-----------------------------------------------------------
   Samsung Primitive Bootloader (PBL) v3.0
   Copyright (C) Samsung Electronics Co., Ltd. 2006-2010
-----------------------------------------------------------

+n1stVPN       2688
+nPgsPerBlk    64
PBL found bootable SBL: Partition(3).

Set cpu clk. from 400MHz to 800MHz.
OM=0x9, device=OnenandMux(Audi)
IROM e-fused - Non Secure Boot Version.

-----------------------------------------------------------
   Samsung Secondary Bootloader (SBL) v3.0
   Copyright (C) Samsung Electronics Co., Ltd. 2006-2010

   Board Name: ARIES REV 03
   Build On: Dec 29 2011 16:57:09
-----------------------------------------------------------

Re_partition: magic code(0x0)
[PAM:   ] ++FSR_PAM_Init
[PAM:   ]   OneNAND physical base address       : 0xb0000000
[PAM:   ]   OneNAND virtual  base address       : 0xb0000000
[PAM:   ]   OneNAND nMID=0xec : nDID=0x50
[PAM:   ] --FSR_PAM_Init
fsr_bml_load_partition: pi->nNumOfPartEntry = 12
partitions loading success
board partition information update.. source: 0x0
.Done.
read 1 units.
==== PARTITION INFORMATION ====
 ID         : IBL+PBL (0x0)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 0
 NO_UNITS   : 1
===============================
 ID         : PIT (0x1)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 1
 NO_UNITS   : 1
===============================
 ID         : EFS (0x14)
 ATTR       : RW STL SLC (0x1101)
 FIRST_UNIT : 2
 NO_UNITS   : 40
===============================
 ID         : SBL (0x3)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 42
 NO_UNITS   : 5
===============================
 ID         : SBL2 (0x4)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 47
 NO_UNITS   : 5
===============================
 ID         : PARAM (0x15)
 ATTR       : RW STL SLC (0x1101)
 FIRST_UNIT : 52
 NO_UNITS   : 20
===============================
 ID         : KERNEL (0x6)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 72
 NO_UNITS   : 30
===============================
 ID         : RECOVERY (0x7)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 102
 NO_UNITS   : 30
===============================
 ID         : FACTORYFS (0x16)
 ATTR       : RW STL SLC (0x1101)
 FIRST_UNIT : 132
 NO_UNITS   : 1146
===============================
 ID         : DBDATAFS (0x17)
 ATTR       : RW STL SLC (0x1101)
 FIRST_UNIT : 1278
 NO_UNITS   : 536
===============================
 ID         : CACHE (0x18)
 ATTR       : RW STL SLC (0x1101)
 FIRST_UNIT : 1814
 NO_UNITS   : 140
===============================
 ID         : MODEM (0xb)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 1954
 NO_UNITS   : 50
===============================
loke_init: j4fs_open success..
load_lfs_parameters valid magic code and version.
load_debug_level reading debug level from file successfully(0x574f4c44).
init_fuel_gauge: vcell = 3805mV, soc = 56
reading nps status file is successfully!.
nps status=0x504d4f43
PMIC_IRQ1    = 0x20
PMIC_IRQ2    = 0x0
PMIC_IRQ3    = 0x0
PMIC_IRQ4    = 0x0
PMIC_STATUS1 = 0x40
PMIC_STATUS2 = 0x0
get_debug_level current debug level is 0x574f4c44.
aries_process_platform: Debug Level Low
keypad_scan: key value ----------------->= 0x0
CONFIG_ARIES_REV:48 , CONFIG_ARIES_REV03:48
aries_process_platform: final s1 booting mode = 0
DISPLAY_PATH_SEL[MDNIE 0x1]is on
MDNIE setting Init start!!
vsync interrupt is off
video interrupt is off
[fb0] turn on
MDNIE setting Init end!!

Autoboot (0 seconds) in progress, press any key to stop
get_debug_level current debug level is 0x574f4c44.
get_debug_level current debug level is 0x574f4c44.
boot_kernel: Debug Level Low
FOTA Check Bit
 Read BML page=, NumPgs=
FOTA Check Bit (0xffffffff)
Load Partion idx = (6)
..............................done
Kernel read success from kernel partition no.6, idx.6.
setting param.serialnr=0x343380cf 0x4fda00ec
setting param.board_rev=0x30
setting param.cmdline=console=ttySAC2,115200 loglevel=4

Starting kernel at 0x32000000...