Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- [04030C0F][04030D07]
- DDR Calibration DQS reg = 00008989
- U-Boot 1.1.3 (Sep 10 2015 - 05:56:31)
- Board: Ralink APSoC DRAM: 128 MB
- relocate_code Pointer at: 87f68000
- flash manufacture id: c2, device id 20 19
- find flash: MX25L25635E
- ============================================
- Ralink UBoot Version: 4.3.0.0
- --------------------------------------------
- ASIC 7628_MP (Port5<->None)
- DRAM component: 1024 Mbits DDR, width 16
- DRAM bus: 16 bit
- Total memory: 128 MBytes
- Flash component: SPI Flash
- Date:Sep 10 2015 Time:05:56:31
- ============================================
- icache: sets:512, ways:4, linesz:32 ,total:65536
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- ##### The CPU freq = 580 MHZ ####
- estimate memory size =128 Mbytes
- RESET MT7628 PHY!!!!!!
- GPIOMODE --> 50054404
- GPIOMODE2 --> 5540551
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 0
- 3: System Boot system code via Flash.
- ## Booting image at bc050000 ...
- Image Name: MIPS OpenWrt Linux-3.18.23
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1194147 Bytes = 1.1 MB
- Load Address: 80000000
- Entry Point: 80000000
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 128
- Starting kernel ...
- [ 0.000000] Linux version 3.18.23 (blogic@debian) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49203) ) #5 Tue Sep 27 11:48:57 CEST 2016
- [ 0.000000] Board has DDR2
- [ 0.000000] Analog PMU set to hw control
- [ 0.000000] Digital PMU set to hw control
- [ 0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
- [ 0.000000] MIPS: machine is MediaTek LinkIt Smart 7688
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 08000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x07ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
- [ 0.000000] Kernel command line: console=ttyS2,57600 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
- [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
- [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Writing ErrCtl register=0006716d
- [ 0.000000] Readback ErrCtl register=0006716d
- [ 0.000000] Memory: 126140K/131072K available (2658K kernel code, 129K rwdata, 532K rodata, 192K init, 190K bss, 4932K reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] intc: using register map from devicetree
- [ 0.000000] CPU Clock: 580MHz
- [ 0.000000] clocksource_of_init: no matching clocksources found
- [ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
- [ 0.060000] pid_max: default: 32768 minimum: 301
- [ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.080000] pinctrl core: initialized pinctrl subsystem
- [ 0.090000] NET: Registered protocol family 16
- [ 0.110000] mt7621_gpio 10000600.gpio: registering 32 gpios
- [ 0.120000] mt7621_gpio 10000600.gpio: registering 32 gpios
- [ 0.130000] mt7621_gpio 10000600.gpio: registering 32 gpios
- [ 0.140000] Switched to clocksource MIPS
- [ 0.150000] NET: Registered protocol family 2
- [ 0.150000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.170000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.180000] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.190000] TCP: reno registered
- [ 0.200000] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.210000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.220000] NET: Registered protocol family 1
- [ 0.230000] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.250000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.270000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.290000] msgmni has been set to 246
- [ 0.290000] io scheduler noop registered
- [ 0.300000] io scheduler deadline registered (default)
- [ 0.310000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.330000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
- [ 0.350000] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
- [ 0.360000] console [ttyS2] disabled
- [ 0.370000] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A
- [ 0.390000] console [ttyS2] enabled
- [ 0.390000] console [ttyS2] enabled
- [ 0.400000] bootconsole [early0] disabled
- [ 0.400000] bootconsole [early0] disabled
- [ 0.420000] spi-mt7621 10000b00.spi: sys_freq: 193333333
- [ 0.450000] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
- [ 0.460000] m25p80 spi32766.0: using chunked io
- [ 0.470000] 4 ofpart partitions found on MTD device spi32766.0
- [ 0.480000] Creating 4 MTD partitions on "spi32766.0":
- [ 0.490000] 0x000000000000-0x000000030000 : "u-boot"
- [ 0.500000] 0x000000030000-0x000000040000 : "u-boot-env"
- [ 0.510000] 0x000000040000-0x000000050000 : "factory"
- [ 0.520000] 0x000000050000-0x000002000000 : "firmware"
- [ 0.600000] 2 uimage-fw partitions found on MTD device firmware
- [ 0.610000] 0x000000050000-0x0000001738e3 : "kernel"
- [ 0.620000] 0x0000001738e3-0x000002000000 : "rootfs"
- [ 0.630000] mtd: device 5 (rootfs) set to be root filesystem
- [ 0.640000] 1 squashfs-split partitions found on MTD device rootfs
- [ 0.650000] 0x000001560000-0x000002000000 : "rootfs_data"
- [ 0.680000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
- [ 0.690000] mt7621_wdt 10000120.watchdog: Initialized
- [ 0.700000] TCP: cubic registered
- [ 0.710000] NET: Registered protocol family 17
- [ 0.720000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 0.740000] Bridge firewalling registered
- [ 0.750000] 8021q: 802.1Q VLAN Support v1.8
- [ 0.760000] mtk-linkit bootstrap: Version : LINKITS7688D
- [ 0.770000] mtk-linkit bootstrap: Revision : REV3
- [ 0.790000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 0.800000] Freeing unused kernel memory: 192K (80340000 - 80370000)
- [ 2.090000] init: Console is alive
- [ 2.100000] init: - watchdog -
- [ 4.220000] usbcore: registered new interface driver usbfs
- [ 4.230000] usbcore: registered new interface driver hub
- [ 4.240000] usbcore: registered new device driver usb
- [ 4.260000] exFAT: Version 1.2.9
- [ 4.280000] SCSI subsystem initialized
- [ 4.290000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 4.300000] ehci-platform: EHCI generic platform driver
- [ 4.320000] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
- [ 4.340000] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
- [ 4.350000] ehci-platform 101c0000.ehci: EHCI Host Controller
- [ 4.360000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
- [ 4.380000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
- [ 4.410000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
- [ 4.420000] hub 1-0:1.0: USB hub found
- [ 4.430000] hub 1-0:1.0: 1 port detected
- [ 4.440000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 4.450000] ohci-platform: OHCI generic platform driver
- [ 4.460000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
- [ 4.480000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
- [ 4.490000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
- [ 4.560000] hub 2-0:1.0: USB hub found
- [ 4.570000] hub 2-0:1.0: 1 port detected
- [ 4.580000] platform gpio-leds: Driver leds-gpio requests probe deferral
- [ 4.600000] MTK MSDC device init.
- [ 4.650000] mtk-sd: MediaTek MT6575 MSDC Driver
- [ 4.660000] sdhci: Secure Digital Host Controller Interface driver
- [ 4.670000] sdhci: Copyright(c) Pierre Ossman
- [ 4.680000] platform gpio-leds: Driver leds-gpio requests probe deferral
- [ 4.690000] sdhci-pltfm: SDHCI platform and OF driver helper
- [ 4.710000] usbcore: registered new interface driver usb-storage
- [ 5.210000] init: - preinit -
- [ 6.260000] rt305x-esw 10110000.esw: link changed 0x00
- [ 6.470000] random: procd urandom read with 10 bits of entropy available
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 9.820000] jffs2: notice: (369) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 9.850000] mount_root: switching to jffs2 overlay
- [ 9.890000] procd: - early -
- [ 9.890000] procd: - watchdog -
- [ 10.710000] procd: - ubus -
- [ 11.720000] procd: - init -
- Please press Enter to activate this console.
- [ 14.490000] NET: Registered protocol family 10
- [ 14.590000] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 14.610000] i2c /dev entries driver
- [ 15.260000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
- [ 15.280000] <-- RTMPAllocAdapterBlock, Status=0
- [ 15.290000] mtk_gpio_wifi gpio-wifi: registering 1 gpio
- [ 15.330000] i2c-ralink 10000900.i2c: loaded
- [ 15.350000] Linux video capture interface: v2.00
- [ 15.390000] Enable Ralink GDMA Controller Module
- [ 15.400000] GDMA IP Version=3
- [ 15.560000] ******* mt76xx_pcm_init *******
- [ 15.570000] *******Enter codec_wm8960_i2c_probe********
- [ 15.580000] soc-audio soc-audio: ASoC: machine MTK APSoC I2S should use snd_soc_register_card()
- [ 15.600000] wm8960 0-001a: No platform data supplied
- [ 15.610000] soc-audio soc-audio: wm8960-hifi <-> mt76xx-i2s mapping ok
- [ 15.640000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 15.670000] nf_conntrack version 0.5.0 (1973 buckets, 7892 max)
- [ 15.710000] usbcore: registered new interface driver uvcvideo
- [ 15.720000] USB Video Class driver (1.1.1)
- [ 15.780000] xt_time: kernel timezone is -0000
- [ 15.810000] PPP generic driver version 2.4.2
- [ 15.820000] NET: Registered protocol family 24
- [ 21.700000] device eth0 entered promiscuous mode
- [ 21.730000] br-lan: port 1(eth0) entered forwarding state
- [ 21.740000] br-lan: port 1(eth0) entered forwarding state
- [ 22.320000] efuse_probe: efuse = 10000012
- [ 22.500000] tssi_0_target_pwr_g_band = 35
- [ 22.500000] tssi_1_target_pwr_g_band = 35
- [ 23.740000] br-lan: port 1(eth0) entered forwarding state
- [ 29.730000] <==== rt28xx_init, Status=0
- [ 31.110000] device ra0 entered promiscuous mode
- [ 31.120000] br-lan: port 2(ra0) entered forwarding state
- [ 31.130000] br-lan: port 2(ra0) entered forwarding state
- [ 33.130000] br-lan: port 2(ra0) entered forwarding state
- [ 58.150000] random: nonblocking pool is initialized
- [04030C0E][04030C0E]
- DDR Calibration DQS reg = 00008888
- U-Boot 1.1.3 (Sep 10 2015 - 05:56:31)
- Board: Ralink APSoC DRAM: 128 MB
- relocate_code Pointer at: 87f68000
- flash manufacture id: c2, device id 20 19
- find flash: MX25L25635E
- ============================================
- Ralink UBoot Version: 4.3.0.0
- --------------------------------------------
- ASIC 7628_MP (Port5<->None)
- DRAM component: 1024 Mbits DDR, width 16
- DRAM bus: 16 bit
- Total memory: 128 MBytes
- Flash component: SPI Flash
- Date:Sep 10 2015 Time:05:56:31
- ============================================
- icache: sets:512, ways:4, linesz:32 ,total:65536
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- ##### The CPU freq = 580 MHZ ####
- estimate memory size =128 Mbytes
- RESET MT7628 PHY!!!!!!
- GPIOMODE --> 50054404
- GPIOMODE2 --> 5540551
- RESET BUTTON PRESSED
- button pressed for 9 s
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 5: System Load Linux then write to Flash via USB Storage.
- (Re)start USB...
- USB0: *********ehci_hcd_init**********
- Mediatek/Ralink USB EHCI host init hccr b01c0000 and hcor b01c0010 hc_length 16
- 6. u2phydcr0(0xb0120860)=0x00aaaa02
- FM_OUT value: u4FmOut = 0(0x00000000)
- FM_OUT value: u4FmOut = 130(0x00000082)
- FM detection done! loop = 1
- SR calibration value u1SrCalVal = 6
- Register 1111 NbrPorts 1
- USB EHCI 1.00
- scanning bus 0 for devices... 1 USB Device(s) found
- scanning bus for storage devices... 0 Storage Device(s) found
- No USB Storage found. Upgrade F/W failed.
- [04030C0E][04030C0E]
- DDR Calibration DQS reg = 00008888
- U-Boot 1.1.3 (Sep 10 2015 - 05:56:31)
- Board: Ralink APSoC DRAM: 128 MB
- relocate_code Pointer at: 87f68000
- ******************************
- Software System Reset Occurred
- ******************************
- flash manufacture id: c2, device id 20 19
- find flash: MX25L25635E
- ============================================
- Ralink UBoot Version: 4.3.0.0
- --------------------------------------------
- ASIC 7628_MP (Port5<->None)
- DRAM component: 1024 Mbits DDR, width 16
- DRAM bus: 16 bit
- Total memory: 128 MBytes
- Flash component: SPI Flash
- Date:Sep 10 2015 Time:05:56:31
- ============================================
- icache: sets:512, ways:4, linesz:32 ,total:65536
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- ##### The CPU freq = 580 MHZ ####
- estimate memory size =128 Mbytes
- RESET MT7628 PHY!!!!!!
- GPIOMODE --> 50054404
- GPIOMODE2 --> 5540551
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 0
- 3: System Boot system code via Flash.
- ## Booting image at bc050000 ...
- Image Name: MIPS OpenWrt Linux-3.18.23
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1194147 Bytes = 1.1 MB
- Load Address: 80000000
- Entry Point: 80000000
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 128
- Starting kernel ...
- [ 0.000000] Linux version 3.18.23 (blogic@debian) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49203) ) #5 Tue Sep 27 11:48:57 CEST 2016
- [ 0.000000] Board has DDR2
- [ 0.000000] Analog PMU set to hw control
- [ 0.000000] Digital PMU set to hw control
- [ 0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
- [ 0.000000] MIPS: machine is MediaTek LinkIt Smart 7688
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 08000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x07ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
- [ 0.000000] Kernel command line: console=ttyS2,57600 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
- [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
- [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Writing ErrCtl register=00067160
- [ 0.000000] Readback ErrCtl register=00067160
- [ 0.000000] Memory: 126140K/131072K available (2658K kernel code, 129K rwdata, 532K rodata, 192K init, 190K bss, 4932K reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] intc: using register map from devicetree
- [ 0.000000] CPU Clock: 580MHz
- [ 0.000000] clocksource_of_init: no matching clocksources found
- [ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
- [ 0.060000] pid_max: default: 32768 minimum: 301
- [ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.080000] pinctrl core: initialized pinctrl subsystem
- [ 0.090000] NET: Registered protocol family 16
- [ 0.110000] mt7621_gpio 10000600.gpio: registering 32 gpios
- [ 0.120000] mt7621_gpio 10000600.gpio: registering 32 gpios
- [ 0.130000] mt7621_gpio 10000600.gpio: registering 32 gpios
- [ 0.140000] Switched to clocksource MIPS
- [ 0.150000] NET: Registered protocol family 2
- [ 0.150000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.170000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.180000] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.190000] TCP: reno registered
- [ 0.200000] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.210000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.220000] NET: Registered protocol family 1
- [ 0.230000] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.260000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.280000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.300000] msgmni has been set to 246
- [ 0.310000] io scheduler noop registered
- [ 0.310000] io scheduler deadline registered (default)
- [ 0.320000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.340000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
- [ 0.360000] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
- [ 0.380000] console [ttyS2] disabled
- [ 0.380000] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A
- [ 0.400000] console [ttyS2] enabled
- [ 0.400000] console [ttyS2] enabled
- [ 0.420000] bootconsole [early0] disabled
- [ 0.420000] bootconsole [early0] disabled
- [ 0.430000] spi-mt7621 10000b00.spi: sys_freq: 193333333
- [ 0.450000] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
- [ 0.470000] m25p80 spi32766.0: using chunked io
- [ 0.470000] 4 ofpart partitions found on MTD device spi32766.0
- [ 0.490000] Creating 4 MTD partitions on "spi32766.0":
- [ 0.500000] 0x000000000000-0x000000030000 : "u-boot"
- [ 0.510000] 0x000000030000-0x000000040000 : "u-boot-env"
- [ 0.520000] 0x000000040000-0x000000050000 : "factory"
- [ 0.530000] 0x000000050000-0x000002000000 : "firmware"
- [ 0.600000] 2 uimage-fw partitions found on MTD device firmware
- [ 0.610000] 0x000000050000-0x0000001738e3 : "kernel"
- [ 0.620000] 0x0000001738e3-0x000002000000 : "rootfs"
- [ 0.630000] mtd: device 5 (rootfs) set to be root filesystem
- [ 0.640000] 1 squashfs-split partitions found on MTD device rootfs
- [ 0.650000] 0x000001560000-0x000002000000 : "rootfs_data"
- [ 0.680000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
- [ 0.690000] mt7621_wdt 10000120.watchdog: Initialized
- [ 0.700000] TCP: cubic registered
- [ 0.710000] NET: Registered protocol family 17
- [ 0.720000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 0.740000] Bridge firewalling registered
- [ 0.750000] 8021q: 802.1Q VLAN Support v1.8
- [ 0.760000] mtk-linkit bootstrap: Version : LINKITS7688D
- [ 0.770000] mtk-linkit bootstrap: Revision : REV3
- [ 0.790000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 0.800000] Freeing unused kernel memory: 192K (80340000 - 80370000)
- [ 2.100000] init: Console is alive
- [ 2.100000] init: - watchdog -
- [ 4.220000] usbcore: registered new interface driver usbfs
- [ 4.230000] usbcore: registered new interface driver hub
- [ 4.240000] usbcore: registered new device driver usb
- [ 4.260000] exFAT: Version 1.2.9
- [ 4.280000] SCSI subsystem initialized
- [ 4.290000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 4.300000] ehci-platform: EHCI generic platform driver
- [ 4.320000] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
- [ 4.340000] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
- [ 4.350000] ehci-platform 101c0000.ehci: EHCI Host Controller
- [ 4.360000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
- [ 4.380000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
- [ 4.410000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
- [ 4.420000] hub 1-0:1.0: USB hub found
- [ 4.430000] hub 1-0:1.0: 1 port detected
- [ 4.440000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 4.450000] ohci-platform: OHCI generic platform driver
- [ 4.460000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
- [ 4.480000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
- [ 4.490000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
- [ 4.560000] hub 2-0:1.0: USB hub found
- [ 4.570000] hub 2-0:1.0: 1 port detected
- [ 4.580000] platform gpio-leds: Driver leds-gpio requests probe deferral
- [ 4.600000] MTK MSDC device init.
- [ 4.650000] mtk-sd: MediaTek MT6575 MSDC Driver
- [ 4.660000] sdhci: Secure Digital Host Controller Interface driver
- [ 4.670000] sdhci: Copyright(c) Pierre Ossman
- [ 4.680000] platform gpio-leds: Driver leds-gpio requests probe deferral
- [ 4.690000] sdhci-pltfm: SDHCI platform and OF driver helper
- [ 4.710000] usbcore: registered new interface driver usb-storage
- [ 5.210000] init: - preinit -
- [ 6.260000] rt305x-esw 10110000.esw: link changed 0x00
- [ 6.470000] random: mktemp urandom read with 10 bits of entropy available
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 9.810000] jffs2: notice: (368) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 9.840000] mount_root: switching to jffs2 overlay
- [ 9.880000] procd: - early -
- [ 9.880000] procd: - watchdog -
- [ 10.710000] procd: - ubus -
- Command failed: Not found
- [ 11.720000] procd: - init -
- Please press Enter to activate this console.
- [ 14.500000] NET: Registered protocol family 10
- [ 14.600000] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 14.620000] i2c /dev entries driver
- [ 15.280000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
- [ 15.290000] <-- RTMPAllocAdapterBlock, Status=0
- [ 15.300000] mtk_gpio_wifi gpio-wifi: registering 1 gpio
- [ 15.340000] i2c-ralink 10000900.i2c: loaded
- [ 15.360000] Linux video capture interface: v2.00
- [ 15.400000] Enable Ralink GDMA Controller Module
- [ 15.410000] GDMA IP Version=3
- [ 15.570000] ******* mt76xx_pcm_init *******
- [ 15.580000] *******Enter codec_wm8960_i2c_probe********
- [ 15.590000] soc-audio soc-audio: ASoC: machine MTK APSoC I2S should use snd_soc_register_card()
- [ 15.600000] wm8960 0-001a: No platform data supplied
- [ 15.620000] soc-audio soc-audio: wm8960-hifi <-> mt76xx-i2s mapping ok
- [ 15.640000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 15.670000] nf_conntrack version 0.5.0 (1973 buckets, 7892 max)
- [ 15.710000] usbcore: registered new interface driver uvcvideo
- [ 15.720000] USB Video Class driver (1.1.1)
- [ 15.750000] xt_time: kernel timezone is -0000
- [ 15.790000] PPP generic driver version 2.4.2
- [ 15.810000] NET: Registered protocol family 24
- [ 21.660000] device eth0 entered promiscuous mode
- [ 21.710000] br-lan: port 1(eth0) entered forwarding state
- [ 21.720000] br-lan: port 1(eth0) entered forwarding state
- [ 22.450000] efuse_probe: efuse = 10000012
- [ 22.680000] tssi_0_target_pwr_g_band = 35
- [ 22.690000] tssi_1_target_pwr_g_band = 35
- [ 23.720000] br-lan: port 1(eth0) entered forwarding state
- [ 29.430000] <==== rt28xx_init, Status=0
- [ 30.810000] device ra0 entered promiscuous mode
- [ 30.820000] br-lan: port 2(ra0) entered forwarding state
- [ 30.830000] br-lan: port 2(ra0) entered forwarding state
- [ 32.830000] br-lan: port 2(ra0) entered forwarding state
- [ 57.560000] random: nonblocking pool is initialized
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement