Slic3r config

acceleration = 0
bed_size = 200,200
bed_temperature = 0
bridge_fan_speed = 100
bridge_flow_ratio = 2.0
bridge_speed = 25
brim_width = 0
complete_objects = 0
cooling = 1
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M140 S0	;Turn heated bed off\nM104 S0	;Turn nozzle heat off\nG91 ;Make coordinates relative\nG0 Z2 E-2 ;Move up 2mm and retract extuder 2mm\nG90 ;Use absolute coordinates again\nG01 X100 Y200 F15000 ;Go to dump area\nM84 ;Disable steppers so they dont get hot during idling...
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_axis = E
extrusion_multiplier = 0.955
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 120
filament_diameter = 2.8
fill_angle = 45
fill_density = 0.2
fill_pattern = rectilinear
first_layer_bed_temperature = 0
first_layer_extrusion_width = 0
first_layer_height = 0.15
first_layer_speed = 10
first_layer_temperature = 185
g0 = 0
gcode_arcs = 0
gcode_comments =
gcode_flavor = reprap
infill_acceleration = 50
infill_every_layers = 1
infill_extrusion_width = 0
infill_speed = 40
layer_gcode =
layer_height = 0.2
max_fan_speed = 100
min_fan_speed = 40
min_print_speed = 5
notes =
nozzle_diameter = 0.35
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 25
perimeter_speed = 40
perimeters = 2
perimeters_extrusion_width = 0
post_process =
print_center = 100,100
randomize_start = 1
retract_before_travel = 2
retract_length = 1
retract_lift = 0
retract_restart_extra = 0.0
retract_speed = 20
rotate = 90
scale = 1.0
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 10
small_perimeter_speed = 10
solid_fill_pattern = rectilinear
solid_infill_speed = 25
solid_layers = 2
start_gcode = M106 S0 ; Make sure fan is stopped\nM104 S0 ;Cancel the M104 set by Slic3r\nM140 S[first_layer_bed_temperature] ;Start heating the bed up\nG00 X-200 F10000\nG00 Y-200 F10000\nG00 Z-100 F10000\nG28 X Y; home x and y\nG28 Z; home z\nG0 Z3\nM84 ;Disable all steppers\nM84 S30 ;Set stepper timeout to 30 seconds\nM104 S100 ;Set hotend temp to something that wont melt the plastic\nM190 S[first_layer_bed_temperature] ;Set bed temperature and wait\nM109 S[temperature] ;Set hotend temperature and wait\nG91 ;Make coordinates relative\nG01 E5 F60 ;Extrude 5mm\nG92 E0 ;Reset extruder position\nG90 ;Use absolute coordinates again
support_material =
support_material_angle = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_threshold = 45
support_material_tool = 0
temperature = 185
threads = 2
top_solid_infill_speed = 25
travel_speed = 1500
use_relative_e_distances = 0
z_offset = 0.0