API tools faq
paste
Advertisement
felixlt

Configuration_adv.h

felixlt
May 26th, 2020
408
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 136.97 KB | None | 0 0
raw download clone embed print report
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23.  
  24. /**
  25. * Configuration_adv.h
  26. *
  27. * Advanced settings.
  28. * Only change these if you know exactly what you're doing.
  29. * Some of these settings can damage your printer if improperly set!
  30. *
  31. * Basic settings can be found in Configuration.h
  32. *
  33. */
  34. #define CONFIGURATION_ADV_H_VERSION 020005
  35.  
  36. // @section temperature
  37.  
  38. //===========================================================================
  39. //=============================Thermal Settings ============================
  40. //===========================================================================
  41.  
  42. /**
  43. * Thermocouple sensors are quite sensitive to noise. Any noise induced in
  44. * the sensor wires, such as by stepper motor wires run in parallel to them,
  45. * may result in the thermocouple sensor reporting spurious errors. This
  46. * value is the number of errors which can occur in a row before the error
  47. * is reported. This allows us to ignore intermittent error conditions while
  48. * still detecting an actual failure, which should result in a continuous
  49. * stream of errors from the sensor.
  50. *
  51. * Set this value to 0 to fail on the first error to occur.
  52. */
  53. #define THERMOCOUPLE_MAX_ERRORS 15
  54.  
  55. //
  56. // Custom Thermistor 1000 parameters
  57. //
  58. #if TEMP_SENSOR_0 == 1000
  59. #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  60. #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  61. #define HOTEND0_BETA 3950 // Beta value
  62. #endif
  63.  
  64. #if TEMP_SENSOR_1 == 1000
  65. #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  66. #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  67. #define HOTEND1_BETA 3950 // Beta value
  68. #endif
  69.  
  70. #if TEMP_SENSOR_2 == 1000
  71. #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  72. #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  73. #define HOTEND2_BETA 3950 // Beta value
  74. #endif
  75.  
  76. #if TEMP_SENSOR_3 == 1000
  77. #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  78. #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  79. #define HOTEND3_BETA 3950 // Beta value
  80. #endif
  81.  
  82. #if TEMP_SENSOR_4 == 1000
  83. #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  84. #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  85. #define HOTEND4_BETA 3950 // Beta value
  86. #endif
  87.  
  88. #if TEMP_SENSOR_5 == 1000
  89. #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  90. #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  91. #define HOTEND5_BETA 3950 // Beta value
  92. #endif
  93.  
  94. #if TEMP_SENSOR_6 == 1000
  95. #define HOTEND6_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  96. #define HOTEND6_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  97. #define HOTEND6_BETA 3950 // Beta value
  98. #endif
  99.  
  100. #if TEMP_SENSOR_7 == 1000
  101. #define HOTEND7_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  102. #define HOTEND7_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  103. #define HOTEND7_BETA 3950 // Beta value
  104. #endif
  105.  
  106. #if TEMP_SENSOR_BED == 1000
  107. #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  108. #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  109. #define BED_BETA 3950 // Beta value
  110. #endif
  111.  
  112. #if TEMP_SENSOR_CHAMBER == 1000
  113. #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor
  114. #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C
  115. #define CHAMBER_BETA 3950 // Beta value
  116. #endif
  117.  
  118. //
  119. // Hephestos 2 24V heated bed upgrade kit.
  120. // https://store.bq.com/en/heated-bed-kit-hephestos2
  121. //
  122. //#define HEPHESTOS2_HEATED_BED_KIT
  123. #if ENABLED(HEPHESTOS2_HEATED_BED_KIT)
  124. #undef TEMP_SENSOR_BED
  125. #define TEMP_SENSOR_BED 70
  126. #define HEATER_BED_INVERTING true
  127. #endif
  128.  
  129. /**
  130. * Heated Chamber settings
  131. */
  132. #if TEMP_SENSOR_CHAMBER
  133. #define CHAMBER_MINTEMP 5
  134. #define CHAMBER_MAXTEMP 60
  135. #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
  136. //#define CHAMBER_LIMIT_SWITCHING
  137. //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
  138. //#define HEATER_CHAMBER_INVERTING false
  139. #endif
  140.  
  141. #if DISABLED(PIDTEMPBED)
  142. #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
  143. #if ENABLED(BED_LIMIT_SWITCHING)
  144. #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
  145. #endif
  146. #endif
  147.  
  148. /**
  149. * Thermal Protection provides additional protection to your printer from damage
  150. * and fire. Marlin always includes safe min and max temperature ranges which
  151. * protect against a broken or disconnected thermistor wire.
  152. *
  153. * The issue: If a thermistor falls out, it will report the much lower
  154. * temperature of the air in the room, and the the firmware will keep
  155. * the heater on.
  156. *
  157. * The solution: Once the temperature reaches the target, start observing.
  158. * If the temperature stays too far below the target (hysteresis) for too
  159. * long (period), the firmware will halt the machine as a safety precaution.
  160. *
  161. * If you get false positives for "Thermal Runaway", increase
  162. * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  163. */
  164. #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  165. #define THERMAL_PROTECTION_PERIOD 40 // Seconds
  166. #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
  167.  
  168. //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops
  169. #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
  170. //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303
  171. #endif
  172.  
  173. /**
  174. * Whenever an M104, M109, or M303 increases the target temperature, the
  175. * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature
  176. * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and
  177. * requires a hard reset. This test restarts with any M104/M109/M303, but only
  178. * if the current temperature is far enough below the target for a reliable
  179. * test.
  180. *
  181. * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD
  182. * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
  183. * below 2.
  184. */
  185. #define WATCH_TEMP_PERIOD 20 // Seconds
  186. #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
  187. #endif
  188.  
  189. /**
  190. * Thermal Protection parameters for the bed are just as above for hotends.
  191. */
  192. #if ENABLED(THERMAL_PROTECTION_BED)
  193. #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
  194. #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
  195.  
  196. /**
  197. * As described above, except for the bed (M140/M190/M303).
  198. */
  199. #define WATCH_BED_TEMP_PERIOD 60 // Seconds
  200. #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
  201. #endif
  202.  
  203. /**
  204. * Thermal Protection parameters for the heated chamber.
  205. */
  206. #if ENABLED(THERMAL_PROTECTION_CHAMBER)
  207. #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
  208. #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
  209.  
  210. /**
  211. * Heated chamber watch settings (M141/M191).
  212. */
  213. #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
  214. #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
  215. #endif
  216.  
  217. #if ENABLED(PIDTEMP)
  218. // Add an experimental additional term to the heater power, proportional to the extrusion speed.
  219. // A well-chosen Kc value should add just enough power to melt the increased material volume.
  220. //#define PID_EXTRUSION_SCALING
  221. #if ENABLED(PID_EXTRUSION_SCALING)
  222. #define DEFAULT_Kc (100) // heating power = Kc * e_speed
  223. #define LPQ_MAX_LEN 50
  224. #endif
  225.  
  226. /**
  227. * Add an experimental additional term to the heater power, proportional to the fan speed.
  228. * A well-chosen Kf value should add just enough power to compensate for power-loss from the cooling fan.
  229. * You can either just add a constant compensation with the DEFAULT_Kf value
  230. * or follow the instruction below to get speed-dependent compensation.
  231. *
  232. * Constant compensation (use only with fanspeeds of 0% and 100%)
  233. * ---------------------------------------------------------------------
  234. * A good starting point for the Kf-value comes from the calculation:
  235. * kf = (power_fan * eff_fan) / power_heater * 255
  236. * where eff_fan is between 0.0 and 1.0, based on fan-efficiency and airflow to the nozzle / heater.
  237. *
  238. * Example:
  239. * Heater: 40W, Fan: 0.1A * 24V = 2.4W, eff_fan = 0.8
  240. * Kf = (2.4W * 0.8) / 40W * 255 = 12.24
  241. *
  242. * Fan-speed dependent compensation
  243. * --------------------------------
  244. * 1. To find a good Kf value, set the hotend temperature, wait for it to settle, and enable the fan (100%).
  245. * Make sure PID_FAN_SCALING_LIN_FACTOR is 0 and PID_FAN_SCALING_ALTERNATIVE_DEFINITION is not enabled.
  246. * If you see the temperature drop repeat the test, increasing the Kf value slowly, until the temperature
  247. * drop goes away. If the temperature overshoots after enabling the fan, the Kf value is too big.
  248. * 2. Note the Kf-value for fan-speed at 100%
  249. * 3. Determine a good value for PID_FAN_SCALING_MIN_SPEED, which is around the speed, where the fan starts moving.
  250. * 4. Repeat step 1. and 2. for this fan speed.
  251. * 5. Enable PID_FAN_SCALING_ALTERNATIVE_DEFINITION and enter the two identified Kf-values in
  252. * PID_FAN_SCALING_AT_FULL_SPEED and PID_FAN_SCALING_AT_MIN_SPEED. Enter the minimum speed in PID_FAN_SCALING_MIN_SPEED
  253. */
  254. //#define PID_FAN_SCALING
  255. #if ENABLED(PID_FAN_SCALING)
  256. //#define PID_FAN_SCALING_ALTERNATIVE_DEFINITION
  257. #if ENABLED(PID_FAN_SCALING_ALTERNATIVE_DEFINITION)
  258. // The alternative definition is used for an easier configuration.
  259. // Just figure out Kf at fullspeed (255) and PID_FAN_SCALING_MIN_SPEED.
  260. // DEFAULT_Kf and PID_FAN_SCALING_LIN_FACTOR are calculated accordingly.
  261.  
  262. #define PID_FAN_SCALING_AT_FULL_SPEED 13.0 //=PID_FAN_SCALING_LIN_FACTOR*255+DEFAULT_Kf
  263. #define PID_FAN_SCALING_AT_MIN_SPEED 6.0 //=PID_FAN_SCALING_LIN_FACTOR*PID_FAN_SCALING_MIN_SPEED+DEFAULT_Kf
  264. #define PID_FAN_SCALING_MIN_SPEED 10.0 // Minimum fan speed at which to enable PID_FAN_SCALING
  265.  
  266. #define DEFAULT_Kf (255.0*PID_FAN_SCALING_AT_MIN_SPEED-PID_FAN_SCALING_AT_FULL_SPEED*PID_FAN_SCALING_MIN_SPEED)/(255.0-PID_FAN_SCALING_MIN_SPEED)
  267. #define PID_FAN_SCALING_LIN_FACTOR (PID_FAN_SCALING_AT_FULL_SPEED-DEFAULT_Kf)/255.0
  268.  
  269. #else
  270. #define PID_FAN_SCALING_LIN_FACTOR (0) // Power loss due to cooling = Kf * (fan_speed)
  271. #define DEFAULT_Kf 10 // A constant value added to the PID-tuner
  272. #define PID_FAN_SCALING_MIN_SPEED 10 // Minimum fan speed at which to enable PID_FAN_SCALING
  273. #endif
  274. #endif
  275. #endif
  276.  
  277. /**
  278. * Automatic Temperature Mode
  279. *
  280. * Dynamically adjust the hotend target temperature based on planned E moves.
  281. *
  282. * (Contrast with PID_EXTRUSION_SCALING, which tracks E movement and adjusts PID
  283. * behavior using an additional kC value.)
  284. *
  285. * Autotemp is calculated by (mintemp + factor * mm_per_sec), capped to maxtemp.
  286. *
  287. * Enable Autotemp Mode with M104/M109 F<factor> S<mintemp> B<maxtemp>.
  288. * Disable by sending M104/M109 with no F parameter (or F0 with AUTOTEMP_PROPORTIONAL).
  289. */
  290. #define AUTOTEMP
  291. #if ENABLED(AUTOTEMP)
  292. #define AUTOTEMP_OLDWEIGHT 0.98
  293. // Turn on AUTOTEMP on M104/M109 by default using proportions set here
  294. //#define AUTOTEMP_PROPORTIONAL
  295. #if ENABLED(AUTOTEMP_PROPORTIONAL)
  296. #define AUTOTEMP_MIN_P 0 // (°C) Added to the target temperature
  297. #define AUTOTEMP_MAX_P 5 // (°C) Added to the target temperature
  298. #define AUTOTEMP_FACTOR_P 1 // Apply this F parameter by default (overridden by M104/M109 F)
  299. #endif
  300. #endif
  301.  
  302. // Show Temperature ADC value
  303. // Enable for M105 to include ADC values read from temperature sensors.
  304. //#define SHOW_TEMP_ADC_VALUES
  305.  
  306. /**
  307. * High Temperature Thermistor Support
  308. *
  309. * Thermistors able to support high temperature tend to have a hard time getting
  310. * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP
  311. * will probably be caught when the heating element first turns on during the
  312. * preheating process, which will trigger a min_temp_error as a safety measure
  313. * and force stop everything.
  314. * To circumvent this limitation, we allow for a preheat time (during which,
  315. * min_temp_error won't be triggered) and add a min_temp buffer to handle
  316. * aberrant readings.
  317. *
  318. * If you want to enable this feature for your hotend thermistor(s)
  319. * uncomment and set values > 0 in the constants below
  320. */
  321.  
  322. // The number of consecutive low temperature errors that can occur
  323. // before a min_temp_error is triggered. (Shouldn't be more than 10.)
  324. //#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
  325.  
  326. // The number of milliseconds a hotend will preheat before starting to check
  327. // the temperature. This value should NOT be set to the time it takes the
  328. // hot end to reach the target temperature, but the time it takes to reach
  329. // the minimum temperature your thermistor can read. The lower the better/safer.
  330. // This shouldn't need to be more than 30 seconds (30000)
  331. //#define MILLISECONDS_PREHEAT_TIME 0
  332.  
  333. // @section extruder
  334.  
  335. // Extruder runout prevention.
  336. // If the machine is idle and the temperature over MINTEMP
  337. // then extrude some filament every couple of SECONDS.
  338. //#define EXTRUDER_RUNOUT_PREVENT
  339. #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
  340. #define EXTRUDER_RUNOUT_MINTEMP 190
  341. #define EXTRUDER_RUNOUT_SECONDS 30
  342. #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m)
  343. #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm)
  344. #endif
  345.  
  346. /**
  347. * Hotend Idle Timeout
  348. * Prevent filament in the nozzle from charring and causing a critical jam.
  349. */
  350. //#define HOTEND_IDLE_TIMEOUT
  351. #if ENABLED(HOTEND_IDLE_TIMEOUT)
  352. #define HOTEND_IDLE_TIMEOUT_SEC (5*60) // (seconds) Time without extruder movement to trigger protection
  353. #define HOTEND_IDLE_MIN_TRIGGER 180 // (°C) Minimum temperature to enable hotend protection
  354. #define HOTEND_IDLE_NOZZLE_TARGET 0 // (°C) Safe temperature for the nozzle after timeout
  355. #define HOTEND_IDLE_BED_TARGET 0 // (°C) Safe temperature for the bed after timeout
  356. #endif
  357.  
  358. // @section temperature
  359.  
  360. // Calibration for AD595 / AD8495 sensor to adjust temperature measurements.
  361. // The final temperature is calculated as (measuredTemp * GAIN) + OFFSET.
  362. #define TEMP_SENSOR_AD595_OFFSET 0.0
  363. #define TEMP_SENSOR_AD595_GAIN 1.0
  364. #define TEMP_SENSOR_AD8495_OFFSET 0.0
  365. #define TEMP_SENSOR_AD8495_GAIN 1.0
  366.  
  367. /**
  368. * Controller Fan
  369. * To cool down the stepper drivers and MOSFETs.
  370. *
  371. * The fan turns on automatically whenever any driver is enabled and turns
  372. * off (or reduces to idle speed) shortly after drivers are turned off.
  373. */
  374. //#define USE_CONTROLLER_FAN
  375. #if ENABLED(USE_CONTROLLER_FAN)
  376. //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan
  377. //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered
  378. #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.)
  379. #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled
  380. #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled
  381. #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors
  382. //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
  383. #if ENABLED(CONTROLLER_FAN_EDITABLE)
  384. #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
  385. #endif
  386. #endif
  387.  
  388. // When first starting the main fan, run it at full speed for the
  389. // given number of milliseconds. This gets the fan spinning reliably
  390. // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
  391. //#define FAN_KICKSTART_TIME 100
  392.  
  393. // Some coolers may require a non-zero "off" state.
  394. //#define FAN_OFF_PWM 1
  395.  
  396. /**
  397. * PWM Fan Scaling
  398. *
  399. * Define the min/max speeds for PWM fans (as set with M106).
  400. *
  401. * With these options the M106 0-255 value range is scaled to a subset
  402. * to ensure that the fan has enough power to spin, or to run lower
  403. * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
  404. * Value 0 always turns off the fan.
  405. *
  406. * Define one or both of these to override the default 0-255 range.
  407. */
  408. //#define FAN_MIN_PWM 50
  409. //#define FAN_MAX_PWM 128
  410.  
  411. /**
  412. * FAST PWM FAN Settings
  413. *
  414. * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h)
  415. * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a
  416. * frequency as close as possible to the desired frequency.
  417. *
  418. * FAST_PWM_FAN_FREQUENCY [undefined by default]
  419. * Set this to your desired frequency.
  420. * If left undefined this defaults to F = F_CPU/(2*255*1)
  421. * i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
  422. * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
  423. * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
  424. *
  425. * USE_OCR2A_AS_TOP [undefined by default]
  426. * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
  427. * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz]
  428. * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz]
  429. * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of
  430. * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
  431. * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies.
  432. */
  433. #if ENABLED(FAST_PWM_FAN)
  434. //#define FAST_PWM_FAN_FREQUENCY 31400
  435. //#define USE_OCR2A_AS_TOP
  436. #endif
  437.  
  438. // @section extruder
  439.  
  440. /**
  441. * Extruder cooling fans
  442. *
  443. * Extruder auto fans automatically turn on when their extruders'
  444. * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE.
  445. *
  446. * Your board's pins file specifies the recommended pins. Override those here
  447. * or set to -1 to disable completely.
