WD TV Live Streaming Media Player Gen3 bootloop TTl output

Using UART port 0 as console.
xmboot booted from devtype: 0, chipsel: 0, phyblocknum: 0, devflags: 1
Explicit boot order specified:
  0x00 : devtype=0, CS=0
  0x01 : devtype=0, CS=1
  0x40 : devtype=4, CS=0
  0x41 : devtype=4, CS=1
ezboot buffers, setup in DRAM bank#0:
  Alloting 2097152 bytes for heap.
  Alloting 16777216 bytes for reading.
  Alloting 16777216 bytes for decryption.
xmat romfs goes to 0x9e3fbfe0 (ga)
xmat romfs goes to 0xb63fbfe0 (va)
Trying devtype=0 chipsel=0
xmboot booted from NAND, setting device flags = 0x010b1000
nandlib_init(cs=0, reserved_phyblocks=4096, pagesize_shift=11, extecc=1
nand_probe 0x0xd0103854
reserved phyblocks exceeds range, skipping ..
Reading xmaterial from BBA physical zone
Reading NAND CS0, addr 0x00d80000, size 0x00000800 to 0xb63fbfe0
Reading NAND CS0, addr 0x00d80800, size 0x00022400 to 0xb63fc7e0
File xtask_loader.xload found
process_imat_romfs,1523
get_firmware_sign,1469: *sign=6c696166
get_firmware_sign,1473: *sign=6c696166,size=4
found imat romfs @ 0x01c80000
imap romfs goes to 0x9dffbfc0 (ga)
imap romfs goes to 0xb5ffbfc0 (va)
Trying devtype=0 chipsel=0
xmboot booted from NAND, setting device flags = 0x010b1000
Reading imaterial from BBA physical zone
Reading NAND CS0, addr 0x01c80000, size 0x00000800 to 0xb5ffbfc0
Reading NAND CS0, addr 0x01c80800, size 0x003aac00 to 0xb5ffc7c0
File itask_loader.iload found
Channel pending 1612
Channel pending 1369970
Channel pending 2932354
Channel pending 4494782
Channel pending 6057238
Channel pending 7619694
Channel pending 9182114
Channel pending 10744506
Channel pending 12369478
Trying devtype=0 chipsel=0
xmboot booted from NAND, setting device flags = 0x010b1000
reading z.boot2 (vzx=0xba7fbff4) is 0x00780000, BBA physical zone
Reading NAND CS0, addr 0x00780000, size 0x00000800 to 0x01840000
Reading NAND CS0, addr 0x00780800, size 0x00400c00 to 0x01840800
Found.
ROMFS found at 0x0x01840000, Volume name = MIPSLINUX_XLOAD
Found 1 file(s) to be processed in ROMFS.
Processing vmlinux_xload.zbf (start: 0x01840090, size: 0x004010d4)
  Checking zboot file signature .. OK.
  Warning: header version mismatched.
   *** Fully Encrypted.
src_addr = 0x018400b0, dest addr = 0x02840000
XLOADING src=0x818400b0, dest=0x82840000, size=0x004010b4
xload.c:68: Waiting for XLOAD completion.
xload.c:78: XLOAD done, status = 0x6.
  Decompressing to 0x84000000 .. OK (6987763/0x6a9ff3).
  Load time total 0/0 msec.
Execute at 0x844ac000 ..
Linux version 2.6.22.19-49-4 (release@TP-SERVER2) (gcc version 4.3.2 (Sourcery G++ Lite 4.3-51) ) #11 PREEMPT Mon Mar 26 18:01:20 CST 2012
Mixed DRAM usage enabled.
Configured for SMP8670, detected SMP8670 (revision ES2).
Detected CPU/System/DSP Frequencies: 715.50/357.75/357.75MHz
SMP86xx Enabled Devices under Linux/XENV 0x9e7fbff4 = 0x003002f0
 Ethernet1 IR FIP I2CM I2CS SDIO1 USB
Desired kernel memory size: 0x05000000
Max. DRAM0/1 size allowed: 0x0ca00000/0x00000000
 Mapped 0x80000000(size 0x04000000) via remap2
 Mapped 0x84000000(size 0x01000000) via remap3
Final kernel memory size: 0x05000000
CPU revision is: 0001937c
FPU revision is: 01739300
Determined physical RAM map:
 memory: 05000000 @ 04000000 (usable)
Desired kernel memory size: 0x0c800000
Max. DRAM0/1 size allowed: 0x0ca00000/0x00000000
 Mapped 0x80000000(size 0x04000000) via remap2
 Mapped 0x84000000(size 0x04000000) via remap3
 Mapped 0x88000000(size 0x04000000) via remap4
 Mapped 0x8c000000(size 0x00800000) via remap5
Final kernel memory size: 0x0c800000
User-defined physical RAM map:
 memory: 0c800000 @ 04000000 (usable)
Wasting 131072 bytes for tracking 4096 unused pages
Initrd not found or empty - disabling initrd
On node 0 totalpages: 16896
  DMA zone: 33 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 16863 pages, LIFO batch:3
  Normal zone: 0 pages used for memmap
Built 1 zonelists.  Total pages: 16863
Kernel command line: console=ttyS0 mem=200M
Primary instruction cache 32kB, 4-way, physically tagged, linesize 32 bytes.
Primary data cache 32kB, 4-way, physically tagged, no aliases, linesize 32 bytes
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 2048 (order: 11, 8192 bytes)
Using 357.750 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 4, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 3, 131072 bytes)
Memory: 196144k/204800k available (3926k kernel code, 8432k reserved, 841k data, 2048k init, 0k highmem)
Calibrating delay loop... 476.77 BogoMIPS (lpj=2383872)
Mount-cache hash table entries: 2048
NET: Registered protocol family 16
PCI: pci host support disabled
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: TANGOX clocksource has been installed.
IP route cache hash table entries: 4096 (order: 0, 16384 bytes)
TCP established hash table entries: 16384 (order: 3, 131072 bytes)
TCP bind hash table entries: 16384 (order: 2, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
cp0_timer: interrupt registered.
SMP86xx zxenv (254:0): driver loaded.
squashfs: version 3.4 (2008/08/26) Phillip Lougher
NTFS driver 2.1.28 [Flags: R/O].
fuse init (API version 7.8)
yaffs built Feb 21 2012 10:53:50 Installing.
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
console_peek registed.
tango3dog: Hardware Watchdog Timer for SMP864x/SMP865x 0.1 (def. timeout: 30 sec)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
loop: module loaded
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
tangox_enet0: ethernet mac_core 0 support is disabled from XENV
tangox_enet1: detected phy  at address 0x01
tangox_enet1: Ethernet driver for SMP8xxx internal MAC core 1: 100Mbps Base at 0x26800
tangox_enet1: mac address 00:90:a9:c7:24:51
usbcore: registered new interface driver cdc_ether
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
tangox_bmide: bmide support is disabled
TangoX SATA support is disabled from XENV.
[SMP_NAND] SMP8xxx NAND Driver 0.3 (multi-bits ECC: enabled)
[SMP_NAND]: checking NAND device on CS0 ..
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 3074 at 0x18040000
Bad eraseblock 3197 at 0x18fa0000
[SMP_NAND]: detected NAND on CS0, erasesize 131072, pagesize 2048, oobsize 64, oobavail 2
[SMP_NAND]: checking NAND device on CS1 ..
No NAND device found!!!
[SMP_NAND]: detection completed, load partition information from XENV ..
[SMP_NAND]: load partition information for CS0 ..
Creating 10 MTD partitions on "NAND 512MiB 3,3V 8-bit":
0x00000000-0x00080000 : "bootblocks"
0x00080000-0x00180000 : "yamon"
0x00180000-0x00780000 : "kernel1"
0x00780000-0x00d80000 : "kernel2"
0x00d80000-0x01280000 : "xmat"
0x01280000-0x01c80000 : "imat"
0x01c80000-0x02180000 : "imat_failsafe"
0x02180000-0x0bf80000 : "system"
0x0bf80000-0x1fe00000 : "userdata"
0x1fe00000-0x20000000 : "static_config"
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
TangoX USB initializing...
TangoX USB register base= 0x21700 0 = 0x0
TangoX USB register base= 0x21700 1 = 0x202020
TangoX USB register base= 0x21700 2 = 0x0
TangoX USB register base= 0x21700 3 = 0xf9930
tangox-ehci-hcd-0 tangox-ehci-hcd-0: TangoX USB 2.0
tangox-ehci-hcd-0 tangox-ehci-hcd-0: new USB bus registered, assigned bus number 1
tangox-ehci-hcd-0 tangox-ehci-hcd-0: irq 48, io mem 0xa0021500
tangox-ehci-hcd-0 tangox-ehci-hcd-0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
TangoX USB initializing...
TangoX USB register base= 0x25700 0 = 0x0
TangoX USB register base= 0x25700 1 = 0x202020
TangoX USB register base= 0x25700 2 = 0x0
TangoX USB register base= 0x25700 3 = 0xf9930
tangox-ehci-hcd-1 tangox-ehci-hcd-1: TangoX USB 2.0
tangox-ehci-hcd-1 tangox-ehci-hcd-1: new USB bus registered, assigned bus number 2
tangox-ehci-hcd-1 tangox-ehci-hcd-1: irq 47, io mem 0xa0025500
tangox-ehci-hcd-1 tangox-ehci-hcd-1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb 1-1: new high speed USB device using tangox-ehci-hcd-0 and address 2
No OHCI in SMP8652/SMP8653/SMP8646/SMP8647/SMP8670.
Initializing USB Mass Storage driver...
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.2: new high speed USB device using tangox-ehci-hcd-0 and address 3
usb 1-1.2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Controller 0 is used in different mode.
mice: PS/2 mouse device common for all mice
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Netfilter messages via NETLINK v0.30.
IPv4 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
Freeing unused kernel memory: 2048k freed
==================PRIMARY SYSTEM============================
export SYSCONF_BUILD_DATE=2012.03.26-1742
export SYSCONF_BUILD_VERSION=1.07.18
export SYSCONF_NAND_DRIVER=MTD
export SYSCONF_WDCM_ENABLE=ENABLE
export SYSCONF_FIRMWARE_BIN=wdtvlivegen3.bin
export SYSCONF_FIRMWARE_VER=wdtvlivegen3.ver
export SYSCONF_BOOTLOADER_MTD_PARTITION=/dev/mtdblock1
export SYSCONF_KERNEL_MTD_PARTITION=/dev/mtdblock3
export SYSCONF_FIRMWARE_MTD_PARTITION=/system/rootfs/rootfs.bin
export SYSCONF_FIRMWARE_MTD_SIZE=165675008
export SYSCONF_FIRMWARE_STORAGE_PARTITION=/usrdata/rootfs/pkg.bin
export SYSCONF_STORAGE_PARTITION_SIZE=336068608
export SYSCONF_BOOT_AUTH=y
export SYSCONF_FIRMWARE_FS=squashfs
============================================================

Primary built date: 2012.03.26-1742

MTD / YAFFS should be built in, no need to insmod
SYSCONF_FIRMWARE_MTD_PARTITION = /system/rootfs/rootfs.bin
FW_SIGN = fwup
STORAGE_SIGN =
(0x00) 4 l.alpha.fw_sign 66.61.69.6c. 0x6c696166
Launch mdev for checking firmware in USB storage...
ufsd: module license 'Commercial product' taints kernel.
ufsd: driver 8.5 (Feb 21 2012 11:34:09) LBD=ON with ioctl loaded at c00b4000
NTFS support included
Hfs+/HfsX support included
Built_for__Alfanetworks_wdtv_live_plus_2011-07-13