McBin, boot from SD

[SWITCH PINS ON SW1 and SW2 to 'boot from SD' and reset with the slot being empty]

Marvell>> reset
resetting ...

BootROM - 2.03
Starting CP-0 IOROM 1.07
Booting from SD 0 (0x29)
SD - wait_for_sd_interrupt: Error interrupt -  00008000
SD - wait_for_sd_interrupt: Error interrupt status 00000001
SD - sd_cmd8_send_if_cond: no response, identified as legacy card!
SD - wait_for_sd_interrupt: Command timeout.

SD - sd_get_cmd_response: Get command response failed.

SD - sd_acmd41_send_op_cond: Failed - ret = 00000082
SD - sd_init: invalid OCR!
Error: Failed initializing interface
Error: Failed boot attempt 01. error = 0x0C3

BootROM - 2.03
Starting CP-0 IOROM 1.07
Booting from SD 0 (0x29)
SD - wait_for_sd_interrupt: Error interrupt -  00008000
SD - wait_for_sd_interrupt: Error interrupt status 00000003
SD - sd_get_cmd_response: Get command response failed.

SD - sd_init: Failed - ret = 00000081
Error: Failed initializing interface
sponse: Get command response failed.

SD - sd_acmd41_send_op_cond: Failed - ret = 00000082
SD - sd_init: invalid OCR!
Error: Failed initializing interface
Error: Failed boot attempt 02. error = 0x0C1

BootROM - 2.03
Starting CP-0 IOROM 1.07
Booting from SD 0 (0x29)
SD - wait_for_sd_interrupt: Error interrupt -  00008000
SD - wait_for_sd_interrupt: Error interrupt status 00000001
SD - sd_cmd8_send_if_cond: no response, identified as legacy card!
SD - wait_for_sd_interrupt: Command timeout.

SD - sd_get_cmd_response: Get command response failed.

SD - sd_acmd41_send_op_cond: Failed - ret = 00000082
SD - sd_init: invalid OCR!
Error: Failed initializing interface
Error: Failed boot attempt 03. error = 0x0C3

BootROM - 2.03
Starting CP-0 IOROM 1.07
Booting from SD 0 (0x29)
SD - wait_for_sd_interrupt: Error interrupt -  00008000
SD - wait_for_sd_interrupt: Error interrupt status 00000003
SD - sd_get_cmd_response: Get command response failed.

SD - sd_init: Failed - ret = 00000081
Error: Failed initializing interface
sponse: Get command response failed.

SD - sd_acmd41_send_op_cond: Failed - ret = 00000082
SD - sd_init: invalid OCR!
Error: Failed initializing interface
Error: Failed boot attempt 04. error = 0x0C1

Trying Uart..

[PLUG prepared SD card and reset]

BootROM - 2.03
Starting CP-0 IOROM 1.07
Booting from SD 0 (0x29)
Found valid image at boot postion 0x002
lNOTICE:  Starting binary extension
NOTICE:  Gathering DRAM information
mv_ddr: mv_ddr-devel-17.06.0-ga55312d (May 24 2017 - 14:13:07)
mv_ddr: completed successfully
NOTICE:  Booting Trusted Firmware
NOTICE:  BL1: v1.3(release):devel-17.06.0:12348f6
NOTICE:  BL1: Built : 14:13:21, May 24 2017
NOTICE:  BL1: Booting BL2
lNOTICE:  BL2: v1.3(release):devel-17.06.0:12348f6
NOTICE:  BL2: Built : 14:13:24, May 24 2017
NOTICE:  BL1: Booting BL31
lNOTICE:  BL31: v1.3(release):devel-17.06.0:12348f6
NOTICE:  BL31: Built : 14:13:32, May 24 2017
l

U-Boot 2015.01-armada-17.06.1-01623-g0372ea6 (May 29 2017 - 19:46:30)

I2C:   ready
DRAM:  3.8 GiB
Board: MACCHIATOBin-8040
Clock:  CPU     1300 [MHz]
	DDR     800  [MHz]
	FABRIC  800  [MHz]
	MSS     200  [MHz]
	DDR 64 Bit width
	LLC Enabled (Exclusive Mode)
Comphy chip #0:
Comphy-0: PEX0
Comphy-1: PEX0
Comphy-2: PEX0
Comphy-3: PEX0
Comphy-4: SFI
Comphy-5: SATA1
Comphy chip #1:
Comphy-0: SGMII1        1.25 Gbps
Comphy-1: SATA0
Comphy-2: USB3_HOST0
Comphy-3: SATA1
Comphy-4: SFI
Comphy-5: SGMII2        3.125 Gbps

ERROR: UTMI PHY port type is invalid

at drivers/phy/comphy_cp110.c:1707/comphy_dedicated_phys_init()

ERROR: UTMI PHY port type is invalid

at drivers/phy/comphy_cp110.c:1707/comphy_dedicated_phys_init()

ERROR: UTMI PHY port type is invalid

at drivers/phy/comphy_cp110.c:1707/comphy_dedicated_phys_init()
UTMI PHY 0 initialized to USB Host255
UTMI PHY 1 initialized to USB Host255
UTMI PHY 2 initialized to USB Host255
Now running in RAM - U-Boot at: 3ff0a000
U-Boot DT blob at : 000000003f9f4548
NAND:  0 MiB
MMC:   XENON-SDHCI: 0, XENON-SDHCI: 1
Card did not respond to voltage select!
mmc_init: -17, time 19
MMC init failed
Using default environment

PCIE-0: Link up (Gen1-x1, Bus0)
SCSI:  SATA link 0 timeout.
Target spinup took 0 ms.
AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
flags: 64bit ncq led only pmp fbss pio slum part sxs
Target spinup took 0 ms.
Target spinup took 0 ms.
AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
flags: 64bit ncq led only pmp fbss pio slum part sxs
No Link on this port!
Can not start port 0
Net:   e1000: 00:1b:21:28:bc:b2
       Skipping disabled port egiga1
Skipping disabled port egiga2
e1000#0
Warning: e1000#0 MAC addresses don't match:
Address in SROM is         00:1b:21:28:bc:b2
Address in environment is  00:00:00:00:51:81
, egiga0 [PRIME]
Warning: egiga0 MAC addresses don't match:
Address in SROM is         00:00:00:00:51:81
Address in environment is  00:00:00:00:51:82
, egiga1
Warning: egiga1 MAC addresses don't match:
Address in SROM is         00:00:00:00:51:81
Address in environment is  00:00:00:00:51:83
, egiga2
Warning: egiga2 using MAC address from net device
, egiga3
Error: egiga3 address not set.

Hit any key to stop autoboot:  0
Marvell>>