524. //
  4525. // M42 - Set pin states
  4526. //
  4527. #define DIRECT_PIN_CONTROL
  4528.  
  4529. //
  4530. // M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe
  4531. //
  4532. #define PINS_DEBUGGING
  4533.  
  4534. // Enable Marlin dev mode which adds some special commands
  4535. //#define MARLIN_DEV_MODE
  4536.  
  4537.  
  4538.  
  4539.  
  4540.  
  4541.  
  4542.  
  4543.  
  4544.  
  4545. /**
  4546. * Postmortem Debugging captures misbehavior and outputs the CPU status and backtrace to serial.
  4547. * When running in the debugger it will break for debugging. This is useful to help understand
  4548. * a crash from a remote location. Requires ~400 bytes of SRAM and 5Kb of flash.
  4549. */
  4550. //#define POSTMORTEM_DEBUGGING
  4551.  
  4552. /**
  4553. * Software Reset options
  4554. */
  4555. //#define SOFT_RESET_VIA_SERIAL // 'KILL' and '^X' commands will soft-reset the controller
  4556. //#define SOFT_RESET_ON_KILL // Use a digital button to soft-reset the controller after KILL
  4557.  
  4558.  
  4559.  
  4560.  
Tags: Configuration_adv
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!