vs_output

> Executing task: pio run <

Processing STM32F103RC_btt (platform: ststm32@~6.1; board: genericSTM32F103RC; framework: arduino)
---------------------------------------------------------------------------------
Verbose mode can be enabled via `-v, --verbose` option
CONFIGURATION: https://docs.platformio.org/page/boards/ststm32/genericSTM32F103RC.html
PLATFORM: ST STM32 (6.1.1) > STM32F103RC (48k RAM. 256k Flash)
HARDWARE: STM32F103RCT6 72MHz, 48KB RAM, 256KB Flash
DEBUG: Current (blackmagic) External (blackmagic, jlink, stlink)
PACKAGES:
 - framework-arduinoststm32-maple 2.10000.200103 (1.0.0)
 - tool-stm32duino 1.0.1
 - toolchain-gccarmnoneeabi 1.70201.0 (7.2.1)
Converting Marlin.ino
LDF: Library Dependency Finder -> http://bit.ly/configure-pio-ldf
LDF Modes: Finder ~ chain, Compatibility ~ soft
Found 31 compatible libraries
Scanning dependencies...
Dependency Graph
|-- <SoftwareSerialM> 1.0.0
|-- <TMCStepper> 0.7.1
|   |-- <SoftwareSerialM> 1.0.0
|-- <U8glib-HAL> 0.4.3
|   |-- <Wire> 1.0
|-- <STM32ADC> 1.0
|-- <EEPROM>
|-- <USBComposite for STM32F1> 0.91
|-- <Wire> 1.0
|-- <FreeRTOS701>
|-- <Servo(STM32F1)> 1.1.2
Building in release mode
Compiling .pio/build/STM32F103RC_btt/src/src/HAL/STM32F1/HAL.cpp.o
Compiling .pio/build/STM32F103RC_btt/src/src/HAL/STM32F1/HAL_SPI.cpp.o
Compiling .pio/build/STM32F103RC_btt/src/src/HAL/STM32F1/MarlinSerial.cpp.o
Compiling .pio/build/STM32F103RC_btt/src/src/HAL/STM32F1/SPI.cpp.o
In file included from Marlin/src/HAL/STM32F1/../../inc/MarlinConfig.h:49:0,
                 from Marlin/src/HAL/STM32F1/HAL.cpp:30:
Marlin/src/HAL/STM32F1/../../inc/SanityCheck.h:782:6: error: #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination"
     #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination"
      ^~~~~
Marlin/src/HAL/STM32F1/../../inc/SanityCheck.h:851:6: error: #error "FILAMENT_CHANGE_UNLOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
     #error "FILAMENT_CHANGE_UNLOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
      ^~~~~
Marlin/src/HAL/STM32F1/../../inc/SanityCheck.h:1400:4: error: #error "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL."
   #error "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL."
    ^~~~~
In file included from Marlin/src/HAL/STM32F1/../../inc/MarlinConfig.h:49:0,
                 from Marlin/src/HAL/STM32F1/HAL_SPI.cpp:32:
Marlin/src/HAL/STM32F1/../../inc/SanityCheck.h:782:6: error: #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination"
     #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination"
      ^~~~~
Marlin/src/HAL/STM32F1/../../inc/SanityCheck.h:851:6: error: #error "FILAMENT_CHANGE_UNLOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
     #error "FILAMENT_CHANGE_UNLOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
      ^~~~~
Marlin/src/HAL/STM32F1/../../inc/SanityCheck.h:1400:4: error: #error "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL."
   #error "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL."
    ^~~~~
In file included from Marlin/src/HAL/STM32F1/../../inc/MarlinConfig.h:49:0,
                 from Marlin/src/HAL/STM32F1/MarlinSerial.cpp:25:
Marlin/src/HAL/STM32F1/../../inc/SanityCheck.h:782:6: error: #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination"
     #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination"
      ^~~~~
Marlin/src/HAL/STM32F1/../../inc/SanityCheck.h:851:6: error: #error "FILAMENT_CHANGE_UNLOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
     #error "FILAMENT_CHANGE_UNLOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
      ^~~~~
Marlin/src/HAL/STM32F1/../../inc/SanityCheck.h:1400:4: error: #error "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL."
   #error "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL."
    ^~~~~
*** [.pio/build/STM32F103RC_btt/src/src/HAL/STM32F1/HAL.cpp.o] Error 1
In file included from Marlin/src/HAL/STM32F1/../../inc/MarlinConfig.h:49:0,
                 from Marlin/src/HAL/STM32F1/SPI.cpp:43:
Marlin/src/HAL/STM32F1/../../inc/SanityCheck.h:782:6: error: #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination"
     #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination"
      ^~~~~
Marlin/src/HAL/STM32F1/../../inc/SanityCheck.h:851:6: error: #error "FILAMENT_CHANGE_UNLOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
     #error "FILAMENT_CHANGE_UNLOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
      ^~~~~
Marlin/src/HAL/STM32F1/../../inc/SanityCheck.h:1400:4: error: #error "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL."
   #error "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL."
    ^~~~~
*** [.pio/build/STM32F103RC_btt/src/src/HAL/STM32F1/HAL_SPI.cpp.o] Error 1
*** [.pio/build/STM32F103RC_btt/src/src/HAL/STM32F1/MarlinSerial.cpp.o] Error 1
*** [.pio/build/STM32F103RC_btt/src/src/HAL/STM32F1/SPI.cpp.o] Error 1
========================== [FAILED] Took 7.56 seconds ==========================

Environment      Status    Duration
---------------  --------  ------------
STM32F103RC_btt  FAILED    00:00:07.558
===================== 1 failed, 0 succeeded in 00:00:07.558 =====================
The terminal process "pio 'run'" terminated with exit code: 1.

Terminal will be reused by tasks, press any key to close it.