API tools faq
paste
Advertisement
Guest User

Bootlog DIR-842 C3

a guest
Oct 2nd, 2019
361
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 61.15 KB | None | 0 0
raw download clone embed print report
  1.  
  2.  
  3. U-Boot 1.1.4 (Feb 14 2017 - 10:15:54)
  4.  
  5. SVN revision: 1372
  6. ap152 - Dragonfly 1.0DRAM:
  7. sri
  8. ath_ddr_initial_config(278): (ddr2 init)
  9. ath_sys_frequency: cpu 775 ddr 650 ahb 258
  10. Tap values = (0x10, 0x10, 0x10, 0x10)
  11. 128 MB
  12. Top of RAM usable for U-Boot at: 88000000
  13. Reserving 236k for U-Boot at: 87fc4000
  14. Reserving 192k for malloc() at: 87f94000
  15. Reserving 44 Bytes for Board Info at: 87f93fd4
  16. Reserving 36 Bytes for Global Data at: 87f93fb0
  17. Reserving 128k for boot params() at: 87f73fb0
  18. Stack Pointer at: 87f73f98
  19. Now running in RAM - U-Boot at: 87fc4000
  20. Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
  21. flash size 16MB, sector count = 256
  22. Flash: 16 MB
  23. Power up PLL with outdiv = 0 then switch to 3
  24. In: serial
  25. Out: serial
  26. Err: serial
  27. Net: ath_gmac_enet_initialize...
  28. No valid address in Flash. Using fixed address
  29. ath_gmac_enet_initialize: reset mask:c02200
  30. athr_mgmt_init ::done
  31. Dragonfly ----> S17 PHY *
  32. athrs17_reg_init: complete
  33. SGMII in forced mode
  34. athr_gmac_sgmii_setup SGMII done
  35. : cfg1 0x80000000 cfg2 0x7114
  36. eth0: 00:03:7f:09:0b:ad
  37. eth0 up
  38. eth0
  39. Setting 0x181162c0 to 0x4b962100
  40. Hit any key to stop autoboot: 2  1  0
  41. Reset button released
  42. ## Booting image at 9f080040 ...
  43. Image Name: MIPS Seattle Linux-3.3.8
  44. Created: 2018-05-30 3:35:45 UTC
  45. Image Type: MIPS Linux Multi-File Image (lzma compressed)
  46. Data Size: 1234707 Bytes = 1.2 MB
  47. Load Address: 80060000
  48. Entry Point: 80060000
  49. Contents:
  50. Image 0: 1234699 Bytes = 1.2 MB
  51. Verifying Checksum at 0x9f080080 ...OK
  52. Uncompressing Multi-File Image ... OK
  53. No initrd
  54. ## Transferring control to Linux (at address 80060000) ...
  55. ## Giving linux memsize in bytes, 134217728
  56.  
  57. Starting kernel ...
  58.  
  59. [ 0.000000] Linux version 3.3.8 (rolls@cdWSCMPL03) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #4 Wed May 30 11:00:34 CST 2018
  60. [ 0.000000] bootconsole [early0] enabled
  61. [ 0.000000] CPU revision is: 00019750 (MIPS 74Kc)
  62. [ 0.000000] SoC: Qualcomm Atheros QCA956X rev 0
  63. [ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz
  64. [ 0.000000] Determined physical RAM map:
  65. [ 0.000000] memory: 08000000 @ 00000000 (usable)
  66. [ 0.000000] Initrd not found or empty - disabling initrd
  67. [ 0.000000] Zone PFN ranges:
  68. [ 0.000000] Normal 0x00000000 -> 0x00008000
  69. [ 0.000000] Movable zone start PFN for each node
  70. [ 0.000000] Early memory PFN ranges
  71. [ 0.000000] 0: 0x00000000 -> 0x00008000
  72. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
  73. [ 0.000000] Kernel command line: board=AP152 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(devdata),64k(devconf),64k(misc),15680k(upgrade),64k(art),64k(alpha_boarddata),16m@0(rootfs)ro root=/dev/mtdblock8 init=/sbin/init noinitrd crashkernel=10M@20M
  74. [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
  75. [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  76. [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  77. [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  78. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  79. [ 0.000000] Writing ErrCtl register=00000000
  80. [ 0.000000] Readback ErrCtl register=00000000
  81. [ 0.000000] Memory: 125736k/131072k available (2683k kernel code, 5336k reserved, 668k data, 208k init, 0k highmem)
  82. [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  83. [ 0.000000] NR_IRQS:83
  84. [ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
  85. [ 0.060000] pid_max: default: 32768 minimum: 301
  86. [ 0.060000] Mount-cache hash table entries: 512
  87. [ 0.060000] Performance counters: mips/74K PMU enabled, 4 32-bit counters available to each CPU, irq 13
  88. [ 0.070000] NET: Registered protocol family 16
  89. [ 0.080000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
  90. [ 0.080000] MIPS: machine is Qualcomm Atheros AP152 reference board
  91. [ 0.090000]
  92. [ 0.090000] WLAN firmware dump buffer allocation of 2097152 bytes @ address 0x87a00000- SUCCESS !!!
  93. [ 0.100000] registering PCI controller with io_map_base unset
  94. [ 0.310000] bio: create slab <bio-0> at 0
  95. [ 0.310000] PCI host bridge to bus 0000:00
  96. [ 0.320000] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
  97. [ 0.320000] pci_bus 0000:00: root bus resource [io 0x0001]
  98. [ 0.330000] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
  99. [ 0.330000] pci 0000:00:00.0: using irq 40 for pin 1
  100. [ 0.340000] Switching to clocksource MIPS
  101. [ 0.340000] NET: Registered protocol family 2
  102. [ 0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  103. [ 0.350000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
  104. [ 0.360000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
  105. [ 0.360000] TCP: Hash tables configured (established 4096 bind 4096)
  106. [ 0.370000] TCP reno registered
  107. [ 0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  108. [ 0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  109. [ 0.380000] NET: Registered protocol family 1
  110. [ 0.400000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  111. [ 0.400000] msgmni has been set to 245
  112. [ 0.410000] io scheduler noop registered
  113. [ 0.410000] io scheduler deadline registered (default)
  114. [ 0.530000] HDLC line discipline maxframe=4096
  115. [ 0.530000] N_HDLC line discipline registered.
  116. [ 0.530000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  117. ´Çr™≤ÇÇÇÇÍÅserial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
  118. [ 0.570000] console [ttyS0] enabled, bootconsole disabled
  119. [ 0.570000] console [ttyS0] enabled, bootconsole disabled
  120. [ 0.580000] m25p80 spi0.0: found w25q128, expected m25p80
  121. [ 0.590000] m25p80 spi0.0: w25q128 (16384 Kbytes)
  122. [ 0.590000] 9 cmdlinepart partitions found on MTD device spi0.0
  123. [ 0.600000] spi0.0: the flash image has SEAMA header
  124. [ 0.600000] spi0.0: squashfs filesystem found at offset 0x001b0060
  125. [ 0.610000] Creating 10 MTD partitions on "spi0.0":
  126. [ 0.620000] 0x000000000000-0x000000040000 : "u-boot"
  127. [ 0.620000] 0x000000040000-0x000000050000 : "u-boot-env"
  128. [ 0.630000] 0x000000050000-0x000000060000 : "devdata"
  129. [ 0.640000] 0x000000060000-0x000000070000 : "devconf"
  130. [ 0.640000] 0x000000070000-0x000000080000 : "misc"
  131. [ 0.650000] 0x000000080000-0x000000fd0000 : "upgrade"
  132. [ 0.650000] 0x000000fd0000-0x000000fe0000 : "art"
  133. [ 0.660000] 0x000000fe0000-0x000000ff0000 : "alpha_boarddat"
  134. [ 0.670000] 0x0000001b0060-0x000000b21060 : "rootfs"
  135. [ 0.670000] mtd: partition "rootfs" set to be root filesystem
  136. [ 0.680000] 0x000000000000-0x000001000000 : "flash"
  137. [ 0.690000] m25p80 spi0.1: found pm25lv512, expected m25p80
  138. [ 0.690000] m25p80 spi0.1: pm25lv512 (64 Kbytes)
  139. [ 0.830000] ag71xx_mdio: probed
  140. [ 0.840000] eth0: Atheros AG71xx at 0xb9000000, irq 4
  141. [ 1.420000] eth0: Atheros AR8327 switch driver attached.
  142. [ 4.330000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
  143. [ 4.340000] PPP generic driver version 2.4.2
  144. [ 4.350000] PPP BSD Compression module registered
  145. [ 4.350000] PPP MPPE Compression module registered
  146. [ 4.360000] NET: Registered protocol family 24
  147. [ 4.360000] PPTP driver version 0.8.5
  148. [ 4.370000] u32 classifier
  149. [ 4.370000] Netfilter messages via NETLINK v0.30.
  150. [ 4.370000] nf_conntrack version 0.5.0 (1964 buckets, 7856 max)
  151. [ 4.380000] xt_time: kernel timezone is -0000
  152. [ 4.380000] GRE over IPv4 demultiplexor driver
  153. [ 4.390000] GRE over IPv4 tunneling driver
  154. [ 4.390000] ip_tables: (C) 2000-2006 Netfilter Core Team
  155. [ 4.400000] TCP cubic registered
  156. [ 4.400000] NET: Registered protocol family 10
  157. [ 4.410000] ip6_tables: (C) 2000-2006 Netfilter Core Team
  158. [ 4.420000] IPv6 over IPv4 tunneling driver
  159. [ 4.420000] NET: Registered protocol family 17
  160. [ 4.430000] Ebtables v2.0 registered
  161. [ 4.430000] L2TP core driver, V2.0
  162. [ 4.430000] PPPoL2TP kernel driver, V2.0
  163. [ 4.440000] 8021q: 802.1Q VLAN Support v1.8
  164. [ 4.440000] ### of_selftest(): No testcase data in device tree; not running tests
  165. [ 4.460000] VFS: Mounted root (squashfs filesystem) readonly on device 31:8.
  166. [ 4.460000] Freeing unused kernel memory: 208k freed
  167.  
  168. starting pid 845, tty '': '/etc/init.d/rcS'
  169. [/etc/init.d/S10init.sh]
  170. [/etc/init.d/S15udevd.sh]
  171. [ 5.270000] udevd (856): /proc/856/oom_adj is deprecated, please use /proc/856/oom_score_adj instead.