  448. *
  449. * Multiple extruders can be assigned to the same pin in which case
  450. * the fan will turn on when any selected extruder is above the threshold.
  451. */
  452. #define E0_AUTO_FAN_PIN P2_04
  453. #define E1_AUTO_FAN_PIN -1
  454. #define E2_AUTO_FAN_PIN -1
  455. #define E3_AUTO_FAN_PIN -1
  456. #define E4_AUTO_FAN_PIN -1
  457. #define E5_AUTO_FAN_PIN -1
  458. #define E6_AUTO_FAN_PIN -1
  459. #define E7_AUTO_FAN_PIN -1
  460. #define CHAMBER_AUTO_FAN_PIN -1
  461.  
  462. #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
  463. #define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed
  464. #define CHAMBER_AUTO_FAN_TEMPERATURE 30
  465. #define CHAMBER_AUTO_FAN_SPEED 255
  466.  
  467. /**
  468. * Part-Cooling Fan Multiplexer
  469. *
  470. * This feature allows you to digitally multiplex the fan output.
  471. * The multiplexer is automatically switched at tool-change.
  472. * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans.
  473. */
  474. #define FANMUX0_PIN -1
  475. #define FANMUX1_PIN -1
  476. #define FANMUX2_PIN -1
  477.  
  478. /**
  479. * M355 Case Light on-off / brightness
  480. */
  481. //#define CASE_LIGHT_ENABLE
  482. #if ENABLED(CASE_LIGHT_ENABLE)
  483. //#define CASE_LIGHT_PIN 4 // Override the default pin if needed
  484. #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
  485. #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
  486. #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
  487. //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm
  488. //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu
  489. //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting.
  490. //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED.
  491. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL)
  492. #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
  493. #endif
  494. #endif
  495.  
  496. // @section homing
  497.  
  498. // If you want endstops to stay on (by default) even when not homing
  499. // enable this option. Override at any time with M120, M121.
  500. //#define ENDSTOPS_ALWAYS_ON_DEFAULT
  501.  
  502. // @section extras
  503.  
  504. //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
  505.  
  506. // Employ an external closed loop controller. Override pins here if needed.
  507. //#define EXTERNAL_CLOSED_LOOP_CONTROLLER
  508. #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
  509. //#define CLOSED_LOOP_ENABLE_PIN -1
  510. //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
  511. #endif
  512.  
  513. /**
  514. * Dual Steppers / Dual Endstops
  515. *
  516. * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes.
  517. *
  518. * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to
  519. * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop
  520. * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug
  521. * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'.
  522. *
  523. * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors
  524. * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error
  525. * in X2. Dual endstop offsets can be set at runtime with 'M666 X<offset> Y<offset> Z<offset>'.
  526. */
  527.  
  528. //#define X_DUAL_STEPPER_DRIVERS
  529. #if ENABLED(X_DUAL_STEPPER_DRIVERS)
  530. #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions
  531. //#define X_DUAL_ENDSTOPS
  532. #if ENABLED(X_DUAL_ENDSTOPS)
  533. #define X2_USE_ENDSTOP _XMAX_
  534. #define X2_ENDSTOP_ADJUSTMENT 0
  535. #endif
  536. #endif
  537.  
  538. //#define Y_DUAL_STEPPER_DRIVERS
  539. #if ENABLED(Y_DUAL_STEPPER_DRIVERS)
  540. #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions
  541. //#define Y_DUAL_ENDSTOPS
  542. #if ENABLED(Y_DUAL_ENDSTOPS)
  543. #define Y2_USE_ENDSTOP _YMAX_
  544. #define Y2_ENDSTOP_ADJUSTMENT 0
  545. #endif
  546. #endif
  547.  
  548. //
  549. // For Z set the number of stepper drivers
  550. //
  551. #define NUM_Z_STEPPER_DRIVERS 1 // (1-4) Z options change based on how many
  552.  
  553. #if NUM_Z_STEPPER_DRIVERS > 1
  554. //#define Z_MULTI_ENDSTOPS
  555. #if ENABLED(Z_MULTI_ENDSTOPS)
  556. #define Z2_USE_ENDSTOP _XMAX_
  557. #define Z2_ENDSTOP_ADJUSTMENT 0
  558. #if NUM_Z_STEPPER_DRIVERS >= 3
  559. #define Z3_USE_ENDSTOP _YMAX_
  560. #define Z3_ENDSTOP_ADJUSTMENT 0
  561. #endif
  562. #if NUM_Z_STEPPER_DRIVERS >= 4
  563. #define Z4_USE_ENDSTOP _ZMAX_
  564. #define Z4_ENDSTOP_ADJUSTMENT 0
  565. #endif
  566. #endif
  567. #endif
  568.  
  569. /**
  570. * Dual X Carriage
  571. *
  572. * This setup has two X carriages that can move independently, each with its own hotend.
  573. * The carriages can be used to print an object with two colors or materials, or in
  574. * "duplication mode" it can print two identical or X-mirrored objects simultaneously.
  575. * The inactive carriage is parked automatically to prevent oozing.
  576. * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis.
  577. * By default the X2 stepper is assigned to the first unused E plug on the board.
  578. *
  579. * The following Dual X Carriage modes can be selected with M605 S<mode>:
  580. *
  581. * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel
  582. * results as long as it supports dual X-carriages. (M605 S0)
  583. *
  584. * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so
  585. * that additional slicer support is not required. (M605 S1)
  586. *
  587. * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with
  588. * the first X-carriage and extruder, to print 2 copies of the same object at the same time.
  589. * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and
  590. * follow with M605 S2 to initiate duplicated movement.
  591. *
  592. * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates
  593. * the movement of the first except the second extruder is reversed in the X axis.
  594. * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and
  595. * follow with M605 S3 to initiate mirrored movement.
  596. */
  597. //#define DUAL_X_CARRIAGE
  598. #if ENABLED(DUAL_X_CARRIAGE)
  599. #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS
  600. #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage
  601. #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage
  602. #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed
  603. #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position
  604. #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS.
  605. // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
  606. // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
  607. // without modifying the firmware (through the "M218 T1 X???" command).
  608. // Remember: you should set the second extruder x-offset to 0 in your slicer.
  609.  
  610. // This is the default power-up mode which can be later using M605.
  611. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE
  612.  
  613. // Default x offset in duplication mode (typically set to half print bed width)
  614. #define DEFAULT_DUPLICATION_X_OFFSET 100
  615. #endif
  616.  
  617. // Activate a solenoid on the active extruder with M380. Disable all with M381.
  618. // Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
  619. //#define EXT_SOLENOID
  620.  
  621. // @section homing
  622.  
  623. /**
  624. * Homing Procedure
  625. * Homing (G28) does an indefinite move towards the endstops to establish
  626. * the position of the toolhead relative to the workspace.
  627. */
  628.  
  629. //#define SENSORLESS_BACKOFF_MM { 2, 2 } // (mm) Backoff from endstops before sensorless homing
  630.  
  631. #define HOMING_BUMP_MM { 5, 5, 2 } // (mm) Backoff from endstops after first bump
  632. #define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)
  633.  
  634. //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (mm) Backoff from endstops after homing
  635.  
  636. #define QUICK_HOME // If G28 contains XY do a diagonal move first
  637. //#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X
  638. //#define CODEPENDENT_XY_HOMING // If X/Y can't home without homing Y/X first
  639.  
  640. // @section bltouch
  641.  
  642. #if ENABLED(BLTOUCH)
  643. /**
  644. * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
  645. * Do not activate settings that the probe might not understand. Clones might misunderstand
  646. * advanced commands.
  647. *
  648. * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
  649. * check the wiring of the BROWN, RED and ORANGE wires.
  650. *
  651. * Note: If the trigger signal of your probe is not being recognized, it has been very often
  652. * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
  653. * like they would be with a real switch. So please check the wiring first.
  654. *
  655. * Settings for all BLTouch and clone probes:
  656. */
  657.  
  658. // Safety: The probe needs time to recognize the command.
  659. // Minimum command delay (ms). Enable and increase if needed.
  660. //#define BLTOUCH_DELAY 500
  661.  
  662. /**
  663. * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
  664. */
  665.  
  666. // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
  667. // in special cases, like noisy or filtered input configurations.
  668. //#define BLTOUCH_FORCE_SW_MODE
  669.  
  670. /**
  671. * Settings for BLTouch Smart 3.0 and 3.1
  672. * Summary:
  673. * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
  674. * - High-Speed mode
  675. * - Disable LCD voltage options
  676. */
  677.  
  678. /**
  679. * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
  680. * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
  681. * If disabled, OD mode is the hard-coded default on 3.0
  682. * On startup, Marlin will compare its eeprom to this vale. If the selected mode
  683. * differs, a mode set eeprom write will be completed at initialization.
  684. * Use the option below to force an eeprom write to a V3.1 probe regardless.
  685. */
  686. #define BLTOUCH_SET_5V_MODE
  687.  
  688. /**
  689. * Safety: Activate if connecting a probe with an unknown voltage mode.
  690. * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
  691. * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
  692. * To preserve the life of the probe, use this once then turn it off and re-flash.
  693. */
  694. //#define BLTOUCH_FORCE_MODE_SET
  695.  
  696. /**
  697. * Use "HIGH SPEED" mode for probing.
  698. * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
  699. * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
  700. * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
  701. */
  702. //#define BLTOUCH_HS_MODE
  703.  
  704. // Safety: Enable voltage mode settings in the LCD menu.
  705. //#define BLTOUCH_LCD_VOLTAGE_MENU
  706.  
  707. #endif // BLTOUCH
  708.  
  709. // @section extras
  710.  
  711. /**
  712. * Z Steppers Auto-Alignment
  713. * Add the G34 command to align multiple Z steppers using a bed probe.
  714. */
  715. //#define Z_STEPPER_AUTO_ALIGN
  716. #if ENABLED(Z_STEPPER_AUTO_ALIGN)
  717. // Define probe X and Y positions for Z1, Z2 [, Z3 [, Z4]]
  718. // If not defined, probe limits will be used.
  719. // Override with 'M422 S<index> X<pos> Y<pos>'
  720. //#define Z_STEPPER_ALIGN_XY { { 10, 190 }, { 100, 10 }, { 190, 190 } }
  721.  
  722. /**
  723. * Orientation for the automatically-calculated probe positions.
  724. * Override Z stepper align points with 'M422 S<index> X<pos> Y<pos>'
  725. *
  726. * 2 Steppers: (0) (1)
  727. * | | 2 |
  728. * | 1 2 | |
  729. * | | 1 |
  730. *
  731. * 3 Steppers: (0) (1) (2) (3)
  732. * | 3 | 1 | 2 1 | 2 |
  733. * | | 3 | | 3 |
  734. * | 1 2 | 2 | 3 | 1 |
  735. *
  736. * 4 Steppers: (0) (1) (2) (3)
  737. * | 4 3 | 1 4 | 2 1 | 3 2 |
  738. * | | | | |
  739. * | 1 2 | 2 3 | 3 4 | 4 1 |
  740. *
  741. */
  742. #ifndef Z_STEPPER_ALIGN_XY
  743. //#define Z_STEPPERS_ORIENTATION 0
  744. #endif
  745.  
  746. // Provide Z stepper positions for more rapid convergence in bed alignment.
  747. // Requires triple stepper drivers (i.e., set NUM_Z_STEPPER_DRIVERS to 3)
  748. //#define Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS
  749. #if ENABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
  750. // Define Stepper XY positions for Z1, Z2, Z3 corresponding to
  751. // the Z screw positions in the bed carriage.
  752. // Define one position per Z stepper in stepper driver order.
  753. #define Z_STEPPER_ALIGN_STEPPER_XY { { 210.7, 102.5 }, { 152.6, 220.0 }, { 94.5, 102.5 } }
  754. #else
  755. // Amplification factor. Used to scale the correction step up or down in case
  756. // the stepper (spindle) position is farther out than the test point.
  757. #define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
  758. #endif
  759.  
  760. #define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
  761. #define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
  762. #define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
  763. #define RESTORE_LEVELING_AFTER_G34 // Restore leveling after G34 is done?
  764. // After G34, re-home Z (G28 Z) or just calculate it from the last probe heights?
  765. // Re-homing might be more precise in reproducing the actual 'G28 Z' homing height, especially on an uneven bed.
  766. #define HOME_AFTER_G34
  767. #endif
  768.  
  769. // @section motion
  770.  
  771. #define AXIS_RELATIVE_MODES { false, false, false, false }
  772.  
  773. // Add a Duplicate option for well-separated conjoined nozzles
  774. //#define MULTI_NOZZLE_DUPLICATION
  775.  
  776. // By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
  777. #define INVERT_X_STEP_PIN false
  778. #define INVERT_Y_STEP_PIN false
  779. #define INVERT_Z_STEP_PIN false
  780. #define INVERT_E_STEP_PIN false
  781.  
  782. // Default stepper release if idle. Set to 0 to deactivate.
  783. // Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
  784. // Time can be set by M18 and M84.
  785. #define DEFAULT_STEPPER_DEACTIVE_TIME 120
  786. #define DISABLE_INACTIVE_X true
  787. #define DISABLE_INACTIVE_Y true
  788. #define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished.
  789. #define DISABLE_INACTIVE_E true
  790.  
  791. #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
  792. #define DEFAULT_MINTRAVELFEEDRATE 0.0
  793.  
  794. //#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
  795.  
  796. // Minimum time that a segment needs to take if the buffer is emptied
  797. #define DEFAULT_MINSEGMENTTIME 20000 // (µs)
  798.  
  799. // Slow down the machine if the look ahead buffer is (by default) half full.
  800. // Increase the slowdown divisor for larger buffer sizes.
  801. #define SLOWDOWN
  802. #if ENABLED(SLOWDOWN)
  803. #define SLOWDOWN_DIVISOR 2
  804. #endif
  805.  
  806. /**
  807. * XY Frequency limit
  808. * Reduce resonance by limiting the frequency of small zigzag infill moves.
  809. * See http://hydraraptor.blogspot.com/2010/12/frequency-limit.html
  810. * Use M201 F<freq> G<min%> to change limits at runtime.
  811. */
  812. //#define XY_FREQUENCY_LIMIT 10 // (Hz) Maximum frequency of small zigzag infill moves. Set with M201 F<hertz>.
  813. #ifdef XY_FREQUENCY_LIMIT
  814. #define XY_FREQUENCY_MIN_PERCENT 5 // (percent) Minimum FR percentage to apply. Set with M201 G<min%>.
  815. #endif
  816.  
  817. // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
  818. // of the buffer and all stops. This should not be much greater than zero and should only be changed
  819. // if unwanted behavior is observed on a user's machine when running at very slow speeds.
  820. #define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
  821.  
  822. //
  823. // Backlash Compensation
  824. // Adds extra movement to axes on direction-changes to account for backlash.
  825. //
  826. //#define BACKLASH_COMPENSATION
  827. #if ENABLED(BACKLASH_COMPENSATION)
  828. // Define values for backlash distance and correction.
  829. // If BACKLASH_GCODE is enabled these values are the defaults.
  830. #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm)
  831. #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction
  832.  
  833. // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments
  834. // to reduce print artifacts. (Enabling this is costly in memory and computation!)
  835. //#define BACKLASH_SMOOTHING_MM 3 // (mm)
  836.  
  837. // Add runtime configuration and tuning of backlash values (M425)
  838. //#define BACKLASH_GCODE
  839.  
  840. #if ENABLED(BACKLASH_GCODE)
  841. // Measure the Z backlash when probing (G29) and set with "M425 Z"
  842. #define MEASURE_BACKLASH_WHEN_PROBING
  843.  
  844. #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING)
  845. // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT
  846. // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION
  847. // increments while checking for the contact to be broken.
  848. #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm)
  849. #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm)
  850. #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m)
  851. #endif
  852. #endif
  853. #endif
  854.  
  855. /**
  856. * Automatic backlash, position and hotend offset calibration
  857. *
  858. * Enable G425 to run automatic calibration using an electrically-
  859. * conductive cube, bolt, or washer mounted on the bed.
  860. *
  861. * G425 uses the probe to touch the top and sides of the calibration object
  862. * on the bed and measures and/or correct positional offsets, axis backlash
  863. * and hotend offsets.
  864. *
  865. * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within
  866. * ±5mm of true values for G425 to succeed.
  867. */
  868. //#define CALIBRATION_GCODE
  869. #if ENABLED(CALIBRATION_GCODE)
  870.  
  871. #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm
  872.  
  873. #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m
  874. #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m
  875. #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m
  876.  
  877. // The following parameters refer to the conical section of the nozzle tip.
  878. #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
  879. #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
  880.  
  881. // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM).
  882. //#define CALIBRATION_REPORTING
  883.  
  884. // The true location and dimension the cube/bolt/washer on the bed.
  885. #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
  886. #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
  887.  
  888. // Comment out any sides which are unreachable by the probe. For best
  889. // auto-calibration results, all sides must be reachable.
  890. #define CALIBRATION_MEASURE_RIGHT
  891. #define CALIBRATION_MEASURE_FRONT
  892. #define CALIBRATION_MEASURE_LEFT
  893. #define CALIBRATION_MEASURE_BACK
  894.  
  895. // Probing at the exact top center only works if the center is flat. If
  896. // probing on a screwhead or hollow washer, probe near the edges.
  897. //#define CALIBRATION_MEASURE_AT_TOP_EDGES
  898.  
  899. // Define the pin to read during calibration
  900. #ifndef CALIBRATION_PIN
  901. //#define CALIBRATION_PIN -1 // Define here to override the default pin
  902. #define CALIBRATION_PIN_INVERTING false // Set to true to invert the custom pin
  903. //#define CALIBRATION_PIN_PULLDOWN
  904. #define CALIBRATION_PIN_PULLUP
  905. #endif
  906. #endif
  907.  
  908. /**
  909. * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies
  910. * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible
  911. * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the
  912. * lowest stepping frequencies.
  913. */
  914. //#define ADAPTIVE_STEP_SMOOTHING
  915.  
  916. /**
  917. * Custom Microstepping
  918. * Override as-needed for your setup. Up to 3 MS pins are supported.
  919. */
  920. //#define MICROSTEP1 LOW,LOW,LOW
  921. //#define MICROSTEP2 HIGH,LOW,LOW
  922. //#define MICROSTEP4 LOW,HIGH,LOW
  923. //#define MICROSTEP8 HIGH,HIGH,LOW
  924. //#define MICROSTEP16 LOW,LOW,HIGH
  925. //#define MICROSTEP32 HIGH,LOW,HIGH
  926.  
  927. // Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
  928. #define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
  929.  
  930. /**
  931. * @section stepper motor current
  932. *
  933. * Some boards have a means of setting the stepper motor current via firmware.
  934. *
  935. * The power on motor currents are set by:
  936. * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2
  937. * known compatible chips: A4982
  938. * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H
  939. * known compatible chips: AD5206
  940. * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
  941. * known compatible chips: MCP4728
  942. * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE
  943. * known compatible chips: MCP4451, MCP4018
  944. *
  945. * Motor currents can also be set by M907 - M910 and by the LCD.
  946. * M907 - applies to all.
  947. * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
  948. * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
  949. */
  950. //#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps
  951. //#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
  952. //#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
  953.  
  954. /**
  955. * I2C-based DIGIPOTs (e.g., Azteeg X3 Pro)
  956. */
  957. //#define DIGIPOT_MCP4018 // Requires https://github.com/stawel/SlowSoftI2CMaster
  958. //#define DIGIPOT_MCP4451
  959. #if EITHER(DIGIPOT_MCP4018, DIGIPOT_MCP4451)
  960. #define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT:4 AZTEEG_X3_PRO:8 MKS_SBASE:5 MIGHTYBOARD_REVE:5
  961.  
  962. // Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS.
  963. // These correspond to the physical drivers, so be mindful if the order is changed.
  964. #define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO
  965.  
  966. //#define DIGIPOT_USE_RAW_VALUES // Use DIGIPOT_MOTOR_CURRENT raw wiper values (instead of A4988 motor currents)
  967.  
  968. /**
  969. * Common slave addresses:
  970. *
  971. * A (A shifted) B (B shifted) IC
  972. * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451
  973. * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451
  974. * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451
  975. * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451
  976. * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018
  977. */
  978. //#define DIGIPOT_I2C_ADDRESS_A 0x2C // Unshifted slave address for first DIGIPOT
  979. //#define DIGIPOT_I2C_ADDRESS_B 0x2D // Unshifted slave address for second DIGIPOT
  980. #endif
  981.  
  982. //===========================================================================
  983. //=============================Additional Features===========================
  984. //===========================================================================
  985.  
  986. // @section lcd
  987.  
  988. #if EITHER(ULTIPANEL, EXTENSIBLE_UI)
  989. #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel
  990. #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
  991. #if ENABLED(ULTIPANEL)
  992. #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
  993. #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen
  994. #endif
  995. #endif
  996.  
  997. // Change values more rapidly when the encoder is rotated faster
  998. #define ENCODER_RATE_MULTIPLIER
  999. #if ENABLED(ENCODER_RATE_MULTIPLIER)
  1000. #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed
  1001. #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed
  1002. #endif
  1003.  
  1004. // Play a beep when the feedrate is changed from the Status Screen
  1005. //#define BEEP_ON_FEEDRATE_CHANGE
  1006. #if ENABLED(BEEP_ON_FEEDRATE_CHANGE)
  1007. #define FEEDRATE_CHANGE_BEEP_DURATION 10
  1008. #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440
  1009. #endif
  1010.  
  1011. #if HAS_LCD_MENU
  1012.  
  1013. // Include a page of printer information in the LCD Main Menu
  1014. #define LCD_INFO_MENU
  1015. #if ENABLED(LCD_INFO_MENU)
  1016. //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
  1017. #endif
  1018.  
  1019. // BACK menu items keep the highlight at the top
  1020. //#define TURBO_BACK_MENU_ITEM
  1021.  
  1022. /**
  1023. * LED Control Menu
  1024. * Add LED Control to the LCD menu
  1025. */
  1026. //#define LED_CONTROL_MENU
  1027. #if ENABLED(LED_CONTROL_MENU)
  1028. #define LED_COLOR_PRESETS // Enable the Preset Color menu option
  1029. #if ENABLED(LED_COLOR_PRESETS)
  1030. #define LED_USER_PRESET_RED 255 // User defined RED value
  1031. #define LED_USER_PRESET_GREEN 128 // User defined GREEN value
  1032. #define LED_USER_PRESET_BLUE 0 // User defined BLUE value
  1033. #define LED_USER_PRESET_WHITE 255 // User defined WHITE value
  1034. #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity
  1035. //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup
  1036. #endif
  1037. #endif
  1038.  
  1039. #endif // HAS_LCD_MENU
  1040.  
  1041. // Scroll a longer status message into view
  1042. #define STATUS_MESSAGE_SCROLLING
  1043.  
  1044. // On the Info Screen, display XY with one decimal place when possible
  1045. //#define LCD_DECIMAL_SMALL_XY
  1046.  
  1047. // The timeout (in ms) to return to the status screen from sub-menus
  1048. //#define LCD_TIMEOUT_TO_STATUS 15000
  1049.  
  1050. // Add an 'M73' G-code to set the current percentage
  1051. //#define LCD_SET_PROGRESS_MANUALLY
  1052.  
  1053. // Show the E position (filament used) during printing
  1054. //#define LCD_SHOW_E_TOTAL
  1055.  
  1056. #if ENABLED(SHOW_BOOTSCREEN)
  1057. #define BOOTSCREEN_TIMEOUT 4000 // (ms) Total Duration to display the boot screen(s)
  1058. #endif
  1059.  
  1060. #if HAS_GRAPHICAL_LCD && EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY)
  1061. //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
  1062. //#define SHOW_REMAINING_TIME // Display estimated time to completion
  1063. #if ENABLED(SHOW_REMAINING_TIME)
  1064. //#define USE_M73_REMAINING_TIME // Use remaining time from M73 command instead of estimation
  1065. //#define ROTATE_PROGRESS_DISPLAY // Display (P)rogress, (E)lapsed, and (R)emaining time
  1066. #endif
  1067. #endif
  1068.  
  1069. #if HAS_CHARACTER_LCD && EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY)
  1070. //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
  1071. #if ENABLED(LCD_PROGRESS_BAR)
  1072. #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar
  1073. #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message
  1074. #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever)
  1075. //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it
  1076. //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar
  1077. #endif
  1078. #endif
  1079.  
  1080. #if ENABLED(SDSUPPORT)
  1081.  
  1082. // The standard SD detect circuit reads LOW when media is inserted and HIGH when empty.
  1083. // Enable this option and set to HIGH if your SD cards are incorrectly detected.
  1084. //#define SD_DETECT_STATE HIGH
  1085.  
  1086. #define SD_PROCEDURE_DEPTH 1 // Increase if you need more nested M32 calls
  1087.  
  1088. #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
  1089. #define SD_FINISHED_RELEASECOMMAND "M84" // Use "M84XYE" to keep Z enabled so your bed stays in place
  1090.  
  1091. // Reverse SD sort to show "more recent" files first, according to the card's FAT.
  1092. // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
  1093. #define SDCARD_RATHERRECENTFIRST
  1094.  
  1095. #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing
  1096.  
  1097. //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files
  1098.  
  1099. #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27")
  1100.  
  1101. #if ENABLED(PRINTER_EVENT_LEDS)
  1102. #define PE_LEDS_COMPLETED_TIME (30*60) // (seconds) Time to keep the LED "done" color before restoring normal illumination
  1103. #endif
  1104.  
  1105. /**
  1106. * Continue after Power-Loss (Creality3D)
  1107. *
  1108. * Store the current state to the SD Card at the start of each layer
  1109. * during SD printing. If the recovery file is found at boot time, present
  1110. * an option on the LCD screen to continue the print from the last-known
  1111. * point in the file.
  1112. */
  1113. //#define POWER_LOSS_RECOVERY
  1114. #if ENABLED(POWER_LOSS_RECOVERY)
  1115. #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
  1116. //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
  1117. //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
  1118. //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
  1119. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
  1120. //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
  1121. //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
  1122. //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
  1123.  
  1124. // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
  1125. // especially with "vase mode" printing. Set too high and vases cannot be continued.
  1126. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
  1127. #endif
  1128.  
  1129. /**
  1130. * Sort SD file listings in alphabetical order.
  1131. *
  1132. * With this option enabled, items on SD cards will be sorted
  1133. * by name for easier navigation.
  1134. *
  1135. * By default...
  1136. *
  1137. * - Use the slowest -but safest- method for sorting.
  1138. * - Folders are sorted to the top.
  1139. * - The sort key is statically allocated.
  1140. * - No added G-code (M34) support.
  1141. * - 40 item sorting limit. (Items after the first 40 are unsorted.)
  1142. *
  1143. * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the
  1144. * compiler to calculate the worst-case usage and throw an error if the SRAM
  1145. * limit is exceeded.
  1146. *
  1147. * - SDSORT_USES_RAM provides faster sorting via a static directory buffer.
  1148. * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer.
  1149. * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
  1150. * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
  1151. */
  1152. //#define SDCARD_SORT_ALPHA
  1153.  
  1154. // SD Card Sorting options
  1155. #if ENABLED(SDCARD_SORT_ALPHA)
  1156. #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
  1157. #define FOLDER_SORTING -1 // -1=above 0=none 1=below
  1158. #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code.
  1159. #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
  1160. #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
  1161. #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
  1162. #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
  1163. #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
  1164. // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
  1165. #endif
  1166.  
  1167. // This allows hosts to request long names for files and folders with M33
  1168. //#define LONG_FILENAME_HOST_SUPPORT
  1169.  
  1170. // Enable this option to scroll long filenames in the SD card menu
  1171. #define SCROLL_LONG_FILENAMES
  1172.  
  1173. // Leave the heaters on after Stop Print (not recommended!)
  1174. //#define SD_ABORT_NO_COOLDOWN
  1175.  
  1176. /**
  1177. * This option allows you to abort SD printing when any endstop is triggered.
  1178. * This feature must be enabled with "M540 S1" or from the LCD menu.
  1179. * To have any effect, endstops must be enabled during SD printing.
  1180. */
  1181. //#define SD_ABORT_ON_ENDSTOP_HIT
  1182.  
  1183. /**
  1184. * This option makes it easier to print the same SD Card file again.
  1185. * On print completion the LCD Menu will open with the file selected.
  1186. * You can just click to start the print, or navigate elsewhere.
  1187. */
  1188. //#define SD_REPRINT_LAST_SELECTED_FILE
  1189.  
  1190. /**
  1191. * Auto-report SdCard status with M27 S<seconds>
  1192. */
  1193. //#define AUTO_REPORT_SD_STATUS
  1194.  
  1195. /**
  1196. * Support for USB thumb drives using an Arduino USB Host Shield or
  1197. * equivalent MAX3421E breakout board. The USB thumb drive will appear
  1198. * to Marlin as an SD card.
  1199. *
  1200. * The MAX3421E can be assigned the same pins as the SD card reader, with
  1201. * the following pin mapping:
  1202. *
  1203. * SCLK, MOSI, MISO --> SCLK, MOSI, MISO
  1204. * INT --> SD_DETECT_PIN [1]
  1205. * SS --> SDSS
  1206. *
  1207. * [1] On AVR an interrupt-capable pin is best for UHS3 compatibility.
  1208. */
  1209. //#define USB_FLASH_DRIVE_SUPPORT
  1210. #if ENABLED(USB_FLASH_DRIVE_SUPPORT)
  1211. #define USB_CS_PIN SDSS
  1212. #define USB_INTR_PIN SD_DETECT_PIN
  1213.  
  1214. /**
  1215. * USB Host Shield Library
  1216. *
  1217. * - UHS2 uses no interrupts and has been production-tested
  1218. * on a LulzBot TAZ Pro with a 32-bit Archim board.
  1219. *
  1220. * - UHS3 is newer code with better USB compatibility. But it
  1221. * is less tested and is known to interfere with Servos.
  1222. * [1] This requires USB_INTR_PIN to be interrupt-capable.
  1223. */
  1224. //#define USE_UHS3_USB
  1225. #endif
  1226.  
  1227. /**
  1228. * When using a bootloader that supports SD-Firmware-Flashing,
  1229. * add a menu item to activate SD-FW-Update on the next reboot.
  1230. *
  1231. * Requires ATMEGA2560 (Arduino Mega)
  1232. *
  1233. * Tested with this bootloader:
  1234. * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560
  1235. */
  1236. //#define SD_FIRMWARE_UPDATE
  1237. #if ENABLED(SD_FIRMWARE_UPDATE)
  1238. #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF
  1239. #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0
  1240. #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF
  1241. #endif
  1242.  
  1243. // Add an optimized binary file transfer mode, initiated with 'M28 B1'
  1244. //#define BINARY_FILE_TRANSFER
  1245.  
  1246. /**
  1247. * Set this option to one of the following (or the board's defaults apply):
  1248. *
  1249. * LCD - Use the SD drive in the external LCD controller.
  1250. * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.)
  1251. * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file).
  1252. *
  1253. * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
  1254. */
  1255. //#define SDCARD_CONNECTION LCD
  1256.  
  1257. #endif // SDSUPPORT
  1258.  
  1259. /**
  1260. * By default an onboard SD card reader may be shared as a USB mass-
  1261. * storage device. This option hides the SD card from the host PC.
  1262. */
  1263. //#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security).
  1264.  
  1265. /**
  1266. * Additional options for Graphical Displays
  1267. *
  1268. * Use the optimizations here to improve printing performance,
  1269. * which can be adversely affected by graphical display drawing,
  1270. * especially when doing several short moves, and when printing
  1271. * on DELTA and SCARA machines.
  1272. *
  1273. * Some of these options may result in the display lagging behind
  1274. * controller events, as there is a trade-off between reliable
  1275. * printing performance versus fast display updates.
  1276. */
  1277. #if HAS_GRAPHICAL_LCD
  1278. // Show SD percentage next to the progress bar
  1279. //#define DOGM_SD_PERCENT
  1280.  
  1281. // Save many cycles by drawing a hollow frame or no frame on the Info Screen
  1282. //#define XYZ_NO_FRAME
  1283. #define XYZ_HOLLOW_FRAME
  1284.  
  1285. // Enable to save many cycles by drawing a hollow frame on Menu Screens
  1286. #define MENU_HOLLOW_FRAME
  1287.  
  1288. // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
  1289. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  1290. //#define USE_BIG_EDIT_FONT
  1291.  
  1292. // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
  1293. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
  1294. //#define USE_SMALL_INFOFONT
  1295.  
  1296. // Swap the CW/CCW indicators in the graphics overlay
  1297. //#define OVERLAY_GFX_REVERSE
  1298.  
  1299. /**
  1300. * ST7920-based LCDs can emulate a 16 x 4 character display using
  1301. * the ST7920 character-generator for very fast screen updates.
  1302. * Enable LIGHTWEIGHT_UI to use this special display mode.
  1303. *
  1304. * Since LIGHTWEIGHT_UI has limited space, the position and status
  1305. * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the
  1306. * length of time to display the status message before clearing.
  1307. *
  1308. * Set STATUS_EXPIRE_SECONDS to zero to never clear the status.
  1309. * This will prevent position updates from being displayed.
  1310. */
  1311. #if ENABLED(U8GLIB_ST7920)
  1312. // Enable this option and reduce the value to optimize screen updates.
  1313. // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
  1314. //#define DOGM_SPI_DELAY_US 5
  1315.  
  1316. //#define LIGHTWEIGHT_UI
  1317. #if ENABLED(LIGHTWEIGHT_UI)
  1318. #define STATUS_EXPIRE_SECONDS 20
  1319. #endif
  1320. #endif
  1321.  
  1322. /**
  1323. * Status (Info) Screen customizations
  1324. * These options may affect code size and screen render time.
  1325. * Custom status screens can forcibly override these settings.
  1326. */
  1327. //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones
  1328. //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends)
  1329. #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM)
  1330. #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating
  1331. #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating
  1332. #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating
  1333. //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active
  1334. //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap
  1335. //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap
  1336. //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames
  1337. //#define STATUS_HEAT_PERCENT // Show heating in a progress bar
  1338. //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
  1339. //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
  1340.  
  1341. // Frivolous Game Options
  1342. //#define MARLIN_BRICKOUT
  1343. //#define MARLIN_INVADERS
  1344. //#define MARLIN_SNAKE
  1345. //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu
  1346.  
  1347. #endif // HAS_GRAPHICAL_LCD
  1348.  
  1349. //
  1350. // Additional options for DGUS / DWIN displays
  1351. //
  1352. #if HAS_DGUS_LCD
  1353. #define DGUS_SERIAL_PORT 3
  1354. #define DGUS_BAUDRATE 115200
  1355.  
  1356. #define DGUS_RX_BUFFER_SIZE 128
  1357. #define DGUS_TX_BUFFER_SIZE 48
  1358. //#define DGUS_SERIAL_STATS_RX_BUFFER_OVERRUNS // Fix Rx overrun situation (Currently only for AVR)
  1359.  
  1360. #define DGUS_UPDATE_INTERVAL_MS 500 // (ms) Interval between automatic screen updates
  1361.  
  1362. #if EITHER(DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_HIPRECY)
  1363. #define DGUS_PRINT_FILENAME // Display the filename during printing
  1364. #define DGUS_PREHEAT_UI // Display a preheat screen during heatup
  1365.  
  1366. #if ENABLED(DGUS_LCD_UI_FYSETC)
  1367. //#define DGUS_UI_MOVE_DIS_OPTION // Disabled by default for UI_FYSETC
  1368. #else
  1369. #define DGUS_UI_MOVE_DIS_OPTION // Enabled by default for UI_HIPRECY
  1370. #endif
  1371.  
  1372. #define DGUS_FILAMENT_LOADUNLOAD
  1373. #if ENABLED(DGUS_FILAMENT_LOADUNLOAD)
  1374. #define DGUS_FILAMENT_PURGE_LENGTH 10
  1375. #define DGUS_FILAMENT_LOAD_LENGTH_PER_TIME 0.5 // (mm) Adjust in proportion to DGUS_UPDATE_INTERVAL_MS
  1376. #endif
  1377.  
  1378. #define DGUS_UI_WAITING // Show a "waiting" screen between some screens
  1379. #if ENABLED(DGUS_UI_WAITING)
  1380. #define DGUS_UI_WAITING_STATUS 10
  1381. #define DGUS_UI_WAITING_STATUS_PERIOD 8 // Increase to slower waiting status looping
  1382. #endif
  1383. #endif
  1384. #endif // HAS_DGUS_LCD
  1385.  
  1386. //
  1387. // Touch UI for the FTDI Embedded Video Engine (EVE)
  1388. //
  1389. #if ENABLED(TOUCH_UI_FTDI_EVE)
  1390. // Display board used
  1391. //#define LCD_FTDI_VM800B35A // FTDI 3.5" with FT800 (320x240)
  1392. //#define LCD_4DSYSTEMS_4DLCD_FT843 // 4D Systems 4.3" (480x272)
  1393. //#define LCD_HAOYU_FT800CB // Haoyu with 4.3" or 5" (480x272)
  1394. //#define LCD_HAOYU_FT810CB // Haoyu with 5" (800x480)
  1395. //#define LCD_ALEPHOBJECTS_CLCD_UI // Aleph Objects Color LCD UI
  1396. //#define LCD_FYSETC_TFT81050 // FYSETC with 5" (800x480)
  1397.  
  1398. // Correct the resolution if not using the stock TFT panel.
  1399. //#define TOUCH_UI_320x240
  1400. //#define TOUCH_UI_480x272
  1401. //#define TOUCH_UI_800x480
  1402.  
  1403. // Mappings for boards with a standard RepRapDiscount Display connector
  1404. //#define AO_EXP1_PINMAP // AlephObjects CLCD UI EXP1 mapping
  1405. //#define AO_EXP2_PINMAP // AlephObjects CLCD UI EXP2 mapping
  1406. //#define CR10_TFT_PINMAP // Rudolph Riedel's CR10 pin mapping
  1407. //#define S6_TFT_PINMAP // FYSETC S6 pin mapping
  1408.  
  1409. //#define OTHER_PIN_LAYOUT // Define pins manually below
  1410. #if ENABLED(OTHER_PIN_LAYOUT)
  1411. // Pins for CS and MOD_RESET (PD) must be chosen
  1412. #define CLCD_MOD_RESET 9
  1413. #define CLCD_SPI_CS 10
  1414.  
  1415. // If using software SPI, specify pins for SCLK, MOSI, MISO
  1416. //#define CLCD_USE_SOFT_SPI
  1417. #if ENABLED(CLCD_USE_SOFT_SPI)
  1418. #define CLCD_SOFT_SPI_MOSI 11
  1419. #define CLCD_SOFT_SPI_MISO 12
  1420. #define CLCD_SOFT_SPI_SCLK 13
  1421. #endif
  1422. #endif
  1423.  
  1424. // Display Orientation. An inverted (i.e. upside-down) display
  1425. // is supported on the FT800. The FT810 and beyond also support
  1426. // portrait and mirrored orientations.
  1427. //#define TOUCH_UI_INVERTED
  1428. //#define TOUCH_UI_PORTRAIT
  1429. //#define TOUCH_UI_MIRRORED
  1430.  
  1431. // UTF8 processing and rendering.
  1432. // Unsupported characters are shown as '?'.
  1433. //#define TOUCH_UI_USE_UTF8
  1434. #if ENABLED(TOUCH_UI_USE_UTF8)
  1435. // Western accents support. These accented characters use
  1436. // combined bitmaps and require relatively little storage.
  1437. #define TOUCH_UI_UTF8_WESTERN_CHARSET
  1438. #if ENABLED(TOUCH_UI_UTF8_WESTERN_CHARSET)
  1439. // Additional character groups. These characters require
  1440. // full bitmaps and take up considerable storage:
  1441. //#define TOUCH_UI_UTF8_SUPERSCRIPTS // ¹ ² ³
  1442. //#define TOUCH_UI_UTF8_COPYRIGHT // © ®
  1443. //#define TOUCH_UI_UTF8_GERMANIC // ß
  1444. //#define TOUCH_UI_UTF8_SCANDINAVIAN // Æ Ð Ø Þ æ ð ø þ
  1445. //#define TOUCH_UI_UTF8_PUNCTUATION // « » ¿ ¡
  1446. //#define TOUCH_UI_UTF8_CURRENCY // ¢ £ ¤ ¥
  1447. //#define TOUCH_UI_UTF8_ORDINALS // º ª
  1448. //#define TOUCH_UI_UTF8_MATHEMATICS // ± × ÷
  1449. //#define TOUCH_UI_UTF8_FRACTIONS // ¼ ½ ¾
  1450. //#define TOUCH_UI_UTF8_SYMBOLS // µ ¶ ¦ § ¬
  1451. #endif
  1452. #endif
  1453.  
  1454. // Use a smaller font when labels don't fit buttons
  1455. #define TOUCH_UI_FIT_TEXT
  1456.  
  1457. // Allow language selection from menu at run-time (otherwise use LCD_LANGUAGE)
  1458. //#define LCD_LANGUAGE_1 en
  1459. //#define LCD_LANGUAGE_2 fr
  1460. //#define LCD_LANGUAGE_3 de
  1461. //#define LCD_LANGUAGE_4 es
  1462. //#define LCD_LANGUAGE_5 it
  1463.  
  1464. // Use a numeric passcode for "Screen lock" keypad.
  1465. // (recommended for smaller displays)
  1466. //#define TOUCH_UI_PASSCODE
  1467.  
  1468. // Output extra debug info for Touch UI events
  1469. //#define TOUCH_UI_DEBUG
  1470.  
  1471. // Developer menu (accessed by touching "About Printer" copyright text)
  1472. //#define TOUCH_UI_DEVELOPER_MENU
  1473. #endif
  1474.  
  1475. //
  1476. // FSMC Graphical TFT
  1477. //
  1478. #if ENABLED(FSMC_GRAPHICAL_TFT)
  1479. //#define TFT_MARLINUI_COLOR 0xFFFF // White
  1480. //#define TFT_MARLINBG_COLOR 0x0000 // Black
  1481. //#define TFT_DISABLED_COLOR 0x0003 // Almost black
  1482. //#define TFT_BTCANCEL_COLOR 0xF800 // Red
  1483. //#define TFT_BTARROWS_COLOR 0xDEE6 // 11011 110111 00110 Yellow
  1484. //#define TFT_BTOKMENU_COLOR 0x145F // 00010 100010 11111 Cyan
  1485. #endif
  1486.  
  1487. //
  1488. // ADC Button Debounce
  1489. //
  1490. #if HAS_ADC_BUTTONS
  1491. #define ADC_BUTTON_DEBOUNCE_DELAY 16 // (ms) Increase if buttons bounce or repeat too fast
  1492. #endif
  1493.  
  1494. // @section safety
  1495.  
  1496. /**
  1497. * The watchdog hardware timer will do a reset and disable all outputs
  1498. * if the firmware gets too overloaded to read the temperature sensors.
  1499. *
  1500. * If you find that watchdog reboot causes your AVR board to hang forever,
  1501. * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
  1502. * NOTE: This method is less reliable as it can only catch hangups while
  1503. * interrupts are enabled.
  1504. */
  1505. #define USE_WATCHDOG
  1506. #if ENABLED(USE_WATCHDOG)
  1507. //#define WATCHDOG_RESET_MANUAL
  1508. #endif
  1509.  
  1510. // @section lcd
  1511.  
  1512. /**
  1513. * Babystepping enables movement of the axes by tiny increments without changing
  1514. * the current position values. This feature is used primarily to adjust the Z
  1515. * axis in the first layer of a print in real-time.
  1516. *
  1517. * Warning: Does not respect endstops!
  1518. */
  1519. #define BABYSTEPPING
  1520. #if ENABLED(BABYSTEPPING)
  1521. //#define INTEGRATED_BABYSTEPPING // EXPERIMENTAL integration of babystepping into the Stepper ISR
  1522. //#define BABYSTEP_WITHOUT_HOMING
  1523. //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
  1524. #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
  1525. #define BABYSTEP_MULTIPLICATOR_Z 1 // Babysteps are very small. Increase for faster motion.
  1526. #define BABYSTEP_MULTIPLICATOR_XY 1
  1527.  
  1528. #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
  1529. #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
  1530. #define DOUBLECLICK_MAX_INTERVAL 2000 // Maximum interval between clicks, in milliseconds.
  1531. // Note: Extra time may be added to mitigate controller latency.
  1532. //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement).
  1533. //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle.
  1534. #if ENABLED(MOVE_Z_WHEN_IDLE)
  1535. #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size.
  1536. #endif
  1537. #endif
  1538.  
  1539. //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
  1540.  
  1541. //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
  1542. #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
  1543. //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
  1544. //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
  1545. #endif
  1546. #endif
  1547.  
  1548. // @section extruder
  1549.  
  1550. /**
  1551. * Linear Pressure Control v1.5
  1552. *
  1553. * Assumption: advance [steps] = k * (delta velocity [steps/s])
  1554. * K=0 means advance disabled.
  1555. *
  1556. * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions!
  1557. *
  1558. * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak.
  1559. * Larger K values will be needed for flexible filament and greater distances.
  1560. * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk)
  1561. * print acceleration will be reduced during the affected moves to keep within the limit.
  1562. *
  1563. * See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
  1564. */
  1565. //#define LIN_ADVANCE
  1566. #if ENABLED(LIN_ADVANCE)
  1567. //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
  1568. #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed
  1569. //#define LA_DEBUG // If enabled, this will generate debug information output over USB.
  1570. //#define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
  1571. #endif
  1572.  
  1573. // @section leveling
  1574.  
  1575. /**
  1576. * Points to probe for all 3-point Leveling procedures.
  1577. * Override if the automatically selected points are inadequate.
  1578. */
  1579. #if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
  1580. //#define PROBE_PT_1_X 15
  1581. //#define PROBE_PT_1_Y 180
  1582. //#define PROBE_PT_2_X 15
  1583. //#define PROBE_PT_2_Y 20
  1584. //#define PROBE_PT_3_X 170
  1585. //#define PROBE_PT_3_Y 20
  1586. #endif
  1587.  
  1588. /**
  1589. * Override MIN_PROBE_EDGE for each side of the build plate
  1590. * Useful to get probe points to exact positions on targets or
  1591. * to allow leveling to avoid plate clamps on only specific
  1592. * sides of the bed. With NOZZLE_AS_PROBE negative values are
  1593. * allowed, to permit probing outside the bed.
  1594. *
  1595. * If you are replacing the prior *_PROBE_BED_POSITION options,
  1596. * LEFT and FRONT values in most cases will map directly over
  1597. * RIGHT and REAR would be the inverse such as
  1598. * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
  1599. *
  1600. * This will allow all positions to match at compilation, however
  1601. * should the probe position be modified with M851XY then the
  1602. * probe points will follow. This prevents any change from causing
  1603. * the probe to be unable to reach any points.
  1604. */
  1605. constexpr int nozzle_to_probe_offset[] = NOZZLE_TO_PROBE_OFFSET;
  1606. #define PROBE_X_OFFSET_FROM_EXTRUDER nozzle_to_probe_offset[0]
  1607. #define PROBE_Y_OFFSET_FROM_EXTRUDER nozzle_to_probe_offset[1]
  1608.  
  1609. #if PROBE_SELECTED && !IS_KINEMATIC
  1610. #define MIN_PROBE_EDGE_LEFT (PROBE_X_OFFSET_FROM_EXTRUDER + MIN_PROBE_EDGE)
  1611. #define MIN_PROBE_EDGE_RIGHT (MIN_PROBE_EDGE)
  1612. #define MIN_PROBE_EDGE_FRONT (MIN_PROBE_EDGE)
  1613. #define MIN_PROBE_EDGE_BACK (MIN_PROBE_EDGE - PROBE_Y_OFFSET_FROM_EXTRUDER)
  1614. #endif
  1615.  
  1616. #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
  1617. // Override the mesh area if the automatic (max) area is too large
  1618. //#define MESH_MIN_X MESH_INSET
  1619. //#define MESH_MIN_Y MESH_INSET
  1620. //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
  1621. //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
  1622. #endif
  1623.  
  1624. /**
  1625. * Repeatedly attempt G29 leveling until it succeeds.
  1626. * Stop after G29_MAX_RETRIES attempts.
  1627. */
  1628. //#define G29_RETRY_AND_RECOVER
  1629. #if ENABLED(G29_RETRY_AND_RECOVER)
  1630. #define G29_MAX_RETRIES 3
  1631. #define G29_HALT_ON_FAILURE
  1632. /**
  1633. * Specify the GCODE commands that will be executed when leveling succeeds,
  1634. * between attempts, and after the maximum number of retries have been tried.
  1635. */
  1636. #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
  1637. #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
  1638. #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
  1639.  
  1640. #endif
  1641.  
  1642. /**
  1643. * Thermal Probe Compensation
  1644. * Probe measurements are adjusted to compensate for temperature distortion.
  1645. * Use G76 to calibrate this feature. Use M871 to set values manually.
  1646. * For a more detailed explanation of the process see G76_M871.cpp.
  1647. */
  1648. #if HAS_BED_PROBE && TEMP_SENSOR_PROBE && TEMP_SENSOR_BED
  1649. // Enable thermal first layer compensation using bed and probe temperatures
  1650. #define PROBE_TEMP_COMPENSATION
  1651.  
  1652. // Add additional compensation depending on hotend temperature
  1653. // Note: this values cannot be calibrated and have to be set manually
  1654. #if ENABLED(PROBE_TEMP_COMPENSATION)
  1655. // Park position to wait for probe cooldown
  1656. #define PTC_PARK_POS { 0, 0, 100 }
  1657.  
  1658. // Probe position to probe and wait for probe to reach target temperature
  1659. #define PTC_PROBE_POS { 90, 100 }
  1660.  
  1661. // Enable additional compensation using hotend temperature
  1662. // Note: this values cannot be calibrated automatically but have to be set manually
  1663. //#define USE_TEMP_EXT_COMPENSATION
  1664. #endif
  1665. #endif
  1666.  
  1667. // @section extras
  1668.  
  1669. //
  1670. // G60/G61 Position Save and Return
  1671. //
  1672. //#define SAVED_POSITIONS 1 // Each saved position slot costs 12 bytes
  1673.  
  1674. //
  1675. // G2/G3 Arc Support
  1676. //
  1677. #define ARC_SUPPORT // Disable this feature to save ~3226 bytes
  1678. #if ENABLED(ARC_SUPPORT)
  1679. #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment
  1680. //#define ARC_SEGMENTS_PER_R 1 // Max segment length, MM_PER = Min
  1681. #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle
  1682. //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum)
  1683. #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections
  1684. //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles
  1685. //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes
  1686. #endif
  1687.  
  1688. // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
  1689. //#define BEZIER_CURVE_SUPPORT
  1690.  
  1691. /**
  1692. * Direct Stepping
  1693. *
  1694. * Comparable to the method used by Klipper, G6 direct stepping significantly
  1695. * reduces motion calculations, increases top printing speeds, and results in
  1696. * less step aliasing by calculating all motions in advance.
  1697. * Preparing your G-code: https://github.com/colinrgodsey/step-daemon
  1698. */
  1699. //#define DIRECT_STEPPING
  1700.  
  1701. /**
  1702. * G38 Probe Target
  1703. *
  1704. * This option adds G38.2 and G38.3 (probe towards target)
  1705. * and optionally G38.4 and G38.5 (probe away from target).
  1706. * Set MULTIPLE_PROBING for G38 to probe more than once.
  1707. */
  1708. //#define G38_PROBE_TARGET
  1709. #if ENABLED(G38_PROBE_TARGET)
  1710. //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target
  1711. #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move.
  1712. #endif
  1713.  
  1714. // Moves (or segments) with fewer steps than this will be joined with the next move
  1715. #define MIN_STEPS_PER_SEGMENT 6
  1716.  
  1717. /**
  1718. * Minimum delay before and after setting the stepper DIR (in ns)
  1719. * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
  1720. * 20 : Minimum for TMC2xxx drivers
  1721. * 200 : Minimum for A4988 drivers
  1722. * 400 : Minimum for A5984 drivers
  1723. * 500 : Minimum for LV8729 drivers (guess, no info in datasheet)
  1724. * 650 : Minimum for DRV8825 drivers
  1725. * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
  1726. * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
  1727. *
  1728. * Override the default value based on the driver type set in Configuration.h.
  1729. */
  1730. //#define MINIMUM_STEPPER_POST_DIR_DELAY 650
  1731. //#define MINIMUM_STEPPER_PRE_DIR_DELAY 650
  1732.  
  1733. /**
  1734. * Minimum stepper driver pulse width (in µs)
  1735. * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
  1736. * 0 : Minimum 500ns for LV8729, adjusted in stepper.h
  1737. * 1 : Minimum for A4988 and A5984 stepper drivers
  1738. * 2 : Minimum for DRV8825 stepper drivers
  1739. * 3 : Minimum for TB6600 stepper drivers
  1740. * 30 : Minimum for TB6560 stepper drivers
  1741. *
  1742. * Override the default value based on the driver type set in Configuration.h.
  1743. */
  1744. //#define MINIMUM_STEPPER_PULSE 2
  1745.  
  1746. /**
  1747. * Maximum stepping rate (in Hz) the stepper driver allows
  1748. * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
  1749. * 5000000 : Maximum for TMC2xxx stepper drivers
  1750. * 1000000 : Maximum for LV8729 stepper driver
  1751. * 500000 : Maximum for A4988 stepper driver
  1752. * 250000 : Maximum for DRV8825 stepper driver
  1753. * 150000 : Maximum for TB6600 stepper driver
  1754. * 15000 : Maximum for TB6560 stepper driver
  1755. *
  1756. * Override the default value based on the driver type set in Configuration.h.
  1757. */
  1758. //#define MAXIMUM_STEPPER_RATE 250000
  1759.  
  1760. // @section temperature
  1761.  
  1762. // Control heater 0 and heater 1 in parallel.
  1763. //#define HEATERS_PARALLEL
  1764.  
  1765. //===========================================================================
  1766. //================================= Buffers =================================
  1767. //===========================================================================
  1768.  
  1769. // @section hidden
  1770.  
  1771. // The number of lineear moves that can be in the planner at once.
  1772. // The value of BLOCK_BUFFER_SIZE must be a power of 2 (e.g. 8, 16, 32)
  1773. #if BOTH(SDSUPPORT, DIRECT_STEPPING)
  1774. #define BLOCK_BUFFER_SIZE 8
  1775. #elif ENABLED(SDSUPPORT)
  1776. #define BLOCK_BUFFER_SIZE 16
  1777. #else
  1778. #define BLOCK_BUFFER_SIZE 16
  1779. #endif
  1780.  
  1781. // @section serial
  1782.  
  1783. // The ASCII buffer for serial input
  1784. #define MAX_CMD_SIZE 96
  1785. #define BUFSIZE 4
  1786.  
  1787. // Transmission to Host Buffer Size
  1788. // To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
  1789. // To buffer a simple "ok" you need 4 bytes.
  1790. // For ADVANCED_OK (M105) you need 32 bytes.
  1791. // For debug-echo: 128 bytes for the optimal speed.
  1792. // Other output doesn't need to be that speedy.
  1793. // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
  1794. #define TX_BUFFER_SIZE 0
  1795.  
  1796. // Host Receive Buffer Size
  1797. // Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
  1798. // To use flow control, set this buffer size to at least 1024 bytes.
  1799. // :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
  1800. //#define RX_BUFFER_SIZE 1024
  1801.  
  1802. #if RX_BUFFER_SIZE >= 1024
  1803. // Enable to have the controller send XON/XOFF control characters to
  1804. // the host to signal the RX buffer is becoming full.
  1805. //#define SERIAL_XON_XOFF
  1806. #endif
  1807.  
  1808. // Add M575 G-code to change the baud rate
  1809. //#define BAUD_RATE_GCODE
  1810.  
  1811. #if ENABLED(SDSUPPORT)
  1812. // Enable this option to collect and display the maximum
  1813. // RX queue usage after transferring a file to SD.
  1814. //#define SERIAL_STATS_MAX_RX_QUEUED
  1815.  
  1816. // Enable this option to collect and display the number
  1817. // of dropped bytes after a file transfer to SD.
  1818. //#define SERIAL_STATS_DROPPED_RX
  1819. #endif
  1820.  
  1821. /**
  1822. * Emergency Command Parser
  1823. *
  1824. * Add a low-level parser to intercept certain commands as they
  1825. * enter the serial receive buffer, so they cannot be blocked.
  1826. * Currently handles M108, M112, M410, M876
  1827. * NOTE: Not yet implemented for all platforms.
  1828. */
  1829. //#define EMERGENCY_PARSER
  1830.  
  1831. // Bad Serial-connections can miss a received command by sending an 'ok'
  1832. // Therefore some clients abort after 30 seconds in a timeout.
  1833. // Some other clients start sending commands while receiving a 'wait'.
  1834. // This "wait" is only sent when the buffer is empty. 1 second is a good value here.
  1835. //#define NO_TIMEOUTS 1000 // Milliseconds
  1836.  
  1837. // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
  1838. //#define ADVANCED_OK
  1839.  
  1840. // Printrun may have trouble receiving long strings all at once.
  1841. // This option inserts short delays between lines of serial output.
  1842. #define SERIAL_OVERRUN_PROTECTION
  1843.  
  1844. // @section extras
  1845.  
  1846. /**
  1847. * Extra Fan Speed
  1848. * Adds a secondary fan speed for each print-cooling fan.
  1849. * 'M106 P<fan> T3-255' : Set a secondary speed for <fan>
  1850. * 'M106 P<fan> T2' : Use the set secondary speed
  1851. * 'M106 P<fan> T1' : Restore the previous fan speed
  1852. */
  1853. //#define EXTRA_FAN_SPEED
  1854.  
  1855. /**
  1856. * Firmware-based and LCD-controlled retract
  1857. *
  1858. * Add G10 / G11 commands for automatic firmware-based retract / recover.
  1859. * Use M207 and M208 to define parameters for retract / recover.
  1860. *
  1861. * Use M209 to enable or disable auto-retract.
  1862. * With auto-retract enabled, all G1 E moves within the set range
  1863. * will be converted to firmware-based retract/recover moves.
  1864. *
  1865. * Be sure to turn off auto-retract during filament change.
  1866. *
  1867. * Note that M207 / M208 / M209 settings are saved to EEPROM.
  1868. *
  1869. */
  1870. //#define FWRETRACT
  1871. #if ENABLED(FWRETRACT)
  1872. #define FWRETRACT_AUTORETRACT // Override slicer retractions
  1873. #if ENABLED(FWRETRACT_AUTORETRACT)
  1874. #define MIN_AUTORETRACT 0.1 // (mm) Don't convert E moves under this length
  1875. #define MAX_AUTORETRACT 10.0 // (mm) Don't convert E moves over this length
  1876. #endif
  1877. #define RETRACT_LENGTH 3 // (mm) Default retract length (positive value)
  1878. #define RETRACT_LENGTH_SWAP 13 // (mm) Default swap retract length (positive value)
  1879. #define RETRACT_FEEDRATE 45 // (mm/s) Default feedrate for retracting
  1880. #define RETRACT_ZRAISE 0 // (mm) Default retract Z-raise
  1881. #define RETRACT_RECOVER_LENGTH 0 // (mm) Default additional recover length (added to retract length on recover)
  1882. #define RETRACT_RECOVER_LENGTH_SWAP 0 // (mm) Default additional swap recover length (added to retract length on recover from toolchange)
  1883. #define RETRACT_RECOVER_FEEDRATE 8 // (mm/s) Default feedrate for recovering from retraction
  1884. #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // (mm/s) Default feedrate for recovering from swap retraction
  1885. #if ENABLED(MIXING_EXTRUDER)
  1886. //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously
  1887. #endif
  1888. #endif
  1889.  
  1890. /**
  1891. * Universal tool change settings.
  1892. * Applies to all types of extruders except where explicitly noted.
  1893. */
  1894. #if EXTRUDERS > 1
  1895. // Z raise distance for tool-change, as needed for some extruders
  1896. #define TOOLCHANGE_ZRAISE 2 // (mm)
  1897. //#define TOOLCHANGE_ZRAISE_BEFORE_RETRACT // Apply raise before swap retraction (if enabled)
  1898. //#define TOOLCHANGE_NO_RETURN // Never return to previous position on tool-change
  1899. #if ENABLED(TOOLCHANGE_NO_RETURN)
  1900. //#define EVENT_GCODE_AFTER_TOOLCHANGE "G12X" // Extra G-code to run after tool-change
  1901. #endif
  1902.  
  1903. /**
  1904. * Retract and prime filament on tool-change to reduce
  1905. * ooze and stringing and to get cleaner transitions.
  1906. */
  1907. //#define TOOLCHANGE_FILAMENT_SWAP
  1908. #if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
  1909. // Load / Unload
  1910. #define TOOLCHANGE_FS_LENGTH 12 // (mm) Load / Unload length
  1911. #define TOOLCHANGE_FS_EXTRA_RESUME_LENGTH 0 // (mm) Extra length for better restart, fine tune by LCD/Gcode)
  1912. #define TOOLCHANGE_FS_RETRACT_SPEED (50*60) // (mm/m) (Unloading)
  1913. #define TOOLCHANGE_FS_UNRETRACT_SPEED (25*60) // (mm/m) (On SINGLENOZZLE or Bowden loading must be slowed down)
  1914.  
  1915. // Longer prime to clean out a SINGLENOZZLE
  1916. #define TOOLCHANGE_FS_EXTRA_PRIME 0 // (mm) Extra priming length
  1917. #define TOOLCHANGE_FS_PRIME_SPEED (4.6*60) // (mm/m) Extra priming feedrate
  1918. #define TOOLCHANGE_FS_WIPE_RETRACT 0 // (mm/m) Retract before cooling for less stringing, better wipe, etc.
  1919.  
  1920. // Cool after prime to reduce stringing
  1921. #define TOOLCHANGE_FS_FAN -1 // Fan index or -1 to skip
  1922. #define TOOLCHANGE_FS_FAN_SPEED 255 // 0-255
  1923. #define TOOLCHANGE_FS_FAN_TIME 10 // (seconds)
  1924.  
  1925. // Swap uninitialized extruder with TOOLCHANGE_FS_PRIME_SPEED for all lengths (recover + prime)
  1926. // (May break filament if not retracted beforehand.)
  1927. //#define TOOLCHANGE_FS_INIT_BEFORE_SWAP
  1928.  
  1929. // Prime on the first T0 (If other, TOOLCHANGE_FS_INIT_BEFORE_SWAP applied)
  1930. // Enable it (M217 V[0/1]) before printing, to avoid unwanted priming on host connect
  1931. //#define TOOLCHANGE_FS_PRIME_FIRST_USED
  1932.  
  1933. /**
  1934. * Tool Change Migration
  1935. * This feature provides G-code and LCD options to switch tools mid-print.
  1936. * All applicable tool properties are migrated so the print can continue.
  1937. * Tools must be closely matching and other restrictions may apply.
  1938. * Useful to:
  1939. * - Change filament color without interruption
  1940. * - Switch spools automatically on filament runout
  1941. * - Switch to a different nozzle on an extruder jam
  1942. */
  1943. #define TOOLCHANGE_MIGRATION_FEATURE
  1944.  
  1945. #endif
  1946.  
  1947. /**
  1948. * Position to park head during tool change.
  1949. * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER
  1950. */
  1951. //#define TOOLCHANGE_PARK
  1952. #if ENABLED(TOOLCHANGE_PARK)
  1953. #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 }
  1954. #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m)
  1955. //#define TOOLCHANGE_PARK_X_ONLY // X axis only move
  1956. //#define TOOLCHANGE_PARK_Y_ONLY // Y axis only move
  1957. #endif
  1958. #endif // EXTRUDERS > 1
  1959.  
  1960. /**
  1961. * Advanced Pause
  1962. * Experimental feature for filament change support and for parking the nozzle when paused.
  1963. * Adds the GCode M600 for initiating filament change.
  1964. * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle.
  1965. *
  1966. * Requires an LCD display.
  1967. * Requires NOZZLE_PARK_FEATURE.
  1968. * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  1969. */
  1970. //#define ADVANCED_PAUSE_FEATURE
  1971. #if ENABLED(ADVANCED_PAUSE_FEATURE)
  1972. #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
  1973. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
  1974. // This short retract is done immediately, before parking the nozzle.
  1975. #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
  1976. #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
  1977. #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
  1978. // For Bowden, the full length of the tube and nozzle.
  1979. // For direct drive, the full length of the nozzle.
  1980. // Set to 0 for manual unloading.
  1981. #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
  1982. #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
  1983. // 0 to disable start loading and skip to fast load only
  1984. #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
  1985. #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
  1986. #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
  1987. // For Bowden, the full length of the tube and nozzle.
  1988. // For direct drive, the full length of the nozzle.
  1989. //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
  1990. #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
  1991. #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
  1992. // Set to 0 for manual extrusion.
  1993. // Filament can be extruded repeatedly from the Filament Change menu
  1994. // until extrusion is consistent, and to purge old filament.
  1995. #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park.
  1996. //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused.
  1997.  
  1998. // Filament Unload does a Retract, Delay, and Purge first:
  1999. #define FILAMENT_UNLOAD_PURGE_RETRACT 13 // (mm) Unload initial retract length.
  2000. #define FILAMENT_UNLOAD_PURGE_DELAY 5000 // (ms) Delay for the filament to cool after retract.
  2001. #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
  2002. #define FILAMENT_UNLOAD_PURGE_FEEDRATE 25 // (mm/s) feedrate to purge before unload
  2003.  
  2004. #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
  2005. #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
  2006. #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
  2007.  
  2008. //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
  2009. //#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
  2010.  
  2011. //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
  2012. //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
  2013. #endif
  2014.  
  2015. // @section tmc
  2016.  
  2017. /**
  2018. * TMC26X Stepper Driver options
  2019. *
  2020. * The TMC26XStepper library is required for this stepper driver.
  2021. * https://github.com/trinamic/TMC26XStepper
  2022. */
  2023. #if HAS_DRIVER(TMC26X)
  2024.  
  2025. #if AXIS_DRIVER_TYPE_X(TMC26X)
  2026. #define X_MAX_CURRENT 1000 // (mA)
  2027. #define X_SENSE_RESISTOR 91 // (mOhms)
  2028. #define X_MICROSTEPS 16 // Number of microsteps
  2029. #endif
  2030.  
  2031. #if AXIS_DRIVER_TYPE_X2(TMC26X)
  2032. #define X2_MAX_CURRENT 1000
  2033. #define X2_SENSE_RESISTOR 91
  2034. #define X2_MICROSTEPS 16
  2035. #endif
  2036.  
  2037. #if AXIS_DRIVER_TYPE_Y(TMC26X)
  2038. #define Y_MAX_CURRENT 1000
  2039. #define Y_SENSE_RESISTOR 91
  2040. #define Y_MICROSTEPS 16
  2041. #endif
  2042.  
  2043. #if AXIS_DRIVER_TYPE_Y2(TMC26X)
  2044. #define Y2_MAX_CURRENT 1000
  2045. #define Y2_SENSE_RESISTOR 91
  2046. #define Y2_MICROSTEPS 16
  2047. #endif
  2048.  
  2049. #if AXIS_DRIVER_TYPE_Z(TMC26X)
  2050. #define Z_MAX_CURRENT 1000
  2051. #define Z_SENSE_RESISTOR 91
  2052. #define Z_MICROSTEPS 16
  2053. #endif
  2054.  
  2055. #if AXIS_DRIVER_TYPE_Z2(TMC26X)
  2056. #define Z2_MAX_CURRENT 1000
  2057. #define Z2_SENSE_RESISTOR 91
  2058. #define Z2_MICROSTEPS 16
  2059. #endif
  2060.  
  2061. #if AXIS_DRIVER_TYPE_Z3(TMC26X)
  2062. #define Z3_MAX_CURRENT 1000
  2063. #define Z3_SENSE_RESISTOR 91
  2064. #define Z3_MICROSTEPS 16
  2065. #endif
  2066.  
  2067. #if AXIS_DRIVER_TYPE_Z4(TMC26X)
  2068. #define Z4_MAX_CURRENT 1000
  2069. #define Z4_SENSE_RESISTOR 91
  2070. #define Z4_MICROSTEPS 16
  2071. #endif
  2072.  
  2073. #if AXIS_DRIVER_TYPE_E0(TMC26X)
  2074. #define E0_MAX_CURRENT 1000
  2075. #define E0_SENSE_RESISTOR 91
  2076. #define E0_MICROSTEPS 16
  2077. #endif
  2078.  
  2079. #if AXIS_DRIVER_TYPE_E1(TMC26X)
  2080. #define E1_MAX_CURRENT 1000
  2081. #define E1_SENSE_RESISTOR 91
  2082. #define E1_MICROSTEPS 16
  2083. #endif
  2084.  
  2085. #if AXIS_DRIVER_TYPE_E2(TMC26X)
  2086. #define E2_MAX_CURRENT 1000
  2087. #define E2_SENSE_RESISTOR 91
  2088. #define E2_MICROSTEPS 16
  2089. #endif
  2090.  
  2091. #if AXIS_DRIVER_TYPE_E3(TMC26X)
  2092. #define E3_MAX_CURRENT 1000
  2093. #define E3_SENSE_RESISTOR 91
  2094. #define E3_MICROSTEPS 16
  2095. #endif
  2096.  
  2097. #if AXIS_DRIVER_TYPE_E4(TMC26X)
  2098. #define E4_MAX_CURRENT 1000
  2099. #define E4_SENSE_RESISTOR 91
  2100. #define E4_MICROSTEPS 16
  2101. #endif
  2102.  
  2103. #if AXIS_DRIVER_TYPE_E5(TMC26X)
  2104. #define E5_MAX_CURRENT 1000
  2105. #define E5_SENSE_RESISTOR 91
  2106. #define E5_MICROSTEPS 16
  2107. #endif
  2108.  
  2109. #if AXIS_DRIVER_TYPE_E6(TMC26X)
  2110. #define E6_MAX_CURRENT 1000
  2111. #define E6_SENSE_RESISTOR 91
  2112. #define E6_MICROSTEPS 16
  2113. #endif
  2114.  
  2115. #if AXIS_DRIVER_TYPE_E7(TMC26X)
  2116. #define E7_MAX_CURRENT 1000
  2117. #define E7_SENSE_RESISTOR 91
  2118. #define E7_MICROSTEPS 16
  2119. #endif
  2120.  
  2121. #endif // TMC26X
  2122.  
  2123. // @section tmc_smart
  2124.  
  2125. /**
  2126. * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode
  2127. * connect your SPI pins to the hardware SPI interface on your board and define
  2128. * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3
  2129. * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
  2130. * You may also use software SPI if you wish to use general purpose IO pins.
  2131. *
  2132. * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN
  2133. * to the driver side PDN_UART pin with a 1K resistor.
  2134. * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without
  2135. * a resistor.
  2136. * The drivers can also be used with hardware serial.
  2137. *
  2138. * TMCStepper library is required to use TMC stepper drivers.
  2139. * https://github.com/teemuatlut/TMCStepper
  2140. */
  2141. #if HAS_TRINAMIC_CONFIG
  2142.  
  2143. #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
  2144. #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256
  2145.  
  2146. #if AXIS_IS_TMC(X)
  2147. #define X_CURRENT 760 // (mA) RMS current. Multiply by 1.414 for peak current.
  2148. #define X_CURRENT_HOME X_CURRENT // (mA) RMS current for sensorless homing
  2149. #define X_MICROSTEPS 16 // 0..256
  2150. #define X_RSENSE 0.075
  2151. #define X_CHAIN_POS -1 // <=0 : Not chained. 1 : MCU MOSI connected. 2 : Next in chain, ...
  2152. #endif
  2153.  
  2154. #if AXIS_IS_TMC(X2)
  2155. #define X2_CURRENT 800
  2156. #define X2_CURRENT_HOME X2_CURRENT
  2157. #define X2_MICROSTEPS 16
  2158. #define X2_RSENSE 0.11
  2159. #define X2_CHAIN_POS -1
  2160. #endif
  2161.  
  2162. #if AXIS_IS_TMC(Y)
  2163. #define Y_CURRENT 760
  2164. #define Y_CURRENT_HOME Y_CURRENT
  2165. #define Y_MICROSTEPS 16
  2166. #define Y_RSENSE 0.075
  2167. #define Y_CHAIN_POS -1
  2168. #endif
  2169.  
  2170. #if AXIS_IS_TMC(Y2)
  2171. #define Y2_CURRENT 800
  2172. #define Y2_CURRENT_HOME Y2_CURRENT
  2173. #define Y2_MICROSTEPS 16
  2174. #define Y2_RSENSE 0.11
  2175. #define Y2_CHAIN_POS -1
  2176. #endif
  2177.  
  2178. #if AXIS_IS_TMC(Z)
  2179. #define Z_CURRENT 760
  2180. #define Z_CURRENT_HOME Z_CURRENT
  2181. #define Z_MICROSTEPS 16
  2182. #define Z_RSENSE 0.075
  2183. #define Z_CHAIN_POS -1
  2184. #endif
  2185.  
  2186. #if AXIS_IS_TMC(Z2)
  2187. #define Z2_CURRENT 800
  2188. #define Z2_CURRENT_HOME Z2_CURRENT
  2189. #define Z2_MICROSTEPS 16
  2190. #define Z2_RSENSE 0.11
  2191. #define Z2_CHAIN_POS -1
  2192. #endif
  2193.  
  2194. #if AXIS_IS_TMC(Z3)
  2195. #define Z3_CURRENT 800
  2196. #define Z3_CURRENT_HOME Z3_CURRENT
  2197. #define Z3_MICROSTEPS 16
  2198. #define Z3_RSENSE 0.11
  2199. #define Z3_CHAIN_POS -1
  2200. #endif
  2201.  
  2202. #if AXIS_IS_TMC(Z4)
  2203. #define Z4_CURRENT 800
  2204. #define Z4_CURRENT_HOME Z4_CURRENT
  2205. #define Z4_MICROSTEPS 16
  2206. #define Z4_RSENSE 0.11
  2207. #define Z4_CHAIN_POS -1
  2208. #endif
  2209.  
  2210. #if AXIS_IS_TMC(E0)
  2211. #define E0_CURRENT 900
  2212. #define E0_MICROSTEPS 16
  2213. #define E0_RSENSE 0.075
  2214. #define E0_CHAIN_POS -1
  2215. #endif
  2216.  
  2217. #if AXIS_IS_TMC(E1)
  2218. #define E1_CURRENT 800
  2219. #define E1_MICROSTEPS 16
  2220. #define E1_RSENSE 0.11
  2221. #define E1_CHAIN_POS -1
  2222. #endif
  2223.  
  2224. #if AXIS_IS_TMC(E2)
  2225. #define E2_CURRENT 800
  2226. #define E2_MICROSTEPS 16
  2227. #define E2_RSENSE 0.11
  2228. #define E2_CHAIN_POS -1
  2229. #endif
  2230.  
  2231. #if AXIS_IS_TMC(E3)
  2232. #define E3_CURRENT 800
  2233. #define E3_MICROSTEPS 16
  2234. #define E3_RSENSE 0.11
  2235. #define E3_CHAIN_POS -1
  2236. #endif
  2237.  
  2238. #if AXIS_IS_TMC(E4)
  2239. #define E4_CURRENT 800
  2240. #define E4_MICROSTEPS 16
  2241. #define E4_RSENSE 0.11
  2242. #define E4_CHAIN_POS -1
  2243. #endif
  2244.  
  2245. #if AXIS_IS_TMC(E5)
  2246. #define E5_CURRENT 800
  2247. #define E5_MICROSTEPS 16
  2248. #define E5_RSENSE 0.11
  2249. #define E5_CHAIN_POS -1
  2250. #endif
  2251.  
  2252. #if AXIS_IS_TMC(E6)
  2253. #define E6_CURRENT 800
  2254. #define E6_MICROSTEPS 16
  2255. #define E6_RSENSE 0.11
  2256. #define E6_CHAIN_POS -1
  2257. #endif
  2258.  
  2259. #if AXIS_IS_TMC(E7)
  2260. #define E7_CURRENT 800
  2261. #define E7_MICROSTEPS 16
  2262. #define E7_RSENSE 0.11
  2263. #define E7_CHAIN_POS -1
  2264. #endif
  2265.  
  2266. /**
  2267. * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here.
  2268. * The default pins can be found in your board's pins file.
  2269. */
  2270. //#define X_CS_PIN -1
  2271. //#define Y_CS_PIN -1
  2272. //#define Z_CS_PIN -1
  2273. //#define X2_CS_PIN -1
  2274. //#define Y2_CS_PIN -1
  2275. //#define Z2_CS_PIN -1
  2276. //#define Z3_CS_PIN -1
  2277. //#define E0_CS_PIN -1
  2278. //#define E1_CS_PIN -1
  2279. //#define E2_CS_PIN -1
  2280. //#define E3_CS_PIN -1
  2281. //#define E4_CS_PIN -1
  2282. //#define E5_CS_PIN -1
  2283. //#define E6_CS_PIN -1
  2284. //#define E7_CS_PIN -1
  2285.  
  2286. /**
  2287. * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160).
  2288. * The default SW SPI pins are defined the respective pins files,
  2289. * but you can override or define them here.
  2290. */
  2291. #define TMC_USE_SW_SPI
  2292. //#define TMC_SW_MOSI -1
  2293. //#define TMC_SW_MISO -1
  2294. //#define TMC_SW_SCK -1
  2295.  
  2296. /**
  2297. * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses.
  2298. * Set the address using jumpers on pins MS1 and MS2.
  2299. * Address | MS1 | MS2
  2300. * 0 | LOW | LOW
  2301. * 1 | HIGH | LOW
  2302. * 2 | LOW | HIGH
  2303. * 3 | HIGH | HIGH
  2304. *
  2305. * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers
  2306. * on the same serial port, either here or in your board's pins file.
  2307. */
  2308. #define X_SLAVE_ADDRESS 0
  2309. #define Y_SLAVE_ADDRESS 0
  2310. #define Z_SLAVE_ADDRESS 0
  2311. #define X2_SLAVE_ADDRESS 0
  2312. #define Y2_SLAVE_ADDRESS 0
  2313. #define Z2_SLAVE_ADDRESS 0
  2314. #define Z3_SLAVE_ADDRESS 0
  2315. #define Z4_SLAVE_ADDRESS 0
  2316. #define E0_SLAVE_ADDRESS 0
  2317. #define E1_SLAVE_ADDRESS 0
  2318. #define E2_SLAVE_ADDRESS 0
  2319. #define E3_SLAVE_ADDRESS 0
  2320. #define E4_SLAVE_ADDRESS 0
  2321. #define E5_SLAVE_ADDRESS 0
  2322. #define E6_SLAVE_ADDRESS 0
  2323. #define E7_SLAVE_ADDRESS 0
  2324.  
  2325. /**
  2326. * Software enable
  2327. *
  2328. * Use for drivers that do not use a dedicated enable pin, but rather handle the same
  2329. * function through a communication line such as SPI or UART.
  2330. */
  2331. //#define SOFTWARE_DRIVER_ENABLE
  2332.  
  2333. /**
  2334. * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
  2335. * Use Trinamic's ultra quiet stepping mode.
  2336. * When disabled, Marlin will use spreadCycle stepping mode.
  2337. */
  2338. #define STEALTHCHOP_XY
  2339. #define STEALTHCHOP_Z
  2340. #define STEALTHCHOP_E
  2341.  
  2342. /**
  2343. * Optimize spreadCycle chopper parameters by using predefined parameter sets
  2344. * or with the help of an example included in the library.
  2345. * Provided parameter sets are
  2346. * CHOPPER_DEFAULT_12V
  2347. * CHOPPER_DEFAULT_19V
  2348. * CHOPPER_DEFAULT_24V
  2349. * CHOPPER_DEFAULT_36V
  2350. * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V)
  2351. * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9
  2352. *
  2353. * Define you own with
  2354. * { <off_time[1..15]>, <hysteresis_end[-3..12]>, hysteresis_start[1..8] }
  2355. */
  2356. #define CHOPPER_TIMING CHOPPER_DEFAULT_24V
  2357.  
  2358. /**
  2359. * Monitor Trinamic drivers
  2360. * for error conditions like overtemperature and short to ground.
  2361. * To manage over-temp Marlin can decrease the driver current until the error condition clears.
  2362. * Other detected conditions can be used to stop the current print.
  2363. * Relevant g-codes:
  2364. * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given.
  2365. * M911 - Report stepper driver overtemperature pre-warn condition.
  2366. * M912 - Clear stepper driver overtemperature pre-warn condition flag.
  2367. * M122 - Report driver parameters (Requires TMC_DEBUG)
  2368. */
  2369. #define MONITOR_DRIVER_STATUS
  2370.  
  2371. #if ENABLED(MONITOR_DRIVER_STATUS)
  2372. #define CURRENT_STEP_DOWN 50 // [mA]
  2373. #define REPORT_CURRENT_CHANGE
  2374. #define STOP_ON_ERROR
  2375. #endif
  2376.  
  2377. /**
  2378. * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
  2379. * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
  2380. * This mode allows for faster movements at the expense of higher noise levels.
  2381. * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
  2382. * M913 X/Y/Z/E to live tune the setting
  2383. */
  2384. #define HYBRID_THRESHOLD
  2385.  
  2386. #define X_HYBRID_THRESHOLD 100 // [mm/s]
  2387. #define X2_HYBRID_THRESHOLD 100
  2388. #define Y_HYBRID_THRESHOLD 100
  2389. #define Y2_HYBRID_THRESHOLD 100
  2390. #define Z_HYBRID_THRESHOLD 3
  2391. #define Z2_HYBRID_THRESHOLD 3
  2392. #define Z3_HYBRID_THRESHOLD 3
  2393. #define Z4_HYBRID_THRESHOLD 3
  2394. #define E0_HYBRID_THRESHOLD 30
  2395. #define E1_HYBRID_THRESHOLD 30
  2396. #define E2_HYBRID_THRESHOLD 30
  2397. #define E3_HYBRID_THRESHOLD 30
  2398. #define E4_HYBRID_THRESHOLD 30
  2399. #define E5_HYBRID_THRESHOLD 30
  2400. #define E6_HYBRID_THRESHOLD 30
  2401. #define E7_HYBRID_THRESHOLD 30
  2402.  
  2403. /**
  2404. * Use StallGuard2 to home / probe X, Y, Z.
  2405. *
  2406. * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only
  2407. * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
  2408. * X, Y, and Z homing will always be done in spreadCycle mode.
  2409. *
  2410. * X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
  2411. * Use M914 X Y Z to set the stall threshold at runtime:
  2412. *
  2413. * Sensitivity TMC2209 Others
  2414. * HIGHEST 255 -64 (Too sensitive => False positive)
  2415. * LOWEST 0 63 (Too insensitive => No trigger)
  2416. *
  2417. * It is recommended to set HOMING_BUMP_MM to { 0, 0, 0 }.
  2418. *
  2419. * SPI_ENDSTOPS *** Beta feature! *** TMC2130 Only ***
  2420. * Poll the driver through SPI to determine load when homing.
  2421. * Removes the need for a wire from DIAG1 to an endstop pin.
  2422. *
  2423. * IMPROVE_HOMING_RELIABILITY tunes acceleration and jerk when
  2424. * homing and adds a guard period for endstop triggering.
  2425. */
  2426. //#define SENSORLESS_HOMING // StallGuard capable drivers only
  2427.  
  2428. #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING)
  2429. // TMC2209: 0...255. TMC2130: -64...63
  2430. #define X_STALL_SENSITIVITY 8
  2431. #define X2_STALL_SENSITIVITY X_STALL_SENSITIVITY
  2432. #define Y_STALL_SENSITIVITY 8
  2433. #define Y2_STALL_SENSITIVITY Y_STALL_SENSITIVITY
  2434. //#define Z_STALL_SENSITIVITY 8
  2435. //#define Z2_STALL_SENSITIVITY Z_STALL_SENSITIVITY
  2436. //#define Z3_STALL_SENSITIVITY Z_STALL_SENSITIVITY
  2437. //#define Z4_STALL_SENSITIVITY Z_STALL_SENSITIVITY
  2438. //#define SPI_ENDSTOPS // TMC2130 only
  2439. //#define IMPROVE_HOMING_RELIABILITY
  2440. #endif
  2441.  
  2442. /**
  2443. * TMC Homing stepper phase.
  2444. *
  2445. * Improve homing repeatability by homing to stepper coil's nearest absolute
  2446. * phase position. Trinamic drivers use a stepper phase table with 1024 values
  2447. * spanning 4 full steps with 256 positions each (ergo, 1024 positions).
  2448. * Full step positions (128, 384, 640, 896) have the highest holding torque.
  2449. *
  2450. * Values from 0..1023, -1 to disable homing phase for that axis.
  2451. */
  2452. //#define TMC_HOME_PHASE { 896, 896, 896 }
  2453.  
  2454. /**
  2455. * Beta feature!
  2456. * Create a 50/50 square wave step pulse optimal for stepper drivers.
  2457. */
  2458. //#define SQUARE_WAVE_STEPPING
  2459.  
  2460. /**
  2461. * Enable M122 debugging command for TMC stepper drivers.
  2462. * M122 S0/1 will enable continous reporting.
  2463. */
  2464. #define TMC_DEBUG
  2465.  
  2466. /**
  2467. * You can set your own advanced settings by filling in predefined functions.
  2468. * A list of available functions can be found on the library github page
  2469. * https://github.com/teemuatlut/TMCStepper
  2470. *
  2471. * Example:
  2472. * #define TMC_ADV() { \
  2473. * stepperX.diag0_otpw(1); \
  2474. * stepperY.intpol(0); \
  2475. * }
  2476. */
  2477. #define TMC_ADV() { }
  2478.  
  2479. #endif // HAS_TRINAMIC_CONFIG
  2480.  
  2481. // @section L64XX
  2482.  
  2483. /**
  2484. * L64XX Stepper Driver options
  2485. *
  2486. * Arduino-L6470 library (0.8.0 or higher) is required.
  2487. * https://github.com/ameyer/Arduino-L6470
  2488. *
  2489. * Requires the following to be defined in your pins_YOUR_BOARD file
  2490. * L6470_CHAIN_SCK_PIN
  2491. * L6470_CHAIN_MISO_PIN
  2492. * L6470_CHAIN_MOSI_PIN
  2493. * L6470_CHAIN_SS_PIN
  2494. * ENABLE_RESET_L64XX_CHIPS(Q) where Q is 1 to enable and 0 to reset
  2495. */
  2496.  
  2497. #if HAS_L64XX
  2498.  
  2499. //#define L6470_CHITCHAT // Display additional status info
  2500.  
  2501. #if AXIS_IS_L64XX(X)
  2502. #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) - L6474 max is 16
  2503. #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current
  2504. // L6470 & L6474 - VALID: 375 x (1 - 16) - 6A max - rounds down
  2505. // POWERSTEP01: VALID: 1000 x (1 - 32) - 32A max - rounds down
  2506. #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down)
  2507. // L6470 & L6474 - VALID: 31.25 * (1-128) - 4A max - rounds down
  2508. // POWERSTEP01: VALID: 200 x (1 - 32) - 6.4A max - rounds down
  2509. // L6474 - STALLCURRENT setting is used to set the nominal (TVAL) current
  2510. #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper - not used by L6474
  2511. #define X_CHAIN_POS -1 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI
  2512. #define X_SLEW_RATE 1 // 0-3, Slew 0 is slowest, 3 is fastest
  2513. #endif
  2514.  
  2515. #if AXIS_IS_L64XX(X2)
  2516. #define X2_MICROSTEPS 128
  2517. #define X2_OVERCURRENT 2000
  2518. #define X2_STALLCURRENT 1500
  2519. #define X2_MAX_VOLTAGE 127
  2520. #define X2_CHAIN_POS -1
  2521. #define X2_SLEW_RATE 1
  2522. #endif
  2523.  
  2524. #if AXIS_IS_L64XX(Y)
  2525. #define Y_MICROSTEPS 128
  2526. #define Y_OVERCURRENT 2000
  2527. #define Y_STALLCURRENT 1500
  2528. #define Y_MAX_VOLTAGE 127
  2529. #define Y_CHAIN_POS -1
  2530. #define Y_SLEW_RATE 1
  2531. #endif
  2532.  
  2533. #if AXIS_IS_L64XX(Y2)
  2534. #define Y2_MICROSTEPS 128
  2535. #define Y2_OVERCURRENT 2000
  2536. #define Y2_STALLCURRENT 1500
  2537. #define Y2_MAX_VOLTAGE 127
  2538. #define Y2_CHAIN_POS -1
  2539. #define Y2_SLEW_RATE 1
  2540. #endif
  2541.  
  2542. #if AXIS_IS_L64XX(Z)
  2543. #define Z_MICROSTEPS 128
  2544. #define Z_OVERCURRENT 2000
  2545. #define Z_STALLCURRENT 1500
  2546. #define Z_MAX_VOLTAGE 127
  2547. #define Z_CHAIN_POS -1
  2548. #define Z_SLEW_RATE 1
  2549. #endif
  2550.  
  2551. #if AXIS_IS_L64XX(Z2)
  2552. #define Z2_MICROSTEPS 128
  2553. #define Z2_OVERCURRENT 2000
  2554. #define Z2_STALLCURRENT 1500
  2555. #define Z2_MAX_VOLTAGE 127
  2556. #define Z2_CHAIN_POS -1
  2557. #define Z2_SLEW_RATE 1
  2558. #endif
  2559.  
  2560. #if AXIS_IS_L64XX(Z3)
  2561. #define Z3_MICROSTEPS 128
  2562. #define Z3_OVERCURRENT 2000
  2563. #define Z3_STALLCURRENT 1500
  2564. #define Z3_MAX_VOLTAGE 127
  2565. #define Z3_CHAIN_POS -1
  2566. #define Z3_SLEW_RATE 1
  2567. #endif
  2568.  
  2569. #if AXIS_IS_L64XX(Z4)
  2570. #define Z4_MICROSTEPS 128
  2571. #define Z4_OVERCURRENT 2000
  2572. #define Z4_STALLCURRENT 1500
  2573. #define Z4_MAX_VOLTAGE 127
  2574. #define Z4_CHAIN_POS -1
  2575. #define Z4_SLEW_RATE 1
  2576. #endif
  2577.  
  2578. #if AXIS_IS_L64XX(E0)
  2579. #define E0_MICROSTEPS 128
  2580. #define E0_OVERCURRENT 2000
  2581. #define E0_STALLCURRENT 1500
  2582. #define E0_MAX_VOLTAGE 127
  2583. #define E0_CHAIN_POS -1
  2584. #define E0_SLEW_RATE 1
  2585. #endif
  2586.  
  2587. #if AXIS_IS_L64XX(E1)
  2588. #define E1_MICROSTEPS 128
  2589. #define E1_OVERCURRENT 2000
  2590. #define E1_STALLCURRENT 1500
  2591. #define E1_MAX_VOLTAGE 127
  2592. #define E1_CHAIN_POS -1
  2593. #define E1_SLEW_RATE 1
  2594. #endif
  2595.  
  2596. #if AXIS_IS_L64XX(E2)
  2597. #define E2_MICROSTEPS 128
  2598. #define E2_OVERCURRENT 2000
  2599. #define E2_STALLCURRENT 1500
  2600. #define E2_MAX_VOLTAGE 127
  2601. #define E2_CHAIN_POS -1
  2602. #define E2_SLEW_RATE 1
  2603. #endif
  2604.  
  2605. #if AXIS_IS_L64XX(E3)
  2606. #define E3_MICROSTEPS 128
  2607. #define E3_OVERCURRENT 2000
  2608. #define E3_STALLCURRENT 1500
  2609. #define E3_MAX_VOLTAGE 127
  2610. #define E3_CHAIN_POS -1
  2611. #define E3_SLEW_RATE 1
  2612. #endif
  2613.  
  2614. #if AXIS_IS_L64XX(E4)
  2615. #define E4_MICROSTEPS 128
  2616. #define E4_OVERCURRENT 2000
  2617. #define E4_STALLCURRENT 1500
  2618. #define E4_MAX_VOLTAGE 127
  2619. #define E4_CHAIN_POS -1
  2620. #define E4_SLEW_RATE 1
  2621. #endif
  2622.  
  2623. #if AXIS_IS_L64XX(E5)
  2624. #define E5_MICROSTEPS 128
  2625. #define E5_OVERCURRENT 2000
  2626. #define E5_STALLCURRENT 1500
  2627. #define E5_MAX_VOLTAGE 127
  2628. #define E5_CHAIN_POS -1
  2629. #define E5_SLEW_RATE 1
  2630. #endif
  2631.  
  2632. #if AXIS_IS_L64XX(E6)
  2633. #define E6_MICROSTEPS 128
  2634. #define E6_OVERCURRENT 2000
  2635. #define E6_STALLCURRENT 1500
  2636. #define E6_MAX_VOLTAGE 127
  2637. #define E6_CHAIN_POS -1
  2638. #define E6_SLEW_RATE 1
  2639. #endif
  2640.  
  2641. #if AXIS_IS_L64XX(E7)
  2642. #define E7_MICROSTEPS 128
  2643. #define E7_OVERCURRENT 2000
  2644. #define E7_STALLCURRENT 1500
  2645. #define E7_MAX_VOLTAGE 127
  2646. #define E7_CHAIN_POS -1
  2647. #define E7_SLEW_RATE 1
  2648. #endif
  2649.  
  2650. /**
  2651. * Monitor L6470 drivers for error conditions like over temperature and over current.
  2652. * In the case of over temperature Marlin can decrease the drive until the error condition clears.
  2653. * Other detected conditions can be used to stop the current print.
  2654. * Relevant g-codes:
  2655. * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given.
  2656. * I not present or I0 or I1 - X, Y, Z or E0
  2657. * I2 - X2, Y2, Z2 or E1
  2658. * I3 - Z3 or E3
  2659. * I4 - Z4 or E4
  2660. * I5 - E5
  2661. * M916 - Increase drive level until get thermal warning
  2662. * M917 - Find minimum current thresholds
  2663. * M918 - Increase speed until max or error
  2664. * M122 S0/1 - Report driver parameters
  2665. */
  2666. //#define MONITOR_L6470_DRIVER_STATUS
  2667.  
  2668. #if ENABLED(MONITOR_L6470_DRIVER_STATUS)
  2669. #define KVAL_HOLD_STEP_DOWN 1
  2670. //#define L6470_STOP_ON_ERROR
  2671. #endif
  2672.  
  2673. #endif // HAS_L64XX
  2674.  
  2675. // @section i2cbus
  2676.  
  2677. //
  2678. // I2C Master ID for LPC176x LCD and Digital Current control
  2679. // Does not apply to other peripherals based on the Wire library.
  2680. //
  2681. //#define I2C_MASTER_ID 1 // Set a value from 0 to 2
  2682.  
  2683. /**
  2684. * TWI/I2C BUS
  2685. *
  2686. * This feature is an EXPERIMENTAL feature so it shall not be used on production
  2687. * machines. Enabling this will allow you to send and receive I2C data from slave
  2688. * devices on the bus.
  2689. *
  2690. * ; Example #1
  2691. * ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
  2692. * ; It uses multiple M260 commands with one B<base 10> arg
  2693. * M260 A99 ; Target slave address
  2694. * M260 B77 ; M
  2695. * M260 B97 ; a
  2696. * M260 B114 ; r
  2697. * M260 B108 ; l
  2698. * M260 B105 ; i
  2699. * M260 B110 ; n
  2700. * M260 S1 ; Send the current buffer
  2701. *
  2702. * ; Example #2
  2703. * ; Request 6 bytes from slave device with address 0x63 (99)
  2704. * M261 A99 B5
  2705. *
  2706. * ; Example #3
  2707. * ; Example serial output of a M261 request
  2708. * echo:i2c-reply: from:99 bytes:5 data:hello
  2709. */
  2710.  
  2711. //#define EXPERIMENTAL_I2CBUS
  2712. #if ENABLED(EXPERIMENTAL_I2CBUS)
  2713. #define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
  2714. #endif
  2715.  
  2716. // @section extras
  2717.  
  2718. /**
  2719. * Photo G-code
  2720. * Add the M240 G-code to take a photo.
  2721. * The photo can be triggered by a digital pin or a physical movement.
  2722. */
  2723. //#define PHOTO_GCODE
  2724. #if ENABLED(PHOTO_GCODE)
  2725. // A position to move to (and raise Z) before taking the photo
  2726. //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z)
  2727. //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P)
  2728. //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S)
  2729.  
  2730. // Canon RC-1 or homebrew digital camera trigger
  2731. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  2732. //#define PHOTOGRAPH_PIN 23
  2733.  
  2734. // Canon Hack Development Kit
  2735. // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
  2736. //#define CHDK_PIN 4
  2737.  
  2738. // Optional second move with delay to trigger the camera shutter
  2739. //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J)
  2740.  
  2741. // Duration to hold the switch or keep CHDK_PIN high
  2742. //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D)
  2743.  
  2744. /**
  2745. * PHOTO_PULSES_US may need adjustment depending on board and camera model.
  2746. * Pin must be running at 48.4kHz.
  2747. * Be sure to use a PHOTOGRAPH_PIN which can rise and fall quick enough.
  2748. * (e.g., MKS SBase temp sensor pin was too slow, so used P1.23 on J8.)
  2749. *
  2750. * Example pulse data for Nikon: https://bit.ly/2FKD0Aq
  2751. * IR Wiring: https://git.io/JvJf7
  2752. */
  2753. //#define PHOTO_PULSES_US { 2000, 27850, 400, 1580, 400, 3580, 400 } // (µs) Durations for each 48.4kHz oscillation
  2754. #ifdef PHOTO_PULSES_US
  2755. #define PHOTO_PULSE_DELAY_US 13 // (µs) Approximate duration of each HIGH and LOW pulse in the oscillation
  2756. #endif
  2757. #endif
  2758.  
  2759. /**
  2760. * Spindle & Laser control
  2761. *
  2762. * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
  2763. * to set spindle speed, spindle direction, and laser power.
  2764. *
  2765. * SuperPid is a router/spindle speed controller used in the CNC milling community.
  2766. * Marlin can be used to turn the spindle on and off. It can also be used to set
  2767. * the spindle speed from 5,000 to 30,000 RPM.
  2768. *
  2769. * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
  2770. * hardware PWM pin for the speed control and a pin for the rotation direction.
  2771. *
  2772. * See https://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
  2773. */
  2774. //#define SPINDLE_FEATURE
  2775. //#define LASER_FEATURE
  2776. #if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
  2777. #define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
  2778. #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
  2779. #define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
  2780.  
  2781. #define SPINDLE_LASER_FREQUENCY 2500 // (Hz) Spindle/laser frequency (only on supported HALs: AVR and LPC)
  2782.  
  2783. /**
  2784. * Speed / Power can be set ('M3 S') and displayed in terms of:
  2785. * - PWM255 (S0 - S255)
  2786. * - PERCENT (S0 - S100)
  2787. * - RPM (S0 - S50000) Best for use with a spindle
  2788. */
  2789. #define CUTTER_POWER_DISPLAY PWM255
  2790.  
  2791. /**
  2792. * Relative mode uses relative range (SPEED_POWER_MIN to SPEED_POWER_MAX) instead of normal range (0 to SPEED_POWER_MAX)
  2793. * Best use with SuperPID router controller where for example S0 = 5,000 RPM and S255 = 30,000 RPM
  2794. */
  2795. //#define CUTTER_POWER_RELATIVE // Set speed proportional to [SPEED_POWER_MIN...SPEED_POWER_MAX] instead of directly
  2796.  
  2797. #if ENABLED(SPINDLE_FEATURE)
  2798. //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
  2799. #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
  2800. #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
  2801.  
  2802. #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
  2803. #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
  2804.  
  2805. /**
  2806. * M3/M4 uses the following equation to convert speed/power to PWM duty cycle
  2807. * Power = ((DC / 255 * 100) - SPEED_POWER_INTERCEPT)) * (1 / SPEED_POWER_SLOPE)
  2808. * where PWM DC varies from 0 to 255
  2809. *
  2810. * Set these required parameters for your controller
  2811. */
  2812. #define SPEED_POWER_SLOPE 118.4 // SPEED_POWER_SLOPE = SPEED_POWER_MAX / 255
  2813. #define SPEED_POWER_INTERCEPT 0
  2814. #define SPEED_POWER_MIN 5000
  2815. #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
  2816. #define SPEED_POWER_STARTUP 25000 // The default value for speed power when M3 is called without arguments
  2817.  
  2818. #else
  2819.  
  2820. #define SPEED_POWER_SLOPE 0.3922 // SPEED_POWER_SLOPE = SPEED_POWER_MAX / 255
  2821. #define SPEED_POWER_INTERCEPT 0
  2822. #define SPEED_POWER_MIN 0
  2823. #define SPEED_POWER_MAX 100 // 0-100%
  2824. #define SPEED_POWER_STARTUP 80 // The default value for speed power when M3 is called without arguments
  2825.  
  2826. /**
  2827. * Enable inline laser power to be handled in the planner / stepper routines.
  2828. * Inline power is specified by the I (inline) flag in an M3 command (e.g., M3 S20 I)
  2829. * or by the 'S' parameter in G0/G1/G2/G3 moves (see LASER_MOVE_POWER).
  2830. *
  2831. * This allows the laser to keep in perfect sync with the planner and removes
  2832. * the powerup/down delay since lasers require negligible time.
  2833. */
  2834. #define LASER_POWER_INLINE
  2835.  
  2836. #if ENABLED(LASER_POWER_INLINE)
  2837. /**
  2838. * Scale the laser's power in proportion to the movement rate.
  2839. *
  2840. * - Sets the entry power proportional to the entry speed over the nominal speed.
  2841. * - Ramps the power up every N steps to approximate the speed trapezoid.
  2842. * - Due to the limited power resolution this is only approximate.
  2843. */
  2844. #define LASER_POWER_INLINE_TRAPEZOID
  2845.  
  2846. /**
  2847. * Continuously calculate the current power (nominal_power * current_rate / nominal_rate).
  2848. * Required for accurate power with non-trapezoidal acceleration (e.g., S_CURVE_ACCELERATION).
  2849. * This is a costly calculation so this option is discouraged on 8-bit AVR boards.
  2850. *
  2851. * LASER_POWER_INLINE_TRAPEZOID_CONT_PER defines how many step cycles there are between power updates. If your
  2852. * board isn't able to generate steps fast enough (and you are using LASER_POWER_INLINE_TRAPEZOID_CONT), increase this.
  2853. * Note that when this is zero it means it occurs every cycle; 1 means a delay wait one cycle then run, etc.
  2854. */
  2855. //#define LASER_POWER_INLINE_TRAPEZOID_CONT
  2856.  
  2857. /**
  2858. * Stepper iterations between power updates. Increase this value if the board
  2859. * can't keep up with the processing demands of LASER_POWER_INLINE_TRAPEZOID_CONT.
  2860. * Disable (or set to 0) to recalculate power on every stepper iteration.
  2861. */
  2862. //#define LASER_POWER_INLINE_TRAPEZOID_CONT_PER 10
  2863.  
  2864. /**
  2865. * Include laser power in G0/G1/G2/G3/G5 commands with the 'S' parameter
  2866. */
  2867. //#define LASER_MOVE_POWER
  2868.  
  2869. #if ENABLED(LASER_MOVE_POWER)
  2870. // Turn off the laser on G0 moves with no power parameter.
  2871. // If a power parameter is provided, use that instead.
  2872. //#define LASER_MOVE_G0_OFF
  2873. #endif
  2874.  
  2875. /**
  2876. * Inline flag inverted
  2877. *
  2878. * WARNING: M5 will NOT turn off the laser unless another move
  2879. * is done (so G-code files must end with 'M5 I').
  2880. */
  2881. //#define LASER_POWER_INLINE_INVERT
  2882.  
  2883. /**
  2884. * Continuously apply inline power. ('M3 S3' == 'G1 S3' == 'M3 S3 I')
  2885. *
  2886. * The laser might do some weird things, so only enable this
  2887. * feature if you understand the implications.
  2888. */
  2889. //#define LASER_POWER_INLINE_CONTINUOUS
  2890.  
  2891. #else
  2892.  
  2893. #define SPINDLE_LASER_POWERUP_DELAY 50 // (ms) Delay to allow the spindle/laser to come up to speed/power
  2894. #define SPINDLE_LASER_POWERDOWN_DELAY 50 // (ms) Delay to allow the spindle to stop
  2895.  
  2896. #endif
  2897. #endif
  2898. #endif
  2899.  
  2900. /**
  2901. * Coolant Control
  2902. *
  2903. * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off.
  2904. *
  2905. * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined.
  2906. */
  2907. //#define COOLANT_CONTROL
  2908. #if ENABLED(COOLANT_CONTROL)
  2909. #define COOLANT_MIST // Enable if mist coolant is present
  2910. #define COOLANT_FLOOD // Enable if flood coolant is present
  2911. #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed
  2912. #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed
  2913. #endif
  2914.  
  2915. /**
  2916. * Filament Width Sensor
  2917. *
  2918. * Measures the filament width in real-time and adjusts
  2919. * flow rate to compensate for any irregularities.
  2920. *
  2921. * Also allows the measured filament diameter to set the
  2922. * extrusion rate, so the slicer only has to specify the
  2923. * volume.
  2924. *
  2925. * Only a single extruder is supported at this time.
  2926. *
  2927. * 34 RAMPS_14 : Analog input 5 on the AUX2 connector
  2928. * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
  2929. * 301 RAMBO : Analog input 3
  2930. *
  2931. * Note: May require analog pins to be defined for other boards.
  2932. */
  2933. //#define FILAMENT_WIDTH_SENSOR
  2934.  
  2935. #if ENABLED(FILAMENT_WIDTH_SENSOR)
  2936. #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4]
  2937. #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
  2938.  
  2939. #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it
  2940. #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
  2941.  
  2942. #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
  2943.  
  2944. // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
  2945. //#define FILAMENT_LCD_DISPLAY
  2946. #endif
  2947.  
  2948. /**
  2949. * CNC Coordinate Systems
  2950. *
  2951. * Enables G53 and G54-G59.3 commands to select coordinate systems
  2952. * and G92.1 to reset the workspace to native machine space.
  2953. */
  2954. //#define CNC_COORDINATE_SYSTEMS
  2955.  
  2956. /**
  2957. * Auto-report temperatures with M155 S<seconds>
  2958. */
  2959. #define AUTO_REPORT_TEMPERATURES
  2960.  
  2961. /**
  2962. * Include capabilities in M115 output
  2963. */
  2964. #define EXTENDED_CAPABILITIES_REPORT
  2965. #if ENABLED(EXTENDED_CAPABILITIES_REPORT)
  2966. //#define M115_GEOMETRY_REPORT
  2967. #endif
  2968.  
  2969. /**
  2970. * Expected Printer Check
  2971. * Add the M16 G-code to compare a string to the MACHINE_NAME.
  2972. * M16 with a non-matching string causes the printer to halt.
  2973. */
  2974. //#define EXPECTED_PRINTER_CHECK
  2975.  
  2976. /**
  2977. * Disable all Volumetric extrusion options
  2978. */
  2979. //#define NO_VOLUMETRICS
  2980.  
  2981. #if DISABLED(NO_VOLUMETRICS)
  2982. /**
  2983. * Volumetric extrusion default state
  2984. * Activate to make volumetric extrusion the default method,
  2985. * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter.
  2986. *
  2987. * M200 D0 to disable, M200 Dn to set a new diameter.
  2988. */
  2989. //#define VOLUMETRIC_DEFAULT_ON
  2990. #endif
  2991.  
  2992. /**
  2993. * Enable this option for a leaner build of Marlin that removes all
  2994. * workspace offsets, simplifying coordinate transformations, leveling, etc.
  2995. *
  2996. * - M206 and M428 are disabled.
  2997. * - G92 will revert to its behavior from Marlin 1.0.
  2998. */
  2999. //#define NO_WORKSPACE_OFFSETS
  3000.  
  3001. // Extra options for the M114 "Current Position" report
  3002. //#define M114_DETAIL // Use 'M114` for details to check planner calculations
  3003. //#define M114_REALTIME // Real current position based on forward kinematics
  3004. //#define M114_LEGACY // M114 used to synchronize on every call. Enable if needed.
  3005.  
  3006. /**
  3007. * Set the number of proportional font spaces required to fill up a typical character space.
  3008. * This can help to better align the output of commands like `G29 O` Mesh Output.
  3009. *
  3010. * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0.
  3011. * Otherwise, adjust according to your client and font.
  3012. */
  3013. #define PROPORTIONAL_FONT_RATIO 1.0
  3014.  
  3015. /**
  3016. * Spend 28 bytes of SRAM to optimize the GCode parser
  3017. */
  3018. #define FASTER_GCODE_PARSER
  3019.  
  3020. #if ENABLED(FASTER_GCODE_PARSER)
  3021. //#define GCODE_QUOTED_STRINGS // Support for quoted string parameters
  3022. #endif
  3023.  
  3024. //#define GCODE_CASE_INSENSITIVE // Accept G-code sent to the firmware in lowercase
  3025.  
  3026. //#define REPETIER_GCODE_M360 // Add commands originally from Repetier FW
  3027.  
  3028. /**
  3029. * CNC G-code options
  3030. * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc.
  3031. * Note that G0 feedrates should be used with care for 3D printing (if used at all).
  3032. * High feedrates may cause ringing and harm print quality.
  3033. */
  3034. //#define PAREN_COMMENTS // Support for parentheses-delimited comments
  3035. //#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc.
  3036.  
  3037. // Enable and set a (default) feedrate for all G0 moves
  3038. //#define G0_FEEDRATE 3000 // (mm/m)
  3039. #ifdef G0_FEEDRATE
  3040. //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
  3041. #endif
  3042.  
  3043. /**
  3044. * Startup commands
  3045. *
  3046. * Execute certain G-code commands immediately after power-on.
  3047. */
  3048. //#define STARTUP_COMMANDS "M17 Z"
  3049.  
  3050. /**
  3051. * G-code Macros
  3052. *
  3053. * Add G-codes M810-M819 to define and run G-code macros.
  3054. * Macros are not saved to EEPROM.
  3055. */
  3056. //#define GCODE_MACROS
  3057. #if ENABLED(GCODE_MACROS)
  3058. #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used
  3059. #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro
  3060. #endif
  3061.  
  3062. /**
  3063. * User-defined menu items that execute custom GCode
  3064. */
  3065. //#define CUSTOM_USER_MENUS
  3066. #if ENABLED(CUSTOM_USER_MENUS)
  3067. //#define CUSTOM_USER_MENU_TITLE "Custom Commands"
  3068. #define USER_SCRIPT_DONE "M117 User Script Done"
  3069. #define USER_SCRIPT_AUDIBLE_FEEDBACK
  3070. //#define USER_SCRIPT_RETURN // Return to status screen after a script
  3071.  
  3072. #define USER_DESC_1 "Home & UBL Info"
  3073. #define USER_GCODE_1 "G28\nG29 W"
  3074.  
  3075. #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL
  3076. #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
  3077.  
  3078. #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL
  3079. #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
  3080.  
  3081. #define USER_DESC_4 "Heat Bed/Home/Level"
  3082. #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
  3083.  
  3084. #define USER_DESC_5 "Home & Info"
  3085. #define USER_GCODE_5 "G28\nM503"
  3086. #endif
  3087.  
  3088. /**
  3089. * Host Action Commands
  3090. *
  3091. * Define host streamer action commands in compliance with the standard.
  3092. *
  3093. * See https://reprap.org/wiki/G-code#Action_commands
  3094. * Common commands ........ poweroff, pause, paused, resume, resumed, cancel
  3095. * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed
  3096. *
  3097. * Some features add reason codes to extend these commands.
  3098. *
  3099. * Host Prompt Support enables Marlin to use the host for user prompts so
  3100. * filament runout and other processes can be managed from the host side.
  3101. */
  3102. //#define HOST_ACTION_COMMANDS
  3103. #if ENABLED(HOST_ACTION_COMMANDS)
  3104. //#define HOST_PROMPT_SUPPORT
  3105. #endif
  3106.  
  3107. /**
  3108. * Cancel Objects
  3109. *
  3110. * Implement M486 to allow Marlin to skip objects
  3111. */
  3112. //#define CANCEL_OBJECTS
  3113.  
  3114. /**
  3115. * I2C position encoders for closed loop control.
  3116. * Developed by Chris Barr at Aus3D.
  3117. *
  3118. * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder
  3119. * Github: https://github.com/Aus3D/MagneticEncoder
  3120. *
  3121. * Supplier: http://aus3d.com.au/magnetic-encoder-module
  3122. * Alternative Supplier: http://reliabuild3d.com/
  3123. *
  3124. * Reliabuild encoders have been modified to improve reliability.
  3125. */
  3126.  
  3127. //#define I2C_POSITION_ENCODERS
  3128. #if ENABLED(I2C_POSITION_ENCODERS)
  3129.  
  3130. #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5
  3131. // encoders supported currently.
  3132.  
  3133. #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200.
  3134. #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. <X|Y|Z|E>_AXIS.
  3135. #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or-
  3136. // I2CPE_ENC_TYPE_ROTARY.
  3137. #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for
  3138. // 1mm poles. For linear encoders this is ticks / mm,
  3139. // for rotary encoders this is ticks / revolution.
  3140. //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper
  3141. // steps per full revolution (motor steps/rev * microstepping)
  3142. //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel.
  3143. #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction.
  3144. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the
  3145. // printer will attempt to correct the error; errors
  3146. // smaller than this are ignored to minimize effects of
  3147. // measurement noise / latency (filter).
  3148.  
  3149. #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2.
  3150. #define I2CPE_ENC_2_AXIS Y_AXIS
  3151. #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR
  3152. #define I2CPE_ENC_2_TICKS_UNIT 2048
  3153. //#define I2CPE_ENC_2_TICKS_REV (16 * 200)
  3154. //#define I2CPE_ENC_2_INVERT
  3155. #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP
  3156. #define I2CPE_ENC_2_EC_THRESH 0.10
  3157.  
  3158. #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options
  3159. #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below.
  3160.  
  3161. #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4.
  3162. #define I2CPE_ENC_4_AXIS E_AXIS
  3163.  
  3164. #define I2CPE_ENC_5_ADDR 34 // Encoder 5.
  3165. #define I2CPE_ENC_5_AXIS E_AXIS
  3166.  
  3167. // Default settings for encoders which are enabled, but without settings configured above.
  3168. #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR
  3169. #define I2CPE_DEF_ENC_TICKS_UNIT 2048
  3170. #define I2CPE_DEF_TICKS_REV (16 * 200)
  3171. #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE
  3172. #define I2CPE_DEF_EC_THRESH 0.1
  3173.  
  3174. //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
  3175. // axis after which the printer will abort. Comment out to
  3176. // disable abort behavior.
  3177.  
  3178. #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
  3179. // for this amount of time (in ms) before the encoder
  3180. // is trusted again.
  3181.  
  3182. /**
  3183. * Position is checked every time a new command is executed from the buffer but during long moves,
  3184. * this setting determines the minimum update time between checks. A value of 100 works well with
  3185. * error rolling average when attempting to correct only for skips and not for vibration.
  3186. */
  3187. #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks.
  3188.  
  3189. // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
  3190. #define I2CPE_ERR_ROLLING_AVERAGE
  3191.  
  3192. #endif // I2C_POSITION_ENCODERS
  3193.  
  3194. /**
  3195. * Analog Joystick(s)
  3196. */
  3197. //#define JOYSTICK
  3198. #if ENABLED(JOYSTICK)
  3199. #define JOY_X_PIN 5 // RAMPS: Suggested pin A5 on AUX2
  3200. #define JOY_Y_PIN 10 // RAMPS: Suggested pin A10 on AUX2
  3201. #define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2
  3202. #define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2
  3203.  
  3204. //#define INVERT_JOY_X // Enable if X direction is reversed
  3205. //#define INVERT_JOY_Y // Enable if Y direction is reversed
  3206. //#define INVERT_JOY_Z // Enable if Z direction is reversed
  3207.  
  3208. // Use M119 with JOYSTICK_DEBUG to find reasonable values after connecting:
  3209. #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
  3210. #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
  3211. #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
  3212. #endif
  3213.  
  3214. /**
  3215. * MAX7219 Debug Matrix
  3216. *
  3217. * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display.
  3218. * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage.
  3219. */
  3220. //#define MAX7219_DEBUG
  3221. #if ENABLED(MAX7219_DEBUG)
  3222. #define MAX7219_CLK_PIN 64
  3223. #define MAX7219_DIN_PIN 57
  3224. #define MAX7219_LOAD_PIN 44
  3225.  
  3226. //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix
  3227. #define MAX7219_INIT_TEST 2 // Test pattern at startup: 0=none, 1=sweep, 2=spiral
  3228. #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain.
  3229. #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°)
  3230. // connector at: right=0 bottom=-90 top=90 left=180
  3231. //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order
  3232. //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side
  3233.  
  3234. /**
  3235. * Sample debug features
  3236. * If you add more debug displays, be careful to avoid conflicts!
  3237. */
  3238. #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning
  3239. #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row
  3240. #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row
  3241.  
  3242. #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row
  3243. // If you experience stuttering, reboots, etc. this option can reveal how
  3244. // tweaks made to the configuration are affecting the printer in real-time.
  3245. #endif
  3246.  
  3247. /**
  3248. * NanoDLP Sync support
  3249. *
  3250. * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp"
  3251. * string to enable synchronization with DLP projector exposure. This change will allow to use
  3252. * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands
  3253. */
  3254. //#define NANODLP_Z_SYNC
  3255. #if ENABLED(NANODLP_Z_SYNC)
  3256. //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move.
  3257. // Default behavior is limited to Z axis only.
  3258. #endif
  3259.  
  3260. /**
  3261. * WiFi Support (Espressif ESP32 WiFi)
  3262. */
  3263. //#define WIFISUPPORT // Marlin embedded WiFi managenent
  3264. //#define ESP3D_WIFISUPPORT // ESP3D Library WiFi management (https://github.com/luc-github/ESP3DLib)
  3265.  
  3266. #if EITHER(WIFISUPPORT, ESP3D_WIFISUPPORT)
  3267. //#define WEBSUPPORT // Start a webserver (which may include auto-discovery)
  3268. //#define OTASUPPORT // Support over-the-air firmware updates
  3269. //#define WIFI_CUSTOM_COMMAND // Accept feature config commands (e.g., WiFi ESP3D) from the host
  3270.  
  3271. /**
  3272. * To set a default WiFi SSID / Password, create a file called Configuration_Secure.h with
  3273. * the following defines, customized for your network. This specific file is excluded via
  3274. * .gitignore to prevent it from accidentally leaking to the public.
  3275. *
  3276. * #define WIFI_SSID "WiFi SSID"
  3277. * #define WIFI_PWD "WiFi Password"
  3278. */
  3279. //#include "Configuration_Secure.h" // External file with WiFi SSID / Password
  3280. #endif
  3281.  
  3282. /**
  3283. * Prusa Multi-Material Unit v2
  3284. * Enable in Configuration.h
  3285. */
  3286. #if ENABLED(PRUSA_MMU2)
  3287.  
  3288. // Serial port used for communication with MMU2.
  3289. // For AVR enable the UART port used for the MMU. (e.g., internalSerial)
  3290. // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2)
  3291. #define INTERNAL_SERIAL_PORT 2
  3292. #define MMU2_SERIAL internalSerial
  3293.  
  3294. // Use hardware reset for MMU if a pin is defined for it
  3295. //#define MMU2_RST_PIN 23
  3296.  
  3297. // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up)
  3298. //#define MMU2_MODE_12V
  3299.  
  3300. // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout
  3301. #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600"
  3302.  
  3303. // Add an LCD menu for MMU2
  3304. //#define MMU2_MENUS
  3305. #if ENABLED(MMU2_MENUS)
  3306. // Settings for filament load / unload from the LCD menu.
  3307. // This is for Prusa MK3-style extruders. Customize for your hardware.
  3308. #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0
  3309. #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \
  3310. { 7.2, 1145 }, \
  3311. { 14.4, 871 }, \
  3312. { 36.0, 1393 }, \
  3313. { 14.4, 871 }, \
  3314. { 50.0, 198 }
  3315.  
  3316. #define MMU2_RAMMING_SEQUENCE \
  3317. { 1.0, 1000 }, \
  3318. { 1.0, 1500 }, \
  3319. { 2.0, 2000 }, \
  3320. { 1.5, 3000 }, \
  3321. { 2.5, 4000 }, \
  3322. { -15.0, 5000 }, \
  3323. { -14.0, 1200 }, \
  3324. { -6.0, 600 }, \
  3325. { 10.0, 700 }, \
  3326. { -10.0, 400 }, \
  3327. { -50.0, 2000 }
  3328. #endif
  3329.  
  3330. /**
  3331. * MMU Extruder Sensor
  3332. * Add support for Prusa IR Sensor (or other) to detect that filament reach the extruder to make loading filament more reliable
  3333. * If your extruder is equipped with a filament sensor located less than 38mm from the gears you can use this feature
  3334. * During loading to the extruder, the sensor will stop the loading command when he's triggered and make a last move to load filament to the gears
  3335. * If no filament is detected, MMU2 will make more loading attemps, if finally no filament is detected, the printer will enter in runout state
  3336. */
  3337.  
  3338. //#define MMU_EXTRUDER_SENSOR
  3339. #if ENABLED(MMU_EXTRUDER_SENSOR)
  3340. #define MMU_LOADING_ATTEMPTS_NR 5 //max. number of attempts to load filament if first load fail
  3341. #endif
  3342.  
  3343. /**
  3344. * Using a sensor like the MMU2S
  3345. * This mode only work if you have a MK3S extruder with sensor sensing the extruder idler mmu2s
  3346. * See https://help.prusa3d.com/en/guide/3b-mk3s-mk2-5s-extruder-upgrade_41560, step 11
  3347. */
  3348.  
  3349. //#define PRUSA_MMU2_S_MODE
  3350. #if ENABLED(PRUSA_MMU2_S_MODE)
  3351. #define MMU2_C0_RETRY 5 // Number of retries (total time = timeout*retries)
  3352.  
  3353. #define MMU2_CAN_LOAD_FEEDRATE 800 // (mm/m)
  3354. #define MMU2_CAN_LOAD_SEQUENCE \
  3355. { 0.1, MMU2_CAN_LOAD_FEEDRATE }, \
  3356. { 60.0, MMU2_CAN_LOAD_FEEDRATE }, \
  3357. { -52.0, MMU2_CAN_LOAD_FEEDRATE }
  3358.  
  3359. #define MMU2_CAN_LOAD_RETRACT 6.0 // (mm) Keep under the distance between Load Sequence values
  3360. #define MMU2_CAN_LOAD_DEVIATION 0.8 // (mm) Acceptable deviation
  3361.  
  3362. #define MMU2_CAN_LOAD_INCREMENT 0.2 // (mm) To reuse within MMU2 module
  3363. #define MMU2_CAN_LOAD_INCREMENT_SEQUENCE \
  3364. { -MMU2_CAN_LOAD_INCREMENT, MMU2_CAN_LOAD_FEEDRATE }
  3365.  
  3366. #endif
  3367.  
  3368. //#define MMU2_DEBUG // Write debug info to serial output
  3369.  
  3370. #endif // PRUSA_MMU2
  3371.  
  3372. /**
  3373. * Advanced Print Counter settings
  3374. */
  3375. #if ENABLED(PRINTCOUNTER)
  3376. #define SERVICE_WARNING_BUZZES 3
  3377. // Activate up to 3 service interval watchdogs
  3378. //#define SERVICE_NAME_1 "Service S"
  3379. //#define SERVICE_INTERVAL_1 100 // print hours
  3380. //#define SERVICE_NAME_2 "Service L"
  3381. //#define SERVICE_INTERVAL_2 200 // print hours
  3382. //#define SERVICE_NAME_3 "Service 3"
  3383. //#define SERVICE_INTERVAL_3 1 // print hours
  3384. #endif
  3385.  
  3386. // @section develop
  3387.  
  3388. //
  3389. // M100 Free Memory Watcher to debug memory usage
  3390. //
  3391. //#define M100_FREE_MEMORY_WATCHER
  3392.  
  3393. //
  3394. // M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe
  3395. //
  3396. //#define PINS_DEBUGGING
  3397.  
  3398. // Enable Marlin dev mode which adds some special commands
  3399. //#define MARLIN_DEV_MODE
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!