G2A Many GEOs
SHARE
TWEET

serial console log

a guest May 17th, 2017 56 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1.          __  __                      _ _
  2.         |  \/  | __ _ _ ____   _____| | |
  3.         | |\/| |/ _` | '__\ \ / / _ \ | |
  4.         | |  | | (_| | |   \ V /  __/ | |
  5.         |_|  |_|\__,_|_|    \_/ \___|_|_|
  6.  _   _     ____              _
  7. | | | |   | __ )  ___   ___ | |_
  8. | | | |___|  _ \ / _ \ / _ \| __|
  9. | |_| |___| |_) | (_) | (_) | |_
  10.  \___/    |____/ \___/ \___/ \__|
  11.  ** MARVELL BOARD: DB-88F6282A-BP LE
  12.  
  13. U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9
  14.  
  15. U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00
  16.  
  17. Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
  18. SysClock = 533Mhz , TClock = 200Mhz
  19.  
  20. DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8
  21. DRAM CS[0] base 0x00000000   size 512MB
  22. DRAM Total size 512MB  16bit width
  23. Addresses 10M - 0M are saved for the U-Boot usage.
  24. Mem malloc Initialization (10M - 7M): Done
  25. NAND:128 MB
  26. Flash:  0 kB
  27.  
  28. CPU : Marvell Feroceon (Rev 1)
  29. Kernel address is 0x4640000.
  30.  
  31. Streaming disabled
  32. Write allocate disabled
  33.  
  34.  
  35. USB 0: host mode
  36.         [BlueDBG] reseting SoC Pex[0]  0 ...
  37. PEX 0: PCI Express Root Complex Interface
  38. PEX interface detected Link X1
  39.         [BlueDBG] reseting SoC Pex[1]  0 ...
  40.         [BlueDBG] reseting SoC Pex[1]  1 ...
  41.         [BlueDBG] reseting SoC Pex[1]  2 ...
  42.         [BlueDBG] reseting SoC Pex[1]  3 ...
  43.         [BlueDBG] reseting SoC Pex[1]  4 ...
  44.         [BlueDBG] reseting SoC Pex[1]  5 ...
  45.         [BlueDBG] reseting SoC Pex[1]  6 ...
  46.         [BlueDBG] reseting SoC Pex[1]  7 ...
  47.         [BlueDBG] reseting SoC Pex[1]  8 ...
  48.         [BlueDBG] reseting SoC Pex[1]  9 ...
  49.         [BlueDBG] reseting SoC Pex[1]  10 ...
  50. PEX 1: interface detected no Link.
  51. Net:   egiga0 [PRIME]
  52. Hit any key to stop autoboot:  0
  53. Marvell>> printenv
  54. bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
  55. bootdelay=2
  56. baudrate=115200
  57. loads_echo=0
  58. ipaddr=10.4.52.165
  59. serverip=10.4.52.7
  60. rootpath=/srv/ubuntu
  61. netmask=255.255.255.0
  62. nandEcc=1bit
  63. MODEL_ID=AE03
  64. PRODUCT_NAME=NSA-325v2
  65. FEATURE_BIT=00
  66. CONTRY_TYPE=FF
  67. VENDOR_NAME=MitraStar Technology Corp.
  68. run_diag=yes
  69. arcNumber=4495
  70. bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
  71. bootargs_linux=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8
  72. bootcmd_linux=setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /uImage; ext2load usb 0:1 0x01100000 /uInitrd; bootm $(loadaddr) 0x01100000
  73. bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr)
  74. to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset
  75. to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset
  76. console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
  77. ethprime=egiga0
  78. bootargs_root=root=/dev/nfs rw
  79. bootargs_end=:::orion:eth0:none
  80. image_name=uImage
  81. standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
  82. lcd0_enable=0
  83. lcd0_params=640x480-16@60
  84. ethaddr=00:50:43:00:02:02
  85. ethmtu=1500
  86. mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
  87. mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
  88. usb0Mode=host
  89. yuk_ethaddr=00:00:00:EE:51:81
  90. netretry=no
  91. rcvrip=169.254.100.100
  92. loadaddr=0x02000000
  93. autoload=no
  94. image_multi=yes
  95. ethact=egiga0
  96. bootcmd='run bootcmd_linux'
  97. stdin=serial
  98. stdout=serial
  99. stderr=serial
  100. mainlineLinux=yes
  101. enaMonExt=no
  102. enaCpuStream=no
  103. enaWrAllo=no
  104. pexMode=RC
  105. disL2Cache=no
  106. setL2CacheWT=yes
  107. disL2Prefetch=yes
  108. enaICPref=yes
  109. enaDCPref=yes
  110. sata_dma_mode=yes
  111. netbsd_en=no
  112. vxworks_en=no
  113. disaMvPnp=no
  114. enaAutoRecovery=yes
  115. kernel_addr=0x4640000
  116. pcieTune=no
  117. pcieTune1=no
  118.  
  119. Environment size: 2494/131068 bytes
  120. Marvell>> boot
  121. (Re)start USB...
  122. USB:   scanning bus for devices... 2 USB Device(s) found
  123. Waiting for storage device(s) to settle before scanning...
  124. 0 Storage Device(s) found
  125. ** Bad partition 1 **
  126. ** Bad partition 1 **
  127. ## Booting image at 02000000 ...
  128. Bad Magic Number
  129. Marvell>>
RAW Paste Data
Ledger Nano X - The secure hardware wallet
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
Top