  172. [/etc/init.d/S16ipv6.sh]
  173. Set DEFAULT policy as DROP.
  174. [/etc/init.d/S19init.sh]
  175. [/etc/init.d/S20init.sh]
  176. DEVCONF: no config data available (ret=-1) !
  177. !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
  178. !! Uable to read device config. !!
  179. !! Setting is reset to factory default. !!
  180. !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
  181. DEFNODE[/etc/defnodes/S11devdata.xml]
  182. DEFNODE[/etc/defnodes/S12devdata.php]
  183. DEFNODE[/etc/defnodes/S13dfs.php]
  184. DEFNODE[/etc/defnodes/S14setchlist.php]
  185. DEFNODE[/etc/defnodes/S20device.xml]
  186. DEFNODE[/etc/defnodes/S22timezone.php]
  187. [/etc/scripts/setdate.sh] 01/01/2000 ...
  188. Sat Jan 1 00:00:08 UTC 2000
  189. DEFNODE[/etc/defnodes/S30device.php]
  190. DEFNODE[/etc/defnodes/S30device.xml]
  191. DEFNODE[/etc/defnodes/S31diagnostic.xml]
  192. DEFNODE[/etc/defnodes/S31locale.php]
  193. DEFNODE[/etc/defnodes/S33wifi.php]
  194. DEFNODE[/etc/defnodes/S40device.xml]
  195. DEFNODE[/etc/defnodes/S80mtfwu.php]
  196. DEFNODE[/etc/defnodes/S90opendns.php]
  197. DEFNODE[/etc/defnodes/S90sessions.php]
  198. DEFNODE[/etc/defnodes/S90sessions_privatekey.php]
  199. DEFNODE[/etc/defnodes/S90upnpigd.php]
  200. DEFNODE[/etc/defnodes/S90upnpwfa.php]
  201. DEFNODE[/etc/defnodes/S91upnpigd2.php]
  202. DEFNODE[/etc/defnodes/S94captcha.php]
  203. SERVD: start service [LOGD]
  204. [/etc/init.d/S20interfaces.sh]
  205. [ 9.080000] ssdk_plat_init start
  206. [ 9.090000] Register QCA PHY driver
  207. [ 9.100000] PHY ID is 0x4dd036
  208. [ 9.200000] qca probe f1 phy driver succeeded!
  209. [ 9.210000] qca-ssdk module init succeeded!
  210. [ 9.270000] fast-classifier: starting up
  211. [ 9.270000] fast-classifier: registered
  212. net.netfilter.nf_conntrack_acct = 1
  213.  
  214. SSDK Init OK![ 9.400000] enable:1
  215. [ 9.400000] bg task init successfull!
  216. [ 9.400000] host_helper_init start
  217. [ 9.420000] /proc/qca_switch/nf_athrs17_hnat is created
  218. [ 9.420000] /proc/qca_switch/nf_athrs17_hnat_wan_type is created
  219. [ 9.430000] /proc/qca_switch/nf_athrs17_hnat_ppp_id is created
  220. [ 9.440000] /proc/qca_switch/nf_athrs17_hnat_udp_thresh is created
  221. [ 9.440000] /proc/qca_switch/nf_athrs17_hnat_wan_ip is created
  222. [ 9.450000] /proc/qca_switch/nf_athrs17_hnat_ppp_peer_ip is created
  223. [ 9.450000] /proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created
  224. [ 9.460000] /proc/qca_switch/nf_athrs17_hnat_wan_mac is created
  225. [ 9.470000] /proc/qca_switch/nf_athrs17_hnat_ppp_id2 is created
  226. [ 9.470000] /proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created
  227. [ 9.480000] /proc/qca_switch/nf_athrs17_hnat_thres_base is created
  228. [ 9.490000] /proc/qca_switch/nf_athrs17_hnat_poll_msec is created
  229. [ 9.490000] /proc/qca_switch/nf_athrs17_hnat_aging_sec is created
  230. [ 9.500000] Registering IPv6 hooks...
  231. [ 9.500000] Adding ACL rules 15 - upnp_ssdp_add_acl_rules
  232. [ 9.540000] ACL is not yet enabled. Enabling...
  233. [ 9.540000] Adding ACL rules 7 - ipv6_snooping_solicted_node_add_acl_rules
  234. [ 9.610000] Adding ACL rules 11 - ipv6_snooping_sextuple0_group_add_acl_rules
  235. [ 9.670000] Adding ACL rules 13 - ipv6_snooping_quintruple0_1_group_add_acl_rules
  236. [ 9.740000] nat wan port is 20
  237. [ 9.740000] Hello, nat helper module for 1.1!
  238.  
  239. operate done.
  240.  
  241. [/etc/init.d/S23udevd.sh]
  242. [/etc/init.d/S45gpiod.sh]
  243. [/etc/init.d/rcS] done!
  244. [/etc/init0.d/S21layout.sh]: start ...
  245. SERVD: start service [LAYOUT]
  246. cat: can't open '/etc/config/langpack': No such file or directory
  247. [/etc/init0.d/S40event.sh]: start ...
  248. [ 10.520000] ADDRCONF(NETDEV_UP): eth0: link is not ready
  249. SERVD: event [SEALPAC.LOAD/default]
  250. [/etc/init0.d/S40gpioevent.sh]: start ...
  251. SEAMA: need meta for searching image.
  252. [/etc/init0.d/S40ttyevent.sh]: start ...
  253. [/etc/init0.d/S41autowan.sh]: start ...
  254. [/etc/init0.d/S41autowanv6.sh]: start ...
  255. SERVD: event [AUTODETECT.REVERT/default]
  256. [/etc/init0.d/S41event.sh]: start ...
  257. [/etc/init0.d/S41factorydefault.sh]: start ...
  258. sh: missing ]
  259. [/etc/init0.d/S41inf.sh]: start ...
  260. [/etc/init0.d/S41smart404.sh]: start ...
  261.  
  262. SSDK Init OK!
  263. operate done.
  264.  
  265.  
  266. SSDK Init OK!
  267. operate done.
  268.  
  269. [ 11.250000] device eth0 entered promiscuous mode
  270. [ 11.260000] ADDRCONF(NETDEV_UP): eth0.1: link is not ready
  271. [ 11.330000] ADDRCONF(NETDEV_UP): eth0.4094: link is not ready
  272. [ 11.390000] device eth0.1 entered promiscuous mode
  273. [ 11.410000] ADDRCONF(NETDEV_UP): br0: link is not ready
  274. SERVD: start service [BRIDGE]
  275. [/etc/init0.d/S42pthrough.sh]: start ...
  276. [/etc/init0.d/S43checkfw.sh]: start ...
  277. [ephp.c read_cond_list 1363] PHP operator precedence issue at: /etc/services/BRIDGE.php, cond_qty: 3, and_qty: 1, or_qty: 1
  278. BRIDGE: The device is not in the bridge mode.
  279. SERVD: start service [LAN]
  280. [ephp.c read_cond_list 1363] PHP operator precedence issue at: /etc/services/LAN.php, cond_qty: 3, and_qty: 1, or_qty: 1
  281. [/etc/init0.d/S44schreboot.sh]: start ...
  282. [/etc/init0.d/S51wlan.sh]: start ...
  283. 377+0 records in
  284. 377+0 records out
  285. [/etc/init0.d/S65ddnsd.sh]: start ...
  286. main: creating usock for control : [/var/run/ddnsd.susock]
  287. [/etc/init0.d/S65logd.sh]: start ...
  288. SERVD: start service [WAN]
  289. [/etc/init0.d/S65user.sh]: start ...
  290. [ephp.c read_cond_list 1363] PHP operator precedence issue at: /etc/services/WAN.php, cond_qty: 3, and_qty: 1, or_qty: 1
  291. [/etc/init0.d/S80mfcd.sh]: start ...
  292. [ 12.340000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  293. [ 12.350000] eth0: link up (1000Mbps/Full duplex)
  294. [ 12.360000] ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
  295. [ 12.370000] br0: port 1(eth0.1) entered forwarding state
  296. [ 12.380000] br0: port 1(eth0.1) entered forwarding state
  297. [ 12.390000] ADDRCONF(NETDEV_CHANGE): eth0.4094: link becomes ready
  298. [ 12.400000] ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
  299. [/etc/init0.d/S80vlan.sh]: start ...
  300. [/etc/init0.d/S88arp.sh]: start ...
  301. run arpmonitor again
  302. [/etc/init0.d/S91proclink.sh]: start ...
  303. [/etc/init0.d/S93cpuload.sh]: start ...
  304. [/etc/init0.d/S95watchdog.sh]: start ...
  305. [/etc/init0.d/rcS] done!
  306.  
  307. Please press Enter to activate this console. SERVD: start service [PHYINF.ETH-1]
  308. SERVD: start service [PHYINF.ETH-2]
  309. SERVD: start service [PHYINF.ETH-3]
  310.  
  311. SSDK Init OK!
  312. operate done.
  313.  
  314.  
  315. SSDK Init OK!
  316. operate done.
  317.  
  318.  
  319. SSDK Init OK!
  320. operate done.
  321.  
  322. SERVD: start service [DEVICE.PASSTHROUGH]
  323. [ 14.040000] device eth0.4094 entered promiscuous mode
  324. [ 14.050000] pppoe pass through (br0<->eth0.4094)
  325. SERVD: start service [IPTABLES]
  326. CONNTRACK_MAX=30000
  327. CONNTRACK_MIN=15000
  328. [ 14.370000] br0: port 1(eth0.1) entered disabled state
  329. SERVD: start service [IP6TABLES]
  330. SERVD: start service [SCH_REBOOT]
  331. SERVD: start service [WIFI.PHYINF]
  332. SERVD: service [WIFI.PHYINF] return error 108.
  333. SERVD: start service [IPTABLES]
  334. SERVD: service [IPTABLES] is already started.
  335. SERVD: start service [IP6TABLES]
  336. SERVD: service [IP6TABLES] is already started.
  337. SERVD: start service [INET.LAN-1]
  338. [/var/servd/INET.LAN-1_start.sh]: starting LAN-1...
  339. SERVD: event [LAN-1.UP/default]
  340. /var/run/phpsh-1960.sh: line 8: can't create /proc/nf_accelerate_to_local: nonexistent directory
  341. SERVD: event [DHCPS4.RESTART/default]
  342. [/var/servd/INET.LAN-1_start.sh]: starting LAN-1 done !!!
  343. SERVD: start service [INET.LAN-2]
  344. [/var/servd/INET.LAN-2_start.sh]: starting LAN-2...
  345. SERVD: event [LAN-2.UP/default]
  346. SERVD: event [DHCPS4.RESTART/default]
  347. [/var/servd/INET.LAN-2_start.sh]: starting LAN-2 done !!!
  348. SERVD: start service [INET.LAN-4]
  349. #!/bin/sh
  350. # No inet profile!!
  351. exit 9
  352.  
  353. SERVD: start service [INET.LAN-5]
  354. #!/bin/sh
  355. # No inet profile!!
  356. exit 9
  357.  
  358. SERVD: start service [INET.LAN-6]
  359. ifsetup: (LAN-6) not active.
  360. SERVD: service [INET.LAN-6] return error 8.
  361. SERVD: start service [INET.LAN-7]
  362. ifsetup: (LAN-7) not active.
  363. SERVD: service [INET.LAN-7] return error 8.
  364. SERVD: start service [INET.LAN-8]
  365. ifsetup: (LAN-8) not active.
  366. SERVD: service [INET.LAN-8] return error 8.
  367. SERVD: start service [IPTMACCTRL]
  368. SERVD: start service [IPTURLCTRL]
  369. SERVD: start service [ACCESSCTRL]
  370. SERVD: start service [IPTPORTT]
  371. SERVD: start service [IP6T.LAN-1]
  372. SERVD: start service [IP6T.LAN-2]
  373. SERVD: start service [IP6T.LAN-3]
  374. SERVD: start service [IP6T.LAN-4]
  375. SERVD: start service [IP6T.LAN-5]
  376. SERVD: start service [PHYINF.WIFI]
  377. SERVD: start service [IP6T.LAN-6]
  378. SERVD: start service [IP6T.LAN-7]
  379. SERVD: service [IP6T.LAN-7] return error 108.
  380. SERVD: stop service [LOGD]
  381. SERVD: start service [LOGD]
  382. SERVD: start service [IP6T.LAN-8]
  383. SERVD: service [IP6T.LAN-8] return error 108.
  384. SERVD: start service [DEVICE.ACCOUNT]
  385. SERVD: start service [IPTABLES]
  386. SERVD: service [IPTABLES] is already started.
  387. SERVD: start service [IP6TABLES]
  388. SERVD: service [IP6TABLES] is already started.
  389. SERVD: start service [INET.WAN-1]
  390. [/var/servd/INET.WAN-1_start.sh]: starting WAN-1...
  391.  
  392. SSDK Init OK!
  393. operate done.
  394.  
  395. [/var/servd/INET.WAN-1_start.sh]: starting WAN-1 done !!!
  396. SERVD: start service [INET.WAN-2]
  397. ifsetup: (WAN-2) not active.
  398. SERVD: service [INET.WAN-2] return error 8.
  399. SERVD: start service [INET.WAN-3]
  400. [/var/servd/INET.WAN-3_start.sh]: starting WAN-3...
  401. WAN-3 a is link local interface.
  402. SERVD: event [WAN-3.UP/default]
  403. [/var/servd/INET.WAN-3_start.sh]: starting WAN-3 done !!!
  404. SERVD: start service [INET.WAN-5]
  405. ifsetup: (WAN-5) not active.
  406. SERVD: service [INET.WAN-5] return error 8.
  407. SERVD: start service [INET.WAN-6]
  408. ifsetup: (WAN-6) not active.
  409. SERVD: service [INET.WAN-6] return error 8.
  410. SERVD: start service [INET.WAN-7]
  411. ifsetup: (WAN-7) not active.
  412. SERVD: service [INET.WAN-7] return error 8.
  413. SERVD: start service [INET.WAN-8]
  414. ifsetup: (WAN-8) not active.
  415. SERVD: service [INET.WAN-8] return error 8.
  416. SERVD: start service [IPTDEFCHAIN]
  417. [ephp.c read_cond_list 1363] PHP operator precedence issue at: /etc/services/IPTDEFCHAIN.php, cond_qty: 3, and_qty: 1, or_qty: 1
  418. [ephp.c read_cond_list 1363] PHP operator precedence issue at: /etc/services/IPTDEFCHAIN.php, cond_qty: 3, and_qty: 1, or_qty: 1
  419. insmod: can't insert '/lib/modules/nf_conntrack_ipsec_pass.ko': No such file or directory
  420. insmod: can't insert '/lib/modules/nf_conntrack_rtsp.ko': No such file or directory
  421. insmod: can't insert '/lib/modules/nf_nat_rtsp.ko': No such file or directory
  422. SERVD: start service [IPTMASQ]
  423. SERVD: start service [IPTVSVR]
  424. SERVD: start service [DEVICE.VLAN]
  425. START.sh:VLAN is disabled
  426. SERVD: start service [IPTPFWD]
  427. SERVD: start service [IPTPORTT]
  428. SERVD: service [IPTPORTT] is already started.
  429. SERVD: start service [IPTDMZ]
  430. SERVD: start service [IPT.WAN-1]
  431. SERVD: start service [IP6T.WAN-1]
  432. SERVD: start service [IPT.WAN-2]
  433. SERVD: start service [IP6T.WAN-2]
  434. SERVD: start service [IPT.WAN-3]
  435. SERVD: start service [IP6T.WAN-3]
  436. SERVD: start service [IPT.WAN-4]
  437. SERVD: start service [IP6T.WAN-4]
  438. SERVD: start service [IPT.WAN-5]
  439. SERVD: service [IPT.WAN-5] return error 108.
  440. SERVD: start service [IP6T.WAN-5]
  441. SERVD: service [IP6T.WAN-5] return error 108.
  442. SERVD: start service [IPT.WAN-6]
  443. SERVD: service [IPT.WAN-6] return error 108.
  444. SERVD: start service [IP6T.WAN-6]
  445. SERVD: service [IP6T.WAN-6] return error 108.
  446. SERVD: start service [IPT.WAN-7]
  447. SERVD: start service [IP6T.WAN-7]
  448. SERVD: service [IP6T.WAN-7] return error 108.
  449. SERVD: start service [IPT.WAN-8]
  450. SERVD: start service [IP6T.WAN-8]
  451. SERVD: service [IP6T.WAN-8] return error 108.
  452. SERVD: stop service [IPT.LAN-1]
  453. SERVD: service [IPT.LAN-1] is already stopped.
  454. SERVD: start service [IPT.LAN-1]
  455. /var/servd/IPT.LAN-1_start.sh: line 4: can't create /proc/fastnat/forskipsupport: nonexistent directory
  456. SERVD: stop service [IPT.LAN-2]
  457. SERVD: service [IPT.LAN-2] is already stopped.
  458. SERVD: start service [IPT.LAN-2]
  459. /var/servd/IPT.LAN-2_start.sh: line 4: can't create /proc/fastnat/forskipsupport: nonexistent directory
  460. SERVD: stop service [IPT.LAN-3]
  461. SERVD: service [IPT.LAN-3] is already stopped.
  462. SERVD: start service [IPT.LAN-3]
  463. SERVD: service [IPT.LAN-3] return error 108.
  464. SERVD: stop service [IPT.LAN-4]
  465. SERVD: service [IPT.LAN-4] is already stopped.
  466. SERVD: start service [IPT.LAN-4]
  467. SERVD: service [IPT.LAN-4] return error 108.
  468. SERVD: stop service [IPT.LAN-5]
  469. SERVD: service [IPT.LAN-5] is already stopped.
  470. SERVD: start service [IPT.LAN-5]
  471. SERVD: service [IPT.LAN-5] return error 108.
  472. SERVD: stop service [IPT.LAN-6]
  473. SERVD: service [IPT.LAN-6] is already stopped.
  474. SERVD: start service [IPT.LAN-6]
  475. SERVD: service [IPT.LAN-6] return error 108.
  476. SERVD: stop service [IPT.LAN-7]
  477. SERVD: service [IPT.LAN-7] is already stopped.
  478. SERVD: start service [IPT.LAN-7]
  479. SERVD: service [IPT.LAN-7] return error 108.
  480. SERVD: stop service [IPT.LAN-8]
  481. SERVD: service [IPT.LAN-8] is already stopped.
  482. SERVD: start service [IPT.LAN-8]
  483. SERVD: service [IPT.LAN-8] return error 108.
  484. SERVD: stop service [SCH_REBOOT_ACTIVE]
  485. SERVD: service [SCH_REBOOT_ACTIVE] is already stopped.
  486. SERVD: stop service [INFSVCS.LAN-1]
  487. SERVD: service [INFSVCS.LAN-1] is already stopped.
  488. SERVD: start service [INFSVCS.LAN-1]
  489. SERVD: event [LAN-1.CONNECTED] not found!
  490. SERVD: event [INFSVCS.LAN-1.UP/default]
  491. SERVD: stop service [INFSVCS.LAN-2]
  492. SERVD: service [INFSVCS.LAN-2] is already stopped.
  493. SERVD: start service [INFSVCS.LAN-2]
  494. SERVD: event [STATUS.READY] not found!
  495. SERVD: event [LAN-2.CONNECTED] not found!
  496. SERVD: event [INFSVCS.LAN-2.UP] not found!
  497. SERVD: stop service [DHCPS4.BRIDGE-1]
  498. SERVD: service [DHCPS4.BRIDGE-1] is already stopped.
  499. SERVD: start service [DHCPS4.BRIDGE-1]
  500. dhcps4setup: (BRIDGE-1) no interface.
  501. SERVD: service [DHCPS4.BRIDGE-1] return error 9.
  502. SERVD: stop service [DHCPS4.LAN-1]
  503. SERVD: service [DHCPS4.LAN-1] is already stopped.
  504. SERVD: start service [DHCPS4.LAN-1]
  505. SERVD: stop service [DHCPS4.LAN-2]
  506. SERVD: service [DHCPS4.LAN-2] is already stopped.
  507. SERVD: start service [DHCPS4.LAN-2]
  508. SERVD: start service [WIFI_MODS]
  509. 377+0 records in
  510. 377+0 records out
  511. 377+0 records in
  512. 377+0 records out
  513. [ 23.430000] mem_manager: module license 'unspecified' taints kernel.
  514. [ 23.430000] Disabling lock debugging due to kernel taint
  515. [ 23.440000] __mm_init_module
  516. [ 23.590000] ath_dfs: Version 2.0.0
  517. [ 23.590000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
  518. [ 23.640000] ath_spectral: Version 2.0.0
  519. [ 23.640000] Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved
  520. [ 24.840000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, PRIVATE_DIAG, WRITE_EEPROM, 11D)
  521. [ 24.850000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
  522. [ 24.890000] ath_tx99: Version 2.0
  523. [ 24.890000] Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved
  524. [ 25.100000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
  525. [ 25.230000] __ath_attach: Set global_scn[0]
  526. [ 25.240000] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead ***
  527. [ 25.250000] ACBKMinfree = 48
  528. [ 25.250000] ACBEMinfree = 32
  529. [ 25.250000] ACVIMinfree = 16
  530. [ 25.260000] ACVOMinfree = 0
  531. [ 25.260000] CABMinfree = 48
  532. [ 25.260000] UAPSDMinfree = 0
  533. [ 25.260000] ATH_TXBUF=2700
  534. [ 25.280000] Enterprise mode: 0x03bda000
  535. [ 25.280000] Restoring Cal data from FS
  536. [ 25.280000]
  537. [ 25.280000] ART Version : -48.0.0
  538. [ 25.290000] SW Image Version : -48.0.0.0.0
  539. [ 25.290000] Board Revision :
  540. [ 25.300000] ar9300_attach: nf_2_nom -110 nf_2_max -60 nf_2_min -125
  541. [ 25.310000] SPECTRAL : get_capability not registered
  542. [ 25.310000] HAL_CAP_PHYDIAG : Capable
  543. [ 25.310000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237)
  544. [ 25.320000] SPECTRAL : get_capability not registered
  545. [ 25.330000] HAL_CAP_RADAR : Capable
  546. [ 25.330000] SPECTRAL : Need to fix the capablity check for SPECTRAL
  547. [ 25.330000] (spectral_attach : 242)
  548. [ 25.340000] SPECTRAL : get_capability not registered
  549. [ 25.350000] HAL_CAP_SPECTRAL_SCAN : Capable
  550. [ 25.350000] SPECTRAL : get_tsf64 not registered
  551. [ 25.360000] spectral_init_netlink 78 NULL SKB
  552. [ 25.360000] SPECTRAL : No ADVANCED SPECTRAL SUPPORT
  553. [ 25.370000] SPECTRAL :----- module attached
  554. [ 25.370000] Green-AP : Green-AP : Attached
  555. [ 25.370000]
  556. [ 25.380000] ath_get_caps[6155] rx chainmask mismatch actual 3 sc_chainmak 0
  557. [ 25.390000] ath_get_caps[6130] tx chainmask mismatch actual 3 sc_chainmak 0
  558. [ 25.400000] band steering initialized for direct attach hardware
  559. [ 25.410000] ieee80211_bsteering_attach: Band steering initialized
  560. [ 25.410000] acfg_attach: 2884: Netlink socket created:8722ba00
  561. [ 25.420000] ath_attach_dfs[12576] dfsdomain 1
  562. [ 25.430000] dfs_attach: event log enabled by default
  563. [ 25.440000] SPECTRAL : module already attached
  564. [ 25.440000] ath_attach: Set global_ic[1]..gloabl_ic ptr:86329130
  565. [ 25.450000] osif_wrap_attach:441 osif wrap attached
  566. [ 25.450000] osif_wrap_devt_init:402 osif wrap dev table init done
  567. [ 25.460000] Wrap Attached: Wrap_com =86d72800 ic->ic_wrap_com=86d72800 &wrap_com->wc_devt=86d72800
  568. [ 25.480000] ath_tx_paprd_init sc 86f68000 PAPRD Enabled
  569. [ 25.490000] wifi0: Atheros 956X: mem=0xb8100000, irq=47
  570. [ 25.500000] ath_da_pci: (Atheros/multi-bss)
  571. [ 26.050000] ath_ol_pci: (Atheros/multi-bss)
  572. [ 26.050000] hif_pci_enable_bus: con_mode = 0x0, device_id = 0x56
  573. [ 26.060000] ath_ol_pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
  574. [ 26.070000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
  575. [ 26.070000] hif_pci_enable_bus: hif_enable_pci done *********** QCA9888 *************hif_pci_enable_bus: hif_type = 0xe, target_type = 0xchif_pci_enable_bus: hif_pci_probe_tgt_wakeup donehif_target_sync: Loop checking FW signalhif_target_sync: Got FW signal, retries = 0hif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_set_hia_extnd: E
  576. [ 26.120000] chip_id 0xc chip_revision 0x0
  577. [ 26.120000]
  578. [ 26.120000] CLOCK PLL skipped
  579. [ 26.130000] hif_set_hia_extnd: setting the target pll frac ffffffff intval ffffffff
  580. [ 26.130000] hif_set_hia_extnd: no frac provided, skipping pre-configuring PLL
  581. [ 26.140000] hif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_pci_configure_legacy_irq: Ehif_pci_configure_legacy_irq: X, ret = 0hif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4
  582. [ 26.170000] hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON
  583. [ 26.180000] __ol_ath_attach() Allocated scn 85e40380
  584. [ 26.190000] __ol_ath_attach: dev name wifi1
  585. [ 26.190000] ol_ath_attach interface_id 1
  586. [ 26.200000] ol_target_init() BMI inited.
  587. [ 26.200000] ol_target_init() BMI Get Target Info.
  588. [ 26.210000] Chip id: 0xc, chip version: 0x1000000
  589. [ 26.210000]
  590. [ 26.210000] CE WAR Disabled
  591. [ 26.220000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
  592. [ 26.220000] ol_target_init() configure Target .
  593. [ 26.230000]
  594. [ 26.230000] Target Version is 1000000
  595. [ 26.230000]
  596. [ 26.230000] Flash Download Address c0000
  597. [ 26.240000] ol_transfer_bin_file: flash data file defined
  598. [ 26.240000] ol_transfer_bin_file[4641] Get Caldata for wifi1.
  599. [ 26.250000] qdf_fs_read[59], Open File /tmp/wifi1.caldata SUCCESS!!file system magic:-2054924042super blocksize:4096inode 4827file size:12064ol_transfer_bin_file: flash cal data len 65535 doesn't equal to 12064
  600. [ 26.270000] ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000
  601. [ 26.280000]
  602. [ 26.280000] Selecting OTP binary for CHIP Version 0
  603. [ 26.340000] ol_transfer_bin_file 4522: downloading file 0, Download data len 9084
  604. [ 26.380000]
  605. [ 26.380000] First OTP send param 10
  606. [ 26.620000] ol_ath_download_firmware :First OTP download and Execute is good address:0x1 return param 4660
  607. [ 26.630000] ol_ath_download_firmware:##Board Id 0 , CHIP Id 0
  608. [ 26.640000] ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000
  609. [ 26.650000] Warning : No board id matched. Selecting default boarddata file
  610. [ 26.650000]
  611. [ 26.650000] wifi1: Selecting board data file name boarddata_0.bin
  612. [ 26.660000]
  613. [ 26.660000] ===find alpha boarddata===
  614. [ 26.670000] qdf_fs_read[59], Open File /lib/firmware/QCA9888/alpha_hw.2/boarddata_0.bin SUCCESS!!file system magic:-2054924042super blocksize:4096inode 2308file size:12064qc98xx_verify_checksum error: flash checksum 0xffff, computed 0xffff
  615. [ 26.690000] ===road alpha boarddata fail, used orignal QCA boarddata===
  616. [ 26.700000] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9888/hw.2/boarddata_0.bin
  617. [ 26.720000] ol_transfer_bin_file 4522: downloading file 3, Download data len 12064
  618. [ 26.720000] QC98XX overwrite boarddate !
  619. [ 26.730000] Board extended Data download address: 0x0
  620. [ 26.760000] ol_ath_download_firmware: Using 0x1234 for the remainder of init
  621. [ 26.760000]
  622. [ 26.760000] Selecting OTP binary for CHIP Version 0
  623. [ 26.780000] ol_transfer_bin_file 4522: downloading file 0, Download data len 9084
  624. [ 26.820000]
  625. [ 26.820000] [Non-Flash] : Ignore Module param
  626. [ 26.830000]
  627. [ 26.830000] Second otp download Param 700
  628. [ 27.090000] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0
  629. [ 27.090000]
  630. [ 27.090000] Mission mode: Firmware CHIP Version 0
  631. [ 27.260000] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144
  632. [ 27.280000] Swap: bytes_left to copy: fw:16; dma_page:28605
  633. [ 27.280000] Swap: wrong length read:0
  634. [ 27.290000] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 233539 Target address 41a4a8
  635. [ 27.300000] scn=85e40380 target_write_addr=41a4a8 seg_info=85f25c10
  636. [ 27.300000] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2
  637. [ 27.310000] bin_filename=QCA9888/hw.2/athwlan.bin swap_filename=/lib/firmware/QCA9888/hw.2/athwlan.codeswap.bin
  638. [ 27.320000] ol_transfer_bin_file: Downloading firmware file: QCA9888/hw.2/athwlan.bin
  639. [ 27.720000] ol_transfer_bin_file 4522: downloading file 1, Download data len 372428
  640. [ 29.150000] ol_target_init() Download FW done.
  641. [ 29.150000] ol_ath_attach() WMI attached. wmi_handle 873a4000
  642. [ 29.160000] wmi_unified_register_event_handler: Event id 62 is unavailable
  643. [ 29.170000] +htc_create .. HIF :85f2c000-htc_create: (0x85fa4800)
  644. [ 29.170000] htc_wmi_init() HT Create . 85fa4800
  645. [ 29.180000] htc_wmi_init 7528 host_enable 0 nss_nwifi_offload 0
  646. [ 29.180000] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko)
  647. [ 29.190000] OL_ACBKMinfree : 0
  648. [ 29.200000] OL_ACBEMinfree : 0
  649. [ 29.200000] OL_ACVIMinfree : 0
  650. [ 29.200000] OL_ACVOMinfree : 0
  651. [ 29.210000] hif_enable_fastpath, Enabling fastpath mode
  652. [ 29.210000] +HWT
  653. [ 29.210000] hif_completion_thread_startup: pipe_num:0 pipe_info:0x85f2f05chif_completion_thread_startup: pipe_num:3 pipe_info:0x85f2f11chif_completion_thread_startup: pipe_num:4 pipe_info:0x85f2f15c
  654. [ 29.240000] -HWT
  655. [ 29.240000] Startup Mode-0 set
  656. [ 29.240000]
  657. [ 29.240000] <=== cfg max peer id 1056 ====>
  658. [ 29.250000] htt_peer_map_timer_init Enter pdev 85158000 hrtimer 8515c8a8
  659. [ 29.260000]
  660. [ 29.260000] htt_alloc_peer_map_mem : Alloc Success : host q vaddr 85e8e000 paddr 5e8e000
  661. [ 29.270000]
  662. [ 29.270000] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts
  663. [ 29.280000] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from 84de0000
  664. [ 29.290000] Firmware_Build_Number:61
  665. [ 29.290000] FW wireless modes: 0x7f9001
  666. [ 29.300000] num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339979fa vht_supp_mcs:0x0000fffa
  667. [ 29.310000] wmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0
  668. [ 29.320000]
  669. [ 29.320000] Sending Ext resource cfg: HOST PLATFORM as 1
  670. [ 29.320000] fw_feature_bitmap as 50 to TGT
  671. [ 29.330000] ol_ath_service_ready_event: tt_support: 1
  672. [ 29.330000] ol_ath_service_ready_event: periodic_chan_stats: 1
  673. [ 29.340000] ol_ath_service_ready_event: sw_cal_support_check_flag: 1
  674. [ 29.350000] Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17
  675. [ 29.360000] idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53
  676. [ 29.360000] ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256,
  677. [ 29.370000] idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53
  678. [ 29.380000] ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024,
  679. [ 29.390000] idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53
  680. [ 29.400000] ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096,
  681. [ 29.400000] idx 0 req 1 num_units 0 num_unit_info 2 unit size 896 actual units 531
  682. [ 29.420000] ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 896,
  683. [ 29.420000] idx 4 req 5 num_units 0 num_unit_info 2 unit size 1948 actual units 531
  684. [ 29.440000] ol_ath_alloc_host_mem_chunk req_id 5 idx 4 num_units 531 unit_len 1948,
  685. [ 29.440000] Support not added yet for Service 91
  686. [ 29.450000] Support not added yet for Service 92
  687. [ 29.450000] No EXT_MSG send INIT now
  688. [ 29.460000] chunk 0 len 13568 requested , ptr 0x5f48000
  689. [ 29.460000] chunk 1 len 54272 requested , ptr 0x4dd0000
  690. [ 29.470000] chunk 2 len 217088 requested , ptr 0x4e40000
  691. [ 29.470000] chunk 3 len 475776 requested , ptr 0x4e80000
  692. [ 29.480000] chunk 4 len 1034388 requested , ptr 0x4f00000
  693. [ 29.490000] ol_ath_service_ready_event[4259] WAPI MBSSID 2
  694. [ 29.530000] Version = 16777216 3 status = 0
  695. [ 29.540000] ol_ath_connect_htc() WMI is ready
  696. [ 29.540000] htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 1
  697. [ 29.550000] target uses HTT version 2.2; host uses 2.2
  698. [ 29.560000] ol_ath_attach() connect HTC.
  699. [ 29.560000] bypasswmi : 0
  700. [ 29.570000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
  701. [ 29.580000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150
  702. [ 29.590000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0
  703. [ 29.590000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0
  704. [ 29.600000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0
  705. [ 29.610000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150
  706. [ 29.620000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080
  707. [ 29.620000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080
  708. [ 29.630000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080
  709. [ 29.640000] Add VHT80 channel: 5210
  710. [ 29.640000] Add VHT80 channel: 5290
  711. [ 29.650000] Add VHT80 channel: 5775
  712. [ 29.650000] Skipping VHT80 channel 5825
  713. [ 29.650000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5210 in case of VHT80+80
  714. [ 29.660000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5290 in case of VHT80+80
  715. [ 29.670000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5210 in case of VHT80+80
  716. [ 29.680000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5290 in case of VHT80+80
  717. [ 29.690000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5210 in case of VHT80+80
  718. [ 29.700000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5290 in case of VHT80+80
  719. [ 29.710000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5210 in case of VHT80+80
  720. [ 29.720000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5775, cfreq2:5290 in case of VHT80+80
  721. [ 29.730000] freq=58
  722. [ 29.730000] OL Resmgr Init-ed
  723. [ 29.730000] ieee80211_bsteering_attach: Band steering initialized
  724. [ 29.740000] acfg_attach: using existing sock 8722ba00
  725. [ 29.740000] SPECTRAL : get_capability not registered
  726. [ 29.750000] HAL_CAP_PHYDIAG : Capable
  727. [ 29.750000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237)
  728. [ 29.760000] SPECTRAL : get_capability not registered
  729. [ 29.770000] HAL_CAP_RADAR : Capable
  730. [ 29.770000] SPECTRAL : Need to fix the capablity check for SPECTRAL
  731. [ 29.770000] (spectral_attach : 242)
  732. [ 29.780000] SPECTRAL : get_capability not registered
  733. [ 29.790000] HAL_CAP_SPECTRAL_SCAN : Capable
  734. [ 29.790000] SPECTRAL : get_tsf64 not registered
  735. [ 29.790000] spectral_init_netlink 78 NULL SKB
  736. [ 29.800000] Green-AP : Green-AP : Attached
  737. [ 29.800000]
  738. [ 29.800000] Green-AP : Attached
  739. [ 29.810000] rate power table override is only supported for AR98XX
  740. [ 29.810000] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna.
  741. [ 29.820000] ol_if_dfs_attach: called; ptr=8481997c, radar_info=861cfb58
  742. [ 29.830000] dfs_attach: event log enabled by default
  743. [ 29.840000] >>>> CB Set (null)
  744. [ 29.840000] ol_ath_attach() UMAC attach .
  745. [ 29.840000]
  746. [ 29.840000] BURSTING enabled by default
  747. [ 29.850000] ol_ath_attach: Set global_ic[2] ..ptr:86329130
  748. [ 29.850000] ath_lowi_if_netlink_init LOWI Netlink successfully created
  749. [ 29.860000] osif_wrap_attach:441 osif wrap attached
  750. [ 29.870000] osif_wrap_devt_init:402 osif wrap dev table init done
  751. [ 29.870000] Wrap Attached: Wrap_com =86e80c00 ic->ic_wrap_com=86e80c00 &wrap_com->wc_devt=86e80c00
  752. [ 29.880000] __ol_ath_attach: needed_headroom reservation 60
  753. [ 29.900000] ol_ath_thermal_mitigation_attach: --
  754. [ 29.900000] ol_ath_pci_probe num_radios=0, wifi_radios[0].sc = 85e40380 wifi_radio_type = 2
  755. [ 29.910000] ath_sysfs_diag_init: diag_fsattr
  756. [ 29.950000] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16
  757. [ 29.960000] +hif_update_pipe_callback pipeid 8
  758. [ 29.960000] -hif_update_pipe_callback
  759. [ 29.980000] __sa_init_module
  760. [ 30.180000] [wifi1] FWLOG: [36583] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 )
  761. [ 30.190000] [wifi1] FWLOG: [36583] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 )
  762. [ 30.200000] [wifi1] FWLOG: [36583] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 )
  763. [ 30.210000] [wifi1] FWLOG: [36583] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 )
  764. [ 30.220000] [wifi1] FWLOG: [36583] WAL_DBGID_TX_AC_BUFFER_SET ( 0x100, 0x11e1a300 )
  765. [ 30.230000] [wifi1] FWLOG: [36786] UNKNOWN 22:55 ( 0x10, 0xa10, 0x110, 0x10, 0x0 )
  766. [ 31.000000] ath_net80211_dfs_clist_update: called, cmd=1, nollist= (null), nentries=0
  767. [ 31.010000] ath_attach_dfs[12576] dfsdomain 1
  768. [ 31.020000] dfs_attach: event log enabled by default
  769. [ 31.040000] isCountryCodeValid: EEPROM regdomain 0x0
  770. [ 31.050000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150
  771. [ 31.060000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0
  772. [ 31.060000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0
  773. [ 31.070000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0
  774. [ 31.080000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150
  775. [ 31.080000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080
  776. [ 31.090000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080
  777. [ 31.100000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080
  778. [ 31.110000] Add VHT80 channel: 5210
  779. [ 31.110000] Add VHT80 channel: 5290
  780. [ 31.110000] Add VHT80 channel: 5530
  781. [ 31.120000] Skipping VHT80 channel 5580
  782. [ 31.120000] Skipping VHT80 channel 5660
  783. [ 31.130000] Skipping VHT80 channel 5680
  784. [ 31.130000] Skipping VHT80 channel 5700
  785. [ 31.130000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5210 in case of VHT80+80
  786. [ 31.140000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5290 in case of VHT80+80
  787. [ 31.150000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5210 in case of VHT80+80
  788. [ 31.160000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5290 in case of VHT80+80
  789. [ 31.170000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5210 in case of VHT80+80
  790. [ 31.180000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5290 in case of VHT80+80
  791. [ 31.190000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5210 in case of VHT80+80
  792. [ 31.200000] EMI WAR rejecting fc1 > fc2 Combination cfreq1:5530, cfreq2:5290 in case of VHT80+80
  793. [ 31.210000] freq=58
  794. [ 31.210000] freq=106
  795. SERVD: start service [PHYINF.BAND24G-1.1]
  796. ifconfig: SIOCGIFFLAGS: No such device
  797. [ 31.410000] wlan_vap_create : enter. devhandle=0x86f70380, opmode=IEEE80211_M_HOSTAP, flags=0x1
  798. [ 31.420000] ieee80211_mbo_vattach:MBO Initialized
  799. [ 31.420000] ieee80211_oce_vattach: OCE Initialized
  800. [ 31.430000] wlan_vap_create : exit. devhandle=0x86f70380, vap=0x860f0000, opmode=IEEE80211_M_HOSTAP, flags=0x1.
  801. [ 31.440000] __ieee80211_smart_ant_init: Smart Antenna is not supported
  802. [ 31.440000] VAP device ath0 created osifp: (85fa7380) os_if: (860f0000)
  803. ath0
  804. Interface doesn't accept private ioctl...
  805. HALDbg (8BE0): Operation not permitted
  806. [ 31.470000] sc nodebug 0
  807. [ 31.540000]
  808. [ 31.540000] DES SSID SET=dlink-3BA0
  809. [ 31.550000] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
  810. [ 31.550000] siwfreq
  811. [ 31.560000] Set freq vap 0 stop send + 860f0000
  812. [ 31.560000] Set freq vap 0 stop send -860f0000
  813. [ 31.600000] Set wait done --860f0000
  814. [ephp.c read_cond_list 1363] PHP operator precedence issue at: /etc/scripts/wifirnodes.php, cond_qty: 3, and_qty: 1, or_qty: 1
  815. SERVD: start service [PHYINF.BAND24G-1.2]
  816. SERVD: service [PHYINF.BAND24G-1.2] return error 8.
  817. SERVD: start service [PHYINF.BAND5G-1.1]
  818. ifconfig: SIOCGIFFLAGS: No such device
  819. [ 32.080000] wlan_vap_create : enter. devhandle=0x85e40380, opmode=IEEE80211_M_HOSTAP, flags=0x1
  820. [ 32.090000] send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 18:0f:76:3d:3b:a3:
  821. [ 32.100000] ieee80211_mbo_vattach:MBO Initialized
  822. [ 32.110000] ieee80211_oce_vattach: OCE Initialized
  823. [ 32.110000] wlan_vap_create : exit. devhandle=0x85e40380, vap=0x84918000, opmode=IEEE80211_M_HOSTAP, flags=0x1.
  824. [ 32.120000] __ieee80211_smart_ant_init: Smart Antenna is not supported
  825. [ 32.130000] Enabling TX checksum bit for the vap ath2 features 4000
  826. [ 32.130000] Enabling SG bit for the vap ath2 features 4000
  827. [ 32.140000] Enabling SG bit for the vap ath2 features 4000
  828. [ 32.150000] Enabling TSO bit for the vap ath2 features 4000
  829. [ 32.150000] Enabling LRO bit for the vap ath2 features 4000
  830. [ 32.160000] VAP device ath2 created osifp: (848e5380) os_if: (84918000)
  831. ath2
  832. [ 32.180000] [wifi1] FWLOG: [38303] UNKNOWN 22:55 ( 0x37, 0x199, 0x130, 0x30, 0x0 )
  833. [ 32.220000]
  834. [ 32.220000] DES SSID SET=dlink-5GHz-3BA0
  835. [ 32.220000] ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
  836. [ 32.230000] siwfreq
  837. [ 32.230000] Set freq vap 0 stop send + 84918000
  838. [ 32.240000] Set freq vap 0 stop send -84918000
  839. [ 32.270000] Set wait done --84918000
  840. [ 32.310000] Resetting spectral chainmask to Rx chainmask
  841. [ephp.c read_cond_list 1363] PHP operator precedence issue at: /etc/scripts/wifirnodes.php, cond_qty: 3, and_qty: 1, or_qty: 1
  842. SERVD: start service [PHYINF.BAND5G-1.2]
  843. [ 32.530000] Switching to Tx Mode-0
  844. SERVD: service [PHYINF.BAND5G-1.2] return error 8.
  845. SERVD: start service [WIFI_ACTIVATE]
  846. [ 33.180000] 8021q: adding VLAN 0 to HW filter on device ath0
  847. [ 33.180000] device ath0 entered promiscuous mode
  848. [ 33.210000] br0: port 2(ath0) entered forwarding state
  849. [ 33.210000] br0: port 2(ath0) entered forwarding state
  850. [ 33.300000] Sending SCAN START cmd
  851. [ 33.300000] 8021q: adding VLAN 0 to HW filter on device ath2
  852. [ 33.310000] device ath2 entered promiscuous mode
  853. [ 33.310000] br0: port 3(ath2) entered forwarding state
  854. [ 33.320000] br0: port 3(ath2) entered forwarding state
  855. SERVD: stop service [WEBACCESS]
  856. SERVD: service [WEBACCESS] is already stopped.
  857. SERVD: start service [WEBACCESS]
  858. killall: fileaccessd: no process killed
  859. /var/servd/WEBACCESS_start.sh: line 3: fileaccessd: not found
  860. SERVD: stop service [SAMBA]
  861. SERVD: service [SAMBA] is already stopped.
  862. SERVD: start service [SAMBA]
  863. SERVD: service [SAMBA] return error 108.
  864. SERVD: stop service [INFSVCS.WAN-3]
  865. SERVD: service [INFSVCS.WAN-3] is already stopped.
  866. SERVD: start service [INFSVCS.WAN-3]
  867. SERVD: event [WAN-3.CONNECTED] not found!
  868. SERVD: event [UPDATERESOLV/default]
  869. SERVD: event [INFSVCS.WAN-3.UP] not found!
  870. SERVD: event [UPNP.IGD.NOTIFY.WANIPCONN1] not found!
  871. SERVD: start service [ENLAN]
  872. [ 34.180000] [wifi1] FWLOG: [40446] WAL channel change freq=5180, mode=0 flags=0 rx_ok=1 tx_ok=1
  873. [ 34.190000] [wifi1] FWLOG: [40760] WAL channel change freq=5200, mode=0 flags=0 rx_ok=1 tx_ok=1
  874. [ 34.200000] [wifi1] FWLOG: [41075] WAL channel change freq=5220, mode=0 flags=0 rx_ok=1 tx_ok=1
  875. [ 35.180000] [wifi1] FWLOG: [41389] WAL channel change freq=5240, mode=0 flags=0 rx_ok=1 tx_ok=1
  876. [ 35.190000] [wifi1] FWLOG: [41703] WAL channel change freq=5260, mode=0 flags=0 rx_ok=1 tx_ok=1
  877. [ 35.200000] [wifi1] FWLOG: [42016] WAL channel change freq=5280, mode=0 flags=0 rx_ok=1 tx_ok=1
  878. [ 35.210000] [wifi1] FWLOG: [42331] WAL channel change freq=5300, mode=0 flags=0 rx_ok=1 tx_ok=1
  879. [ 35.950000] mlme_create_infra_bss : Overriding HT40 channel with HT20 channel
  880. [ 36.010000] __ieee80211_smart_ant_init: Smart Antenna is not supported
  881. [/etc/scripts/upwifistatshlper_G_band.sh] CONNSTATUS ath0 1 ....
  882. not support [CONNSTATUS] ...
  883. [ 36.180000] [wifi1] FWLOG: [42645] WAL channel change freq=5320, mode=0 flags=0 rx_ok=1 tx_ok=1
  884. [ 36.190000] [wifi1] FWLOG: [42958] WAL channel change freq=5500, mode=0 flags=0 rx_ok=1 tx_ok=1
  885. [ 36.200000] [wifi1] FWLOG: [43272] WAL channel change freq=5520, mode=0 flags=0 rx_ok=1 tx_ok=1
  886. [ 37.180000] [wifi1] FWLOG: [43586] WAL channel change freq=5540, mode=0 flags=0 rx_ok=1 tx_ok=1
  887. [ 37.190000] [wifi1] FWLOG: [43901] WAL channel change freq=5560, mode=0 flags=0 rx_ok=1 tx_ok=1
  888. [ 37.200000] [wifi1] FWLOG: [44215] WAL channel change freq=5580, mode=0 flags=0 rx_ok=1 tx_ok=1
  889. [ 38.180000] [wifi1] FWLOG: [44529] WAL channel change freq=5660, mode=0 flags=0 rx_ok=1 tx_ok=1
  890. [ 38.190000] [wifi1] FWLOG: [44843] WAL channel change freq=5680, mode=0 flags=0 rx_ok=1 tx_ok=1
  891. [ 38.200000] [wifi1] FWLOG: [45157] WAL channel change freq=5700, mode=0 flags=0 rx_ok=1 tx_ok=1
  892. [ 38.210000] send_vdev_down_cmd_non_tlv for vap 0 (873a4000)
  893. [ 38.220000] OL vap_start +
  894. [ 38.220000] VDEV START
  895. [ 38.220000] OL vap_start -
  896. [ 38.230000] ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3
  897. [ 38.430000] ol_vdev_start_resp_ev for vap 0 (873a4000)
  898. [ 38.440000] send_wmm_update_cmd_non_tlv:
  899. [ 38.440000] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1
  900. [ 38.450000] send_vdev_up_cmd_non_tlv for vap 0 (873a4000)
  901. [ 38.450000] __ieee80211_smart_ant_init: Smart Antenna is not supported
  902. [/etc/scripts/upwifistatshlper_A_band.sh] CONNSTATUS ath2 1 ....
  903. not support [CONNSTATUS] ...
  904. SERVD: event [IPV6ENABLE/ETH-1]
  905. SERVD: event [IPV6ENABLE/ETH-2]
  906. SERVD: event [IPV6ENABLE/ETH-3]
  907. SERVD: start service [HTTP.LAN-1]
  908. [ 39.200000] [wifi1] FWLOG: [45481] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
  909. [ 39.210000] [wifi1] FWLOG: [45481] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
  910. [ 39.210000] [wifi1] FWLOG: [45486] vap-0 VDEV_MGR_VDEV_START ( 0x143c, 0x2, 0x0, 0x0 )
  911. [ 39.220000] [wifi1] FWLOG: [45487] WAL channel change freq=5180, mode=10 flags=0 rx_ok=1 tx_ok=1
  912. [ 39.230000] [wifi1] FWLOG: [45700] UNKNOWN 14:20 ( 0x0 )
  913. [ 39.240000] [wifi1] FWLOG: [45726] VDEV_MGR_HP_START_TIME ( 0x0, 0x143c, 0x898000 )
  914. [ 39.250000] [wifi1] FWLOG: [45726] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 )
  915. [ 39.250000] [wifi1] FWLOG: [45726] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
  916. [ 39.260000] [wifi1] FWLOG: [45726] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x143c, 0x0, 0x0 )
  917. SERVD: start service [UPNP.LAN-1]
  918. SERVD: event [UPNP.ALIVE.LAN-1/default]
  919. SERVD: start service [NEAP.LAN-1]
  920. SERVD: service [NEAP.LAN-1] return error 108.
  921. SERVD: start service [NAMERESOLV.LAN-1]
  922. SERVD: start service [DHCPS4.LAN-1]
  923. SERVD: service [DHCPS4.LAN-1] is already started.
  924. SERVD: start service [DNS4.LAN-1]
  925. SERVD: stop service [BWC.LAN-1]
  926. SERVD: service [BWC.LAN-1] is already stopped.
  927. SERVD: start service [BWC.LAN-1]
  928. bwc_setup: (LAN-1) bwc node/profile not exist, service stop.
