restzsdrt

Mill G Codes
G00 Rapid Positioning Motion (X , Y , Z , A , B )
G01 Linear Interpolation Motion (X , Y , Z , A , B , F )
G02 Circular Interpolation Motion CW (X , Y , Z , A , I , J , K , R , F )
G03 Circular Interpolation Motion CCW (X , Y , Z , A , I , J , K , R , F )
G04 Dwell (P) (P=Seconds″.” Milliseconds)
G09 Exact Stop, Non-Modal
G17* Circular Motion XY Plane Selection (G02 or G03)
G18 Circular Motion ZX Plane Selection (G02 or G03)
G19 Circular Motion YZ Plane Selection (G02 or G03)
G20 Inch Coordinate Positioning
G21 Metric Coordinate Positioning
G28 Machine Zero Return Thru Ref. Point (X , Y , Z , A , B )
G29 Move to Location Through G28 Ref. Point (X , Y , Z , A , B )
G40* Cutter Comp Cancel G41/G42/G141 (X , Y )
G41 2D Cutter Compensation, Left (X , Y , D )
G42 2D Cutter Compensation, Right (X , Y , D )
G43 Tool Length Compensation + (H , Z )
G49* Tool Length Compensation Cancel G43/G44/G43
G52 Work Offset Positioning Coordinate
G53 Machine Positioning Coordinate, Non-Modal (X , Y , Z , A , B )
G54* Work Offset Positioning Coordinate #1 (Setting 56)
G55 Work Offset Positioning Coordinate #2
G56 Work Offset Positioning Coordinate #3
G57 Work Offset Positioning Coordinate #4
G58 Work Offset Positioning Coordinate #5
G59 Work Offset Positioning Coordinate #6
C G & M Codes
Appendix C
C-2 Mastercam X2
G73 HS Peck Drilling Canned Cycle (X , Y , A , B , Z , I , J , K , Q , P , R , L , F )
G74 Reverse Tapping Canned Cycle (X , Y , A , B , Z , J , R , L , F )
G76 Fine Boring Canned Cycle (X , Y , A , B , Z , I , J , P , Q , R , L , F )
G77 Black Bore Canned Cycle (X , Y , A , B , Z , I , J , Q , R , L , F )
G80* Cancel Canned Cycle (Setting 56)
G81 Drill Canned Cycle (X , Y , A , B , Z , R , L , F )
G82 Spot Drill / Counterbore Canned Cycle (X , Y , A , B , Z , P , R , L , F )
G83 Peck Drill Deep Hole Canned Cycle (X , Y , A , B , Z , I , J , K , Q , P , R , L , F )
G84 Tapping Canned Cycle (X , Y , A , B , Z , J , R , L , F )
G85 Bore In ~ Bore Out Canned Cycle (X , Y , A , B , Z , R , L , F )
G86 Bore In ~ Stop ~ Rapid Out Canned Cycle (X , Y , A , B , Z , R , L , F )
G87 Bore In ~ Manual Retract Canned Cycle (X , Y , A , B , Z , R , L , F )
G88 Bore In ~ Dwell ~ Manual Retract Canned Cycle (X , Y , A , B , Z , P , R , L , F )
G89 Bore In ~ Dwell ~ Bore Out Canned Cycle (X , Y , A , B , Z , P , R , L , F )
G90* Absolute Positioning Command
G91 Incremental Positioning Command
G92 Global Work Coordinate System
G93 Inverse Time Feed Mode ON
G94 Inverse Time Feed OFF / Feed Per Minute ON
G98 Canned Cycle Initial Point Return
G99 Canned Cycle R Plane Return
G&M Codes
Mastercam Handbook Volume 1
C-3
Mill M Codes
M00 Program Stop
M01 Optional Program Stop
M02 Program End
M03 Spindle ON Clockwise ()
M04 Spindle ON Counterclockwise (S))
M05 Spindle Stop
M06 Tool Change (T)
M08 Coolant ON
M09 Coolant OFF
M30 Program End and Reset
M31 Chip Auger Forward
M33 Chip Auger Stop
M34 Coolant Spigot Position Down, Increment
M35 Coolant Spigot Position Up, Decrement
M36 Pallet Part Ready
M41 Spindle Low Gear Override
M42 Spindle High Gear Override
M50 Execute Pallet Change
M83 Auto Air Jet ON
M84 Auto Air Jet OFF
M88 Coolant Through Spindle ON
M97 Local Sub-Program Call (P , L )
M98 Sub-Program Call (P , L )
M99 Sub-Program / Routine Return of Loop (P)


Progr