Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- AMLOGIC:~ # dmesg
- [ 0.000000@0] Booting Linux on physical CPU 0x200
- [ 0.000000@0] Linux version 3.10.84 (alex@amlinux.ru) (gcc version 4.9.3 (GCC) ) #1 SMP PREEMPT Mon Aug 3 14:59:31 MSK 2015
- [ 0.000000@0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
- [ 0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000@0] Machine: Amlogic Meson8, model: AMLOGIC
- [ 0.000000@0] physical memory start address is 0x200000
- [ 0.000000@0] reserved_end is 1f2fffff
- [ 0.000000@0]
- [ 0.000000@0] Total memory is 2046 MiB
- [ 0.000000@0] Reserved low memory from 0x06000000 to 0x1f2fffff, size: 403 MiB
- [ 0.000000@0] mesonfb0(low) : 0x06100000 - 0x0a900000 ( 72 MiB)
- [ 0.000000@0] mesonfb1(low) : 0x0a900000 - 0x0aa00000 ( 1 MiB)
- [ 0.000000@0] deinterlace0(high) : 0x7e800000 - 0x80000000 ( 24 MiB)
- [ 0.000000@0] mesonstream0(low) : 0x0aa00000 - 0x0ca00000 ( 32 MiB)
- [ 0.000000@0] vdec0(low) : 0x0ca00000 - 0x1ca00000 (256 MiB)
- [ 0.000000@0] ppmgr0(high) : 0x7d800000 - 0x7e800000 ( 16 MiB)
- [ 0.000000@0] vdin00(low) : 0x1ca00000 - 0x1cb00000 ( 1 MiB)
- [ 0.000000@0] vdin10(low) : 0x1cb00000 - 0x1db00000 ( 16 MiB)
- [ 0.000000@0] amlvideo20(low) : 0x1db00000 - 0x1f300000 ( 24 MiB)
- [ 0.000000@0] get storage device: storage 2
- [ 0.000000@0] value=2
- [ 0.000000@0] get_storage_device : get storage device: storage 2
- [ 0.000000@0] get_storage_device : value=2
- [ 0.000000@0] [get_storage_device] storage_flag=2
- [ 0.000000@0] cma: CMA: reserved 8 MiB at 2f000000
- [ 0.000000@0] cma: Found region@0, memory base 0, size 18 MiB
- [ 0.000000@0] cma: CMA: reserved 20 MiB at 2dc00000
- [ 0.000000@0] Memory policy: ECC disabled, Data cache writealloc
- [ 0.000000@0] On node 0 totalpages: 406784
- [ 0.000000@0] free_area_init_node: node 0, pgdat c0c48cc0, node_mem_map c0ec6000
- [ 0.000000@0] Normal zone: 1520 pages used for memmap
- [ 0.000000@0] Normal zone: 0 pages reserved
- [ 0.000000@0] Normal zone: 87808 pages, LIFO batch:15
- [ 0.000000@0] HighMem zone: 2492 pages used for memmap
- [ 0.000000@0] HighMem zone: 318976 pages, LIFO batch:31
- [ 0.000000@0] Meson chip version = RevA (1D:A - 0:74E)
- [ 0.000000@0] PERCPU: Embedded 8 pages/cpu @c1e85000 s12288 r8192 d12288 u32768
- [ 0.000000@0] pcpu-alloc: s12288 r8192 d12288 u32768 alloc=8*4096
- [ 0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
- [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 405264
- [ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200n8 no_console_suspend storage=2 cvbsdrv=0 vdaccfg=0xa000 logo=osd1,loaded,0x15100000,1080p,full hdmimode=1080p cvbsmode=576cvbs androidboot.firstboot=0 hdmitx=cecf hdmitx=cecf boot=/dev/mmcblk0p1 disk=/dev/mmcblk0p2 BOOT_IMAGE=kernel.img scaling_governor=ondemand scaling_min_freq=96000 scaling_max_freq=1608000 ssh
- [ 0.000000@0] cvbs performance line = 0
- [ 0.000000@0] cvbs trimming line = 0xa000
- [ 0.000000@0] cvbs trimming.1.v5: 0xa0, 0x0
- [ 0.000000@0] osd1:1
- [ 0.000000@0] loaded:268435459
- [ 0.000000@0] logo has been loaded
- [ 0.000000@0] 1080p:15
- [ 0.000000@0] full:2
- [ 0.000000@0] kernel get hdmimode form uboot is 1080p
- [ 0.000000@0] kernel get cvbsmode form uboot is 576cvbs
- [ 0.000000@0] hdmitx: cec: Function List: enable, one touch play, one touch standby, auto power by tv
- [ 0.000000@0] hdmitx: cec: HDMI aml_read_reg32(P_AO_DEBUG_REG0):0xf
- [ 0.000000@0] hdmitx: cec: HDMI hdmi_cec_func_config:0xf
- [ 0.000000@0] hdmitx: cec: Function List: enable, one touch play, one touch standby, auto power by tv
- [ 0.000000@0] hdmitx: cec: HDMI aml_read_reg32(P_AO_DEBUG_REG0):0xf
- [ 0.000000@0] hdmitx: cec: HDMI hdmi_cec_func_config:0xf
- [ 0.000000@0] PID hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000@0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000@0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000@0] Memory: 64MB 16MB 1509MB = 1589MB total
- [ 0.000000@0] Memory: 1563192k/1563192k available, 63944k reserved, 1275904K highmem
- [ 0.000000@0] Virtual kernel memory layout:
- [ 0.000000@0] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000@0] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- [ 0.000000@0] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
- [ 0.000000@0] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
- [ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- [ 0.000000@0] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- [ 0.000000@0] .text : 0xc0008000 - 0xc0b4667c (11514 kB)
- [ 0.000000@0] .init : 0xc0b47000 - 0xc0b9f000 ( 352 kB)
- [ 0.000000@0] .data : 0xc0ba0000 - 0xc0c4fc10 ( 704 kB)
- [ 0.000000@0] .bss : 0xc0c4fc10 - 0xc0ec1e2c (2505 kB)
- [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- [ 0.000000@0] Preemptible hierarchical RCU implementation.
- [ 0.000000@0] NR_IRQS:256
- [ 0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
- [ 0.000000@0] Global timer: MESON TIMER-F (c0bbe880) initialized
- [ 0.000000@0] Switching to timer-based delay loop
- [ 0.000000@0] Console: colour dummy device 80x30
- [ 0.000000@0] meson_serial_console_setup
- [ 0.000000@0] console [ttyS0] enabled
- [ 0.413504@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
- [ 0.423788@0] pid_max: default: 32768 minimum: 301
- [ 0.428658@0] Security Framework initialized
- [ 0.432884@0] Mount-cache hash table entries: 512
- [ 0.441149@0] CPU: Testing write buffer coherency: ok
- [ 0.442798@0] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200
- [ 0.448369@0] Setting up static identity map for 0xc07e2bb8 - 0xc07e2c10
- [ 0.455132@0] L310 cache controller enabled
- [ 0.459154@0] l2x0: 8 ways, 4096 sets, CACHE_ID 0x4100a0c9, Cache size: 1048576 B
- [ 0.466721@0] AUX_CTRL 0x7ec80001, PERFETCH_CTRL 0x71000007, POWER_CTRL 0x00000000
- [ 0.474847@0] TAG_LATENCY 0x00000111, DATA_LATENCY 0x00000222
- [ 0.560143@0] write pen_release: 1
- [ 0.560341@1] CPU1: Booted secondary processor
- [ 0.560352@1] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201
- [ 0.580132@0] write pen_release: 2
- [ 0.588266@2] CPU2: Booted secondary processor
- [ 0.588277@2] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202
- [ 0.600125@0] write pen_release: 3
- [ 0.608258@3] CPU3: Booted secondary processor
- [ 0.608270@3] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203
- [ 0.608335@0] Brought up 4 CPUs
- [ 0.621476@0] SMP: Total of 4 processors activated (8.00 BogoMIPS).
- [ 0.627706@0] CPU: All CPU(s) started in SVC mode.
- [ 0.632911@0] devtmpfs: initialized
- [ 0.641198@0] clkrate [ xtal ] : 24000000
- [ 0.641227@0] clkrate [ pll_sys ] : 1200000000
- [ 0.644524@0] clkrate [ pll_fixed ] : 2550000000
- [ 0.649204@0] clkrate [ pll_vid ] : 732000000
- [ 0.653632@0] TODO: clk_get_rate_hpll() is not implement in M8 now
- [ 0.659779@0] clkrate [ pll_hpll ] : 0
- [ 0.663598@0] clkrate [ pll_ddr ] : 0
- [ 0.667321@0] clkrate [ a9_clk ] : 1200000000
- [ 0.671747@0] clkrate [ clk81 ] : 141666666
- [ 0.676992@0] pinctrl core: initialized pinctrl subsystem
- [ 0.681683@0] regulator-dummy: no parameters
- [ 0.686449@0] NET: Registered protocol family 16
- [ 0.695981@0] DMA: preallocated 4096 KiB pool for atomic coherent allocations
- [ 0.699516@0] VPU driver version: v03
- [ 0.701129@0] vpu driver detect cpu type: m8m2
- [ 0.705538@0] load vpu_clk in dts: 364000000Hz(7)
- [ 0.710285@0] vpu_probe OK
- [ 0.713362@0] cma: Assigned CMA region with name cma_0 to amvenc_avc.0 device
- [ 0.724156@0] amlogic_gpio gpio: Probed amlogic GPIO driver
- [ 0.726025@0] register lm device lm-root
- [ 0.729538@0] register lm device lm1
- [ 0.733111@0] register lm device lm0
- [ 0.736797@0] Init pinux probe!
- [ 0.740190@0] pinmux-m8 pinmux: Probed amlogic pinctrl driver
- [ 0.745484@0] tv_init_module
- [ 0.748279@0] major number 254 for disp
- [ 0.752096@0] vout_register_server
- [ 0.755465@0] register tv module server ok
- [ 0.759612@0] major number 0 for disp
- [ 0.763276@0] register tv module server ok
- [ 0.767603@0] aml_i2c version: 20140813
- [ 0.771381@0] plat->state_name:default
- [ 0.771392@0] master_no = 0, master_regs=fe600500
- [ 0.771522@0] aml-i2c i2c-AO: add adapter aml_i2c_adap0(ed8350a8)
- [ 0.777398@0] aml-i2c i2c-AO: aml i2c bus driver.
- [ 0.782178@0] plat->state_name:default
- [ 0.782189@0] master_no = 1, master_regs=fe108500
- [ 0.782288@0] aml-i2c i2c-A: add adapter aml_i2c_adap1(ed835ca8)
- [ 0.788059@0] aml-i2c i2c-A: aml i2c bus driver.
- [ 0.792742@0] plat->state_name:default
- [ 0.792753@0] master_no = 2, master_regs=fe1087c0
- [ 0.792871@0] aml-i2c i2c-B: add adapter aml_i2c_adap2(ed8368a8)
- [ 0.798635@0] aml-i2c i2c-B: aml i2c bus driver.
- [ 0.803314@0] plat->state_name:default
- [ 0.803326@0] master_no = 3, master_regs=fe1087e0
- [ 0.803422@0] aml-i2c i2c-C: add adapter aml_i2c_adap3(ed8374a8)
- [ 0.809210@0] aml-i2c i2c-C: aml i2c bus driver.
- [ 0.813992@0] aml_pmu_init, 454
- [ 0.816987@0] call aml_dvfs_init in
- [ 0.820441@0] [DVFS]aml_dvfs_probe, child name:vcck_dvfs
- [ 0.820449@0] [DVFS]dvfs table of vcck_dvfs is:
- [ 0.820454@0] [DVFS] freq, min_uV, max_uV
- [ 0.820459@0] [DVFS] 96000, 825000, 825000
- [ 0.820464@0] [DVFS] 192000, 825000, 825000
- [ 0.820468@0] [DVFS] 312000, 825000, 825000
- [ 0.820472@0] [DVFS] 408000, 825000, 825000
- [ 0.820476@0] [DVFS] 504000, 825000, 825000
- [ 0.820480@0] [DVFS] 600000, 850000, 850000
- [ 0.820485@0] [DVFS] 720000, 850000, 850000
- [ 0.820489@0] [DVFS] 816000, 875000, 875000
- [ 0.820493@0] [DVFS] 1008000, 925000, 925000
- [ 0.820498@0] [DVFS] 1200000, 975000, 975000
- [ 0.820502@0] [DVFS] 1416000, 1025000, 1025000
- [ 0.820506@0] [DVFS] 1608000, 1100000, 1100000
- [ 0.820510@0] [DVFS] 1800000, 1125000, 1125000
- [ 0.820515@0] [DVFS] 1992000, 1150000, 1150000
- [ 0.820664@0] hdmitx: system: amhdmitx_init
- [ 0.824551@0] hdmitx: system: Ver: 2014May6
- [ 0.828766@0] hdmitx: system: amhdmitx_probe
- [ 0.833188@0] hdmitx: system: not find cec config
- [ 0.837640@0] hdmitx: system: not find vend_init_data
- [ 0.842901@0] hdmitx: system: gate/pwr cmd: 7
- [ 0.847003@0] hdmitx: system: ALREADY init VIC = 16
- [ 0.851866@0] hdmitx: system: gate/pwr cmd: 0
- [ 0.856560@1] hdmitx: system: reset intr mask
- [ 0.880380@0] hdmitx: system: irq 1
- [ 0.922044@0] bio: create slab <bio-0> at 0
- [ 0.922778@0] SCSI subsystem initialized
- [ 0.924835@0] usbcore: registered new interface driver usbfs
- [ 0.930230@0] usbcore: registered new interface driver hub
- [ 0.935709@0] usbcore: registered new device driver usb
- [ 0.940925@0] Linux video capture interface: v2.00
- [ 0.945771@0] pps_core: LinuxPPS API ver. 1 registered
- [ 0.950680@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 0.960000@0] PTP clock support registered
- [ 0.964701@0] mode is 15,sync_duration_den=1,sync_duration_num=60
- [ 0.970102@0] TV mode 1080p selected.
- [ 0.973726@0] already display in uboot
- [ 0.979511@0] call aml_pmu_probe_init in
- [ 0.981420@0] aml_pmus_probe, child name:rn5t618
- [ 0.985948@0] aml_pmus_probe, i2c_bus:i2c_bus_ao
- [ 0.990839@0] [RICOH]setup_supply_data, failed to get property: board_battery
- [ 0.997657@0] [DVFS]aml_dvfs_register_driver, driver rn5t618-dvfs regist success, mask:7, source id:1
- [ 0.997663@0] [RN5T618]ricoh_pmu_probe, 283
- [ 0.998282@0] [RN5T618]coulomb_flag:0x20
- [ 0.998287@0] [RN5T618]no saved coulomb counter
- [ 0.998387@0] ricoh_pmu_probe, 298
- [ 0.998396@0] Allocate new i2c device: adapter:0, addr:0x32, node name:rn5t618, type:ricoh_pmu
- [ 1.000759@1] hdmitx: system: gate/pwr cmd: 4
- [ 1.010996@0] Advanced Linux Sound Architecture Driver Initialized.
- [ 1.017264@0] Bluetooth: Core ver 2.16
- [ 1.020628@0] NET: Registered protocol family 31
- [ 1.025128@0] Bluetooth: HCI device and connection manager initialized
- [ 1.031647@0] Bluetooth: HCI socket layer initialized
- [ 1.036660@0] Bluetooth: L2CAP socket layer initialized
- [ 1.041880@0] Bluetooth: SCO socket layer initialized
- [ 1.047139@0] cfg80211: Calling CRDA to update world regulatory domain
- [ 1.053474@0] cfg80211: World regulatory domain updated:
- [ 1.058703@0] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 1.060094@1] Switching to clocksource Timer-E
- [ 1.071449@0] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (2000 mBi, 0 mBm)
- [ 1.079133@0] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (2000 mBi, 0 mBm)
- [ 1.086874@0] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (2000 mBi, 0 mBm)
- [ 1.090899@2] NET: Registered protocol family 2
- [ 1.091325@2] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
- [ 1.091371@2] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
- [ 1.091411@2] TCP: Hash tables configured (established 4096 bind 4096)
- [ 1.091467@2] TCP: reno registered
- [ 1.091473@2] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 1.091486@2] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 1.091609@2] NET: Registered protocol family 1
- [ 1.139668@0] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (2000 mBi, 0 mBm)
- [ 1.139774@2] RPC: Registered named UNIX socket transport module.
- [ 1.139776@2] RPC: Registered udp transport module.
- [ 1.139777@2] RPC: Registered tcp transport module.
- [ 1.139779@2] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 1.139836@2] wifi_dev_probe
- [ 1.139840@2] wifi_dt : interrupt_pin=GPIOX_21
- [ 1.139845@2] wifi_dt : irq_num=null
- [ 1.139847@2] wifi_dt : irq_trigger_type=GPIO_IRQ_HIGH
- [ 1.139850@2] wifi_dt : power_on_pin=GPIOAO_6
- [ 1.139854@2] wifi_dt : power_on_pin2=GPIOX_11
- [ 1.139861@2] interrupt_pin=133, irq_num=4, irq_trigger_type=0, power_on_pin=6,clock_32k_pin=122
- [ 1.140028@2] Unpacking initramfs...
- [ 1.147235@2] Freeing initrd memory: 3372K (c4e09000 - c5154000)
- [ 1.149030@2] audit: initializing netlink socket (disabled)
- [ 1.149049@2] type=2000 audit(1.030:1): initialized
- [ 1.149330@1] balance_pgdat end zone=0, pgdat_is_balanced=0
- [ 1.149428@2] bounce pool size: 64 pages
- [ 1.154626@2] VFS: Disk quotas dquot_6.5.2
- [ 1.154812@2] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 1.156472@2] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 1.157585@2] NFS: Registering the id_resolver key type
- [ 1.157603@2] Key type id_resolver registered
- [ 1.157605@2] Key type id_legacy registered
- [ 1.157990@2] fuse init (API version 7.22)
- [ 1.158523@2] msgmni has been set to 623
- [ 1.159503@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
- [ 1.159507@2] io scheduler noop registered
- [ 1.159509@2] io scheduler deadline registered
- [ 1.159655@2] io scheduler cfq registered (default)
- [ 1.286330@0] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (2000 mBi, 0 mBm)
- [ 1.286333@0] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (2000 mBi, 0 mBm)
- [ 1.286336@0] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (2000 mBi, 0 mBm)
- [ 1.286339@0] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
- [ 1.291779@1] hdmitx: system: gate/pwr cmd: 5
- [ 1.291781@1] hdmitx: edid: edid ready
- [ 1.291783@1] hdmitx: system: gate/pwr cmd: 4
- [ 1.332672@2] loop: module loaded
- [ 1.333553@2] tun: Universal TUN/TAP device driver, 1.6
- [ 1.338051@2] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- [ 1.344550@2] PPP generic driver version 2.4.2
- [ 1.348985@2] PPP BSD Compression module registered
- [ 1.353666@2] PPP Deflate Compression module registered
- [ 1.358861@2] PPP MPPE Compression module registered
- [ 1.364200@2] NET: Registered protocol family 24
- [ 1.368507@2] usbcore: registered new interface driver asix
- [ 1.374053@2] usbcore: registered new interface driver ax88179_178a
- [ 1.380257@2] usbcore: registered new interface driver cdc_ether
- [ 1.386254@2] usbcore: registered new interface driver dm9601
- [ 1.392067@2] usbcore: registered new interface driver net1080
- [ 1.397765@2] usbcore: registered new interface driver cdc_subset
- [ 1.403844@2] usbcore: registered new interface driver zaurus
- [ 1.409569@2] usbcore: registered new interface driver cdc_ncm
- [ 1.415665@2] usbcore: registered new interface driver usb-storage
- [ 1.421706@2] mousedev: PS/2 mouse device common for all mice
- [ 1.427278@2] i2c /dev entries driver
- [ 1.431564@2] usbcore: registered new interface driver uvcvideo
- [ 1.436695@2] USB Video Class driver (1.1.1)
- [ 1.441228@2] device-mapper: uevent: version 1.0.3
- [ 1.446001@2] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
- [ 1.454490@2] Bluetooth: HCI UART driver ver 2.2
- [ 1.458887@2] Bluetooth: HCI H4 protocol initialized
- [ 1.463939@2] usbcore: registered new interface driver btusb
- [ 1.469462@2] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
- [ 1.475828@2] hidraw: raw HID events driver (C) Jiri Kosina
- [ 1.485828@2] usbcore: registered new interface driver usbhid
- [ 1.486538@2] usbhid: USB HID core driver
- [ 1.490918@2] zram: Created 1 device(s) ...
- [ 1.495056@2] ashmem: initialized
- [ 1.498132@2] logger: created 256K log 'log_main'
- [ 1.501769@1] hdmitx: system: gate/pwr cmd: 5
- [ 1.501771@1] hdmitx: edid: edid ready
- [ 1.501776@1] hdmitx: edid: check sum valid
- [ 1.501777@1] hdmitx: edid: check sum valid
- [ 1.501779@1] hdmitx: edid: blk0 raw data
- [ 1.501802@1] 00ffffffffffff004c2d86043332464330130103801009782aee91a3544c9926
- [ 1.501823@1] 0f5054bfef80714f8100814081809500a940b3000101023a801871382d40582c
- [ 1.501844@1] 4500a05a0000001e011d00bc52d01e20b8285540a05a0000001e000000fd0017
- [ 1.501864@1] 4b1b5111000a202020202020000000fc0053796e634d61737465720a20200173
- [ 1.501865@1]
- [ 1.501866@1] hdmitx: edid: blk1 raw data
- [ 1.501887@1] 020321f14d9304120314052021221f100716230907078301000066030c001000
- [ 1.501908@1] 808c0ad08a20e02d10103e9600a05a00000018011d007251d01e206e285500a0
- [ 1.501928@1] 5a0000001e011d80d0721c1620102c2580a05a0000009e011d8018711c162058
- [ 1.501949@1] 2c2500a05a0000009e8c0ad090204031200c405500a05a000000180000000091
- [ 1.501950@1]
- [ 1.501981@1] hdmitx: edid: find IEEEOUT
- [ 1.502015@1] hdmitx: video: get current mode: 1080p
- [ 1.502023@1] is_similar_hdmi_vic[324] vic_old=16,mode_new=15
- [ 1.502025@1] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16
- [ 1.502028@1] hdmitx: audio: audio channel num is 0
- [ 1.502033@1] hdmitx: audio: SPDIF
- [ 1.502045@1] hdmitx: audio: current VIC: 16
- [ 1.502046@1] hdmitx: audio: audio sample rate: 0
- [ 1.502048@1] hdmitx: audio: set audio N para
- [ 1.502055@1] hdmitx: audio: PCM out to HDMI
- [ 1.522534@1] hdmitx: audio: Time out: AIU_HDMI_CLK_DATA_CTRL
- [ 1.522536@1] hdmitx: audio: i2s_to_spdif_flag:1
- [ 1.522537@1] hdmitx: audio: Enable audio spdif to HDMI
- [ 1.522590@1] hdmitx: cec: CEC not ready
- [ 1.654543@2] logger: created 256K log 'log_events'
- [ 1.659367@2] logger: created 256K log 'log_radio'
- [ 1.664151@2] logger: created 256K log 'log_system'
- [ 1.669108@2] vout_init_module
- [ 1.671919@2] start init vout module
- [ 1.675672@2] create vout attribute ok
- [ 1.680063@2] ge2d_init
- [ 1.682022@2] ge2d_dev major:244
- [ 1.685497@2] ge2d start monitor
- [ 1.688626@2] osd_init
- [ 1.688631@0] ge2d workqueue monitor start
- [ 1.695132@2] osd_probe, vinfo:c0835c34
- [ 1.699407@2] Frame buffer memory assigned at phy:0x06100000, vir:0xf1000000, size=73728K
- [ 1.707490@2] osd_probe, mydef_var:c0bfd728, vinfo:c0835c34
- [ 1.712620@2] init fbdev bpp is :32
- [ 1.716159@2] ---------------clear framebuffer0 memory
- [ 1.770642@0] Console: switching to colour frame buffer device 240x67
- [ 1.797149@0] Frame buffer memory assigned at phy:0x0a900000, vir:0xf0200000, size=1024K
- [ 1.802944@0] osd_probe, mydef_var:c0bfd728, vinfo:c0835c34
- [ 1.808482@0] don't find to display_size_default from mesonfb-dts
- [ 1.814559@0] init fbdev bpp is :16
- [ 1.830406@0] osd probe ok
- [ 1.830578@0] osd_ext_init
- [ 1.830979@0] vout2_init_module enter
- [ 1.840246@0] amlvideo-000: V4L2 device registered as video10
- [ 1.840539@0] amlvideo2: V4L2 device registered as video11
- [ 1.846132@0] ionvideo-000: V4L2 device registered as video13
- [ 1.851545@0] Video Technology Magazine Ion Video Capture Board ver 1.0 successfully loaded.
- [ 1.859938@0] DI: di_init
- [ 1.859965@0] DI: di_probe
- [ 1.860369@0] aml_wdt_driver_init,301
- [ 1.863606@0] ** disable watchdog
- [ 1.867063@0] keys===========================================
- [ 1.872620@0] keys_devno=f100000
- [ 1.876003@0] securitykey: device aml_keys created
- [ 1.880580@0] amlkeys=0
- [ 1.883100@0] platform_driver_register--aml_keys_driver--------------------
- [ 1.889992@0] key unify config unifykey-num is 6
- [ 1.894575@0] key unify fact unifykey-num is 6
- [ 1.898951@0] aml_unifykeys_probe:694=============unifykey_devno:f000000
- [ 1.905836@0] unifykey: device unifykeys created ok
- [ 1.910550@0] platform_driver_register--unifykey management driver--------------------
- [ 1.918733@0] set uart_ao pinmux use pinctrl subsystem
- [ 1.923590@0] P_AO_RTI_PIN_MUX_REG:25861
- [ 1.927476@0] start uart_ao_ttyS0:(irq = 122)
- [ 1.931825@0] register uart_ao ok
- [ 1.935308@0] set uart_a pinmux use pinctrl subsystem
- [ 1.940120@0] P_AO_RTI_PIN_MUX_REG:25861
- [ 1.944056@0] start uart_a_ttyS1:(irq = 58)
- [ 1.948184@0] register uart_a ok
- [ 1.951610@0] start uart_d_ttyS4:(irq = 126)
- [ 1.955636@0] register uart_d ok
- [ 1.958980@0] dwc_otg: version 3.10a 12-MAY-2014
- [ 1.963478@0] dwc_otg lm-root: dwc_otg_driver_probe(ed81ec00)
- [ 1.963486@0] dwc_otg_driver_probe NOT match
- [ 1.967702@0] dwc_otg lm1: dwc_otg_driver_probe(ed81ee00)
- [ 1.967717@0] usb1: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: fe108820, ctrl: fe080000
- [ 1.976295@0] USB (1) use clock source: XTAL input
- [ 1.982088@0] dwc_otg lm1: base=0xfe080000
- [ 1.982096@0] dwc_otg lm1: dwc_otg_device=0xecfb2b40
- [ 2.002127@0] Core Release: 3.10a
- [ 2.002151@0] Setting default values for core params
- [ 2.004747@0] curmode: 1, host_only: 1
- [ 2.008478@0] dwc_otg lm1: DMA config: BURST_DEFAULT
- [ 2.028576@0] Using Buffer DMA mode
- [ 2.028601@0] OTG VER PARAM: 1, OTG VER FLAG: 1
- [ 2.030936@0] Working on port type = HOST
- [ 2.035606@0] dwc_otg lm1: DWC OTG Controller
- [ 2.039270@0] dwc_otg lm1: new USB bus registered, assigned bus number 1
- [ 2.045974@0] dwc_otg lm1: irq 63, io mem 0x00000000
- [ 2.050874@0] -------hcd->flags.d32 = 0
- [ 2.054722@0] Init: Port Power? op_state=1
- [ 2.058757@0] Init1: Power Port (0)
- [ 2.062323@0] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- [ 2.069166@0] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 2.076549@0] usb usb1: Product: DWC OTG Controller
- [ 2.081386@0] usb usb1: Manufacturer: Linux 3.10.84 dwc_otg_hcd
- [ 2.087297@0] usb usb1: SerialNumber: lm1
- [ 2.091661@0] hub 1-0:1.0: USB hub found
- [ 2.095172@0] hub 1-0:1.0: 1 port detected
- [ 2.099372@0] dwc_otg lm0: dwc_otg_driver_probe(ed81f000)
- [ 2.099399@0] usb0: type: 0, speed: 0, config: 0, dma: 0, id: 0, phy: fe108800, ctrl: fe040000
- [ 2.107854@0] USB (0) use clock source: XTAL input
- [ 2.113607@0] dwc_otg lm0: base=0xfe040000
- [ 2.113615@0] dwc_otg lm0: dwc_otg_device=0xed77b400
- [ 2.133646@0] Core Release: 3.10a
- [ 2.133670@0] Setting default values for core params
- [ 2.136264@0] curmode: 1, host_only: 0
- [ 2.179964@0] dwc_otg lm0: DMA config: BURST_DEFAULT
- [ 2.200069@0] Using Buffer DMA mode
- [ 2.200094@0] OTG VER PARAM: 1, OTG VER FLAG: 1
- [ 2.202446@0] Working on port type = OTG
- [ 2.206326@0] Current port type: SLAVE
- [ 2.210168@0] dwc_otg lm0: DWC OTG Controller
- [ 2.214425@0] dwc_otg lm0: new USB bus registered, assigned bus number 2
- [ 2.221076@0] dwc_otg lm0: irq 62, io mem 0x00000000
- [ 2.226056@0] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
- [ 2.232964@0] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 2.240307@0] usb usb2: Product: DWC OTG Controller
- [ 2.245180@0] usb usb2: Manufacturer: Linux 3.10.84 dwc_otg_hcd
- [ 2.251059@0] usb usb2: SerialNumber: lm0
- [ 2.255411@0] hub 2-0:1.0: USB hub found
- [ 2.258949@0] hub 2-0:1.0: 1 port detected
- [ 2.263160@0] Dedicated Tx FIFOs mode
- [ 2.266880@0] using timer detect id change, ed97f000
- [ 2.271771@0] boot_device_flag : -1
- [ 2.275065@0] do not init nand
- [ 2.278197@0] boot_device_flag : -1
- [ 2.281663@0] ethernet_driver probe!
- [ 2.285123@0] Please config savepowermode.
- [ 2.289197@0] ethernetinit(dbg[c0c041ec]=1)
- [ 2.291605@3] HOST mode
- [ 2.295825@0] ethernet base addr is fe0c0000
- [ 2.295831@1] Indeed it is in host mode hprt0 = 00021501
- [ 2.305354@0] device name=nand_key open error
- [ 2.309739@0] aml_keys: version 0 can not be init c0c0259c
- [ 2.315222@0] ret = -22
- [ 2.315222@0] print_buff=
- [ 2.321471@3] -------hcd->flags.d32 = 0
- [ 2.321496@3] Init: Port Power? op_state=1
- [ 2.321498@3] Init1: Power Port (0)
- [ 2.321503@3] [RN5T618]rn5t618_otg_change, driver is not ready, do it later
- [ 2.321505@3] set usb port power on (board gpio 15)!
- [ 2.320227@0] write mac add to:ecf636c8: 16 84 bc 9f 78 a3 |...x.|
- [ 2.352301@0] libphy: AMLMAC MII Bus: probed
- [ 2.353948@0] eth0: PHY ID 02430c54 at 0 IRQ -1 (0:00) active
- [ 2.361643@0] Amlogic A/V streaming port init
- [ 2.365600@0] buffersize=262144,0,start=0
- [ 2.367994@0] Subtitle stbuf alloced at 0xecfc0000, size = 262144
- [ 2.374089@0] changed the (2) buffer size from 0 to 262144
- [ 2.379766@0] init vdec memsource ca00000->1c9fffff
- [ 2.384610@0] [tsync_pcr_init]init success.
- [ 2.388619@0] amvideocap_init_module
- [ 2.392469@0] regist mpeg12 codec profile
- [ 2.396248@0] regist mpeg4 codec profile
- [ 2.400065@0] amvdec_vc1 module init
- [ 2.403730@0] regist vc1 codec profile
- [ 2.407342@0] amvdec_h264 module init
- [ 2.411086@0] regist h264 codec profile
- [ 2.415012@0] amvdec_h264mvc module init
- [ 2.418799@0] regist hmvc codec profile
- [ 2.422539@0] amvdec_h264_4k2k module init
- [ 2.426682@0] regist h264_4k2k codec profile
- [ 2.430837@0] amvdec_h265 module init
- [ 2.434593@0] regist hevc codec profile
- [ 2.438378@0] regist mjpeg codec profile
- [ 2.442269@0] amvdec_real module init
- [ 2.445922@0] amvdec_avs module init
- [ 2.449585@0] amvenc_avc memory resource undefined.
- [ 2.454264@0] encode_wq_init.
- [ 2.457186@0] encode start monitor.
- [ 2.460703@0] encode workqueue monitor start.
- [ 2.465259@1] jpegenc module init
- [ 2.468543@1] alloc_keep_buffer keep_y_addr eca00000
- [ 2.473261@1] usb 1-1: new full-speed USB device number 2 using dwc_otg
- [ 2.479841@1] alloc_keep_buffer keep_u_addr ed000000
- [ 2.479957@3] Indeed it is in host mode hprt0 = 00021501
- [ 2.490059@1] alloc_keep_buffer keep_v_addr ed100000
- [ 2.495010@1] yaddr=eca00000,u_addr=ed000000,v_addr=ed100000
- [ 2.500922@1] create_ge2d_work_queue video task ok
- [ 2.505803@1]
- [ 2.505803@1]
- [ 2.505803@1] VECM init
- [ 2.505803@1]
- [ 2.513269@1] efuse===========================================
- [ 2.518983@1] efuse: device efuse created
- [ 2.522924@1] efuse--------------------------------------------
- [ 2.528697@1] SARADC Driver init.
- [ 2.532152@1] __saradc_probe__
- [ 2.673450@3] usb 1-1: New USB device found, idVendor=046d, idProduct=c52b
- [ 2.674683@3] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
- [ 2.681572@1] saradc calibration: ref_val = 507
- [ 2.681574@1] saradc calibration: ref_nominal = 512
- [ 2.681575@1] saradc calibration: coef = 4080
- [ 2.695674@3] usb 1-1: Product: USB Receiver
- [ 2.695741@1] Remote Driver
- [ 2.695812@1] Remote platform_data g_remote_base=fe600580
- [ 2.695832@1] set drvdata completed
- [ 2.695838@1] device_create_file completed
- [ 2.696135@1] input: aml_keypad as /devices/platform/meson-remote/input/input0
- [ 2.696385@1] input_register_device completed
- [ 2.696425@1] [0xffffff00] = 0x1dd0190
- [ 2.696427@1] [0xffffff04] = 0xf800ca
- [ 2.696429@1] [0xffffff08] = 0x82006e
- [ 2.696431@1] [0xffffff0c] = 0x3c0030
- [ 2.696432@1] [0xffffff10] = 0x30fa0013
- [ 2.696434@1] [0xffffff18] = 0x6f19000
- [ 2.696435@1] [0xffffff1c] = 0xbe40
- [ 2.696437@1] [0x0] = 0xfa00a0
- [ 2.696438@1] [0x4] = 0xfa00a0
- [ 2.696440@1] [0x8] = 0xfa00a0
- [ 2.696441@1] [0xc] = 0x640030
- [ 2.696443@1] [0x10] = 0x30fa0013
- [ 2.696444@1] [0x18] = 0x961b800
- [ 2.696445@1] [0x1c] = 0x9740
- [ 2.696447@1] [0x20] = 0x104
- [ 2.696448@1] [0x24] = 0x0
- [ 2.696450@1] [0x28] = 0x0
- [ 2.696452@1] set_remote_mode[69]
- [ 2.696467@1] remote config major:235
- [ 2.696654@1] physical address:0x2db9a000
- [ 2.696738@1] GPIO Keypad Driver init.
- [ 2.696803@1] ==gpio_key_probe==
- [ 2.696806@1] gpio request set to High-Z status
- [ 2.696822@1] reg:2620,clearmask=400040,setmask=1
- [ 2.696825@1] reg:2622,clearmask=ff0000,set pin=3
- [ 2.696828@1] reg:2623,clearmask=7000000,setmask=7
- [ 2.696830@1] reg:2620,clearmask=800080,setmask=10001
- [ 2.696833@1] reg:2622,clearmask=ff000000,set pin=3
- [ 2.696835@1] reg:2623,clearmask=70000000,setmask=7
- [ 2.696855@1] power key(116) registed.
- [ 2.696859@0] key 116 up
- [ 2.697005@1] input: gpio_keypad as /devices/platform/gpio_keypad.6/input/input1
- [ 2.697129@1] gpio keypad register input device completed.
- [ 2.697135@1] gpio keypad major:234
- [ 2.697395@1] spi_nor_init
- [ 2.697512@1] amlogic_spi_nor_probe:
- [ 2.697517@1] amlogic_spi->state_name:default
- [ 2.697634@1] AMLOGIC_SPI_NOR cc000000.spi: master is unqueued, this is deprecated
- [ 2.697742@1] check_storage_device : spi boot_device_flag : -1
- [ 2.697744@1] spi_nor_probe
- [ 2.697746@1] spi_nor_probe 629 boot_device_flag 2 : do not init spi
- [ 2.697753@1] spi_nor: probe of apollospi:32766 failed with error -12
- [ 2.697757@1] amlogic_spi_nor_probe over
- [ 2.697892@1] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
- [ 2.910054@3] usb 1-1: Manufacturer: Logitech
- [ 2.914834@1] host->base fe108c20
- [ 2.917710@1] pdata->caps 7
- [ 2.920447@1] pdata->caps2 0
- [ 2.923312@1] get property: port, value:0x00000001
- [ 2.929812@1] get property: ocr_avail, value:0x00200000
- [ 2.936305@1] get property: f_min, value:0x000493e0
- [ 2.942810@1] get property: f_max, value:0x02faf080
- [ 2.949299@1] get property: f_max_w, value:0x02faf080
- [ 2.950184@3] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-lm1-1/input2
- [ 2.950347@3] Indeed it is in host mode hprt0 = 00021501
- [ 2.973316@1] get property: max_req_size, value:0x00020000
- [ 2.979802@1] get property: irq_in, value:0x00000003
- [ 2.986316@1] get property: irq_out, value:0x00000005
- [ 2.992820@1] get property: gpio_cd, str:CARD_6
- [ 2.998788@1] get property: pinname, str:sd
- [ 3.004433@1] get property: jtag_pin, str:CARD_0
- [ 3.010401@1] get property: card_type, value:0x00000005
- [ 3.016916@1] get property: gpio_dat3, str:CARD_4
- [ 3.022907@1] normal card in
- [ 3.061485@1] reg:2620,clearmask=80008,setmask=10001
- [ 3.061524@1] reg:2621,clearmask=ff000000,set pin=64
- [ 3.065836@1] reg:2623,clearmask=7000,setmask=7
- [ 3.070344@1] reg:2620,clearmask=200020,setmask=1
- [ 3.075111@1] reg:2622,clearmask=ff00,set pin=64
- [ 3.079705@1] reg:2623,clearmask=700000,setmask=7
- [ 3.084520@1] pdata->caps 107
- [ 3.087333@1] pdata->caps2 0
- [ 3.090194@1] get property: port, value:0x00000000
- [ 3.090206@0] sd: new high speed SDHC card at address 0002, clock 35416666, 4-bit-bus-width
- [ 3.101676@0] mmcblk0: sd:0002 SD4GB 3.77 GiB
- [ 3.105236@0] mmcblk0: p1 p2
- [ 3.112415@1] get property: ocr_avail, value:0x00200000
- [ 3.118886@1] get property: f_min, value:0x000493e0
- [ 3.121481@3] usb 2-1: new full-speed USB device number 2 using dwc_otg
- [ 3.121771@3] Indeed it is in host mode hprt0 = 00021501
- [ 3.137275@1] get property: f_max, value:0x02faf080
- [ 3.143773@1] get property: max_req_size, value:0x00020000
- [ 3.150268@1] get property: pinname, str:sdio
- [ 3.156081@1] get property: card_type, value:0x00000003
- [ 3.251461@1] [aml_sdio_probe] aml_sdio_probe() success!
- [ 3.252691@1] host->base fe108e00
- [ 3.254472@1] pdata->caps 80000547
- [ 3.257809@1] pdata->caps2 20
- [ 3.260754@1] get property: port, value:0x00000005
- [ 3.267270@1] get property: ocr_avail, value:0x00200080
- [ 3.273775@1] get property: f_min, value:0x000493e0
- [ 3.280256@1] get property: f_max, value:0x05f5e100
- [ 3.286774@1] get property: max_req_size, value:0x00020000
- [ 3.293270@1] get property: pinname, str:emmc
- [ 3.299067@1] get property: card_type, value:0x00000001
- [ 3.305585@1] get property: gpio_dat3, str:BOOT_3
- [ 3.311568@1] [is_emmc_exist] host->storage_flag=2, POR_BOOT_VALUE=3
- [ 3.324481@3] usb 2-1: New USB device found, idVendor=046d, idProduct=c318
- [ 3.325722@3] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
- [ 3.333014@3] usb 2-1: Product: Logitech Illuminated Keyboard
- [ 3.338725@3] usb 2-1: Manufacturer: Logitech
- [ 3.345876@3] input: Logitech Logitech Illuminated Keyboard as /devices/lm0/usb2/2-1/2-1:1.0/input/input2
- [ 3.351475@0] aml_emmc_hw_reset 1340
- [ 3.356467@3] hid-generic 0003:046D:C318.0004: input,hidraw1: USB HID v1.11 Keyboard [Logitech Logitech Illuminated Keyboard] on usb-lm0-1/input0
- [ 3.359179@1] mmc_init_card
- [ 3.376282@3] input: Logitech Logitech Illuminated Keyboard as /devices/lm0/usb2/2-1/2-1:1.1/input/input3
- [ 3.381892@3] hid-generic 0003:046D:C318.0005: input,hiddev0,hidraw2: USB HID v1.11 Device [Logitech Logitech Illuminated Keyboard] on usb-lm0-1/input1
- [ 3.414631@1] emmc: BKOPS_EN bit is not set
- [ 3.414659@1] ###check hw reset function is already enabled here
- [ 3.419820@1] Activate high speed
- [ 3.422493@1] [aml_sdhc_probe] aml_sdhc_probe() success!
- [ 3.427874@1] [dsp]DSP start addr 0xc5e00000
- [ 3.432029@1] [dsp]register dsp to char divece(257)
- [ 3.437307@1] amlogic audio spdif interface device init!
- [ 3.442227@3] emmc: new high speed MMC card at address 0001, clock 47222222, 8-bit-bus-width
- [ 3.442246@1] device name=nand_key open error
- [ 3.442250@1] aml_keys: version 0 can not be init c0c0259c
- [ 3.442251@1] device name=emmc_key open error
- [ 3.442253@1] aml_keys: version 0 can not be init c0c0259c
- [ 3.470508@1] aml_rtc rtc.0: rtc core: registered aml_rtc as rtc0
- [ 3.470653@3] mmcblk1: emmc:0001 NCard 7.21 GiB
- [ 3.470767@3] mmcblk1boot0: emmc:0001 NCard partition 1 2.00 MiB
- [ 3.470866@3] mmcblk1boot1: emmc:0001 NCard partition 2 2.00 MiB
- [ 3.493269@3] mmcblk1: p1
- [ 3.494232@1] [AML1216]call aml1216_battery_init, ret = 0
- [ 3.494325@1] [AML1218]call aml1218_battery_init, ret = 0
- [ 3.494517@1] [RN5T618]call rn5t618_battery_probe in
- [ 3.494517@1] input: rn5t618_pmu as /devices/i2c-0/0-0032/rn5t618_pmu.0/input/input4
- [ 3.503736@1] [RN5T618]use BSP configed battery parameters
- [ 3.503744@1] [RN5T618] NO BATTERY_PARAMETERS FOUND
- [ 3.504023@3] Delete invalid mbr partition part ecf61c00, part->partno 1
- [ 3.515148@1] [RN5T618]rn5t618_otg_change, value:1, is_short:0
- [ 3.515152@3] emmc read lba=0x12000, blocks=0x1 OK!
- [ 3.525801@3] emmc read lba=0x12001, blocks=0x1 OK!
- [ 3.526113@1] [RN5T618]set boost en bit, val:33
- [ 3.526643@1] register 0xB3:33
- [ 3.529043@1] ------------[ cut here ]------------
- [ 3.529054@1] WARNING: at kernel/workqueue.c:1368 __queue_work+0x248/0x368()
- [ 3.529057@1] Modules linked in:
- [ 3.529062@1] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.10.84 #1
- [ 3.529078@1] [<c0014d64>] (unwind_backtrace+0x0/0xec) from [<c0011d84>] (show_stack+0x10/0x14)
- [ 3.529087@1] [<c0011d84>] (show_stack+0x10/0x14) from [<c0032188>] (warn_slowpath_common+0x54/0x6c)
- [ 3.529094@1] [<c0032188>] (warn_slowpath_common+0x54/0x6c) from [<c003223c>] (warn_slowpath_null+0x1c/0x24)
- [ 3.529101@1] [<c003223c>] (warn_slowpath_null+0x1c/0x24) from [<c004b6cc>] (__queue_work+0x248/0x368)
- [ 3.529108@1] [<c004b6cc>] (__queue_work+0x248/0x368) from [<c004b82c>] (queue_work_on+0x40/0x4c)
- [ 3.529119@1] [<c004b82c>] (queue_work_on+0x40/0x4c) from [<c0543b68>] (rn5t618_otg_change+0x184/0x1ac)
- [ 3.529127@1] [<c0543b68>] (rn5t618_otg_change+0x184/0x1ac) from [<c0543e3c>] (rn5t618_battery_probe+0x2ac/0x5b0)
- [ 3.529136@1] [<c0543e3c>] (rn5t618_battery_probe+0x2ac/0x5b0) from [<c03158c0>] (driver_probe_device+0xd4/0x21c)
- [ 3.529144@1] [<c03158c0>] (driver_probe_device+0xd4/0x21c) from [<c0315ab4>] (__driver_attach+0x68/0x8c)
- [ 3.529150@1] [<c0315ab4>] (__driver_attach+0x68/0x8c) from [<c0313d68>] (bus_for_each_dev+0x4c/0xa4)
- [ 3.529156@1] [<c0313d68>] (bus_for_each_dev+0x4c/0xa4) from [<c0314fa8>] (bus_add_driver+0xd0/0x25c)
- [ 3.529162@1] [<c0314fa8>] (bus_add_driver+0xd0/0x25c) from [<c03160d0>] (driver_register+0xa8/0x140)
- [ 3.529168@1] [<c03160d0>] (driver_register+0xa8/0x140) from [<c05426f4>] (rn5t618_battery_init+0x10/0x34)
- [ 3.529176@1] [<c05426f4>] (rn5t618_battery_init+0x10/0x34) from [<c0008544>] (do_one_initcall+0xa0/0x148)
- [ 3.529184@1] [<c0008544>] (do_one_initcall+0xa0/0x148) from [<c0b47bdc>] (kernel_init_freeable+0x130/0x218)
- [ 3.529194@1] [<c0b47bdc>] (kernel_init_freeable+0x130/0x218) from [<c07d4adc>] (kernel_init+0x8/0x160)
- [ 3.529203@1] [<c07d4adc>] (kernel_init+0x8/0x160) from [<c000e0a0>] (ret_from_fork+0x14/0x34)
- [ 3.529215@1] ---[ end trace b3c226e2ddff0635 ]---
- [ 3.634364@2] [RN5T618]call rn5t618_battery_probe exit, ret:0
- [ 3.634364@2] [RN5T618]call rn5t618_battery_init, ret = 0
- [ 3.634434@2] vdin_drv_init: major 232
- [ 3.722980@3] [mmc_read_partition_tbl] mmc read partition OK!
- [ 3.723063@2] vdin0 mem_start = 0x1ca00000, mem_size = 0x100000
- [ 3.723074@2] vdin_drv_probe: driver initialized ok
- [ 3.739427@3] add_emmc_partition
- [ 3.739530@2] vdin1 mem_start = 0x1cb00000, mem_size = 0x1000000
- [ 3.739540@2] vdin_drv_probe: driver initialized ok
- [ 3.739672@2] amvdec_656in module: init.
- [ 3.739677@2] amvdec_656in_init_module:major 231
- [ 3.762074@2] amvdec_656in probe ok.
- [ 3.765513@3] [mmcblk1p01] bootloader offset 0x000000000000, size 0x000000400000
- [ 3.765913@2] amvdec_csi probe ok.
- [ 3.765979@2] [viuin..]viuin_init_module viuin module init
- [ 3.766199@2] [viuin..]viuin_probe probe ok.
- [ 3.766569@2] [isp..]isp_probe isp probe ok.
- [ 3.766631@2] [sii9233a_drv_init] Ver: 2013Nov12
- [ 3.767785@2] amaudio2: device amaudio2 created
- [ 3.767965@2] Error: Didn't get power valid value --- wifi_power_probe 323
- [ 3.767970@2] wifi_power power_gpio is 6
- [ 3.767973@2] wifi_power power_gpio2 is 123
- [ 3.768264@2] amlogic rfkill init
- [ 3.768302@2] enter bt_probe of_node
- [ 3.768307@2] not get gpio_en
- [ 3.768308@2] not get gpio_wake
- [ 3.791582@2] wifi_request_32k_clk : OFF-->ON for bt_rfkill
- [ 3.791585@2] clock_32k_pin(122) : (null)
- [ 3.791594@2] clock_32k_pin(122) : sdio_wifi
- [ 3.838579@3] [mmcblk1p02] reserved offset 0x000002400000, size 0x000004000000
- [ 3.846958@3] [mmcblk1p03] cache offset 0x000006c00000, size 0x000020000000
- [ 3.855384@3] [mmcblk1p04] env offset 0x000027400000, size 0x000000800000
- [ 3.863782@3] [mmcblk1p05] logo offset 0x000028400000, size 0x000002000000
- [ 3.872167@3] [mmcblk1p06] recovery offset 0x00002ac00000, size 0x000002000000
- [ 3.880560@3] [mmcblk1p07] misc offset 0x00002d400000, size 0x000002000000
- [ 3.889002@3] [mmcblk1p08] boot offset 0x00002fc00000, size 0x000002000000
- [ 3.897390@3] [mmcblk1p09] system offset 0x000032400000, size 0x000040000000
- [ 3.905819@3] [mmcblk1p10] data offset 0x000072c00000, size 0x00015b500000
- [ 3.914076@3] card key: card_blk_probe.
- [ 3.917946@3] emmc_key_init:428 emmc key lba_start:0x12020,lba_end:0x12220
- [ 3.924903@3] i=0,register --- emmc_key
- [ 3.928692@3] emmc key: emmc_key_init:450 ok.
- [ 3.933199@3] Exit aml_emmc_partition_ops OK.
- [ 3.938641@3] mmcblk1boot1: p1
- [ 3.940576@3] mmcblk1boot1: p1 start 16065 is beyond EOD, truncated
- [ 3.948166@3] mmcblk1boot0: p1
- [ 3.949933@3] mmcblk1boot0: p1 start 16065 is beyond EOD, truncated
- [ 3.963112@2] UMP: UMP device driver 0000 loaded
- [ 3.963458@2] aml_hw_crypto initialization.
- [ 3.966776@2] usbcore: registered new interface driver snd-usb-audio
- [ 3.973050@2] enter rt5616_modinit
- [ 3.976351@2] == ES8323 == es8323_modinit()
- [ 3.980718@2] enter aml_i2s_dai_probe
- [ 3.980725@2] i2s get no clk src setting in dts, use the default mpll 0
- [ 3.986819@2] [aml-i2s-dai]enterd aml_i2s_dai_probe,old_samplerate:0,sample_rate=48000
- [ 3.994857@2] enter aml_pcm_dai_probe
- [ 3.994945@2] [aml-spdif-dai]enter aml_dai_spdif_init
- [ 3.999796@2] [aml-spdif-dai]enterd aml_spdif_play,set_clock:-1,sample_rate=4
- [ 4.006919@2] audio_set_958_clk, freq=4,
- [ 4.010807@2] IEC958 16bit
- [ 4.013502@2] hdmitx: audio: aout notify rate 48000
- [ 4.018344@2] hdmitx: audio: aout notify size 16
- [ 4.022946@2] hdmitx: audio: aout notify format CT_PCM
- [ 4.028053@2] hdmitx: audio: audio channel num is 1
- [ 4.032916@2] hdmitx: audio: SPDIF
- [ 4.036295@2] hdmitx: audio: current VIC: 16
- [ 4.040534@2] hdmitx: audio: audio sample rate: 3
- [ 4.045221@2] hdmitx: audio: set audio N para
- [ 4.049553@2] hdmitx: audio: PCM out to HDMI
- [ 4.053803@2] hdmitx: audio: i2s_to_spdif_flag:1
- [ 4.058477@2] hdmitx: audio: Enable audio spdif to HDMI
- [ 4.063687@2] hdmitx: audio: Audio Type: PCM
- [ 4.067966@2] hdmitx: audio: set audio param
- [ 4.072259@2] [aml-spdif-dai]aml_spdif_probe
- [ 4.076674@2] test codec dummy_codec
- [ 4.080062@2] test_codec_of_node, node dummy_codec disable
- [ 4.085532@2] no external codec, using aml default codec
- [ 4.090951@2] enter spdif_dit_probe
- [ 4.094372@2] aml_spdif_unmute
- [ 4.097679@2] codec_name = aml_m8_codec.0
- [ 4.101928@0] enter aml_set_bias_level level: 1
- [ 4.101949@0] enter aml_set_bias_level level: 1
- [ 4.101955@0] enter aml_set_bias_level level: 2
- [ 4.101992@2] enter aml_asoc_init
- [ 4.102018@2] p_aml_audio->hp_disable=1
- [ 4.105287@2] falied to get spk event delay time paraments from dts file
- [ 4.111970@2] spk_event delay_time = 0
- [ 4.116758@2] aml-i2s 0:playback preallocate_dma_buffer: area=ef300000, addr=2f500000, size=524288
- [ 4.124951@2] aml-i2s 1:capture preallocate_dma_buffer: area=ef240000, addr=2f440000, size=65536
- [ 4.133396@2] aml_snd_m8 aml_m8_sound_card.5: AML-M8 <-> aml-i2s-dai.0 mapping ok
- [ 4.140972@2] enter aml_set_bias_level level: 1
- [ 4.140978@2] enter aml_set_bias_level level: 2
- [ 4.142177@2] aml-i2s 0:playback preallocate_dma_buffer: area=ef400000, addr=2f600000, size=524288
- [ 4.150135@2] aml-i2s 1:capture preallocate_dma_buffer: area=ef260000, addr=2f460000, size=65536
- [ 4.158634@2] aml_snd_m8 aml_m8_sound_card.5: dit-hifi <-> aml-spdif-dai.0 mapping ok
- [ 4.166566@2] enter aml_set_bias_level level: 1
- [ 4.166571@2] enter aml_set_bias_level level: 2
- [ 4.166646@2] enter aml_set_bias_level level: 1
- [ 4.166651@2] enter aml_set_bias_level level: 2
- [ 4.167473@2] enter aml_set_bias_level level: 1
- [ 4.167480@2] enter aml_set_bias_level level: 2
- [ 4.167559@2] -----ext_codec=0---
- [ 4.169789@2] =aml_m8_pinmux_init==,aml_m8_pinmux_init done,---0
- [ 4.175920@2] Netfilter messages via NETLINK v0.30.
- [ 4.180646@2] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
- [ 4.187333@2] ctnetlink v0.93: registering with nfnetlink.
- [ 4.192371@2] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
- [ 4.199423@2] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
- [ 4.205896@2] xt_time: kernel timezone is -0000
- [ 4.209988@2] ipip: IPv4 over IPv4 tunneling driver
- [ 4.215313@2] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 4.220328@2] arp_tables: (C) 2002 David S. Miller
- [ 4.225038@2] TCP: cubic registered
- [ 4.228461@2] Initializing XFRM netlink socket
- [ 4.233450@2] NET: Registered protocol family 10
- [ 4.237996@2] mip6: Mobile IPv6
- [ 4.240617@2] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 4.246285@2] sit: IPv6 over IPv4 tunneling driver
- [ 4.251877@2] NET: Registered protocol family 17
- [ 4.255530@2] NET: Registered protocol family 15
- [ 4.260146@2] Bridge firewalling registered
- [ 4.264349@2] Bluetooth: RFCOMM TTY layer initialized
- [ 4.269302@2] Bluetooth: RFCOMM socket layer initialized
- [ 4.274588@2] Bluetooth: RFCOMM ver 1.11
- [ 4.278479@2] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- [ 4.283946@2] Bluetooth: BNEP filters: protocol multicast
- [ 4.289318@2] Bluetooth: BNEP socket layer initialized
- [ 4.294435@2] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- [ 4.300499@2] Bluetooth: HIDP socket layer initialized
- [ 4.305661@2] l2tp_core: L2TP core driver, V2.0
- [ 4.310124@2] l2tp_ppp: PPPoL2TP kernel driver, V2.0
- [ 4.315065@2] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
- [ 4.320790@2] l2tp_netlink: L2TP netlink interface
- [ 4.325576@2] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
- [ 4.331631@2] l2tp_debugfs: L2TP debugfs support
- [ 4.336207@2] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
- [ 4.342835@2] NET: Registered protocol family 35
- [ 4.347433@2] Key type dns_resolver registered
- [ 4.352675@2] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
- [ 4.359623@2] Registering SWP/SWPB emulation handler
- [ 4.364563@2] enter meson_pm_init
- [ 4.367961@2] enter meson_pm_probe!
- [ 4.371318@2] meson_pm_probe done !
- [ 4.375301@2] regulator-dummy: disabling
- [ 4.379154@2] aml_rtc rtc.0: setting system clock to 1972-04-21 18:42:51 UTC (72729771)
- [ 4.386687@2] ### dt-test ### No testcase data in device tree; not running tests
- [ 4.394117@2] meson_cpufreq: no voltage_control prop
- [ 4.398965@2] voltage_control = 0
- [ 4.403325@2] hdmitx: cec: CEC init
- [ 4.405761@1] hdmitx: cec: CEC task process
- [ 4.405897@2] input: cec_input as /devices/virtual/input/input5
- [ 4.406028@2] hdmitx: cec: hdmitx_device->cec_init_ready:0x1
- [ 4.406028@2] ALSA device list:
- [ 4.406030@2] #0: AML-M8AUDIO
- [ 4.427716@2] config uart_ao_ttyS0:: Character length 8bits/char
- [ 4.441448@2] Changing uart_ao_ttyS0: baud from 0 to 115200
- [ 4.461594@2] Freeing unused kernel memory: 352K (c0b47000 - c0b9f000)
- [ 5.760172@1] tvmode set to 720p
- [ 5.760172@1]
- [ 5.760209@1] mode is 11,sync_duration_den=1,sync_duration_num=60
- [ 5.765578@1] TV mode 720p selected.
- [ 5.769120@1] tvoutc_setmode[489]
- [ 5.772418@1] new mode 720p
- [ 5.772418@1] set ok
- [ 5.777443@1] hdmitx: video: get current mode: 720p
- [ 5.782301@1] is_similar_hdmi_vic[324] vic_old=16,mode_new=11
- [ 5.788017@1] hdmitx: video: get current mode: 720p
- [ 5.792881@1] is_similar_hdmi_vic[324] vic_old=16,mode_new=11
- [ 5.798592@1] hdmitx: system: gate/pwr cmd: 7
- [ 5.802971@1] hdmitx: system: already init VIC = 0 Now VIC = 4
- [ 5.808821@1] hdmitx: system: 4 (cd0,cs0,pm1,vd0,1)
- [ 5.813851@1] hdmitx: system: gate/pwr cmd: 0
- [ 5.818182@1] hdmitx: system: hw reset
- [ 5.822962@1] hdmitx: audio: SPDIF
- [ 5.825339@1] hdmitx: system: reconfig packet setting done
- [ 5.961453@1] hdmitx: system: phy setting done
- [ 5.981463@1] hdmitx: system: set pll
- [ 5.981482@1] hdmitx: system: param->VIC:4
- [ 5.983558@1] mode is: 11
- [ 5.986158@1] VPU_VIU_VENC_MUX_CTRL: 0x22a
- [ 5.990231@1] viu chan = 1
- [ 5.992923@1] VPU_VIU_VENC_MUX_CTRL: 0x22a
- [ 5.996992@1] config HPLL
- [ 5.999593@1] set_hpll_clk_out[62] clk = 2970
- [ 6.021449@1] config HPLL done
- [ 6.021471@1] enc_vpu_bridge_reset[292]
- [ 6.161455@0] hdmitx: system: phy setting done
- [ 6.161478@0] Sink is HDMI device
- [ 6.163552@0] No sink attached
- [ 6.166617@0] hdmitx: audio: audio channel num is 1
- [ 6.171458@0] hdmitx: audio: SPDIF
- [ 6.174834@0] hdmitx: audio: current VIC: 4
- [ 6.178979@0] hdmitx: audio: audio sample rate: 3
- [ 6.183676@0] hdmitx: audio: set audio N para
- [ 6.187998@0] hdmitx: audio: PCM out to HDMI
- [ 6.192262@0] hdmitx: audio: i2s_to_spdif_flag:1
- [ 6.196922@0] hdmitx: audio: Enable audio spdif to HDMI
- [ 6.202139@0] hdmitx: audio: Audio Type: PCM
- [ 6.207026@0] set_vout_mode[249]
- [ 6.288739@0] vfm_map_store:rm default
- [ 6.288739@0]
- [ 6.288812@0] vfm_map_store:add default decoder ppmgr deinterlace amvideo
- [ 6.288812@0]
- [ 6.617358@1] EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
- [ 6.621925@1] EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
- [ 6.631263@1] force enable DISCARD here for ext4 fs
- [ 6.653835@1] checked enable EXT4 DISCARD here
- [ 6.653862@1] EXT4-fs (mmcblk0p2): mounting with "discard" option, but the device does not support discard
- [ 6.662291@1] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
- [ 13.636403@1] systemd[1]: Failed to insert module 'autofs4'
- [ 13.639535@1] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.639782@1] systemd[1]: systemd 219 running in system mode. (-PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK -SYSVINIT -UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL -XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN)
- [ 13.652533@1] systemd[1]: Detected architecture 'arm'.
- [ 13.657488@1] systemd[1]: Running with unpopulated /etc.
- [ 13.663744@1] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.681595@1] systemd[1]: Set hostname to <OpenELEC>.
- [ 13.681697@1] systemd[1]: Initializing machine ID from random generator.
- [ 13.688170@1] systemd[1]: Populated /etc with preset unit settings.
- [ 13.696588@1] systemd[1]: Unit type .busname is not supported on this system.
- [ 13.721428@1] systemd[1]: Unit type .automount is not supported on this system.
- [ 13.733258@1] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
- [ 13.735392@1] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
- [ 13.743287@1] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
- [ 13.751241@1] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
- [ 13.759504@1] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.771510@0] systemd[1]: Reached target Paths.
- [ 13.771563@0] systemd[1]: Starting Paths.
- [ 13.774535@0] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.791494@1] systemd[1]: Created slice Root Slice.
- [ 13.791544@1] systemd[1]: Starting Root Slice.
- [ 13.795312@1] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.811488@1] systemd[1]: Listening on udev Control Socket.
- [ 13.811540@1] systemd[1]: Starting udev Control Socket.
- [ 13.816724@1] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.831498@1] systemd[1]: Listening on udev Kernel Socket.
- [ 13.831549@1] systemd[1]: Starting udev Kernel Socket.
- [ 13.836545@1] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.851509@2] systemd[1]: Listening on Delayed Shutdown Socket.
- [ 13.851809@2] systemd[1]: Starting Delayed Shutdown Socket.
- [ 13.857484@2] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.871489@2] systemd[1]: Listening on Journal Socket.
- [ 13.871551@2] systemd[1]: Starting Journal Socket.
- [ 13.875862@2] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.891489@2] systemd[1]: Listening on Journal Audit Socket.
- [ 13.891540@2] systemd[1]: Starting Journal Audit Socket.
- [ 13.896890@2] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.911488@2] systemd[1]: Listening on Journal Socket (/dev/log).
- [ 13.911958@2] systemd[1]: Starting Journal Socket (/dev/log).
- [ 13.917813@2] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.931500@2] systemd[1]: Created slice System Slice.
- [ 13.931561@2] systemd[1]: Starting System Slice.
- [ 13.936238@2] systemd[1]: Mounting Debug File System...
- [ 13.940835@2] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.952294@2] systemd[1]: Mounting Variable Directory...
- [ 13.952445@2] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.972218@2] systemd[1]: Mounting Temporary Directory...
- [ 13.972350@2] config uart_ao_ttyS0:: Character length 8bits/char
- [ 13.991724@2] systemd[1]: Started Debug Shell.
- [ 13.992540@2] systemd[1]: Starting Mounting swapfile...
- [ 13.995844@2] config uart_ao_ttyS0:: Character length 8bits/char
- [ 14.012225@2] systemd[1]: Mounting POSIX Message Queue File System...
- [ 14.013129@2] config uart_ao_ttyS0:: Character length 8bits/char
- [ 14.032460@3] config uart_ao_ttyS0:: Character length 8bits/char
- [ 14.051504@2] systemd[1]: Started Debug Shell on /dev/ttyS0.
- [ 14.051519@3] config uart_ao_ttyS0:: Character length 8bits/char
- [ 14.051622@2] systemd[1]: Starting Debug Shell on /dev/ttyS0...
- [ 14.056901@2] systemd[1]: Starting udev Coldplug all Devices...
- [ 14.063133@2] systemd[1]: Starting Remount Root and Kernel File Systems...
- [ 14.071550@2] systemd[1]: Starting Load Kernel Modules...
- [ 14.075395@2] systemd[1]: Starting Show Version...
- [ 14.080709@2] systemd[1]: Starting Create list of required static device nodes for the current kernel...
- [ 14.089924@2] systemd[1]: Starting Setup machine-id...
- [ 14.090479@0] gpu cooling register okay with err=0
- [ 14.090610@0] gpu core cooling register okay with err=0
- [ 14.090770@0] Mali: Mali device driver loaded
- [ 14.096295@0] buf[0]=ee,buf[1]=af,err=4
- [ 14.096303@0] M8M2:adc=383,TS_C=14,flag=1
- [ 14.096304@0] efuse_flag=a
- [ 14.096307@0] amlogic_thermal_probe, this chip is trimmed, use thermal
- [ 14.096312@0] amlogic-thermal aml_thermal: amlogic thermal probe start
- [ 14.096314@0] #thermal-cells=7
- [ 14.096316@0] keep_mode is disabled
- [ 14.096318@0] pdata->temp_trip_count=4
- [ 14.096321@0] temperature=70 on trip point=0
- [ 14.096325@0] fixing high_freq=1608001 to 1608000 at trip point 0,level=2
- [ 14.096328@0] fixing low_freq=1608001 to 1608000 at trip point 0,level=2
- [ 14.096330@0] gpu[0].gpu_high_freq=511,tmp_level[0].gpu_high_freq=511
- [ 14.096331@0] cpu[0] core num==3
- [ 14.096332@0] gpu[0] core num==5
- [ 14.096334@0] temperature=80 on trip point=1
- [ 14.096336@0] fixing high_freq=1200001 to 1200000 at trip point 1,level=6
- [ 14.096339@0] fixing low_freq=1200001 to 1200000 at trip point 1,level=6
- [ 14.096341@0] gpu[1].gpu_high_freq=435,tmp_level[1].gpu_high_freq=435
- [ 14.096342@0] cpu[1] core num==2
- [ 14.096343@0] gpu[1] core num==4
- [ 14.096344@0] temperature=90 on trip point=2
- [ 14.096347@0] fixing high_freq=800001 to 696000 at trip point 2,level=11
- [ 14.096350@0] fixing low_freq=800001 to 696000 at trip point 2,level=11
- [ 14.096352@0] gpu[2].gpu_high_freq=328,tmp_level[2].gpu_high_freq=328
- [ 14.096353@0] cpu[2] core num==2
- [ 14.096354@0] gpu[2] core num==3
- [ 14.096355@0] temperature=260 on trip point=3
- [ 14.096358@0] fixing high_freq=-1 to -22 at trip point 3,level=-1
- [ 14.096361@0] fixing low_freq=-1 to -22 at trip point 3,level=-1
- [ 14.096362@0] gpu[3].gpu_high_freq=-1,tmp_level[3].gpu_high_freq=-1
- [ 14.096363@0] cpu[3] core num==-1
- [ 14.096365@0] gpu[3] core num==-1
- [ 14.096366@0] idle interval=1000
- [ 14.096368@0] pdata->name:aml_thermal, pdata:ed728a00
- [ 14.096370@0] amlogic_thermal_init_from_dts, 998
- [ 14.096371@0] amlogic_thermal_initialize, 1014, pdata:ed728a00
- [ 14.096724@0] tmp_trip[0].cpu_core_upper=1
- [ 14.096732@0] tmp_trip[1].cpu_core_upper=2
- [ 14.096737@0] tmp_trip[2].cpu_core_upper=2
- [ 14.096742@0] tmp_trip[3].cpu_core_upper=-1
- [ 14.096747@0] aml_thermal bind thermal-cpucore-0 okay !
- [ 14.096771@0] aml_thermal bind thermal-cpufreq-0 okay !
- [ 14.096773@0] tmp_trip[0].gpu_core_upper=1
- [ 14.096780@0] tmp_trip[1].gpu_core_upper=2
- [ 14.096785@0] tmp_trip[2].gpu_core_upper=3
- [ 14.096791@0] tmp_trip[3].gpu_core_upper=-1
- [ 14.096796@0] aml_thermal bind thermal-gpucore-0 okay !
- [ 14.096799@0] pdata->tmp_trip[0].gpu_lower_level=1
- [ 14.096801@0] pdata->tmp_trip[0].gpu_upper_level=1
- [ 14.096806@0] pdata->tmp_trip[1].gpu_lower_level=2
- [ 14.096808@0] pdata->tmp_trip[1].gpu_upper_level=2
- [ 14.096814@0] pdata->tmp_trip[2].gpu_lower_level=3
- [ 14.096815@0] pdata->tmp_trip[2].gpu_upper_level=3
- [ 14.096828@0] pdata->tmp_trip[3].gpu_lower_level=-1
- [ 14.096829@0] pdata->tmp_trip[3].gpu_upper_level=-1
- [ 14.096835@0] aml_thermal bind thermal-gpufreq-0 okay !
- [ 14.096963@0] amlogic: Kernel Thermal management registered
- [ 14.096967@0] amlogic-thermal aml_thermal: amlogic thermal probe done
- [ 14.097759@0] Triggered SDIO WiFi power on and bus rescan.
- [ 14.097760@0] wifi_setup_dt
- [ 14.097763@0] wifi_request_32k_clk : ON-->ON for sdio_wifi
- [ 14.097765@0] interrupt_pin(133) : (null)
- [ 14.097778@0] reg:2620,clearmask=100010,setmask=0
- [ 14.097781@0] reg:2622,clearmask=ff,set pin=133
- [ 14.097783@0] reg:2623,clearmask=70000,setmask=4
- [ 14.097784@0] interrupt_pin(133) : sdio_wifi
- [ 14.097786@0] power_on_pin(6) : (null)
- [ 14.097791@0] power_on_pin(6) : sdio_wifi
- [ 14.097792@0] power_on_pin2(123) : (null)
- [ 14.097798@0] power_on_pin2(123) : sdio_wifi
- [ 14.401460@0] WIFI Disable! 6
- [ 14.439999@2] systemd[1]: Mounted Huge Pages File System.
- [ 14.445367@2] systemd[1]: Created slice User and Session Slice.
- [ 14.451239@2] systemd[1]: Starting User and Session Slice.
- [ 14.456754@2] systemd[1]: Reached target Slices.
- [ 14.461290@2] systemd[1]: Starting Slices.
- [ 14.465556@2] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
- [ 14.472666@2] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
- [ 14.480388@2] systemd[1]: Mounted Debug File System.
- [ 14.485415@2] systemd[1]: Mounted POSIX Message Queue File System.
- [ 14.491619@2] systemd[1]: Mounted Variable Directory.
- [ 14.496626@2] systemd[1]: Mounted Temporary Directory.
- [ 14.505729@2] systemd[1]: Started Remount Root and Kernel File Systems.
- [ 14.512986@2] systemd[1]: Started Show Version.
- [ 14.518031@2] systemd[1]: Started Create list of required static device nodes for the current kernel.
