PM_RSTS: 0x00001000
RPi: BOOTLOADER release VERSION:c3f26b60 DATE: Dec 11 2020 TIME: 11:15:20 BOOTMODE: 0x00000006 part: 0 BUILD_TIMESTAMP=1607685317 0xdaaa69e8 0x00c03130 0x000c27e6
PM_RSTS: 0x00001000
part 00000000 reset_info 00000000
uSD voltage 3.3V
Initialising SDRAM 'Samsung' 16Gb x2 total-size: 32 Gbit 3200
PCI reset
PCI reset
VLI: HUB2: 0xfff00000 0x24e6 MCU: 0xfff20000 0x15218
XHCI-STOP
xHC ver: 256 HCS: 05000420 fc000031 00e70004 HCC: 002841eb
xHC ver: 256 HCS: 05000420 fc000031 00e70004 HCC: 002841eb
xHC ports 5 slots 32 intrs 4
Boot mode: SD (01) order 524
SD HOST: 250000000 CTL0: 0x00000000 BUS: 100000 Hz actual: 100000 HZ div: 2500 (1250) status: 0x1fff0000 delay: 1080
SD HOST: 250000000 CTL0: 0x00000f00 BUS: 100000 Hz actual: 100000 HZ div: 2500 (1250) status: 0x1fff0000 delay: 1080
CID: 0002544d5341303247092b62d0be00c6
CSD: 002e00325b5aa3b4ffffff800a800000
SD: bus-width: 4 spec: 2 SCR: 0x02258000 0x01000000
SD HOST: 250000000 CTL0: 0x00000f00 BUS: 12500000 Hz actual: 12500000 HZ div: 20 (10) status: 0x1fff0000 delay: 8
MBR: 0x00000800,   65536 type: 0x0c
MBR: 0x00000001,    2047 type: 0xee
MBR: 0x00000000,       0 type: 0x00
MBR: 0x00000000,       0 type: 0x00
Trying partition: 0
lba: 2048 oem: 'mkfs.fat' volume: '  V       ^ '
rsc 32 fat-sectors 254 c-count 64964 c-size 1 r-dir 1 r-sec 32
PM_RSTS: 0x00001000
Trying partition: 0
lba: 2048 oem: 'mkfs.fat' volume: '  V       ^ '
rsc 32 fat-sectors 254 c-count 64964 c-size 1 r-dir 1 r-sec 32
Read config.txt bytes      181 hnd 0x0000b18b sha256 d46fa6e6fddf8580
Read start4.elf bytes  2213312 hnd 0x000017a6 sha256 19bbfbc3ec1da69d
Read fixup4.dat bytes     5428 hnd 0x000000d7 sha256 5481e23d9a139ecb
0x00c03130 0x00000000 0x0000003f
MEM GPU: 76 ARM: 948 TOTAL: 1024
Starting start4.elf @ 0xfec00200 partition 0
PCI reset
+


Tow-Boot 2021.04 (Apr 05 2021 - 15:03:29 +0000)002-pre

DRAM:  3.9 GiB
RPI 400 (0xc03130)
MMC:   mmcnr@7e300000: 1, emmc2@7e340000: 0
Loading Environment from FAT... *** Warning - bad CRC, using default environment

Error: malloc in gunzip failed!
There is no valid bmp file at the given address
In:    serial
Out:   vidconsole
Err:   vidconsole
Net:   eth0: ethernet@7d580000
PCIe BRCM: link up, 5.0 Gbps x1 (SSC)
starting USB...
Bus xhci_pci: probe failed, error -110
No working controllers found
Error: malloc in gunzip failed!
There is no valid bmp file at the given address
                                                                                                                  Please press [ESCAPE] or [CTRL+C] to enter the boot menu.

switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
"Synchronous Abort" handler, esr 0x96000004
elr: 00000000000a46b4 lr : 00000000000a46ec (reloc)
elr: 000000003b3706b4 lr : 000000003b3706ec