  929. SERVD: service [BWC.LAN-1] return error 8.
  930. SERVD: start service [INET.LAN-3]
  931. [/var/servd/INET.LAN-3_start.sh]: starting LAN-3...
  932. LAN-3 a is link local interface.
  933. SERVD: event [LAN-3.UP/default]
  934. [/var/servd/INET.LAN-3_start.sh]: starting LAN-3 done !!!
  935. SERVD: start service [ENLAN]
  936. SERVD: service [ENLAN] is already started.
  937. SERVD: start service [HTTP.LAN-2]
  938. httpsetup: (LAN-2) not active.
  939. SERVD: service [HTTP.LAN-2] return error 8.
  940. SERVD: start service [DHCPS4.LAN-2]
  941. SERVD: service [DHCPS4.LAN-2] is already started.
  942. SERVD: start service [DNS4.LAN-2]
  943. SERVD: stop service [ROUTE.STATIC]
  944. SERVD: service [ROUTE.STATIC] is already stopped.
  945. SERVD: start service [ROUTE.STATIC]
  946. SERVD: stop service [ROUTE.IPUNNUMBERED]
  947. SERVD: service [ROUTE.IPUNNUMBERED] is already stopped.
  948. SERVD: start service [ROUTE.IPUNNUMBERED]
  949. SERVD: stop service [IPTOBF]
  950. SERVD: service [IPTOBF] is already stopped.
  951. SERVD: start service [IPTOBF]
  952. SERVD: stop service [IPTDEFCHAIN]
  953. SERVD: start service [IPTDEFCHAIN]
  954. [ephp.c read_cond_list 1363] PHP operator precedence issue at: /etc/services/IPTDEFCHAIN.php, cond_qty: 3, and_qty: 1, or_qty: 1
  955. [ephp.c read_cond_list 1363] PHP operator precedence issue at: /etc/services/IPTDEFCHAIN.php, cond_qty: 3, and_qty: 1, or_qty: 1
  956. insmod: can't insert '/lib/modules/nf_conntrack_ipsec_pass.ko': No such file or directory
  957. insmod: can't insert '/lib/modules/nf_conntrack_sip.ko': File exists
  958. insmod: can't insert '/lib/modules/nf_nat_sip.ko': File exists
  959. insmod: can't insert '/lib/modules/nf_conntrack_rtsp.ko': No such file or directory
  960. insmod: can't insert '/lib/modules/nf_nat_rtsp.ko': No such file or directory
  961. insmod: can't insert '/lib/modules/nf_nat_proto_gre.ko': File exists
  962. insmod: can't insert '/lib/modules/nf_conntrack_proto_gre.ko': File exists
  963. insmod: can't insert '/lib/modules/nf_conntrack_pptp.ko': File exists
  964. insmod: can't insert '/lib/modules/nf_nat_pptp.ko': File exists
  965. SERVD: stop service [LLD2]
  966. SERVD: service [LLD2] is already stopped.
  967. SERVD: start service [LLD2]
  968. SERVD: start service [HOSTAPD-PMF]
  969. SERVD: stop service [STUNNEL]
  970. SERVD: service [STUNNEL] is already stopped.
  971. SERVD: start service [STUNNEL]
  972. Configuration file: /var/run/hostapd-ath0.conf
  973. Configuration fi[ 41.930000] ieee80211_ioctl_siwmode: imr.ifm_active=393856, new mode=3, valid=1
  974. le: /var/run/hostapd-ath2.conf
  975. [ 41.940000] br0: port 2(ath0) entered disabled state
  976. [ 41.950000] DEVICE IS DOWN ifname=ath0
  977. ath0: [ 41.950000] DEVICE IS DOWN ifname=ath0
  978. Could not connect to kernel driver
  979. __ERROR [STUNNEL.php] cannot find inf LAN-4
  980. Using interface ath0 with hwaddr 18:0f:76:3d:3b:a0 and ssid "dlink-3BA0"
  981. Start Stunnel service ..
  982. SERVD: stop service [IPT.WAN-1]
  983. [/etc/scripts/upwifistatshlper_G_band.sh] CONNSTATUS ath0 0 ....
  984. not support [CONNSTATUS] ...
  985. SERVD: start service [IPT.WAN-1]
  986. [ 42.560000] Warning: node not in table 0x848e8000
  987. [ 42.690000] br0: port 2(ath0) entered forwarding state
  988. [ 42.690000] br0: port 2(ath0) entered forwarding state
  989. [ 42.700000] 8021q: adding VLAN 0 to HW filter on device ath0
  990. ath0[ 42.700000] ieee80211_ioctl_siwmode: imr.ifm_active=18875008, new mode=3, valid=1
  991. : interface state UNINITIALIZED->ENABLED
  992. ath0: AP-ENABLED
  993. [ 42.750000] STOPPED EVENT for vap 0 (873a4000)
  994. [ 42.750000] send_vdev_down_cmd_non_tlv for vap 0 (873a4000)
  995. [ 42.780000] br0: port 3(ath2) entered disabled state
  996. [ 42.780000] DEVICE IS DOWN ifname=ath2
  997. ath2: [ 42.790000] DEVICE IS DOWN ifname=ath2
  998. Could not connect to kernel driver
  999. Using interface ath2 with hwaddr 18:0f:76:3d:3b:a3 and ssid "dlink-5GHz-3BA0"
  1000. SERVD: start service [HTTP.WAN-3]
  1001. [ 43.190000] [wifi1] FWLOG: [50129] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
  1002. [ 43.190000] [wifi1] FWLOG: [50129] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
  1003. [/etc/scripts/upwifistatshlper_A_band.sh] CONNSTATUS ath2 0 ....
  1004. not support [CONNSTATUS] ...
  1005. httpsetup: (WAN-3) not active.
  1006. SERVD: service [HTTP.WAN-3] return error 8.
  1007. SERVD: start service [INET.WAN-4]
  1008. [ 43.430000] OL vap_start +
  1009. [ 43.430000] VDEV START
  1010. [ 43.430000] OL vap_start -
  1011. [ 43.430000] ol_vdev_start_resp_ev for vap 0 (873a4000)
  1012. [ 43.440000] send_wmm_update_cmd_non_tlv:
  1013. [ 43.440000] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1
  1014. [ 43.450000] send_vdev_up_cmd_non_tlv for vap 0 (873a4000)
  1015. [ 43.460000] __ieee80211_smart_ant_init: Smart Antenna is not supported
  1016. [ 43.460000] ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3
  1017. [ 43.480000] br0: port 3(ath2) entered forwarding state
  1018. [ 43.480000] br0: port 3(ath2) entered forwarding state
  1019. [ 43.490000] 8021q: adding VLAN 0 to HW filter on device ath2
  1020. ath2: interface state UNINITIALIZED->ENABLED
  1021. ath2: AP-ENABLED
  1022. [/var/servd/INET.WAN-4_start.sh]: starting WAN-4...
  1023. [ 43.550000] vap-0(ath2):ieee80211_beacon_update: reinit beacon
  1024. [/var/servd/INET.WAN-4_start.sh]: starting WAN-4 done !!!
  1025. SERVD: stop service [IP6TDEFCHAIN]
  1026. SERVD: service [IP6TDEFCHAIN] is already stopped.
  1027. SERVD: start service [IP6TDEFCHAIN]
  1028. SERVD: stop service [FIREWALL6]
  1029. SERVD: service [FIREWALL6] is already stopped.
  1030. SERVD: start service [FIREWALL6]
  1031. SERVD: stop service [IP6TSMPSECURITY]
  1032. SERVD: service [IP6TSMPSECURITY] is already stopped.
  1033. SERVD: start service [IP6TSMPSECURITY]
  1034. SERVD: stop service [IP6TINGRESSFILTER]
  1035. SERVD: service [IP6TINGRESSFILTER] is already stopped.
  1036. SERVD: start service [IP6TINGRESSFILTER]
  1037. SERVD: service [IP6TINGRESSFILTER] return error 9.
  1038. SERVD: stop service [ROUTE6.DYNAMIC]
  1039. SERVD: service [ROUTE6.DYNAMIC] is already stopped.
  1040. SERVD: start service [ROUTE6.DYNAMIC]
  1041. SERVD: stop service [ROUTE6.STATIC]
  1042. SERVD: service [ROUTE6.STATIC] is already stopped.
  1043. SERVD: start service [ROUTE6.STATIC]
  1044. SERVD: stop service [MULTICAST]
  1045. SERVD: service [MULTICAST] is already stopped.
  1046. SERVD: start service [MULTICAST]
  1047. SERVD: stop service [DEVICE.TIME]
  1048. SERVD: service [DEVICE.TIME] is already stopped.
  1049. SERVD: start service [DEVICE.TIME]
  1050. SERVD: stop service [RIPD]
  1051. SERVD: service [RIPD] is already stopped.
  1052. SERVD: start service [RIPD]
  1053. Run NTP client ...
  1054. [V4] []
  1055. [ 44.190000] [wifi1] FWLOG: [50787] WAL_DBGID_SECURITY_ENCR_EN ( )
  1056. [ 44.190000] [wifi1] FWLOG: [50787] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
  1057. [ 44.200000] [wifi1] FWLOG: [50819] vap-0 VDEV_MGR_VDEV_START ( 0x143c, 0x2, 0x0, 0x0 )
  1058. [ 44.210000] [wifi1] FWLOG: [50819] UNKNOWN 14:20 ( 0x0 )
  1059. [ 44.210000] [wifi1] FWLOG: [50845] VDEV_MGR_HP_START_TIME ( 0x0, 0x143c, 0xd61001 )
  1060. [ 44.220000] [wifi1] FWLOG: [50845] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 )
  1061. [ 44.230000] [wifi1] FWLOG: [50845] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
  1062. [ 44.230000] [wifi1] FWLOG: [50845] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x143c, 0x0, 0x0 )
  1063. SERVD: stop service [EMAIL]
  1064. SERVD: service [EMAIL] is already stopped.
  1065. SERVD: start service [EMAIL]
  1066. ntpclient -h ntp1.dlink.com -i 5 -s -4
  1067. SERVD: stop service [UPNPC]
  1068. SERVD: service [UPNPC] is already stopped.
  1069. SERVD: start service [UPNPC]
  1070. ntp1.dlink.com: Unknown host
  1071. getaddrinfo 2: Connection refused
  1072. getaddrinfo failed: Name or service not knownSERVD: service [UPNPC] return error 108.
  1073. SERVD: stop service [MDNSRESPONDER]
  1074. SERVD: service [MDNSRESPONDER] is already stopped.
  1075. SERVD: start service [MDNSRESPONDER]
  1076. [/etc/scripts/upwifistatshlper_A_band.sh] CONNSTATUS ath2 1 ....
  1077. not support [CONNSTATUS] ...
  1078. NTP4 will run in 10 seconds!
  1079. mdnsresponder server start !
  1080. SERVD: stop service [NAMERESOLV]
  1081. SERVD: service [NAMERESOLV] is already stopped.
  1082. SERVD: start service [NAMERESOLV]
  1083. SERVD: stop service [INFSVCS.LAN-3]
  1084. SERVD: service [INFSVCS.LAN-3] is already stopped.
  1085. SERVD: start service [INFSVCS.LAN-3]
  1086. [ 45.420000] mlme_create_infra_bss : Overriding HT40 channel with HT20 channel
  1087. [ 45.460000] __ieee80211_smart_ant_init: Smart Antenna is not supported
  1088. [ 45.550000] vap-0(ath0):ieee80211_beacon_update: reinit beacon
  1089. SERVD: event [LAN-3.CONNECTED] not found!
  1090. SERVD: event [INFSVCS.LAN-3.UP] not found!
  1091. SERVD: stop service [DNS]
  1092. SERVD: service [DNS] is already stopped.
  1093. SERVD: start service [DNS]
  1094. SERVD: start service [PHYINF.BAND5G-1.1_ACTIVE]
  1095. SERVD: event [WLAN.CONNECTED/default]
  1096. SERVD: start service [PHYINF.BAND24G-1.1_ACTIVE]
  1097. WLAN 24G LED:TURN_ON!
  1098. SERVD: event [WLAN.CONNECTED/default]
  1099. SERVD: stop service [HTTP]
  1100. SERVD: service [HTTP] is already stopped.
  1101. SERVD: start service [HTTP]
  1102. [/etc/scripts/upwifistatshlper_G_band.sh] CONNSTATUS ath0 1 ....
  1103. not support [CONNSTATUS] ...
  1104. WLAN 24G LED:TURN_ON!
  1105. SERVD: event [HTTP.UP] not found!
  1106. SERVD: stop service [IPT.WAN-3]
  1107. SERVD: start service [IPT.WAN-3]
  1108. SERVD: stop service [IP6TFIREWALL]
  1109. SERVD: service [IP6TFIREWALL] is already stopped.
  1110. SERVD: start service [IP6TFIREWALL]
  1111. SERVD: stop service [IP6T.WAN-1]
  1112. SERVD: start service [IP6T.WAN-1]
  1113. SERVD: stop service [IP6T.WAN-2]
  1114. SERVD: start service [IP6T.WAN-2]
  1115. SERVD: stop service [IP6T.WAN-3]
  1116. SERVD: start service [IP6T.WAN-3]
  1117. SERVD: stop service [IP6T.WAN-4]
  1118. SERVD: start service [IP6T.WAN-4]
  1119. SERVD: stop service [IP6T.WAN-5]
  1120. SERVD: service [IP6T.WAN-5] is already stopped.
  1121. SERVD: start service [IP6T.WAN-5]
  1122. SERVD: service [IP6T.WAN-5] return error 108.
  1123. SERVD: stop service [IP6T.WAN-6]
  1124. SERVD: service [IP6T.WAN-6] is already stopped.
  1125. SERVD: start service [IP6T.WAN-6]
  1126. SERVD: service [IP6T.WAN-6] return error 108.
  1127. SERVD: stop service [IP6T.WAN-7]
  1128. SERVD: service [IP6T.WAN-7] is already stopped.
  1129. SERVD: start service [IP6T.WAN-7]
  1130. SERVD: service [IP6T.WAN-7] return error 108.
  1131. SERVD: stop service [IP6T.WAN-8]
  1132. SERVD: service [IP6T.WAN-8] is already stopped.
  1133. SERVD: start service [IP6T.WAN-8]
  1134. SERVD: service [IP6T.WAN-8] return error 108.
  1135. SERVD: stop service [IP6T.LAN-1]
  1136. SERVD: start service [IP6T.LAN-1]
  1137. SERVD: stop service [IP6T.LAN-2]
  1138. SERVD: start service [IP6T.LAN-2]
  1139. SERVD: stop service [IP6T.LAN-3]
  1140. SERVD: start service [IP6T.LAN-3]
  1141. SERVD: stop service [IP6T.LAN-4]
  1142. SERVD: start service [IP6T.LAN-4]
  1143. SERVD: stop service [IP6T.LAN-5]
  1144. SERVD: start service [IP6T.LAN-5]
  1145. SERVD: stop service [IP6T.LAN-6]
  1146. SERVD: start service [IP6T.LAN-6]
  1147. SERVD: stop service [IP6T.LAN-7]
  1148. SERVD: service [IP6T.LAN-7] is already stopped.
  1149. SERVD: start service [IP6T.LAN-7]
  1150. SERVD: service [IP6T.LAN-7] return error 108.
  1151. SERVD: stop service [IP6T.LAN-8]
  1152. SERVD: service [IP6T.LAN-8] is already stopped.
  1153. SERVD: start service [IP6T.LAN-8]
  1154. SERVD: service [IP6T.LAN-8] return error 108.
  1155. SERVD: start service [LOG.EMAIL]
  1156. SERVD: start service [ENLAN]
  1157. SERVD: service [ENLAN] is already started.
  1158. SERVD: start service [HTTP.LAN-3]
  1159. SERVD: start service [UPNP.LAN-3]
  1160. SERVD: event [UPNP.ALIVE.LAN-3/default]
  1161. SERVD: start service [NAMERESOLV.LAN-3]
  1162. SERVD: stop service [STUNNEL]
  1163. Stop Stunnel service ..
  1164. SERVD: start service [STUNNEL]
  1165. __ERROR [STUNNEL.php] cannot find inf LAN-4
  1166. Start Stunnel service ..
  1167. SERVD: stop service [ROUTE6.STATIC]
  1168. SERVD: start service [ROUTE6.STATIC]
  1169. SERVD: stop service [ROUTE6.DYNAMIC]
  1170. SERVD: start service [ROUTE6.DYNAMIC]
  1171. SERVD: stop service [IP6TSMPSECURITY]
  1172. SERVD: start service [IP6TSMPSECURITY]
  1173. SERVD: stop service [IP6TINGRESSFILTER]
  1174. SERVD: service [IP6TINGRESSFILTER] is already stopped.
  1175. SERVD: start service [IP6TINGRESSFILTER]
  1176. SERVD: service [IP6TINGRESSFILTER] return error 9.
  1177. SERVD: stop service [IP6TOBF]
  1178. SERVD: service [IP6TOBF] is already stopped.
  1179. SERVD: start service [IP6TOBF]
  1180. SERVD: stop service [IP6TDEFCHAIN]
  1181. SERVD: start service [IP6TDEFCHAIN]
  1182. SERVD: stop service [RIPD]
  1183. SERVD: start service [RIPD]
  1184. SERVD: stop service [LLD2]
  1185. SERVD: start service [LLD2]
  1186. SERVD: stop service [HTTP]
  1187. SERVD: event [HTTP.DOWN] not found!
  1188. SERVD: start service [HTTP]
  1189. startup_server:IPV6, is multicast
  1190. SERVD: event [HTTP.UP] not found!
  1191. SERVD: stop service [NAMERESOLV]
  1192. SERVD: start service [NAMERESOLV]
  1193. SERVD: start service [HTTP]
  1194. SERVD: service [HTTP] is already started.
  1195. Run NTP client ...
  1196. [V6] []
  1197. ntpclient -h ntp1.dlink.com -i 5 -s -4
  1198. NTP4 will run in 10 seconds!
  1199. Run NTP client ...
  1200. [V6] []
  1201. ntpclient -h ntp1.dlink.com -i 5 -s -4
  1202. NTP4 will run in 10 seconds!
  1203. Run NTP client ...
  1204. [V6] []
  1205. ntpclient -h ntp1.dlink.com -i 5 -s -4
  1206. NTP4 will run in 10 seconds!
  1207. Run NTP client ...
  1208. [V6] []
  1209. ntpclient -h ntp1.dlink.com -i 5 -s -4
  1210. NTP4 will run in 10 seconds!
  1211. SERVD: event [AUTODETECT/default]
  1212. Autoconfigure Mode without 6RD
  1213. [ephp.c read_cond_list 1363] PHP operator precedence issue at: /etc/services/WAN.php, cond_qty: 3, and_qty: 1, or_qty: 1
  1214. Run NTP client ...
  1215. [V6] []
  1216. ntpclient -h ntp1.dlink.com -i 5 -s -4
  1217. NTP4 will run in 10 seconds!
  1218. Run NTP client ...
  1219. [V6] []
  1220. ntpclient -h ntp1.dlink.com -i 5 -s -4
  1221. NTP4 will run in 10 seconds!
  1222. Run NTP client ...
  1223. [V6] []
  1224. ntpclient -h ntp1.dlink.com -i 5 -s -4
  1225. NTP4 will run in 10 seconds!
  1226. Run NTP client ...
  1227. [V6] []
  1228. ntpclient -h ntp1.dlink.com -i 5 -s -4
  1229. NTP4 will run in 10 seconds!
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!