- [ 14.527728@2] systemd[1]: Started Setup machine-id.
- [ 14.533115@2] systemd[1]: Started Mounting swapfile.
- [ 14.558385@2] systemd[1]: Started udev Coldplug all Devices.
- [ 14.618765@2] systemd[1]: Reached target Swap.
- [ 14.623153@2] systemd[1]: Starting Swap.
- [ 14.627747@2] systemd[1]: Starting Journal Service...
- [ 14.633169@2] systemd[1]: Starting Create Static Device Nodes in /dev...
- [ 14.640729@2] systemd[1]: Started Rebuild Hardware Database.
- [ 14.646889@2] systemd[1]: Starting Setup Timezone data...
- [ 14.650130@2] systemd[1]: Started Debug /var/log relink.
- [ 14.656179@2] systemd[1]: Started Create Static Device Nodes in /dev.
- [ 14.669327@2] systemd[1]: Started Setup Timezone data.
- [ 14.694523@2] systemd[1]: Reached target Local File Systems (Pre).
- [ 14.700644@2] systemd[1]: Starting Local File Systems (Pre).
- [ 14.706350@2] systemd[1]: Reached target Local File Systems.
- [ 14.711465@0] WIFI Enable! 6
- [ 14.715089@2] systemd[1]: Starting Local File Systems.
- [ 14.720059@2] systemd[1]: Started Rebuild Journal Catalog.
- [ 14.725773@2] systemd[1]: Started Journal Service.
- [ 14.744830@0] systemd-journald[2455]: Received request to flush runtime journal from PID 1
- [ 15.711465@0] [aml_sdio_timeout] time_start_cnt:999
- [ 15.711465@0] [aml_sdio_print_err] sdio: Timeout error, Cmd52 arg 0xc00, Xfer 0 Bytes, host->xfer_step=12, host->cmd_is_stop=0, pdata->port=0, virqs=0x113, virqc=0x1f001f00, conf->cmd_clk_divide=177, pdata->clkc=177, conf->bus_width=0, pdata->width=0, conf=0x416270b1, clock=397940
- [ 15.711465@0] [aml_sdio_timeout] time_start_cnt:994
- [ 15.711465@0] [aml_sdio_print_err] sdio: Timeout error, Cmd52 arg 0x80000c08, Xfer 0 Bytes, host->xfer_step=12, host->cmd_is_stop=0, pdata->port=0, virqs=0x13, virqc=0x3f003f00, conf->cmd_clk_divide=177, pdata->clkc=177, conf->bus_width=0, pdata->width=0, conf=0x416270b1, clock=397940
- [ 15.711465@0]
- [ 17.751454@0] [aml_sdio_timeout] time_start_cnt:992
- [ 17.751454@0] <4>[ 17.786064@0] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
- [ 17.787405@0] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
- [ 17.793051@0] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
- [ 17.799705@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
- [ 17.841561@0] sdio: new high speed SDIO card at address 0001, clock 35416666, 4-bit-bus-width
- [ 17.845123@0] [sdio_reinit] finish
- [ 17.753553@3] [aml_sdio_print_err] sdio: Timeout error, Cmd8 arg 0x1aa, Xfer 0 Bytes, host->xfer_step=12, host->cmd_is_stop=0, pdata->port=0, virqs=0x13, virqc=0x1f003f00, conf->cmd_clk_divide=177, pdata->clkc=177, conf->bus_width=0, pdata->width=0, conf=0x416270b1, clock=397940
- [ 17.753553@3]
- [ 18.296809@3] Console: switching to colour dummy device 80x30
- [ 18.377432@1] cur_mode = 0
- [ 18.380162@1] [0x0] = 0x1dd0190
- [ 18.383528@1] [0x4] = 0xf800ca
- [ 18.385969@1] [0x8] = 0x82006e
- [ 18.389195@1] [0xc] = 0x3c0030
- [ 18.393906@1] [0x10] = 0x30fa0013
- [ 18.395921@1] [0x18] = 0x6f19000
- [ 18.398764@1] [0x1c] = 0x9f40
- [ 18.401768@1] [0x20] = 0x0
- [ 18.404174@1] [0x24] = 0x0
- [ 18.407180@1] [0x28] = 0x0
- [ 18.409543@1] set_remote_mode[69]
- [ 18.550595@3] type=1325 audit(72729785.660:2): table=filter family=2 entries=4
- [ 18.600291@0] type=1325 audit(72729785.710:3): table=mangle family=2 entries=6
- [ 18.625207@3] type=1325 audit(72729785.740:4): table=nat family=2 entries=5
- [ 18.633808@0] The PHY does not support set_wol, was CONFIG_MICREL_PHY enabled?
- [ 18.733862@0] type=1325 audit(72729785.850:5): table=mangle family=2 entries=6
- [ 18.769605@2] type=1325 audit(72729785.010:6): table=mangle family=2 entries=10
- [ 18.778993@2] netdev_open
- [ 18.779017@2] Ethernet reset
- [ 18.779039@2] NET MDA descpter start addr=ec78a000
- [ 18.785339@2] phy_interface = 1
- [ 18.786964@2] aml_phy_init: trying to attach to 0:00
- [ 18.795818@2] --1--write mac add to:ecf636c8: 16 84 bc 9f 78 a3 |...x.|
- [ 18.802948@2] name=emmc_key nand_key
- [ 18.805103@2] device name=nand_key open error
- [ 18.811983@2] aml_keys: version 0 can not be init c0c0259c
- [ 18.819952@2] ret = -22
- [ 18.819952@2] print_buff=
- [ 18.833056@2] yxg----flash mac addr
- [ 18.836896@2] yxg----keys_version is 0
- [ 18.840965@2] --2--write mac add to:ecf636c8: 9a a5 37 ac 23 03 |..7.#.|
- [ 18.845068@2] write mac add to:ecf636c8: 9a a5 37 ac 23 03 |..7.#.|
- [ 18.857158@2] Current DMA mode=0, set mode=621c100
- [ 18.861912@2] eth0: opened (irq 40).
- [ 18.861924@2] ether leave promiscuous mode
- [ 18.865704@2] ether leave all muticast mode
- [ 18.869860@2] changed the Multicast,mcount=1
- [ 18.874134@2] add mac address:33:33:00:00:00:01,bit=1
- [ 18.879136@2] set hash low=2,high=0
- [ 18.882627@2] changed the filter setting to :4
- [ 18.894694@2] changed the Multicast,mcount=1
- [ 18.896826@2] add mac address:33:33:00:00:00:01,bit=1
- [ 18.902518@2] changed the Multicast,mcount=2
- [ 18.906097@2] add mac address:33:33:00:00:00:01,bit=1
- [ 18.911125@2] add mac address:01:00:5e:00:00:01,bit=32
- [ 18.914479@1] as an end receiver
- [ 18.915563@3] ionvideo open
- [ 18.915667@3] ionvideo_stop_generating!!!!
- [ 18.915678@3] ionvideo release
- [ 18.929353@2] set hash low=2,high=1
- [ 18.932815@2] changed the filter setting to :4
- [ 18.936597@3] dhd_module_init: Enter
- [ 18.936599@3] wifi_setup_dt
- [ 18.936601@3] wifi_request_32k_clk : ON-->ON for sdio_wifi
- [ 18.936604@3] interrupt_pin(133) : sdio_wifi
- [ 18.936608@3] sdio_wifi is using the pin GPIOX_21
- [ 18.936610@3] wifi_dt : gpio op failed(-16) at line 210
- [ 18.936617@3] reg:2620,clearmask=100010,setmask=0
- [ 18.936620@3] reg:2622,clearmask=ff,set pin=133
- [ 18.936621@3] reg:2623,clearmask=70000,setmask=4
- [ 18.936623@3] interrupt_pin(133) : sdio_wifi
- [ 18.936625@3] power_on_pin(6) : sdio_wifi
- [ 18.936626@3] sdio_wifi is using the pin GPIOAO_6
- [ 18.936628@3] wifi_dt : gpio op failed(-16) at line 232
- [ 18.936630@3] power_on_pin(6) : sdio_wifi
- [ 18.936632@3] power_on_pin2(123) : sdio_wifi
- [ 18.936633@3] sdio_wifi is using the pin GPIOX_11
- [ 18.936635@3] wifi_dt : gpio op failed(-16) at line 244
- [ 18.936636@3] power_on_pin2(123) : sdio_wifi
- [ 18.936658@3] WIFI Disable! 6
- [ 19.020566@2] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- [ 19.138136@3] WIFI Enable! 6
- [ 19.338151@3] sdio_reset_comm():
- [ 19.352751@0] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
- [ 19.354596@0] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
- [ 19.360520@0] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
- [ 19.367644@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
- [ 19.420507@0] [sdio_reinit] finish
- [ 19.420738@0] =========== WLAN placed in POWER ON ========
- [ 19.424270@0] bcmsdh_register: Linux Kernel SDIO/MMC Driver
- [ 19.429466@0] dhd_customer_oob_irq_map: customer specific Host GPIO number is (100)
- [ 19.439906@0] F1 signature OK, socitype:0x1 chip:0x4330 rev:0x4 pkg:0x0
- [ 19.441475@1] hdmitx: cec: CEC node init
- [ 19.441479@1] hdmitx: cec: cec_func_config: 0xf; P_AO_DEBUG_REG0:0xf
- [ 19.441482@1] hdmitx: cec: enable:int mask:0x6
- [ 19.442356@1] hdmitx: cec: CEC: start poll dev
- [ 19.463463@0] DHD: dongle ram size is set to 294912(orig 294912) at 0x0
- [ 19.469429@0] dhdsdio_probe: Disable prop_txstatus
- [ 19.474537@0] wl_create_event_handler(): thread:wl_event_handler:af0 started
- [ 19.480952@0] init wlan_priv_wake
- [ 19.484323@0] tsk Enter, tsk = 0xf06b04cc
- [ 19.488525@0] dhd_attach(): thread:dhd_watchdog_thread:af4 started
- [ 19.494551@0] dhd_attach(): thread:dhd_dpc:af6 started
- [ 19.499736@0] dhd_attach(): thread:dhd_sysioc:af8 started
- [ 19.512112@0] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33
- [ 19.515001@0] =========== WLAN placed in RESET ========
- [ 19.520117@0] init wifi power_wake lock
- [ 19.521072@2] dhd_open: Enter ed610000
- [ 19.521077@2]
- [ 19.521077@2] Dongle Host Driver, version 1.88.45.4 (r420671)
- [ 19.521077@2] Compiled in drivers/net/wireless/bcmdhd on Aug 3 2015 at 14:55:15
- [ 19.521079@2] wl_android_wifi_on in 1
- [ 19.521081@2] wl_android_wifi_on in 2: g_wifi_on=0
- [ 19.521088@2] WIFI Disable! 6
- [ 19.554130@0]
- [ 19.554130@0] Dongle Host Driver, version 1.88.45.4 (r420671)
- [ 19.554130@0] Compiled in drivers/net/wireless/bcmdhd on Aug 3 2015 at 14:55:15
- [ 19.568669@0] dhd_module_init: Exit error=0
- [ 19.726807@2] WIFI Enable! 6
- [ 19.841894@0] enter:aml_m8_codec_mute_stream, mute=1, stream=0
- [ 19.841903@0] aml_i2s_close device type 8
- [ 19.858679@0] IEC958 16bit
- [ 19.858706@0] hdmitx: audio: aout notify rate 48000
- [ 19.860607@0] hdmitx: audio: aout notify size 16
- [ 19.865240@0] hdmitx: audio: audio channel num is 1
- [ 19.870063@0] hdmitx: audio: SPDIF
- [ 19.873538@0] hdmitx: audio: current VIC: 4
- [ 19.877613@0] hdmitx: audio: audio sample rate: 3
- [ 19.882303@0] hdmitx: audio: set audio N para
- [ 19.886619@0] hdmitx: audio: PCM out to HDMI
- [ 19.890870@0] hdmitx: audio: i2s_to_spdif_flag:1
- [ 19.895559@0] hdmitx: audio: Enable audio spdif to HDMI
- [ 19.900745@0] hdmitx: audio: Audio Type: PCM
- [ 19.905053@0] hdmitx: audio: set audio param
- [ 19.909252@0] aml_i2s_close device type 2
- [ 19.914848@0] IEC958 16bit
- [ 19.915999@0] hdmitx: audio: aout notify rate 48000
- [ 19.920851@0] hdmitx: audio: aout notify size 16
- [ 19.925705@0] hdmitx: audio: audio channel num is 1
- [ 19.926631@2] sdio_reset_comm():
- [ 19.933564@0] hdmitx: audio: SPDIF
- [ 19.936908@0] hdmitx: audio: current VIC: 4
- [ 19.941066@0] hdmitx: audio: audio sample rate: 3
- [ 19.945754@0] hdmitx: audio: set audio N para
- [ 19.950083@0] hdmitx: audio: PCM out to HDMI
- [ 19.954334@0] hdmitx: audio: i2s_to_spdif_flag:1
- [ 19.959010@0] hdmitx: audio: Enable audio spdif to HDMI
- [ 19.964217@0] hdmitx: audio: Audio Type: PCM
- [ 19.968488@0] hdmitx: audio: set audio param
- [ 19.972721@0] aml_i2s_close device type 2
- [ 19.984338@0] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
- [ 19.986099@0] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
- [ 20.043303@0] [sdio_reinit] finish
- [ 20.074754@3] IEC958_mode_codec= 0,IEC958 type 2 CH PCM
- [ 20.074792@3] last mode 0,now 0
- [ 20.083074@3] ----aml_hw_iec958_init,runtime->rate=44100--
- [ 20.083121@3] [aml-spdif-dai]enterd aml_hw_iec958_init,set_clock:4,sample_rate=5
- [ 20.083360@2] hdmitx: cec: hw reset :logical addr:0x14
- [ 20.083363@2] hdmitx: cec: CEC: poll online logic device: 0x4 BOOL: 0
- [ 20.083364@2] hdmitx: cec: player_dev[0]:0x4
- [ 20.083366@2] hdmitx: cec: physical address:0x1000
- [ 20.083480@2] hdmitx: cec: Set logical address: 4
- [ 20.116207@3] audio_set_958_clk, freq=5,
- [ 20.119619@3] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
- [ 20.126413@3] iec958 mode PCM16
- [ 20.129406@3] IEC958 16bit
- [ 20.132207@3] hdmitx: audio: aout notify rate 44100
- [ 20.136945@3] hdmitx: audio: aout notify size 16
- [ 20.141653@3] hdmitx: audio: audio channel num is 1
- [ 20.146396@3] hdmitx: audio: SPDIF
- [ 20.149775@3] hdmitx: audio: current VIC: 4
- [ 20.150396@1] =========== WLAN going back to live ========
- [ 20.150710@0]
- [ 20.150710@0]
- [ 20.150710@0] dhd_bus_devreset: == WLAN ON ==
- [ 20.150712@0] dhd_bus_devreset called when dongle is not in reset
- [ 20.150713@0] Will call dhd_bus_start instead
- [ 20.150761@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm40183b2.bin
- [ 20.150771@0] dhd_conf_set_nv_name_by_chip: nvram_path=/lib/firmware/brcm/ap6330_nvram.txt
- [ 20.150948@0] dhd_conf_read_config: Ignore config file /etc/wifi/config.txt
- [ 20.150951@0] Final fw_path=/lib/firmware/brcm/fw_bcm40183b2.bin
- [ 20.150952@0] Final nv_path=/lib/firmware/brcm/ap6330_nvram.txt
- [ 20.150954@0] Final conf_path=/etc/wifi/config.txt
- [ 20.218015@3] hdmitx: audio: audio sample rate: 2
- [ 20.222623@3] hdmitx: audio: set audio N para
- [ 20.227314@3] hdmitx: audio: PCM out to HDMI
- [ 20.231172@3] hdmitx: audio: i2s_to_spdif_flag:1
- [ 20.235853@3] hdmitx: audio: Enable audio spdif to HDMI
- [ 20.241049@3] hdmitx: audio: Audio Type: PCM
- [ 20.245341@3] hdmitx: audio: set audio param
- [ 20.249800@3] [aml-spdif-dai]spdif dma ef400000,phy addr 2f600000
- [ 20.255679@3] enter aml_set_bias_level level: 1
- [ 20.255685@3] enter aml_set_bias_level level: 2
- [ 20.255933@3] ----aml_hw_iec958_init,runtime->rate=44100--
- [ 20.261078@3] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
- [ 20.268068@3] iec958 mode PCM16
- [ 18.913071@0] amlvideo openamlvideo close
- [ 20.268883@0] NVRAM version: AP6330_NVRAM_V1.0_20121130
- [ 20.269432@0] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
- [ 20.283720@3] IEC958 16bit
- [ 20.286557@3] hdmitx: audio: aout notify rate 44100
- [ 20.291407@3] hdmitx: audio: aout notify size 16
- [ 20.296010@3] hdmitx: audio: audio channel num is 1
- [ 20.300862@3] hdmitx: audio: SPDIF
- [ 20.304252@3] hdmitx: audio: current VIC: 4
- [ 20.308399@3] hdmitx: audio: audio sample rate: 2
- [ 20.313082@3] hdmitx: audio: set audio N para
- [ 20.317416@3] hdmitx: audio: PCM out to HDMI
- [ 20.321667@3] hdmitx: audio: i2s_to_spdif_flag:1
- [ 20.326342@3] hdmitx: audio: Enable audio spdif to HDMI
- [ 20.331556@3] hdmitx: audio: Audio Type: PCM
- [ 20.335831@3] hdmitx: audio: set audio param
- [ 20.340036@3] [aml-spdif-dai]spdif dma ef400000,phy addr 2f600000
- [ 20.346152@3] enter aml_set_bias_level level: 1
- [ 20.346156@3] enter aml_set_bias_level level: 2
- [ 20.352404@3] [aml-spdif-dai]aiu 958 playback enable
- [ 20.539546@0] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
- [ 20.586934@0] bcmsdh_set_drvdata: Enter
- [ 20.586962@0] bcmsdh_register_oob_intr: Enter
- [ 20.589556@0] bcmsdh_register_oob_intr: IRQ=100 Type=414
- [ 20.603326@0] dhd_conf_set_band: Set band 0
- [ 20.611749@1] Firmware up: op_mode=0x0005, Broadcom Dongle Host Driver mac=04:e6:76:28:60:dd
- [ 20.614543@1] dhd_conf_set_country: Set country ALL, revision 0
- [ 20.693258@1] Country code: ALL (ALL/0)
- [ 20.693600@1] dhd_conf_set_roam: Set roam_off 1
- [ 20.697861@1] dhdcdc_set_ioctl: msg->status:ffffffe9
- [ 20.707006@1] Driver: 1.88.45.4 (r420671)
- [ 20.707006@1] Firmware: wl0: Jan 6 2014 15:11:29 version 5.90.195.89.13 FWID 01-72f124c5
- [ 20.714431@1] wl_android_wifi_on: Success
- [ 20.733987@1] dhd_open: Exit ret=0
- [ 20.837534@0] tvmode set to 1080p
- [ 20.837565@0] mode is 15,sync_duration_den=1,sync_duration_num=60
- [ 20.841395@0] TV mode 1080p selected.
- [ 20.845038@0] tvoutc_setmode[489]
- [ 20.848308@0] new mode 1080p set ok
- [ 20.851892@0] hdmitx: video: get current mode: 1080p
- [ 20.856712@0] is_similar_hdmi_vic[324] vic_old=4,mode_new=15
- [ 20.862368@0] hdmitx: video: get current mode: 1080p
- [ 20.867296@0] is_similar_hdmi_vic[324] vic_old=4,mode_new=15
- [ 20.872942@0] hdmitx: system: gate/pwr cmd: 7
- [ 20.877328@0] hdmitx: system: already init VIC = 0 Now VIC = 16
- [ 20.883272@0] hdmitx: system: 16 (cd0,cs0,pm1,vd0,1)
- [ 20.888362@0] hdmitx: system: gate/pwr cmd: 0
- [ 20.892713@0] hdmitx: system: hw reset
- [ 20.897464@0] hdmitx: audio: SPDIF
- [ 20.899844@0] hdmitx: system: reconfig packet setting done
- [ 21.041450@2] hdmitx: system: phy setting done
- [ 21.061469@2] hdmitx: system: set pll
- [ 21.061489@2] hdmitx: system: param->VIC:16
- [ 21.063652@2] mode is: 15
- [ 21.066251@2] VPU_VIU_VENC_MUX_CTRL: 0x22a
- [ 21.070324@2] viu chan = 1
- [ 21.073034@2] VPU_VIU_VENC_MUX_CTRL: 0x22a
- [ 21.077086@2] config HPLL
- [ 21.079687@2] set_hpll_clk_out[62] clk = 2970
- [ 21.101452@2] config HPLL done
- [ 21.101476@2] enc_vpu_bridge_reset[292]
- [ 21.241454@2] hdmitx: system: phy setting done
- [ 21.241479@2] Sink is HDMI device
- [ 21.243552@2] No sink attached
- [ 21.246618@2] hdmitx: audio: audio channel num is 1
- [ 21.251732@2] hdmitx: audio: SPDIF
- [ 21.254826@2] hdmitx: audio: current VIC: 16
- [ 21.259065@2] hdmitx: audio: audio sample rate: 2
- [ 21.263937@2] hdmitx: audio: set audio N para
- [ 21.268085@2] hdmitx: audio: PCM out to HDMI
- [ 21.272351@1] hdmitx: audio: i2s_to_spdif_flag:1
- [ 21.277009@1] hdmitx: audio: Enable audio spdif to HDMI
- [ 21.282223@1] hdmitx: audio: Audio Type: PCM
- [ 21.287045@1] set_vout_mode[249]
- [ 22.791648@2] libphy: 0:00 - Link is Up - 100/Full
- [ 22.791736@2] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- [ 22.798585@2] changed the Multicast,mcount=3
- [ 22.801499@2] add mac address:33:33:00:00:00:01,bit=1
- [ 22.806505@2] add mac address:01:00:5e:00:00:01,bit=32
- [ 22.811637@2] add mac address:33:33:ff:ac:23:03,bit=6
- [ 22.816646@2] set hash low=42,high=1
- [ 22.820199@2] changed the filter setting to :4
- [ 24.321472@0] hdmitx: cec: cec node init: cec features ok !
- [ 24.851499@0] enter aml_set_bias_level level: 1
- [ 24.851510@0] enter aml_set_bias_level level: 2
- [ 25.774144@2] changed the Multicast,mcount=2
- [ 25.774180@2] add mac address:33:33:00:00:00:01,bit=1
- [ 25.777812@2] add mac address:01:00:5e:00:00:01,bit=32
- [ 25.782948@2] set hash low=2,high=1
- [ 25.786391@2] changed the filter setting to :4
- [ 25.790980@2] changed the Multicast,mcount=1
- [ 25.790985@2] add mac address:01:00:5e:00:00:01,bit=32
- [ 25.790987@2] set hash low=0,high=1
- [ 25.790989@2] changed the filter setting to :4
- [ 28.770322@0] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
- [ 89.547600@0] [aml-spdif-dai]aiu 958 playback disable
- [ 89.547647@0] ----aml_hw_iec958_init,runtime->rate=44100--
- [ 89.552580@0] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
- [ 89.559259@0] iec958 mode PCM16
- [ 89.562383@0] IEC958 16bit
- [ 89.565047@0] hdmitx: audio: aout notify rate 44100
- [ 89.569896@0] hdmitx: audio: aout notify size 16
- [ 89.574519@0] hdmitx: audio: audio channel num is 1
- [ 89.579351@0] hdmitx: audio: SPDIF
- [ 89.582760@0] hdmitx: audio: current VIC: 16
- [ 89.586975@0] hdmitx: audio: audio sample rate: 2
- [ 89.591678@0] hdmitx: audio: set audio N para
- [ 89.595999@0] hdmitx: audio: PCM out to HDMI
- [ 89.600235@0] hdmitx: audio: i2s_to_spdif_flag:1
- [ 89.604947@0] hdmitx: audio: Enable audio spdif to HDMI
- [ 89.610123@0] hdmitx: audio: Audio Type: PCM
- [ 89.614424@0] hdmitx: audio: set audio param
- [ 89.618614@0] [aml-spdif-dai]spdif dma ef400000,phy addr 2f600000
- [ 89.624749@0] enter aml_set_bias_level level: 1
- [ 89.624755@0] enter aml_set_bias_level level: 2
- AMLOGIC:~ #
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement