[wip:20190130] OpenBSD-current on LicheePiZero Allwinner V3s

CUIсSPL 2019.01 (Jan 27 2019 - 18:58:44 +0900)
DRAM: 64 MiB
Trying to boot from MMC1


U-Boot 2019.01 (Jan 27 2019 - 18:58:44 +0900) Allwinner Technology

CPU:   Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM:  64 MiB
MMC:   SUNXI SD/MMC: 0
Loading Environment from FAT... *** Warning - bad CRC, using default environment

In:    serial@01c28000
Out:   serial@01c28000
Err:   serial@01c28000
Net:   No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
6610 bytes read in 3 ms (2.1 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
                                                                               ~Scanning disks on usb...
Disk usb0 not ready
Disk usb1 not ready
Disk usb2 not ready
Disk usb3 not ready
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 3 disks
89060 bytes read in 12 ms (7.1 MiB/s)
## Starting EFI application at 41000000 ...
>> OpenBSD/armv7 BOOTARM 1.1
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 4539280+683116+236608+561976 [299037+107+312768+276746]=0x6980e4

OpenBSD/armv7 booting ...
arg0 0xc09980e4 arg1 0x0 arg2 0x42d49000
Allocating page tables
IRQ stack: p0x409c7000 v0xc09c7000
ABT stack: p0x409c8000 v0xc09c8000
UND stack: p0x409c9000 v0xc09c9000
SVC stack: p0x409ca000 v0xc09ca000
Creating L1 page table at 0x4099c000
Mapping kernel
Constructing L2 page tables
undefined page type 0x2 pa 0x40000000 va 0x40000000 pages 0x2000 attr 0x8
type 0x7 pa 0x42000000 va 0x40000000 pages 0x5f8 attr 0x8
type 0x2 pa 0x425f8000 va 0x425f8000 pages 0x73b attr 0x8
type 0x1 pa 0x42d33000 va 0x42d33000 pages 0x16 attr 0x8
type 0x6 pa 0x42d49000 va 0x42d49000 pages 0xa attr 0x8000000000000008
type 0x0 pa 0x42d53000 va 0x42d51000 pages 0x2 attr 0x8
type 0x6 pa 0x42d55000 va 0x42d55000 pages 0x1 attr 0x8000000000000008
type 0x0 pa 0x42d56000 va 0x42d51000 pages 0x1 attr 0x8
type 0x6 pa 0x42d57000 va 0x42d57000 pages 0x1 attr 0x8000000000000008
type 0x0 pa 0x42d58000 va 0x42d58000 pages 0x2 attr 0x8
type 0x2 pa 0x42d5a000 va 0x42d5a000 pages 0x1223 attr 0x8
type 0x5 pa 0x43f7d000 va 0x43f7d000 pages 0x1 attr 0x8000000000000008
type 0x2 pa 0x43f7e000 va 0x42d5a000 pages 0x82 attr 0x8
pmap [ using 889196 bytes of bsd ELF symbol table ]
board type: 0
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2019 OpenBSD. All rights reserved.  https://www.OpenBSD.org

OpenBSD 6.4-current (GENERIC) #1: Wed Jan 30 06:45:11 JST 2019
    [email protected]:/usr/src/sys/arch/armv7/compile/GENERIC
real mem  = 39813120 (37MB)
avail mem = 28852224 (27MB)
warning: no entropy supplied by boot loader
mainbus0 at root: Lichee Pi Zero
cpu0 at mainbus0: ARM Cortex-A7 r0p5 (ARMv7)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache
cortex0 at mainbus0
psci0 at mainbus0: PSCI 0.0
agtimer0 at mainbus0: tick rate 24000 KHz
simplebus0 at mainbus0: "soc"
ampintc0 at simplebus0 nirq 160, ncpu 1: "interrupt-controller"
sximmc0 at simplebus0
sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
"usb" at simplebus0 not configured
"phy" at simplebus0 not configured
"clock" at simplebus0 not configured
sxirtc0 at simplebus0
"pinctrl" at simplebus0 not configured
"timer" at simplebus0 not configured
sxidog0 at simplebus0
com0 at simplebus0: ns16550, no working fifo
com0: console
"interrupt-controller" at simplebus0 not configured
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
scsibus1 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: lookup sd0a:/bsd failed.
root device: