API tools faq
paste
DaLuppo

logs NIGGA

DaLuppo
Jan 26th, 2020
411
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 81.75 KB | None | 0 0
raw download clone embed print report
  1. [2020-01-26 12:26:38] [Output] : ★ Marcus Wilburn lines the BMW with the entrance of the garage before stepping out and sliding his
  2. [2020-01-26 12:26:50] [Output] : ★ fingers beneath the garage door, raising it up to make clearance. ((Marcus Wilburn))
  3. [2020-01-26 12:27:18] [Output] : ★ Marcus Wilburn hops back inside the bimmer and slowly drives her inside the garage.
  4. [2020-01-26 12:28:30] [Output] : ★ Marcus Wilburn parks her between the two post lift and kills the engine as he leans in to pull the hood
  5. [2020-01-26 12:28:35] [Output] : ★ release handle. ((Marcus Wilburn))
  6. [2020-01-26 12:29:07] [Output] : ★ The hood latch pops as the hood slightly opens. ((Marcus Wilburn))
  7. [2020-01-26 12:29:27] [Output] : ★ Marcus Wilburn engages the handbrakes and opens the driver door before stepping out of the vehicle
  8. [2020-01-26 12:29:32] [Output] : ★ and shutting the said door. ((Marcus Wilburn))
  9. [2020-01-26 12:30:50] [Output] : ★ Marcus Wilburn walks to a corner of his garage and snatches a sleeveless jumpsuit from the hanger
  10. [2020-01-26 12:31:03] [Output] : ★ as he puts it on. ((Marcus Wilburn))
  11. [2020-01-26 12:31:31] [Output] : ★ Marcus Wilburn kneels down and undoes the laces on his Jordan Retro 5's, he then slips them off and
  12. [2020-01-26 12:31:52] [Output] : ★ puts on a pair of protective boots. ((Marcus Wilburn))
  13. [2020-01-26 12:32:30] [Output] : ★ Marcus Wilburn takes off his expensive chain along with a watch and puts them aside, he reaches out
  14. [2020-01-26 12:33:55] [Output] : ★ for a pair of protective gloves and slips them onto his hands, securing the scotch to ((Marcus Wilburn))
  15. [2020-01-26 12:33:58] [Output] : ★ tighten them. ((Marcus Wilburn))
  16. [2020-01-26 12:34:36] [Output] : ★ Marcus Wilburn looks over at the BMW, releasing a sigh as he's about to start a rather long journey
  17. [2020-01-26 12:34:56] [Output] : ★ of difficult tasks. ((Marcus Wilburn))
  18. [2020-01-26 12:36:15] [Output] : ★ Marcus Wilburn walks up to the workbench and grabs the bars of his trolley toolbox, he carts it
  19. [2020-01-26 12:36:24] [Output] : ★ in front of the BMW and leaves it there. ((Marcus Wilburn))
  20. [2020-01-26 12:36:49] [Output] : ★ Marcus Wilburn slides his fingers beneath the hood of the car and raises it up, applying the hood prop
  21. [2020-01-26 12:36:54] [Output] : ★ to fix it in place. ((Marcus Wilburn))
  22. [2020-01-26 12:37:28] [Output] : ★ Marcus Wilburn rubs his hands together as he stares at the hood of the engine, assessing the
  23. [2020-01-26 12:38:01] [Output] : ★ necessary work he has to do in order to get the engine out of the bay. ((Marcus Wilburn))
  24. [2020-01-26 12:39:02] [Output] : ★ Marcus Wilburn opens the top drawer of the tool box and takes out a flathead screwdriver, he then
  25. [2020-01-26 12:39:12] [Output] : ★ begins unscrewing the battery terminals. ((Marcus Wilburn))
  26. [2020-01-26 12:39:34] [Output] : ★ Marcus Wilburn puts the screwdriver back in its slot and disconnects the negative terminal.
  27. [2020-01-26 12:40:01] [Output] : ★ Marcus Wilburn grabs the positive one and pulls it off to disconnect it as well.
  28. [2020-01-26 12:40:38] [Output] : ★ Marcus Wilburn rummages through the different tools in the top drawer of the tool box, he grabs a
  29. [2020-01-26 12:41:05] [Output] : ★ ratchet and fits it with a 10mm socket before undoing the bolt that secures the ((Marcus Wilburn))
  30. [2020-01-26 12:41:19] [Output] : ★ battery strap in place. ((Marcus Wilburn))
  31. [2020-01-26 12:41:56] [Output] : ★ Marcus Wilburn saves the said bolt on top of the tool box and grabs the battery with both hands as
  32. [2020-01-26 12:42:11] [Output] : ★ he pulls it out of place, he heads to a corner of his garage where he gently drops it ((Marcus Wilburn))
  33. [2020-01-26 12:42:14] [Output] : ★ there for now. ((Marcus Wilburn))
  34. [2020-01-26 12:42:58] [Output] : ★ Marcus Wilburn walks back to the front of the BMW, he uses the ratchet with the same 10mm socket to
  35. [2020-01-26 12:43:19] [Output] : ★ undo the two bolts that secure the radiator's upper brackets to the car frame. ((Marcus Wilburn))
  36. [2020-01-26 12:43:53] [Output] : ★ Marcus Wilburn places the ratchet aside and reaches out for a torx screwdriver, he begins unscrewing
  37. [2020-01-26 12:44:11] [Output] : ★ the screws that mount the front bumper in place, he aims to remove it to achieve ((Marcus Wilburn))
  38. [2020-01-26 12:44:22] [Output] : ★ more clearance for the long engine removal process. ((Marcus Wilburn))
  39. [2020-01-26 12:44:41] [Output] : ★ Marcus Wilburn places the torx screwdriver back in place once he's done removing the front bumper
  40. [2020-01-26 12:45:18] [Output] : ★ screws, he slightly shakes the bumper to get it out of place before hauling it to the ((Marcus Wilburn))
  41. [2020-01-26 12:45:30] [Output] : ★ same corner he put the battery in, leaves it there. ((Marcus Wilburn))
  42. [2020-01-26 12:48:15] [Output] : ★ Marcus Wilburn heads back to the car and reaches out for his ratchet, he employs it to undo the bolts on
  43. [2020-01-26 12:48:30] [Output] : ★ the lower radiator brackets after he made clearance by removing the bumper. ((Marcus Wilburn))
  44. [2020-01-26 12:49:17] [Output] : ★ Marcus Wilburn puts the ratchet aside and manually unplugs the connector to the radiator fan.
  45. [2020-01-26 12:51:29] [Output] : ★ Marcus Wilburn holds a flathead screwdriver and starts undoing the clamps on the radiator ends of the
  46. [2020-01-26 12:51:33] [Output] : ★ radiator hoses. ((Marcus Wilburn))
  47. [2020-01-26 12:52:37] [Output] : ★ Marcus Wilburn is done loosening the clamps of the hoses connected to the radiator, he tilts the hoses
  48. [2020-01-26 12:53:02] [Output] : ★ to face the ceiling so that they don't make a mess with the coolant. ((Marcus Wilburn))
  49. [2020-01-26 12:53:26] [Output] : ★ Marcus Wilburn grasps onto the top of the radiator once it's completely loose, he grunts as he fishes
  50. [2020-01-26 12:53:32] [Output] : ★ it out of the engine bay. ((Marcus Wilburn))
  51. [2020-01-26 12:54:07] [Output] : ★ Marcus Wilburn places it near the rest of the removed parts and saves the bolts on top of the tool box.
  52. [2020-01-26 12:54:29] [Output] : ★ Marcus Wilburn uses the screwdriver to undo the clamps that secure to the radiator hoses to the
  53. [2020-01-26 12:55:22] [Output] : ★ engine's ports. ((Marcus Wilburn))
  54. [2020-01-26 12:55:58] [Output] : ★ Marcus Wilburn disconnects the radiator hoses and takes them off as he tosses them near the rest of the
  55. [2020-01-26 12:56:04] [Output] : ★ parts. ((Marcus Wilburn))
  56. [2020-01-26 12:57:49] [Output] : ★ Marcus Wilburn undoes the screws securing the overflow reservoir in place and takes that last
  57. [2020-01-26 12:58:11] [Output] : ★ near the rest of the parts, he places it in an empty plastic container so that the ((Marcus Wilburn))
  58. [2020-01-26 12:58:27] [Output] : ★ coolant leaking out of it doesn't come near the rest of the parts. ((Marcus Wilburn))
  59. [2020-01-26 12:59:14] [Output] : ★ Marcus Wilburn heads back to the front of the vehicle and finesses the ratchet as he fits it with a 16mm
  60. [2020-01-26 12:59:45] [Output] : ★ socket, he uses it to undo the two bolts of the hood bracket on the hood prop side. ((Marcus Wilburn))
  61. [2020-01-26 13:00:16] [Output] : ★ Marcus Wilburn saves the bolts in his pocket and employs the ratchet to loosen only one bolt on the other
  62. [2020-01-26 13:00:20] [Output] : ★ side of the hood bracket. ((Marcus Wilburn))
  63. [2020-01-26 13:00:47] [Output] : ★ Marcus Wilburn uses his left hand to hold the radiator up while reaching with his right one to undo the
  64. [2020-01-26 13:00:55] [Output] : ★ very last bolt on the left bracket. ((Marcus Wilburn))
  65. [2020-01-26 13:01:18] [Output] : ★ Marcus Wilburn pockets the two bolts and grabs the loose hood with both hands as he struggles to
  66. [2020-01-26 13:01:32] [Output] : ★ move it near the removed parts after disengaging the prop. ((Marcus Wilburn))
  67. [2020-01-26 13:01:53] [Output] : ★ Marcus Wilburn finally puts it down, he sighs in relief as he scratches his nose bridge.
  68. [2020-01-26 13:02:59] [Output] : ★ Marcus Wilburn gets his ratchet and fits it with a 10mm socket again, he undoes the bolts of the
  69. [2020-01-26 13:03:06] [Output] : ★ exhaust heat shield. ((Marcus Wilburn))
  70. [2020-01-26 13:04:14] [Output] : ★ Marcus Wilburn grabs the heat shield and tosses it far away in another corner, starting the collection of
  71. [2020-01-26 13:04:24] [Output] : ★ parts he won't need anymore since he's turbocharging the car. ((Marcus Wilburn))
  72. [2020-01-26 13:06:16] [Output] : ★ Marcus Wilburn fits the ratchet with a 14mm socket and undoes the bolts that secure the exhaust
  73. [2020-01-26 13:06:23] [Output] : ★ manifold to the engine head. ((Marcus Wilburn))
  74. [2020-01-26 13:06:56] [Output] : ★ The exhaust manifold is now sitting on the exhaust pipe. ((Marcus Wilburn))
  75. [2020-01-26 13:07:17] [Output] : ★ Marcus Wilburn uses the same socket and his ratchet to undo the two bolts on the exhaust manifold
  76. [2020-01-26 13:07:26] [Output] : ★ flange, unmounting it from the exhaust pipe. ((Marcus Wilburn))
  77. [2020-01-26 13:08:04] [Output] : ★ Marcus Wilburn grabs the said manifold and throws it near the exhaust shield, a rather loud bang
  78. [2020-01-26 13:08:17] [Output] : ★ echoes inside the vast garage. ((Marcus Wilburn))
  79. [2020-01-26 13:09:17] [Output] : ★ Marcus Wilburn moves to the driver side of the vehicle and drops on his knees as he moves the
  80. [2020-01-26 13:09:49] [Output] : ★ arms of that side of the 2-post lift beneath the BMW's pinch welds. ((Marcus Wilburn))
  81. [2020-01-26 13:10:15] [Output] : ★ Marcus Wilburn secures the arms and swiftly moves himself to the passenger side, kneeling down and
  82. [2020-01-26 13:10:43] [Output] : ★ lining up the lift's arm on that side with the bimmer's jack points. ((Marcus Wilburn))
  83. [2020-01-26 13:11:28] [Output] : ★ Marcus Wilburn goes to the workbench and takes hold of the lift remote, pressing on a button to
  84. [2020-01-26 13:12:16] [Output] : ★ lift the car about a meter above floor level. ((Marcus Wilburn))
  85. [2020-01-26 13:13:45] [Output] : ★ Marcus Wilburn gets his trolley laying pad and drops himself onto it before carting himself beneath the
  86. [2020-01-26 13:13:57] [Output] : ★ vehicle, and adjusting himself into a sitting position. ((Marcus Wilburn))
  87. [2020-01-26 13:14:42] [Output] : ★ Marcus Wilburn grasps on the O2 sensor's connector, he pulls it out of place.
  88. [2020-01-26 13:15:19] [Output] : ★ Marcus Wilburn gets the ratchet and starts undoing the exhaust hangers' bolts, he keeps adjusting
  89. [2020-01-26 13:15:37] [Output] : ★ his position in a way that when the exhaust is fully loose and dropping on the ground he ((Marcus Wilburn))
  90. [2020-01-26 13:15:44] [Output] : ★ wouldn't get hit with the pipes. ((Marcus Wilburn))
  91. [2020-01-26 13:16:16] [Output] : ★ Upon removing the last hanger bolt, the exhaust drops on the floor and produces a rather ((Marcus Wilburn))
  92. [2020-01-26 13:16:52] [Output] : ★ loud and sharp noise. ((Marcus Wilburn))
  93. [2020-01-26 13:17:31] [Output] : ★ Marcus Wilburn hauls himself away from beneath the car and pushes himself off of the creeper pad.
  94. [2020-01-26 13:17:54] [Output] : ★ Marcus Wilburn grabs the end of the exhaust assembly and pulls it away from the vehicle, leaving it
  95. [2020-01-26 13:17:59] [Output] : ★ near the removed parts. ((Marcus Wilburn))
  96. [2020-01-26 13:18:53] [Output] : ★ Marcus Wilburn takes hold of a plastic container and fits his ratchet with a 10mm socket prior to
  97. [2020-01-26 13:19:09] [Output] : ★ laying on his trolley creeper pad and moving beneath the transmission. ((Marcus Wilburn))
  98. [2020-01-26 13:19:30] [Output] : ★ Marcus Wilburn places the plastic container under the drain hole of the transmission and undoes
  99. [2020-01-26 13:19:54] [Output] : ★ the drain bolt, allowing the transmission oil to drain into the plastic container. ((Marcus Wilburn))
  100. [2020-01-26 13:20:35] [Output] : ★ Marcus Wilburn pushes himself up and temporarily removes his right hand's glove to light up a cigarette.
  101. [2020-01-26 13:20:59] [Output] : ★ Marcus Wilburn smokes on his cancer stick while waiting on the oil to drain, he walks around the
  102. [2020-01-26 13:21:33] [Output] : ★ garage and inspects the aftermarket parts he's about to install, seemingly so excited ((Marcus Wilburn))
  103. [2020-01-26 13:21:36] [Output] : ★ about it. ((Marcus Wilburn))
  104. [2020-01-26 13:32:47] [Output] : ★ Marcus Wilburn puts his cigarette out in the ashtray and slips the right glove back on, tightening it.
  105. [2020-01-26 13:34:04] [Output] : ★ The transmission oil completely clears out of the transmission and into the container. ((Marcus Wilburn))
  106. [2020-01-26 13:37:39] [Output] : ★ Marcus Wilburn moves the container aside and gets his transmission jack beneath the tranny prior to
  107. [2020-01-26 13:37:51] [Output] : ★ laying on his creeper pad and moving beneath the car. ((Marcus Wilburn))
  108. [2020-01-26 13:39:33] [Output] : ★ Marcus Wilburn pumps on the transmission jack level until the adapter is directly under the transmission
  109. [2020-01-26 13:39:37] [Output] : ★ supporting it. ((Marcus Wilburn))
  110. [2020-01-26 13:40:38] [Output] : ★ Marcus Wilburn grabs his air wrench and uses it to undo the bolts that secure the bell housing
  111. [2020-01-26 13:40:47] [Output] : ★ to the engine block. ((Marcus Wilburn))
  112. [2020-01-26 13:41:26] [Output] : ★ Marcus Wilburn disconnects the wire connectors to the transmission sensors.
  113. [2020-01-26 13:42:31] [Output] : ★ Marcus Wilburn fits the air wrench with a socket of the right size and loosens the bolts that secure the
  114. [2020-01-26 13:42:38] [Output] : ★ driveshaft to the transmission. ((Marcus Wilburn))
  115. [2020-01-26 13:44:56] [Output] : ★ Marcus Wilburn wraps the jack's belt around the bellhousing and straps it down as he secures it as
  116. [2020-01-26 13:45:00] [Output] : ★ tightly as possible. ((Marcus Wilburn))
  117. [2020-01-26 13:46:22] [Output] : ★ Marcus Wilburn starts wiggling the transmission off to seperate it from the engine, he then uses the jack
  118. [2020-01-26 13:46:41] [Output] : ★ lever to lower the transmission, he carts the transmission jack out from beneath the ((Marcus Wilburn))
  119. [2020-01-26 13:46:43] [Output] : ★ engine. ((Marcus Wilburn))
  120. [2020-01-26 13:47:23] [Output] : ★ Marcus Wilburn puts it aside and gets back beneath the vehicle, using his air wrench to undo both
  121. [2020-01-26 13:48:02] [Output] : ★ the bolts on the torque converter and the flywheel, loosening them. ((Marcus Wilburn))
  122. [2020-01-26 13:48:19] [Output] : ★ Marcus Wilburn takes both parts and carelessly tosses them near the rest of the removed parts
  123. [2020-01-26 13:48:24] [Output] : ★ he no further needs. ((Marcus Wilburn))
  124. [2020-01-26 13:53:35] [Output] : ★ Marcus Wilburn pushes himself up and presses a button on the lift remote to lower the vehicle down
  125. [2020-01-26 13:53:41] [Output] : ★ to floor level. ((Marcus Wilburn))
  126. [2020-01-26 14:00:34] [Output] : ★ Marcus Wilburn gets his ratchet fitted with a 10mm socket and undoes the bolts securing the airbox in
  127. [2020-01-26 14:00:54] [Output] : ★ place before putting the ratchet aside and using his screwdriver to undo the clamp ((Marcus Wilburn))
  128. [2020-01-26 14:01:17] [Output] : ★ securing the air pipe connected to the airbox, he disconnects it and takes the airbox ((Marcus Wilburn))
  129. [2020-01-26 14:01:28] [Output] : ★ out of the bay, putting it down near the rest of removed parts. ((Marcus Wilburn))
  130. [2020-01-26 14:02:48] [Output] : ★ Marcus Wilburn saves the bolts and loosens the clamp tightening the air pipe to the throttle body.
  131. [2020-01-26 14:04:05] [Output] : ★ Marcus Wilburn removes the said pipe and carelessly launches it in the air away from the car.
  132. [2020-01-26 14:04:53] [Output] : ★ Marcus Wilburn unhooks the throttle cable from the throttle body and grabs a towel as he places it beneath
  133. [2020-01-26 14:05:06] [Output] : ★ the engine to catch any fuel that drips during the removal process. ((Marcus Wilburn))
  134. [2020-01-26 14:06:00] [Output] : ★ Marcus Wilburn uses the flathead screwdriver to loosen the clamps on the fuel feed and fuel return
  135. [2020-01-26 14:06:04] [Output] : ★ pipes. ((Marcus Wilburn))
  136. [2020-01-26 14:08:40] [Output] : ★ Marcus Wilburn unplugs the fuel intake and fuel return lines off of the fuel rail.
  137. [2020-01-26 14:09:18] [Output] : ★ Fuel idling in the fuel lines starts dripping on the cloth that Marcus has placed ((Marcus Wilburn))
  138. [2020-01-26 14:09:21] [Output] : ★ beneath the car. ((Marcus Wilburn))
  139. [2020-01-26 14:10:08] [Output] : * Marcus Wilburn's cellphone starts to ring. *
  140. [2020-01-26 14:10:08] [Output] : Your phone #789418 has received a new text message.
  141. [2020-01-26 14:12:24] [Output] : ★ Marcus Wilburn starts unplugging the sensor connectors and the rest of the wire connections to
  142. [2020-01-26 14:12:43] [Output] : ★ completely loosen the wire loom, he then tucks it to the side where it won't get caught ((Marcus Wilburn))
  143. [2020-01-26 14:12:51] [Output] : ★ by the engine when it's being removed. ((Marcus Wilburn))
  144. [2020-01-26 14:14:16] [Output] : ★ Marcus Wilburn undoes the bolts securing the intake manifold to the engine head using his ratchet
  145. [2020-01-26 14:15:31] [Output] : ★ and 14mm socket, he wiggles it off as he unmounts it and throws it away. ((Marcus Wilburn))
  146. [2020-01-26 14:15:58] [Output] : ★ Marcus Wilburn will no longer need the said part, he doesn't really mind anything on it breaking.
  147. [2020-01-26 14:18:08] [Output] : ★ Marcus Wilburn uses his ratchet to loosen the belt tensioner, he takes the belt out and puts it aside
  148. [2020-01-26 14:19:19] [Output] : ★ before starting to undo the refrigerant lines on the A/C compressor, he then undoes the bolt ((Marcus Wilburn))
  149. [2020-01-26 14:19:42] [Output] : ★ on the A/C compressor bracket and jiggles it out of its slot. ((Marcus Wilburn))
  150. [2020-01-26 14:20:31] [Output] : ★ Marcus Wilburn carts the engine hoist in front of the car and inserts two special bolts in the holes of the
  151. [2020-01-26 14:21:00] [Output] : ★ intake manifold's original place, he runs the hoist's chain through them and does the same ((Marcus Wilburn))
  152. [2020-01-26 14:21:26] [Output] : ★ with the exhaust manifold mounting holes to ensure more control with the removal of the ((Marcus Wilburn))
  153. [2020-01-26 14:21:28] [Output] : ★ engine. ((Marcus Wilburn))
  154. [2020-01-26 14:22:02] [Output] : ★ Marcus Wilburn grabs the hoist lever and starts pumping with his eyes fixed on the engine as it
  155. [2020-01-26 14:22:31] [Output] : ★ sits there, he stops and gets beneath the car to undo the motor mounts, being so silly ((Marcus Wilburn))
  156. [2020-01-26 14:22:36] [Output] : ★ he almost forgot them. ((Marcus Wilburn))
  157. [2020-01-26 14:23:00] [Output] : ★ Marcus Wilburn finally loosens the motor mounts with his ratchet, the engine is now ready to be removed.
  158. [2020-01-26 14:23:20] [Output] : ★ Marcus Wilburn mans the hoist and keeps on pumping the lever, his eyes following the engine as he
  159. [2020-01-26 14:23:39] [Output] : ★ makes sure the engine damages nothing on its way out, he adjusts the settings on the ((Marcus Wilburn))
  160. [2020-01-26 14:23:52] [Output] : ★ leveler accordingly to ensure a clean pull. ((Marcus Wilburn))
  161. [2020-01-26 14:25:05] [Output] : ★ Marcus Wilburn carts the engine hoist near the engine stand and rotates it in a way the the bellhousing
  162. [2020-01-26 14:26:03] [Output] : ★ holes are facing the engine stand's head plate. ((Marcus Wilburn))
  163. [2020-01-26 14:26:39] [Output] : ★ Marcus Wilburn matches the level of the engine with the level of the mounting arms and lines them up
  164. [2020-01-26 14:27:34] [Output] : ★ properly before tightening the arms to secure the engine onto the stand. ((Marcus Wilburn))
  165. [2020-01-26 14:28:04] [Output] : ★ Marcus Wilburn uses a ratchet to undo the bolts that secure the hoist chain to the engine to release it.
  166. [2020-01-26 14:28:36] [Output] : ★ Marcus Wilburn pushes the engine hoist back to its place as he no longer needs it, he heads back to
  167. [2020-01-26 14:28:42] [Output] : ★ the engine stand. ((Marcus Wilburn))
  168. [2020-01-26 14:30:28] [Output] : ★ Marcus Wilburn carts the engine stand near his workbench and puts two clean towels on the table
  169. [2020-01-26 14:30:35] [Output] : ★ for the parts he removes. ((Marcus Wilburn))
  170. [2020-01-26 14:31:03] [Output] : ★ Marcus Wilburn uses his air wrench to undo the four bolts that secure the water pump in place, he then
  171. [2020-01-26 14:31:28] [Output] : ★ puts it on the towel with the bolts just next to it. ((Marcus Wilburn))
  172. [2020-01-26 14:32:23] [Output] : ★ Marcus Wilburn fits the air wrench with an allen socket and uses it to undo the allen bolts that hold
  173. [2020-01-26 14:32:33] [Output] : ★ the timing cover in place. ((Marcus Wilburn))
  174. [2020-01-26 14:33:35] [Output] : ★ Marcus Wilburn grasps on the first coil wire, he takes it off as he moves to the second one and doing
  175. [2020-01-26 14:35:11] [Output] : ★ exactly the same process to remove it, he goes through every coil plug and pulls it out. ((Marcus Wilburn))
  176. [2020-01-26 14:36:10] [Output] : ★ Marcus Wilburn fits the ratchet with an extension bar and the extension bar itself with a spark plug
  177. [2020-01-26 14:36:23] [Output] : ★ socket before beginning to take the spark plugs out of the holes. ((Marcus Wilburn))
  178. [2020-01-26 14:37:28] [Output] : ★ Marcus Wilburn sets them aside and grabs his impact wrench, struggling to undo the crack pulley.
  179. [2020-01-26 14:38:05] [Output] : ★ Marcus Wilburn keeps on trying to take off crack pulley's bolt, he places the impact wrench aside after
  180. [2020-01-26 14:38:44] [Output] : ★ coming to realize it won't work, he grabs two flywheel bolts and puts them in the back ((Marcus Wilburn))
  181. [2020-01-26 14:39:10] [Output] : ★ of the crankshaft and wedges a pry bar in there before getting on the front with a huge ((Marcus Wilburn))
  182. [2020-01-26 14:39:45] [Output] : ★ breaker bar and literally starts lifting himself off the ground as he pushes the ((Marcus Wilburn))
  183. [2020-01-26 14:40:09] [Output] : ★ breaker bar down in the right direction to finally loosen the crank pulley bolt ((Marcus Wilburn))
  184. [2020-01-26 14:40:46] [Output] : ★ Marcus Wilburn places the pry bar and the breaker bar aside and reaches out for the crank pulley special
  185. [2020-01-26 14:41:48] [Output] : ★ puller tool, he inserts the tool's bolts in the threaded bungs on the pulley and starts ((Marcus Wilburn))
  186. [2020-01-26 14:41:59] [Output] : ★ pulling the tool out to eventually get the pully off. ((Marcus Wilburn))
  187. [2020-01-26 14:42:22] [Output] : ★ Marcus Wilburn puts the pulley on the table and hooks off the puller tool as he puts it in place.
  188. [2020-01-26 14:43:20] [Output] : ★ Marcus Wilburn uses the impact wrench in order to loosen all four bolts securing the automatic tensioner
  189. [2020-01-26 14:43:27] [Output] : ★ of the serpentine belt. ((Marcus Wilburn))
  190. [2020-01-26 14:43:53] [Output] : ★ Marcus Wilburn places the tensioner aside and finishes removing the plastic timing cover after he undoes
  191. [2020-01-26 14:43:59] [Output] : ★ the bolts securing it in place. ((Marcus Wilburn))
  192. [2020-01-26 14:44:32] [Output] : ★ Marcus Wilburn fits the impact wrench with a 10mm socket and starts removing the valve cover bolts.
  193. [2020-01-26 14:45:07] [Output] : ★ Marcus Wilburn puts the impact wrench aside and grabs a pair of needlenose pliers, using them to
  194. [2020-01-26 14:45:26] [Output] : ★ take off the rubber grommets that are stuck due to the aging. ((Marcus Wilburn))
  195. [2020-01-26 14:47:01] [Output] : ★ Marcus Wilburn puts the needlenose pliers back in the tool box. he wedges the end of his pry bar between
  196. [2020-01-26 14:47:21] [Output] : ★ the valve covers and pushes away to pop them off. ((Marcus Wilburn))
  197. [2020-01-26 14:47:48] [Output] : ★ Marcus Wilburn places the cover on the table and emits a sigh as he wipes his forehead with his
  198. [2020-01-26 14:47:52] [Output] : ★ forearm. ((Marcus Wilburn))
  199. [2020-01-26 14:48:27] [Output] : ★ Marcus Wilburn grabs the crank pulley bolt and hand tightens it before grabbing the impact wrench and
  200. [2020-01-26 14:48:31] [Output] : ★ tightening it. ((Marcus Wilburn))
  201. [2020-01-26 14:49:12] [Output] : ★ Marcus Wilburn fits his ratchet with a socket of the size of the crank pulley bolt and turns it until
  202. [2020-01-26 14:49:32] [Output] : ★ the timing system is on top dead center. ((Marcus Wilburn))
  203. [2020-01-26 14:50:17] [Output] : ★ Marcus Wilburn fits the ratchet with a 10mm socket and loosens the crankshaft angle sensor's
  204. [2020-01-26 14:50:33] [Output] : ★ bolt prior to pulling it out of its place and placing it on the table. ((Marcus Wilburn))
  205. [2020-01-26 14:51:14] [Output] : ★ Marcus Wilburn slips the timing belt off and saves it on the table, exhaling deeply.
  206. [2020-01-26 14:51:55] [Output] : ★ Marcus Wilburn fits the ratcheting wrench with a 15mm socket and employs it to undo the bolt on the
  207. [2020-01-26 14:52:14] [Output] : ★ exhaust camshaft gear, he takes off the said gear and puts on the table. ((Marcus Wilburn))
  208. [2020-01-26 14:53:50] [Output] : ★ Marcus Wilburn pulls out the variable cam solenoid that acts as a sensor for the VANOS on the
  209. [2020-01-26 14:53:55] [Output] : ★ intake cam. ((Marcus Wilburn))
  210. [2020-01-26 14:54:32] [Output] : ★ Marcus Wilburn places it on the table and uses the impact wrench to pull out the inatke cam bolt that is
  211. [2020-01-26 14:54:37] [Output] : ★ a cover to a hex bolt. ((Marcus Wilburn))
  212. [2020-01-26 14:55:14] [Output] : ★ Marcus Wilburn grabs a monkey wrench and adjusts the settings on it to hold the intake cam
  213. [2020-01-26 14:55:33] [Output] : ★ while he uses a breaker bar with the hex socket to undo the intake cam gear. ((Marcus Wilburn))
  214. [2020-01-26 14:56:13] [Output] : ★ Marcus Wilburn places the tools in place and pulls the intake gear out as he puts it next to the exhaust
  215. [2020-01-26 14:56:29] [Output] : ★ cam gear with the bolts that are associated with it laying next to it. ((Marcus Wilburn))
  216. [2020-01-26 14:57:42] [Output] : ★ Marcus Wilburn undoes the 10mm bolts securing a plastic cover on the side of the camshaft gears
  217. [2020-01-26 14:57:42] [Output] : ADVERT: 2006 Honda CBR-600RR - $8,000. Good condition still, Fast. | #751245 (( Jessica McGreenland ))
  218. [2020-01-26 14:58:09] [Output] : ★ of the engine head, he puts it aside and utilizes the impact wrench to remove ((Marcus Wilburn))
  219. [2020-01-26 14:58:44] [Output] : ★ the two bolts securing the hard line that feeds oil from the block to the head. ((Marcus Wilburn))
  220. [2020-01-26 14:59:02] [Output] : ★ Marcus Wilburn gets the bango bolt out of its little filter and sets it aside.
  221. [2020-01-26 14:59:28] [Output] : ★ Marcus Wilburn removes the actual hard oil line and sets it aside as well.
  222. [2020-01-26 15:00:13] [Output] : ★ Marcus Wilburn double checks the camshafts to make sure he's at top dead center, he uses
  223. [2020-01-26 15:00:29] [Output] : ★ the breaker bar to break loose all the camshafts bolts. ((Marcus Wilburn))
  224. [2020-01-26 15:00:57] [Output] : ★ Marcus Wilburn moves from the outside in as he undoes the said bolts, both camshafts pop up a
  225. [2020-01-26 15:01:35] [Output] : ★ little once the bolts are loose, affected by the pressure applied by the valve springs. ((Marcus Wilburn))
  226. [2020-01-26 15:04:06] [Output] : ★ Marcus Wilburn starts removing the cam caps from the outside in and placing them on the table
  227. [2020-01-26 15:04:30] [Output] : ★ following the same order he removed them with so that he knows which goes where ((Marcus Wilburn))
  228. [2020-01-26 15:04:39] [Output] : ★ when reassembling the inline-6. ((Marcus Wilburn))
  229. [2020-01-26 15:06:05] [Output] : ★ Marcus Wilburn removes the intake and exhaust cams not really concerned whether they break or not
  230. [2020-01-26 15:06:24] [Output] : ★ seeing that he's going to replace these two, he tosses them near the rest of parts ((Marcus Wilburn))
  231. [2020-01-26 15:06:29] [Output] : ★ he earlier removed. ((Marcus Wilburn))
  232. [2020-01-26 15:07:35] [Output] : ★ Marcus Wilburn grabs a bottle of alcohol and twists off the cap before pouring some on a microfiber towel
  233. [2020-01-26 15:08:58] [Output] : ★ and using the said towel to wipe off the valve buckets. ((Marcus Wilburn))
  234. [2020-01-26 15:11:12] [Output] : ★ Marcus Wilburn gets a marker and labels the buckets before using a magnet to pull them out of place.
  235. [2020-01-26 15:11:40] [Output] : ★ Marcus Wilburn places them on the table in the same order they used to have when they were mounted.
  236. [2020-01-26 15:13:05] [Output] : ★ Marcus Wilburn fits a 12mm spline drive on his ratchet and begins to loosen the cylinder head bolts.
  237. [2020-01-26 15:13:50] [Output] : ★ Marcus Wilburn places the removed bolts on the table next to each other and uses his magnet to pull
  238. [2020-01-26 15:13:54] [Output] : ★ their washers out. ((Marcus Wilburn))
  239. [2020-01-26 15:14:25] [Output] : ★ Marcus Wilburn takes a firm grip of the cylinder head now that the bolts are all loose, he lifts it up and
  240. [2020-01-26 15:14:39] [Output] : ★ rests it on the workbench. ((Marcus Wilburn))
  241. [2020-01-26 15:20:48] [Output] : ★ Marcus Wilburn takes off the old head gasket and puts it on the table.
  242. [2020-01-26 17:41:18] [Output] : ★ Marcus Wilburn grabs a huge plastic container and gets it beneath the engine as he fits his ratchet with
  243. [2020-01-26 17:41:39] [Output] : ★ a 10mm socket and undoes the bolts on the oil pan. ((Marcus Wilburn))
  244. [2020-01-26 17:42:00] [Output] : ★ Marcus Wilburn puts the bolts aside and grabs a pry bar, wedging it between the oil pan and the block as
  245. [2020-01-26 17:42:13] [Output] : ★ he pushes away while supporting oil pan with his left hand. ((Marcus Wilburn))
  246. [2020-01-26 17:42:43] [Output] : ★ Marcus Wilburn pours the oil from the oil pan in the sad container and places it aside.
  247. [2020-01-26 17:45:27] [Output] : ★ Marcus Wilburn grabs the engine stand lever and starts turning it until the engine is upside down.
  248. [2020-01-26 17:46:26] [Output] : ★ Marcus Wilburn uses the impact wrench to undo the two bolts securing the oil strainer, he takes it off and
  249. [2020-01-26 17:46:44] [Output] : ★ puts it on the table along with the bolts. ((Marcus Wilburn))
  250. [2020-01-26 17:47:02] [Output] : ★ Marcus Wilburn gets back to the impact wrench and uses this last to loosen the bolts on the
  251. [2020-01-26 17:47:36] [Output] : ★ oil baffle splash screen, he puts it aside as well. ((Marcus Wilburn))
  252. [2020-01-26 17:48:13] [Output] : ★ Marcus Wilburn unscrews the bolt on the oil level sensor and pulls it out of its hole, saving it on the
  253. [2020-01-26 17:48:16] [Output] : ★ table. ((Marcus Wilburn))
  254. [2020-01-26 17:50:24] [Output] : ★ Marcus Wilburn uses his breaker bar and a socket of the right size to break loose all the bolts securing
  255. [2020-01-26 17:50:46] [Output] : ★ the bedplate, he then finishes the removal job using his ratchet. ((Marcus Wilburn))
  256. [2020-01-26 17:51:02] [Output] : ★ Marcus Wilburn grabs both sides of the bedplate and places it on the table.
  257. [2020-01-26 17:51:29] [Output] : ★ Marcus Wilburn reveals the crankshaft and the rods and all the main caps by removing the bedplate.
  258. [2020-01-26 17:52:21] [Output] : ★ Marcus Wilburn rubs his hands together as he grabs the special tool and hooks it up on the crankshaft
  259. [2020-01-26 17:52:54] [Output] : ★ gear, he starts slowly unscrewing the bolt on the tool to get the gear out of place. ((Marcus Wilburn))
  260. [2020-01-26 17:53:35] [Output] : ★ Marcus Wilburn places the tool and the gear away, he then uses the impact wrench to remove the two
  261. [2020-01-26 17:53:43] [Output] : ★ bolts securing the oil pump assembly. ((Marcus Wilburn))
  262. [2020-01-26 17:54:04] [Output] : ★ Marcus Wilburn wedges a pry bar between the said assembly and the block once it's finally loose, he pushes
  263. [2020-01-26 17:54:09] [Output] : ★ away and pops it off. ((Marcus Wilburn))
  264. [2020-01-26 17:54:20] [Output] : ★ Marcus Wilburn catches the oil pump assembly and rests it on the table.
  265. [2020-01-26 17:56:49] [Output] : ★ Marcus Wilburn pulls off the rear main seal and puts it on the table before grabbing a scrotch brite and
  266. [2020-01-26 17:57:37] [Output] : ★ rubbing the carbon deposits off of the cylinders, he turns the crankshaft to move the ((Marcus Wilburn))
  267. [2020-01-26 17:57:48] [Output] : ★ pistons up and down for clearance when he has to. ((Marcus Wilburn))
  268. [2020-01-26 17:59:01] [Output] : ★ Marcus Wilburn finishes removing the carbon deposits, he then tosses the dirty scotch brite away.
  269. [2020-01-26 18:00:25] [Output] : ★ Marcus Wilburn uses a breaker bar to break loose the two bolts on the cap securing the first piston
  270. [2020-01-26 18:00:29] [Output] : ★ to the crankshaft. ((Marcus Wilburn))
  271. [2020-01-26 18:01:01] [Output] : ★ Marcus Wilburn puts the breaker bar aside and grabs a rubber malet as he gives the bolts he just
  272. [2020-01-26 18:01:19] [Output] : ★ loosened a knock. ((Marcus Wilburn))
  273. [2020-01-26 18:02:10] [Output] : ★ Marcus Wilburn puts the mallet aside and finishes the removing the two bolts on the cap.
  274. [2020-01-26 18:02:30] [Output] : ★ Marcus Wilburn places the cap and the two bolts on the table and moves his left hand beneath the cylinder
  275. [2020-01-26 18:02:51] [Output] : ★ as he uses his right one to push on the pistol, eventually the piston falls and Marcus ((Marcus Wilburn))
  276. [2020-01-26 18:02:56] [Output] : ★ catches it with his left hand. ((Marcus Wilburn))
  277. [2020-01-26 18:04:58] [Output] : ★ Marcus Wilburn does exactly the same process with the each one of the rest 5 pistons, he tosses
  278. [2020-01-26 18:05:06] [Output] : ★ them near the parts he won't need anymore. ((Marcus Wilburn))
  279. [2020-01-26 18:39:30] [Output] : ★ Marcus Wilburn grabs a breaker bar and a 15mm socket, he breaks loose all the bolts on the main caps.
  280. [2020-01-26 18:40:18] [Output] : ★ Marcus Wilburn fits the same socket on the ratchet after he's done with the breaker bar, he completely
  281. [2020-01-26 18:40:44] [Output] : ★ takes the main cap bolts off and starts removing the main caps, placing them aside. ((Marcus Wilburn))
  282. [2020-01-26 18:42:33] [Output] : ★ Marcus Wilburn grabs the crankshaft itself and fishes it out of place as he sets it near the rest of
  283. [2020-01-26 18:42:37] [Output] : ★ the parts. ((Marcus Wilburn))
  284. [2020-01-26 19:31:59] [Output] : ★ Marcus Wilburn grabs a transmission jack and pumps the lever until the plate is directly beneath the engine
  285. [2020-01-26 19:32:02] [Output] : ★ block. ((Marcus Wilburn))
  286. [2020-01-26 19:32:33] [Output] : ★ Marcus Wilburn secures the strap around the engine to hold it in place and unbolts the engine mount
  287. [2020-01-26 19:32:48] [Output] : ★ arms to separate the engine from the engine stand. ((Marcus Wilburn))
  288. [2020-01-26 19:33:17] [Output] : ★ Marcus Wilburn carts the block to the jet wash tank machine and pulls the lid open.
  289. [2020-01-26 19:33:35] [Output] : ★ Marcus Wilburn undoes the strap and takes a firm grip of the block before moving it inside.
  290. [2020-01-26 19:35:44] [Output] : ★ Marcus Wilburn shuts the lid and turns on the machine as he sits back and watch it spray extremely hot and
  291. [2020-01-26 19:36:02] [Output] : ★ pressurized water against the block to get it clean. ((Marcus Wilburn))
  292. [2020-01-26 19:37:20] [Output] : ★ Marcus Wilburn lets the machine do what has to be done he heads to the workbench where the
  293. [2020-01-26 19:37:26] [Output] : ★ cylinder head is. ((Marcus Wilburn))
  294. [2020-01-26 19:40:41] [Output] : ★ Marcus Wilburn grabs a valve compressor machine and adjusts the length of the tool by turning the
  295. [2020-01-26 19:40:55] [Output] : ★ bolt before mounting it on the first valve. ((Marcus Wilburn))
  296. [2020-01-26 19:41:29] [Output] : ★ Marcus Wilburn moves the lever and causes the first valve spring to compress, the valve keeps falls
  297. [2020-01-26 19:41:36] [Output] : ★ away. ((Marcus Wilburn))
  298. [2020-01-26 19:41:39] [Output] : ★ keeper* ((Marcus Wilburn))
  299. [2020-01-26 19:42:49] [Output] : ★ Marcus Wilburn releases tension on the tool, the valve spring comes up loose.
  300. [2020-01-26 19:43:24] [Output] : ★ Marcus Wilburn grabs the spring and takes it off as he tosses it aside.
  301. [2020-01-26 19:45:30] [Output] : ★ Marcus Wilburn pushes the valve out of place once the spring is loose, he puts it on the table.
  302. [2020-01-26 19:46:34] [Output] : ★ Marcus Wilburn uses the special valve compressor tool to take off the rest of the valves he carelessly
  303. [2020-01-26 19:47:00] [Output] : ★ throws away the springs and their keepers along with the retainers and saves the ((Marcus Wilburn))
  304. [2020-01-26 19:47:02] [Output] : ★ valves. ((Marcus Wilburn))
  305. [2020-01-26 19:47:37] [Output] : ★ Marcus Wilburn collects all 24 valves on the table and heads back to the jet wash tank machine.
  306. [2020-01-26 19:48:12] [Output] : ★ Marcus Wilburn turns it off and pulls the lid open, steam comes out of the machine pretty much covering the
  307. [2020-01-26 19:48:29] [Output] : ★ view that Marcus is excited to see, the look of the clean engine block. ((Marcus Wilburn))
  308. [2020-01-26 19:49:00] [Output] : ★ Marcus Wilburn steps away and takes off his right glove as he lights up a cigarette and watches the
  309. [2020-01-26 19:49:17] [Output] : ★ jet washer machine as he waits the block to cool down and the steam to go away. ((Marcus Wilburn))
  310. [2020-01-26 19:54:07] [Output] : ★ Marcus Wilburn puts out his cigarette and puts his heat protective glove back on before heading to
  311. [2020-01-26 19:54:35] [Output] : ★ the jet washer machine and grabbing both sides of the engine as he ((Marcus Wilburn))
  312. [2020-01-26 19:54:54] [Output] : ★ lets out a grunt, lifting the inline six out of there and quickly resting it on the ((Marcus Wilburn))
  313. [2020-01-26 19:55:02] [Output] : ★ transmission jack's plate. ((Marcus Wilburn))
  314. [2020-01-26 19:55:33] [Output] : ★ Marcus Wilburn wraps the strap around it and secures it before moving it to the workbench and
  315. [2020-01-26 19:55:46] [Output] : ★ unstrapping it. ((Marcus Wilburn))
  316. [2020-01-26 19:57:25] [Output] : ★ Marcus Wilburn moves it on top of the workbench and plugs his polishing machine into electricity.
  317. [2020-01-26 19:58:04] [Output] : ★ Marcus Wilburn twists the cap off of the polishing product's bottle, he pours some on the engine block and
  318. [2020-01-26 19:58:29] [Output] : ★ uses the machine to spread it around and give the block that shiny look. ((Marcus Wilburn))
  319. [2020-01-26 19:59:06] [Output] : ★ Marcus Wilburn would have of course polished it after wiping off everything with a dry towel.
  320. [2020-01-26 20:00:16] [Output] : ★ Marcus Wilburn turns on the belt sander machine and takes the first main cap as he champhers it
  321. [2020-01-26 20:00:31] [Output] : ★ against the moving belt. ((Marcus Wilburn))
  322. [2020-01-26 20:00:49] [Output] : ★ Marcus Wilburn places the said main cap aside and reaches for another, grinding the surfaces again
  323. [2020-01-26 20:01:12] [Output] : ★ to achieve a neat right-angled edge. ((Marcus Wilburn))
  324. [2020-01-26 20:01:36] [Output] : ★ Marcus Wilburn sets that cap aside as well and spends his time doing the same for the rest of the main
  325. [2020-01-26 20:01:38] [Output] : ★ caps. ((Marcus Wilburn))
  326. [2020-01-26 20:03:21] [Output] : There is currently one taxi available in Red County! Call 8294 for a pickup.
  327. [2020-01-26 20:04:16] [Output] : ★ Marcus Wilburn files the edges of the surfaces where the main caps are the supposed to be mounted on
  328. [2020-01-26 20:05:01] [Output] : ★ the block using a filing tool, he then puts it aside and grabs the main caps as he puts them ((Marcus Wilburn))
  329. [2020-01-26 20:05:31] [Output] : ★ where they're supposed to go, he grabs a bottle of bolt lube and takes off the cap ((Marcus Wilburn))
  330. [2020-01-26 20:06:52] [Output] : ★ prior using a brush to apply the lube to the main cap mounting holes. ((Marcus Wilburn))
  331. [2020-01-26 20:07:10] [Output] : ★ Marcus Wilburn puts away the bolt lube bottle after closing it.
  332. [2020-01-26 20:07:43] [Output] : ★ Marcus Wilburn collects the main cap bolts and uses his ratcheting wrench to secure them tightly.
  333. [2020-01-26 20:08:07] [Output] : ★ Marcus Wilburn holds his torque wrench and fits it with the socket of the right size prior to
  334. [2020-01-26 20:08:46] [Output] : ★ torquing the main cap bolts to the specs that he just looked at in the car manual. ((Marcus Wilburn))
  335. [2020-01-26 20:10:14] [Output] : ★ Marcus Wilburn opens the CNC machine lid and keeps it open as he heads to the block
  336. [2020-01-26 20:10:35] [Output] : ★ and carries it up, he then moves it inside the machine and closes the lid. ((Marcus Wilburn))
  337. [2020-01-26 20:12:09] [Output] : ★ Marcus Wilburn turns on the computer connected to the said machine and starts filling the necessary
  338. [2020-01-26 20:12:57] [Output] : ★ settings such as the rollover clearance the cylinder diameter and angle. ((Marcus Wilburn))
  339. [2020-01-26 20:13:57] [Output] : ★ Marcus Wilburn sets the roughing RPM to 275 and the finish RPM to 215 before setting the bore locations to
  340. [2020-01-26 20:14:03] [Output] : ★ automatic detection. ((Marcus Wilburn))
  341. [2020-01-26 20:14:37] [Output] : ★ Marcus Wilburn activates the Z crash detection and goes through the parameters again to ensure
  342. [2020-01-26 20:14:50] [Output] : ★ that everything will go fine with the cylinder honing process. ((Marcus Wilburn))
  343. [2020-01-26 20:15:33] [Output] : ★ An alert pops up, indicating that the lubricant level is low. ((Marcus Wilburn))
  344. [2020-01-26 20:16:00] [Output] : ★ Marcus Wilburn pushes himself up and grabs a bottle of lubricant before twisting the cap off of the
  345. [2020-01-26 20:16:20] [Output] : ★ filling slot, he pours the whole bottle inside and puts the cap back on. ((Marcus Wilburn))
  346. [2020-01-26 20:17:00] [Output] : ★ Marcus Wilburn shuts the CNC machine lid and clicks on a "Start cycle" button on the computer.
  347. [2020-01-26 20:18:10] [Output] : ★ The tip of the machine slowly moves down, it appears to have a sensor on the end ((Marcus Wilburn))
  348. [2020-01-26 20:19:02] [Output] : ★ that automatically identifies the location of each cylinders by going against the walls ((Marcus Wilburn))
  349. [2020-01-26 20:19:17] [Output] : ★ of each cylinder, moving from one to another. ((Marcus Wilburn))
  350. [2020-01-26 20:20:00] [Output] : ★ The tool raises up again, a mechanism switches from the tip with the sensor to another ((Marcus Wilburn))
  351. [2020-01-26 20:20:15] [Output] : ★ which is the honing tool. ((Marcus Wilburn))
  352. [2020-01-26 20:20:38] [Output] : ★ Marcus Wilburn sparks up a cigarette and watches the machine does all the magic.
  353. [2020-01-26 20:21:11] [Output] : ★ The machine lines up the honing tool with the first cylinder, it slowly moves the tool ((Marcus Wilburn))
  354. [2020-01-26 20:22:15] [Output] : ★ down until it's inside the bore, the tool expands until its diameter is equal to the bore's. ((Marcus Wilburn))
  355. [2020-01-26 20:22:52] [Output] : ★ The tool starts spinning with the RPM defined by Marcus before the start of the cycle while ((Marcus Wilburn))
  356. [2020-01-26 20:23:16] [Output] : ★ a hose shoots lubricant inside the bore to ensure a clean operation and to keep the iron ((Marcus Wilburn))
  357. [2020-01-26 20:23:25] [Output] : ★ cool throughout the process. ((Marcus Wilburn))
  358. [2020-01-26 20:25:54] [Output] : ★ The machine's tip continuously goes up and down the cylinder as it hones it, producting ((Marcus Wilburn))
  359. [2020-01-26 20:26:17] [Output] : ★ extremely annoying creaking sounds. ((Marcus Wilburn))
  360. [2020-01-26 20:27:21] [Output] : ★ The tip rises out of the first cylinder and the machine stops pumping lubricant, it slowly ((Marcus Wilburn))
  361. [2020-01-26 20:27:46] [Output] : ★ moves exactly above the second cylinder and hovers above it before slowly ((Marcus Wilburn))
  362. [2020-01-26 20:28:17] [Output] : ★ dropping down inside it and honing the second one as the lubricant gets pumped into that ((Marcus Wilburn))
  363. [2020-01-26 20:28:32] [Output] : ★ cylinder. ((Marcus Wilburn))
  364. [2020-01-26 20:28:52] [Output] : ★ The machine does exactly the same process with the rest of the four cylinders as it ((Marcus Wilburn))
  365. [2020-01-26 20:29:02] [Output] : ★ pulls a rather clean honing job. ((Marcus Wilburn))
  366. [2020-01-26 20:29:37] [Output] : ★ The whole process takes around ten minutes. ((Marcus Wilburn))
  367. [2020-01-26 20:30:00] [Output] : ★ Marcus Wilburn puts out his cigarette and takes his phone out as he browses his Instagram feed
  368. [2020-01-26 20:30:18] [Output] : ★ casually looking up at the machine and the screen to see if any important message pops up. ((Marcus Wilburn))
  369. [2020-01-26 20:32:06] [Output] : ★ The machine beeps, upon glancing at the screen, Marcus squints his eyes as he ((Marcus Wilburn))
  370. [2020-01-26 20:32:22] [Output] : ★ reads the pop up message saying that the cycle is done. ((Marcus Wilburn))
  371. [2020-01-26 20:33:30] [Output] : ★ Marcus Wilburn turns it off and pulls the lid open before using a dry towel to slightly clean the
  372. [2020-01-26 20:33:44] [Output] : ★ block before lifting it back to the workbench. ((Marcus Wilburn))
  373. [2020-01-26 20:38:09] [Output] : ★ Marcus Wilburn fits his drill with a chamfer cone and uses it to chamfer the edges of both the top and
  374. [2020-01-26 20:38:24] [Output] : ★ the bottom of the cylinders to avoid damaging the piston rings. ((Marcus Wilburn))
  375. [2020-01-26 20:38:53] [Output] : ★ Marcus Wilburn places the drill aside and admires the now clean and shiny engine block.
  376. 2020-01-26 21:41:34] [Output] : ★ Marcus Wilburn carries the inline six and moves it on the transmission jack's plate.
  377. [2020-01-26 21:41:55] [Output] : ★ Marcus Wilburn straps it down and carts the tranny jack near the engine mount.
  378. [2020-01-26 21:42:39] [Output] : ★ Marcus Wilburn lines the flywheel side of the engine with the engine stand's mounting arms.
  379. [2020-01-26 21:43:11] [Output] : ★ Marcus Wilburn pumps up the lever to raise the engine up in order to match the mounting arms level.
  380. [2020-01-26 21:43:34] [Output] : ★ Marcus Wilburn fits the mounting arms on and tightens the bolts to secure it before undoing the jack
  381. [2020-01-26 21:43:40] [Output] : ★ straps and pushing it out of the way. ((Marcus Wilburn))
  382. [2020-01-26 21:48:49] [Output] : ★ Marcus Wilburn grabs a carton box branded with ECS tuning and placing it on the workbench before
  383. [2020-01-26 21:49:00] [Output] : ★ tearing it open and taking out two smaller boxers. ((Marcus Wilburn))
  384. [2020-01-26 21:49:27] [Output] : ★ Marcus Wilburn opens the said boxes and extracts their content as it appears to be six pistons with their
  385. [2020-01-26 21:50:41] [Output] : ★ rings, connecting bearings, connecting rods and main bearings crank shells. ((Marcus Wilburn))
  386. [2020-01-26 21:51:08] [Output] : ★ Marcus Wilburn starts unwrapping the plastic off of the parts and laying them on the workbench
  387. [2020-01-26 21:51:11] [Output] : ★ organized. ((Marcus Wilburn))
  388. [2020-01-26 21:51:43] [Output] : ★ Marcus Wilburn uses the special tool to knock the stock crank shells out of their place and fits on the
  389. [2020-01-26 21:51:46] [Output] : ★ new ones. ((Marcus Wilburn))
  390. [2020-01-26 21:55:56] [Output] : ★ Marcus Wilburn pushes on the new crank shells until they snap in place.
  391. [2020-01-26 21:56:46] [Output] : ★ Marcus Wilburn reaches out to an alcohol bottle and twists the cap off, he soaks a clean fiberglass
  392. [2020-01-26 21:57:09] [Output] : ★ towel with alcohol and uses it to clean the sides of the connecting rods where the ((Marcus Wilburn))
  393. [2020-01-26 21:57:17] [Output] : ★ bearings are supposed to be. ((Marcus Wilburn))
  394. [2020-01-26 21:57:39] [Output] : ★ Marcus Wilburn fits the bearings in place and uses both thumbs to push them in until they snap and lock
  395. [2020-01-26 21:57:41] [Output] : ★ there. ((Marcus Wilburn))
  396. [2020-01-26 21:57:54] [Output] : ★ Marcus Wilburn puts the alcohol bottle aside as he twists the cap back on.
  397. [2020-01-26 22:00:24] [Output] : ★ Marcus Wilburn grabs a bottle of assembly lube and squeeze it to put some lube on the holes of
  398. [2020-01-26 22:00:35] [Output] : ★ the connecting rods where the pin is supposed to go. ((Marcus Wilburn))
  399. [2020-01-26 22:01:03] [Output] : ★ Marcus Wilburn uses his fingers to spread the lube evenly, he grabs a clip and forces it in place in one
  400. [2020-01-26 22:01:13] [Output] : ★ side of the pin holes. ((Marcus Wilburn))
  401. [2020-01-26 22:01:27] [Output] : ★ Marcus Wilburn then grabs the pin itself and lubricates it as he gets it ready to go.
  402. [2020-01-26 22:01:47] [Output] : ★ Marcus Wilburn inserts it in the hole, the pin secures the piston to the connecting rod.
  403. [2020-01-26 22:02:48] [Output] : ★ Marcus Wilburn grabs a clip and puts it on the other hole now that the pin is inside, that's one piston and
  404. [2020-01-26 22:03:07] [Output] : ★ rod ready to go, he repeats the same with the rest of the five pistons and rods assemblies. ((Marcus Wilburn))
  405. [2020-01-26 22:03:36] [Output] : ★ Marcus Wilburn puts them aside and carts the engine block to the painting booth.
  406. [2020-01-26 22:04:15] [Output] : ★ Marcus Wilburn uses paint tape to cover both decks along with other holes where he doesn't want
  407. [2020-01-26 22:04:17] [Output] : ★ paint. ((Marcus Wilburn))
  408. [2020-01-26 22:04:48] [Output] : ★ Marcus Wilburn double checks everything and fills the paint sprayer tank with heat resistant primer, he
  409. [2020-01-26 22:05:10] [Output] : ★ then connects it to the hose from the air compressor and turns it on. ((Marcus Wilburn))
  410. [2020-01-26 22:05:42] [Output] : ★ Marcus Wilburn sprays primer across the block, not worried about anything since the place where paint isn't
  411. [2020-01-26 22:05:46] [Output] : ★ needed are covered. ((Marcus Wilburn))
  412. [2020-01-26 22:05:58] [Output] : ★ Marcus Wilburn finishes the first coat, he allows it to drain before going for a second coat.
  413. [2020-01-26 22:06:34] [Output] : ★ Marcus Wilburn removes the tank with the primer and gets a tank with bright red as he fits it on
  414. [2020-01-26 22:06:44] [Output] : ★ the sprayer and does an even first coat on the block. ((Marcus Wilburn))
  415. [2020-01-26 22:07:06] [Output] : ★ Marcus Wilburn gives that coat about five minutes to drain and does his second coat.
  416. [2020-01-26 22:09:38] [Output] : ★ Marcus Wilburn turns off the air compressor and puts the painting tools aside before carting the
  417. [2020-01-26 22:09:58] [Output] : ★ engine mount back to the workbench, he gives the second coat time before undoing ((Marcus Wilburn))
  418. [2020-01-26 22:10:59] [Output] : ★ the paint tape so that nothing sweats on places where paint is unwanted. ((Marcus Wilburn))
  419. [2020-01-26 22:12:01] [Output] : ★ Marcus Wilburn grabs the first piston and the first ring which is the oil spring ring that prevents oil
  420. [2020-01-26 22:12:08] [Output] : ★ from leaking in the cylinder. ((Marcus Wilburn))
  421. [2020-01-26 22:12:45] [Output] : ★ Marcus Wilburn installs the second cast iron ring gently as he expands it instead of twisting it
  422. [2020-01-26 22:12:58] [Output] : ★ being aware that these may break if they get twisted like the rest of the ((Marcus Wilburn))
  423. [2020-01-26 22:13:01] [Output] : ★ ring types. ((Marcus Wilburn))
  424. [2020-01-26 22:13:43] [Output] : ★ Marcus Wilburn fits the top ring on the piston head and does the same process with the rest
  425. [2020-01-26 22:14:34] [Output] : ★ of the pistons, he gets them all mounted with rings before grabbing a marker and ((Marcus Wilburn))
  426. [2020-01-26 22:14:50] [Output] : ★ labeling them down with the number of each piston and a small arrow to indicate ((Marcus Wilburn))
  427. [2020-01-26 22:15:00] [Output] : ★ the direction they'll be mounted in the engine. ((Marcus Wilburn))
  428. [2020-01-26 22:15:36] [Output] : ★ Marcus Wilburn puts the marker aside and turns the engine stand to get the block upside down.
  429. [2020-01-26 22:17:09] [Output] : ★ Marcus Wilburn takes the crankshaft he earlier removed and sits it back in place.
  430. [2020-01-26 22:17:52] [Output] : ★ Marcus Wilburn then removes it as he only placed it there to test fit the bearings he earlier installed.
  431. [2020-01-26 22:18:06] [Output] : ★ Marcus Wilburn grabs the bottle of lube and places some on each bearing before reinstalling
  432. [2020-01-26 22:18:41] [Output] : ★ the thrust barings and spreading the lube around with his fingers. ((Marcus Wilburn))
  433. [2020-01-26 22:19:00] [Output] : ★ Marcus Wilburn grabs the crankshaft and places it where it's supposed to be.
  434. [2020-01-26 22:19:46] [Output] : ★ Marcus Wilburn squirts assembly lube on the main bearings and as always spreads the lube with his index.
  435. [2020-01-26 22:20:20] [Output] : ★ Marcus Wilburn puts the main caps in place and heads to a corner of the garage.
  436. [2020-01-26 22:20:52] [Output] : ★ Marcus Wilburn bends over and hauls a box branded with "APR Main Studs" he puts the box on the
  437. [2020-01-26 22:22:00] [Output] : ★ table and opens it as he takes the bolts out of their plastic wrap and inserts them in the ((Marcus Wilburn))
  438. [2020-01-26 22:22:16] [Output] : ★ mounting holes of the main caps. ((Marcus Wilburn))
  439. [2020-01-26 22:22:31] [Output] : ★ Marcus Wilburn fits them with the washers and nuts and uses his impact wrench to tightens these
  440. [2020-01-26 22:22:34] [Output] : ★ suckers in place. ((Marcus Wilburn))
  441. [2020-01-26 22:22:54] [Output] : ★ Marcus Wilburn gets his torque wrench and torques down the head studs to the specs available on the
  442. [2020-01-26 22:22:59] [Output] : ★ car owner manual. ((Marcus Wilburn))
  443. [2020-01-26 22:23:52] [Output] : ★ Marcus Wilburn uses the lever on the engine mount to turn the engine so that the crankshaft is facing
  444. [2020-01-26 22:24:02] [Output] : ★ down and he has clearance to cylinders. ((Marcus Wilburn))
  445. [2020-01-26 22:24:36] [Output] : ★ Marcus Wilburn gets a bottle of piston rings lubricant and lubricates all the cylinders as he pours in the
  446. [2020-01-26 22:24:48] [Output] : ★ product and spreads it with his fingers evenly. ((Marcus Wilburn))
  447. [2020-01-26 22:25:41] [Output] : ★ Marcus Wilburn puts the bottle aside and gets his assembly lube bottle and pours some of the gel
  448. [2020-01-26 22:25:54] [Output] : ★ on the connecting bearing. ((Marcus Wilburn))
  449. [2020-01-26 22:26:22] [Output] : ★ Marcus Wilburn rummages through the tools as he searches for his piston installation tool, he lubricates
  450. [2020-01-26 22:26:58] [Output] : ★ that sucker too and fits it on the piston before dropping the piston inside the first ((Marcus Wilburn))
  451. [2020-01-26 22:27:30] [Output] : ★ cylinder, he uses his thumbs to push it inside the cylinder. ((Marcus Wilburn))
  452. [2020-01-26 22:29:36] [Output] : ★ Marcus Wilburn kneels down and uses two bolts that came with the package to hold the rod cap
  453. [2020-01-26 22:29:53] [Output] : ★ in place, he fully tightens it using the impact wrench. ((Marcus Wilburn))
  454. [2020-01-26 22:30:25] [Output] : ★ Marcus Wilburn fits the piston installation tool on another piston and drops it in the cylinder as he
  455. [2020-01-26 22:30:42] [Output] : ★ pushes it inside with his fingers, he then installs the rod caps and does the same ((Marcus Wilburn))
  456. [2020-01-26 22:30:54] [Output] : ★ thing with the rest of the pistons to get them mounted up. ((Marcus Wilburn))
  457. [2020-01-26 22:31:20] [Output] : ★ Marcus Wilburn turns the lever on the engine mount until the crankshaft side is facing the ceiling.
  458. [2020-01-26 22:32:33] [Output] : ★ Marcus Wilburn takes the torque wrench and torques down the two ARP bolts mounting each rod cap.
  459. [2020-01-26 22:32:47] [Output] : ★ Marcus Wilburn places the tool aside and yawns as he's been working for quite a while.
  460. [2020-01-26 22:38:15] [Output] : ★ Marcus Wilburn looks at the cylinder head for a moment and approaches it as it appears to have
  461. [2020-01-26 22:38:20] [Output] : ★ no valves. ((Marcus Wilburn))
  462. [2020-01-26 22:39:39] [Output] : ★ Marcus Wilburn slides the valves back inside the cylinder head, he goes through each of the twenty
  463. [2020-01-26 22:39:50] [Output] : ★ four valves as he places them back in their slots. ((Marcus Wilburn))
  464. [2020-01-26 22:40:32] [Output] : ★ Marcus Wilburn opens a box with the new springs and retainers for the valves, he extracts them
  465. [2020-01-26 22:41:00] [Output] : ★ of the workbench. ((Marcus Wilburn))
  466. [2020-01-26 22:41:29] [Output] : ★ Marcus Wilburn gets the springs and retainers ready to go and places a pair on each of the valves as
  467. [2020-01-26 22:41:46] [Output] : ★ he casually sighs, obviously being annoyed at the rather repetitive task but seemingly ((Marcus Wilburn))
  468. [2020-01-26 22:42:00] [Output] : ★ patient knowing that it's worth it. ((Marcus Wilburn))
  469. [2020-01-26 22:42:45] [Output] : ★ Marcus Wilburn grabs his valve spring compressor tool and fits it on the first valve before compressing the
  470. [2020-01-26 22:43:40] [Output] : ★ new spring and a can of axle grease, he opens it and gets a screwdriver, dips it in there ((Marcus Wilburn))
  471. [2020-01-26 22:44:21] [Output] : ★ to get a little dab of grease on the tip. ((Marcus Wilburn))
  472. [2020-01-26 22:46:11] [Output] : ★ Marcus Wilburn puts that dab in the valve keeper, it acts like glue but it's in fact grease that wouldn't
  473. [2020-01-26 22:46:32] [Output] : ★ hurt the engine internals. ((Marcus Wilburn))
  474. [2020-01-26 22:47:06] [Output] : ★ Marcus Wilburn places the valve keeper on the tip of the valve itself, he does the same with the other
  475. [2020-01-26 22:47:11] [Output] : ★ keeper and puts it on. ((Marcus Wilburn))
  476. [2020-01-26 22:48:17] [Output] : ★ Marcus Wilburn slowly starts releasing tension on the valve spring compressor and takes off the tool
  477. [2020-01-26 22:48:36] [Output] : ★ once the valve spring is all decompressed and in place. ((Marcus Wilburn))
  478. [2020-01-26 22:50:49] [Output] : ★ Marcus Wilburn keeps on fitting the valves with new springs, retainers and keeprs and once he's done
  479. [2020-01-26 22:51:19] [Output] : ★ he hauls the cylinder head to a CNC machine and puts it between the machine's arms ((Marcus Wilburn))
  480. [2020-01-26 22:51:23] [Output] : ★ as he turns it on. ((Marcus Wilburn))
  481. [2020-01-26 22:51:46] [Output] : ★ Marcus Wilburn looks at the screen, he enters different settings before pressing on the start button, the
  482. [2020-01-26 22:52:18] [Output] : ★ machine's plate drops against the bottom of the cylinder head and starts resurfacing it. ((Marcus Wilburn))
  483. [2020-01-26 22:52:30] [Output] : ★ It shortly beeps after, indicating that the job is finished. ((Marcus Wilburn))
  484. [2020-01-26 22:52:50] [Output] : ★ Marcus Wilburn takes the cylinder head and transports it back to the workbench as he places it there.
  485. [2020-01-26 22:53:15] [Output] : ★ Marcus Wilburn takes the new gasket out of its box along with the head studs.
  486. [2020-01-26 22:54:08] [Output] : ★ Marcus Wilburn places the gasket on top of the block and adjusts it properly before grabbing the
  487. [2020-01-26 22:54:19] [Output] : ★ cylinder head and moving it directly above it. ((Marcus Wilburn))
  488. [2020-01-26 22:54:33] [Output] : ★ Marcus Wilburn places the washers and starts inserting the head studs in the holes.
  489. [2020-01-26 22:55:16] [Output] : ★ Marcus Wilburn puts the nuts on the head studs and tightens them using an impact wrench before
  490. [2020-01-26 22:55:51] [Output] : ★ getting a big torque wrench and torquing the head studs to 85 ft-lb. ((Marcus Wilburn))
  491. [2020-01-26 22:56:48] [Output] : ★ Marcus Wilburn sets the torque wrench aside and takes the two new cams out of their box.
  492. [2020-01-26 22:57:08] [Output] : ★ Marcus Wilburn sits them in place after lubricating them with assembly lube.
  493. [2020-01-26 22:57:41] [Output] : ★ Marcus Wilburn puts the cam seals on along with the cam caps.
  494. [2020-01-26 22:58:24] [Output] : ★ Marcus Wilburn inserts the cam caps bolts in the holes and uses his impact wrench to tighten these
  495. [2020-01-26 22:58:42] [Output] : ★ being super careful and slow as he's not sure about the cam orientation and doesn't want ((Marcus Wilburn))
  496. [2020-01-26 22:58:46] [Output] : ★ to break these. ((Marcus Wilburn))
  497. [2020-01-26 22:59:39] [Output] : ★ Marcus Wilburn puts the oil pump assembly in place and hand tightens the bolts before reaching out to
  498. [2020-01-26 22:59:50] [Output] : ★ the impact wrench to finish tightening the bolts. ((Marcus Wilburn))
  499. [2020-01-26 23:00:24] [Output] : ★ Marcus Wilburn places the main seal back on and struggles to tighten these.
  500. [2020-01-26 23:01:25] [Output] : ★ Marcus Wilburn grabs the bedplate after turning the engine upside down, he lines it up with the holes and
  501. [2020-01-26 23:01:31] [Output] : ★ puts the bolts removed earlier. ((Marcus Wilburn))
  502. [2020-01-26 23:01:47] [Output] : ★ Marcus Wilburn torques them down with the help of his big torque wrench.
  503. [2020-01-26 23:02:33] [Output] : ★ Marcus Wilburn puts the oil baffle back on and tightens its bolts prior to remounting the oil strainer and
  504. [2020-01-26 23:02:41] [Output] : ★ tightening the bolts that hold it in place ((Marcus Wilburn))
  505. [2020-01-26 23:03:04] [Output] : ★ Marcus Wilburn inserts the oil level sensor in place.
  506. [2020-01-26 23:03:36] [Output] : ★ Marcus Wilburn gets a bottle of silicone gasket maker and spreads it around the mating surface of
  507. [2020-01-26 23:03:47] [Output] : ★ the oil pan before putting it on. ((Marcus Wilburn))
  508. [2020-01-26 23:03:58] [Output] : ★ Marcus Wilburn tightens the bolts securing the oil pan to the block.
  509. [2020-01-26 23:04:42] [Output] : ★ Marcus Wilburn places the exhaust cam gear on and uses a monkey wrench to hold the exhaust cam
  510. [2020-01-26 23:04:53] [Output] : ★ still as he secures the gear by tightening the bolt. ((Marcus Wilburn))
  511. [2020-01-26 23:05:57] [Output] : ★ Marcus Wilburn does the same for the intake VANOS gear, he mounts it in place and holds the intake cam
  512. [2020-01-26 23:06:03] [Output] : ★ still with the monkey wrench. ((Marcus Wilburn))
  513. [2020-01-26 23:06:51] [Output] : ★ Marcus Wilburn installs the crankshaft pulley and uses the impact wrench to tighten it as he fits the
  514. [2020-01-26 23:07:01] [Output] : ★ timing belt on. ((Marcus Wilburn))
  515. [2020-01-26 23:07:29] [Output] : ★ Marcus Wilburn gets the automatic tensioner and puts it on before securing its bolts with the impact
  516. [2020-01-26 23:07:31] [Output] : ★ wrench. ((Marcus Wilburn))
  517. [2020-01-26 23:08:54] [Output] : ★ Marcus Wilburn grabs the solid oil line that feeds oil to the variable cam he fits it on and tightens it
  518. [2020-01-26 23:08:56] [Output] : ★ accordingly. ((Marcus Wilburn))
  519. [2020-01-26 23:09:31] [Output] : ★ Marcus Wilburn inserts the vanos selenoid in.
  520. [2020-01-26 23:10:25] [Output] : ★ Marcus Wilburn fits the valve cover with the rubber gasket and puts it on as he secures it by tightening th
  521. [2020-01-26 23:10:29] [Output] : ★ the bolts. ((Marcus Wilburn))
  522. [2020-01-26 23:10:46] [Output] : ★ Marcus Wilburn installs the knock sensors on the engine as he yawns again.
  523. [2020-01-26 23:12:14] [Output] : ★ Marcus Wilburn places the timing covers on after installing the water pumps he fixes these two tightly
  524. [2020-01-26 23:12:26] [Output] : ★ and looks back at the car as the engine is almost ready to go back in. ((Marcus Wilburn))
  525. [2020-01-27 00:29:44] [Output] : ★ Marcus Wilburn carts the engine hoist near the engine stand and places two bolts in the holes of
  526. [2020-01-27 00:30:12] [Output] : ★ the exhaust manifold and two in the holes of the intake manifold, he runs the hoist chain ((Marcus Wilburn))
  527. [2020-01-27 00:30:47] [Output] : ★ through them and secures it before undoing the engine mount arms to separate the ((Marcus Wilburn))
  528. [2020-01-27 00:30:54] [Output] : ★ engine and the engine stand. ((Marcus Wilburn))
  529. [2020-01-27 00:31:33] [Output] : ★ Marcus Wilburn carts the engine hoist in front of the car and grabs a box as he pops it open and takes out
  530. [2020-01-27 00:31:44] [Output] : ★ the new engine and transmission mounts. ((Marcus Wilburn))
  531. [2020-01-27 00:31:59] [Output] : ★ Marcus Wilburn gets in the bay himself and uses his impact wrench to secure the mounts to the car
  532. [2020-01-27 00:32:02] [Output] : ★ frame. ((Marcus Wilburn))
  533. [2020-01-27 00:32:29] [Output] : ★ Marcus Wilburn steps out and slowly lowers the rebuilt engine on its mounts.
  534. [2020-01-27 00:32:45] [Output] : ★ Marcus Wilburn watches the process and makes sure the engine doesn't touch anything.
  535. [2020-01-27 00:33:07] [Output] : ★ Marcus Wilburn undoes the hoist chain and pushes the hoist itself away, securing the engine to the new
  536. [2020-01-27 00:33:10] [Output] : ★ mounts. ((Marcus Wilburn))
  537. [2020-01-27 00:33:55] [Output] : ★ Marcus Wilburn unboxes the intake parts and slots the new injectors in their place on the new individual
  538. [2020-01-27 00:34:03] [Output] : ★ throttle body.'s rail. ((Marcus Wilburn))
  539. [2020-01-27 00:34:43] [Output] : ★ Marcus Wilburn heads to the engine and connects the individual throttle body in place as he tightens
  540. [2020-01-27 00:34:48] [Output] : ★ the bolts to secure it. ((Marcus Wilburn))
  541. [2020-01-27 00:35:07] [Output] : ★ Marcus Wilburn reaches for the end of the throttle cable and hooks it to the ITB as he tightens it
  542. [2020-01-27 00:35:35] [Output] : ★ Marcus Wilburn before connecting the air hose from the new air intake kit to the ITB inlet
  543. [2020-01-27 00:35:45] [Output] : ★ Marcus Wilburn and using the clamp to secure it.
  544. [2020-01-27 00:36:06] [Output] : ★ Marcus Wilburn reconnects the fuel feed and return lines to their ports on the ITB's fuel rail, he then
  545. [2020-01-27 00:36:14] [Output] : ★ tightens the clamps on these two. ((Marcus Wilburn))
  546. [2020-01-27 00:37:13] [Output] : ★ Marcus Wilburn sighs as he then starts reconnecting the main wiring loom along with the coil plug and all
  547. [2020-01-27 00:37:27] [Output] : ★ the sensors such as the MAF and all. ((Marcus Wilburn))
  548. [2020-01-27 00:38:05] [Output] : ★ Marcus Wilburn grabs the old radiator and drops it back in place, the fan is still connected to it.
  549. [2020-01-27 00:38:24] [Output] : ★ Marcus Wilburn tightens the bolts that secure the radiator mounting brackets to the car's frame.
  550. [2020-01-27 00:38:35] [Output] : ★ Marcus Wilburn reconnects the radiator fan connector.
  551. [2020-01-27 00:39:14] [Output] : ★ Marcus Wilburn takes a lift remote out of his pocket and presses on a button to raise the car up
  552. [2020-01-27 00:39:21] [Output] : ★ about a meter above the ground. ((Marcus Wilburn))
  553. [2020-01-27 00:40:01] [Output] : ★ Marcus Wilburn moves the new sequentiel transmission on the transmission jack's plate and carts it beneath
  554. [2020-01-27 00:40:24] [Output] : ★ the vehicle before getting his new clutch and fly wheel out of their box. ((Marcus Wilburn))
  555. [2020-01-27 00:40:46] [Output] : ★ Marcus Wilburn mounts these two in place and secures them accordingly as he pushes the tranny
  556. [2020-01-27 00:41:14] [Output] : ★ against them and uses the impact wrench to secure the bolts that hold the bellhousing to the ((Marcus Wilburn))
  557. [2020-01-27 00:41:18] [Output] : ★ engine block. ((Marcus Wilburn))
  558. [2020-01-27 00:41:59] [Output] : ★ Marcus Wilburn uses his impact wrench to loosen the four bolts securing the OEM driveshaft to the diff.
  559. [2020-01-27 00:42:15] [Output] : ★ Marcus Wilburn drops the old driveshaft and pushes it away.
  560. [2020-01-27 00:42:36] [Output] : ★ Marcus Wilburn undoes the bolts on both sides of the axle shafts and disconnects these two as well.
  561. [2020-01-27 00:43:00] [Output] : ★ Marcus Wilburn takes off the differentiel with the assistance of his impact wrench and a socket of
  562. [2020-01-27 00:43:26] [Output] : ★ the right size, he emits a sigh as he drops the differientel housing out and undoes the ((Marcus Wilburn))
  563. [2020-01-27 00:43:29] [Output] : ★ cover bolts. ((Marcus Wilburn))
  564. [2020-01-27 00:43:48] [Output] : ★ Marcus Wilburn wiggles the stock diff out of place and places the new performance one inside after boxing
  565. [2020-01-27 00:43:52] [Output] : ★ it. ((Marcus Wilburn))
  566. [2020-01-27 00:44:12] [Output] : ★ Marcus Wilburn makes quite a mess with differentiel oil but he doesn't care at this moment, he's already
  567. [2020-01-27 00:44:14] [Output] : ★ tired. ((Marcus Wilburn))
  568. [2020-01-27 00:44:37] [Output] : ★ Marcus Wilburn puts the cover back on and tightens the bolts again before lining up the differentiel
  569. [2020-01-27 00:44:59] [Output] : ★ housing hanger with the holes on the car frame and hand tightening the bolts, prior to ((Marcus Wilburn))
  570. [2020-01-27 00:45:07] [Output] : ★ using his impact wrench to fix it in place. ((Marcus Wilburn))
  571. [2020-01-27 00:45:31] [Output] : ★ Marcus Wilburn unboxes the two new axle shafts and puts them in place as he fastens the bolts on
  572. [2020-01-27 00:45:35] [Output] : ★ each side of the axles. ((Marcus Wilburn))
  573. [2020-01-27 00:45:58] [Output] : ★ Marcus Wilburn grabs the new driveshaft and gets beneath the car as he hand tightens the four
  574. [2020-01-27 00:46:18] [Output] : ★ bolts on the side of the diff, he then moves up to the transmission side and does the same ((Marcus Wilburn))
  575. [2020-01-27 00:46:27] [Output] : ★ to mount the driveshaft in place. ((Marcus Wilburn))
  576. [2020-01-27 00:46:50] [Output] : ★ Marcus Wilburn starts reconnecting the transmission sensors and plugs.
  577. [2020-01-27 00:47:07] [Output] : ★ Marcus Wilburn pushes himself up and gets a power drill before crawling back beneath the car
  578. [2020-01-27 00:47:37] [Output] : ★ and drilling a hole through the firewall to get the clutch pedal installed. ((Marcus Wilburn))
  579. [2020-01-27 00:47:59] [Output] : ★ Marcus Wilburn test fits the clutch pedal bracket and drills the necessary mounting holes before hand
  580. [2020-01-27 00:48:30] [Output] : ★ tightening these and finishing with the impact wrench to fully install the clutch pedal on ((Marcus Wilburn))
  581. [2020-01-27 00:48:43] [Output] : ★ his originally automatic vehicle. ((Marcus Wilburn))
  582. [2020-01-27 00:49:12] [Output] : ★ Marcus Wilburn hooks the clutch cable on the pedal and on the clutch on the other side before
  583. [2020-01-27 00:49:26] [Output] : ★ adjusting the clutch settings to ensure the pedal is fully working. ((Marcus Wilburn))
  584. [2020-01-27 00:50:17] [Output] : ★ Marcus Wilburn pushes himself up and drops the vehicle on four wheels.
  585. [2020-01-27 00:50:48] [Output] : ★ Marcus Wilburn grabs the turbo manifold and fits it on the engine head as he secures it using the bolts
  586. [2020-01-27 00:50:53] [Output] : ★ that came with it. ((Marcus Wilburn))
  587.  
  588. [2020-01-27 00:51:23] [Output] : ★ Marcus Wilburn gets the tubocharger and sits it on the turbo manifold after putting the gasket, he then
  589. [2020-01-27 00:51:34] [Output] : ★ tightens the turbocharger bolts. ((Marcus Wilburn))
  590. [2020-01-27 00:52:19] [Output] : ★ Marcus Wilburn disconnects the air hose from the ITB realizing how silly he is, he then connects it to the
  591. [2020-01-27 00:52:38] [Output] : ★ turbo air inlet. ((Marcus Wilburn))
  592. [2020-01-27 00:53:09] [Output] : ★ Marcus Wilburn gets beneath the car and uses his drill with the right size bit to drill two holes in
  593. [2020-01-27 00:53:24] [Output] : ★ the engine pan, he uses teflon tape and plugs to taps to it. ((Marcus Wilburn))
  594. [2020-01-27 00:53:43] [Output] : ★ Marcus Wilburn runs oil feed and return lines to the compressor housing.
  595. [2020-01-27 00:54:34] [Output] : ★ Marcus Wilburn unboxes the intercooler kit and test fits it once before starting to run pipes beginning
  596. [2020-01-27 00:55:09] [Output] : ★ from the ITB inlet port all the way to the turbo intake outlet. ((Marcus Wilburn))
  597. [2020-01-27 00:56:25] [Output] : ★ Marcus Wilburn ensures the connection goes through the intercooler and cools the boosted air.
  598. [2020-01-27 00:56:41] [Output] : ★ Marcus Wilburn puts on protective eye wear and grabs a torch set as he turns it on and adjusts
  599. [2020-01-27 00:57:03] [Output] : ★ the oxygen and gas levels, he then cuts a hole through the hood of the car, letting the ((Marcus Wilburn))
  600. [2020-01-27 00:57:09] [Output] : ★ metal cool down. ((Marcus Wilburn))
  601. [2020-01-27 00:57:34] [Output] : ★ Marcus Wilburn grabs the front bumper meanwhile, he gets in front of the car and fits it on before actually
  602. [2020-01-27 00:57:45] [Output] : ★ securing it with the screws that came with it. ((Marcus Wilburn))
  603. [2020-01-27 00:58:12] [Output] : ★ Marcus Wilburn uses a saw to cut an area of the bumper so that the intercooler pokes out.
  604. [2020-01-27 00:58:34] [Output] : ★ Marcus Wilburn grabs hold of the hood and hauls it to the car as he rests it in place and temporarily holds
  605. [2020-01-27 00:58:54] [Output] : ★ it with his left hand and the hood prop, using his free hand to tighten the four bolts that ((Marcus Wilburn))
  606. [2020-01-27 00:58:59] [Output] : ★ hold it in place. ((Marcus Wilburn))
  607. [2020-01-27 00:59:27] [Output] : ★ Marcus Wilburn connects the blow off valve to the flange on the turbo manifold before securing it and
  608. [2020-01-27 00:59:37] [Output] : ★ drilling a hole in the vacuum hose. ((Marcus Wilburn))
  609. [2020-01-27 01:00:07] [Output] : ★ Marcus Wilburn then hooks the vacuum hose with a t connector, running another hose all the way to
  610. [2020-01-27 01:00:13] [Output] : ★ the blow off valve. ((Marcus Wilburn))
  611. [2020-01-27 01:01:33] [Output] : ★ Marcus Wilburn grabs a pipe from the DIY exhaust kit and uses his short the said U-pipe.
  612. [2020-01-27 01:01:50] [Output] : ★ Marcus Wilburn test fits it on the turbo exhaust outlet, making sure it goes through the hole he
  613. [2020-01-27 01:01:55] [Output] : ★ cut on the hood. ((Marcus Wilburn))
  614. [2020-01-27 01:02:19] [Output] : ★ Marcus Wilburn puts on eyewear and grabs the TIC welding post near the car as he welds the exhaust
  615. [2020-01-27 01:02:31] [Output] : ★ pipe to the turbo's outlet carefully. ((Marcus Wilburn))
  616. [2020-01-27 01:02:44] [Output] : ★ Marcus Wilburn turns off the welder and puts it aside as he takes off the eyewear.
  617. [2020-01-27 01:03:10] [Output] : ★ Marcus Wilburn carries the battery and puts it in the bay as he secures the strap holding it in place
  618. [2020-01-27 01:04:08] [Output] : ★ and moves to the passenger side, opening the door and getting his head beneath the ((Marcus Wilburn))
  619. [2020-01-27 01:04:24] [Output] : ★ passenger seat, starting to undo the bolts securing the seat rail to the frame. ((Marcus Wilburn))
  620. [2020-01-27 01:04:45] [Output] : ★ Marcus Wilburn carefully eases the passenger seat out of the door and puts it on the ground.
  621. [2020-01-27 01:05:21] [Output] : ★ Marcus Wilburn moves to the driver door, he does exactly the same thing and heads to the driver
  622. [2020-01-27 01:05:25] [Output] : ★ door opening it. ((Marcus Wilburn))
  623. [2020-01-27 01:05:42] [Output] : ★ Marcus Wilburn loosens the rails of the driver seat and takes the seat out carefully.
  624. [2020-01-27 01:05:59] [Output] : ★ Marcus Wilburn tosses it aside and emits a sigh as he pops the trunk open.
  625. [2020-01-27 01:06:21] [Output] : ★ Marcus Wilburn uses his impact wrench to loosen the bolts that secure the rear seats to the frame.
  626. [2020-01-27 01:06:40] [Output] : ★ Marcus Wilburn gets to the driver door and gets the back part of the back seat out of the vehicle
  627. [2020-01-27 01:06:45] [Output] : ★ placing it aside. ((Marcus Wilburn))
  628. [2020-01-27 01:06:59] [Output] : ★ Marcus Wilburn removes the seater part of the backseats afterwards.
  629. [2020-01-27 01:07:16] [Output] : ★ Marcus Wilburn reveals the cover of the fuel tank.
  630. [2020-01-27 01:07:51] [Output] : ★ Marcus Wilburn unscrews the bolts of the tank cover and places a dry towel around as he disconnects the
  631. [2020-01-27 01:08:01] [Output] : ★ fuel pump wiring connector. ((Marcus Wilburn))
  632. [2020-01-27 01:08:23] [Output] : ★ Marcus Wilburn fishes the pump assembly out of place after undoing the fuel lines, he unscrews the lid
  633. [2020-01-27 01:08:31] [Output] : ★ of the assembly and takes the stock pump out. ((Marcus Wilburn))
  634. [2020-01-27 01:08:53] [Output] : ★ Marcus Wilburn unboxes the new one and fits it with the aftermarket sleeve before dropping it in the fuel
  635. [2020-01-27 01:09:11] [Output] : ★ tank, he reconnects the fuel lines along with the wire connector before covering the whole ((Marcus Wilburn))
  636. [2020-01-27 01:09:38] [Output] : ★ assembly and fastening the bolts with the impact wrench. ((Marcus Wilburn))
  637. [2020-01-27 01:10:11] [Output] : ★ Marcus Wilburn places the aftermarket seat rails where they're supposed to go and lines it up with
  638. [2020-01-27 01:10:24] [Output] : ★ the mounting holes before securing it by tightening the bolts. ((Marcus Wilburn))
  639. [2020-01-27 01:10:45] [Output] : ★ Marcus Wilburn gets the driver OMP seat and eases it inside the car through the driver door, resting it
  640. [2020-01-27 01:11:00] [Output] : ★ on the mounting bracket. ((Marcus Wilburn))
  641. [2020-01-27 01:11:23] [Output] : ★ Marcus Wilburn secures the bolts to hold the racing seat in place and does exactly the same to the
  642. [2020-01-27 01:11:29] [Output] : ★ passenger side. ((Marcus Wilburn))
  643. [2020-01-27 01:11:39] [Output] : ★ Marcus Wilburn tends to be rather annoyed when doing repetitive tasks.
  644. [2020-01-27 01:12:22] [Output] : ★ Marcus Wilburn heads to the front of the car and reconnects the battery terminal as he screws them tight.
  645. [2020-01-27 01:12:49] [Output] : ★ Marcus Wilburn shuts the hood, the trunk and the rest of the door except the driver door.
  646. [2020-01-27 01:13:16] [Output] : ★ Marcus Wilburn disengages the hand brakes and pushes the car on the dyno before hopping inside and getting
  647. [2020-01-27 01:13:34] [Output] : ★ the floor mat on the passenger door off, placing it aside and revealing the stock ((Marcus Wilburn))
  648. [2020-01-27 01:13:48] [Output] : ★ ECU, he unscrews the last and disconnects the harnesses going to it. ((Marcus Wilburn))
  649. [2020-01-27 01:14:12] [Output] : ★ Marcus Wilburn slots the new aftermarket in place and secures the screws before plugging the
  650. [2020-01-27 01:14:17] [Output] : ★ harnesses back on it. ((Marcus Wilburn))
  651. [2020-01-27 01:14:51] [Output] : ★ Marcus Wilburn hops out of the car and gets the dyno straps strapped to the car axles to get it
  652. [2020-01-27 01:15:04] [Output] : ★ not to move during the runs. ((Marcus Wilburn))
  653. [2020-01-27 01:15:32] [Output] : ★ Marcus Wilburn turns on his PC and places it on his lap as he sits on the driver seat.
  654. [2020-01-27 01:15:52] [Output] : ★ Marcus Wilburn hops out and fits the knock sensor along with the rest of the rest dyno sensors to
  655. [2020-01-27 01:15:55] [Output] : ★ the car. ((Marcus Wilburn))
  656. [2020-01-27 01:16:26] [Output] : ★ Marcus Wilburn opens the tuner software and goes on the general tab as he sets the RPM limit to
  657. [2020-01-27 01:16:33] [Output] : ★ 9000. ((Marcus Wilburn))
  658. [2020-01-27 01:16:55] [Output] : ★ Marcus Wilburn then moves to the fuel section and selects all of the boxes, tweaking the settings to fit
  659. [2020-01-27 01:17:02] [Output] : ★ with the new setup. ((Marcus Wilburn))
  660. [2020-01-27 01:17:21] [Output] : ★ Marcus Wilburn hits the turbo tab and fiddles with the boost, figuring out the best pressure to run.
  661. [2020-01-27 01:17:52] [Output] : ★ Marcus Wilburn then hits the igntion tab and and starts changing values aiming to achieve the perfect
  662. [2020-01-27 01:18:00] [Output] : ★ timing to avoid knock. ((Marcus Wilburn))
  663. [2020-01-27 01:18:44] [Output] : lmao
  664. [2020-01-27 01:18:44] [Output] : ★ Marcus Wilburn finally arrives to the air section, he plays with the values until they're more suitable.
  665. [2020-01-27 01:19:28] [Output] : ★ Marcus Wilburn saves the map and flashes it to the new aftermarket ECU before starting his
  666. [2020-01-27 01:19:54] [Output] : ★ car and consulting his phone to see what gear of his sequentiel gear box has a 1:1 ((Marcus Wilburn))
  667. [2020-01-27 01:20:11] [Output] : ★ ratio, he then slowly and carefully accelerates to the said gear and accelerates ((Marcus Wilburn))
  668. [2020-01-27 01:20:37] [Output] : ★ until he reaches the RPM limit, he eases off the throttle and lets the engine idle as he ((Marcus Wilburn))
  669. [2020-01-27 01:20:54] [Output] : ★ moves the PC back on his lap, he goes through the results carefully and tweaks the ((Marcus Wilburn))
  670. [2020-01-27 01:20:59] [Output] : ★ values. ((Marcus Wilburn))
  671. [2020-01-27 01:21:31] [Output] : ★ Marcus Wilburn goes for a second run after flashing the new map into the MegaSquirt, the results are
  672. [2020-01-27 01:21:44] [Output] : ★ improving and getting closer to his goals but there's still some knock. ((Marcus Wilburn))
  673. [2020-01-27 01:22:28] [Output] : ★ Marcus Wilburn tweaks the timing values and retards them.
  674. [2020-01-27 01:22:50] [Output] : ★ Marcus Wilburn goes through a third run, he bobs his head, clearly impressed by the results his
  675. [2020-01-27 01:22:53] [Output] : ★ build achieved. ((Marcus Wilburn))
  676. [2020-01-27 01:23:28] [Output] : ★ Marcus Wilburn hops out of the car and undoes the dyno belts, he pops the trunk open and does
  677. [2020-01-27 01:23:34] [Output] : ★ his signature. ((Marcus Wilburn))
  678. [2020-01-27 01:23:45] [Output] : ★ Marcus Wilburn tosses the spare tire aside as he speaks.
  679. [2020-01-27 01:23:52] [Output] : [English] Marcus Wilburn says: Weight reduction, nigga.
  680. [2020-01-27 01:24:12] [Output] : ★ Marcus Wilburn shuts the trunk and heads to the driver seat slowly backing out of the dyno.
  681. [2020-01-27 01:24:27] [Output] : ★ Marcus Wilburn takes the vehicle for a late night drive, enjoying the improvement.
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!