Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- OMAP36XX ZOOM3 # tftpboot 0x80300000 uImage
- LAN9x18 (0x92210000) detected.
- Read mac address: 00:08:EE:03:2A:4A
- start Auto negotiation... (take ~2sec)
- Auto negotiation complete, 100BaseTX, full duplex
- TFTP from server 172.24.137.86; our IP address is 172.24.190.192; sending through gateway 172.24.188.1
- Filename 'uImage'.
- Load address: 0x80300000
- Loading: #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- ################################################
- done
- Bytes transferred = 3238396 (3169fc hex)
- OMAP36XX ZOOM3 # bootm 0x80300000
- ## Booting image at 80300000 ...
- Image Name: Linux-2.6.36-rc5-00010-g006f23e
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 3238332 Bytes = 3.1 MB
- Load Address: 80008000
- Entry Point: 80008000
- Verifying Checksum ... OK
- OK
- Starting kernel ...
- Uncompressing Linux... done, booting the kernel.
- [ 0.000000] Linux version 2.6.36-rc5-00010-g006f23e (manju@manju-desktop) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #9 Tue Sep 28 08:23:09 IST 0
- [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
- [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
- [ 0.000000] Machine: OMAP Zoom3 board
- [ 0.000000] Memory policy: ECC disabled, Data cache writeback
- [ 0.000000] OMAP3630 ES1.0 (l2cache iva sgx neon isp 192mhz_clk )
- [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
- [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/nfs rw nfsroot=172.24.137.86:/home/manju/fs/newbbox target,nolock,tcp,rsize=1024,wsize=p
- [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
- [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
- [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Memory: 128MB = 128MB total
- [ 0.000000] Memory: 116152k/116152k available, 14920k reserved, 0K highmem
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
- [ 0.000000] vmalloc : 0xc8800000 - 0xf8000000 ( 760 MB)
- [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
- [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
- [ 0.000000] .init : 0xc0008000 - 0xc0047000 ( 252 kB)
- [ 0.000000] .text : 0xc0047000 - 0xc05e9000 (5768 kB)
- [ 0.000000] .data : 0xc0612000 - 0xc07e2900 (1859 kB)
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] RCU-based detection of stalled CPUs is disabled.
- [ 0.000000] Verbose stalled-CPUs detection is disabled.
- [ 0.000000] NR_IRQS:402
- [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz
- [ 0.000000] (null): Could not get uart4_ick
- [ 0.000000] (null): Could not get uart4_fck
- [ 0.000000] Reprogramming SDRC clock to 400000000 Hz
- [ 0.000000] GPMC revision 5.0
- [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
- [ 0.000000] Total of 96 interrupts on 1 active controller
- [ 0.000000] Could not get gpios_ick
- [ 0.000000] Could not get gpios_fck
- [ 0.000000] OMAP GPIO hardware version 2.5
- [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
- [ 0.000000] Console: colour dummy device 80x30
- [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
- [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
- [ 0.000000] ... MAX_LOCK_DEPTH: 48
- [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
- [ 0.000000] ... CLASSHASH_SIZE: 4096
- [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
- [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
- [ 0.000000] ... CHAINHASH_SIZE: 16384
- [ 0.000000] memory used by lock dependency info: 3951 kB
- [ 0.000000] per task-struct memory footprint: 2304 bytes
- [ 0.000000] Calibrating delay loop... 597.64 BogoMIPS (lpj=2334720)
- [ 0.000000] pid_max: default: 32768 minimum: 301
- [ 0.000000] Security Framework initialized
- [ 0.000000] Mount-cache hash table entries: 512
- [ 0.000000] CPU: Testing write buffer coherency: ok
- [ 0.000000] regulator: core version 0.5
- [ 0.000000] NET: Registered protocol family 16
- [ 0.000793] OMAP DMA hardware revision 5.0
- [ 0.083709] bio: create slab <bio-0> at 0
- [ 0.092590] SCSI subsystem initialized
- [ 0.100524] usbcore: registered new interface driver usbfs
- [ 0.101745] usbcore: registered new interface driver hub
- [ 0.102508] usbcore: registered new device driver usb
- [ 0.105468] i2c_omap i2c_omap.1: bus 1 rev4.0 at 2400 kHz
- [ 0.116668] twl4030: PIH (irq 7) chaining IRQs 368..375
- [ 0.116821] twl4030: power (irq 373) chaining IRQs 376..383
- [ 0.118896] twl4030: gpio (irq 368) chaining IRQs 384..401
- [ 0.129547] regulator: VUSB1V5: 1500 mV normal standby
- [ 0.131744] regulator: VUSB1V8: 1800 mV normal standby
- [ 0.134216] regulator: VUSB3V1: 3100 mV normal standby
- [ 0.140960] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
- [ 0.146606] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
- [ 0.148895] regulator: VMMC2: 1850 mV normal standby
- [ 0.151489] regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby
- [ 0.152160] i2c_omap i2c_omap.2: bus 2 rev4.0 at 400 kHz
- [ 0.166290] i2c_omap i2c_omap.3: bus 3 rev4.0 at 400 kHz
- [ 0.172332] Advanced Linux Sound Architecture Driver Version 1.0.23.
- [ 0.175994] Bluetooth: Core ver 2.15
- [ 0.176635] NET: Registered protocol family 31
- [ 0.176666] Bluetooth: HCI device and connection manager initialized
- [ 0.176788] Bluetooth: HCI socket layer initialized
- [ 0.178894] cfg80211: Calling CRDA to update world regulatory domain
- [ 0.182617] Switching to clocksource 32k_counter
- [ 0.287567] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
- [ 0.294097] musb_hdrc musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
- [ 0.295349] NET: Registered protocol family 2
- [ 0.295959] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.297760] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
- [ 0.298126] TCP bind hash table entries: 4096 (order: 5, 163840 bytes)
- [ 0.301025] TCP: Hash tables configured (established 4096 bind 4096)
- [ 0.301116] TCP reno registered
- [ 0.301147] UDP hash table entries: 64 (order: 0, 6144 bytes)
- [ 0.301483] UDP-Lite hash table entries: 64 (order: 0, 6144 bytes)
- [ 0.302368] NET: Registered protocol family 1
- [ 0.303527] RPC: Registered udp transport module.
- [ 0.303558] RPC: Registered tcp transport module.
- [ 0.303558] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 0.309844] NetWinder Floating Point Emulator V0.97 (double precision)
- [ 0.479095] VFS: Disk quotas dquot_6.5.2
- [ 0.479217] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 0.482208] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
- [ 0.483367] msgmni has been set to 226
- [ 0.489105] io scheduler noop registered
- [ 0.489135] io scheduler deadline registered
- [ 0.489349] io scheduler cfq registered (default)
- [ 0.493988] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- [ 0.523956] serial8250.0: ttyS0 at MMIO 0x10000000 (irq = 262) is a ST16654
- [ 1.110473] console [ttyS0] enabled
- [ 1.152465] brd: module loaded
- [ 1.173736] loop: module loaded
- [ 1.185913] mtdoops: mtd device (mtddev=name/number) must be supplied
- [ 1.192993] omap2-nand driver initializing
- [ 1.197540] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron omap2-nand.0)
- [ 1.205291] NAND bus width 8 instead 16 bit
- [ 1.209533] No NAND device found.
- [ 1.213012] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron NAND 512MiB 1,8V 16-bit)
- [ 1.221740] Creating 7 MTD partitions on "omap2-nand.0":
- [ 1.227142] 0x000000000000-0x000000080000 : "X-Loader-NAND"
- [ 1.240875] 0x000000080000-0x0000001c0000 : "U-Boot-NAND"
- [ 1.252014] 0x0000001c0000-0x000000200000 : "Boot Env-NAND"
- [ 1.262939] 0x000000200000-0x000002000000 : "Kernel-NAND"
- [ 1.288452] 0x000002000000-0x00001c000000 : "system"
- [ 1.504943] 0x00001c000000-0x00001e000000 : "userdata"
- [ 1.531036] 0x00001e000000-0x000020000000 : "cache"
- [ 1.557525] OneNAND driver initializing
- [ 1.568634] smsc911x: Driver version 2008-10-21.
- [ 1.579864] smsc911x-mdio: probed
- [ 1.583984] eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=ffffffff:01, irq=-1)
- [ 1.592834] net eth0: MAC Address: 00:08:ee:03:2a:4a
- [ 1.599273] usbcore: registered new interface driver asix
- [ 1.605499] usbcore: registered new interface driver cdc_ether
- [ 1.611907] usbcore: registered new interface driver net1080
- [ 1.618316] usbcore: registered new interface driver cdc_subset
- [ 1.624938] usbcore: registered new interface driver zaurus
- [ 1.631439] usbcore: registered new interface driver usb8xxx
- [ 1.637237] libertas_sdio: Libertas SDIO driver
- [ 1.641754] libertas_sdio: Copyright Pierre Ossman
- [ 1.649597] usbcore: registered new interface driver cdc_wdm
- [ 1.655395] Initializing USB Mass Storage driver...
- [ 1.661010] usbcore: registered new interface driver usb-storage
- [ 1.667022] USB Mass Storage support registered.
- [ 1.673004] usbcore: registered new interface driver libusual
- [ 1.679534] usbcore: registered new interface driver usbtest
- [ 1.687255] mice: PS/2 mouse device common for all mice
- [ 1.695587] input: TWL4030 Keypad as /devices/platform/i2c_omap.1/i2c-1/1-004a/twl4030_keypad/input/input0
- [ 1.713836] input: twl4030_pwrbutton as /devices/platform/i2c_omap.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1
- [ 1.728088] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
- [ 1.736724] i2c /dev entries driver
- [ 1.745513] Driver for 1-wire Dallas network protocol.
- [ 1.755615] Bluetooth: HCI UART driver ver 2.2
- [ 1.760070] Bluetooth: HCI H4 protocol initialized
- [ 1.765319] Bluetooth: HCI BCSP protocol initialized
- [ 1.770355] Bluetooth: HCILL protocol initialized
- [ 1.775054] Bluetooth: Broadcom Blutonium firmware driver ver 1.2
- [ 1.782226] usbcore: registered new interface driver bcm203x
- [ 1.788055] Bluetooth: Digianswer Bluetooth USB driver ver 0.10
- [ 1.794708] usbcore: registered new interface driver bpa10x
- [ 1.817565] usbcore: registered new interface driver usbhid
- [ 1.823150] usbhid: USB HID core driver
- [ 1.830261] usbcore: registered new interface driver snd-usb-audio
- [ 1.838531] No device for DAI omap-mcbsp-dai-0
- [ 1.843170] No device for DAI omap-mcbsp-dai-1
- [ 1.847686] No device for DAI omap-mcbsp-dai-2
- [ 1.852142] No device for DAI omap-mcbsp-dai-3
- [ 1.856658] No device for DAI omap-mcbsp-dai-4
- [ 1.861083] ALSA device list:
- [ 1.864105] No soundcards found.
- [ 1.867523] oprofile: hardware counters not available
- [ 1.872619] oprofile: using timer interrupt.
- [ 1.877441] TCP cubic registered
- [ 1.880737] Initializing XFRM netlink socket
- [ 1.885162] NET: Registered protocol family 17
- [ 1.889984] NET: Registered protocol family 15
- [ 1.895233] Bluetooth: L2CAP ver 2.15
- [ 1.898895] Bluetooth: L2CAP socket layer initialized
- [ 1.904174] Bluetooth: SCO (Voice Link) ver 0.6
- [ 1.908691] Bluetooth: SCO socket layer initialized
- [ 1.914062] Bluetooth: RFCOMM TTY layer initialized
- [ 1.919128] Bluetooth: RFCOMM socket layer initialized
- [ 1.924285] Bluetooth: RFCOMM ver 1.11
- [ 1.928100] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- [ 1.933441] Bluetooth: BNEP filters: protocol multicast
- [ 1.938690] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- [ 1.946990] lib80211: common routines for IEEE802.11 drivers
- [ 1.952850] Registering the dns_resolver key type
- [ 1.958160] ThumbEE CPU extension supported.
- [ 1.973693] Power Management for TI OMAP3.
- [ 2.021331] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
- [ 2.043060] twl_rtc twl_rtc: setting system clock to 2000-03-03 21:24:44 UTC (952118684)
- [ 2.245727] mmc1: new high speed MMC card at address 0001
- [ 2.253387] mmcblk0: mmc1:0001 STM16G 14.8 GiB
- [ 2.265197] mmcblk0: p1
- [ 2.560516] net eth0: SMSC911x/921x identified at 0xc8884000, IRQ: 318
- [ 3.574218] Sending DHCP requests .., OK
- [ 5.964538] IP-Config: Got DHCP answer from 0.0.0.0, my address is 172.24.190.45
- [ 5.973541] IP-Config: Complete:
- [ 5.976623] device=eth0, addr=172.24.190.45, mask=255.255.252.0, gw=172.24.188.1,
- [ 5.984558] host=172.24.190.45, domain=india.ti.com, nis-domain=(none),
- [ 5.991668] bootserver=0.0.0.0, rootserver=172.24.137.86, rootpath=
- [ 6.002166] Looking up port of RPC 100003/2 on 172.24.137.86
- [ 6.013793] Looking up port of RPC 100005/1 on 172.24.137.86
- [ 6.055755] VFS: Mounted root (nfs filesystem) on device 0:13.
- [ 6.061950] Freeing init memory: 252K
- Mounting proc : OK
- Mounting sysfs : OK
- Mounting /dev : OK
- Creating local mdev devices
- umount: can't umount /mnt/mmc: Invalid argument
- ******************************************
- Starting System Init for 3430SDP-3430
- Release: OpnSrc
- ******************************************
- Saving kernel ring buffer : OK
- Mounting devpts : OK
- Setting up networking
- Configuring lo : OK
- Configuring eth0 : OK - 172.24.190.45
- Starting telnetd : OK
- Starting syslogd : OK
- Starting klogd : OK
- Mounting filesystems : mount: according to /proc/mounts, none is already mounted on /dev/pts
- mount: according to /proc/mounts, /proc is already mounted on /proc
- OK
- Please press Enter to activate this console.
- #
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement